Kato30t nk250 PDF
Kato30t nk250 PDF
Kato30t nk250 PDF
30t crane
jack down (over the front and rear) 3.0 The total rated loads shown are based on the actual
working radius which includes and deflection of the boom
4.0 Boom operations must be related to the working radius.
However the working radius shown for jib operations are
B(m) 10.5m 14.2m 18m 21.7m 25.5m 29.2m 33m based upon the values obtained when the boom is fully
extended (33m). Jib operations should be performed on
2.5 25,000 20,000 16,000 the basis of boom angle or regardless of boom length
3.0 25,000 20,000 16,000 5.0 If the boom length exceeds the specified value, refer to
3.5 25,000 20,000 16,000 12,000 the rated lifting capacities for the boom length and the next
4.0 22,900 20,000 16,000 12,000 11,500 highest boom length. The crane should be operated within
4.5 21,000 20,000 16,000 12,000 11,500 the smaller lifting capacity.
5.0 19,400 18,400 16,000 12,000 11,500 9,000 6.0 The boom angle must not be reduced to less than the
6.0 16,200 15,300 13,700 12,000 11,500 9,000 7,000 number of degrees shown as the critical boom angle at the
7.0 13,700 12,650 11,950 11,000 10,000 9,000 7,000 bottom of each load chart, In the vent of such a reduction the
crane will tip.
8.0 11,500 10,650 10,550 10,200 8,900 8,200 7,000
8.8 9,500 9,300 9,200 9,400 8,250 7,600 6,400 7.0 The weight of the hook (280kg for 25,000kg capacity,
9.0 9,050 8,800 9,200 8,050 7,450 6,400 60kg for 3,400kg capacity), slings and all similarly used load
handling devices must be added to the weight of the load.
10.0 7,400 7,200 7,700 7,300 6,750 6,250
12.0 5,150 5,000 5,450 5,750 5,650 5,700 8.0 Standard number of part lines for each boom length are
12.5 4,700 4,600 5,000 5,300 5,450 4,800 as shown below. Load per line should not surpass 3.125kg
13.0 4,250 4,650 4,900 5,050 4,550 9.0 Total rated load of the single top should not exceed
14.0 3,600 4,000 4,250 4,450 4,450 3,400kg
16.0 2,550 3,000 3,250 3,400 4,100 10.0 Free fall operation should be performed only without any
16.3 2,400 2,850 3,100 3,250 3,500 load on the hook.
18.0 2,200 2,500 2,700 3,400 11.0 Deduct 1,800kg from the rated lifting loads of the main
20.0 1,550 1,850 2,050 2,800 boom, when the jib is attached to the main boom head. The
22.0 1,350 1,550 2,200 single top must not be used whilst the jib is attached.
23.8 950 1,200 1,700 12.0 Over the front lifting performance is inferior to over the
26.0 800 1,350 sides/over the rear lifting performance. Great care must be
27.5 600 950 taken when transferring loads from over the side to over the
29.0 750 front since there is a distinct danger of overloading.
30.0 550 13.0 The cranes safe lifting ability over the sides will vary
450 due to the amount the outriggers are extended. Refer to the
rated load chart for each respective outrigger configuration.
When the front jack is down and the outriggers are set at their
A: BOOM LENGTH B: WORKING RADIUS (m) minimum extension the stability of the crane is the same as if
the front jack was not in use.
14.0 Special weather caution: Should wind gusts exceed
10m/sec postpone the operation. Refer to the operation and
maintenance manual
15.0 Refer to the crane manual
8.0 Standard number of part lines for each boom length are as shown 13.0 The cranes safe lifting ability over the sides will vary due to the
below. Load per line should not surpass 3,125kg. amount of outriggers, are extended. Refer to the rated load chart
for each respective outrigger configuration. When the front jack
BOOM 10.5m 14.2m 18.0m 21.7m 25.5m 29.2m 33.0m Both Single is down and the outriggers are set to their minmum extension the
LENGTH Jibs Top stability of the crane is the same as if the front jack was not in use.
No. of Part 8 8 8 4 4 4 4 1 1 14.0 Special weather caution: Should wind gusts exceed 10m/sec
Lines
postpone the operations. Refer to the operation and maintnance
9.0 Total load of the single top should not exceed 3,400kg. manual.
10.0 Free fall operation should be performed only without any load on 15.0 Refer to the crane manual
the hook.
11.0 Deduct 1,800kg from the rated lifting loads of the main boom, when
the jib is attached to the main boom head. The single top must not
be used whilst the jib is attached.