Caja de Super 10

® ®
Eaton Fuller Heavy Duty Transmissions

RTLO-1X610 Models
RTLO-1X610-T2 Models
Service Manual TRSM-0550 April 2006
For the most current information, visit the Roadranger web site at www.roadranger.com
Precautions
Warnings and Precautions
Before starting a vehicle always be seated in the driver’s seat, place the transmission in neutral, set the parking brakes and
disengage the clutch.
Before working on a vehicle place the transmission in neutral, set the parking brakes and block the wheels.
Before towing the vehicle place the transmission in neutral, and lift the rear wheels off the ground, remove the axle shafts,
or disconnect the driveline to avoid damage to the transmission during towing.
The description and specifications contained in this service publication are current at the time of printing.
Eaton Corporation reserves the right to discontinue or modify its models and/or procedures and to change specifications at any
time without notice.
Any reference to brand name in this publication is made as an example of the types of tools and materials recommended for use
and should not be considered an endorsement. Equivalents may be used.
This symbol is used throughout this manual to call attention to procedures where carelessness or failure to follow
specific instructions may result in personal injury and/or component damage.
Departure from the instructions, choice of tools, materials and recommended parts mentioned in this publication may jeopardize
the personal safety of the service technical or vehicle operator.
Warning: Failure to follow indicated procedures creates a high risk of personal injury to servicing technician.
Caution: Failure to follow indicated procedures amy cause component damage of malfunction.
Note: Additional service information not covered in the service procedures.
Tip: Helpful removal and installation procedures to aid in the service of this unit.
Always use genuine Eaton replacement parts.
1
Table of Contents
General Information How to Install the Input Shaft

Without Disassembling the Transmission .............57
General Service Practices and Part Inspection ............ 1

How to use this Manual ............................................... 5
Model Designation ...................................................... 8
Shift Bar Housing
Power Flow ................................................................. 9
Timing Procedures .................................................... 13 Shift Bar Housing Identification .................................59
Tool Reference .......................................................... 15 How to Disassemble the Gear Shift Lever ..................61
How to Assemble the Gear Shift Lever ......................63
How to Disassemble the Standard Shift Bar Housing 65
Preventive Maintenance How to Assemble the Standard Shift Bar Housing .....68
How to Disassemble the Standard
Shift Bar Housig (w/Super 10 on cover) ................71
Lubrication ................................................................ 16 How to Assemble the Standard
Preventative Maintenance ......................................... 18 Shift Bar Housing (w/Super 10 on cover) ..............74
Inspection ................................................................. 20 How to Disassemble the Forward
Rear Seal Maintenance .............................................. 21 Shift Bar Housing (w/Super 10 on cover) ..............77
How to Assemble the Forward
Shift Bar Housing(w/Super 10 on cover) ...............80
External Parts How to Disassemble the New Forward
Shift Bar Housing (w/Super 10 on cover) ..............83
How to Assemble the New Forward
How to Disassemble the External Parts ..................... 22 Shift Bar Housing (w/Super 10 on cover) ..............86
How to Assemble the External Parts ......................... 23
How to Remove the Air Lines and Hose .................... 24
How to Install the Air Lines and Hose ....................... 25
How to Remove the Air Filter/Regulator .................... 26
Front Section
How to Install the Air Filter/Regulator ....................... 27
How to Remove a Roadranger Valve ......................... 28
How to Install a Roadranger Valve ............................ 29 How to Disassemble the Front Section ......................89
How to Remove the Range Actuator Valve ................ 30 How to Remove the Auxiliary Drive Gear Assembly ...90
How to Install the Range Actuator Valve ................... 31 How to Remove the Reverse Idler Gear Assembly .....91
How to Remove the Top 2 Valve Assembly ............... 33 How to Remove the Countershaft Bearings ...............93
How to Install the Top 2 Valve Assembly .................. 34 How to Remove the Mainshaft Assembly ..................95
How to Remove the Gear Shift Lever ........................ 35 How to Remove the Countershaft Assemblies ...........96
How to Install the Gear Shift Lever ............................ 36 How to Remove the Input Shaft Assembly ................97
How to Remove the Shift Bar Housing ...................... 37 How to Assemble the Front Section ...........................99
How to Install the Shift Bar Housing ......................... 38 How to Install the Reverse Idler Gear Assembly ......100
How to Remove the Output Yoke/Companion Flange 39 How to Install the Countershaft Assemblies ............102
How to Install the Output Yoke/Companion Flange ... 40 How to Install the Countershaft Bearings .................103
How to Remove the Auxiliary Section How to Install the Input Shaft Assembly ..................105
Without Tapered Bearings ..................................... 41 How to Install the Mainshaft Assembly ....................108
How to Install the Auxiliary Section How to Install the Auxiliary Drive Gear Assembly ....109
Without Tapered Bearings ..................................... 43 How to Disassemble the Auxiliary Drive Gear Assembly
How to Remove the Auxiliary Section 110
With Tapered Bearings .......................................... 45 How to Assemble the Auxiliary Drive Gear Assembly 112
How to Install the Auxiliary Section How to Disassemble the Countershaft Assembly .....114
With Tapered Bearings .......................................... 48 How to Assemble the Countershaft Assembly .........115
The Shimming Procedure For Tapered Bearings ....... 50 How to Disassemble the Mainshaft Assembly .........117
How to Remove the Clutch Housing .......................... 53 How to Assemble the Mainshaft Assembly ..............119
How to Install the Clutch Housing ............................. 54
How to Remove the Input Shaft
Without Disassembling the Transmission ............. 55
Table of Contents
Auxiliary Section
How to Disassemble the Auxiliary Section .............. 124
How to Remove the Front Auxiliary Drive Gear ....... 125
How to Remove the Countershaft Assemblies
(w/Tapered Bearings) .......................................... 126
(w/Ball Bearings) A Series ................................... 128
How to Remove the Rear Auxiliary Drive Gear ........ 130
How to Disassemble the Range Cylinder Assembly 131
How to Disassemble the Output Shaft Assembly .... 135
How to Disassemble the Splitter Cylinder Assembly 137
How to Assemble the Auxiliary Section ................... 139
How to Assemble the Output Shaft Assembly ......... 140
How to Assemble the Output Shaft Assembly
(A Series) ........................................................... 143
How to Install the Countershaft Assemblies
(w/Tapered Bearings) ......................................... 147
(w/Ball Bearings) A Series .................................. 150
How to Assemble the Range Cylinder Assembly ..... 153
How to Install the Rear Auxiliary Drive Gear ............ 157
How to Assemble the Splitter Cylinder Assembly .... 158
How to Install the Front Auxiliary Drive Gear ........... 161
How to Disassemble the Synchronizer Assembly .... 162
How to Assemble the Synchronizer Assembly ........ 163
Options
How to Remove the Integral Oil Pump .................... 165
How to Install the Integral Oil Pump ....................... 167
How to Disassemble the Integral Oil Pump ............. 169
How to Assemble the Integral Oil Pump .................. 171
General Information
General Service Practices and Part Inspection
Disassembly
It is assumed in the detailed assembly instructions that the lubricant has been drained from the transmission, the necessary link-
age and vehicle air lines disconnected and the transmission has been removed from vehicle chassis. Removal of the gear shift
lever housing assembly (or remote control assembly) is included in the detailed instructions (External Parts/Shift Bar Housing/
How to Remove the Gear Shift Lever); however, this assembly MUST be detached from the shift bar housing before transmission
can be removed.
CAUTION: Follow closely each procedure in the detailed instructions, make use of the text, illustrations, and photographs provid-
ed.
Assemblies
When disassembling the various assemblies, such as the mainshaft, countershafts, and shift bar housing, lay all parts on a clean
bench in the same sequence as removed. This procedure will simplify assembly and reduce the possibility of losing parts.
Bearings
Carefully wash and lubricate all usable bearings as removed and protectively wrap until ready for use. Remove bearings planned
to be reused with pullers designed for this purpose.
Cleanliness
Provide a clean place to work. It is important that no dirt or foreign material enters the unit during repairs. Dirt is an abrasive and
can damage bearings. It is always good practice to clean the outside of the unit before starting the planned disassembly.
Input Shaft
The input shaft can be removed from the transmission without removing the countershaft, mainshaft, or main drive gear. Special
procedures are required and provided in this manual.
Snap Rings
Remove snap rings with pliers designed for this purpose. Snap rings removed in this manner can be reused, if they are not sprung
or loose.
When using Tools to Move Parts
Always apply force to shafts, housings, etc., with restraint. Movement of some parts is restricted. Never apply force to driven parts
after they stop solidly. The use of soft hammers, soft bars, and mauls for all disassembly work is recommended.
1
General Information
Inspection
General Information
Before assembling the transmission, check each part carefully for abnormal or excessive wear and damage to determine reuse or
replacement. When replacement is necessary, use only genuine Eaton® Fuller® Transmission parts to assure continued perfor-
mance and extended life from your unit.
Since the cost of a new part is generally a small fraction of the total cost of downtime and labor, avoid reusing a questionable part
which could lead to additional repairs and expense soon after assembly. To aid in determining the reuse or replacement of any
transmission part, consideration should also be given to the unit’s history, mileage, application, etc.
Recommended inspection procedures are provided in the following checklist.

Bearings
1. Wash all bearings in clean solvent. Check balls, rollers, and raceways for pitting, discoloration, and spalled areas. Replace
bearings that are pitted, discolored, spalled, or damaged during disassembly.
2. Lubricate bearings that are not pitted, discolored, or spalled and check for axial and radial clearances.
3. Replace bearings with excessive clearances.
4. Check bearing fit. Bearing inner races should be tight to shaft; outer races slightly tight to slightly loose in case bore. If
bearing spins freely in bore, case should be replaced.
Bearing Covers
1. Check covers for wear from thrust of adjacent bearing. Replace covers damaged from thrust of bearing outer race.
2. Check cover bores for wear. Replace those worn or oversized.
Clutch Release Parts
1. Check clutch release parts. Replace yokes worn at cam surfaces and bearing carrier worn at contact pads.
2. Check pedal shafts. Replace those worn at bushing surfaces.
Gears
1. Check gear teeth for frosting and pitting. Frosting of gear teeth faces presents no threat of transmission failure. Often in
continued operation of the unit, frosted gears “heal” and do not progress to the pitting stage. In most cases, gears with
light to moderate pitted teeth have considerable gear life remaining and can be reused, but gears in the advanced stage
of pitting should be replaced.
2. Check for gears with clutching teeth abnormally worn, tapered, or reduced in length from clashing during shifting. Re-
place gears found in any of these conditions.
3. Check axial clearance of gears.
Gear Shift Lever Housing Assembly
1. Check spring tension on shift lever. Replace tension spring if lever moves too freely.
2. If housing is disassembled, check gear shift lever bottom end and shift finger assembly for wear. Replace both gears if
excessively worn.
Gray Iron Parts
1. Check all gray iron parts for cracks and breaks. Replace parts found to be damaged.
2
General Information
Oil Return Threads and Seals

1. Check oil return threads on the input shaft. If return action of threads has been destroyed, replace the input shaft.
2. Check oil seal in rear bearing cover. If sealing action of lip has been destroyed, replace seal.
O-Rings
1. Check all O-rings for cracks or distortion. Replace if worn.
Reverse Idler Gear Assemblies
1. Check for excessive wear from action of roller bearings.
Shift Bar Housing Assembly
1. Check for wear on shift yokes and blocks at pads and lever slot. Replace excessively worn parts.
2. Check yokes for correct alignment. Replace sprung yokes.
3. Check lockscrews in yoke and blocks. Tighten and rewire those found loose.
4. If housing has been disassembled, check neutral notches of shift bars for wear from interlock balls.
Sliding Clutches
1. Check all shift yokes and yoke slots in sliding clutches for extreme wear or discoloration from heat.
2. Check engaging teeth of sliding clutches for partial engagement pattern.
Splines
1. Check splines on all shafts for abnormal wear. If sliding clutch gears, companion flange, or clutch hub has worn marks
in the spline sides, replace the specific shaft affected.
Synchronizer Assembly
1. Check synchronizer for burrs, uneven and excessive wear at contact surface, and metal particles.
2. Check blocker pins for excessive wear or looseness.
3. Check synchronizer contact surfaces on the synchronizer cups for wear.
Washers
1. Check surfaces of all washers. Washer scored or reduced in thickness should be replaced.
3
General Information
Assembly
General Information
Make sure that case interiors and housings are clean. It is important that dirt and other foreign materials are kept out of the trans-
mission during assembly. Dirt is an abrasive and can damage polished surfaces of bearings and washers. Use certain precautions,
as listed below, during assemble.
Axial Clearances
Maintain original axial clearances of .006" to .015" for mainshaft gears.
Bearings
Use a flange-end bearing driver for bearing installation. These special drivers apply equal force to both bearing races, preventing
damage to balls/rollers and races while maintaining correct bearing alignment with bore and shaft. Avoid using a tubular or sleeve-
type driver, whenever possible, as force is applied to only one of the bearing races.
Capscrews
To prevent oil leakage and loosening, use Eaton/Fuller sealant #71205 on all capscrews.
Gaskets
Use new gaskets throughout the transmission as it is being rebuilt. Make sure all gaskets are installed. An omission of any gasket
can result in oil leakage or misalignment of bearing covers.
Initial Lubrication
Coat all limit washers and shaft splines with Lubriplate during assembly to prevent scoring and galling of such parts.
O-Rings
Lubricate all O-rings with silicon lubricant.
Universal Joint Companion Flange or Yoke
Pull the companion flange or yoke tightly into place with the output shaft nut, using 450-500 Lbf-ft of torque. Make sure the speed-
ometer drive gear or a replacement spacer of the same width has been installed. Failure to pull the companion flange or yoke tightly
into place can result in damage to the mainshaft rear bearing.
IMPORTANT: See the appropriate Illustrated Parts Lists (specified by model series) to ensure that proper parts are used during
assemble of the transmission.
4
General Information
How to use this Manual

This manual is designed to provide detailed information necessary to service and repair the Eaton® Fuller® transmissions listed
on the front.
As outlined on the first page, the manual has been divided into its main components: external parts, shift bar housing, front sec-
tion, auxiliary section, and options (if applicable). Each component has its own tabbed section. Each tabbed section has its own
table of contents and procedural flow charts. The table of contents lists the procedures. The flow charts represent the order in
which the transmission should be disassembled or assembled. The procedures have two parts, disassembly or removal and re-
assembly or installation.
As mentioned the flow charts represent the order in which the transmission should be disassembled or assembled.
The following is an example of how to disassemble the auxiliary section, specifically the range cylinder assembly.
5
General Information
Follow the flow chart "How to Disassemble the Auxiliary Section".
General Information
1. Remove the auxiliary section from the front box.
2. Remove the front auxiliary drive gear and yoke.
3. Remove the countershaft assemblies.
4. Remove the rear auxiliary drive gear.
5. Remove the range cylinder assembly.
Auxiliary
1 Section
Front Auxiliary Drive

2 Gear and Yoke
3 Countershaft
Assemblies
Rear Auxiliary
4 Drive Gear
Range
Cylinder 5
Assembly
Desassemble
Synchronizer
Assembly
Output
Shaft
Assembly
Splitter
Cylinder
Assembly
6
General Information
Once the range cylinder parts have been replaced, assemble the auxiliary section according to the "How to Assemble the Auxiliary
Section".
1. Assemble the output shaft assembly.
2. Assemble the synchronizer assembly, if it was disassembled.
3. Install the countershaft assemblies.
4. Install the range cylinder assembly.
Output
1 Shaft
Assembly
Assemble
Synchronizer 2
Assembly
Countershaft
3 Assemblies
Range
4 Cylinder
Assembly
Rear Auxiliary
Drive Gear
Splitter
Cylinder
Assembly
Front Auxiliary Drive

Gear and Yoke
Auxiliary
Section
7
General Information
Model Designation
General Information
General Information and other transmission identification information are stamped on the transmission tag. To identify the trans-
mission model designation and serial number, locate the tag on the transmission and then locate the numbers as shown.
WARNING: Do not remove or destroy the transmission identification tag.
PTO Code
Eaton Fuller
Transmissions
Model Serial
RTO-14710-AS2
Eaton Corporation
Made
Transmission Div
In
Kalamazoo, MI 49003
R T L O - 1 4 6 1 0 A
Roadranger
Gear Ratio
Twin Countershaft
Low Inertia Forward Speeds
Overdrive
Design Level 6 ="Multi-Mesh" Gearing
Torque x 100
8
General Information
Power Flow
The transmission must efficiently transfer the engine's power to the vehicle's driveline. Knowledge of what takes place in the
transmission is helpful when troubleshooting and making repairs.
1st Gear
• Power (torque) from the vehicle's engine is transferred to the transmission's input shaft.(1)
• The input shaft external splines engage the main drive gear internal splines.(2)
• Torque is split between the two countershaft drive gears.(3)
• Torque is delivered along both countershafts to the mating countershaft gears of the "engaged" mainshaft gear. The fol-
lowing cross section view illustrates a 1st speed gear engagement.(4)
• The external clutching teeth of the sliding clutch engage with the internal clutching teeth of the mainshaft gear which
transfers torque to the mainshaft.(5)
• The mainshaft transfers torque directly to the rear auxiliary drive gear sliding clutch which is in the rearward posi-
tion.(6)
• The rear auxiliary drive gear splits torque between the two auxiliary countershaft drive gears.(7)
• Torque is delivered along both countershafts to the LO range gear in the auxiliary section.(8)
• The LO range gear delivers torque to the output shaft through the range synchronizer sliding clutch.(9)
• The output shaft delivers torque to the driveline components.(10)
9
General Information
2nd Gear
General Information
lowing cross section view illustrates a 2nd speed gear engagement.(4)
• The mainshaft transfers torque directly to the auxiliary drive gear sliding clutch which is in the forward position.(6)
• The auxiliary drive gear splits torque between the two auxiliary countershaft drive gears.(7)
• Torque is delivered along both countershafts to the LO range gear in the auxiliary section.(8)
• The LO range gear delivers torque to the output shaft through the range synchronizer sliding clutch.(9)
10
General Information
7th gear
lowing cross section view illustrates a 7th speed gear engagement.(4)
• The mainshaft transfers torque directly to the rear auxiliary drive gear sliding clutch which is in the rearward posi-
tion.(6)
• Torque is delivered to the back of the rear auxiliary drive gear. The range synchronizer sliding clutch is in the forward
position, transferring torque directly to the output shaft.(7)
11
General Information
8th Gear
General Information
lowing cross section view illustrates a 8th speed gear engagement.(4)
• The mainshaft transfers torque directly to the front auxiliary drive gear sliding clutch which is in the forward position.(6)
• The front auxiliary drive gear splits torque between the two auxiliary countershaft drive gears.(7)
• Torque is delivered along both countershafts to the rear auxiliary drive gear.(8)
• Torque is transferred to the range synchronizer sliding clutch which is in the forward position delivering torque directly
to the output shaft.(9)
12
Timing
Timing Procedures
It is essential that both countershaft assemblies of the front and auxiliary sections are "timed." This assures proper tooth contact
is made between mainshaft gears seeking to center on the mainshaft during torque transfer and mating countershaft gears that
distribute the load evenly. If not properly timed, serious damage to the transmission is likely to result from unequal tooth contact
causing the mainshaft gears to climb out of equilibrium.
Timing is a simply procedure of marking the appropriate teeth of a gear set prior to installation and placing them in proper mesh
while in the transmission. In the front section, it is necessary to time only the drive gear set. And depending on the model, only
the LO range, deep reduction, or splitter gear set is timed in the auxiliary section.
Front Section
A. Marking countershaft drive teeth.
1. Prior to placing each countershaft assembly into the case, clearly mark the tooth located directly over the drive gear
keyway as shown. This tooth is stamped with an "O" to aid identification.
B. Marking main drive gear teeth.

1. Mark any two adjacent teeth on the main drive gear.
2. Mark the two adjacent teeth located directly opposite the first set marked on the main drive gear. As shown to the left,
there should be an equal number of unmarked gear teeth on each side between the marked sets.
13
Timing
C. Meshing marked countershaft drive gear teeth with marked main drive gear teeth.
(After placing the mainshaft assembly into the case, the countershaft bearings are installed to complete installation of the coun-
General Information
tershaft assemblies.)
1. When installing the bearings on the left countershaft, mesh the countershaft drive gear marked tooth with either set of
main drive gear two marked teeth.
2. Repeat the procedure when installing the bearings on the right countershaft, make use of the remaining set of main
drive gear two marked teeth to time assembly.
Auxiliary Section
A. Timing the auxiliary countershafts.
Standard Auxiliary Section
1. Mark any two teeth on the LO range gear. Then mark two teeth located directly opposite the first marked.
2. Prior to placing each auxiliary countershaft assembly into housing, mark the tooth on each auxiliary countershaft
assembly LO range gear stamped with the "O".
3. Follow the assembly procedures in the "Auxiliary Section".
Helical Auxiliary Section

1. Mark any tooth on the LO range gear. Then mark a tooth located directly opposite the first marked.
2. Prior to placing each auxiliary countershaft assembly into housing, mark the two teeth on each auxiliary countershaft
assembly LO range gear stamped with the two "O"s. Repeat the procedure on each auxiliary countershaft reduction gear.
3. Follow the assembly procedures in the "Auxiliary Section".
14
Tool Reference
Tool Reference
Some repair procedures pictured in this manual show the use of specialized tools. Their actual use is recommended as they
make transmission repair easier, faster, and prevent costly damage to critical parts.
But for the most part, ordinary mechanic's tools such as socket wrenches, screwdrivers, etc., and other standard shop items
such as a press, mauls and soft bars are all that is needed to successfully disassemble and reassemble any Eaton Fuller Trans-
mission.
The specialized tools can be obtained from a tool supplier or made from tool prints as required by the individual user. Detailed
Eaton Fuller Transmission Tool Prints are available upon request by writing to:
Roadranger Literature Services
Attn: Contract 4 / CA#182
1750 Wallace Ave.
St. Charles, IL 60174-3404
Phone: 888-ETN-INFO (386-4636)
15
Lubrication / Application Information
Lubrication
For a list of Eaton Approved Synthetic Lubricants, see TCMT-0021 or call 1-800-826-HELP (4357)
The use of lubricants not meeting these requirements will affect warranty coverage.
Additives and friction modifiers must not be introduced.
Preventive Maintenance
Never mix engine oils and gear oils in the same transmission.
Buy from a reputable dealer

For a list of approved and reputable dealers, write to:
Eaton Corporation
Worldwide Marketing Services
P.O.Box 4013
Kalamazoo MI 49003
Transmission Operating Angles

If the transmission operating angle is more than 12°, improper lubrication will occur. The operating angle is the transmission
mounting angle in the chassis plus the percent of upgrade (expressed in degrees).
For operating angles over 12°, the transmission must be equipped with an oil pump or cooler kit to insure proper lubrication.
Operating Temperatures with Oil Coolers

The transmission must not be operated consistently at temperatures above 250°F. However, intermittent operating temperatures
to 300°F do not harm the transmission. Operating temperatures above 250°F increases the lubricant’s oxidation rate and shortens
its effective life. When the average operating temperature is above 250°F, the transmission can require more frequent oil changes
or external cooling.
The following conditions in any combination can cause operating temperatures of over 250°F:
a. Operating consistently at slow speeds.
b. High ambient temperatures.
c. Restricted air flow around transmission.
d. Exhaust system too close to transmission.
e. High horsepower operation.
External oil coolers are available to reduce operating temperatures when the above conditions are encountered.
16
Lubrication / Application Information
Oil Cooler Chart
Transmission Oil Coolers are:

Recommended
With engines of 350 H.P. and above
Required
-With engines 399 H.P. and above and GCW’s over 90,000 lbs.
-With engines 399 H.P. and above and 1400 lb.ft or greater torque.
-With engines 450 H.P and above.
17
Preventative Maintenance
Everyday there are countless vehicles operating over the highways with transmissions in such a neglected mechanical condition,
they can be referred to as failures looking for a place to break down. They lack a proper and organized preventive maintenance
program.
Preventive maintenance is a general term which applies to all procedures necessary to have maximum life and satisfactory ser-
vice at the lowest possible cost, short of removing and repairing the unit.
A number of conditions contrary to good preventive maintenance can generally be pointed to when inspecting a failed transmis-
sion. Taking a few minutes every so many hours or miles to do a few simple checks could help avoid eventual breakdown or
reduce the repair cost. If the transmission is not cared for, it will breakdown.
Checks Before Transmission Removal
1. Air System and Connections
Check for leaks, worn air lines, loose connections and capscrews. See SERVICING AIR SYSTEM.
2. Clutch Housing Mounting
Check all capscrews of clutch housing flange for looseness.
3. Clutch Release Bearing (Not Shown)
Remove hand hole cover and check radial and axial clearance in release bearing.
Check relative position of thrust surface of release bearing with thrust sleeve on push-type clutches.
4. Clutch Pedal Shaft and Bores
Pry upward on shafts to check wear.
If excessive movement is found, remove clutch release mechanism and check bushings on bores and wear on shafts.
See OEM literature.
5. Lubricant
Change at specified service intervals.
Use only the types and grades as recommended. See LUBRICANTS.
6. Filler and Drain Plugs
Remove filler plugs and check level of lubricant at specified intervals. Tighten fill and drain plugs securely.
7. Capscrews and Gaskets
Check all capscrews, especially those on PTO covers and rear bearing covers for looseness which would cause oil leak-
age.
Check PTO opening and rear bearing covers for oil leakage due to faulty gasket.
8. Gear Shift Lever
Check for looseness and free play in housing. If lever is loose in housing, proceed with Check No. 9.
9. Gear Shift Lever Housing Assembly
Remove air lines at slave valve and remove the gear shift lever housing assembly from the transmission.
Check the tension spring and washer for set and wear.
Check the gear shift lever spade pin and slot for wear.
18
Check bottom end of gear shift lever for wear and check slot of yokes and blocks in shift bar housing for wear at contact
points with shift lever.
Checks With Drive Line Dropped
10. Universal Joint Companion Flange or Yoke Nut
Check for tightness. Tighten to recommended torque.
11. Output Shaft
Pry upward against output shaft to check radial clearance in mainshaft rear bearing.
Checks With Universal Joint Companion Flange or Yoke Removed.
NOTE:If necessary, use solvent and shop rag to clean sealing surface of companion flange or yoke. Do not use crocus
cloth, emery paper, or other abrasive materials that will mar surface finish.
12. Splines on Output Shaft
Check for wear from movement and chucking action of the universal joint companion flange or yoke.
13. Mainshaft Rear Bearing Cover
Check oil seal for wear.
19
Inspection
Table 1:
Part to inspect What to Check For Action to be Done

Speedometer Con- Speedometer cables should not be loose. Should Applied hydraulic thread sealant #71208 to
nections be an O-Ring or gasket between the mating threads. Torque speedometer sleeve to 35-50
speedometer sleeve and the rear bearing cover. Lbf-ft. Replace the O-ring/gasket if damaged or
missing.
Rear Bearing Cover Check retaining capscrews for tightness. Verify Apply Eaton Sealant #71205 to the capscrew
capscrews, Gasket, nylon collar and gasket are installed at the cham- threads. Torque capscrews to 35-45 Lbf-ft.Use
and Nylon Collar fered hole, aligned near the mechanical speedom- new parts if need to replace. Apply Eaton Sealant
eter opening. Verify that a rear bearing cover #71205 to the capscrew threads. Torque cap-
gasket is in place. screws to 35-45 Lbf-ft. Install a new gasket if
rear bearing cover was removed.
Output Yoke Retain- Check the output yoke retaining nut for tightness. Torque the output yoke retaining nut to 450-500
ing Nut Lbf-ft. Do not over torque nut.
PTO Covers and Check the capscrews for tightness. Apply Eaton Sealant #71205 to the capscrew
Openings threads. Tighten 6 bolt PTO capscrews to 35-45
Lbf-ft. Tighten 8 bolt PTO capscrews to 50-65
Lbf-ft.
Grey Iron Parts Check front bearing cover, front case, shift bar Replace parts found to be damaged.
housing, rear bearing cover, and clutch housing
for cracks or breaks.
Front Bearing Cover Check return threads for damage. Check the cap- If threads damaged, replace the input shaft.
screws for tightness. Tighten the capscrews to 35-45 Lbf-ft.
Oil Cooler and Oil Fil- Check all connections, fittings, hoses, and filter el- Tighten any loose fittings.
ter ement for tightness.
Oil Drain Plug, Oil Fill Check the oil drain plug and the oil fill plug for Torque the drain plug to 45-55 Lbf-ft. Torque the
Plug leakage. oil fill plug to 60-70 Lbf-ft.
20
Oil Leak Inspection Process

Inspect for Oil Leak
Determine if it is a Weep or a Leak
Weep: Stained, damp, no drips, light oil film, Leak: Extremely wet or dripping of oil in the
dirt adhered to the contaminated area. contaminated area.
Gasket Rear Seal Leak
Step 1
1. Clean suspected oil weep 1. Do not repair: Rear seal is 1. Determine the origin of the leak path.
area with a clean dry cloth designed to allow minimal 2. If origin of leak is obvious skip to Step 3.
or mild soluble degreaser. seepage (refer to Roadranger 3. If the origin of the oil leak is not obvious then
TCSM-0912 Seal Maintance use either of the two following steps to determine
2. Ensure lube is to proper Guide). the oil leak:
level.
2. Ensure lube is to proper Note: Do not use a high pressure spray washer to
3. Notify the customer that it level. clean the area. Use of a high pressure spray may
is only a weep and it is not force contamination into the area of concern and
considered to be detrimental temporarily disrupt the leak path.
to the life of the transmission.
i. Clean area with a clean dry cloth or mild
4. Repair is complete. soluble degreaser and fill the transmission to
the proper lube level.
OR
ii. Clean the area as noted above and insert tracer
dye into the transmission lube and fill
transmission to proper lube level.
Step 2
Operate vehicle to normal transmission operating
temperature and inspect the area for oil leak(s)
visually or if tracer dye was introduced use an UVL
(Ultraviolet Light) to detect the tracer dye’s point
of origin.
Note: When inspecting for the origin of the leak(s)
make sure the assumed leak area is not being
contaminated by a source either forward or above
the identified area such as the engine, shift tower,
shift bar housing, top mounted oil cooler, etc...
Step 3
Once the origin of the leak is identified, repair the
oil leak using proper repair procedures from the
designated model service manual.
Step 4
After the repair is completed, verify the leak is
repaired and operate the vehicle to normal
transmission operating temperature.
Inspect repaired area to ensure oil leak has been
eliminated. If the leak(s) still occurs, repeat steps
or contact the Roadranger Call Center at
1-800-826-4357.
21
How to Disassemble the External Parts
How to Disassemble the External Parts
EXTERNAL
PARTS
AIR Clutch
SYSTEM Housing
External Parts
CHANGING THE
INPUT SHAFT
AIR LINES
AUXILIARY
AND HOSES
SECTION
AIR FILTER/ ROADRANGER OUTPUT YOKE/

REGULATOR VALVE COMPANION
FLANGE
GEAR SHIFT
LEVER LEGEND
OPTIONAL PATH
TYPICAL PATH
SHIFT BAR
HOUSING
22
How to Assemble the External Parts
How to Assemble the External Parts

EXTERNAL
PARTS
OUTPUT YOKE/ CLUTCH CHANGING THE

COMPANION HOUSING INPUT SHAFT
FLANGE
AUXILIARY SHIFT BAR

SECTION HOUSING
AIR GEAR SHIFT

SYSTEM LEVER
AIR/FILTER ROADRANGER
REGULATOR VALVE
AIR LINES
AND HOSE
LEGEND
OPTIONAL PATH
TYPICAL PATH
23
Air System
How to Remove the Air Lines and Hose
Special Instructions
Before removing the air lines and hose, label or record their location.
If, after you remove the air lines and hoses, you are unsure of their location, see the Air System “Troubleshooting/Operation
Guide” TRTS-0920.
Special Tools
• Typical Service Tools
• For “push-to-connect” fittings, we recommend Eaton service tool kit K-2394. The kit contains the release tool and the
tubing cutter.
External Parts
Procedure -
1. Disconnect all air lines and hose.
2. Inspect the air lines and hose.
3. Inspect air fittings, remove if damaged.
24
Air System
How to Install the Air Lines and Hose
Make sure air lines and hose are not damaged.
Install the air lines and hose at their proper location.
All externally threaded 1/8" or 5/32" air lines and pipe fittings that are not coated with pre-applied thread sealant must be coated
with Eaton sealing material #71209 or equivalent for at least 5 complete and consecutive threads.
All externally threaded 1/4" air fittings that are not coated with pre-applied thread sealant must be coated with Eaton sealing ma-
terial #71209 or equivalent for at least 3 complete and consecutive threads.
For the 1/4" I.D. air hoses, install the fixed nut end first.
To install the air lines and hose, the air filter/regulator must be in position.
If you are unsure of the air lines and hose location, see the Air System “Troubleshooting/Operation Guide” TRTS-0920.
Special Tools
• For ‘push-to-connect’ fittings, we recommend Eaton “Service Tool Kit” K-2394. The kit contains the release tool and a
tubing cutter.
Procedure -
1. Replace removed air fittings.
2. Connect all removed air lines and hose.
Final Check
• Make sure fittings are tight.
• Make sure air lines are not kinked.
25
Air System
How to Remove the Air Filter/Regulator
The air filter/regulator has two (2) O-rings located between the filter/regulator and the range cylinder cover.
Special Tools
Procedure -
1. From the air filter/regulator, remove the two (2) capscrews.
External Parts
2. From the range cylinder cover, remove the two (2) O-rings.
3. Inspect the O-rings for cracks or distortion.
26
Air System
How to Install the Air Filter/Regulator
The air filter/regulator has two (2) o-rings located between the filter/regulator and the auxiliary section.
Special Tools
Procedure -
1. On the range cylinder cover, position the two (2) o-rings.
2. Over the o-rings, position the air filter/regulator.
3. Apply eaton/fuller sealant #71205 or equivalent to the two

(2) retaining capscrews.
4. Install the two (2) retaining capscrews, tighten to 8-12 lb-ft

of torque.
Final Check
• Make sure the capscrews are properly torqued.
27
Air System
How to Remove a Roadranger Valve
The air lines must be depressurized.
Special Tools
Procedure -
1. From the Roadranger valve cover, remove the two (2)

mounting screws.
External Parts
2. Slide the Roadranger valve cover down.
3. From the air fittings, disconnect the air lines.
4. From the Roadranger base, loosen the jam nut. Rotate the
Roadranger valve until the valve is removed.
5. Inspect the parts: nut, valve cover, air lines, sheathing, and
O-rings from the lever shaft.
6. On the Roadranger valve, inspect the air fittings; remove if

damaged.
28
Air System
How to Install a Roadranger Valve
To position the Roadranger valve: the range lever must be to the front or the splitter button to the left when facing forward.
Special Tools
Procedure -
1. Make sure the nut, valve cover, air lines, sheathing, and O-
rings are in position on the lever shaft.
2. If previously removed, replace the air fittings.
3. Place the Roadranger valve on the lever shaft and rotate into
position.
4. From the Roadranger valve bottom, tighten the jam nut.
5. Connect the air lines to the air fittings.
6. Slide the cover into position on the Roadranger valve.
7. Install the Roadranger valve cover two (2) mounting screws.

Final Check
• Make sure the air lines are seated fully
29
Air System
How to Remove the Range Actuator Valve
Special Tools
Procedure -
1. From the mounting screws, bend the lockwasher retaining

tabs down.
External Parts
2. From the range actuator valve bracket, remove the two (2)
mounting screws. The newest design of the range actuator
does not have the bracket.
3. Remove the range actuator valve lockwasher, bracket, and

range actuator valve.
4. Inspect the air fittings, remove if damaged.
5. From the range actuator valve bore, remove the actuating

pin.
6. Inspect the actuating pin for damage, replace if necessary.
30
Air System
How to Install the Range Actuator Valve
Apply Eaton lubricant #71214 or equivalent to the O-ring so a film covers the entire surface of each O-ring.
Special Tools
Procedure -
1. Install the actuating pin in the range actuator valve bore.
2. If previously removed, replace the air fittings
3. Install the range actuating valve.
4. Position the range actuating valve bracket and lockwasher

over the capscrew openings. The newest design of the
range actuator does not have the bracket.
5. Apply Eaton sealant #71205 or equivalent to the retaining

capscrews.
31
Air System
6. Install the retaining capscrews, tighten to 8-12 lb-ft of

torque.
7. Bend the retaining tabs on the lockwasher up.

Final Check
External Parts
32
Air System
How to Remove the Top 2 Valve Assembly
Special Tools
Procedure -
1. From the 3-way connector, disconnect the wire harness.
2. From the air fittings, disconnect the air lines.
3. From the Top-2 valve assembly, remove the two (2) cap-
screws.
33
Air System
How to Install the Top 2 Valve Assembly
Special Tools
Procedure -
1. Install the two (2) retaining capscrews, tighten to 35-45 lb-

ft of torque.
External Parts
2. Connect the air lines to the air fittings.
3. Connect the 3-way connector to the harness.
34
Shift Bar Housing
How to Remove the Gear Shift Lever
The air lines must be disconnected from the transmission or from the Roadranger valve.
Remote control housings are removed the same way as gear shift levers.
Special Tools
Procedure -
1. From the gear shift lever base, remove the four (4) retaining
capscrews.
2. To break the gasket seal, lightly jar the gear shift housing.
3. Remove the gear shift lever housing.
4. Remove the gasket and clean all mounting surfaces of gas-

ket material.
35
Shift Bar Housing
How to Install the Gear Shift Lever
Remote control housings are installed the same way as gear shift levers.
For standard and forward shift bar housings, make sure the two (2) balls and tension springs are in the shift bar housing top bores.
Make sure the shift block and yoke notches are aligned in the neutral position.
Special Tools
Procedure -
External Parts
1. Position a new gear shift lever gasket on the gear shift lever
mounting surface.
2. Fit the gear shift lever into the shift block.
3. Apply Eaton/Fuller Sealant #71205 or equivalent to the re-

taining capscrews.

torque.
Final Check
• Make sure you can shift the transmission.
36
Shift Bar Housing
How to Remove the Shift Bar Housing
Before removing the shift bar housing, the air lines must be disconnected.
For models equipped with an oil pump and/or cooler assemblies, make sure to disconnect the lube line connected to the shift bar
housing.
There are two (2) sizes of capscrews. The 1½" capscrews are used with the lifting eyes. Note their location.
Special Tools
Procedure -
1. From the shift bar housing rim, remove the retaining cap-
screws.
2. From the alignment stud, remove the nut and washer.
3. To break the gasket seal, jar the shift bar housing.
4. Remove the shift bar housing.

ket material.
6. If the two (2) sets of tension springs and balls from the
housing top bores are loose, tilt the assembly and remove
them. The anti-rotating pin can be removed also. Newer shift
bar housings do not have the anti-rotating pin.
37
Shift Bar Housing
How to Install the Shift Bar Housing
There are two (2) sizes of capscrews. The 1½" capscrews are used with the lifting eyes.
Special Tools
Procedure -
1. Place the shift bars in the neutral position.
2. Place the mainshaft sliding clutches in the neutral position.
External Parts
3. Position a new shift bar housing gasket on the shift bar
housing mounting surface.
4. As you install the shift bar housing, make sure the yokes fit
into the corresponding clutch gears slots.

taining capscrews.

torque.
7. Install the washer and nut on the alignment stud.
Final Check
38
Output Yoke/Companion Flange
How to Remove the Output Yoke/Companion Flange
You must remove the shift bar housing in order to lock the transmission.
For proper cleaning and maintenance, see TCSM-0912 “Seal Maintenance Guide”.
After removal of the output yoke/companion flange, temporarily replace the output shaft nut to protect the output shaft threads
during auxiliary section disassembly.
Special Tools

• A large breaker bar or air impact wrench
Procedure -
1. Engage two (2) mainshaft sliding clutches into two (2)

mainshaft gears to lock the transmission.
2. Use a large breaker bar or air impact wrench to remove the

output shaft nut.
3. Pull the yoke or flange straight to the rear and off the output
shaft.
39
Output Yoke/Companion Flange
How to Install the Output Yoke/Companion Flange
You must remove the shift bar housing in order to lock the transmission.
For proper cleaning and maintenance, see TCSM-0912 “Seal Maintenance Guide”.
Special Tools
• Torque Wrench 500 lb-ft Capacity
Procedure -
External Parts
1. Engage two (2) mainshaft sliding clutches into two (2) main-
shaft gears to lock the transmission.
2. Install the speedometer drive gear rotor or replacement

spacer on the output shaft inside the rear bearing cover.
3. If the slinger on the yoke is damaged, replace using a Sling-

er/Seal kit.
4. Slide the companion flange or yoke onto the output shaft.
5. Install the output shaft nut, tighten to 450-500 lb-ft of

torque.
Final Check
• Make sure the output shaft nut is properly torqued.
• Unlock the transmission.
40
Auxiliary Section
How to Remove the Auxiliary Section Without Tapered Bearings
There can be different capscrew lengths, note their location.
Auxiliary sections can be removed either with the transmission in the horizontal position or the vertical position.
Special Tools

• An auxiliary section hanger bracket for horizontal removal
• A steel bar longer than the width of the output yoke for vertical removal
• A hoist with a lifting chain
Procedure - To remove the auxiliary section in the

horizontal position.
1. From the auxiliary section housing, remove the retaining

capscrews that attach the front section to the auxiliary sec-
tion.
2. Insert the two (2) longest capscrews in the housing flange

tapped holes. Tighten evenly to move the auxiliary section
away from the front box. Go far enough to break the gasket
seal.
41
Auxiliary Section
3. Remove the capscrews from the tapped holes.
4. Attach an auxiliary section hanger bracket to the auxiliary

section top.
5. Attach a lifting chain to the auxiliary section hanger bracket.
6. Move assembly to the rear until auxiliary section is free.

ket material.

vertical position.
External Parts
1. With blocks under the clutch housing to prevent input shaft
damage, place transmission in the vertical position, clutch
housing down.

capscrews that attach the front box to the auxiliary section.
3. Install a steel bar through the yoke.
4. Attach a lifting chain to the steel bar.
5. Lift assembly from the front section.

ket material.
42
Auxiliary Section
How to Install the Auxiliary Section Without Tapered Bearings
There are different capscrew lengths, install in the correct location.
Auxiliary sections can be installed either with the transmission in the horizontal position or the vertical position.
To install in the vertical position, the clutch housing must be installed.
Special Tools
Procedure - To install the auxiliary section in the hor-

izontal position.
1. Position a new gasket on the transmission mounting sur-

face.

section top.
4. Position the auxiliary section on the two (2) dowel pins.
5. Slide the auxiliary section on until the hanger bracket con-

tacts the front case back.
6. Remove the auxiliary section hanger bracket.
7. Slide the auxiliary section the rest of the way into position.

taining capscrews.

torque.
43
Auxiliary Section
Procedure - To install the auxiliary section in the ver-

tical position.

damage, place the transmission in the vertical position,
clutch housing down.

face.
5. Position the auxiliary section over the two (2) dowel pins.
External Parts
6. Slide the auxiliary section down the dowels.

taining capscrews.

torque.
9. Remove the steel bar and chain.
Final Check
• Make sure capscrews are properly torqued.
• Make sure the input shaft rotates.
44
Auxiliary Section
How to Remove the Auxiliary Section With Tapered Bearings
There can be different capscrew lengths, note their location.
Auxiliary sections can be removed either with the transmission in the horizontal position or the vertical position.
Auxiliary countershaft retaining straps may be installed to hold the countershafts in place. Auxiliary can be removed without straps,
use caution.
Special Tools
• Auxiliary countershaft retaining straps

horizontal position.
1. Remove the four (4) capscrews and the auxiliary counter-

shaft rear bearing cover, gasket, and rear bearing shim.
2. Install the auxiliary countershaft retaining straps with 2-3/8"

NC x 1" and 1-3/8" NC x 2-1/2" clean cap-screws.
WARNING: Do not use an air gun. Tighten by hand until the

capscrews are snug.
45
Auxiliary Section

capscrews that attach the front section to the auxiliary sec-
tion.
4. Insert the two (2) longest capscrews in the housing flange

tapped holes. Tighten evenly to move the auxiliary section
away from the front box. Go far enough to break the gasket
seal.
5. Remove the capscrews from the tapped holes.

section top.
8. Move assembly to the rear until auxiliary section is free.
External Parts
ket material.
Procedure - To remove the auxiliary section in the ver-

tical position.

damage, place transmission in the vertical position, clutch
housing down.
2. Remove the four (4) capscrews and the auxiliary counter-

shaft rear bearing cover, gasket, and rear bearing shim.
3. Install the auxiliary countershaft retaining straps with 2-3/8"

NC x 1" and 1-3/8" NC x 2-1/2" clean capscrews.

capscrews are snug.
46
Auxiliary Section

capscrews that attach the front box to the auxiliary section.
7. Lift assembly from the front section.

ket material.
47
Auxiliary Section
How to Install the Auxiliary Section With Tapered Bearings
There are different capscrew lengths, install in the correct location.
Auxiliary sections can be installed either with the transmission in the horizontal position or the vertical position.
To install in the vertical position, the clutch housing must be installed.
Special Tools
External Parts
Procedure - To install the auxiliary section in the hor-

izontal position.

face.

section top.
4. Position the auxiliary section on the two (2) dowel pins.
5. Slide the auxiliary section on until the hanger bracket con-

tacts the front section back.
6. Remove the auxiliary section hanger bracket.
7. Slide the auxiliary section the rest of the way into position.

taining capscrews.

torque.
10. To finish installation, see "The Shimming Procedure for Ta-

pered Bearings".
48
Auxiliary Section
Procedure - To install the auxiliary section in the ver-

tical position.

damage, place the transmission in the vertical position,
clutch housing down.

face.
5. Position the auxiliary section over the two (2) dowel pins.
6. Slide the auxiliary section down the dowels.

taining capscrews.

torque.
9. Remove the steel bar and chain.
10. To finish installation, see "The Shimming Procedure for Ta-

pered Bearings".
Final Check
49
Auxiliary Section
The Shimming Procedure For Tapered Bearings
The shimming procedure can be done in the horizontal or vertical position. The procedure is done the same.
Shims must be aligned properly or else the rear bearing cover may be damaged when final torque is applied.
Special Tools
Procedure -
1. Remove the countershaft straps. Make sure a 0.125 coun-
External Parts
tershaft rear bearing shim is installed. Be sure the counter-
shaft rear bearing races are seated in the bearing bores.
2. Install two (2) clean 3¦8" x 1" capscrews without washers di-
rectly across from each other in each bearing cover. Tapped
holes in auxiliary case must be free of thread adhesive.
3. Tighten the capscrews to 7 Lbf·in of torque. Do not install

the countershaft rear bearing cover gasket.
50
Auxiliary Section
4. Rotate the output shaft six (6) times clockwise, then six (6)
times counterclockwise to seat the countershaft rear bear-
ings. Use a feeler gauge, as close to each capscrew location
as possible, and measure the gap between the countershaft
rear bearing cover and the auxiliary case. Record the mea-
surements. Using the average measurement, refer to the
shimming chart to identify the proper shim.
5. Remove the countershaft rear bearing cover and gauging

shim.
6. Place the selected shim on the rear countershaft bearing

race.
7. Position a new gasket on countershaft rear bearing cover

mounting surface.
8. Position the countershaft rear bearing cover over the new

gasket.

taining capscrews.

torque.
11. Repeat Steps 1-8 for the other countershaft rear bearing
cover.
Final Check
Table 1:
Feeler
Standard Oil Pump
Gauge Shim
Shim Part Shim Part Color Code
Average Thickness
number Number
Gap
.088-.089 .042-.043 21454 21474 Brown
.085.0875 .045-.046 21455 21475 Tan
51
Auxiliary Section
Table 1:
Feeler
Standard Oil Pump
Gauge Shim
Shim Part Shim Part Color Code
Average Thickness
number Number
Gap
.082-.0845 .048-.049 21456 21476 Orange
.079-.0815 .051-.052 21457 21477 Yellow
.076-.0785 .054-.055 21458 21478 Green
.073-.0755 .057-.058 21459 21479 Light Blue
.070-.0725 .060-.061 21460 21480 Lavender
External Parts
.067-.0695 .063-.064 21461 21481 White
.064-.0665 .066-.067 21684 21686 Black
.061-.0635 .069-.070 21685 21687 Silver
.058-.0605 .072-.074 21452 + 21452 21472 + 21472 Red + Red
.055-.0575 .075-.077 21452 + 21453 21472 + 21473 Red + Pink
.052-.0545 .078-.080 21452 + 21454 21472 + 21474 Red + Brown
.049-.0515 .081-.083 21452 +21455 21472 + 21475 Red + Tan
.046-.0485 .084-.086 21452 + 21456 21472 + 21476 Red + Orange
.043-.0455 .087-.089 21452 + 21457 21472 + 21477 Red + Yellow
.040-.0425 .090-.092 21452 + 21458 21472 + 21478 Red + Green
.038-.0395 .093-.095 21452 + 21459 21472 + 21479 Red + Lt. Blue
52
Clutch Housing
How to Remove the Clutch Housing
Removal of the clutch housing is done in the horizontal position.
Special Tools
Procedure -
1. From inside the clutch housing, remove the nuts and wash-
ers.
2. From inside the clutch housing, remove the bolts.
3. Jar clutch housing to break gasket seal.
4. Pull the clutch housing from the studs and transmission

case.

ket material.
53
Clutch Housing
How to Install the Clutch Housing
Installation of the clutch housing is done in the horizontal position.
Special Tools
Procedure -
1. Position a new gasket on the housing mounting surface.
2. Install the clutch housing on the front box, pilot it on the six
External Parts
studs and drive gear bearing cover.
3. Install the nuts with washers or lockwashers on the studs,

tighten to 180-190 lb-ft of torque.
4. Install the capscrews with lockwashers, tighten to 90-100

lb-ft of torque.
Final Check
54
Changing The Input Shaft
How to Remove the Input Shaft Without Disassembling the Transmission
Remove the transmission from the vehicle.
Special Tools
Procedure -
1. Remove the front bearing cover and gasket.
2. Remove the input shaft snap ring.
3. Drive the input shaft towards the transmission rear, through

the bearing as far as possible.
4. Pull the input shaft forward to expose the bearing snap ring.
5. To complete bearing removal, use pry bars.
6. From the drive gear front, remove the drive gear spacer.
55
7. Remove the drive gear snap ring.
8. Pull the input shaft forward, out of the drive gear and trans-
mission case.
External Parts
56
How to Install the Input Shaft Without Disassembling the Transmission
Check the bushing in the input shaft pocket, replace if worn.
Special Tools
• Input Shaft Bearing Driver
Procedure -
1. Install the new input shaft into main drive gear splines.
2. Position the input shaft just far enough into the gear to ex-
pose the drive gear I.D. snap ring groove.
3. Install the drive gear I.D. snap ring.
4. Install the drive gear spacer on the input shaft.
5. With the external snap ring to the outside, slide the drive
gear bearing on the input shaft and position into the case
bore.
57
6. With the input shaft bearing driver, seat the bearing.
7. Install the bearing retainer snap ring.

face.
External Parts
9. Position the front bearing cover on the input shaft, align the
oil return hole in the cover with the oil return hole on the
case.
10. Apply Eaton/Fuller sealant #71205 or equivalent to the re-

taining capscrews.

torque.
Final Check
• Make sure the input shaft turns freely.
58
Functions of a Shift Bar Housing
Shift Bar Housing Identification

Shift bar housings are a very important part of the transmission. No matter what kind of shift bar housing your transmission has,
they all provide the same functions
• Engage the transmission gearing.
• Prevents the driver from shifting into 2 gears at the same time.
• Prevents shifting into reverse without force.
• Actuates the back up lights.
• Actuates the neutral switches.
Standard Shift Bar housing
Forward Shift Bar Housing w/SUPER 10 on cover
Standard Shift Bar Housing w/SUPER 10 on cover
59
Functions of a Shift Bar Housing
New Forward Shift Bar Housing w/SUPER 10 on cover
Shift Bar Housing
60
Gear Shift Lever
How to Disassemble the Gear Shift Lever
If total disassembly is needed, the Roadranger valve must be removed first.
Release the spring one coil at a time.
Special Tools
• A vise with brass jaws or wood blocks
Procedure -
1. Slide the Boot up the shift lever shaft and remove
2. With housing bottom facing up, secure the assembly in a

vise.
3. Use large screwdriver to twist between the spring and hous-

ing, forcing the spring from under the housing lugs.
4. From inside the housing tower, remove the tension spring,

washer, and gear shift lever.
5. In models so equipped, from the housing bore, remove the

nut and washer.
61
Gear Shift Lever
6. From the housing tower spade pin bore, remove and inspect
the spade pin, discard if damaged.
7. From the housing tower inside groove, inspect the O-ring,

discard if damaged.
Shift Bar Housing
62
Gear Shift Lever
How to Assemble the Gear Shift Lever
Inspect tension spring and washer for wear.
Apply Eaton rust preventative lubricant #71212 or equivalent to the shift lever pivot ball. A rust preventative lubricant film should
cover all surfaces between and including the pivot ball.
Seat the tension spring one coil at a time.
Special Tools
• Tension Spring Driver
Procedure -
1. With housing bottom facing up, secure the assembly in a

vise.
2. If the spade pin is damaged, replace and install the spade pin
in housing tower bore.
3. In models so equipped, install the nut and washer in the

housing bore.
4. If the O-ring is damaged, replace; lubricate the O-ring with

Eaton/Fuller lubricant #71206 or equivalent. Install the O-
ring in the housing tower inside groove.
5. Align the lever ball slot with the spade pin and position the
gear shift lever in the housing tower.
6. With dished-side up, install the washer over the ball.
63
Gear Shift Lever
7. Use a tension spring driver to install the tension spring un-

der the housing lugs.
8. Remove the assembly from the vise.
9. Install a rubber boot over the gear shift lever and against the
housing.
Final Check
• Make sure the gear shift lever can move.
Shift Bar Housing
64
Shift Bar Housing
How to Disassemble the Standard Shift Bar Housing
The shift bar housing must be removed from the transmission.
During disassembly, lay all parts on a clean bench in order of removal to facilitate assembly.
Shift bars not being removed must be kept in the neutral position or the interlocking parts lock the bars.
Start with the bottom shift bar.
Cut the lockwire and remove the lockscrews from each bar just before their removal.
Special Tools
Procedure -
1. If the two (2) sets of tension springs and balls from housing
bores and the anti-rotating pin have not been removed, place
the shift bar housing on its side to remove them.
2. With the housing rear to the right, lay the assembly on a flat
surface. If installed, remove the oil trough retaining cap-
screws and oil trough.
3. While removing the bottom yoke bar, remove the shift yoke.
65
Shift Bar Housing
4. While removing the top yoke bar, remove the shift yoke as-
sembly and block assembly.
5. Remove the interlock pin.
6. From the middle yoke bar, remove the jam nut, plain nut, and
washer.
Shift Bar Housing

7. Remove the range interlock bar.
8. From the middle yoke bar, remove the select interlock bar to
the right.
9. Pull the select tube to the left and remove the shift select
block.
66
Shift Bar Housing
10. Remove the select tube with key to the left.
11. From the 1st & reverse shift yoke, remove the snap ring,
washer, spring, and plunger. From the 3rd speed block, re-
move the plug, spring, and plunger.
12. Inspect the yoke or block parts, replace the worn parts.
67
Shift Bar Housing
How to Assemble the Standard Shift Bar Housing
Inspect shift blocks and shift yokes for wear.
Apply Eaton sealant #71208 or equivalent to the shift bar housing plugs which are used to plug oil cooler provision holes. The
sealant should be applied so that at least 5 complete threads are covered.
Apply Eaton lockwire #1819 or equivalent to all shift bar housing assembly set screws in both blocks and yokes. The wire should
anchor the capscrew at least 2 complete 360° turns. The lockwire ends should be trimmed and bent out of the way of any part
interference.
Keep yoke bars in neutral while assembling.
Special Tools
Procedure -
Shift Bar Housing

1. Assemble the 1st & reverse shift yoke assembly:
a. Install the plunger in the 1st & reverse shift yoke bore,
plunger shank to the outside.
b. Install the spring into the bore over the plunger shank.
c. Position the washer over the plunger shank.
d. Install the snap ring.
2. Assemble the 3rd speed block assembly:

a. Install the plunger in the 3rd shift block bore, plunger
shank to the outside.
c. Install the plug and tighten to compress the spring.
d. After plug bottoms out, back the plug out 1-11/2 turns.
e. Complete the block assembly process by staking the
plug through the small hole in block.
68
Shift Bar Housing
surface.
4. Install the select tube in the middle boss with key in the key
slot.
5. As the select tube passes through the first boss, install the
shift select block.
6. From the right, install the select interlock bar.
7. Install the range interlock bar, chamfered end in, notched

side down.
8. At the middle yoke bar front end, install the washer, plain
nut, and jam nut.
69
Shift Bar Housing
9. Install the interlock pin, centered between bosses.
10. While installing the top yoke bar, position the shift yoke as-
sembly and block assembly. The block assembly aligns with
shift select block ear.
11. Install the lockscrews, tighten to 35-45 lb-ft of torque. Lock-

wire securely.
12. While installing the bottom yoke bar, position the shift yoke.
The block assembly aligns with shift select block ear.
13. Install the lockscrew, tighten to 35-45 lb-ft of torque. Lock-

wire securely.
14. Turn the shift bar housing over, and install the anti-rotating
pin and the two (2) sets of tension springs and balls.
Final Check
Shift Bar Housing

• Make sure interlocking system is working – can’t shift
into 2 gears at the same time.
• Make sure all capscrews are lockwired.
• Make sure the anti-rotating pin and the two (2) sets of
tension springs and balls are installed.
70
Shift Bar Housing
How to Disassemble the Standard Shift Bar Housig (w/Super 10 on cover)
Special Tools
Procedure -
bores have not been removed, place the shift bar housing on
its side to remove them.
2. If installed, remove the oil trough retaining capscrews and

oil trough.
surface.
71
Shift Bar Housing
Shift Bar Housing

7. From the middle yoke bar, drive center block roll pin out.
8. Pull the center bar to the right and remove the shift select
block.
72
Shift Bar Housing
73
Shift Bar Housing
How to Assemble the Standard Shift Bar Housing (w/Super 10 on cover)
interference.
Special Tools
Procedure -
Shift Bar Housing


74
Shift Bar Housing
surface.
4. Install the center rail in the middle boss.
5. As the center rail passes through the first boss, install the
shift block.
6. Drive the center block roll pin through the center bar to hold
the center block in position.

wire securely.
75
Shift Bar Housing

wire securely.
12. Install the oil trough and oil trough retaining capscrews.
13. Turn the shift bar housing over, and install the two (2) sets
of tension springs and balls.
Final Check
• Make sure the two (2) sets of tension springs and balls
are installed.
Shift Bar Housing
76
Shift Bar Housing
How to Disassemble the Forward Shift Bar Housing (w/Super 10 on cover)
Special Tools
Procedure -
its side to remove them.

oil trough.
surface.
77
Shift Bar Housing
Shift Bar Housing

block.
78
Shift Bar Housing
79
Shift Bar Housing
How to Assemble the Forward Shift Bar Housing(w/Super 10 on cover)
interference.
Special Tools
Procedure -
Shift Bar Housing


80
Shift Bar Housing
surface.
shift block.

wire securely.
81
Shift Bar Housing

wire securely.
Final Check
are installed.
Shift Bar Housing
82
Shift Bar Housing
How to Disassemble the New Forward Shift Bar Housing (w/Super 10 on cover)
Special Tools
Procedure -
its side to remove them. Check the condition of the align-
ment pin, replace if necessary.

oil trough.
surface.
83
Shift Bar Housing
Shift Bar Housing

block.
84
Shift Bar Housing
85
Shift Bar Housing
How to Assemble the New Forward Shift Bar Housing (w/Super 10 on cover)
interference.
Special Tools
Procedure -
Shift Bar Housing


86
Shift Bar Housing
surface.
shift block.

wire securely.
87
Shift Bar Housing

wire securely.
Final Check
are installed.
Shift Bar Housing
88
Front Section
How to Disassemble the Front Section

FOLLOW THE SOLID LINE,
THEN THE DOTTED LINE,
REMOVE
THEN THE DASHED LINE
EXTERNAL
PARTS
DISASSEMBLE AUXILIARY
AUXILIARY DRIVE GEAR
DRIVE GEAR ASSEMBLY
MOVE
REVERSE
GEAR
UPPER REVERSE IDLER GEAR
REVERSE
IDLER GEAR
ASSEMBLY
REMOVE UPPER COUNTERSHAFT DISASSEMBLE
COUNTERSHAFT BEARINGS MAINSHAFT
BEARINGS
MAINSHAFT
ASSEMBLY
DISASSEMBLE
COUNTERSHAFT
UPPER
COUNTERSHAFT
LOWER COUNTERSHAFT BEARINGS

COUNTERSHAFT
LOWER COUNTERSHAFT ASSEMBLY LOWER REVERSSE IDLER GEAR
INPUT SHAFT
ASSEMBLY
89
How to Remove the Auxiliary Drive Gear Assembly
Before removing the auxiliary drive gear, the auxiliary section must be removed.
Special Tools
• Large pair of snap ring pliers
Procedure -
1. Remove the auxiliary bearing retainer ring capscrews.
2. Remove the mainshaft rear groove snap ring.
3. From inside the auxiliary drive gear assembly, remove the

splined washer.
4. Insert three (3) of the capscrews in the specially tapped

holes of the retainer ring.
5. Tighten the capscrews evenly to force the auxiliary drive

gear assembly from the case.
6. Remove the auxiliary drive gear from the mainshaft.
Front Section
7. From the mainshaft, remove the splined washer.
90
How to Remove the Reverse Idler Gear Assembly
The following instructions are used to remove upper and lower reverse idler gears.
Before the upper reverse idler gear assembly can be removed, mainshaft reverse gear must be positioned forward against the
next gear.
While removing the reverse idler shaft, the thrust washer can drop to the transmission case bottom.
The mainshaft reverse gear must be moved in order to remove the upper reverse idler gear, see “How to Remove the Mainshaft
Assembly”, steps 1-3.
Special Tools
• Jaw Pullers or Impact Puller
Procedure -
1. From the reverse idler gear bore, use inside jaw pullers or an
impact puller to remove the auxiliary countershaft front
bearing.
2. From the idler shaft, remove the loosened lock nut and
washer.
91
3. From the idler shaft rear, remove the pipe plug.
4. Install an impact puller, 1¦2"-13 threaded end, and remove

the shaft from case bore.
5. As the idler shaft and idler plate are removed, remove the
thrust washer and gear.
6. Inspect the reverse gear assembly, remove the inner race

and needle bearing, if damaged.
Front Section
92
How to Remove the Countershaft Bearings
The following instructions are used to remove the upper and lower countershaft bearings. To remove the mainshaft assembly,
only the upper countershaft bearings need to be removed.
Performing the following instructions will damage the bearings and should be not be done unless bearing replacement is planned.
The bearing inner race remains pressed on the countershaft after removal of the front bearings.
Special Tools
• Soft bar and a maul
• Bearing puller or pry bars
Procedure -
1. To keep the mainshaft pilot from falling out of the input shaft
pocket, temporarily install the auxiliary drive gear on the
mainshaft.
2. From each countershaft rear groove, remove the snap ring.
3. From inside the case, use a soft bar and maul to drive the
countershaft rear bearings from the case bores.
93
4. From the front of each countershaft, remove the capscrew

and front retainer plate.
5. Use the soft bar and maul to drive each countershaft to the
rear as far as possible. This partially unseats the front bear-
ings.
6. Return to the case rear, and drive each countershaft forward

as far as possible. This exposes the bearing snap rings.
7. Use a bearing puller or pry bars to remove the countershaft

front bearings. If a bearing puller is used, the front bearing
cover has to be removed.
Front Section
94
How to Remove the Mainshaft Assembly
Be careful when removing the mainshaft assembly, the sliding clutch on the end can slip off the mainshaft.
Reverse gear is also free and can fall off the shaft.
Special Tools
• Large hook or 3 foot piece of rope
Procedure -
1. From the mainshaft, remove the reverse gear retaining snap

ring.
2. Move the mainshaft reverse gear as far to the rear as possi-

ble and remove reverse gear I.D. snap ring.
3. Move the reverse gear forward and against the next gear, en-
gaging the mainshaft sliding clutch spline.
WARNING: If not removing the upper reverse idler gear as-

sembly, you must remove the upper reverse idler gear as-
sembly shaft and roll the gear to the outside, see “How to
Remove the Reverse Idler Gear Assembly”, steps 1-4.
4. Use a large screwdriver and block the upper countershaft as-

sembly against the case wall.
WARNING: If removing the upper reverse idler gear assem-

bly, see “How to Remove the Reverse Idler Gear Assembly”
at this time.
5. Position the hook or rope around the mainshaft.
6. Pull the mainshaft to the rear to free the pilot from the input
shaft pocket.
7. Tilt mainshaft front up and lift assembly from the case.
95
Expect for the PTO gears the upper and lower countershaft assemblies are the same. Make sure and mark each as they are re-
moved.
Special Tools
Procedure -
1. Move the upper countershaft assembly to the rear as far as

possible.
2. Swing the countershaft front to middle of the case.
3. Lift the countershaft assembly from the case.
Front Section
96
How to Remove the Input Shaft Assembly
None
Special Tools
Procedure -
1. If the front bearing cover is still installed, remove the six (6)
retaining capscrews and cover. Remove the any remaining
gasket material from the case and cover.
2. From the input shaft groove, remove the bearing retaining

snap ring.
3. Use a soft bar and maul and drive the input shaft toward the
case rear as far as possible. Pull the input shaft forward.
4. Use pry bars or screwdrivers to complete removal of the

bearing.
5. From the drive gear front remove drive gear spacer.
6. Remove the drive gear internal snap ring.
97
7. Pull the input shaft forward and out of the drive gear.
8. From inside the case, remove the drive gear.
9. Inspect the bushing in the input shaft pocket, remove if dam-

aged.
Front Section
98
Front Section
How to Assemble the Front Section

FOLLOW THE SOLID LINE,
THEN THE DOTTED LINE,
THEN THE DASHED LINE FRONT
BOX
LOWER REVERSE IDLER GEAR
REVERSE
UPPER REVERSE IDLER GEAR IDLER GEAR
ASSEMBLY
ASSEMBLE
COUNTERSHAFTS
LOWER COUNTERSHAFT
BEARINGS
COUNTERSHAFT
ASSEMBLIES
INSTALL
COUNTERSHAFT
BEARINGS
INPUT SHAFT ASSEMBLE
ASSEMBLY MAINSHAFT
ASSEMBLE
AUXILIARY
DRIVE GEAR
UPPER COUNTERSHAFT BEARINGS MAINSHAFT

ASSEMBLY
AUXILIARY
DRIVE GEAR
ASSEMBLY
99
How to Install the Reverse Idler Gear Assembly
If you install the bottom reverse idler gear assembly, make sure the three (3) magnetic discs are securely in place at case bottom.
Use Eaton Adhesive #71210 or equivalent.
Special Tools
Procedure -
1. If reverse gear assembly is disassemble, position the needle

bearing and inner race into the reverse idler gear.
2. Thread the pipe plug into the reverse idler shaft and tighten.
3. On the reverse idler shaft, position the idler shaft plate, flat
side to the front.
4. Insert the idler shaft into the case bore, threaded-end to the
front. As the shaft passes through the case bore position the
reverse idler gear on the shaft, long hub to the front. Insert
the thrust washer between the reverse idler gear and the
Front Section
case support boss. Finish inserting the idler shaft.
5. Make sure the reverse idler shaft is seated in the support

boss bore.
6. Install the washer and lock nut on shaft front. Tighten the
stop nut to 50-60 lb-ft of torque.
100
7. Use a bearing driver and a maul and install the auxiliary

countershaft front bearing outer race against the idler plate.
Final Check
• Make sure the stop nut is properly torqued.
• Make sure the bearing outer race is installed against the
idler plate.
101
Make sure the countershaft assemblies have been marked for proper position, 47-tooth PTO gear in the lower position.
On the drive gear of each countershaft assembly, mark the tooth aligned with the gear keyway and stamped with an “O” for easy
identification. A highly visible color of toolmaker’s dye is recommended for making timing marks.
Special Tools
• Toolmaker's dye
Procedure -
1. Mark the countershaft drive gear for timing purposes.
2. Place the lower, 47-tooth PTO gear, assembly in the case,
Front Section
the inner bearing race end to the front.
3. Position as far to the left as possible (the opposition side as

the lower reverse idler gear assemble.)
4. Place the upper, 45-tooth PTO gear, assembly in the case,

the inner bearing race end to the front.
5. Position as far to the right as possible (the same side as the

lower reverse idler gear assemble).
Final Check
• Make sure the upper and lower countershafts are in the
right place.
• Make sure the timing marks are visible.
102
How to Install the Countershaft Bearings
The front bearing inner race must be pressed on the countershaft front.
The flanged-end driver must cover the bearing outer race for proper installation.
Temporarily use the assembled auxiliary drive gear to hold the mainshaft in the input shaft pilot.
Special Tools
• Countershaft support tool
• Flanged-end driver and maul
Procedure -
1. Move the countershaft to the rear and insert the countershaft

support tool to center shaft in rear case bore.
2. Use a flanged-end driver to start the front bearing in case

bore.
103
3. Use a screwdriver inserted in the countershaft capscrew

bore to help center the countershaft.
4. Move the countershaft forward into the bearing.
5. Use a flanged-end bearing driver and maul to completely

seat the front bearing in case bore.
6. On the countershaft front, position the retainer plate with roll

pin in hole at shaft end.
7. Secure with capscrew, tightening to 90-120 lb-ft of torque.
8. From the rear, remove the countershaft support tool.
9. With the larger I.D. lead chamfer to the shaft front, use a
flanged-end bearing driver and install the rear bearing.
10. In the countershaft rear groove, install the rear snap ring.
Final Check
Front Section
• Make sure the front bearing capscrew is properly
torqued.
• Make sure the rear snap ring is in place.
104
How to Install the Input Shaft Assembly
As part of assembling the input shaft assembly, the mainshaft drive gear must be installed and timed.
Replace the pilot bushing, if worn.
Apply Eaton lubricant #71215 or equivalent to the pilot bushing so that a film of lubricant covers the entire internal surface of the
bushing.
Special Tools
• Toolmaker’s dye
Procedure -
1. In I.D. of main drive gear, install the snap ring.
2. Use toolmaker’s dye and mark the main drive gear for timing
purposes.
Mark any two (2) adjacent teeth on the drive gear. Repeat the
procedure for the two (2) adjacent teeth directly opposite the
first set marked.
3. Inside the case, mesh the lower countershaft drive gear

marked tooth with either set of marked teeth on the main
drive gear.
4. Slide the input shaft through the main drive gear.
105
5. Over the input shaft, install the drive gear spacer.
6. With the bearing external snap ring to the outside, position

the bearing on the input shaft.
7. Use a flanged-end driver and maul to seat the input shaft

bearing.
8. Temporarily install the front bearing cover.
9. From inside the case, use a soft bar and maul to drive the in-
put shaft through the bearing. Remove the front bearing
cover.
Front Section
10. Install the bearing retainer snap ring.
106
11. Position a new gasket on the bearing cover mounting sur-

face, making sure to align the gasket oil return hole with
case oil return hole.
12. Position the front bearing cover, making sure to align the
cover oil return hole with case oil return hole.
13. Secure the front bearing cover with six (6) capscrews, tight-
en to 35-45 lb-ft of torque.
Final Check
• Make sure the drive gear is timed with the lower Coun-
tershaft.
• Make sure the front bearing cover capscrews are tight-
en properly.
107
How to Install the Mainshaft Assembly
The lower countershaft bearings and the input shaft must be installed.
Check to make sure the lower countershaft drive gear marked tooth is in time with main drive gear set of marked teeth.
Special Tools
• A large hook or 3' piece of rope
Procedure -
1. Block the upper countershaft against the case wall.
2. With reverse gear forward against the next speed gear, lower
the mainshaft assembly while pulling the shaft rear through
the case bore.
3. Move the mainshaft pilot-end into the input shaft pilot bush-
ing. Mesh the mainshaft gears with the corresponding for-
ward countershaft assembly gears.
4. Center the mainshaft rear in case bore and temporarily posi-
Front Section
tion the auxiliary drive gear on the mainshaft. Partially seat
the bearing in the bore.
WARNING: At this time other components of the front sec-

tion must be Installed before the mainshaft installation can
be completed, see “How to Install the Countershaft Bear-
ings”.
5. Mesh the reverse gear teeth with the reverse idler gear teeth
and move the reverse gear to the rear as far as possible.
6. Remove the auxiliary drive gear.
7. Align the reverse gear spacer external splines with the re-
verse gear and move the spacer into the reverse gear.
8. Install the reverse gear I.D. snap ring and move the reverse
gear forward on the mainshaft and against the reverse gear
limit washer.
9. Install the reverse gear retaining snap ring in the mainshaft

second snap ring groove.
108
How to Install the Auxiliary Drive Gear Assembly
Before installing the auxiliary drive gear, the mainshaft must be completely installed.
Special Tools
• Large pair of snap ring pliers
• Flanged-end driver and maul
Procedure -
1. Install the splined washer on the mainshaft, against the re-

verse gear retaining snap ring.
2. Position the auxiliary drive gear assembly on the mainshaft.
3. Use a flanged-end driver and maul to seat the auxiliary drive

gear bearing.
4. Align the retainer ring capscrew holes with the tapped holes.

taining capscrews.

torque.
7. Install the splined washer inside the auxiliary drive gear as-
sembly.
8. Install the auxiliary drive gear retaining snap ring in the

mainshaft snap ring groove.
109
Auxiliary Drive Gear Assembly
How to Disassemble the Auxiliary Drive Gear Assembly
To disassemble, the auxiliary drive gear must be removed.
Special Tools
• A large pair of snap ring pliers
Procedure -
1. Lay the front auxiliary drive gear on a clean, flat surface.
2. From the front auxiliary drive gear hub, use a screwdriver to

pry off the snap ring retainer.
3. From the front auxiliary drive gear hub, remove the snap
ring.
Front Section
4. Use the front hub as a base and press the retaining ring and
bearing off.
110
5. From the front auxiliary drive gear hub, inspect the O-rings,
remove if damaged.
111
How to Assemble the Auxiliary Drive Gear Assembly
Inspect the O-rings and replace if damaged.
Apply Eaton Lubricant #71214 or equivalent to the auxiliary drive gear O-rings.
Special Tools
• A flanged-end driver and a maul
Procedure -
1. Lay the front auxiliary drive gear on a clean, flat surface.
2. Install the O-rings on the front auxiliary drive gear hub.
3. With snap ring groove away from gear teeth, install the re-
Front Section
taining ring on the front auxiliary drive gear.
4. With bearing snap ring facing groove in bearing ring, install

the bearing.
112
5. To retain the bearing, install the snap ring in front gear hub
groove.
6. With grooved side down, use a flanged-end driver and install

the outer retainer ring.
Final Check
• Make sure the outer retainer ring is seated.
113
Countershaft Assembly
How to Disassemble the Countershaft Assembly
Never use the PTO gear as a pressing base. The narrow width of this gear can cause breakage.
Special Tools
• Snap Ring pliers
• Press
Procedure -
1. From each countershaft front remove the drive gear retain-

ing snap ring.
2. Using the rear face of 3rd speed gear as a base, press the
drive gear, PTO gear, and 3rd speed gear from each counter-
shaft. This removes the front bearing inner race.
Front Section
3. Inspect the key and roll pin, remove if damaged.
114
How to Assemble the Countershaft Assembly
Except for the PTO gears, the upper and lower countershaft assemblies are the same. To avoid confusion during installation, mark
the upper countershaft (45-tooth PTO gear) with an “U”. The lower countershaft has a 47-tooth PTO gear.
Special Tools
• Snap ring pliers
• Press
Procedure -
1. If previously removed, install the roll pin and key in counter-

shaft keyway.
2. Align 3rd speed gear keyway with the countershaft key and
press the gear on the countershaft.
3. Align PTO gear keyway with the countershaft key and press
the gear on the countershaft.
4. Align drive gear keyway with the countershaft key and press
the gear on the countershaft.
115
5. On each countershaft front, install the drive gear retaining

snap ring in groove.
6. Use a flanged-driver or the press to install the bearing inner

race on the countershaft front against the drive gear.
Final Check
• Make sure all gears are pressed into place.
• Make sure the bearing inner race is installed.
Front Section
116
Mainshaft Assembly
How to Disassemble the Mainshaft Assembly
During disassembly, lay all parts on a clean bench in order of removal to facilitate reassembly.
When removing limit washers, spacers and gears, note their location. Keep the internal-splined washers and external-splined
spacers with the gear from which they were removed. There is only one limit washer and one spacer belonging to each gear.
Special Tools
Procedure -
1. Remove reverse gear.
2. Remove reverse gear spIine spacer.
3. Tilt the mainshaft up, and from the opposite end, remove the
sliding clutch.
4. Place the mainshaft in a vertical position.
5. Remove the mainshaft key snap ring.
6. From the mainshaft rear, pull the mainshaft key from the
mainshaft key way.
7. Turn the reverse gear limit washer to align its splines with
the mainshaft and remove the washer.
8. Remove the reverse-1st speed sliding clutch.
117
Mainshaft Assembly
9. Remove 1st gear and spline spacer.
10. Remove 1st gear spacer.
11. Turn the 1st gear limit washer to align its splines with the
mainshaft and remove the washer.
12. Turn the 3rd gear limit washer to align its splines with the
13. Remove the 3rd gear spacer.
14. Remove 3rd gear.
15. Remove 3rd gear spline spacer.
16. Turn the 3rd gear limit washer to align Its splines with the
17. Inspect the roll pin, remove if damaged.
Front Section
118
Mainshaft Assembly
How to Assemble the Mainshaft Assembly
Each mainshaft gear must have its I.D. snap ring installed before placement on the mainshaft. Do not replace reverse gear I.D.
snap ring.
Gear limit washers are internally splined and locked to the mainshaft by the key. Gear spacers are externally splined to engage with
gear hub clutching teeth. There is one limit washer and one spacer for each mainshaft gear.
Axial clearance (end-play) limits are .006"-.015" for all mainshaft gears.
If the axial clearance is less than the minimum .006" tolerance, the limit washer should be replaced with a thinner limit washer.
This will increase the axial clearance between the gears. If the axial clearance is greater than the maximum .015" tolerance, a thicker
limit washer should be installed. This will decrease the axial clearance between the gears.
Special Tools
• Feeler gauges
• A piece of 5/32" air line, 1' long
Procedure -
1. With mainshaft pilot-end down, secure the mainshaft in a

vise equipped with brass jaws or wood blocks.
2. If previously removed, install the roll pin in keyway.
3. With the washer flat side up, position the 3rd speed gear lim-
it washer (white) in the mainshaft 1st or bottom groove. Ro-
tate the washer until the washer splines and mainshaft
spIines align.
4. Start at the mainshaft bottom and install the air line in the
keyway to lock the washer in place. As limit washers and
gears are installed, continue to push the air line up.
119
Mainshaft Assembly
5. Against the 3rd speed gear washer, position the 3rd speed
gear spacer.
6. With clutching teeth down and engaged with the spacer ex-
ternal splines, position the 3rd speed gear on the mainshaft.
7. Against 3rd speed gear, position a mainshaft spacer.
Front Section
8. With the washer flat side down, position the limit washer
against the spacer. Rotate the washer until the washer
splines and mainshaft splines align.
9. Push the air line up to lock the washer on the mainshaft.
120
Mainshaft Assembly
10. Between the gear hub and mainshaft spacer, insert .006"
feeler gauge and .015" feeler gauge. If out of tolerance,
change the limit against the mainshaft spacer. See “Special
Instructions” for further information.
11. With the flat side up, position the 1st speed gear limit wash-
er (white) in the next available groove. Rotate the washer un-
til the washer splines and mainshaft splines align.
13. Against the limit washer, position the mainshaft spacer.
14. With clutching teeth up, position the 1st speed gear on the
mainshaft against the spacer.
15. Position 1st speed gear spacer against 1st speed gear, en-
gaging the spacer external splines with gear clutching teeth.
16. With washer flat side down, position the limit washer against
the spacer. Rotate the washer until the washer splines and
mainshaft splines align.
121
Mainshaft Assembly
18. Between the gear hub and mainshaft spacer, insert .006"
feeler gauge and .015" feeler gauge. If out of tolerance,
change the limit against the mainshaft spacer. See ‘Special
Instructions’ for further information.
19. Align the sliding clutch missing internal spline with the
mainshaft key and install the 1st-Reverse speed sliding
clutch.
20. With the flat side up, position the Reverse speed gear limit
washer (white) in the next available groove. Rotate the
washer until the washer spIines and mainshaft splines align.
Front Section
22. Against the limit washer, position reverse speed gear spac-
er.
122
Mainshaft Assembly
23. Install reverse gear on the mainshaft. Engage the gear

clutching teeth with spacer splines and sliding clutch. Move
the reverse gear down against the 1st speed gear.
24. At this time remove the air line and insert the mainshaft key.
WARNING: Be careful not to move the gears while doing this

procedure, the limit washers are unlocked and can rotate
which would cause the gears to drop.
25. Install the mainshaft key snap ring.
26. Remove the mainshaft from the vise.
27. On the shaft front, align the sliding clutch missing internal
spline with the mainshaft key and install the 3rd-Drive gear
sliding clutch. Engage the sliding clutch external splines with
the 3rd speed gear clutching teeth.
Final Check
• Make sure reverse gear is against 1st speed gear.
• Make sure the mainshaft key is in the keyway.
• Make sure the 3rd speed sliding clutch is engaged into
3rd speed gear.
123
Auxiliary Section
How to Disassemble the Auxiliary Section

AUXILIARY
SECTION
FRONT SECTION DRIVE

GEAR & YOKE
COUNTERSHAFT
ASSEMBLIES
REAR AUXILIARY
DRIVE GEAR
RANGE
CYLINDER
ASSEMBLY
Auxiliary Section
DISASSEMBLE
SYNCHRONIZER
ASSEMBLY OUTPUT
SHAFT
ASSEMBLY
SPLITTER
CYLINDER
ASSEMBLY
124
How to Remove the Front Auxiliary Drive Gear

Special Tools
Procedure -
1. From the splitter cylinder shift yoke, remove the lockwire

and capscrew.
2. Pull the sliding clutch and shift yoke straight out to remove
them.
125
How to Remove the Countershaft Assemblies (w/Tapered Bearings)
For "A" Series, go to “A” Series Section.
For ease of disassembly, mount the auxiliary section upright in a vise.
Both countershafts are removed the same.
Make sure the countershaft retaining straps are installed.
As the countershaft strap is removed, support the countershaft; it can fall.
Special Tools
• Vise with brass jaws or wood blocks
• Bearing puller
Procedure -
1. On the output shaft, temporarily install a output yoke.
2. To keep the output shaft from turning, insert a breaker bar.
Auxiliary Section
3. From the output shaft, loosen the 15/16" capscrew and re-
tainer. Do not remove the capscrew. Remove the bar and
output yoke.
126
4. Use a sort bar and maul to drive the output shaft forward far
enough to partially unseat the bearing.
5. Support the auxiliary countershaft while removing the auxil-

iary countershaft retaining strap.
6. Remove the auxiliary countershafts.
7. If necessary, secure the countershaft assemblies in a vise

and remove both the front and rear bearings with a bearing
separator and jaw pullers.
127
Countershaft Assembly (A Series Only)
How to Remove the Countershaft Assemblies (w/Ball Bearings) A Series
For ease of disassembly, mount the auxiliary section upright in a vise.
Both countershafts are removed the same.
When driving that countershaft to the rear, be careful not to damage the bearing inner race.
As the rear bearing is removed, the countershaft will fall.
Special Tools
• Bearing puller
Procedure -
1. From the countershaft rear bearing cover, remove the cap-

screws, cover, and gasket.
Auxiliary Section
2. Clean the gasket mounting surface of gasket material.
3. From the countershaft rear, remove the snap ring.
128
4. Use a sort bar and maul to drive the countershaft forward far
enough to partially unseat the bearing.
5. Use a soft bar and maul to drive the countershaft to the rear.
This exposes the bearing snap ring.
6. Use a bearing puller and remove the countershaft bearing

and countershaft.
7. Inspect the countershaft bearing inner race, remove if nec-

essary.
129
How to Remove the Rear Auxiliary Drive Gear
None
Special Tools
Procedure -
1. Retainer rectangular in shape.
From the output shaft, remove the 15/16" capscrew and re-
tainer.
Retainer round in shape.
From the output shaft, remove the 15/16" capscrew and re-
tainer, and thrust washer.
2. From the output shaft, remove the auxiliary drive gear. If the
retainer, from Step 1, is round, there will also be a thrust
washer behind the auxiliary drive gear to remove.
Auxiliary Section
130
How to Disassemble the Range Cylinder Assembly
When removing the range cylinder cover insert valves, note the direction the insert valve was positioned (nipple in or out).
Special Tools
Procedure -
1. From the range cylinder cover, remove the capscrews, cov-

er, and gasket.
2. Clean the gasket mounting surfaces of all gasket material.
3. From the range cylinder housing bore, remove the nut.
4. From the auxiliary section front, remove the two (2) yoke bar
retaining capscrews.
131
5. From the cylinder housing bore, remove the yoke bar.
6. From the shaft, pull the synchronizer shift yoke and the syn-
chronizer assembly.
7. From the cylinder housing bore, remove the range piston.
Auxiliary Section
8. Inspect the range piston O-rings, remove if damaged.
132
9. From the range cylinder housing, remove the housing and

gasket.
10. Clean the gasket mounting surfaces of all gasket material.
11. Inspect the O-ring inside the range cylinder housing bore,
remove if damaged.
12. Place the range cylinder cover in a vise, remove one insert
valve retaining nut and insert valve.
13. Inspect the insert valve and the cover bore for damage. Re-
peat for other insert valve.
For 14610A Models, go to Steps 14 and 15.
14. Place the range cylinder housing in a vise, remove the roll
pin.
133
15. Remove the interlock pin. Inspect the pin, replace if dam-
aged.
Auxiliary Section
134
How to Disassemble the Output Shaft Assembly
When using the soft bar and maul on the output shaft, be careful not to damage the threads.
When removing the rear bearing cover, the rear bearing cone drops from the housing bore.
Special Tools
• Press
Procedure -
1. Use a soft bar and maul to drive the output shaft forward and
through the rear bearing assembly.
2. From the auxiliary housing rear, remove the rear bearing re-
taining capscrews, cover, and gasket.
4. Inspect the rear bearing cover oil seal for damage, remove if
damaged.
135
5. From the auxiliary housing rear, remove the bearing cup and
spacer.
6. From the auxiliary housing front, remove the remaining

bearing cup.
7. From the output shaft, remove the bearing inner spacer.
8. Use the output shaft assemble gear front face as a base,
Auxiliary Section
press the output shaft through the bearing and gear.
136
How to Disassemble the Splitter Cylinder Assembly
When removing the splitter cylinder cover insert valve, note the direction the insert valve was positioned (nipple in or out).
Special Tools
Procedure -
1. From the splitter cylinder cover, remove the capscrews, cov-

er, and gasket.
3. From the cylinder housing, remove the yoke bar.
4. From the auxiliary housing, remove the splitter cylinder

housing.
137
5. From the splitter cylinder cover, remove the insert valve re-
taining nut and insert valve.
6. Inspect the insert valve and the cover bore for damage.
7. Inspect the yoke bar O-ring; remove if necessary.
8. Inside the cylinder housing bore; inspect the small 0-ring,

remove if damaged.
Auxiliary Section
138
Auxiliary Section
How to Assemble the Auxiliary Section

AUXILIARY
SECTION
ASSEMBLE
SYNCHRONIZER
ASSEMBLY
COUNTERSHAFT
ASSEMBLY
RANGE
CYLINDER
ASSEMBLY
REAR AUXILIARY
DRIVE GEAR
SPLITTER
CYLINDER
ASSEMBLY
FRONT AUXILIARY DRIVE

GEAR AND YOKE
AUXILIARY
SECTION
139
How to Assemble the Output Shaft Assembly
Make sure the magnetic plugs are installed in the auxiliary housing.
Output shaft stack up should be done on a clean, flat surface.
When heating the bearings, do not heat bearings above 275°F (136°C).
When installing the rear bearing race, the proper depth is when the race shoulder is seated on bearing bore top.
Because the collar becomes distorted when compressed, do not use an old nylon collar in the rear bearing cover.
Special Tools
• Heat lamp or hot plate and oil
• Oil seal installation tool
Procedure -
1. Use toolmaker’s dye and mark the LO range gear for timing
purposes.
Mark any two (2) adjacent teeth on the LO range gear. Re-
peat the procedure for the two (2) adjacent teeth directly op-
posite the first set marked.
Auxiliary Section
2. With splined washer facing up, place the washer on the out-
put shaft shoulder.
140
3. With LO range gear clutching teeth down, position LO range

gear on the output shaft, engage the washer splines.
4. With chamfer side up, position the LO range gear rear wash-
er on the output shaft against the LO range gear.
5. With tapered side up, use heat or appropriate driver and in-
stall the output shaft front rear bearing.
6. On the output shaft, position the bearing inner spacer. Set

aside.
141
7. Lay the auxiliary housing front face up on a clean, flat sur-

face. Install the front bearing cup.
8. Turn the auxiliary housing over, install the rear bearing spac-
er and rear bearing race in the bearing bore.
Auxiliary Section
142
Output Shaft Assembly (A Series Only)
How to Assemble the Output Shaft Assembly (A Series)
Make sure the magnetic plugs are installed in the auxiliary housing.
Output shaft stack up should be done on a clean, flat surface.
When heating the bearings, do not heat bearings above 275°F (136°C).
When installing the rear bearing race, the proper depth is when the race shoulder is seated on bearing bore top.
Because the collar becomes distorted when compressed, do not use old nylon collar on rear bearing cover.
Special Tools
• Heat lamp or hot plate and oil
• Oil seal installation tool
Procedure -
1. Use toolmaker’s dye and mark the LO range gear for timing
purposes.
Mark any two (2) adjacent teeth on the LO range gear. Re-
peat the procedure for the two (2) adjacent teeth directly op-
posite the first set marked.
2. With splined washer facing up, place the washer on the out-
put shaft shoulder.
143
3. With LO range gear clutching teeth down, position LO range

gear on the output shaft, engage the washer splines.
4. With chamfer side up, position the LO range gear rear wash-
er on the output shaft against the LO range gear.
5. With tapered side up, use heat or appropriate driver and in-
stall the output shaft front rear bearing.
Auxiliary Section
6. On the output shaft, position the bearing inner spacer. Set
aside.
144
7. Lay the auxiliary housing front face up on a clean, flat sur-

face. Install the front bearing cup.
8. Turn the auxiliary housing over, install the rear bearing spac-
er and rear bearing race in the bearing bore.
9. With the auxiliary housing rear up, set the housing over the
output shaft.
10. With tapered side down, use heat or appropriate driver and
install the output shaft rear bearing.
11. Position a new gasket on the rear bearing cover mounting

surface, making sure the gasket oil return holes align with
the case oil return holes.
12. If previously removed, use an oil seal installation tool and in-
stall the oil seal in the rear bearing cover.
145
13. Position the rear bearing cover over the new gasket.

taining capscrews.
15. Install the five (5) retaining capscrews in the non-chamfered

hole, tighten to 35-45 lb-ft of torque.
16. Install the nylon collar and brass washer in the chamfered
Final Check
• Make sure the rear bearing is seated.
• Make sure the rear bearing capscrews are properly
torqued.
• Make sure the output shaft rotates freely.
Auxiliary Section
146
How to Install the Countershaft Assemblies (w/Tapered Bearings)
To make auxiliary section assembly easier, you can make an auxiliary section fixture out of a 2" x 12".
Make sure to use an auxiliary drive gear retaining bolt with thread sealant material.
Special Tools
• Auxiliary countershaft retaining straps
Procedure -
1. Place the countershaft assembly vertical on a clean, flat sur-

face. If previously removed, use the proper driver and maul
to install the countershaft bearings.
2. Mark each countershaft for correct timing. Locate the "O"

stamped on the countershaft and mark the tooth with highly
visible toolmaker's dye or paint.
3. Install the synchronizer assembly on output shaft front.
4. Place the thrust washer, the rear auxiliary drive gear, the
thrust washer, the retainer and the 15/16" capscrew on the
output shaft assembly. Finger tighten the capscrew.
147
5. Place the countershafts in the fixture or on a flat surface for

reassembly. Turn the countershafts so that the two teeth
marked on each LO range gear are towards the middle.
6. Align the output shaft between the countershafts, match the

timing marks.
7. With range yoke offset side facing down, install into the syn-
chronizer sliding slot.
8. Place the auxiliary housing over the countershaft assemblies

and the output shaft assemble.
Auxiliary Section
9. Heat the rear output bearing cone and install the bearing, ta-
pered side down, on the shaft.
10. Position a new gasket on the rear bearing cover mounting

surface.
148
11. Position the rear bearing cover.

taining capscrews.
13. Install the five (5) retaining capscrews in the non-chamfered

14. Install the nylon collar and brass washer in the chamfered
15. Install each auxiliary countershaft retaining strap with 2 - 3/

8" NC x 1" and 1 - 3/8" NC x 2 -1/2" clean capscrews.

capscrews are snug.
149
How to Install the Countershaft Assemblies (w/Ball Bearings) A Series
For ease of assembly, mount the auxiliary section in a vise.
When Installing the countershaft assemblies into the countershaft bearings, keep the countershaft assemblies straight. Do not
cock the countershafts.
If, when the countershaft bearing cover is removed and you can not see the snap ring groove, install the cover and drive the coun-
tershaft further until you can see the groove.
Special Tools
• Bearing driver and a maul
• Large snap ring pliers
Procedure -
1. Place the countershaft assembly vertical on a clean, flat sur-

face. If previously removed, using the proper driver and
maul install the countershaft bearing race.
Auxiliary Section
2. In the countershaft rear bearing bore, using the proper driv-
er and maul, install the countershaft bearing.
150
3. Temporarily install the rear bearing cover, use two (2) cap-
screws and no gasket. The cover holds the bearing as the
countershaft is driven into the bearing.
4. Use toolmaker’s dye and mark the smaller LO range gear

tooth that aligns with countershaft gear marked with an “O”.
5. Position the countershaft in the auxiliary housing. Mesh the

countershaft marked tooth with either set of LO range gear
marked teeth.
6. Use a sort bar and maul and drive the countershaft into the
countershaft bearing.
151
7. From the auxiliary housing rear, remove the countershaft

bearing cover and install the rear countershaft snap ring in
the snap ring groove.
8. Position a new gasket on the countershaft bearing cover

mounting surface.
9. Position the countershaft bearing cover over the gasket.

taining capscrews.
11. Install the capscrews, tighten to 35-45 lb-ft of torque.
12. Repeat all steps for other countershaft installation.
Final Check
• Check both countershafts for timing; the output shaft
should rotate freely.
• Check capscrews for proper torque.
Auxiliary Section
152
How to Assemble the Range Cylinder Assembly
Apply Eaton lubricant #71214 or equivalent to all shift cylinder assembly and insert valve O-rings so a film covers the entire surface
of each O-ring.
Apply Eaton rust preventative #71213 or equivalent to all shift cylinder walls and yoke bars, cover the entire yoke bar surface that
comes in contact with the shift cylinder O-ring.
Apply Eaton lockwire #1619 or equivalent to the shift yoke capscrews. The lockwire should anchor each capscrew head securely
to the yoke or to the second capscrew which fastens to the yoke bar. The lockwire should be twisted together, trimmed, and bent
out of the way of other parts.
Special Tools
Procedure -
1. If previously removed, install the interlock pin in the cylinder

housing. ("A" Series Only).
2. If previously removed, install the roll pin. ("A" Series Only).
153
3. If previously removed, in the cylinder housing bore, install

the small O-ring.
4. If previously removed, on the piston I.D. and O.D., install the

piston O-rings.
5. Position a new gasket on the cylinder housing mounting sur-

face.
6. From the rear, with the air passage away from the rear bear-
ing cover, install the cylinder housing.
7. Place the range shift yoke, with the threaded yoke hub up
Auxiliary Section
and HI range synchronizer towards the front, in the sliding
clutch slot.
8. Place the range shift yoke and synchronizer assembly on the

output shaft, engaging the sliding clutch splines.
154
9. With the yoke bar threaded-end, insert the yoke bar into the
range cylinder housing bore, through the range shift yoke
hub. Align the bar notches with range shift yoke lockscrew
holes.
10. Install the two (2) yoke bar retaining capscrews, tighten to
50-65 lb-ft of torque.
11. From the rear, insert the piston. Push it in as far as it will go.
12. Secure the piston with the retaining nut, tighten to 70-85 lb-
ft of torque.
155
13. If previously removed, install, in one of the cylinder cover

bores, the insert valve, nipple in the proper direction.
14. If previously removed, install, over the insert valve, the in-
sert valve retaining nut. Tighten the retaining nut to 40-50 lb-
ft of torque. Repeat for other insert valve.
15. Position a new gasket on the cylinder housing cover mount-

ing surface. The gasket air passage must align with the
housing air passage.
16. Over the gasket, position the range cylinder cover.

taining capscrews.
18. Install the capscrews, tighten to 20-25 lb-ft of torque.
Final Check
• Make sure all capscrews are tighten to their proper
torque.
• Make sure gaskets were used at the appropriate posi-
Auxiliary Section
tions.
156
How to Install the Rear Auxiliary Drive Gear
None
Special Tools
• Output yoke and breaker bar
Procedure -
1. Temporarily install the output yoke.
2. To keep the output shaft from turning, insert and hold the
breaker bar.
3. Tighten the auxiliary drive gear retainer bolt to 90-120 lb-ft

of torque. Remove the breaker bar and output yoke.
Final Check
• Make sure the auxiliary drive gear retainer bolt is prop-
erly torqued.
157
How to Assemble the Splitter Cylinder Assembly
Apply Eaton lubricant #71214 or equivalent to all shift cylinder assembly and insert valve O-rings so a film covers the entire surface
of each O-ring.
Apply Eaton rust preventative #71213 or equivalent to all shift cylinder walls and yoke bars, cover the entire yoke bar surface that
comes in contact with the shift cylinder O-ring.
Apply Eaton lockwire #1619 or equivalent to the shift yoke capscrews. The lockwire should anchor each capscrew head securely
to the yoke or to the second capscrew which fastens to the yoke bar. The lockwire should be twisted together, trimmed, and bend
out of the way of other parts.
Special Tools
Procedure -
1. If previously removed, in the cylinder housing bore, install

the small O-ring.
2. If previously removed, on the piston O.D., install the piston
Auxiliary Section
O-ring.
158
3. Place the auxiliary housing upright in a vise.
4. Position a new gasket on the cylinder housing mounting sur-

face.
5. From the rear, with the air passage towards the rear bearing
cover, install the cylinder housing.
6. From the rear, insert the piston. Make it flush with the cylin-
der housing.
7. If previously removed, install in the cylinder cover bore the

insert valve, nipple in the proper direction.
8. If previously removed, install over the insert valve the insert

valve retaining nut. Tighten the retaining nut to 40-50 lb-ft of
torque.
9. Position a new gasket on the cylinder housing cover mount-

ing surface. The gasket air passage must align with the
housing air passage.
159
10. Position the splitter cylinder cover over the gasket.

taining capscrews.
12. Install and tighten the retaining capscrews to 20-25 lb-ft of

torque.
Final Check
• Make sure the retaining nut and capscrews are tighten
to proper torque.
• Make sure gaskets were used at appropriate positions.
Auxiliary Section
160
How to Install the Front Auxiliary Drive Gear
Make sure the splitter yoke bar lockscrew hole aligns with the yoke lockscrew hole.
Special Tools
Procedure -
1. Place the shift yoke in splitter sliding clutch slot. Install the
clutch and yoke on the splitter yoke bar.
2. Install the lockscrew and tighten to 35-45 lb-ft of torque.

Lockwire securely.
161
How to Disassemble the Synchronizer Assembly
Place the synchronizer assembly on a clean, flat surface. Cover the synchronizer assembly with a shop rag to prevent losing the
three (3) springs under pressure from the HI range synchronizer pin locations.
Special Tools
• Shop rag
Procedure -
1. Place the larger LO range synchronizer ring on the bench.
2. Grab both sides of the HI range synchronizer and pull.
3. From the synchronizer ring LO range pins, remove the slid-

ing clutch.
Auxiliary Section
162
How to Assemble the Synchronizer Assembly
Assembly should be done on a clean, flat surface slightly lower than your waist.
Pins on the Low range synchronizer must line up with the chamfered holes on the sliding clutch bottom.
When compress the HI range synchronizer springs cover with a shop rag. In the event compression is not achieved the first time,
this prevents the springs from leaving the bench area.
Special Tools
• Shop rag
Procedure -
1. On the bench place the larger LO range synchronizer ring

face down with pins up.
2. With the sliding clutch recessed side up, place the sliding
clutch on the LO range synchronizer pins.
3. In the HI range synchronizer bores, install the three (3)

springs.
163
4. Place the HI range synchronizer ring over the LO range syn-

chronizer ring. Rotate the HI range synchronizer until the
springs are seated against the pins.
5. With the shop rag, cover the assembly.
6. Apply downward pressure to the HI range synchronizer ring

while twisting counterclockwise. This compresses the
springs to fully seat HI range on the LO range synchronizer.
Final Check
• Make sure there are three springs and are fully com-
pressed.
• Make sure you can move the sliding clutch from HI to
LO range and back.
Auxiliary Section
164
Integral Oil Pump
How to Remove the Integral Oil Pump
None
Special Tools
Procedure -
1. Straighten tube lock on suction tube.
2. Remove suction tube from oil pump. If necessary, remove

O-ring from suction tube.
3. Remove three (3) allen head capscrews and washers that re-
tain the integral oil pump to the case.
4. Remove the integral oil pump assembly from inside the

case.
165
Integral Oil Pump
5. Remove the integral oil pump retainer plate from inside the
case.
6. If necessary, the front case plug can be removed from the

case. To remove, insert a bar from inside the case and tap
the plug out.
7. Inspect the plug O-ring, replace if damaged.
Options
166
Integral Oil Pump
How to Install the Integral Oil Pump
Lubricate the case front plug O-ring with Eaton/Fuller lubricant #71206 or equivalent.
Special Tools
Procedure -
1. If removed, replace the front case pump plug O-ring. lubri-

cate the grove of the plug, install the O-ring onto the plug,
and then lubricate the outer diameter of the O-ring.
2. Seat the front case pump plug in the case bore by hand. Do
not install the pump plug using any type of impact tool (i.e.
hammer, maul, etc.).
Note: P/N 4303107 retainer plate, which has a smaller out-

side diameter, must be used with maincase machined
after April 1995. If an older oil pump assembly is in-
stalled into a new case, P/N 20510 retainer plate will
not seat properly in the spot face machined in the case
wall
3. With the retainer bore facing the case rear, install the integral
oil pump over the alignment pin inside the case.
4. Align oil pump with retainer and alignment pin and install the
integral oil pump assembly.
167
Integral Oil Pump
5. Install three (3) allen head capscrews and washers through

the case front and into the pump housing. Tighten the cap-
screws to 8-12 lb-ft of torque.
6. Replace the O-ring on the suction tube.
7. Install the tube under the case rib and into the integral oil
pump.
8. Bend the suction tube lock over the case rib.
Final Check
• Make sure the integral oil pump drive gear can turn.
Options
168
Integral Oil Pump
How to Disassemble the Integral Oil Pump
None
Special Tools
Procedure -
1. From the assembly, remove the outer oil pump element.
2. From the drive shaft, remove the drive gear retaining snap
ring.
3. From the pump drive shaft, remove the drive gear.
4. From the drive shaft keyway, remove the key.
5. From the drive shaft, remove the element snap ring.
6. From the drive shaft, remove the internal oil pump element.
7. From the drive shaft keyways, remove the two (2) keys.
169
Integral Oil Pump
8. From the integral oil pump housing, remove the drive shaft.
9. If damaged, from the drive shaft, remove the rear drive gear
retention snap ring.
10. From the pump housing, remove the relief valve roll pin.
11. From the relief valve housing bore, remove the relief valve
spring.
12. From the housing bore, remove the relief valve.
13. Inspect all parts for damage, replace damaged parts.
Options
170
Integral Oil Pump
How to Assemble the Integral Oil Pump
When installing the drive shaft keys, the round key goes in the round keyway and the square key in the square keyway.
Special Tools
Procedure -
1. Install the relief valve in the integral oil pump housing.
2. Install the relief valve spring in oil pump housing.
3. Secure the oil pump housing in a vice.
4. Depress the relief valve spring and drive the relief valve re-
tention roll pin into the roll pin bore.
5. If removed, replace the drive shaft snap ring on the pump

drive shaft.
6. Insert the drive shaft through the pump housing bore.
7. Install the two (2) keys on the drive shaft.
8. Align the inner element keyways with the drive shaft keys
and install the integral oil pump inner element.
171
Integral Oil Pump
9. Install the inner element retention snap ring in drive shaft

snap ring groove.
10. Install drive gear key in drive shaft keyway.
11. Align drive gear keyway with drive shaft key and install the
drive gear on the drive shaft.
12. Install the outer drive gear retention snap ring in drive shaft
groove.
13. Install the outer integral oil pump element over the inner el-
ement.
Options
172
Copyright Eaton and Dana Corporation,
2002. EATON AND DANA CORPORATION
hereby grants its customers, vendors, or
distributors permission to freely copy,
reproduce and/or distribute this document
The Roadranger® System is an unbeatable combination of the best
in printed format. THIS INFORMATION IS
NOT INTENDED FOR SALE OR RE-
products from Eaton and Dana – partnering to provide you the most
SALE, AND THIS NOTICE MUST REMAIN advanced, most trouble-free drivetrain in the industry. And it’s backed by
ON ALL COPIES. the Roadrangers – the most experienced, most expert, most accessible
drivetrain consultants in the business.
For spec’ing or service assistance, call 1-800-826-HELP (4357) 24 hours
a day, 7 days a week, (Mexico: 001-800-826-HELP (4357)) for more time
on the road. Or visit our web site at www.roadranger.com.
TRSM-0550
10/02 PDF
Printed in USA

Caja de Super 10

Uploaded by

Copyright:

Available Formats

Caja de Super 10

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Caja de Super 10

Uploaded by

Copyright:

Available Formats

What are the main precautions to take before working on or driving a vehicle?

What are the main precautions to take before working on or driving a vehicle?

What are the main sections covered in the service manual?

What are the main sections covered in the service manual?

® ®

Eaton Fuller Heavy Duty Transmissions

Service Manual TRSM-0550 April 2006

Warnings and Precautions

Always use genuine Eaton replacement parts.

General Information How to Install the Input Shaft

General Service Practices and Part Inspection ............ 1

General Service Practices and Part Inspection

Recommended inspection procedures are provided in the following checklist.

Oil Return Threads and Seals

How to use this Manual

Follow the flow chart "How to Disassemble the Auxiliary Section".

Front Auxiliary Drive

Front Auxiliary Drive

WARNING: Do not remove or destroy the transmission identification tag.

B. Marking main drive gear teeth.

Helical Auxiliary Section

Additives and friction modifiers must not be introduced.

Buy from a reputable dealer

Transmission Operating Angles

Operating Temperatures with Oil Coolers

Oil Cooler Chart

Transmission Oil Coolers are:

Part to inspect What to Check For Action to be Done

Oil Leak Inspection Process

Determine if it is a Weep or a Leak

Gasket Rear Seal Leak

How to Disassemble the External Parts

AIR FILTER/ ROADRANGER OUTPUT YOKE/

How to Assemble the External Parts

OUTPUT YOKE/ CLUTCH CHANGING THE

AUXILIARY SHIFT BAR

AIR GEAR SHIFT

How to Remove the Air Lines and Hose

1. Disconnect all air lines and hose.

2. Inspect the air lines and hose.

3. Inspect air fittings, remove if damaged.

How to Install the Air Lines and Hose

Make sure air lines and hose are not damaged.

Install the air lines and hose at their proper location.

1. Replace removed air fittings.

2. Connect all removed air lines and hose.

How to Remove the Air Filter/Regulator

1. From the air filter/regulator, remove the two (2) capscrews.

3. Inspect the O-rings for cracks or distortion.

How to Install the Air Filter/Regulator

1. On the range cylinder cover, position the two (2) o-rings.

2. Over the o-rings, position the air filter/regulator.

3. Apply eaton/fuller sealant #71205 or equivalent to the two

4. Install the two (2) retaining capscrews, tighten to 8-12 lb-ft

How to Remove a Roadranger Valve

The air lines must be depressurized.

1. From the Roadranger valve cover, remove the two (2)

3. From the air fittings, disconnect the air lines.

6. On the Roadranger valve, inspect the air fittings; remove if

How to Install a Roadranger Valve