Basic Diode Laser

BN 1000
May 2000
Profile Optische Systeme GmbH

Gauss Str. 11
D - 85757 Karlsfeld / Germany
Tel + 49 8131 5956 - 0

Fax + 49 8131 5956 - 99
info@profile-optsys.com
www.profile-optsys.com
Profile Inc.
87 Hibernia Avenue
Rockaway, NJ 07866
Tel +1 973 664-9385

Fax +1 973 664-9384
Basics on laser diodes
Summary
Laser diodes are semiconductor devices emitting coherent light. They

are the most frequently used laser sources. Their small size, the rela-
tively low price and their long lifetime make them a component for
multiple applications.
Since their invention in 1963 the development of laser diodes has

been pushed considerably, mainly due to the strong growth in the
fields of telecommunication and optical data storage. These and other
fields of application have led to an important progress as to size and
reliability. Continuous developments have resulted in laser diodes with
shorter and shorter wavelengths, increasing output power and an im-
proved beam quality.
In the following we will describe how laser diodes operate and what
their special features are. This applies to the characteristic curves, the
spectrum, the characteristics of the beam and other important pa-
rameters.
We will describe typical types of laser diodes and their fields of appli-
cation.
Handling laser diodes requires utmost care to protect them against

damage and destruction. Therefore, we will also give some instruc-
tions concerning the correct handling of laser diodes.
Contents
1 Generating a coherent emission in the laser diode 3

2 Types of laser diodes 5
3 Substrates 7
4 Characteristics and features of laser diodes 8
4.1 Characteristic curves 8
4.2 Optical spectrum 9
4.3 Beam characteristics 10
4.4 Temperature behaviour 12
4.5 Modulation behaviour 17
4.6 Noise and backreflections 18
5 Precautions in handling a laser diode 19
6 Laser diode controllers 20
7 Laser diode packages 20
8 Literature 22
Copyright 2000, Profile GmbH
Summary 2
1 Generating a coherent emission in the laser diode
The laser diode (LD) and the related light emitting diode (LED) are LD/ LED
semiconductor devices with pn-junctions. Depending on the kind of
emission there is a difference between surface or edge emitting di-
odes.
Most LEDs are surface emitters (SLED: Surface-emitting LED). Due SLED - EELED
to a special layer set-up also edge-emitting LEDs (EELED) that have a
higher degree of effiency, can be realized. If you combine this struc-
ture with a fiber guide you will reach – due to the concentration of the
radiation in the fiber guide – still higher radiation densities. This is then
called super-luminescence diodes.
Common laser diodes are always edge emitters. Recently, however,

also surface emitting laser diodes have become of interest for special
applications (VCSEL: Vertical Cavity Surface Emitting Laser) (see
chapter 2).
While LEDs can only emit incoherent light, laser diodes emit coherent
light when operated above the threshold.
This is due to the stimulated emission. The emitted stimulated pho-

ton is conform with the photon that has released the emission regar-
ding energy (wavelength resp. frequency), phase and direction propa-
gation. Fig. 1 shows the differences between coherent and incoherent
emission.
Figure 1: Incoherent and coherent emission
To cause an amplification of the light by stimulated emission, the

probability of an emission must be above that of an absorption for the
spectral range concerned. This is achieved by „pumping“ the laser:
the semiconductor is shifted into a state of inversion. Then, in the
upper energy level the density in numbers of electrons is higher than
in the lower one.

This so-called density inversion can be reached through an extreme

doting of the n- or p-material by injecting minority carriers.
The emission becomes coherent due to a selective feedback gene-

rated by an optical resonator that can be realised in form of two resonator principle
mirrors facing each other (Fabry-Perot resonator, see fig. 2).
By multiple reflection, standing waves can build up for certain dis-

crete wavelengths. The semiconductor in inversion operates as ampli-
fier. The split end faces of the crystal serve as mirrors since due to
the change of the refractive index against air, about 30 % of the emis-
sion is reflected.
Figure 2: Fabry-Perot resonator
Figure 3: Amplification and resonant frequencies in the optical resonator

Laser operation is possible at those resonator frequencies (longitudi-

nal modes) for which the optical amplification exceeds the losses due
to coupling and absorption (compare fig. 3). laser operation
The modes are competing with each other and are fluctuating in time
(modal noise). By certain means it can be achieved that only one lon-
gitudinal mode is amplified. The laser then emits as singlemode
source.
2 Types of laser diodes
Traditional laser diodes provide a horizontal resonator structure where

the double hetero structure serves to guide the light vertically in the
active zone (fig. 4).
Figure 4: Principle structure of a laser diode guided in the active laser region
According to the different refractive indices of the different layers the gain guiding
light is guided in the active zone. The lateral limitation of the light is index guiding
achieved by either index guiding or by gain guiding.
Index guided lasers provide an additional built-in refractive index pro-

file perpendicular to the direction of light propagation. With gain
guided lasers the guiding in the narrow stripe is achieved by lateral
tightening and concentration of the stimulating electrical field.
Gain guided lasers are easier to produce, are offered at a lower price
and have a higher reliability. Index guided lasers provide a better
beam quality and require a lower threshold current.
Due to its better characteristics the index guided laser has clearly
overtaken the gain guided laser on the market for telecommunication.
This applies especially to the DFB laser (Distributed-Feedback-Laser). DFB
With this kind of laser the reflections are not effected by the plane mir-
rors of the crystal but by a corrugation of the semiconductor substrate.
These undulated elevations have the effect of a mirror with a high re-
flection power (fig. 5).

Figure 5: Schematic structure of a DFB laser
DFB lasers are very selective. Contrary to the Fabry-Perot resonator

this principle is called Bragg reflector. Only one mode of the spec-
trum fulfils the resonance condition and is amplified.
Thus it is possible to realise very narrow-band lasers that result in

small signal distortion by chromatic dispersion of a fiber, using the la-
ser as a carrier for data. In connection with singlemode fibers DFB la-
sers are therefore especially suited to realise large bandwidths and
long transmission distances.
Another important type of laser is the vertical cavity surface emitting VCSEL
laser diode (VCSEL). This type disposes of a resonator that is in a
right angle to the active layer. The laser emits at the surface (fig. 6).
Figure 6: Vertical cavity surface emitting laser (VCSEL)
The resonator consists of multi-layer mirrors above and below the ac-
tive zone. These mirrors must have a considerably higher reflection
than those of horizontal emitting laser diodes as in the VCSELs the
photons only pass a relatively short distance in the active zone.
VCSELs typically emit with relatively large symmetric apertures. Thus

the beam is round and shows little divergence.
Due to their structure surface emitting laser diodes have only one
beam window, compared to common diodes. This is a disadvantage
as for many applications a second beam is necessary for controlling
purposes, e.g. to stabilise the output power.

Many other types of lasers with increasingly complicated structures

have been developed to improve certain parameters.
Another method is the set-up of laser bars (= arrays). Here several

single lasers are arranged next to each other. If several laser bars are
stacked onto each other, we are talking about laser stacks. With laser laser bar
bars and laser stacks very high optical powers can be achieved. This laser stack
is the reason why these devices are highly interesting for applications
in material treatment (rapid prototyping...).
Further applications for these components are, for example, point-to-

point communication in space, laser printing, laser beam writing, but
also the optical pumping of solid state lasers like Nd-YAG.
However, the higher optical power can only be used if it is coupled into
a medium with sufficiently large dimensions (diameter and numeric
aperture).
When coupled into a singlemode fiber with a very small numerical

aperture, even with additional collimating lenses it is not possible to
get more power into the fiber than with only one single laser. This is
due to general physical laws that do not allow an increase in beam
density.
3 Substrates
The semiconductor substrates which the laser diodes consist of are di-
rectly responsible for the wavelength the laser diodes emit.
With a pn-junction GaAlAs can emit from 750nm to 880nm and thus
fully covers the range of the first optical window.
The lasing wavelength is a function of the band gap and is determined

by material, the concentration of dopants and the configuration of the
active zone.
InGaAsP is mainly used to manufacture components in the 1300nm

and 1550nm range (second and third optical window).
InGaAlP is used for semiconductor lasers in the visible range starting

at 630nm. These lasers are suited for data transmission with synthetic
plastic fibers. In many applications they substitute the HeNe laser, for
example for barcode scanners.
Up to now even lower wavelengths can only be realised with semicon-

ductor lasers via frequency doubling. For higher wavelengths (2,0µm
to 2,3µm) GaInAsSb is used.
Profile supplies convenient temperature controllers also for lead sul-

fate lasers that emit at an working temperature of 25K to 70K (Kel-
vin) at a wavelength of 3 to 25 µm.
3 Substrates 7
4 Characteristics and features of laser diodes
4.1 Characteristic curves
Above a characteristic threshold current IS, at which the laser diode

starts lasing, the ideal laser diode shows a linear dependence between
optical output power and laser current. Below this threshold the optical
amplification is not sufficient: The light is emitted spontaneous, like a
LED does. Fig. 7 shows that the characteristic curve of a laser diode
does not differ from that of an LED at operating currents below the
threshold.
Figure 7: Characteristic curves of a LED and a laser diode
Important parameters of the characteristic curve are their slope, the important parameters
threshold current, the roundness at the threshold and the linearity of
laser operation.
The linearity is characterised by a ratio of harmonics. Especially high

demands to linearity are put for frequency modulated resp. analog
signals.
If the optical output power is too high, the laser mirrors will be de- Attention!
stroyed. Therefore it is essential to limit the maximum output power.
Typical powers for fiber coupled components are at only a few milli-
watts. You cannot couple the total power into the fiber. With single-
mode fibers typical coupling efficiency is approximately 50 %.
With open beam laser diodes output powers up to some kilowatts can
be reached.
The slope of the characteristic curve, measured in mW/mA, is directly

determined by the efficiency of the device in laser operation. The
slope of a laser diode with pigtail is reduced by a factor that is de-
pendent on the coupling efficiency of the laser power into the fiber.

4.2 Optical spectrum
The optical spectrum of a laser with Fabry-Perot resonator has already

been discussed in the first paragraph. It consists of single spectral
lines with a spacing of ∆λ. The spectral width of each spectral line is
influenced by many factors, especially by the laser power.
Figure 8: Spectrums of laser diodes:

(a) gain guided laser, (b) index guided Fabry-Perot laser, c) DFB laser
Fig. 8 shows the spectrums of gain guided and index guided semicon-
ductor lasers. With gain guided lasers a multimode structure can be
recognised. This is due to the higher spontaneous emission compared
to that of the index guided laser. The envelope curve corresponds to
the amplification profile above the laser threshold. The 3-db width is
some nanometers.
With the index guided Fabry-Perot laser one spectral line is dominant,
in most cases, but side modes can clearly be recognised. With the
DFB laser, index guided too, the linewidth is considerably smaller and
the side modes are much more suppressed than with the Fabry-Perot
laser.
The coherence length lcoh of laser diodes is low. It can be calculated

from the spectral width δλ of each emitted spectral line respectively
from the 3-db width of the spectrum:
λ2 λ2
l coh = resp. l coh = (1)
δλ 3 − dB width
Thus an index guided Fabry-Perot laser, emitting a single spectral line

-2
of 10 nm at 825 nm, has a coherence length of 7 cm. For a gain
guided Fabry-Perot laser with a 3-db bandwidth of 2,2 nm the coher-
ence length is 300µm only. Thus, for a DFB laser with a typical line
-4
width of 10 nm the coherence length is 7 m correspondingly.

There is the following relation between the phase velocity v, the

wavelength and the frequency f, which is determined during the gen-
eration of the radiation:
v
f= (2)
λ
By differentiating from f(λ) to λ you get a relation between the line

width δλ respectively the δλ3dB (width) and the corresponding fre-
quency range ∆f:
v v
∆f = δλ resp. ∆f = 2 δλ3dB (3)
λ 2
λ
Typical multimode lasers with a 3-db width of 2 nm to 3 nm corres- frequencies

pond to a frequency range of about 1000 GHz. The frequency range
of an index guided Fabry-Perot laser is at some GHz. Extremely nar-
row-band lasers provide a line width in the sub-MHz range. They dis-
pose of correspondingly high coherence lengths.
4.3 Beam characteristics
The beam of a laser diode is divergent with a rather large radiation divergence
angle. This is due to the diffraction of the light waves when coupled
out of the laser diode. Inside the laser the light waves are limited to the
active zone (see chapter 2).
As the active, light emitting area is shaped rectangular with strongly

differing edge lengths, the parallel and vertical divergence are diffe-
rent.
Therefore, in some distance from the emitting area the beam will ap-
pear as an elliptical spot (fig. 9), so that the coupling into fiber with a
low numeric aperture and a small core diameter becomes difficult.
Figure 9: Typical beam characteristic of a semiconductor laser

Gain guided and index guided laser diodes have a different distribution
of intensity inside the spots. The “ears” of the gain guided laser in the
parallel plane θll are characteristic.
Fig. 10 compares the near field, the far field (corresponds to the inten-
sity distribution as a function of the angle in a certain distance of the
emitting area) and the spectrum of a gain guided and an index guided
laser. FWHM (full with at half maximum) here is the 3-dB width of the
near field intensity.
Figure 10: (a) near field (parallel plane), (b) far field (vertical plane), (c) far field (parallel plane)
and (d) spectrum of a gain guided (upper) and an index guided (lower) laser diode
The ratio of vertical to parallel divergence, measured in the far field, is

called the ratio of axes.
The focus of the vertical and the focus of the parallel divergence are
not congruent but shifted against each other (fig. 11). This effect is
called astigmatism. Typical values for astigmatism are for the gain
guided lasers 30µm and for the index guided lasers 10µm.

Figure 11: Astigmatism of a laser diode
Vertical cavity surface emitting lasers (VCSEL) have square or round

emitting areas and therefore dispose of a relatively symmetrical
beam. The emitting area is larger than that of a common laser and
therefore has a lower divergence (7 to 10 degrees).
Laser diodes are emitting almost linear polarised light if they are
driven above the threshold. The reason for this is the polarisation de-
pendency of the reflection factor R of the emission area of the crystal.
This effect is only provided with rectangular emission areas. In this,

the polarisation vector points in the direction of the longer edge of the
rectangle.
The ratio between the parallel and vertical polarisation vectors of the
beam is called polarisation ratio. At a lower operating current the
share of unpolarised light is higher due to the spontaneous emission.
With increasing output power the polarisation ratio increases. Laser

diodes that are driven near their maximum power show polarisation
ratios of more than 100:1.
4.4 Temperature behaviour
The characteristics of a laser diode strongly depend on the tempera-

ture. Fig. 12 shows the characteristic curve of a diode at different
temperatures. With increasing temperature the threshold current in-
creases and the slope of the curve decreases.
Figure 12: Temperature dependency of the characteristic curve

For the shift of the threshold current the following dependency was
determined empirically:
∆T
IS ( T + ∆T) = IS ( T) e T0
(4)
T0 is a substrate specific characteristic temperature and ∆T is the de-

viation from temperature T. The smaller T0, the more sensitive the la-
ser reacts to changes in temperature. For GaAlAs laser diodes T0
ranges from120K to 230K and for InGaAsP lasers from 60K to 80K.
The shift of the threshold current is due to the temperature depen-

dency of the carrier concentration in the active layer and also – with
increasing temperatures - to an increasing probability for non-emitting
recombination processes.
In pulsed operation the chip temperature of a laser diode is lower de-

pending on the duty cycle. The characteristic curve shifts to lower cur-
rents accordingly (fig. 13).
Figure 13: Characteristic curve of a laser diode in (a) CW operation or

(b) pulsed operation
There are some other parameters of the laser diode that are tem-
perature depending. One of them is the lifetime of laser diodes. When
the chip temperature is reduced by about 10 degrees, the lifetime will
double. This is why the laser chip should at least be mounted to a heat
sink to avoid an overheating by power dissipation.
It is important to be aware of possible temperature effects on the

spectral distribution: With increasing temperature the crystal will ex-
tend and thus the resonator length will get larger. At the same time the
refractive index increases. By this, the single spectral lines drift to
longer wavelengths (fig. 14).

Figure 14: Temperature dependency of the mode spectrum of a gain guided laser diode
The amplification profile (= envelope of the spectrum) also shifts to

longer wavelengths as the band gap decreases with increasing tem-
perature.
For the wavelength drift of Fabry-Perot lasers the following tempera- temperature coefficients
ture coefficients can be stated:
δλ ì0,24nm / K ü δλ ìï0,12nm / K GaAlAs − lasers

≈í ý ≈í
δT envelope î0,30nm / K þ δT line ïî0,08nm / K InGaAsP − lasers
Since the temperature coefficients for the envelope curve and the sin-
gle spectral lines are different, mode hoppings result from changes in
temperature.
This effect is clearly visible with the index guided Fabry-Perot lasers,
where the envelope curve covers only one single spectral line. As the
envelope is moving faster than the spectral lines, at certain tempera-
tures the emitted wavelength jumps from one spectral line to the next
(see fig. 15). If the temperature is kept constant exactly where the
spectral line jumps, an irregular mode hopping between the two possi-
ble wavelengths occurs.

Figure 15: Temperature depending mode hoppings of an index guided

Fabry-Perot laser
The slopes of the single parts of the curve corresponds to the tem-
perature coefficient of the spectral lines. The changeover to the next
part of the curve corresponds to the hopping to the neighbour mode
caused by the shift of the amplification profile. However, at lower
powers the index guided Fabry-Perot laser shows several modes in
most cases (fig. 16).
Figure 16: Spectrum of an index guided Fabry-Perot laser
With DFB lasers the shift of the envelope curve can be neglected
since the envelope curve is very wide and the distance to potential
further modes is rather far. This means that the temperature depen-
dency of the spectrum of the DFB laser is only determined by the shift
of the single spectral line.
The corresponding temperature coefficient of a DFB laser is approxi-

mately 0,02nm/K to 0,1nm/K, which is much lower than that of a Fa-
bry-Perot laser. Since there is no envelope curve effect the DFB laser
does not show any mode hoppings.
In singlemode fibers the temperature drift of the wavelength causes

another annoying effect: the wavelength is drifting away from the zero
crossing of the dispersion. This results in a higher dispersion and
leads to a reduction of bandwidth.

Therefore it is necessary to stabilise the laser temperature. The

temperature is controlled thermoelectrically via a thermistor and a TE
cooler that enable heating or cooling of the laser diode.
For this purpose Profile offers numerous thermoelectric temperature

controllers (see chapter 6).
TE cooling is costly and makes the laser diode expensive. Therefore it

has been tried since long to develop lasers with less temperature de-
pendency. For applications in telecommunication an operating tem-
perature of -40°C to +85°C is required.
A breakthrough in reducing the temperature dependency was reached quantum well laser
by using the so-called distorted Quantum-Well (QW) layers as laser
active zone. These structures enable an operation without cooling up
to +85°.
Besides temperature control it is also possible to control the optical

output power (see chapter 6). For this purpose a photodiode (moni-
tor diode) is mounted opposite to the backfacet of the laser.
The laser diode, the monitor diode, the thermistor and the TE cooler
are installed in an hermetically closed package (refer to chapter 7).
The complete device is called laser module (fig. 17).
Figure 17: Set-up of a laser module

4.5 Modulation behaviour
Laser diodes can either be driven unmodulated, i.e. continuous wave - analog modulation
(CW) or modulated. For analog transmission the modulation is done in
the linear range of the characteristic curve. The operating point has to
be chosen accordingly.
At lower frequencies digital modulation is generated by a TTL signal digital modulation

(transistor-transistor-logic) that is added to a bias current below the la-
ser threshold.
For modulation frequencies in the GHz range the digital modulation is

done by an ECL (emitter-coupled-logic) signal that is added to a bias
current above the laser threshold.
So-called pulse laser diodes are driven in quasi continuous wave (QCW). QCW laser diodes
Rather long time intervals are between the single pulses. Duty cycles
of less than 1:100 are typical.
Since the average power decides how much a laser mirror can stand,
with QCW laser diodes much higher pulse powers can be achieved
than with modulated or unmodulated CW laser diodes.
If a QCW laser diode is driven cw, this will inevitably destroy the laser
due to overheating as the QCW laser provides a bad thermal contact
to the heat sink.
When modulating the laser diode (intensity modulation) the wave-

length of the laser changes due to the coupling of amplitude and
phase.
This unintended frequency modulation can broaden the spectrum

remarkably and can result in signal distortions.
(a) (b)
Figure 18: Spectrum of a Fabry-Perot laser (a) in CW mode or (b) modulated
DFB lasers remain singlemode in modulation and show, especially at

higher modulation frequencies, less broadening of the spectrum than
Fabry-Perot lasers.
At high data rates signal distortions can be extremely annoying. In that

case the laser is driven in CW mode and modulated externally with an
electro-optical modulator. The remaining broadening of the linewidth is e/o-modulator
proportional to the date rate only (equation 3).

4.6 Noise and backreflections
Laser diodes are sensitive against noise resulting from various origins. noise sources
Most of these noise sources can be controlled and thus the total noise
in the laser system can be limited. The four main noise sources are:
mode hoppings, amplitude intensity noise, optical feedback and
speckle noise.
Mode hoppings from one longitudinal mode to the next provoke a

jump in the output wavelength. As explained in chapter 4.4, mode
hoppings result from temperature changes in the active zone.
The shift of the output wavelength is accompanied by a short noise pe-

riod. This effect only occurs with Fabry-Perot lasers, not with DFB la-
sers.
Amplitude intensity noise is a function of the operating current. It is

the result of irregular changeover of electrons in the spontaneous as
well as in the stimulated phase of emission.
The interaction between photons and charge carriers in the active

zone creates an inner amplitude noise. This strongly decreases above
the threshold.
When selecting the current source to operate the laser diode, special
attention should be paid to low noise specifications.
Optical feedback results from back reflection of laser light into the la-
ser resonator at optical components as, for example, connectors. An
external resonator builds up, competing with the internal laser reso-
nator.
This external resonator is instable, so that the amplitude and phase

deviations due to the optical feedback lead to a broad-band noise. Es-
pecially index guided lasers with their small spectrum are very sensi-
tive to optical feedbacks.
In transmission systems where index guided lasers are used, optical

backreflections must be minimized. This is possible by using special
connectors, the high-return-loss connectors, which - due to angle po-
lished endfaces and a physical contact - only provoke very low reflec-
tion.
If backreflections cannot be avoided, an optical isolator must be in-

stalled directly behind the laser chip. This isolator provides a low in-
sertion loss from the laser to the fiber and a high insertion loss i the
back direction.
Speckle noise occurs strongest with lasers with a large coherence

length.

Table 1 compares the most important properties of LEDs and laser di-
odes. Table 2 compares some properties of Fabry-Perot lasers to DFB
lasers.
LED Laser diode

Wide beam, incoherent light Narrow beam, coherent light
Easy to handle Requires current and temperature
control
Frequency modulation up to Frequency modulation up to
several 100MHz 10GHz
Spectral width 30nm to 100nm Spectral width < 5nm
Optical power up to 1mW Optical power up to some 100mW
inexpensive Expensive
Bad linearity Good linearity
Table 1: Comparison of lasers diode with luminescence diodes
Properties Fabry-Perot laser DFB laser

Emission React sensitive to tem- Remain stable in wavelength,
behaviour perature changes with always singlemode, can be
mode hoppings tuned electronically
Spectral width Wide => higher chromatic Narrow => smaller chromatic
dispersion dispersion
Spectrum Emitting in multi-mode Emitting in singlemode when
when RF modulated RF modulated
Temperature high Insignificant
dependency
Table 2: Comparison of Fabry-Perot and DFB lasers
5 Precautions in handling a laser diode
Ideal conditions provided, laser diodes show a high reliability and

reach a lifetime of some 100.000 hours. They are, however, extremely
sensitive to electrostatic discharge, to exceeding the maximum al-
lowed laser current reverse breakdown voltage and to current spikes.
A reduction of output power, a shift of the laser threshold or a changed

beam divergence indicate a damage of the laser diode. If the beam
can no longer be focused sharply or when the lasers only emits like an
LED the laser is damaged as well.
Laser diodes can be damaged by a multitude of mechanisms. First of

all they are very sensitive against fast overshoots like short electric
transients, electrostatic discharge as well as operating the laser with
too high injection currents.
With a typical 5 mW laser the light intensity at the emitting area (2µm x
2 4
4µm) is 625 W/mm . A damage will occur when the intensity is 10
2
W/mm or more.
5 Precautions in handling a laser diode 19

The required protections are substantial and should be adhered ac- protections
cording to the instructions given by the manufacturer. The electrostatic
discharge caused by human touch is the most frequent cause for the
premature failure of the laser diode.
Latent damages that cannot be realised immediately will lead to a fast

altering of the laser diode. This is very critical for applications where a
long lifetime of the laser is required.
6 Laser diode controllers
To drive a laser diode save and stable a precise current source is

required. This current source must also provide numerous protections
functions: a slow increase of the laser current (softstart), protections
against transients to block any kind of line disturbances, interlock con-
trol for the connection cable to the laser diode and a safe adjustable
limit for the injection current.
Figure 19: Current source LDC 210 and temperature controller TED 200
of Profile for safe and stable control of a DIL-14 laser diode
Furthermore, the current source must be especially low noise and

must provide both operating modes constant current (the injection cur-
rent is kept constant) and constant power (the optical output power of
the laser is kept constant).
Profile GmbH offers a wide variety of suitable current sources for low,
medium and high-power laser diodes. To stabilise the laser wave-
length several temperature controllers are available.
7 Laser diode packages
Laser diodes are available in different standard packages. The CAN-

package (TO-18: 9 mm diameter, TO-46: 5,6 mm diameter, TO-3) is a
hermetically closed package which contains a laser chip, a photodiode
at the back facet for power monitoring (monitor diode) and a heatsink
(fig. 20).
6 Laser diode controllers 20

Figure 20: Set-up of a CAN-package (TO-18 or TO-46)
The 14-pin dual-in-line (DIL-14) packages and the 14-pin butterfly

(BFY) packages are mainly used in telecommunication.
They contain a laser diode with already coupled to a singlemode fiber

(pigtail), a heatsink, a TE cooler, a thermistor and a monitor diode.
They have 14 electrical contacts. Usually the case is connected to the
laser chip via the anode.
Figure 21: DIL-14 package with laser diode, monitor diode

thermistor, TE cooler and fiber coupling
Laser diodes in butterfly packages are well suited for RF modulation.

Therefore, the case must be grounded. Because of the modulation
capabilities this package is mainly used with D-WDM systems (refer to
BN 8000 Basic Notes D-WDM systems).
7 Packages 21
8 Literature
[1] Profile Basic Notes BN 8000, "DWDM systems", 2000
8 Literature 22

Basic Diode Laser

Uploaded by

Copyright:

Available Formats

Basic Diode Laser

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Basic Diode Laser

Uploaded by

Copyright:

Available Formats

BN 1000

Profile Optische Systeme GmbH

Tel + 49 8131 5956 - 0

Tel +1 973 664-9385

Basics on laser diodes

Laser diodes are semiconductor devices emitting coherent light. They

Since their invention in 1963 the development of laser diodes has

Handling laser diodes requires utmost care to protect them against

1 Generating a coherent emission in the laser diode 3

Copyright 2000, Profile GmbH

1 Generating a coherent emission in the laser diode

Common laser diodes are always edge emitters. Recently, however,

This is due to the stimulated emission. The emitted stimulated pho-

Figure 1: Incoherent and coherent emission

To cause an amplification of the light by stimulated emission, the

1 Generating a coherent emission in the laser diode 3

This so-called density inversion can be reached through an extreme

The emission becomes coherent due to a selective feedback gene-

By multiple reflection, standing waves can build up for certain dis-

Figure 2: Fabry-Perot resonator

Figure 3: Amplification and resonant frequencies in the optical resonator

1 Generating a coherent emission in the laser diode 4

Laser operation is possible at those resonator frequencies (longitudi-

2 Types of laser diodes

Traditional laser diodes provide a horizontal resonator structure where

Index guided lasers provide an additional built-in refractive index pro-

2 Types of laser diodes 5

Figure 5: Schematic structure of a DFB laser

DFB lasers are very selective. Contrary to the Fabry-Perot resonator

Thus it is possible to realise very narrow-band lasers that result in

Figure 6: Vertical cavity surface emitting laser (VCSEL)

VCSELs typically emit with relatively large symmetric apertures. Thus

2 Types of laser diodes 6

Many other types of lasers with increasingly complicated structures

Another method is the set-up of laser bars (= arrays). Here several

Further applications for these components are, for example, point-to-

When coupled into a singlemode fiber with a very small numerical

The lasing wavelength is a function of the band gap and is determined

InGaAsP is mainly used to manufacture components in the 1300nm

InGaAlP is used for semiconductor lasers in the visible range starting

Up to now even lower wavelengths can only be realised with semicon-

Profile supplies convenient temperature controllers also for lead sul-

4 Characteristics and features of laser diodes

4.1 Characteristic curves

Above a characteristic threshold current IS, at which the laser diode

Figure 7: Characteristic curves of a LED and a laser diode

The linearity is characterised by a ratio of harmonics. Especially high

The slope of the characteristic curve, measured in mW/mA, is directly

4 Characteristics and features of laser diodes 8

4.2 Optical spectrum

The optical spectrum of a laser with Fabry-Perot resonator has already

Figure 8: Spectrums of laser diodes:

The coherence length lcoh of laser diodes is low. It can be calculated

Thus an index guided Fabry-Perot laser, emitting a single spectral line

4 Characteristics and features of laser diodes 9

There is the following relation between the phase velocity v, the

By differentiating from f(λ) to λ you get a relation between the line

Typical multimode lasers with a 3-db width of 2 nm to 3 nm corres- frequencies

4.3 Beam characteristics

As the active, light emitting area is shaped rectangular with strongly