Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 6 views

    Disassembly: 1. Remove Rear End Cover

    Uploaded by

    Miguel ruiz
    This document provides instructions for disassembling an alternator. The key steps include: 1. Removing the rear end cover, brush holder, voltage regulator, and rectifier holder. 2. Using specialty tools (SST) to loosen and remove the pulley nut and pulley. 3. Removing the rectifier end frame by taking off nuts and a wire clip. Then using an SST tool to separate the rectifier end frame from the rotor.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Disassembly: 1. Remove Rear End Cover

    Uploaded by

    Miguel ruiz
    6 views2 pages
    This document provides instructions for disassembling an alternator. The key steps include: 1. Removing the rear end cover, brush holder, voltage regulator, and rectifier holder. 2. Using specialty tools (SST) to loosen and remove the pulley nut and pulley. 3. Removing the rectifier end frame by taking off nuts and a wire clip. Then using an SST tool to separate the rectifier end frame from the rotor.

    Original Description:

    toyota celica

    Original Title

    m_ch_0006

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for disassembling an alternator. The key steps include: 1. Removing the rear end cover, brush holder, voltage regulator, and rectifier holder. 2. Using specialty tools (SST) to loosen and remove the pulley nut and pulley. 3. Removing the rectifier end frame by taking off nuts and a wire clip. Then using an SST tool to separate the rectifier end frame from the rotor.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    6 views2 pages

    Disassembly: 1. Remove Rear End Cover

    Uploaded by

    Miguel ruiz
    This document provides instructions for disassembling an alternator. The key steps include: 1. Removing the rear end cover, brush holder, voltage regulator, and rectifier holder. 2. Using specialty tools (SST) to loosen and remove the pulley nut and pulley. 3. Removing the rectifier end frame by taking off nuts and a wire clip. Then using an SST tool to separate the rectifier end frame from the rotor.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 2

    CH−6

    CHARGING − ALTERNATOR
    CH025−02

    DISASSEMBLY
    Plate Terminal
    1. REMOVE REAR END COVER
    (a) Remove the nut and terminal insulator.
    (b) Remove the bolt, 3 nuts, plate terminal and end cover.

    B07732

    2. REMOVE BRUSH HOLDER AND VOLTAGE REGULA-


    TOR
    (a) Remove the brush holder cover from the brush holder.
    (b) Remove the 5 screws, brush holder and voltage regulator.
    (c) Remove the seal plate from the rectifier end frame.

    B07733

    3. REMOVE RECTIFIER HOLDER


    (a) Remove the 4 screws and rectifier holder.
    (b) Remove the 4 rubber insulators.

    B07734

    4. REMOVE PULLEY
    Turn (a) Hold SST (A) with a torque wrench, and tighten SST (B)
    clockwise to the specified torque.
    SST 09820−63010
    SST (A)
    Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
    (b) Check that SST (A) is secured to the rotor shaft.

    SST (B)
    B00210

    (c) Mount SST (C) in a vise.


    (d) Insert SST (B) into SST (C), and attach the pulley nut to
    SST (C).
    SST (B)
    SST (C)
    Insert

    B00224

    1ZZ−FE, 2ZZ−GE ENGINE (RM733E)


    CH−7
    CHARGING − ALTERNATOR

    (e) To loosen the pulley nut, turn SST (A) in the direction
    SST (C)
    shown in the illustration.
    NOTICE:
    To prevent damage to the rotor shaft, do not loosen the
    pulley nut more than one−half of a turn.
    SST (A)
    (f) Remove the alternator from SST (C).

    Turn B00237

    (g) Turn SST (B), and remove SST (A and B).


    Turn
    (h) Remove the pulley nut and pulley.

    SST (A)

    SST (B) B00322

    Wire Clip 5. REMOVE RECTIFIER END FRAME


    (a) Remove the 4 nuts and wire clip.

    B07735

    (b) Using SST, remove the rectifier end frame.


    SST 09286−46011
    (c) Remove the alternator washer from the rotor
    SST
    6. REMOVE ROTOR FROM DRIVE END FRAME

    B09160

    1ZZ−FE, 2ZZ−GE ENGINE (RM733E)

    You might also like