Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 17 views

    RM-0181-03 - Cable - Unbalanced 3-Wire Remote Control

    Uploaded by

    Jose Jullian
    The document describes a 3-wire cable used for unbalanced RS-232 communication between a modem or other data terminal equipment and a PC. It lists the pin assignments for a 9-pin female connector on each end, with pin 1, 4, and 9 not connected in the electrical mode. The cable connects the "J1 REM CTRL" port of the modem to the "RS-232" port of a PC.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    RM-0181-03 - Cable - Unbalanced 3-Wire Remote Control

    Uploaded by

    Jose Jullian
    17 views1 page
    The document describes a 3-wire cable used for unbalanced RS-232 communication between a modem or other data terminal equipment and a PC. It lists the pin assignments for a 9-pin female connector on each end, with pin 1, 4, and 9 not connected in the electrical mode. The cable connects the "J1 REM CTRL" port of the modem to the "RS-232" port of a PC.

    Original Description:

    Control interface RM6

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document describes a 3-wire cable used for unbalanced RS-232 communication between a modem or other data terminal equipment and a PC. It lists the pin assignments for a 9-pin female connector on each end, with pin 1, 4, and 9 not connected in the electrical mode. The cable connects the "J1 REM CTRL" port of the modem to the "RS-232" port of a PC.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    17 views1 page

    RM-0181-03 - Cable - Unbalanced 3-Wire Remote Control

    Uploaded by

    Jose Jullian
    The document describes a 3-wire cable used for unbalanced RS-232 communication between a modem or other data terminal equipment and a PC. It lists the pin assignments for a 9-pin female connector on each end, with pin 1, 4, and 9 not connected in the electrical mode. The cable connects the "J1 REM CTRL" port of the modem to the "RS-232" port of a PC.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 1

    NOTE: (NC*) In RS-232 Electrical Mode

    these pins are not connected

    RCTRL_RX_B (NC*) 1 1 DCD Data Carrier Detect

    RCTRL_RX_A 2 2 RD Rx Data

    RCTRL_TX_A 3 3 TD Tx Data

    RM RCTRL_TX_B (NC*) 4 4 DTR Data Terminal Ready


    PC or
    Modem Control
    RCTRL_SIG_GND 5 5 SG Signal GND
    Equipment
    NC 6 6 DSR Data Set Ready

    NC 7 7 RTS Request To Send

    NC 8 8 CTS Clear To Send

    RCTRL_VCC (NC*) 9 9 RI Ring Indicator

    Connector Shield * Cable Shield

    Cable connector: DE9F: D-Sub 9-pin female, Cable connector: DE9F: D-Sub 9-pin female,
    connects to the “J1 REM CTRL” port connects to the “RS-232” port
    of the Modem or other DTE Equipment of a PC/laptop or similar device

    Equipment definition: ‘DTE’ Equipment definition: ‘DTE’

    RM-0181-03 - Cable - Unbalanced 3-wire Remote Control

    You might also like