Tool Catalogue

USE GENUINE SERVICE PARTS
Briggs & Stratton

Service Tools
Catalog
Briggs & Stratton Corporation Milwaukee, Wisconsin 53201

Printed in U.S.A. Form MS-8746-9/01
Copyright  2001 by Briggs & Stratton Corporation
All rights reserved. No part of this book may be reproduced or

transmitted, in any form or by any means, electronic or mechanical,
including photocopying, recording or by any information storage and
retrieval system, without permission in writing from Briggs & Stratton
Corporation.
TOOLS
Section Contents
Part # Page Part # Page
4185 Thread Refill 10-32 . . . . . . . . . . . . . . . . . . . . 31 @19173 Reamer – Finish . . . . . . . . . . . . . . . . . . . . . . . 6
4186 Thread Refill 1/4-20 . . . . . . . . . . . . . . . . . . . 31 @19174 Reamer – Counterbore . . . . . . . . . . . . . . . . . 6
4187 Thread Refill 5/16-18 . . . . . . . . . . . . . . . . . . 31 @19175 Reamer – Finish . . . . . . . . . . . . . . . . . . . . . . . 6
4188 Thread Refill M5x.8 . . . . . . . . . . . . . . . . . . . . 31 19178 Plug Gauge – Main Bearing . . . . . . . . . . . . . 6
4189 Thread Refill M6x1 . . . . . . . . . . . . . . . . . . . . 31 19179 Bushing Driver . . . . . . . . . . . . . . . . . . . . . . . . . 6
4190 Thread Refill M8x1.25 . . . . . . . . . . . . . . . . . 31 19182 Puller Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4191 Thread Refill 14mm Spark Plug-3/8” . . . . . 31 @19184 Tool Kit – Main Bearing . . . . . . . . . . . . . . . . . 6
4192 Thrd Refill 14mm Spk Plg-3/4” Vanguard . 31 @19186 Reamer Guide Bushing . . . . . . . . . . . . . . . . . 5
5054B Rewind Tool . . . . . . . . . . . . . . . . . . . . . . . . . . 14 19191 Reamer Guide . . . . . . . . . . . . . . . . . . . . . . . . 10
5056B Pump, Oil Evacuator . . . . . . . . . . . . . . . . . . . 14 19199 Dial Caliper . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
19055 Plug Gauge – Plunger . . . . . . . . . . . . . . . . . 14 19200 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . 11
19056 Reamer – Plunger . . . . . . . . . . . . . . . . . . . . . 14 @19201 Reamer Guide Bushing . . . . . . . . . . . . . . . . . 6
19057 Bushing Driver – Plunger . . . . . . . . . . . . . . . 14 19203 Flywheel Puller . . . . . . . . . . . . . . . . . . . . . . . 11
19058 Reamer – Plunger . . . . . . . . . . . . . . . . . . . . . 14 19204 Bushing Driver . . . . . . . . . . . . . . . . . . . . . . . . . 9
19061 Screwdriver – Carb. Jet . . . . . . . . . . . . . . . . 14 19205 Hone Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
19062 Screwdriver – Carb. Jet . . . . . . . . . . . . . . . . 14 19206 Stone Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
19063 Valve Spring Compressor . . . . . . . . . . . . . . 11 19207 Stone Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
19064 Reamer – Valve Guide . . . . . . . . . . . . . . . . . 10 19208 Stone Retainer Springs . . . . . . . . . . . . . . . . . 7
19066 Reamer – Valve Guide . . . . . . . . . . . . . . . . . 10 19209 Drive Shank . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
19069 Flywheel Puller . . . . . . . . . . . . . . . . . . . . . . . 11 19210 Stop – Hone . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
19070 Piston Ring Compressor . . . . . . . . . . . . . . . 11 19211 Hone Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
@19094 Pilot Guide Bushing . . . . . . . . . . . . . . . . . . . . 5 19212 Stone Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
@19095 Reamer – Finish . . . . . . . . . . . . . . . . . . . . . . . 5 19213 Stone Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
@19096 Pilot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5, 5 19214 Stone Carrier . . . . . . . . . . . . . . . . . . . . . . . . . . 7
@19097 Pilot Guide Bushing . . . . . . . . . . . . . . . . . . . . 5 19215 Stone Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
@19099 Reamer – Counterbore . . . . . . . . . . . . . . . . . 5 19216 Stone Springs . . . . . . . . . . . . . . . . . . . . . . . . . 7
@19101 Reamer Guide Bushing . . . . . . . . . . . . . . . . . 5 19217 Drive Shank . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
19122 Plug Gauge – Valve Guide . . . . . . . . . 10, 11 19218 Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
19123 Cylinder Support Jack . . . . . . . . . . . . . . . . . . 5 19219 Plug Gauge – Main Bearing . . . . . . . . . . . . . 8
19124 Bushing Driver . . . . . . . . . . . . . . . . . . . . . . . . . 5 19220 Pilot Guide Bushing . . . . . . . . . . . . . . . . . . . . 8
19126 Expansion Pilot . . . . . . . . . . . . . . . . . . . . . . . . 4 19222 Reamer Guide Bushing . . . . . . . . . . . . . . . . . 8
19127 Expansion Pilot . . . . . . . . . . . . . . . . . . . . . . . . 4 19223 Pilot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
@19129 Cutter Shank . . . . . . . . . . . . . . . . . . . . . . . . . . 4 19224 Reamer – Counterbore . . . . . . . . . . . . . . . . . 8
@19130 T-Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 19226 Bushing Driver . . . . . . . . . . . . . . . . . . . . . . . . . 8
19135 Knockout Pin . . . . . . . . . . . . . . . . . . . . . . . . . . 4 19227 Cylinder Support Jack . . . . . . . . . . . . . . . . . . 8
19136 Insert Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 19228 Tool Kit – Main Bearing . . . . . . . . . . . . . . . . . 8
19137 T-Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 @19229 Tang Bender . . . . . . . . . . . . . . . . . . . . . . . . . . 11
19138 Valve Seat Puller Kit . . . . . . . . . . . . . . . . . . . . 5 19230 Piston Ring Compressor . . . . . . . . . . . . . . . 11
19139 Puller Nut . . . . . . . . . . . . . . . . . . . . . . . . . 4, 13 19231 Reamer – Counterbore . . . . . . . . . . . . . . . . . 9
19140 Puller Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 19232 Repair Kit – Valve Guide . . . . . . . . . . . . . . . . 9
19141 Puller Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 19233 Reamer – Finish . . . . . . . . . . . . . . . . . . . . . . . 9
19151 Plug Gauge – Valve Guide . . . . . . . . . . . 9, 11 19234 Reamer Guide . . . . . . . . . . . . . . . . . . . . . . . . . 9
@19158 Tool Kit – Main Bearing . . . . . . . . . . . . . . . . . 4 19237 Valve Seat Cutter Kit . . . . . . . . . . . . . . . . . . . 9
19164 Plug Gauge – Cam Bearing . . . . . . . . . . . . 14 19238 Puller Bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
19165 Flywheel Puller . . . . . . . . . . . . . . . . . . . . . . . 11 19239 Puller Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
19166 Plug Gauge – Main Bearing . . . . . . . . . . . . . 5 19240 Puller Washer . . . . . . . . . . . . . . . . . . . . . . . . . 9
19167 Flywheel Holder . . . . . . . . . . . . . . . . . . . . . . . 11 19244 Clutch Wrench . . . . . . . . . . . . . . . . . . . . . . . . 11
@19169 Pilot Guide Bushing . . . . . . . . . . . . . . . . . . . . 6 19245 Tap Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
@19170 Reamer Guide Bushing . . . . . . . . . . . . . . . . . 6 19256 Brake Adjustment Gauge . . . . . . . . . . . . . . . 11
@19171 Reamer Guide Bushing . . . . . . . . . . . . . . . . . 6 19258 Valve Lapper . . . . . . . . . . . . . . . . . . . . . . . . . 11
@ Subject to remaining factory inventory
1
Section Contents, Cont.
Part # Page Part # Page
@19260 Trip Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 19395 Pilot Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
19263 Screwdriver – Carb. Adjustment . . . . . . . . . 11 19396 Pilot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
19264 Tap – 9 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 19397 Adapter/Driver . . . . . . . . . . . . . . . . . . . . . . . . 13
19266 Suction Cup . . . . . . . . . . . . . . . . . . . . . . . . . . 11 19398 Puller Stud . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
@19267 Suction Cup . . . . . . . . . . . . . . . . . . . . . . . . . . 11 19400 Spark Tester 3/LC Engines . . . . . . . . . . . . . 19
19268 Suction Cup . . . . . . . . . . . . . . . . . . . . . . . . . . 11 19401 Bearing Driver . . . . . . . . . . . . . . . . . . . . . . . . 13
19269 Repair Kit – Valve Guide . . . . . . . . . . . . . . . 10 19404 Telescoping Gauge . . . . . . . . . . . . . . . . . . . . 19
19270 Puller Washer . . . . . . . . . . . . . . . . . . . . . . . . 10 19406 Puller Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
19271 Puller Bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 19407 Ball Bearing Tool Kit . . . . . . . . . . . . . . . . . . . 13
19272 Puller Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 19408 Puller Stand Off . . . . . . . . . . . . . . . . . . . . . . . 13
19273 Tap – 7 mm . . . . . . . . . . . . . . . . . . . . . . . . . . 10 19416 Driver, Valve Guide . . . . . . . . . . . . . . . . . . . . 20
@19278 Test Plug Adapter . . . . . . . . . . . . . . . . . . . . . 14 19417 Valve Spring Compressor . . . . . . . . . . . . . . 20
19280 Screwdriver – Carb. Jet . . . . . . . . . . . . . . . . 11 19418 Flywheel Holder . . . . . . . . . . . . . . . . . . . . . . . 20
@19281 Reamer – Counterbore . . . . . . . . . . . . . . . . . 6 19419 Piston Pin Fixture . . . . . . . . . . . . . . . . . . . . . 20
@19282 Reamer Guide Bushing . . . . . . . . . . . . . . . . . 6 19420 Puller, Crankshaft Pulley . . . . . . . . . . . . . . . 21
19300 Tool Kit – Basic . . . . . . . . . . . . . . . . . . . . . . . 11 19421 Puller, Camshaft Bearing . . . . . . . . . . . . . . . 21
19302 Valve Seat Cutter Repair Kit . . . . . . . . . . . . . 9 19422 Driver, Camshaft Bearing . . . . . . . . . . . . . . . 21
19303 Stone Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 19423 Driver, Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
19304 Stone Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 19424 Driver, Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
19305 Screwdriver – Offset . . . . . . . . . . . . . . . . . . . 15 19433 Flywheel Strap Wrench . . . . . . . . . . . . . . . . 22
19310 Flywheel Holder . . . . . . . . . . . . . . . . . . . . . . . 15 19434 Ft. Pound Torque Wrench . . . . . . . . . . . . . . 22
19318 Puller Bolt . . . . . . . . . . . . . . . . . . . . . . . . 12, 13 19435 C-Ring Installation Tool . . . . . . . . . . . . . . . . 22
19319 Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 @19436 C-Ring Removal Tool . . . . . . . . . . . . . . . . . . 22
19320 Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 13 19440 Support Driver . . . . . . . . . . . . . . . . . . . . . . . . 13
19332 Tool Kit – 2 Cycle . . . . . . . . . . . . . . . . . . . . . 12 19441 Dial Indicator . . . . . . . . . . . . . . . . . . . . . . . . . 22
19333 Reamer – Governor Bushing . . . . . . . . . . . 16 19442 Torqux Star Bits . . . . . . . . . . . . . . . . . . . . . . . 23
19340 Ring Expander . . . . . . . . . . . . . . . . . . . . . . . . 16 19443 Compression Test Adaptor . . . . . . . . . . . . . 23
19343 Valve Seat Cutter Kit . . . . . . . . . . . . . . . . . . 12 19444 Valve Guide Reamer . . . . . . . . . . . . . . . . . . 23
19344 Roll Pin Driver . . . . . . . . . . . . . . . . . . . . . . . . 16 19445 Torx Driver . . . . . . . . . . . . . . . . . . . . . . . . . . 23
19345 Reamer Guide . . . . . . . . . . . . . . . . . . . . . . . . 16 19446 Valve Seat Cutter Kit . . . . . . . . . . . . . . . . . . 23
19346 Reamer – Valve Guide . . . . . . . . . . . . . . . . . 16 @19447 Replacement Drive Pins . . . . . . . . . . . . . . . 22
19347 Valve Spring Compressor . . . . . . . . . . . . . . 16 19448 Replacement Strap . . . . . . . . . . . . . . . . . . . . 22
19349 Bearing Driver . . . . . . . . . . . . . . . . . . . . . . . . 16 19449 Replacement Fuse . . . . . . . . . . . . . . . . . . . . 25
19350 Bearing Driver . . . . . . . . . . . . . . . . . . . . . . . . 17 19450 Bearing Driver . . . . . . . . . . . . . . . . . . . . . . . . 24
19351 Cylinder Support . . . . . . . . . . . . . . . . . . . . . . 17 19454 Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
@19352 Tang Bender . . . . . . . . . . . . . . . . . . . . . . . . . . 17 19455 Torx Socket . . . . . . . . . . . . . . . . . . . . . . . . . 24
19353 Universal Socket . . . . . . . . . . . . . . . . . . . . . . 17 19456 Tachometer Adapter . . . . . . . . . . . . . . . . . . . 24
19367 Bushing Driver – Valve Guide . . . . . . . . . . . 10 19457 Diesel Tachometer . . . . . . . . . . . . . . . . . . . . 24
19368 Ignition Tester, Standard Engines . . . . . . . . 11 19458 14 MM Socket . . . . . . . . . . . . . . . . . . . . . . . . 24
@19373 Pilot Guide Bushing . . . . . . . . . . . . . . . . . . . . 4 19459 16 MM Socket . . . . . . . . . . . . . . . . . . . . . . . . 24
19374S Spark Plug Wrench . . . . . . . . . . . . . . . . . . . . 17 19460 Carburetor Socket Set . . . . . . . . . . . . . . . . . 24
19375 Plug Gauge – Main Bearing . . . . . . . . . . . . 17 19461 Primer Bulb Removal Tool . . . . . . . . . . . . . . 24
19377 Plug Gauge – Main Bearing . . . . . . . . . . . . 17 19462 Primer Bulb Installation Tool . . . . . . . . . . . . 25
19378 Plug Gauge – Main Bearing . . . . . . . . . . . . 18 19463 Transducer . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
19380 Plug Gauge – Main Bearing . . . . . . . . . . . . 18 19464 Digital Multimeter . . . . . . . . . . . . . . . . . . . . . 25
19381 Plug Gauge – Valve Guide . . . . . . . . . . . . . 18 19465 Valve Adjustment Set . . . . . . . . . . . . . . . . . . 25
19382 Plug Gauge – Valve Guide . . . . . . . . . . . . . 18 19467 Starter Ring Removal/Installation Tool . . . 25
19383 Plug Gauge – Cam Bearing . . . . . . . . . . . . 18 19468 DC Shunt . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
19384 Plug Gauge – Cam Bearing . . . . . . . . . . . . 18 19475 Leakdown Tester . . . . . . . . . . . . . . . . . . . . . . 20
19385 Adjustment Gauge . . . . . . . . . . . . . . . . . . . . 18 19478 Orifice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
19386 Plug Gauge – Cam Bearing . . . . . . . . . . . . 18 19480 Tang Bender . . . . . . . . . . . . . . . . . . . . . . . . . . 26
19387 Plug Gauge – Cam Bearing . . . . . . . . . . . . 19 19482 Individual Torqux Driver . . . . . . . . . . . . . . . . 29
19389 Tachometer/Hourmeter . . . . . . . . . . . . . . . . 19 19485 Telescoping Gauge . . . . . . . . . . . . . . . . . . . . 26
19391 Screwdriver – Offset . . . . . . . . . . . . . . . . . . . 19 19487 Dial Bore Gauge . . . . . . . . . . . . . . . . . . . . . . 27
19393 Torque Wrench . . . . . . . . . . . . . . . . . . . . . . . 19 19489 Flywheel Holder . . . . . . . . . . . . . . . . . . . . . . . 27
19394 Support Driver . . . . . . . . . . . . . . . . . . . . . . . . 13 19491 Alternator Wrench . . . . . . . . . . . . . . . . . . . . . 27
2
Section Contents, Cont.
Part # Page
19493 Mity Vac Pressure/Vacuum Pump . . . . . . . 28
19495 Digital Crankcase Vacuum Tester . . . . . . . 28
19497 Universal Socket . . . . . . . . . . . . . . . . . . . . . . 28
19499 AC/DC Current Clamp . . . . . . . . . . . . . . . . . 29
19510 Individual Torqux Driver . . . . . . . . . . . . . . . . 29
19518 Torx Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
19552 C-Ring Removal Tool . . . . . . . . . . . . . . . . . . 30
89838 Spark Plug Wrench . . . . . . . . . . . . . . . . . . . . 30
93963 Valve Guide Lubricant . . . . . . . . . . . . . . . . . 11
94150 Valve Lapping Compound . . . . . . . . . . . . . . 11
94814 Puller Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
100007 Thread Repair Kit 10-32 . . . . . . . . . . . . . . . . 31
100008 Thread Repair Kit 1/4-20 . . . . . . . . . . . . . . . 31
100009 Thread Repair Kit 5/16-18 . . . . . . . . . . . . . . 31
100010 Thread Repair Kit M5x.8 . . . . . . . . . . . . . . . 31
100011 Thread Repair Kit M6x1 . . . . . . . . . . . . . . . . 31
100012 Thread Repair Kit M8x1.25 . . . . . . . . . . . . . 31
100013 Thread Repair Kit M14x1.25 Spark Plug . . 31
100022 Silencio Hearing Protectors . . . . . . . . . . . . . 30
100023 Alcohol Tester . . . . . . . . . . . . . . . . . . . . . . . . 30
100024 Thread Repair Kit – Master . . . . . . . . . . . . . 31
100054 Heavy Duty Shop Towels . . . . . . . . . . . . . . . 30
225136 Washer . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 13
271400 Spray Paint . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
271401 Spray Paint . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
271402 Spray Paint . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
271403 Spray Paint . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
271404 Spray Paint . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
271405 Spray Paint . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
271675 Spray Paint . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Service Tips & Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3
19138 VALVE SEAT PULLER KIT
KIT INCLUDES:
19139 Puller Nut
19140 Puller Nut
19141 Puller Nut
19182 Puller Nut 19139 19140 19141 19182
*Not available
separately
*
NOTE: Each tool part number can also be ordered separately.
VALVE SEAT INSERT AND COUNTERBORE TOOLS
19126
19127
@19129
19135 19136 19137

@19130
COUNTERBORE TOOLS USED ON CAST IRON ENGINE MODELS

5, 6, N, 8, 9, 14, 19, 20, 23, 240000, 300000, 320000
ORDER THESE TOOL PART NUMBERS SEPARATELY:

19126 Expansion Pilot – 1/4” Valve Guide 19135 Knockout Pin
19127 Expansion Pilot – 5/16” Valve Guide 19136 Insert Driver
19129 Cutter Shank 19137 T-Handle For Pilots
19130 T-Handle For Cutter Shank
4
@19158 MAIN BEARING TOOL KIT
ENGINE MODELS 6, 8, 6B, 8B, N, 90000, 100700*, 110000, 120000,* 130000*
*Mag. Side Only
@19096
@19094 @19095 @19097 @19099
@19101 19123
19166 @19186 19124 @19373
KIT INCLUDES:
@19094 Pilot Guide Bushing 19123 Cylinder Support Jack
@19095 Reamer – Finish 19124 Bushing Driver
@19096 Pilot 19166 Plug Gauge
@19097 Pilot Guide Bushing @19186 Reamer Guide Bushing
@19099 Reamer – Counterbore @19373 Pilot Guide Bushing
@19101 Reamer Guide Bushing
5
@19184 MAIN BEARING TOOL KIT
INSTALLING STEEL BACKED ALUMINUM BEARINGS IN ENGINE MODELS
130000*, 140000, 170000, 171000, 190000, 191000
*PTO Side Only
@19096
@19169 @19170 @19171
@19201 @19173 @19174 @19175
19178 19179
KIT INCLUDES:
@19096 Pilot @19174 Reamer – Counterbore
@19169 Pilot Guide Bushing @19175 Reamer – Finish
@19170 Reamer Guide Bushing 19178 Plug Gauge
@19171 Reamer Guide Bushing 19179 Bushing Driver
@19173 Reamer – Finish @19201 Reamer Guide Bushing

MAIN BEARING TOOLS
For installing DU bearing in PTO bearing:
Horizontal Crankshaft Engine Models
140000, 170000, 190000
For installing DU bearing in MAG. bearing:
Vertical Crankshaft Engine Models
171000, 191000
@19281 Reamer – Counterbore
@19282 Reamer Guide Bushing “MAGNETO”
Use with 19096 pilot, 19179 bushing driver and 19227
@19281 @19282 cylinder support.
6
19205 AMMCO HONE SET FOR ALUMINUM BORE ENGINES
19206
19207 19208 19209 19210

SET INCLUDES:
19206 Stone Set, 320 Grit, Range 1-7/8” to 2-3/4” 19208 Stone Retainer Springs
(47.6 mm to 69.9 mm) 19209 Drive Shank
For aluminum bore engines 19210 Stop
19207 Stone Set, 320 Grit, Range 2-3/4” to 3-5/8”
(69.8 mm to 92.0 mm)
For aluminum bore engines
*Not Available Separately NOTE: Each tool part number can also be ordered separately.
19211 AMMCO HONE SET FOR CAST IRON BORE/SLEEVE ENGINES
19217
19218
19212 19214
19213 19215 19216

*
SET INCLUDES:
19212 Stone Set, 60 Grit for cast iron 19215 Stone Carrier, Range 3-5/16” to 4-1/8”
bore/sleeve engines (84.1 mm to 104.8 mm)
19213 Stone Set, 220 Grit for cast iron 19216 Stone Retainer Springs
bore/sleeve engines 19217 Drive Shank
19214 Stone Carrier, Range 2-1/2” to 3-5/16” 19218 Extension
(63.5 mm to 84.1 mm)
*Not Available Separately NOTE: Each tool part number can also be ordered separately.
7
19228 MAIN BEARING TOOL KIT
FOR SERVICING ENGINE MODELS 220000, 250000, 280000, 400000, 420000
19223
19219 19220 19222 19224
19226 19227
KIT INCLUDES:
19219 Plug Gauge 19224 Reamer – Counterbore

19220 Pilot Guide Bushing 19226 Bushing Driver
19222 Reamer Guide Bushing 19227 Cylinder Support Jack
19223 Pilot
8
19232 VALVE GUIDE REPAIR KIT
FOR SERVICING 5/16” VALVE GUIDES
19234
19239
NUT
19240
19151 19233 19204 19231 19238 19264
KIT INCLUDES:
19151 Plug Gauge 19238 Puller Bolt
19204 Bushing Driver 19239 Nut
19231 Reamer – Counterbore 19240 Washer
19233 Reamer – Finish 19264 9 mm Tap
19234 Reamer Guide
19237 NEWAY VALVE SEAT

CUTTER KIT
For reconditioning 30° and 45° angle valve seats.
NOTE: For replacement tungsten carbide blade set,
specify part number 19302. Set includes:
• 3 blades – use on either side of cutter head
• 3 set screws
• 3 wedges
19302
Replace blades in sets only.
9
19269 VALVE GUIDE REPAIR KIT
FOR SERVICING 1/4” VALVE GUIDES
19191 19271
19064 19066 19122 19270 19272 19273 19367
KIT INCLUDES:
19064 Reamer – Counterbore 19271 Puller Bolt
19066 Reamer – Finish 19272 Nut
19122 Plug Gauge 19273 7 mm Tap
19191 Reamer Guide 19367 Bushing Driver
19270 Washer
10
19300 BASIC TOOL KIT
19063 19069 19070 19122 19151
19165 19167 19203 19200
@19229
19258
19263 19230 19244 19256 19266 19268
19280 19368 93963 94150 MS-8746
KIT INCLUDES:
19063 Valve Spring Compressor 19244 Starter Clutch Wrench
19069 Flywheel Puller 19256 Brake Adjustment Gauge
19070 Piston Ring Compressor (5 HP and below) 19258 Valve Lapper* (includes 19266 and
19122 Plug Gauge – 1/4” Valve Guide 19268)
19151 Plug Gauge – 5/16” Valve Guide 19263 Screwdriver – Carburetor Adjustment
19165 Flywheel Puller 19280 Screwdriver – Carburetor Jet – (4 Bladed)
19167 Flywheel Holder 19368 Tester – Ignition
19203 Flywheel Puller 93963 Lubricant – Valve
19200 Tachometer 94150 Valve Lapping Compound
@19229 Tang Bender MS-8746 Tool Catalog
19230 Piston Ring Compressor (above 5 HP)
*To order replacement suction cups, specify: 19266 – 3/4” (19.1 mm)
@19267 – 1” (25.4 mm)
19268 – 1-1/4” (31.8 mm)
11
19303 STONE SET 19304 STONE SET
60 grit, range 1-7/8” to 2-3/4” (47.6 mm to 69.9 mm). 220 grit, range 1-7/8” to 2-3/4” (47.6 mm to 69.9 mm).
Use with 19205 hone set see page 7 for cast iron Use with 19205 hone set see page 7 for cast iron
bore/sleeve engines. bore/sleeve engines.
19332 2-CYCLE TOOL KIT

FOR SERVICING ENGINE MODELS 95700, 96700
PLAIN WASHER
*WASHER *BUSHING *BUSHING
225136 19319 19320
HEX NUT
PULLER STUD
PULLER
PLATE PULLER STUD STAND OFF *PULLER
BOLT 19318
*Part numbers, 225136, 19318, 19319 and 19320 can be ordered individually. All other parts are not available individually
and must be ordered as a kit.
19343 VALVE SEAT CUTTER KIT

For use on Quantum and Vanguard OHV engines.
Includes 6 mm pilot for Vanguard engines.
12
19407 MAIN BEARING TOOL KIT
FOR SERVICING ENGINE MODELS 85400, 115400, 185400, 245400
19318 PULLER SCREW

19395 PILOT
NUT 19397 ADAPTER/DRIVER
19398 PULLER STUD
19396 PILOT
19454 SUPPORT
19408 PULLER STAND OFF
19320 DRIVER 19401 DRIVER
19139 PULLER 19406 PULLER

NUT NUT
19394 SUPPORT 19440 SUPPORT 94814 NUT 225136 WASHER

DRIVER DRIVER
KIT INCLUDES:
19139 Puller Nut 19398 Puller Stud
19318 Puller Screw 19401 Driver
19454 Support 19406 Puller Nut
19320 Driver 19408 Puller Stand Off
19394 Support Driver 19440 Support Driver
19395 Pilot Nut 94814 Nut
19396 Pilot 225136 Washer
19397 Adapter/Driver
13
INDIVIDUAL TOOLS
5054B Rewind Tool

For replacing rewind spring and starter ropes.
For use on engines equipped with ratchet style starter
clutches.
5056 B Pump, Oil Evacuator

Handy tool for draining oil from engines with restricted
access. Use with an electric drill. Inlet and outlet hose
included.
Breaker Point Plunger Hole Servicing

19055 Servicing breaker point plunger hole – order separately:
• 19055 Plug Gauge
19056
• 19056 Reamer – Counterbore
• 19057 Bushing Driver
19057
• 19058 Reamer – Finish
19058
Screwdrivers – Carburetor Jet

For removing most carburetor jets.
19061 • 19061 Screwdriver
• 19062 Screwdriver
19062
19164 Cam Bearing Plug Gauge

For checking cam gear bearings for wear –
most engine models.
14
19199 Dial Caliper
Range: 0” to 6”
(0 to 152.4 mm)
19245 Carburetor Tap Set

For cleaning threads in 2 piece flo-jet carburetor.
• 5/16”-32 NEF
• 1/4”-32 NEF
@19260 Trip Cord and Switch

Replacement parts for Blade Monitor
@19278 Test Plug Adapter

Test plug adapter serves as a convenient connector for
HI-POT testing 120 volt electric motor.
IMPORTANT: Refer to Electric Motor Service and
Repair Instructions manual, MS-8247, for detailed
HI-POT testing procedures.
19305 Carburetor Offset Screwdriver

For removing carburetor from 3 HP and 5 HP horizontal
crankshaft engines.
Offset feature allows access to lower carburetor
mounting screw for quick removal.
19310 Flywheel Holder

For holding flywheel on Quantum engine Model
Series 100700.
15
19333 Governor Bushing Reamer
For finish reaming 1/4” (6.35 mm) governor shaft
bushing, after installation.
3 HP to 16 HP single cylinder mechanical governor
engines.
19340 Ring Expander

For removing and installing piston rings. Minimizes
ring distortion and breakage. All engine models.
19344 Roll Pin Driver

For installing roll pin in magneto main bearing on
V-Twin Vanguard engines.
19345 Reamer Guide

For guiding the 19346 reamer while finish reaming
valve guide bushing in Vanguard engines.
19346 Valve Guide Reamer

For finish reaming single cylinder Vanguard engine
Models 104700, 161400, 260700, 261700 valve guide
bushing after installation.
19347 Valve Spring Compressor

For compressing valve springs, most Vanguard
engine models.
19349 Bearing Driver

For replacing magneto side main bearing on V-Twin
Vanguard engines built before 97050100
Use with 19227 Cylinder Support Tool.
16
For replacing magneto side main bearing on
Vanguard engine Model 161400.
19351 Cylinder Support

For replacing magneto side main bearing on
Vanguard engine Model 161400.
@19352 Tang Bender

For all V-Twin Vanguard engines. Used for setting top
no load and governed idle engine speed.
19353 Universal Socket

13 mm, 12 point, 1/4” Drive. For removing electric starter
mounting screws. All V-Twin Vanguard engines.
19374S Spark Plug Wrench

For removing 5/8” and 13/16” hex head spark plugs.
19375 Main Bearing Plug Gauge

For checking sump bearing for wear – engine Models
97700, 99700, 100700, 120000.

Checking magneto bearing for wear – Vanguard
engine Model 161400.
17
Checking magneto and PTO bearing for wear –
Vanguard engine Models 260700, 261700.

Checking magneto and PTO bearing for wear – V-Twin
Vanguard engines.
19381 Valve Guide Plug Gauge

Checking valve guides for wear – Vanguard engine
Models 104700, 161400, 260700, 261700 and single
cylinder OHV Model 280000.
19382 Valve Guide Plug Gauge

Checking valve guides for wear – V-Twin Vanguard
engines. Also, single cylinder Vanguard engine Models
85400, 115400, 185400, 235400 and 245400.

Checking cam gear bearings for wear – Vanguard
engine Models 161400, 260700, 261700.

Checking cam gear bearing for wear – Mag. side
19385 Adjustment Gauge

For adjusting secondary governor spring.

Checking cam gear bearing for wear – PTO side
18
For checking cam gear bearings for wear. Engine
Models 97700, 99700.
19389 Digital Tachometer & Hourmeter

Meter displays RPM while engine is running. When
engine is stopped, meter displays elapsed time.
19391 Carburetor Offset Screwdriver

For removing carburetor from 3 HP and 5 HP horizontal
crankshaft engines with Torx mounting screws.
Offset feature allows access to carburetor mounting
screw for quick removal.
19393 Torque Wrench

Range: 0 to 300 Inch Pound
(0 to 346.8 Kgcm)
(0 to 34.0 Nm)
19400 Spark Tester

Special Air Gap of .400” (10 mm) for use on
Vanguard 3 Cylinder Liquid Cooled Engines.
19404 Telescoping Gauge

Range: 2” to 3-1/2”
(50.8 to 88.9 mm)
19
19475 Leakdown Tester
Used to test the sealing capabilities of the compression
components of all engines. Comes with crankshaft
clamp.
19416 Valve Guide Driver

For installing valve guide bushings on Vanguard
3 cylinder liquid cooled engines.
19417 Valve Spring Compressor

For removing and installing valves on Vanguard

For removing and installing flywheel on Vanguard
19419 Piston Pin Fixture

For removing and installing piston pin on Vanguard 3
cylinder liquid cooled gasoline engines.
20
19420 Puller, Crankshaft Pulley
For removing crankshaft pulley on Vanguard 3 cylinder
liquid cooled engines.
19421 Puller, Camshaft Bearing

For removing camshaft bearing on Vanguard 3 cylinder
19422 Driver, Camshaft Bearing

For installing camshaft bearing on Vanguard 3 cylinder
19423 Driver, Oil Seal

For installing timing gear cover oil seal on Vanguard
19424 Driver, Oil Seal

For installing rear oil seal on Vanguard 3 cylinder
21
19433 Flywheel Strap Wrench
For holding flywheel while removing and torquing
flywheel nut. All engine models.
NOTE: Replacement strap is available separately.
Order Part #19448.
@19434 Foot Pound Torque Wrench

Adjustable click type with ratchet
0-150 Ft. Lbs.
19435 C-Ring Installation Tool

Installing new C-ring on starter motor when replacing
starter motor drive.
@19436 C-Ring Removal Tool

For removing C-ring on starter motor when replacing
NOTE: Replacement drive pins available separately.
@Order part #19447.
19441 Dial Indicator

For timing injector pump on Vanguard 3 cylinder liquid
cooled diesel engines.
22
19442 Torqux Star Bits
To remove and install Torx screws. In handy pouch.
T-10, T-15, T-20, T-25, T-27, T-30, T-40, T-45
Bit length 3.75 inches.
19443 Compression Test Adaptor

For testing compression on Vanguard 3 cylinder
liquid cooled diesel engines.
19444 Valve Guide Reamer

For finish reaming Vanguard V-Twin valve guides
after installation. Also used for cleaning valve guides
on Vanguard three cylinder liquid cooled engines.
Use with 19345 Reamer Guide.
19445 Torx Driver

For installing tamper proof screws in governor paddle –
Vanguard 3 cylinder liquid cooled gasoline engines.
19446 Neway Valve Seat Cutter Kit

For reconditioning 30° and 45° angle valve seats on
Vanguard 3 cylinder liquid cooled engines.
Includes 15° cutter for top cutting 30° angle seats.
Includes 6.0 and 6.02 mm pilots.
23
For replacing magneto side main bearing on V-Twin
Vanguard engines built after 97043000.
19455 Torx Socket

Remove and install carburetor mounting studs on
Intek V-Twins.
19456 Tachometer Adaptor

When attached to ignition module, permits use of
Digital Tachometer, 19389 on Vanguard 3 cylinder
liquid cooled gasoline engines.
19457 Digital Tachometer & Hourmeter

For use on Vanguard 3 cylinder liquid cooled diesel
engines with 6mm diameter fuel lines.
19460 Carburetor Socket Set

Remove and install main jet housing on Intek
V-Twins.
Sockets may also be ordered separately
19458 – 14 mm
19459 – 16 mm
19461 Primer Bulb Removal Tool

For quick and easy removal of primer bulb and retainer
on engines equipped with primer bulb system.
24
19462 Primer Bulb Installation Tool
Installs new primer bulb and retainer in a ‘‘snap”.
19463 Quick Clamp Transducer

Use with 19457 Digital Tachometer and hourmeter.
Quick clamp design with spring loaded post terminal
for easy installation and removal.
19464 Digital Multimeter

Use for diagnosing and testing electrical, charging and
starting systems.
Meter Features:
Volts Scale: 0 to 750 AC
0 to 1000 DC
Ohms Scale: 0 to 320,000,000
Amperage – AC, DC 0 to 10 Continuous
0 to 20 for 30 Seconds
Audible Diode Test
Audible Continuity Test
Auto Ranging
Replacement Fuse: Order Part No. 19449
19465 Valve Adjustment Set

For adjusting valves on Vanguard and Intek V-Twin
engines. Offset 13 mm wrench with 5 mm hex and T-40
torx drivers.
@19467 Starter Ring Removal /

Installation Tool
For removing and installing “C” rings on steel pinion
starter drives with rubber dust cover.
25
19468 DC AMP Shunt
An improved version of a valuable diagnostic tool.
Color coded receptacles hold digital multimeter leads
securely while testing. This tool works with any digital
multimeter with a milivolt scale.
19478 Orifice
Calibrated specifically for use with 19475 Leakdown
Tester on 3 L/C engines.
19480 Tang Bender

For all engines. Used for setting top no load and
governed idle speeds.
19485 Telescoping Gauge

Twelve inch (304 mm) length handle will reach the
bottom of any cylinder bore.
Range: 2 in. – 3 1/2 in. (51 – 81 mm).
26
19487 Dial Bore Gauge
Fast, accurate method of checking cylinder bore size,
taper and out of round.
Range: 1.960 – 6.185 in.

For use on engines equipped with fan retainer.
280000 & 310000 single cylinder engines
V-Twin Vanguard
Opposed Twin
V-Twin Intek
19491 Alternator Wrench

For use on 3 L/C engines. Holds alternator pulley nut
when removing and installing alternator pulley.
Also handy when rotating crankshaft when adjusting
valve clearance.
27
19493 Mity Vac Pressure/Vacuum Pump
Check carburetor inlet needles and seats for leakage.
Check pressure switches.
Check dash pot pull off on 3 L/C choke.
19495 Digital Crankcase Vacuum Tester

Extremely accurate and simple tool for measuring
crankcase vacuum.
Modify an old dipstick or oil fill plug by installing a
barbed connector and attach the hose from the gauge.
Check crankcase vacuum with engine running at top
no load speed.
19497 Universal Socket

12 mm 6 point socket for removing and installing start-
er motors on current Vanguard V-Twin Engines, and
3 L/C diesel injection pumps.
28
19499 AC/DC Current Clamp
Use with 19464 Digital Multimeter.
A quick alternative to the DC shunt for checking
charging out put and starter motor current draw.
Individual Torqux Drivers

Individual Torqux replacement bits
19503 – T-10 19506 – T-27
19504 – T-15 19507 – T-30
19505 – T-20 19508 – T-40
19483 – T-25 19509 – T-45
19518 Torx Driver

For removing and installing tamper proof screw used
on Touch ‘‘N” Mow starters.
29
19552 C-Ring Removal Tool
For removing C-ring on starter motor when replacing
All models.
Replaces 19436
89838 Spark Plug Wrench

For removing 13/16” and 3/4” hex head spark plugs.
100022 Advanced Hearing Protectors

Advanced hearing protector reduces dangerous high
frequency noise levels. Wear when operating
equipment for extended time periods.
Noise Reduction Rating
Behind the Head Position 23 decibels
Under the Chin Position 24 decibels
Over the Head Position 25 decibels
The range of noise reduction ratings for existing
hearing protectors is approximately 0 to 30. (High
numbers denote greater effectiveness.)
100023 Alcohol Tester

Use to determine the alcohol content in gasoline.
100054 Heavy Duty Shop Towels
30
Fix-A-Thread Kits
For repairing damaged and stripped threads.
100024 – Thread Repair Kit Master
* 100007 – Thread Repair Kit 10-32
* 100008 – Thread Repair Kit 1/4-20
* 100009 – Thread Repair Kit 5/16-18
100010 – Thread Repair Kit M5x.8
100011 – Thread Repair Kit M6x1
100012 – Thread Repair Kit M8x1.25
* 100013 – Thread Repair Kit 14 mm Spark Plug
*Included in 100024 Master Kit
Thread Insert Refills
4185 – 10-32 Refill
4186 – 1/4-20 Refill
4187 – 5/16-18 Refill
4188 – M5x.8 Refill
4189 – M6x1 Refill
4190 – M8x1.25 Refill
4191 – 14 mm Spark Plug-3/8”
4192 – 14 mm Spark Plug-3/4” (Vanguard)
Aerosol Spray Paint

Fast drying, lacquer base, and gasoline resistant
13 ounce (369g) spray can
Available colors, order separately:
271400 – Gloss Black
271401 – Pearl White
271402 – Ice White
271403 – Satin Black
271404 – Industrial Gray
271405 – Pewter Mist
271675 – American Red
31
SERVICE TIPS AND TOOLS
Order the “Service Tips And Tools” booklet for additional handy service tips and tool information. This booklet is a collection of the
best tips and suggestions submitted by dealers and technicians throughout the world. Who knows, you may have an idea or
suggestion that you would like to share. The booklet is available for $1.00. Order CE8006 from the address shown below.
The Briggs & Stratton Customer Education Department has actively solicited our dealer network for their favorite service tips and
tools for a number of years. This booklet, “Service Tips and Tools” is a collection of the best. As dealers try these tips and tools, we
invariably hear the comment, “I don’t know how I got along without it”. Time is money. A tip or tool that saves time and frustration is
worth its weight in gold.
uuu
To those of you who have sent in a tip or a tool, a hearty thank you! Not just from Briggs & Stratton, but from the thousands of
dealers who benefited as well. To those of you who haven’t gotten around to it yet, send them in!
uuu
If you have a service tip or special tool that makes your life easier, describe it on a postcard and send it to the address below. If
possible, send a sample of the tool, photo and/or drawing as well. If we publish your tip or tool, we will send you a handsome Briggs
& Stratton jacket and hat. Be sure to include your full name, address and company you work for.
uuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuu
(Please type or print clearly)
YOUR NAME
COMPANY NAME
Stamp
ADDRESS
CITY, STATE, ZIP
BRIGGS & STRATTON CORPORATION

ATTN CUSTOMER EDUCATION DEPARTMENT
PO BOX 702
MILWAUKEE WI 53201-0702
32
SMALL ENGINE CARE & REPAIR BOOK
For the novice – a step-by-step guide to small engine care and repair.
The full color book is 128 pages and includes over 300 color photos and
easy-to-follow instructions. Concepts are introduced that apply to virtually
every small engine making this appealing to a very broad audience. It
offers consumers a step-by-step guide for saving money through
preventive maintenance and do-it-yourself repair. Includes a
troubleshooting section to easily diagnose common small engine
problems. Features Introductory projects that require no prior knowledge,
as well as advanced projects for the experienced repair person. Utilizes
the Briggs & Stratton name which is recognized worldwide as the small
engine leader.
Part # 274041
ANTIQUE REPAIR MANUAL

A must for the collector and old engine enthusiast. Covers repair
procedures and specifications for all Briggs & Stratton cast iron and
aluminum engines manufactured from 1919 to 1981.
Part # CE8069
SMALL ENGINES TEXTBOOK

Recently released by American Technical Publications of Homewood,
Illinois, the Briggs & Stratton written textbook, Small Engines, is already
destined to become the definitive work within the industry. This
comprehensive hardbound volume boasts 322 pages and 321
illustrations.
All OEM engine manufacturers produce repair manuals which supply the
“how-to” of most repair jobs. Few industry or outside publications provide
much in the way of “why.” Small Engines concentrates on the theory of
operation relating to all major engine systems. Both air cooled and water
cooled engines are covered.
Small Engines is supported by a Student Workbook CE8021 containing
review questions on three different levels addressing the skills and
acquired knowledge of beginners, intermediate students and those with
advanced abilities.
Part # CE8020
33
USE GENUINE SERVICE PARTS
Briggs & Stratton
Service Tools
Catalog
Briggs & Stratton Corporation Milwaukee, Wisconsin 53201

Printed in U.S.A. Form MS-8746-9/01

Tool Catalogue

Uploaded by

Copyright:

Available Formats

Tool Catalogue

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Tool Catalogue

Uploaded by

Copyright:

Available Formats

USE GENUINE SERVICE PARTS

Briggs & Stratton

Briggs & Stratton Corporation Milwaukee, Wisconsin 53201

All rights reserved. No part of this book may be reproduced or

VALVE SEAT INSERT AND COUNTERBORE TOOLS

19135 19136 19137

COUNTERBORE TOOLS USED ON CAST IRON ENGINE MODELS

ORDER THESE TOOL PART NUMBERS SEPARATELY:

@ Subject to remaining factory inventory

*Mag. Side Only

@19094 @19095 @19097 @19099

19166 @19186 19124 @19373

NOTE: Each tool part number can also be ordered separately.

@ Subject to remaining factory inventory

@19169 @19170 @19171

@19201 @19173 @19174 @19175

NOTE: Each tool part number can also be ordered separately.

@ Subject to remaining factory inventory

19207 19208 19209 19210

19213 19215 19216

19219 19220 19222 19224

19219 Plug Gauge 19224 Reamer – Counterbore

NOTE: Each tool part number can also be ordered separately.

19151 19233 19204 19231 19238 19264

19237 NEWAY VALVE SEAT

19064 19066 19122 19270 19272 19273 19367

NOTE: Each tool part number can also be ordered separately.

19063 19069 19070 19122 19151

19165 19167 19203 19200

19263 19230 19244 19256 19266 19268

19280 19368 93963 94150 MS-8746

@ Subject to remaining factory inventory

19332 2-CYCLE TOOL KIT

19343 VALVE SEAT CUTTER KIT

19318 PULLER SCREW

19398 PULLER STUD

19408 PULLER STAND OFF

19320 DRIVER 19401 DRIVER

19139 PULLER 19406 PULLER

19394 SUPPORT 19440 SUPPORT 94814 NUT 225136 WASHER

NOTE: Each tool part number can also be ordered separately.

5054B Rewind Tool

5056 B Pump, Oil Evacuator

Breaker Point Plunger Hole Servicing

Screwdrivers – Carburetor Jet

19164 Cam Bearing Plug Gauge

19245 Carburetor Tap Set

@19260 Trip Cord and Switch

@19278 Test Plug Adapter

19305 Carburetor Offset Screwdriver

19310 Flywheel Holder

@ Subject to remaining factory inventory

19340 Ring Expander

19344 Roll Pin Driver

19345 Reamer Guide

19346 Valve Guide Reamer

19347 Valve Spring Compressor

19349 Bearing Driver

19351 Cylinder Support

@19352 Tang Bender