Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 162 views

    Eon 515 Troubleshooting Guide

    Uploaded by

    PREVISTO
    The document provides troubleshooting steps for issues with the secondary and primary circuits of the Eon 515 amplifier. For secondary circuits, it describes measuring voltages and checking for shorts in individual components. For primary circuits, it details checking MOSFETs and other parts for shorts, verifying switching waveforms, and ensuring proper voltages. It also lists three common early field failures: shorted devices from contamination, low gate drive at startup, and power up failures from a stuck relay.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Eon 515 Troubleshooting Guide

    Uploaded by

    PREVISTO
    162 views5 pages
    The document provides troubleshooting steps for issues with the secondary and primary circuits of the Eon 515 amplifier. For secondary circuits, it describes measuring voltages and checking for shorts in individual components. For primary circuits, it details checking MOSFETs and other parts for shorts, verifying switching waveforms, and ensuring proper voltages. It also lists three common early field failures: shorted devices from contamination, low gate drive at startup, and power up failures from a stuck relay.

    Original Description:

    APOSTILA

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides troubleshooting steps for issues with the secondary and primary circuits of the Eon 515 amplifier. For secondary circuits, it describes measuring voltages and checking for shorts in individual components. For primary circuits, it details checking MOSFETs and other parts for shorts, verifying switching waveforms, and ensuring proper voltages. It also lists three common early field failures: shorted devices from contamination, low gate drive at startup, and power up failures from a stuck relay.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    162 views5 pages

    Eon 515 Troubleshooting Guide

    Uploaded by

    PREVISTO
    The document provides troubleshooting steps for issues with the secondary and primary circuits of the Eon 515 amplifier. For secondary circuits, it describes measuring voltages and checking for shorts in individual components. For primary circuits, it details checking MOSFETs and other parts for shorts, verifying switching waveforms, and ensuring proper voltages. It also lists three common early field failures: shorted devices from contamination, low gate drive at startup, and power up failures from a stuck relay.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 5

    Eon 515 Troubleshooting Guide

    E.Bird/T.Walbert 1-15-09

    Secondary circuits.

    1. Start by doing a thorough visual examination of the assembly for any sign of damage.
    This will help guide you to the trouble area.

    2. Using an ohm-meter measure from TP601 (+VCC) to TP602 (Ground). It should


    measure over 2K and rising as it charges up the capacitors. If this reads near 0 ohms then
    you will need to remove the PWA from the heatsink and check for a silpad short.

    3. Using an ohm-meter measure from TP603 (-VCC) to TP602 (Ground). It should


    measure over 2K and rising as it charges up the capacitors. If this reads near 0 ohms then
    you will need to remove the PWA from the heatsink and check for a silpad short or a
    short between U402 and the heatsink.
    4. Using an ohm-meter measure from TP601 (+VCC) to TP603 (-VCC). It should
    measure over 2K and rising as it charges up the capacitors. If this reads near 0 ohms, then
    check Q370, Q371, Q372 and Q373 for shorts, and replace the damaged parts. If two of
    these MOSFETs are shorted then replacing them is all you will need to do to the
    amplifier section but you will need to check the power supply for damage.

    5. Connect a low voltage supply capable of +/-20Vdc to TP601 (+VCC),


    TP602(GROUND) and TP603(-VCC). Verify that the +15, -15, +5 and –5V regulators
    have the proper voltage output. If the voltage is low on any of these and there is not
    excessive current draw, then replace the regulator.

    6. Connect a 40K ohm resistor from D611 cathode (+VCC SENSE) to +VCC, with the
    supplies set to +/-20Vdc. This will allow the amplifier to start switching. Verify the
    switching waveforms at Q370 Drain pin and Q372 Drain pin are square and stable.
    Primary circuits.

    1. Using an ohm-meter check Q605 and Q606 for shorts. If these devices are shorted
    then check R626 and R628 which should read 10ohms. Next check Q601, Q602,
    Q603, Q604 for shorts and opens. If any of these are damaged then you will most
    likely need to replace the following parts along with the ones already identified.
    U603, R623, R624, U602, U609 and U 601.

    2. After replacing all failed parts, connect a power supply set to 13Vdc from +15V
    control to SMPSREF and place a 1K ohm resistor from U602 pin 2 to +15
    control. Verify that the signal at Q606 Gate is a square wave at approximately
    140KHz.
    3. Remove the 13V supply and resistor then connect a 300Vdc supply from VBULK
    to SMPSREF. Verify that the signal at Q606 collector is a 300V peak to peak
    square wave. The current draw should be less than 70ma.

    4. Verify that +Vcc and –Vcc are ~ 21Vdc with 300V on Vbulk.
    5. Remove the supply, check the AC fuse and verify proper operation when plugged
    into the AC line.

    Initial Field Failure Reports


    To date early field failures have been observed in the 3 categories listed below. Included in each
    category are typical warning signs indicative of each as well as corrective actions implemented.

    1. Shorted devices due to metal shaving contamination. Single shorted output device with no
    other failures. Look for metal shavings in the silpad insulator. Vtech has added an additional
    cleaning stage to remove these from the heatsink.

    2. Low IGBT gate drive at start up. Typically a catastrophic failure with extensive power
    supply gate drive damage (R625-628,Q601-606,U602-602,U608,U609) . The 15 ohm
    PTC at RT601 allows U608 to fully initialize before the supply is enabled.
    3. 230V power up failures due to a sticking relay. The dominant failure modes observed
    have been a blown fuse and/or damaged U603. Check for a stuck relay by looking across
    the contacts of K600 while unpowered for a short between 1/2VBULK and DOUBLER.
    These can be accessed topside by probing T601 Pin 6 (highlighted in pink and R611 Pin
    2 highlighted in white).

    In some cases a stuck relay can be “unstuck” by getting knocked about in shipping and
    will measure ok. It is also worth noting that the bulk caps C610 and C611 can be
    damaged due to overvoltage stress if powered on at 220-264V with a stuck relay. In this
    case the unit will power up successfully but will not work when driving a load. Replacing
    C610 and C611 will remedy this. The auto detect circuitry has been redesigned effective
    1/14/09 to prevent a power down glitch which causes the stuck relay.

    You might also like