Selection Method of Surfactants For Chemical Enhanced Oil Recovery
Selection Method of Surfactants For Chemical Enhanced Oil Recovery
Selection Method of Surfactants For Chemical Enhanced Oil Recovery
Abstract
Alternative energy sources have not yet presented suitable to meet the energy demand of the
world; therefore crude oil will play furthermore an essential role in the energy consumption in the
future. EOR is a challenging field for several scientific disciplines. The number of patents
highlights the importance of this area. Most of the publications label that the target of the
chemical processes is the reduction of IFT between the displacing liquid and oil phase. Based on
the results in the last two decades the surfactants and flow modifier type polymers have shown
more potential for a higher efficiency of the EOR than in any other methods. The aim of this work
was to develop different surfactant testing methods that are capable to characterize the most
important surfactant properties separately and to evaluate their combined or complementary
effects. There was no correlation between the specific characteristics. But the weak correlation
was detected by using the CE complex evaluation method. Further improvements could contribute
significantly to improve the selectivity of the new experimental non-ionic surfactants for EOR
applications.
Keywords
EOR, Method Development
1. Introduction
Alternative energy sources have not yet presented suitable to meet the energy demand of the world; therefore
crude oil will play furthermore an essential role in the energy consumption in the future. Considering the fact
that the easily recoverable oil is running out and much oil remains in the reservoir after conventional methods
*
Corresponding author.
How to cite this paper: Nagy, R., Sallai, R., Bartha, L. and Vágó, Á. (2015) Selection Method of Surfactants for Chemical En-
hanced Oil Recovery. Advances in Chemical Engineering and Science, 5, 121-128.
http://dx.doi.org/10.4236/aces.2015.52013
R. Nagy et al.
have been exhausted, the implementation of Enhanced Oil Recovery has become crucial to guarantee a continu-
ing crude oil supply [1].
The Enhanced Oil Recovery (EOR) technology covers the injection of specific type of a fluid or fluids into
the reservoir by several methods (e.g.: chemical, thermal and microbial). The injected fluid promotes to dislo-
cate of crude oil toward the producing well. Besides, the injected fluids interact with the reservoir rock/oil sys-
tem and generate advantageous conditions for oil recovery. These interactions incorporate lowering the interfa-
cial tension (IFT), improving the flow properties, modify wettability and help developing preferential phase be-
haviour. As a consequence of the interactions, physical and chemical mechanisms can occur, as well as the for-
mation of thermal energy [2]-[5].
EOR is a challenging field for several scientific disciplines. The number of patents highlights the importance
of this area. Most of the publications label that the target of the chemical processes is the reduction of IFT be-
tween the displacing liquid and oil phase. Based on the results in the last two decades the surfactants and flow
modifier type polymers have shown more potential for a higher efficiency of the EOR than in any other methods
[6] [7].
Chemical flooding of oil reservoirs could be the one of the most successful method to increase oil recovery
rate of the depleted reservoirs. The research and developing projects of the EOR surfactants are very costly due
to the expensive field tests. Numerous screening test methods have been elaborated to reduce the costs and to
estimate the potential efficiency of the tested surfactant compositions [3] [7] [8].
However, the previous experiments showed that the surfactant composition has to be effective under different
and often extreme conditions, which are complicated to be modelled in the laboratories. There is no generally
accepted test method for the selection of surfactants. Therefore, the further development of screening methods
remains important.
The aim of this work was to develop different surfactant testing methods that are capable to characterize the
most important surfactant properties separately and to evaluate their combined or complementary effects.
2. Materials
Preparation of the Surfactant and Surfactant-Polymer Solutions
For the preparation of the experimental colloid solutions one anionic (MOLANIONIC) and two nonionic
(PENONIONIC I and II) surfactants were used, that were developed and produced by cooperative research
groups of University of Pannonia and Hungarian Oil and Gas Company (MOL Plc). Furthermore partially hy-
drolysed synthetic polyacrylamide was applied as a flow modifier type polymer.
The polymer-surfactant solutions were prepared by using brine, derived from the petroleum reservoir of Al-
győ (Hungary).
The surfactant packages were prepared of the following components (detailed in Table 1).
The flow modifier type polymer (PAM type sulfonated co-polymer) was used in a concentration of 1000 ppm.
The total concentration of the surfactant packages in the mixtures was 15,000 ppm.
3. Methods
A complex laboratory screening method was developed to definite the properties of EOR type surfactants by the
application of the following methods to determine the surface-active properties and also to study the possibility
of the complex evaluation of the measurement data.
122
R. Nagy et al.
MOLANIONIC 55 60
PENONIONIC I 25 40
PENONIONIC II 20 -
3.2. Determination of the Oil Displacement Effect (ODE) by Thin Layer Chromatography
(TLC)
The complex surface activity method has not been reported in the specific publications, which could be the ex-
tent to porous surfaces characterized by washing efficiency of the oil. It was developed a method for oil flushing
effect, that based on the foundations of thin layer chromatography of organic chemical analysis has been used.
The first step of the test procedure is the preparation of the thin layer. First the glass slab should be washed
with water and n-heptane and let dry. Thereafter the slab should be plunged into chloroform-real core sand dis-
persion and let dry for 20 minutes. Then 4 µl of crude oil should be spotted on the thin layer at 2 cm from the
base of the glass slab. Then the sample should be run by pH adjusted (between 8.0 - 8.5) brine containing 1% of
the emulsifier mixture at 80˚C for 3 hours. The drying of the thin layer should be carried out at room tempera-
ture after 24-hour storage. The oil displacement efficiency (ODE) of the surfactant composition can be evaluated
by the distance from the centre of the oil spot to the upper edge of the spot measured in mm. The layers after the
3-hours run-time should be photographed with a digital camera, and the data should be recorded and stored in a
database.
The maximum difference between the parallel results was in the interval of ±10%.
123
R. Nagy et al.
for characterization and evaluation of the experimental surfactant mixtures for EOR purposes.
In our study, as a model two different packages of experimental surfactants were examined (of two-and
three-components). The suitability of these surfactant packages for EOR purposes has been studied by the pre-
sented test methods.
The three screening methods and the oil displacement test were used also for the complete classification of
surfactant packages. The second aim of this work was to use the screening methods for the optimization the
compositions of two surfactant packages consisting non-ionic type compounds with different molecular struc-
ture by variation of the ratio of the polar and nonpolar groups in the mixture of molecules obtained by reaction
of fatty acids and a polyalkanol-amine.
0.06
0.05
0.04
IFT, mNm
0.03
IFT 1%
0.02
IFT 5%
0.01
0
0 10 20 30 40
Additional oil yield%
Figure 1. Relationship between the additional oil yield and the IFT.
0,08
0,07
0,06
0,05
IFT, mNm
0,04
IFT 1%
0,03
IFT 5%
0,02
0,01
0
80 85 90 95 100
Monoester content, %
124
R. Nagy et al.
40
35
125
R. Nagy et al.
0,08
0,07
0,06
0,05
IFT, mNm
0,04
IFT 1%
0,03
IFT 5%
0,02
0,01
0
75 80 85 90 95 100
EE 1h 80°C, %
30
25
Additional oil yield, %
20
R² = 0.358
15
10
0
0 5 10 15 20 25 30
ODE, mm
the preliminary tests the ST surfactant mixtures seemed also appropriate for EOR purposes that were supported
by numerous of measurement data.
The IFT values were found below 0.1 m·Nm, therefore this series of the surfactant mixtures can be suitable as
well for EOR application. Between the emulsifying effect and the interfacial tension there was not clear tendency
126
R. Nagy et al.
too. It was also found, that the IFT method in itself is not enough for classification of surfactants for EOR.
On the other hand it was found, that the additional oil yield values were also over 20% that can be considered
a successful oil recovery ratio. In addition between the ODE and additional oil yield values an increasing ten-
dency was observed with a low level of significance.
4.3. CE Calculation
Based on the results of the single laboratory test methods it was supposed that the high replacement efficiency of
the surfactant packages only by a well balanced combination of the surfactant properties can be achieved. That
is why a complex evaluation system was introduced and studied.
For the combined evaluation (CE) of the three properties an evaluation-equation was created and used to
characterize the potential efficiency of the experimental surfactant for EOR. According to the mathematical cal-
culations by using the measurement the best approximated equation was defined by the next formula:
ODE ⋅ 0.25 ⋅ EE
CE =
IEF2 ⋅100
The calculated CE value of the series of the SM and ST surfactants in a function of additional oil yield related
to residual oil shows Figure 6.
It was concluded, that by increasing the CE value a better additional oil yield could be estimated. In spite of
the weak correlation it is supposed that by using also other complementary characteristics of the surfactant
packages the estimation of oil recovery may be further improved. Figure 6 showed that in accordance with the
general practice by using these experimental surfactant mixtures only a limited value (80%) from the residual
crude oil can be recovered by this SP method. Based on these results next enhancements are planned, which
could further contribute to reduce the selection of new surfactants. By the use of the developed methods the
number of performed measurement can be approximately one-tenth reduced.
5. Conclusions
The experimental results were summarized as follows:
• A new complex laboratory method was developed to estimate the efficiency of the experimental surfactant
packages for EOR.
• Different levels of correlations have been obtained between the surface-active properties and the additional
oil yield.
• Slightly correlation was found between the CE factor and the additional oil yield that could open new oppor-
tunities for cost reduction of the development.
• By these measurements the number of experimental surfactants and their mixtures can be reduced.
12000
R² = 0.771
10000
8000
CE
6000
4000
2000
0
0,00 20,00 40,00 60,00 80,00 100,00
Additional oil yield, %
Figure 6. Relationship between the CE and additional oil yield (related to re-
sidual oil) in case of SM and ST-surfactants.
127
R. Nagy et al.
There was no correlation between the specific characteristics. But the weak correlation was detected by using
the CE complex evaluation method. Further improvements could contribute significantly to improve the selec-
tivity of the new experimental non-ionic surfactants for EOR applications.
References
[1] Thomas, S. (2008) Enhanced Oil Recovery—An Overview. Oil & Gas Science and Technology, 63, 9-19.
http://dx.doi.org/10.2516/ogst:2007060
[2] Gaillard, N., Giovannetti, B. and Favero, C. (2010) Improved Oil Recovery Using Thermally and Chemically Protected
Compositions Based on Co- and Terpolymers Containing Acrylamide. SPE Improved Oil Recovery Symposium, Tulsa,
24-28 April 2010, Document ID: SPE-129756-MS. http://dx.doi.org/10.2118/129756-MS
[3] Levitt, D.B. and Pope, G.A. (2008) Selection and Screening of Polymers for Enhanced-Oil Recovery. SPE Symposium
on Improved Oil Recovery, Tulsa, 20-23 April 2008, Document ID: SPE-113845-MS.
[4] Zhong, C, Luo, P., Ye, Z. and Chen, H. (2009) Characterization and Solution Properties of a Novel Water-Soluble
Terpolymer for Enhanced Oil Recovery. Polymer Bulletin, 62, 79-89. http://dx.doi.org/10.1007/s00289-008-1007-6
[5] Schramm, L.L. (2000) Surfactants: Fundamentals and Applications in the Petroleum Industry. Cambridge University
Press, Cambridge.
[6] Myers, D. (2006) Surfactant Science and Technology. Wiley-Interscience, Hoboken.
[7] Jeirani, Z., Mohamed Jan, B., Si Ali, B., Noor, I.M., See, C.H. and Saphanuchart, W. (2013) Formulation, Optimiza-
tion and Application of Triglyceride Microemulsion in Enhanced Oil Recovery. Industrial Crops and Products, 43,
6-14. http://dx.doi.org/10.1016/j.indcrop.2012.07.002
[8] Nasr-EI-Din, H.A., Hawkins, B.F. and Green, K.A. (1992) Recovery of Residual Oil Using the Alkali/Surfactant/
Polymer Process: Effect of Alkali Concentration. Journal of Petroleum Science and Engineering, 6, 381-401.
http://dx.doi.org/10.1016/0920-4105(92)90064-8
128