VLT® AutomationDrive Programming Guide

MAKING MODERN LIVING POSSIBLE

Programming Guide
VLTp AutomationDrive
MG33MD22

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Contents FC 300 Programming Guide

Contents

1 Introduction 1-1
1.1.1 Approvals 1-1
1.1.2 Symbols 1-1
1.1.3 Abbreviations 1-1
1.1.4 Definitions 1-2
1.1.5 Electrical Wiring - Control Cables 1-6

2 How to Program 2-1

2.1 The Graphical and Numerical Local Control Panels 2-1
2.1.1 How to Program on the Graphical LCP 2-1
2.1.2 The LCD Display 2-1
2.1.4 Display Mode 2-4
2.1.5 Display Mode - Selection of Readouts 2-4
2.1.6 Parameter Set-up 2-5
2.1.7 Quick Menu Key Functions 2-5
2.1.9 Main Menu Mode 2-8
2.1.10 Parameter Selection 2-8
2.1.14 Infinitely Variable Change of Numeric Data Value 2-9
2.1.16 Readout and Programming of Indexed Parameters 2-9
2.1.17 How to Program on the Numerical Local Control Panel 2-9
2.1.18 Local Control Keys 2-11
2.1.19 Initialization to Default Settings 2-11

3 Parameter Descriptions 3-1

3.2 Parameters: 0-** Operation and Display 3-2
3.3 Parameters: 1-** Load and Motor 3-13
3.3.10.1 PTC Thermistor Connection 3-25
3.3.10.2 KTY Sensor Connection 3-25
3.3.10.3 ETR 3-26
3.3.10.4 ATEX ETR 3-26
3.3.10.5 Klixon 3-27
3.4 Parameters: 2-** Brakes 3-29
3.5 Parameters: 3-** Reference / Ramps 3-34
3.6 Parameters: 4-** Limits/Warnings 3-44
3.7 Parameters: 5-** Digital In/Out 3-49
3.8 Parameters: 6-** Analog In/Out 3-69
3.9 Parameters: 7-** Controllers 3-78
3.10 Parameters: 8-** Communications and Options 3-84

MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Contents FC 300 Programming Guide

3.11 Parameters: 9-** Profibus 3-94

3.12 Parameters: 10-** DeviceNet CAN Fieldbus 3-101
3.13 Parameters: 12-** Ethernet 3-105
3.14 Parameters: 13-** Smart Logic Control 3-110
3.15 Parameters: 14-** Special Functions 3-127
3.16 Parameters: 15-** Drive Information 3-136
3.17 Parameters: 16-** Data Read-outs 3-141
3.18 Parameters: 17-** Motor Feedb. Option 3-148
3.19 Parameters: 18-** Data Readouts 2 3-150
3.20 Parameters: 30-** Special Features 3-151
3.21 Parameters: 35-** Sensor Input Option 3-154

4 Parameter Lists 4-1

4.1.1 Conversion 4-1
4.1.2 Active/Inactive Parameters in Different Drive Control Modes 4-2

5 Troubleshooting 5-1
5.1.1 Warnings/Alarm Messages 5-1

6 Index 6-1

MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Introduction FC 300 Programming Guide

1 1
1 Introduction

1.1.3 Abbreviations
Programming Guide
Software version: 6.5x Alternating current AC
American wire gauge AWG
This Programming Guide can be used for all FC 300 adjustable Ampere/AMP A
frequency drives with software version 6.5x. Automatic Motor Adaptation AMA
The software version number can be seen from 15-43 Software Current limit ILIM
Version. Degrees Celsius °C
Direct current DC
1.1.1 Approvals Drive Dependent D-TYPE
Electro Magnetic Compatibility EMC
Electronic Thermal Relay ETR
Adjustable frequency drive FC
Gram g
Hertz Hz
Horsepower hp
Kilohertz kHz
Local Control Panel LCP
Meter m
Millihenry Inductance mH
1.1.2 Symbols Milliampere mA
Millisecond ms
Symbols used in this guide.
Minute min
Motion Control Tool MCT
NOTE! Nanofarad nF
Indicates something to be noted by the reader. Newton Meters Nm
Nominal motor current IM,N

CAUTION Nominal motor frequency

Nominal motor power
fM,N
PM,N
Indicates a potentially hazardous situation which, if not
Nominal motor voltage UM,N
avoided, may result in minor or moderate injury or
equipment damage. Permanent Magnet motor PM motor
Protective Extra Low Voltage PELV
Printed Circuit Board PCB
WARNING Rated Inverter Output Current IINV
Indicates a potentially hazardous situation which, if not Revolutions Per Minute RPM
avoided, could result in death or serious injury. Regenerative terminals Regen
Second sec.
* Indicates default setting Synchronous Motor Speed ns
Torque limit TLIM
Volts V
The maximum output current IVLT,MAX
The rated output current supplied by the IVLT,N
Adjustable frequency drive

MG33MD22 - VLT® is a registered Danfoss trademark 1-1

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Introduction FC 300 Programming Guide

1 1
1.1.4 Definitions PM,N
Rated motor power (nameplate data in kW or HP).
Adjustable frequency drive:
IVLT,MAX TM,N
Maximum output current. Rated torque (motor).
IVLT,N
Rated output current supplied by the Adjustable frequency UM
drive. Instantaneous motor voltage.

UVLT, MAX
UM,N
Maximum output voltage.
Rated motor voltage (nameplate data).
Input:
Control command
Break-away torque
Start and stop the connected motor by means of LCP and
digital inputs.
Torque
Functions are divided into two groups.

175ZA078.10
Functions in group 1 have higher priority than functions in Pull-out

group 2.

Group 1 Reset, Coasting stop, Reset and Coasting stop,

Quick stop, DC braking, Stop and the [OFF] key.
Group 2 Start, Pulse start, Reversing, Start reversing, Jog
and Freeze output

Motor:
Motor Running
Torque generated on output shaft and speed from zero
rpm to max. speed on motor.
rpm
fJOG
Motor frequency when the jog function is activated (via
digital terminals). ηVLT
fM The efficiency of the Adjustable frequency drive is defined
Motor frequency. as the ratio between the power output and the power
input.
fMAX
Maximum motor frequency.
Start-disable command
fMIN A stop command belonging to the group 1 control
Minimum motor frequency. commands - see this group.
fM,N
Rated motor frequency (nameplate data). Stop command
IM See Control commands.
Motor current (actual).
References:
IM,N
Analog Reference
Rated motor current (nameplate data).
A signal transmitted to the analog inputs 53 or 54, can be
nM,N voltage or current.
Rated motor speed (nameplate data).
Binary Reference
ns A signal transmitted to the serial communication port.
Synchronous motor speed
Preset Reference
A defined preset reference to be set from -100% to +100%
2 × par . 1 − 23 × 60 s
ns = of the reference range. Selection of eight preset references
par . 1 − 39
via the digital terminals.

1-2 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Introduction FC 300 Programming Guide

1 1
Pulse Reference Initializing
A pulse frequency signal transmitted to the digital inputs If initialization is carried out (14-22 Operation Mode), the
(terminal 29 or 33). Adjustable frequency drive returns to the default setting.
RefMAX Intermittent Duty Cycle
Determines the relationship between the reference input An intermittent duty rating refers to a sequence of duty
at 100% full scale value (typically 10 V, 20 mA) and the cycles. Each cycle consists of an on-load and an off-load
resulting reference. The maximum reference value set in period. The operation can be either periodic duty or non-
3-03 Maximum Reference. periodic duty.
RefMIN LCP
Determines the relationship between the reference input The Local Control Panel makes up a complete interface for
at 0% value (typically 0 V, 0 mA, 4 mA) and the resulting control and programming of the Adjustable frequency
reference. The minimum reference value set in drive. The control panel is detachable and can be installed
3-02 Minimum Reference. up to 10 ft [3 m] from the Adjustable frequency drive, i.e.,
in a front panel by means of the installation kit option.
Miscellaneous:
Analog Inputs lsb
The analog inputs are used for controlling various Least significant bit.
functions of the Adjustable frequency drive. msb
There are two types of analog inputs: Most significant bit.
Current input, 0-20 mA and 4-20 mA
Voltage input, 0-10 V DC (FC 301) MCM
Voltage input, -10 - +10 V DC (FC 302FC 102). Short for Mille Circular Mil, an American measuring unit for
cable cross-section. 1 MCM = 0.5067 mm2.
Analog Outputs
The analog outputs can supply a signal of 0–20 mA, 4–20 Online/Offline Parameters
mA. Changes to online parameters are activated immediately
after the data value is changed. Changes to offline
Automatic Motor Adaptation, AMA
parameters are not activated until you enter [OK] on the
AMA algorithm determines the electrical parameters for
LCP.
the connected motor at standstill.
Process PID
Brake Resistor
The PID control maintains the desired speed, pressure,
The brake resistor is a module capable of absorbing the
temperature, etc. by adjusting the output frequency to
braking energy generated in regenerative braking. This
match the varying load.
regenerative braking energy increases the intermediate
circuit voltage and a brake chopper ensures that the PCD
power is transmitted to the brake resistor. Process Control Data

CT Characteristics Power Cycle

Constant torque characteristics used for all applications Switch off line power until the display (LCP) is dark – then
such as conveyor belts, displacement pumps and cranes. turn power on again.

Digital Inputs Pulse Input/Incremental Encoder

The digital inputs can be used for controlling various An external, digital pulse transmitter used for feeding back
functions of the Adjustable frequency drive. information on motor speed. The encoder is used in
applications where great accuracy in speed control is
Digital Outputs
required.
The Adjustable frequency drive features two solid state
outputs that can supply a 24 V DC (max. 40 mA) signal. RCD
Residual Current Device.
DSP
Digital Signal Processor. Set-up
You can save parameter settings in four set-ups. Change
ETR
between the four parameter set-ups, and edit one set-up,
Electronic Thermal Relay is a thermal load calculation
while another set-up is active.
based on present load and time. Its purpose is to estimate
the motor temperature. SFAVM
Switching pattern called Stator Flux oriented Asynchronous
Hiperface® Vector Modulation (14-00 Switching Pattern).
Hiperface® is a registered trademark by Stegmann.

MG33MD22 - VLT® is a registered Danfoss trademark 1-3

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Introduction FC 300 Programming Guide

1 1
Slip Compensation Power Factor
The Adjustable frequency drive compensates for the motor The power factor is the relation between I1 and IRMS.
slip by giving the frequency a supplement that follows the
measured motor load keeping the motor speed almost 3 x U x I 1 cos ϕ
Power factor =
constant. 3 x U x I RMS

Smart Logic Control (SLC) The power factor for 3-phase control:
The SLC is a sequence of user-defined actions executed
when the associated user-defined events are evaluated as I 1 x cos ϕ1 I1
= = since cos ϕ1 = 1
I RMS I RMS
true by the Smart Logic Controller. (Par. group 13-** Smart
Logic Control (SLC). The power factor indicates to which extent the Adjustable
frequency drive imposes a load on the line power supply.
STW
The lower the power factor, the higher the IRMS for the
Status Word
same hp [kW] performance.
FC Standard Bus
Includes RS-485 bus with FC protocol or MC protocol. See I RMS = I 12 + I 52 + I 72 + .. + I n2
8-30 Protocol.
In addition, a high power factor indicates that the different
Thermistor harmonic currents are low.
A temperature-dependent resistor placed where the The adjustable frequency drive's built-in DC coils produce a
temperature is to be monitored (Adjustable frequency high power factor, which minimizes the imposed load on
drive or motor). the line power supply.
Trip
A state entered in fault situations, e.g., if the Adjustable WARNING
frequency drive is subject to an over-temperature or when The voltage of the Adjustable frequency drive is dangerous
the Adjustable frequency drive is protecting the motor, whenever connected to line power. Incorrect installation of
process or mechanism. Restart is prevented until the cause the motor, Adjustable frequency drive or serial communi-
of the fault has disappeared and the trip state is cancelled cation bus may cause death, serious personal injury or
by activating reset or, in some cases, by being damage to the equipment. Consequently, the instructions
programmed to reset automatically. Trip may not be used in this manual, as well as national and local rules and
for personal safety. safety regulations, must be complied with.

Trip Locked
A state entered in fault situations when the Adjustable Safety Regulations
frequency drive is protecting itself and requiring physical 1. The line power supply to the Adjustable
intervention, e.g., if the Adjustable frequency drive is frequency drive must be disconnected whenever
subject to a short circuit on the output. A locked trip can repair work is to be carried out. Make sure that
only be canceled by cutting off line power, removing the the line power supply has been disconnected and
cause of the fault, and reconnecting the Adjustable that the necessary time has elapsed before
frequency drive. Restart is prevented until the trip state is removing motor and line power supply plugs.
cancelled by activating reset or, in some cases, by being 2. The [OFF] button on the control panel of the
programmed to reset automatically. Trip may not be used Adjustable frequency drive does not disconnect
for personal safety. the line power supply and consequently it must
VT Characteristics not be used as a safety switch.
Variable torque characteristics used for pumps and fans. 3. The equipment must be properly grounded, the
user must be protected against supply voltage
VVCplus
and the motor must be protected against
If compared with standard voltage/frequency ratio control,
overload in accordance with applicable national
Voltage Vector Control (VVCplus ) improves the dynamics
and local regulations.
and the stability, both when the speed reference is
changed and in relation to the load torque. 4. The ground leakage current exceeds 3.5 mA.
5. Protection against motor overload is not included
60° AVM in the factory setting. If this function is desired,
Switching pattern called 60° Asynchronous Vector set 1-90 Motor Thermal Protection to data value
Modulation (14-00 Switching Pattern). ETR trip 1 [4] or data value ETR warning 1 [3].

1-4 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Introduction FC 300 Programming Guide

1 1
6. Do not remove the plugs for the motor and line activated in error, be delayed or fail to occur
power supply while the Adjustable frequency entirely. When used in situations where safety is
drive is connected to line power. Make sure that critical, e.g., when controlling the electromagnetic
the line power supply has been disconnected and brake function of a hoist application, these
that the necessary time has elapsed before control signals must not be relied on exclusively.
removing motor and line power plugs.
7. Please note that the Adjustable frequency drive
WARNING
has more voltage sources than L1, L2 and L3, High Voltage
when load sharing (linking of DC intermediate Touching the electrical parts may be fatal - even after the
circuit) or external 24 V DC are installed. Make equipment has been disconnected from line power.
sure that all voltage sources have been discon- Also make sure that other voltage inputs have been
nected and that the necessary time has elapsed disconnected, such as external 24V DC, load sharing
before commencing repair work. (linkage of DC intermediate circuit), as well as the motor
connection for kinetic backup.
Warning against unintended start
Systems where adjustable frequency drives are installed
1. The motor can be brought to a stop by means of
must, if necessary, be equipped with additional monitoring
digital commands, bus commands, references or
and protective devices according to the valid safety
a local stop, while the Adjustable frequency drive
regulations, e.g., law on mechanical tools, regulations for
is connected to line power. If personal safety
the prevention of accidents, etc. Modifications on the
considerations (e.g., risk of personal injury caused
adjustable frequency drives by means of the operating
by contact with moving machine parts following
software are allowed.
an unintentional start) make it necessary to
ensure that no unintended start occurs, these
stop functions are not sufficient. In such cases, NOTE!
the line power supply must be disconnected or Hazardous situations shall be identified by the machine
the Safe Stop function must be activated. builder/ integrator who is responsible for taking necessary
preventive means into consideration. Additional
2. The motor may start while setting the
monitoring and protective devices may be included, always
parameters. If this means that personal safety
according to valid national safety regulations, e.g., law on
may be compromised (e.g., personal injury caused
mechanical tools, regulations for the prevention of
by contact with moving machine parts), motor
accidents.
starting must be prevented, for instance by use
of the Safe Stop function or secure disconnection
of the motor connection. NOTE!
Crane, Lifts and Hoists:
3. A motor that has been stopped with the line
The controlling of external brakes must always have a
power supply connected may start if faults occur
redundant system. The Adjustable frequency drive can in
in the electronics of the Adjustable frequency
no circumstances be the primary safety circuit. Comply
drive through temporary overload or if a fault in
with relevant standards, e.g.,
the power supply grid or motor connection is
Hoists and cranes: IEC 60204-32
remedied. If unintended start must be prevented
Lifts: EN 81
for personal safety reasons (e.g., risk of injury
caused by contact with moving machine parts),
the normal stop functions of the Adjustable Protection Mode
frequency drive are not sufficient. In such cases, Once a hardware limit on motor current or DC link voltage
the line power supply must be disconnected or is exceeded, the Adjustable frequency drive will enter
the Safe Stop function must be activated. “Protection mode”. “Protection mode” means a change of
the PWM modulation strategy and a low switching
NOTE! frequency to minimize losses. This continues 10 sec after
When using the Safe Stop function, always follow the the last fault and increases the reliability and the
instructions in the section Safe Stop of the VLT robustness of the Adjustable frequency drive while re-
AutomationDrive Design Guide. establishing full control of the motor.
In hoist applications, “protection mode” is not usable
4. Control signals from or internally within the because the Adjustable frequency drive will usually not be
Adjustable frequency drive may in rare cases be able to leave this mode again and therefore it will extend
the time before activating the brake – which is not
recommended.

MG33MD22 - VLT® is a registered Danfoss trademark 1-5

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Introduction FC 300 Programming Guide

1 1
The “protection mode” can be disabled by setting NOTE!
14-26 Trip Delay at Inverter Fault to zero which means that It is recommended to disable protection mode in hoisting
the Adjustable frequency drive will trip immediately if one applications (14-26 Trip Delay at Inverter Fault = 0)
of the hardware limits is exceeded.

1.1.5 Electrical Wiring - Control Cables

Figure 1.1 Diagram showing all electrical terminals without options.

Terminal 37 is the input to be used for Safe Stop. For instructions on Safe Stop installation please, refer to the section Safe Stop Instal-
lation of the Design Guide.
* Terminal 37 is not included in FC 301 (Except FC 301 A1, which includes Safe Stop).
Terminal 29 and Relay 2, are not included in FC 301.

1-6 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Introduction FC 300 Programming Guide

1 1
In rare cases, and depending on the installation, very long control cables and analog signals may result in 50/60 Hz ground
loops due to noise from line power supply cables.

If this occurs, it may be necessary to break the shield or insert a 100 nF capacitor between shield and chassis.

The digital and analog inputs and outputs must be connected separately to the common inputs (terminal 20, 55, 39) of the
Adjustable frequency drive to avoid ground currents from both groups to affect other groups. For example, switching on
the digital input may disturb the analog input signal.

Input polarity of control terminals

130BA681.10
PNP (Source) 130BT106.10
+24 V DC

Digital input wiring

0 VDC

12 13 18 19 27 29 32 33 20 37
130BT107.11
+24 V DC

0 VDC

NPN (Sink)
Digital input wiring

12 13 18 19 27 29 32 33 20 37
1.1.6 Start/Stop

Terminal 18 = 5-10 Terminal 18 Digital Input [8] Start

Terminal 27 = 5-12 Terminal 27 Digital Input [0] No
operation (Default coast inverse)
Terminal 37 = Safe stop (where available)

NOTE!
Control cables must be shielded/armored.

See section on grounding of shielded/armored control

cables in the Design Guide for the correct termination of
control cables.

MG33MD22 - VLT® is a registered Danfoss trademark 1-7

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Introduction FC 300 Programming Guide

1 1
1.1.8 Speed Up/Down

Terminals 29/32 = Speed up/down

Terminal 18 = 5-10 Terminal 18 Digital Input Start
[9] (default)
Terminal 27 = 5-12 Terminal 27 Digital Input
Freeze reference [19]
Terminal 29 = 5-13 Terminal 29 Digital Input
Speed up [21]
Terminal 32 = 5-14 Terminal 32 Digital Input Slow
[22]
NOTE: Terminal 29 only in FC x02 (x=series type).

130BA021.12
12 +24V

18 Par. 5-10
1.1.7 Pulse Start/Stop
27 Par. 5-12
Terminal 18 = 5-10 Terminal 18 Digital InputLatched start,
[9]
Terminal 27= 5-12 Terminal 27 Digital InputStop inverse, [6]
29 Par. 5-13
Terminal 37 = Safe stop (where available)

32 Par. 5-14

37

1.1.9 Potentiometer Reference

Voltage reference via a potentiometer

Reference Source 1 = [1] Analog input 53 (default)
Terminal 53, Low Voltage = 0V
Terminal 53, High Voltage = 10V
Terminal 53, Low Ref./Feedback = 0 RPM
Terminal 53, High Ref./Feedback = 1500 RPM
Switch S201 = OFF (U)

1-8 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Introduction FC 300 Programming Guide

1 1

MG33MD22 - VLT® is a registered Danfoss trademark 1-9

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Introduction FC 300 Programming Guide

1 1

1-10 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 How to Program FC 300 Programming Guide

2 How to Program
2 2

130BA018.13
2.1 The Graphical and Numerical Local
Control Panels
Status 1(0) a
The easiest programming of the Adjustable frequency
1234rpm 10,4A 43,5Hz
drive is performed by the Graphical LCP (LCP 102). It is
necessary to consult the Adjustable frequency drive Design
Guide, when using the Numeric Local Control Panel (LCP 1 b
101). 43,5Hz

2.1.1 How to Program on the Graphical c

Run OK
LCP

The following instructions are valid for the graphical 2 Status

Quick Main Alarm
Menu Menu Log
LCP(LCP 102)

The control panel is divided into four functional groups.

1. Graphical display with Status lines.

Ca
ck

n
Ba

ce
l
2. Menu keys and LEDs - changing parameters and
switching between display functions.
3. Navigation keys and LEDs (LEDs).

Info
3 On OK
4. Operation keys and LEDs.
Warn.
All data is displayed in a graphical LCP display, which can
show up to five items of operating data while displaying Alarm
[Status].

Hand Auto
Display lines 4
on Off on Reset
a. Status line: Status messages displaying icons and
graphic.
b. Line 1-2: Operator data lines displaying data
defined or chosen by the user. By pressing the 2.1.2 The LCD Display
[Status] key, up to one extra line can be added.
The LCD display has back lighting and a total of 6 alpha-
c. Status line: Status messages displaying text.
numeric lines. The display lines show the direction of
rotation (arrow), the chosen Set-up as well as the
programming Set-up. The display is divided into three
sections.

Top section shows up to two measurements in normal

operating status.

The top line in the Middle section shows up to five

measurements with related unit, regardless of status
(except in the case of alarm/warning).

The bottom section always shows the state of the

Adjustable frequency drive in status mode.

MG33MD22 - VLT® is a registered Danfoss trademark 2-1

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 How to Program FC 300 Programming Guide

The control keys are divided into functions. The keys

130BP074.10
2 2
Status ! 1(1)
Top section below the display and LEDs are used for parameter set-up,
43 RPM 5.44 A 25.3 kW
including choice of display indication during normal
1.4 Hz operation.
Middle section
2.9%

130BP045.10
Quick Main Alarm
! Pwr.card temp (W29) Status
Menu Menu Log
Bottom section
Auto Remote Running

[Status] indicates the status of the Adjustable frequency

The Active Set-up (selected as the Active Set-up in
drive and/or the motor. Choose between three different
0-10 Active Set-up) is shown. When programming another
readouts by pressing the [Status] key: Five line readouts,
set-up than the active set-up, the number of the
four line readouts or Smart Logic Control.
programmed set-up appears to the right.
Use [Status] for selecting the mode of display or for
changing back to display mode from either the quick
Display Contrast Adjustment menu mode, the main menu mode or alarm mode. Also
use the [Status] key to toggle single or double readout
Press [status] and [▲] for darker display mode.
Press [status] and [▼] for brighter display
[Quick Menu] allows quick access to different quick menus
Most parameter set-ups can be changed immediately via such as
the LCP, unless a password has been created via 0-60 Main
Menu Password or via 0-65 Quick Menu Password. • My Personal Menu

• Quick Set-up
LEDs
• Changes Made

If certain threshold values are exceeded, the alarm and/or • Loggings

warning LED lights up. A status and alarm text appear on Use [Quick Menu] for programming the parameters
the LCP. belonging to the Quick Menu. It is possible to switch
The ON LED is activated when the Adjustable frequency directly between Quick Menu mode and Main Menu mode.
drive receives AC line voltage or via a DC bus terminal or
24V external supply. At the same time, the back light is on.
[Main Menu] is used for programming all parameters.
It is possible to switch directly between Main Menu mode
• Green LED/On: Control section is working. and Quick Menu mode.
• Yellow LED/Warn.: Indicates a warning. Parameter shortcut can be carried out by pressing down
the [Main Menu] key for 3 seconds. The parameter shortcut
• Flashing Red LED/Alarm: Indicates an alarm.
allows direct access to any parameter.
130BP044.10

[Alarm Log] displays an alarm list of the five latest alarms

(numbered A1-A5). To obtain additional details about an
On alarm, use the arrow keys to navigate to the alarm number
and press [OK]. You will now receive information about the
condition of your Adjustable frequency drive right before

Warn. entering alarm mode.

[Back] takes you to the previous step or layer in the

Alarm navigation structure.

[Cancel] annuls your last change or command as long as

LCP Keys the display has not been changed.

2-2 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 How to Program FC 300 Programming Guide

[Info] supplies information about a command, parameter, • DC brake

or function in any display window. [Info] provides detailed
information whenever help is needed.
[Off] stops the connected motor. The key can be selected 2 2
as Enable [1] or Disable [0] via 0-41 [Off] Key on LCP. If no
Exit info mode by pressing either [Info], [Back], or [Cancel].
external stop function is selected and the [Off] key is
inactive, the motor can be stopped by disconnecting the
voltage.
Back

[Auto On] enables the Adjustable frequency drive to be

controlled via the control terminals and/or serial communi-
cation. When a start signal is applied on the control
Cancel terminals and/or the bus, the Adjustable frequency drive
will start. The key can be selected as Enable [1] or Disable
[0] via 0-42 [Auto on] Key on LCP.

Info NOTE!
An active HAND-OFF-AUTO signal via the digital inputs has
higher priority than the control keys [Hand on] – [Auto on].
Navigation Keys
The four navigation arrows are used to navigate between [Reset] is used for resetting the Adjustable frequency drive
the different choices available in [Quick Menu], [Main after an alarm (trip). It can be selected as Enable [1] or
Menu] and [Alarm Log]. Use the keys to move the cursor. Disable [0] via 0-43 [Reset] Key on LCP.

[OK] is used for choosing a parameter marked by the The parameter shortcut can be carried out by holding
cursor and for enabling the change of a parameter. down the [Main Menu] key for 3 seconds. The parameter
shortcut allows direct access to any parameter.
Local Control Key for local control is found at the bottom
of the LCP. 2.1.3 Quick Transfer of Parameter Settings
between Multiple Adjustable
Frequency Drives
130BP046.10

Hand
Off
Auto
Reset Once the set-up of a Adjustable frequency drive is
on on
complete, we recommend that you store the data in the
LCP or on a PC via MCT 10 Set-up Software Tool.

[Hand On] enables control of the Adjustable frequency

130BA027.10

drive via the LCP. [Hand on] also starts the motor, and it is
Alarm
now possible to enter the motor speed data by means of Status
Quick Main
Log
Menu Menu
the arrow keys. The key can be selected as Enable [1] or
Disable [0] via 0-40 [Hand on] Key on LCP
External stop signals activated by means of control signals
Ca

or a serial bus will override a “start” command via the LCP.

ck

n
Ba

ce
l

The following control signals will still be active when

[Hand on] is activated.
Info

On OK
• [Hand on] - [Off] - [Auto on]

• Reset Warn.

• Coasting stop inverse Alarm

• Reversing

• Hand Auto
Set-up select bit 0 - Set-up select bit 1 on
Off on Reset

• Stop command from serial communication

• Quick stop

MG33MD22 - VLT® is a registered Danfoss trademark 2-3

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 How to Program FC 300 Programming Guide

Data storage in LCP digits after a possible decimal point. The larger the
2 2 1. Go to 0-50 LCP Copy numeric value for a parameter, the fewer digits displayed
after the decimal point.
2. Press the [OK] key
Ex.: Current readout 5.25A; 15.2A 105A.
3. Select “All to LCP”
4. Press the [OK] key Operating variable: Unit:
All parameter settings are now stored in the LCP indicated 16-00 Control Word hex
by the progress bar. When 100% is reached, press [OK]. 16-01 Reference [Unit] [unit]
16-02 Reference [%] %

NOTE! 16-03 Status Word hex

16-05 Main Actual Value [%] %
Stop the motor before performing this operation.
16-10 Power [kW] [kW]
16-11 Power [hp] [HP]
Connect the LCP to another Adjustable frequency drive
16-12 Motor Voltage [V]
and copy the parameter settings to this Adjustable
16-13 Frequency [Hz]
frequency drive as well.
16-14 Motor Current [A]
16-16 Torque [Nm] Nm
Data transfer from LCP to Adjustable frequency drive
16-17 Speed [RPM] [RPM]
1. Go to 0-50 LCP Copy
16-18 Motor Thermal %
2. Press the [OK] key 16-20 Motor Angle
3. Select “All from LCP” 16-30 DC Link Voltage V
4. Press the [OK] key 16-32 Brake Energy /s kW
16-33 Brake Energy /2 min kW
The parameter settings stored in the LCP are now
16-34 Heatsink Temp. C
transferred to the Adjustable frequency drive indicated by
16-35 Inverter Thermal %
the progress bar. When 100% is reached, press [OK].
16-36 Inv. Nom. Current A
16-37 Inv. Max. Current A
NOTE! 16-38 SL Controller State
Stop the motor before performing this operation. 16-39 Control Card Temp. C
16-40 Logging Buffer Full
2.1.4 Display Mode 16-50 External Reference
16-51 Pulse Reference
In normal operation, up to 5 different operating variables 16-52 Feedback [Unit] [Unit]
can be indicated continuously in the middle section: 1.1, 16-53 Digi Pot Reference
1.2, and 1.3 as well as 2 and 3. 16-60 Digital Input bin
16-61 Terminal 53 Switch Setting V
2.1.5 Display Mode - Selection of Readouts 16-62 Analog Input 53
16-63 Terminal 54 Switch Setting V
It is possible to toggle between three status readout 16-64 Analog Input 54
screens by pressing the [Status] key. 16-65 Analog Output 42 [mA] [mA]
Operating variables with different formatting are shown in 16-66 Digital Output [bin] [bin]
each status screen - see below.
16-67 Pulse Input #29 [Hz] [Hz]
16-68 Freq. Input #33 [Hz] [Hz]
Table 2.1 shows the measurements you can link to each of 16-69 Pulse Output #27 [Hz] [Hz]
the operating variables. When Options are mounted,
16-70 Pulse Output #29 [Hz] [Hz]
additional measurements are available. Define the links via
16-71 Relay Output [bin]
0-20 Display Line 1.1 Small, 0-21 Display Line 1.2 Small,
16-72 Counter A
0-22 Display Line 1.3 Small, 0-23 Display Line 2 Large, and
16-73 Counter B
0-24 Display Line 3 Large.
16-80 Fieldbus CTW 1 hex
16-82 Fieldbus REF 1 hex
Each readout parameter selected in 0-20 Display Line 1.1
16-84 Comm. Option STW hex
Small to 0-24 Display Line 3 Large has its own scale and

2-4 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 How to Program FC 300 Programming Guide

Operating variable: Unit:

130BP063.10
2 2
Status 1 (1)
16-85 FC Port CTW 1 hex 778 RPM 0.86 A 4.0 kW
16-86 FC Port REF 1 hex
16-90 Alarm Word State: 0 off 0 (off )
When: -
16-92 Warning Word Do: -
16-94 Ext. Status Word
Auto Remote Running

Status screen I
This readout state is standard after start-up or initialization. 2.1.6 Parameter Set-up
Use [INFO] to obtain information about the measurement
links to the displayed operating variables (1.1, 1.2, 1.3, 2 The Adjustable frequency drive can be used for practically
and 3). all assignments, which is why the number of parameters is
See the operating variables shown in the screen below. quite large. The Adjustable frequency drive offers a choice
between two programming modes - a Main Menu and a
Quick Menu mode.
130BP041.10

Status 1 (1)
799 RPM 7.83 A 36.4 kW The former provides access to all parameters. The latter
1.1 takes the user through a few parameters making it
0.000 possible to start operating the Adjustable frequency drive.
1.2
Regardless of the mode of programming, you can change
53.2% a parameter both in the main menu and quick menu
2
Auto Remote Ramping modes.

3 1.3 2.1.7 Quick Menu Key Functions

Pressing [Quick Menus] The list indicates the different

Status screen II areas contained in the Quick menu.
See the operating variables (1.1, 1.2, 1.3 and 2) shown in Select My Personal Menu to display the chosen personal
the screen below. parameters. These parameters are selected in 0-25 My
In the example, Speed, Motor current, Motor power and Personal Menu. Up to 20 different parameters can be
Frequency are selected as variables in the first and second. added in this menu.
130BP062.10

Status 1 (1)
207RPM 5.25A 24.4 kW
1.1

6.9Hz 1.3

1.2
Auto Remote Running

Status screen III

This state displays the event and action of the Smart Logic
Control. For further information, see section Smart Logic Select Quick set-up to go through a limited amount of
Control. parameters to get the motor running almost optimally. The
default setting for the other parameters considers the
desired control functions and the configuration of signal
inputs/outputs (control terminals).

Parameters are selected by using the arrow keys. The

parameters in the following table are accessible.

MG33MD22 - VLT® is a registered Danfoss trademark 2-5

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 How to Program FC 300 Programming Guide

Parameter Setting
2 2 0-01 Language
1-20 Motor Power [kW] [kW]
1-22 Motor Voltage [V]
1-23 Motor Frequency [Hz]
1-24 Motor Current [A]
1-25 Motor Nominal Speed [rpm]
5-12 Terminal 27 Digital Input [0] No function*
1-29 Automatic Motor [1] Enable complete AMA
Adaptation (AMA)
3-02 Minimum Reference [rpm]
3-03 Maximum Reference [rpm]
3-41 Ramp 1 Ramp up Time [sec]
3-42 Ramp 1 Ramp Down Time [sec]
3-13 Reference Site

* If terminal 27 is set to “no function”, no connection to

+24 V on terminal 27 is necessary.

Select Changes made to get information about:

• the last 10 changes. Use the [▲] [▼] navigation

keys to scroll between the last 10 changed
parameters.

• the changes made since default setting.

Select Loggings to get information about the display line
readouts. The information is shown as graphs.
Only display parameters selected in 0-20 Display Line 1.1
Small and 0-24 Display Line 3 Large can be viewed. It is
possible to store up to 120 samples in the memory for
later reference.

2-6 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 How to Program FC 300 Programming Guide

2.1.8 Initial Commissioning

2 2
The easiest way of carrying out the initial commissioning is by using the quick menu button and follow the quick set-up
procedure using LCP 102 (read table from left to right). The example applies to open-loop applications.

Press

Quick
Menu Q2 Quick Menu OK

0-01 Language OK Set language

1-20 Motor Power [kW] OK Set motor nameplate power

1-22 Motor Voltage OK Set nameplate voltage

1-23 Motor Frequency OK Set nameplate frequency

1-24 Motor Current OK Set nameplate current

1-25 Motor Nominal Speed OK Set Nameplate speed in RPM

If terminal default is Coast

inverse, it is possible to change
5-12 Terminal 27 Digital Input OK this setting to No function. No
connection to terminal 27 is
then needed for running AMA
Set desired AMA function.
1-29 Automatic Motor Adaptation
OK Enabling complete AMA is
(AMA)
recommended

Set the minimum speed of the

3-02 Minimum Reference OK
motor shaft

Set the maximum speed of the

3-03 Maximum Reference OK
motor shaft

Set the ramping-up time with

3-41 Ramp 1 Ramp up Time OK reference to synchronous
motor speed, ns.
Set the ramping-down time
3-42 Ramp 1 Ramp Down Time OK with reference to synchronous
motor speed, ns.

Set the site from where the

3-13 Reference Site OK
reference must work

MG33MD22 - VLT® is a registered Danfoss trademark 2-7

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 How to Program FC 300 Programming Guide

2.1.9 Main Menu Mode 2.1.11 Changing Data

2 2
Start main menu mode by pressing the [Main Menu] key. The procedure for changing data is the same whether you
The readout shown to the right appears on the display. select a parameter in the quick menu or the main menu
The middle and bottom sections on the display show a list mode. Press [OK] to change the selected parameter.
of parameter groups which can be chosen by toggling the The procedure for changing data depends on whether the
up and down buttons. selected parameter represents a numerical data value or a
text value.

130BP066.10
1107 RPM 3.84 A 1 (1)
Main Menu 2.1.12 Changing a Text Value
0 - ** Operation/Display
If the selected parameter is a text value, change the text
1 - ** Load/Motor
2 - ** Brakes
value with the [▲] [▼] navigation keys.
The up key increases the value, and the down key
3 - ** Reference / Ramps
decreases the value. Place the cursor on the value you
want to save and press [OK].

Each parameter has a name and number which remain the

130BP068.10
same regardless of the programming mode. In main menu 740RPM 10.64 A 1 [1]
Basic Settings 0-0*
mode, the parameters are divided into groups. The first
digit of the parameter number (from the left) indicates the 0 -01 Language

parameter group number.

[0] English
All parameters can be changed in the Main Menu.
However, depending on the choice of configuration
(1-00 Configuration Mode), some parameters can be
"missing". For example, open-loop hides all the PID 2.1.13 Changing a Group of Numeric Data
parameters, and other enabled options make more Values
parameter groups visible.
If the chosen parameter represents a numeric data value,
2.1.10 Parameter Selection change the chosen data value by means of the [◀] [▶]
navigation keys as well as the [▲] [▼] navigation keys. Use
In main menu mode, the parameters are divided into the [◀] [▶] navigation keys to move the cursor horizontally.
groups. Select a parameter group with the navigation keys.
The following parameter groups are accessible: 113 RPM 1.78 A 1(1)
130BP069.10

Load depen. setting 1- 6*

After selecting a par. group, choose a parameter by means 1 - 60 Low speed load
of the navigation keys.
compensation
The middle section on the display shows the parameter
100%
number and name as well as the selected parameter value.
130BP067.10

740RPM 10.64A 1 [1]

Basic Settings 0-0*
Use the [▲] [▼] navigation keys to change the data value.
0 -01 Language
The up key enlarges the data value, and the down key
reduces the data value. Place the cursor on the value you
[0] English want to save and press [OK].

2-8 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 How to Program FC 300 Programming Guide

15-30 Fault Log: Error Code to 15-32 Alarm Log: Time contain

130BP070.10
2 2
729RPM 6.21A 1(1)
Load depen. setting 1- 6* a fault log which can be read out. Choose a parameter,
press [OK], and use the [▲] [▼] navigation keys to scroll
1 - 60 Low speed load
compensation through the value log.
16 0%
Use 3-10 Preset Reference as another example:
Choose the parameter, press [OK], and use the [▲] [▼]
navigation keys to scroll through the indexed values. To
2.1.14 Infinitely Variable Change of change the parameter value, select the indexed value and
Numeric Data Value press [OK]. Change the value by using the [▲] [▼] keys.
Press [OK] to accept the new setting. Press [CANCEL] to
If the chosen parameter represents a numeric data value, abort. Press [Back] to leave the parameter.
select a digit with the [◀] [▶] navigation keys.
2.1.17 How to Program on the Numerical
Local Control Panel
130BP073.10

The following instructions are valid for the Numerical LCP

(LCP 101).
The control panel is divided into four functional groups:

1. Numerical display.
2. Menu keys and LEDs - changing parameters and
switching between display functions.
3. Navigation keys and LEDs (LEDs).
Change the selected digit infinitely variably with the [▲] 4. Operation keys and LEDs.
[▼] navigation keys.
Display line: Status messages displaying icons and numeric
The chosen digit is indicated by the cursor. Place the
value.
cursor on the digit you want to save and press [OK].

LEDs
130BP072.10

957RPM 11.58A 1 (1)

Start Adjustments 1-7*

• Green LED/On: Indicates if control section is on.
1-71 High starting torque time
• Yellow LED/Wrn.: Indicates a warning.
0. 4s
• Flashing red LED/Alarm: Indicates an alarm.

2.1.15 Value, Step-by-Step

Certain parameters can be changed step by step or

infinitely varying. This applies to 1-20 Motor Power [kW],
1-22 Motor Voltage and 1-23 Motor Frequency.
The parameters are changed both as a group of numeric
data values and as numeric data values infinitely varying.

2.1.16 Readout and Programming of

Indexed Parameters

Parameters are indexed when placed in a rolling stack.

MG33MD22 - VLT® is a registered Danfoss trademark 2-9

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 How to Program FC 300 Programming Guide

22.8
LCP keys

130BP077.10
2 2 [Menu] Select one of the following modes:
rpm

• Status Setup 1

• Quick Setup

• Main Menu

A 17

130BP078.10
130BA191.10
Setup 1

Main Menu/Quick Set-up is used for programming all

parameters or only the parameters in the Quick Menu (see
Setup also description of the LCP 102 earlier in this chapter).
1
The parameter values can be changed using the [▲] [▼]
keys when the value is flashing.
Select Main Menu by pressing the [Menu] key a number of
times.
Select the parameter group [xx-__] and press [OK]
Status Quick Main Select the parameter [__-xx] and press [OK]
2 Setup Menu
Menu If the parameter is an array parameter, select the array
number and press [OK]
Select the wanted data value and press [OK]
Parameters with functional choices display values such as
ck

[1], [2], etc. For a description of the different choices, see

Ba

the individual description of the parameters in the

Parameter Selection section

3 On OK
[Back] for stepping backwards
Arrow [▲] [▼] keys are used for navigating between
Warn.
commands and within parameters.
Alarm

Auto 130BP079.10
4 Hand Reset
Off
on on

Status Mode
P 2-03 Setup 1

Displays the status of the Adjustable frequency drive or

the motor.
If an alarm occurs, the NLCP automatically switches to Status Quick Main
Menu Setup Menu
status mode.
A number of alarms can be displayed.

NOTE!
Parameter copy is not possible with LCP 101 Numerical
Local Control Panel.

2-10 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 How to Program FC 300 Programming Guide

2.1.18 Local Control Keys 2.1.19 Initialization to Default Settings

2 2
Keys for local control are found at the bottom of the LCP. Initialize the Adjustable frequency drive to default settings
in two ways.

130BP046.10
Recommended initialization (via 14-22 Operation Mode)
Hand Auto
Off Reset
on on
1. Select 14-22 Operation Mode
2. Press [OK]
3. Select “Initialization”
[Hand on] enables control of the Adjustable frequency
4. Press [OK]
drive via the LCP. [Hand on] also starts the motor and it is
5. Cut off the line power supply and wait until the display
now possible to enter the motor speed data by means of
turns off.
the arrow keys. The key can be selected as Enable [1] og
6. Reconnect the line power supply - the Adjustable frequency
Disable [0] via 0-40 [Hand on] Key on LCP.
drive is now reset.
External stop signals activated by means of control signals
or a serial bus will override a 'start' command via the LCP.
The following control signals will still be active when 14-22 Operation Mode initializes all except:
[Hand on] is activated: 14-50 RFI Filter
8-30 Protocol

• [Hand on] - [Off] - [Auto on] 8-31 Address

8-32 FC Port Baud Rate
• Reset
8-35 Minimum Response Delay
• Coasting stop inverse 8-36 Max Response Delay
• Reversing 8-37 Max Inter-Char Delay
15-00 Operating Hours to 15-05 Over Volt's
• Set-up select lsb - Set-up select msb
15-20 Historic Log: Event to 15-22 Historic Log: Time
• Stop command from serial communication 15-30 Fault Log: Error Code to 15-32 Alarm Log: Time
• Quick stop

• DC brake Manual initialization

[Off] stops the connected motor. The key can be selected
as Enable [1] or Disable [0] via 0-41 [Off] Key on LCP. 1. Disconnect from the line power and wait until the
If no external stop function is selected and the [Off] key is display turns off.
inactive, the motor can be stopped by disconnecting the 2a. Press [Status] - [Main Menu] - [OK] at the same time
voltage. during power-up for LCP 102, Graphical Display
2b. Press [Menu] while powering up for LCP 101, Numerical
Display
[Auto on] enables the Adjustable frequency drive to be
controlled via the control terminals and/or serial communi- 3. Release the keys after 5 s.
cation. When a start signal is applied on the control 4. The Adjustable frequency drive is now programmed
terminals and/or the bus, the Adjustable frequency drive according to default settings.
will start. The key can be selected as Enable [1] or Disable
[0] via 0-42 [Auto on] Key on LCP. This procedure initializes all except:
15-00 Operating Hours
NOTE! 15-03 Power Up's
An active HAND-OFF-AUTO signal via the digital inputs has 15-04 Over Temp's
higher priority than the control keys [Hand on] [Auto on]. 15-05 Over Volt's

[Reset] is used for resetting the Adjustable frequency drive NOTE!

after an alarm (trip). It can be selected as Enable [1] or A manual initialization also resets serial communication, RFI
Disable [0] via 0-43 [Reset] Key on LCP. filter settings (14-50 RFI Filter) and fault log settings.

MG33MD22 - VLT® is a registered Danfoss trademark 2-11

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 How to Program FC 300 Programming Guide

2 2

2-12 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3 Parameter Descriptions

15-** Drive information parameters

3 3
3.1 Parameter Selection
16-** Readout parameters
Parameters for FC 300 are grouped into various parameter
groups for easy selection of the correct parameters for 17-** Encoder Option parameters
optimized operation of the Adjustable frequency drive.
0-** Operation and Display parameters 18-** Readout 2 parameters

• Basic settings, set-up handling 30-** Special Features

• Display and Local Control Panel parameters for
choosing readouts, setting up selections and 32-** MCO Basic Settings parameters
copying functions
1-** Load and Motor parameters includes all load and 33-** MCO Adv. Settings parameters
motor related parameters
34-** MCO Data Readouts
2-** Brake parameters
35-** Sensor Input Option parameters
• DC brake

• Dynamic brake (resistor brake)

• Mechanical brake

• Overvoltage Control
3-** References and ramping parameters includes DigiPot
function

4-** Limits / Warnings; setting of limits and warning

parameters

5-** Digital inputs and outputs includes relay controls

6-** Analog inputs and outputs

7-** Controls; Setting parameters for speed and process

controls

8-** Communication and option parameters for setting of

FC RS485 and FC USB port parameters.

9-** Profibus parameters

10-** DeviceNet and CAN Fieldbus parameters

12-** Ethernet parameters

13-** Smart Logic Control parameters

14-** Special function parameters

MG33MD22 - VLT® is a registered Danfoss trademark 3-1

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

0-01 Language
3.2 Parameters: 0-** Operation and Display Option: Function:
Polski Part of Language package 4
Parameters related to the fundamental functions of the
3 3 Adjustable frequency drive, function of the LCP buttons
Russian Part of Language package 3

and configuration of the LCP display. Thai Part of Language package 2

Bahasa Indonesia Part of Language package 2

3.2.1 0-0* Basic Settings
[52] Hrvatski

0-01 Language 0-02 Motor Speed Unit

Option: Function: Option: Function:
Defines the language to be used in the The display showing depends on settings in
display. The adjustable frequency drive 0-02 Motor Speed Unit and 0-03 Regional Settings. The
can be delivered with 4 different default setting of 0-02 Motor Speed Unit and
language packages. English and German 0-03 Regional Settings depends on which region of
are included in all packages. English the world the Adjustable frequency drive is supplied
cannot be erased or manipulated. to, but can be re-programmed as required.
[0] * English Part of Language packages 1 - 4
NOTE!
[1] Deutsch Part of Language packages 1 - 4 Changing the Motor Speed Unit will reset certain
[2] Francais Part of Language package 1 parameters to their initial value. It is
recommended to select the motor speed unit
[3] Dansk Part of Language package 1 first before modifying other parameters.
[4] Spanish Part of Language package 1
[0] RPM Selects display of motor speed variables and
[5] Italiano Part of Language package 1 parameters (i.e. references, feedbacks and limits) in
terms of motor speed (RPM).
Svenska Part of Language package 1
[1] * Hz Selects display of motor speed variables and
[7] Nederlands Part of Language package 1 parameters (i.e., references, feedbacks and limits) in
terms of output frequency to the motor (Hz).
[10] Chinese Part of Language package 2

Suomi Part of Language package 1 NOTE!

This parameter cannot be adjusted while the motor is
[22] English US Part of Language package 4 running.
Greek Part of Language package 4
0-03 Regional Settings
Bras.port Part of Language package 4
Option: Function:
Slovenian Part of Language package 3 [0] * Interna- Activates 1-20 Motor Power [kW] for setting
tional the motor power in kW and sets the default
Korean Part of Language package 2
value of 1-23 Motor Frequency to 50 Hz.
Japanese Part of Language package 2
[1] * US Activates 1-20 Motor Power [kW] for setting
Turkish Part of Language package 4 the motor power in HP and sets the default
value of 1-23 Motor Frequency to 60 Hz.
Trad.Chinese Part of Language package 2

Bulgarian Part of Language package 3 NOTE!

Srpski Part of Language package 3 This parameter cannot be adjusted while the motor is
running.
Romanian Part of Language package 3

Magyar Part of Language package 3

Czech Part of Language package 3

3-2 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

0-04 Operating State at Power-up (Hand) 0-10 Active Set-up

Option: Function: Option: Function:
Selects the operating mode upon Select the set-up to control the Adjustable
reconnection of the Adjustable frequency
drive to AC line voltage after power-down in
[0] Factory
frequency drive functions.

Cannot be changed. It contains the Danfoss

3 3
hand (local) operation mode.
setup data set, and can be used as a data source
[0] Resume Restarts the Adjustable frequency drive when returning the other set-ups to a
maintaining the same local reference and the known state.
same start/stop settings (applied by [HAND
[1] * Set-up 1 Set-up 1 [1] to Set-up 4 [4] are the four
ON/OFF]) as before the Adjustable frequency
separate parameter set-ups within which all
drive was powered down.
parameters can be programmed.
[1] * Forced stop, Restarts the Adjustable frequency drive with
[2] Set-up 2
ref=old a saved local reference, after AC line voltage
[3] Set-up 3
reappears and after pressing [HAND ON].
[4] Set-up 4
[2] Forced stop, Resets the local reference to 0 upon [9] Multi Set-up Remote selection of set-ups using digital
ref=0 restarting the Adjustable frequency drive. inputs and the serial communication port.
This set-up uses the settings from 0-12 This
Set-up Linked to. Stop the Adjustable
3.2.2 0-1* Set-up Operations
frequency drive before making changes to
open-loop and closed-loop functions
Define and control the individual parameter set-ups.
The Adjustable frequency drive has four parameter set-ups Use 0-51 Set-up Copy to copy a set-up to one or all other
that can be programmed independently of each other. This set-ups. Stop the Adjustable frequency drive before
makes the Adjustable frequency drive very flexible and switching between set-ups where parameters marked ‘not
able to solve advanced control functionality problems, changeable during operation’ have different values. To
often saving the cost of external control equipment. For avoid conflicting settings of the same parameter within
example, these can be used to program the Adjustable two different set-ups, link the set-ups together using
frequency drive to operate according to one control 0-12 This Set-up Linked to. Parameters which are ‘not
scheme in one set-up (e.g., motor 1 for horizontal changeable during operation’ are marked FALSE in the
movement) and another control scheme in another set-up parameter lists in the section Parameter Lists.
(e.g., motor 2 for vertical movement). Alternatively they
can be used by an OEM machine builder to identically 0-11 Edit Set-up
program all their factory fitted adjustable frequency drives Option: Function:
for different machine types within a range to have the Select the set-up to be edited (i.e.,
same parameters and then during production/commis- programmed) during operation: either the
sioning simply select a specific set-up depending on which active set-up or one of the inactive set-ups.
machine the Adjustable frequency drive is installed on.
[0] Factory setup Cannot be edited, but it is useful as a data
The active set-up (i.e., the set-up in which the Adjustable
source for returning the other set-ups to a
frequency drive is currently operating) can be selected in
known state.
0-10 Active Set-up and is displayed in the LCP. Using Multi
set-up, it is possible to switch between set-ups with the [1] * Set-up 1 Set-up 1 [1] to Set-up 4 [4] can be edited
Adjustable frequency drive running or stopped, via digital freely during operation, independently of
input or serial communication commands. If it is necessary the active set-up.
to change set-ups while running, ensure 0-12 This Set-up [2] Set-up 2
Linked to is programmed as required. Using 0-11 Edit Set-
[3] Set-up 3
up, it is possible to edit parameters within any of the set-
[4] Set-up 4
ups whilst continuing the Adjustable frequency drive
[9] Active Set-up Can also be edited during operation. Edit
operation in its Active Set-up which can be a different set-
the chosen set-up from a range of sources:
up to that being edited. Using 0-51 Set-up Copy, it is
LCP, FC RS-485, FC USB or up to five serial
possible to copy parameter settings between the set-ups
communication bus sites.
to enable quicker commissioning if similar parameter
settings are required in different set-ups.

MG33MD22 - VLT® is a registered Danfoss trademark 3-3

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

0-12 This Set-up Linked to

Option: Function:

130BP075.10
3 3

OR

2. While still in Set-up 1, copy Set-up 1 to Set-

up 2. Then set 0-12 This Set-up Linked to to Set-
up 2 [2]. This will start the linking process.

130BP076.10
After the link is complete, 0-13 Readout: Linked
Set-ups will read {1,2} to indicate that all ‘not
changeable during operation’ parameters are
now the same in Set-up 1 and Set-up 2. If there
are changes to a "not changeable during
0-12 This Set-up Linked to operation" parameter, e.g., 1-30 Stator Resistance
Option: Function: (Rs) in Set-up 2, they will also be changed
automatically in Set-up 1. A switch between
To enable conflict-free changes from one set-up
Set-up 1 and Set-up 2 during operation is now
to another during operation, link set-ups
possible.
containing parameters that are not changeable
during operation. The link will ensure the [0] * Not linked
proper synchronization of the ‘not changeable [1] Set-up 1
during operation’ parameter values when [2] Set-up 2
moving from one set-up to another during [3] Set-up 3
operation. ‘Not changeable during operation’ [4] Set-up 4
parameters can be identified by the label FALSE
in the parameter lists in the section Parameter
Lists.

0-12 This Set-up Linked to is used by Multi set-

up in 0-10 Active Set-up. Multi set-up is used to
move from one set-up to another during
operation (i.e., while the motor is running).
Example:
Use Multi set-up to shift from Set-up 1 to Set-
up 2 while the motor is running. Program in
Set-up 1 first, then ensure that Set-up 1 and
Set-up 2 are synchronized (or ‘linked’). Synchro-
nization can be performed in two ways:
1. Change the edit set-up to Set-up 2 [2] in
0-11 Edit Set-up and set 0-12 This Set-up Linked
to to Set-up 1 [1]. This will start the linking
(synchronizing) process.

3-4 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

0-13 Readout: Linked Set-ups 0-20 Display Line 1.1 Small

Array [5] Option: Function:
Range: Function: Select a variable for display in
0* [0 - 255 ] View a list of all the set-ups linked by means of
0-12 This Set-up Linked to. The parameter has one [0] * None
line 1, left position.

No display value selected.

3 3
index for each parameter set-up. The parameter
[9] Performance Monitor
value displayed for each index represents which
[15] Readout: actual setup
set-ups are linked to that parameter set-up.
[37] Display Text 1
Index LCP value [38] Display Text 2
0 {0} [39] Display Text 3
1 {1,2} [748] PCD Feed Forward
2 {1,2} [953] Profibus Warning
3 {3} Word
4 {4} [1005] Readout Transmit
Error Counter
Table 3.2 Example: Set-up 1 and Set-up 2 are [1006] Readout Receive
linked Error Counter
[1007] Readout Bus Off
0-14 Readout: Edit Set-ups / Channel Counter
[1013] Warning Parameter
Range: Function:
[1230] Warning Parameter
0* [-2147483648 - View the setting of 0-11 Edit Set-up for each
[1472] Legacy Alarm Word
2147483647 ] of the four different communication
[1473] Legacy Warning
channels. When the number is displayed in
Word
hex, as it is in the LCP, each number
[1474] Leg. Ext. Status Word
represents one channel.
Numbers 1-4 represent a set-up number; ‘F’ [1501] Running Hours
means factory setting; and ‘A’ means active [1502] kWh Counter
set-up. The channels are, from right to left: [1600] Control Word Present control word
LCP , FC-bus, USB, HPFB1-5. [1601] Reference [Unit] Total reference (sum of digital/
Example: The number AAAAAA21h means analog/preset/bus/freeze ref./
that the FC bus selected Set-up 2 in catch up and slow-down) in
0-11 Edit Set-up, the LCP selected Set-up 1 selected unit.
and all others used the active set-up.
[1602] Reference % Total reference (sum of digital/
analog/preset/bus/freeze ref./
0-15 Readout: actual setup
catch up and slow-down) in
Range: Function: percent.
0* [0 - 255 ] Makes it possible to read out the active set-up,
[1603] Status Word Present status word.
also when multi set-up is selected in par. 0-10.
[1605] Main Actual Value Actual value as a percentage.
[%]
3.2.3 0-2* LCP Display [1609] Custom Readout
[1610] Power [kW] Actual power consumed by the
Define the variables displayed in the Graphical Local motor in kW.
Control Panel.
[1611] Power [hp] Actual power consumed by the
motor in HP.
NOTE!
Please refer to 0-37 Display Text 1, 0-38 Display Text 2 and [1612] Motor Voltage Voltage supplied to the motor.
0-39 Display Text 3 for information on how to write display [1613] Frequency Motor frequency, i.e., the output
texts. frequency from the Adjustable
frequency drive in Hz

MG33MD22 - VLT® is a registered Danfoss trademark 3-5

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

0-20 Display Line 1.1 Small 0-20 Display Line 1.1 Small
Option: Function: Option: Function:
[1614] Motor Current Phase current of the motor [1651] Pulse Reference Frequency in Hz connected to

3 3 [1615] Frequency [%]

measured as effective value.

Motor frequency, i.e., the output

the digital inputs (18, 19 or 32,
33).

frequency from the Adjustable [1652] Feedback [Unit] Reference value from
frequency drive in percent. programmed digital input(s).

[1616] Torque [Nm] Actual motor torque in Nm [1653] Digi Pot Reference

[1617] * Speed [RPM] Speed in RPM (revolutions per [1657] Feedback [RPM]
minute), i.e., the motor shaft [1660] Digital Input Signal states form the 6 digital
speed in closed-loop. terminals (18, 19, 27, 29, 32 and
33). There are 16 bits in total,
[1618] Motor Thermal Thermal load on the motor,
but only six of them are used.
calculated by the ETR function.
Input 18 corresponds to the
[1619] KTY sensor leftmost of the used bits. Signal
temperature low = 0; Signal high = 1.
[1620] Motor Angle [1661] Terminal 53 Switch Setting of input terminal 54.
[1621] Torque [%] High Res. Setting Current = 0; Voltage = 1.
[1622] Torque [%] Present motor load as a
[1662] Analog Input 53 Actual value at input 53 either
percentage of the rated motor
as a reference or protection
torque.
value.
[1625] Torque [Nm] High
[1663] Terminal 54 Switch Setting of input terminal 54.
[1630] DC Link Voltage Intermediate circuit voltage in
Setting Current = 0; Voltage = 1.
the Adjustable frequency drive.
[1664] Analog Input 54 Actual value at input 54 either
[1632] Brake Energy /s Present braking energy
as reference or protection value.
transferred to an external brake
resistor. [1665] Analog Output 42 Actual value at output 42 in mA.
Stated as an instantaneous [mA] Use 6-50 Terminal 42 Output to
value. select the value to be shown.

[1633] Brake Energy /2 min Braking energy transferred to an [1666] Digital Output [bin] Binary value of all digital
external brake resistor. The mean outputs.
power is calculated continuously [1667] Freq. Input #29 [Hz] Actual value of the frequency
for the most recent 120 seconds. applied at terminal 29 as an
[1634] Heatsink Temp. Present heatsink temperature of impulse input.
the Adjustable frequency drive. [1668] Freq. Input #33 [Hz] Actual value of the frequency
The cut-out limit is 203°±9°F [95° applied at terminal 33 as an
±5°C]; cutting back in occurs at impulse input.
158°F ±9°F [70°C ± 5°C].
[1669] Pulse Output #27 Actual value of impulses applied
[1635] Inverter Thermal Percentage load of the inverters. [Hz] to terminal 27 in digital output
[1636] Inv. Nom. Current Nominal current of the mode.
Adjustable frequency drive. [1670] Pulse Output #29 Actual value of impulses applied
[1637] Inv. Max. Current Maximum current of the [Hz] to terminal 29 in digital output
Adjustable frequency drive. mode.

[1638] SL Controller State State of the event executed by [1671] Relay Output [bin]
the control. [1672] Counter A Application dependent (e.g., SLC
Control)
[1639] Control Card Temp. Temperature of the control card.
[1673] Counter B Application dependent (e.g., SLC
[1650] External Reference Sum of the external reference as
Control)
a percentage, i.e., the sum of
analog/pulse/bus. [1674] Prec. Stop Counter Display the actual counter value.

3-6 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

0-20 Display Line 1.1 Small 0-20 Display Line 1.1 Small
Option: Function: Option: Function:
[1675] Analog In X30/11 Actual value at input X30/11 [3019] Wobble Delta Freq.
either as reference or protection
value. [3110]
Scaled
Bypass Status Word 3 3
[1676] Analog In X30/12 Actual value at input X30/12 [3111] Bypass Running
either as reference or protection Hours
value. [3401] PCD 1 Write to MCO
[3402] PCD 2 Write to MCO
[1677] Analog Out X30/8 Actual value at output X30/8 in
[3403] PCD 3 Write to MCO
[mA] mA. Use 6-60 Terminal X30/8
[3404] PCD 4 Write to MCO
Output to select the value to be
[3405] PCD 5 Write to MCO
shown.
[3406] PCD 6 Write to MCO
[1678] Analog Out X45/1
[3407] PCD 7 Write to MCO
[mA]
[3408] PCD 8 Write to MCO
[1679] Analog Out X45/3
[3409] PCD 9 Write to MCO
[mA]
[3410] PCD 10 Write to MCO
[1680] Fieldbus CTW 1 Control word (CTW) received
[3421] PCD 1 Read from
from the bus master.
MCO
[1682] Fieldbus REF 1 Main reference value sent with [3422] PCD 2 Read from
control word from the bus MCO
master. [3423] PCD 3 Read from
[1684] Comm. Option STW Extended serial communication MCO
option status word. [3424] PCD 4 Read from
MCO
[1685] FC Port CTW 1 Control word (CTW) received
[3425] PCD 5 Read from
from the bus master.
MCO
[1686] FC Port REF 1 Status word (STW) sent to the [3426] PCD 6 Read from
bus master. MCO
[1690] Alarm Word One or more alarms in a Hex [3427] PCD 7 Read from
code. MCO
[3428] PCD 8 Read from
[1691] Alarm Word 2 One or more alarms in a Hex
MCO
code.
[3429] PCD 9 Read from
[1692] Warning Word One or more warnings in a Hex MCO
code. [3430] PCD 10 Read from
[1693] Warning Word 2 One or more warnings in a Hex MCO
code. [3440] Digital Inputs
[3441] Digital Outputs
[1694] Ext. Status Word One or more status conditions in
[3450] Actual Position
a Hex code.
[3451] Commanded Position
[1836] Analog Input X48/2
[3452] Actual Master
[mA]
Position
[1837] Temp. Input X48/4
[3453] Slave Index Position
[1838] Temp. Input X48/7
[3454] Master Index Position
[1839] Temp. Input X48/10
[3455] Curve Position
[1860] Digital Input 2
[3456] Track Error
[1890] Process PID Error
[3457] Synchronizing Error
[1891] Process PID Output
[3458] Actual Velocity
[1892] Process PID Clamped
[3459] Actual Master
Output
Velocity
[1893] Process PID Gain
[3460] Synchronizing Status
Scaled Output

MG33MD22 - VLT® is a registered Danfoss trademark 3-7

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

0-20 Display Line 1.1 Small 0-25 My Personal Menu

Option: Function: Range: Function:
[3461] Axis Status Application [0 - Define up to 50 parameters to appear in

3 3 [3462]
[3464]
Program Status
MCO 302 Status
dependent* 9999 ] the Q1 Personal Menu, accessible via
the [Quick Menu] key on the LCP. The
[3465] MCO 302 Control parameters will be displayed in the Q1
[3470] MCO Alarm Word 1 Personal menu in the order they are
[3471] MCO Alarm Word 2 programmed into this array parameter.
[4285] Active Safe Func. Delete parameters by setting the value
[4286] Safe Option Info to ‘0000’.
[9913] Idle time For example, this can be used to
[9914] Paramdb requests in provide quick, simple access to just one
queue or up to 50 parameters which require
changing on a regular basis (e.g., for
[9917] tCon1 time
plant maintenance reasons) or by an
[9918] tCon2 time
OEM to enable simple commissioning of
[9919] Time Optimize
their equipment.
Measure
[9920] HS Temp. (PC1)
[9921] HS Temp. (PC2) 3.2.4 0-3* LCP Custom Readout
[9922] HS Temp. (PC3)
[9923] HS Temp. (PC4) It is possible to customize the display elements for various
[9924] HS Temp. (PC5) purposes: *Custom Readout. Value proportional to speed
[9925] HS Temp. (PC6) (linear, squared or cubed depending on unit selected in
[9926] HS Temp. (PC7) 0-30 Custom Readout Unit) *Display Text. Text string stored
[9927] HS Temp. (PC8) in a parameter.

0-21 Display Line 1.2 Small Custom Readout

Option: Function: The calculated value to be displayed is based on settings
[0] * None Select a variable for display in line 1, middle in 0-30 Custom Readout Unit, 0-31 Custom Readout Min
position. The options are the same as listed for Value (linear only), 0-32 Custom Readout Max Value,
0-20 Display Line 1.1 Small. 4-13 Motor Speed High Limit [RPM], 4-14 Motor Speed High
Limit [Hz] and actual speed.
0-22 Display Line 1.3 Small
Option: Function:
[30120] * Mains Current Select a variable for display in line 1,
[A] right position. The options are the
same as listed for 0-20 Display Line 1.1
Small.

0-23 Display Line 2 Large

Option: Function:
[30100] * Output Current Select a variable for display in line 2.
[A] The options are the same as listed for
0-20 Display Line 1.1 Small.

0-24 Display Line 3 Large

Select a variable for display in line 3. The relation will depend on the type of unit selected in
Option: Function: 0-30 Custom Readout Unit:
[30121] * Mains Frequency The options are the same as those
listed in 0-20 Display Line 1.1 Small.

3-8 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

Unit Type Speed Relation 0-30 Unit for User-defined Readout

Dimensionless Option: Function:
Speed
[123] gal/h
Flow, volume
Flow, mass Linear
[124] CFM
[125] ft³/s 3 3
Velocity
[126] ft³/min
Length
[127] ft³/h
Temperature
[130] lb/s
Pressure Quadratic
[131] lb/min
Power Cubic
[132] lb/h
[140] ft/s
0-30 Unit for User-defined Readout [141] ft/min
Option: Function: [145] ft
It is possible to program a value to be shown in [160] °F
the display of the LCP. The value will have a [170] psi
linear, squared or cubed relation to speed. This [171] lb/in²
relation will depend on the unit selected (see [172] in WG
table above). The actual calculated value can be [173] ft WG
read in 16-09 Custom Readout, and/or shown in [180] HP
the display by selecting Custom Readout [16-09]
in 0-20 Display Line 1.1 Small to 0-24 Display Line 3 0-31 Min Value of User-defined Readout
Large. Range: Function:
[0] * None 0.00 Custom- [Application This parameter sets the min.
[1] % ReadoutUnit* dependant] value of the custom defined
[5] PPM readout (occurs at zero speed).
Only possible to set different
[10] 1/min
from 0 is when selecting a
[11] rpm
linear unit in 0-30 Unit for User-
[12] Pulse/s
defined Readout. For quadratic
[20] l/s
and cubic units, the minimum
[21] l/min
value will be 0.
[22] l/h
0.00 Custom- [Application This parameter sets the min.
[23] m³/s
ReadoutUnit* dependant] value of the custom defined
[24] m³/min
readout (occurs at zero speed).
[25] m³/h
Only possible to set different
[30] kg/s
from 0 is when selecting a
[31] kg/min
linear unit in 0-30 Unit for User-
[32] kg/h
defined Readout. For quadratic
[33] t/min and cubic units, the minimum
[34] t/h value will be 0.
[40] m/s
[41] m/min 0-32 Custom Readout Max Value
[45] m Range: Function:
[60] °C
100.00 Custom- [ par. 0-31 - This parameter sets the max
[70] mbar ReadoutUnit* 999999.99 value to be shown when
[71] bar CustomRea- the speed of the motor has
[72] Pa doutUnit] reached the set value for
[73] kPa 4-13 Motor Speed High Limit
[74] m WG [RPM] or 4-14 Motor Speed
[80] kW High Limit [Hz] (depends on
[120] GPM setting in 0-02 Motor Speed
[121] gal/s Unit).
[122] gal/min

MG33MD22 - VLT® is a registered Danfoss trademark 3-9

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

0-37 Display Text 1 0-41 [Off] Key on LCP

Range: Function: Option: Function:
0* [0 - 0 ] Enter a text which can be viewed in the graphical [0] * Disabled Avoids accidental stop of the Adjustable

3 3 display by selecting Display Text 1 [37] in

0-20 Display Line 1.1 Small, 0-21 Display Line 1.2
[1] * Enabled
frequency drive.

Small, 0-22 Display Line 1.3 Small, 0-23 Display Line 2

[2] Password Avoids unauthorized stop. If 0-41 [Off] Key on LCP
Large or 0-24 Display Line 3 Large.
is included in the Quick Menu, then define the
password in 0-65 Quick Menu Password.
0-38 Display Text 2
Range: Function: 0-42 [Auto on] Key on LCP
0* [0 - 0 ] Enter a text which can be viewed in the graphical Option: Function:
display by selecting Display Text 2 [38] in
[0] * Disabled Avoid accidental start of the Adjustable
0-20 Display Line 1.1 Small, 0-21 Display Line 1.2
frequency drive in auto mode.
Small, 0-22 Display Line 1.3 Small, 0-23 Display Line 2
Large or 0-24 Display Line 3 Large. [1] * Enabled
[2] Password Avoids unauthorized start in auto mode. If
0-39 Display Text 3 0-42 [Auto on] Key on LCP is included in the
Range: Function: Quick Menu, then define the password in
0-65 Quick Menu Password.
0* [0 - 0 ] Enter a text which can be viewed in the graphical
display by selecting Display Text 3 [39] in
0-43 [Reset] Key on LCP
0-20 Display Line 1.1 Small, 0-21 Display Line 1.2
Small, 0-22 Display Line 1.3 Small, 0-23 Display Line 2 Option: Function:
Large or 0-24 Display Line 3 Large. [0] * Disabled No effect when [Reset] is pressed. Avoids
accidental alarm reset.

[1] * Enabled
3.2.5 0-4* LCP Keypad
[2] Password Avoids unauthorized resetting. If
0-43 [Reset] Key on LCP is included in the
Enable, disable and password protect individual keys on
Quick Menu, then define the password in
the LCP.
0-65 Quick Menu Password.
0-40 [Hand on] Key on LCP
[7] Enabled Resets the Adjustable frequency drive
Option: Function: without OFF without setting it in Off mode.
[0] * Disabled No effect when [Hand on] is pressed.
[8] Password Resets the Adjustable frequency drive
Select [0] Disabled to avoid accidental
without OFF without setting it in Off mode. A password
start of the Adjustable frequency drive in
is required when pressing [Reset] (see [2]).
Hand on mode.

[1] * Enabled The LCP switches to Hand on mode

directly when [Hand on] is pressed. 3.2.6 0-5* Copy/Save
[2] Password After pressing [Hand on], a password is
Copy parameter settings between set-ups and to/from the
required. If 0-40 [Hand on] Key on LCP is
LCP.
included in My Personal Menu, define the
password in 0-65 Quick Menu Password. 0-50 LCP Copy
Otherwise, define the password in Option: Function:
0-60 Main Menu Password.
[0] * No copy
[3] Hand Off/On When [Hand on] is pressed once, the LCP [1] All to LCP Copies all parameters in all set-ups
switches to Off mode. When pressed from the Adjustable frequency drive
again, the LCP switches to Hand on mode. memory to the LCP memory.

[4] Hand Off/On Same as [3] but a password is required [2] All from LCP Copies all parameters in all set-ups
w. Passw. (see [2]). from the LCP memory to the
Adjustable frequency drive memory.
[9] Enabled, ref =
0

3-10 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

0-50 LCP Copy 0-61 Access to Main Menu w/o Password

Option: Function: Option: Function:
[3] Size indep. from Copy only the parameters that are [0] * Full access Disables password defined in 0-60 Main
LCP independent of the motor size. The
latter selection can be used to
[1]
Menu Password.

LCP: Read only Prevent unauthorized editing of main

3 3
program several adjustable frequency
menu parameters.
drives with the same function without
disturbing motor data. [2] LCP: No access Prevent unauthorized viewing and editing
of main menu parameters.
[4] File from MCO to
LCP [3] Bus: Read only Read-only functions for parameters on
[5] File from LCP to Serial communication bus and/or FC
MCO standard bus.
[6] Data from DYN to [4] Bus: No access No access to parameters is allowed via
LCP Serial communication bus and/or FC
[7] Data from LCP to standard bus.
DYN
[5] All: Read only Read-only function for parameters on LCP,
NOTE! Serial communication bus or FC standard
bus.
This parameter cannot be adjusted while the motor is
running. [6] All: No access No access from LCP, Serial communication
bus or FC standard bus is allowed.
0-51 Set-up Copy
If Full access [0] is selected then 0-60 Main Menu Password,
Option: Function: 0-65 Personal Menu Password and 0-66 Access to Personal
[0] * No copy No function Menu w/o Password will be ignored.
[1] Copy to set- Copies all parameters in the present NOTE!
up 1 Programming Set-up (defined in
More complex password protection is available for OEMs
0-11 Programming Set-up) to Set-up 1.
upon request.
[2] Copy to set- Copies all parameters in the present
up 2 Programming Set-up (defined in 0-65 Quick Menu Password
0-11 Programming Set-up) to Set-up 2.
Range: Function:
[3] Copy to set- Copies all parameters in the present 200* [-9999 - Define the password for access to the quick
up 3 Programming Set-up (defined in 9999 ] menu via the [Quick Menu] key. If
0-11 Programming Set-up) to Set-up 3. 0-66 Access to Quick Menu w/o Password is
[4] Copy to set- Copies all parameters in the present set to Full access [0], this parameter will be
up 4 Programming Set-up (defined in ignored.
0-11 Programming Set-up) to Set-up 4.
0-66 Access to Quick Menu w/o Password
[9] Copy to all Copies the parameters in the present set-up
over to each of the set-ups 1 to 4. Option: Function:
[0] * Full access Disables the password defined in
0-65 Quick Menu Password.
3.2.7 0-6* Password
[1] LCP: Read only Prevents unauthorized editing of quick
menu parameters.
0-60 Main Menu Password
[3] Bus: Read only Read only functions for quick menu
Range: Function:
parameters on Serial communication bus
100 * [0 - 999 ] Define the password for access to the main
and/ or FC standard bus.
menu via the [Main Menu] key. If 0-61 Access
to Main Menu w/o Password is set to Full [5] All: Read only read only function for quick menu
access [0], this parameter will be ignored. parameters on LCP, Serial communication
bus or FC standard bus.

If 0-61 Access to Main Menu w/o Password is set to Full

access [0], then this parameter will be ignored.

MG33MD22 - VLT® is a registered Danfoss trademark 3-11

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

0-67 Bus Password Access

Range: Function:
0* [0 - 9999 ] Writing to this parameter enables users to

3 3 unlock the adjustable frequency drive from

bus/MCT 10 Set-up Software.

3-12 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.3 Parameters: 1-** Load and Motor 1-01 Motor Control Principle
Option: Function:
3.3.1 1-0* General Settings
Select which motor control principle to

Define whether the Adjustable frequency drive operates in

speed mode or torque mode; and whether the internal PID [0] * U/f
employ.

special motor mode, for parallel connected

3 3
control should be active or not. motors in special motor applications. When
U/f is selected the characteristic of the
1-00 Configuration Mode control principle can be edited in 1-55 U/f
Option: Function: Characteristic - U and 1-56 U/f Characteristic -
Select the application control principle to be F.
used when a remote reference (i.e., via [1] VVC+ Voltage vector control principle suitable for
analog input or serial communication bus) is most applications. The main benefit of
active. A remote reference can only be active
VVCplus operation is that it uses a robust
when 3-13 Reference Site is set to [0] or [1].
motor model.
[0] * Speed open Enables speed control (without feedback
[2] Flux Flux Vector control without encoder
loop signal from motor) with automatic slip
sensorless feedback, for simple installation and
compensation for almost constant speed at
robustness against sudden load changes. FC
varying loads.
302 only.
Compensations are active but can be
disabled in the Load/Motor parameter group [3] Flux w/ very high accuracy speed and torque
1-0*. motor feedb control, suitable for the most demanding
applications. FC 302 only.
[1] Speed Enables Speed closed-loop control with
closed loop feedback. Obtain full holding torque at 0 The best shaft performance is normally achieved using
RPM. either of the two flux vector control modes Flux sensorless
For increased speed accuracy, provide a [2] and Flux with encoder feedback [3].
feedback signal and set the speed PID
control.
NOTE!
[2] Torque Enables torque closed-loop control with This parameter cannot be adjusted while the motor is
feedback. Only possible with “Flux with running.
motor feedback” option, 1-01 Motor Control
Principle. FC 302 only.
NOTE!
[3] Process Enables the use of process control in the An overview of possible combinations of the settings in
Adjustable frequency drive. The process 1-00 Configuration Mode and 1-01 Motor Control Principle
control parameters are set in parameter can be found in 4.1.1 Conversion.
groups 7-2* and 7-3*.

[4] Torque open Enables the use of torque open-loop in VVC+ 1-02 Flux Motor Feedback Source
loop mode (1-01 Motor Control Principle). The
Option: Function:
torque PID parameters are set in parameter
Select the interface at which to receive
group 7-1*.
feedback from the motor.
[5] Wobble Enables the wobble functionality in
[0] Motor feedb. P1-02
30-00 Wobble Mode to 30-19 Wobble Delta
[1] * 24V encoder A and B channel encoder, which can
Freq. Scaled.
only be connected to the digital input
[6] Surface Enables the surface winder control specific terminals 32/33. Terminals 32/33 must
Winder parameters in parameter group 7-2* and be programmed to No operation.
7-3*.
[2] MCB 102 Encoder module option which can be
[7] Extended Specific parameters in parameter group 7-2* configured in parameter group 17-1*
PID Speed to 7-5*. FC 302 only.
OL
[3] MCB 103 Optional resolver interface module
[8] Extended Specific parameters in parameter group 7-2*
which can be configured in parameter
PID Speed to 7-5*.
group 17-5*
CL

MG33MD22 - VLT® is a registered Danfoss trademark 3-13

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

1-02 Flux Motor Feedback Source NOTE!

Option: Function: This parameter cannot be adjusted while the motor is
[4] MCO Encoder 1 Encoder interface 1 of the optional running.

3 3 X56 programmable motion controller MCO

305. 1-04 Overload Mode
[5] MCO Encoder 2 Encoder interface 2 of the optional Option: Function:
X55 programmable motion controller MCO [0] * High torque Allows up to 160% overtorque.
305.
[1] Normal torque For oversized motor - allows up to 110%
[6] Analog input 53 overtorque.
[7] Analog input 54
[8] Frequency input 29 NOTE!
[9] Frequency input 33 This parameter cannot be adjusted while the motor is
running.
NOTE!
This parameter cannot be adjusted while the motor is
1-05 Local Mode Configuration
running.
Option: Function:
Select which application configuration
1-03 Torque Characteristics
mode (1-00 Configuration Mode), i.e., the
Option: Function: application control principle, to use when a
Select the torque characteristic required. Local (LCP) Reference is active. A local
VT and AEO are both energy saving operations. reference can be active only when
[0] Constant Motor shaft output provides constant torque 3-13 Reference Site is set to [0] or [2]. By
* torque under variable speed control. default, the local reference is active in hand
mode only.
[1] Variable Motor shaft output provides variable torque
torque under variable speed control. Set the variable [0] Speed open
torque level in 14-40 VT Level. loop
[1] Speed closed
[2] Auto Automatically optimizes energy consumption by
loop
Energy minimizing magnetization and frequency via
[2] * As mode par
Optim. 14-41 AEO Minimum Magnetisation and
1-00
14-42 Minimum AEO Frequency.

[5] Constant The function provides a constant power in the 1-06 Clockwise Direction
Power field weakening area. This parameter defines the term “Clockwise” corresponding to
The torque shape of motor mode is used as a the LCP direction arrow. Used for easy change of direction of
limit in generator mode. This is done to limit the shaft rotation without swapping motor wires. (Valid from SW
power in generatoric mode that otherwise version 5.84)
becomes considerable larger than in motor Option: Function:
mode, due to the high DC link voltage available
[0] * Normal Motor shaft will turn in clockwise
in generator mode.
direction when the Adjustable
Pshaft W = ωmech rad / s × T Nm frequency drive is connected U ->
This relationship with the constant power is U; V -> V, and W -> W to motor.
illustrated in the following graph: [1] Inverse Motor shaft will turn in counter
T[Nm] P[W] clockwise direction when the
130BB655.10

Tnom
Adjustable frequency drive is
Pnom P connected U -> U; V -> V, and W -
> W to motor.

T
ωnom 2ωnom ω [rad/S]
NOTE!
This parameter cannot be changed while the motor is
running.

3-14 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.3.2 1-1* Motor Selection 1-21 Motor Power [HP]

Range: Function:
NOTE! unit. This parameter is visible in
This parameter group cannot be adjusted while the motor
is running.
LCP if 0-03 Regional Settings is
US [1] 3 3
1-10 Motor Construction 1-22 Motor Voltage
Option: Function: Range: Function:
Select the motor construction type. Application [Application Enter the nominal motor
dependent* dependant] voltage according to the
[0] * Asynchron For asynchronous motors.
motor nameplate data. The
[1] PM, non salient For permanent magnet (PM) motors. default value corresponds to
SPM Note that PM motors are divided into the nominal rated output of
two groups, with either surface mounted the unit.
(non-salient) or interior (salient) magnets.
1-23 Motor Frequency
Motor construction can either be asynchronous or Range: Function:
permanent magnet (PM) motor.
Application [20 - Min - Max motor frequency: 20–1000Hz.
dependent* 1000 Select the motor frequency value from
3.3.3 1-2* Motor Data Hz] the motor nameplate data. If a value
different from 50Hz or 60Hz is selected, it
Parameter group 1-2* comprises input data from the is necessary to adapt the load
nameplate on the connected motor. independent settings in 1-50 Motor
Magnetisation at Zero Speed to
NOTE! 1-53 Model Shift Frequency. For 87Hz
Changing the value of these parameters affects the setting operation with 230/400V motors, set the
of other parameters. nameplate data for 230V/50Hz. Adapt
4-13 Motor Speed High Limit [RPM] and
3-03 Maximum Reference to the 87Hz
1-20 Motor Power [kW]
application.
Range: Function:
Application [Application Enter the nominal motor power in 1-24 Motor Current
dependent* dependant] kW according to the motor Range: Function:
nameplate data. The default value
Application [Application Enter the nominal motor
corresponds to the nominal rated
dependent* dependant] current value from the motor
output of the unit.
nameplate data. The data are
This parameter cannot be
used for calculating torque,
adjusted while the motor is
motor protection, etc.
running. This parameter is visible
in LCP if 0-03 Regional Settings is
1-25 Motor Nominal Speed
International [0].
Range: Function:
NOTE! Application [10 - 60000 Enter the nominal motor speed
Four sizes down, one size up dependent* RPM] value from the motor
from nominal unit rating. nameplate data. The data are
used for calculating motor
compensations.
1-21 Motor Power [HP]
Range: Function: 1-26 Motor Cont. Rated Torque
Application [Application Enter the nominal motor power Range: Function:
dependent* dependant] in HP according to the motor
Application [0.1 - Enter the value from the motor
nameplate data. The default
dependent* 10000.0 nameplate data. The default value
value corresponds to the
Nm] corresponds to the nominal rated
nominal rated output of the

MG33MD22 - VLT® is a registered Danfoss trademark 3-15

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

1-26 Motor Cont. Rated Torque 1-29 Automatic Motor Adaptation (AMA)
Range: Function: Option: Function:
output. This parameter is available [2] Enable Performs a reduced AMA of the stator

3 3 when 1-10 Motor Construction is set

to PM, non salient SPM [1], i.e., the
reduced
AMA
resistance Rs in the system only.

parameter is valid for PM and non-

Note:
salient SPM motors only.

Application [0.1 - Enter the value from the motor • For the best adaptation of the Adjustable
frequency drive,, run AMA on a cold motor.
dependent* 10000.0 nameplate data. The default value
Nm] corresponds to the nominal rated • AMA cannot be performed while the motor is
output. This parameter is available running.
when 1-10 Motor Construction is set
• AMA cannot be performed on permanent magnet
to PM, non salient SPM [1], i.e., the motors.
parameter is valid for PM and non-
salient SPM motors only.
NOTE!
1-29 Automatic Motor Adaptation (AMA) It is important to set motor parameter group 1-2*
correctly, since these form part of the AMA algorithm. An
Option: Function:
AMA must be performed to achieve optimum dynamic
The AMA function optimizes dynamic motor motor performance. It may take up to 10 min, depending
performance by automatically optimizing the on the power rating of the motor.
advanced motor parameters (1-30 Stator
Resistance (Rs) to 1-35 Main Reactance (Xh)) at
motor standstill.
NOTE!
Avoid generating external torque during AMA.
Activate the AMA function by pressing [Hand
on] after selecting [1] or [2]. See also the
section Automatic Motor Adaptation in the NOTE!
Design Guide. After a normal sequence, the If one of the settings in parameter group 1-2* is changed,
display will read: "Press [OK] to finish AMA". 1-30 Stator Resistance (Rs) to 1-39 Motor Poles, the
After pressing the [OK] key, the Adjustable advanced motor parameters, will return to default setting.
frequency drive is ready for operation.

This parameter cannot be adjusted while the NOTE!

motor is running. AMA will work problem-free on 1 motor size down,
typically work on 2 motor sizes down, rarely work on 3
[0] Off
sizes down and never work on 4 sizes down. Please keep
*
in mind that the accuracy of the measured motor data will
[1] Enable Performs AMA of the stator resistance RS, the
be poorer when you operate on motors smaller than
complete rotor resistance Rr, the stator leakage reactance
nominal VLT size.
AMA X1, the rotor leakage reactance X2 and the
main reactance Xh. Do not select this option if
an LC filter is used between the Adjustable
3.3.4 1-3* Addl. Motor Data
frequency drive and the motor.
FC 301: The Complete AMA does not include Parameters for advanced motor data. The motor data in
Xh measurement for FC 301. Instead, the Xh 1-30 Stator Resistance (Rs) to 1-39 Motor Poles must match
value is determined from the motor database. the relevant motor in order to run the motor optimally.
RS is the best adjustment method (see 1-3* The default settings are figures based on common motor
Adv. Motor Data). parameter values from standard motors. If the motor
T4/T5 E and F frames, T7 D, E and F frames will parameters are not set correctly, a malfunction of the
only run a reduced AMA when the complete Adjustable frequency drive system may occur. If the motor
AMA is selected. It is recommended to obtain data is not known, running an AMA (Automatic Motor
the Advanced Motor Data from the motor Adaptation) is recommended. See the Automatic Motor
manufacturer to enter into 1-31 Rotor Resistance Adaptation section in the Design Guide. The AMA
(Rr) through 1-36 Iron Loss Resistance (Rfe) for sequence will adjust all motor parameters except the
best performance.

3-16 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

moment of inertia of the rotor and the iron loss resistance 1-33 Stator Leakage Reactance (X1)
(1-36 Iron Loss Resistance (Rfe)). Range: Function:
Parameter groups 1-3* and 1-4* cannot be adjusted while
Application [Application Set the stator leakage reactance of
the motor is running.

P 1-34
dependent* dependant] the motor using one of these
methods: 3 3

130BA065.12
P 1-30 P 1-33
I1 Rs X1δ X'2δ 1. Run an AMA on a cold
motor. The Adjustable
frequency drive will
measure the value from
U1 the motor.
P 1-36 P 1-35 P 1-31
RFe Xh R'r
2. Enter the X1 value
manually. Obtain the
value from the motor
supplier.
Figure 3.1 Motor equivalent diagram for an asynchronous
3. Use the X1 default setting.
motor
The Adjustable frequency
drive establishes the
setting on the basis of the
NOTE! motor nameplate data.
A simple check of the X1 + Xh sum value is to divide the
line to line motor voltage by the sqrt(3) and divide this 1-34 Rotor Leakage Reactance (X2)
value by the motor no load current. [VL-L/sqrt(3)]/INL = X1
Range: Function:
+ Xh. These values are important to properly magnetize
Application dependent* [Application dependant]
the motor. For high pole motors it is highly recommended
to perform this check. 1-35 Main Reactance (Xh)
Range: Function:
1-30 Stator Resistance (Rs) Application [Application Set the main reactance of the
Range: Function: dependent* dependant] motor using one of these methods:
Application dependent* [Application dependant] 1. Run an AMA on a cold
motor. The Adjustable
1-31 Rotor Resistance (Rr)
frequency drive will
Range: Function: measure the value from
Application [Application Fine-tuning Rr will improve shaft the motor.
dependent* dependant] performance. Set the rotor
2. Enter the Xh value
resistance value using one of these
manually. Obtain the value
methods:
from the motor supplier.
1. Run an AMA on a cold
3. Use the Xh default setting.
motor. The Adjustable
The Adjustable frequency
frequency drive will
drive establishes the
measure the value from
setting on the basis of the
the motor. All compen-
motor nameplate data.
sations are reset to 100%.

2. Enter the Rr value 1-36 Iron Loss Resistance (Rfe)

manually. Obtain the value
Range: Function:
from the motor supplier.
Application dependent* [Application dependant]
3. Use the Rr default setting.
The Adjustable frequency 1-37 d-axis Inductance (Ld)
drive establishes the Range: Function:
setting on the basis of the Application dependent* [Application dependant]
motor nameplate data.

MG33MD22 - VLT® is a registered Danfoss trademark 3-17

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

1-39 Motor Poles 3.3.5 1-5* Load Indep. Setting

Range: Function:
Application [2 - 100 ] Enter the number of motor 1-50 Motor Magnetisation at Zero Speed

3 3 dependent*

Application
poles.

[2 - 100 ] Value 2 - 100 poles

Range:
100 %* [0 - 300 %]
Function:

dependent*
NOTE!
Poles ~nn@ 50Hz ~nn@60Hz 1-50 Motor Magnetisation at Zero Speed will not have effect
2 2700–2880 3250–3460
when 1-10 Motor Construction = [1] PM, non-salient SPM.
4 1350–1450 1625–1730
6 700–960 840–1153 1-51 Min Speed Normal Magnetising [RPM]
Range: Function:
The table shows the number of poles for normal speed Size [10 - 300 Set the required speed for normal
ranges of various motor types. Define motors designed for related* RPM] magnetizing current. If the speed is set
other frequencies separately. The motor pole value is lower than the motor slip speed,
always an even number, because it refers to the total 1-50 Motor Magnetisation at Zero Speed
number of poles, not pairs of poles. The Adjustable and 1-51 Min Speed Normal Magnetising
frequency drive creates the initial setting of 1-39 Motor [RPM] are of no significance.
Poles based on 1-23 Motor Frequency and 1-25 Motor Use this parameter along with
Nominal Speed. 1-50 Motor Magnetisation at Zero Speed.
See .
1-40 Back EMF at 1000 RPM
Range: Function: NOTE!
Application [Application Set the nominal back EMF for 1-51 Min Speed Normal Magnetising [RPM] will not have
dependent* dependant] the motor when running at 1000 effect when 1-10 Motor Construction = [1] PM, non-salient
RPM. This parameter is only SPM.
active when 1-10 Motor
Construction is set to PM motor
1-52 Min Speed Normal Magnetising [Hz]
[1] (Permanent Magnet Motor).
FC 302 only. Range: Function:
Application dependent* [Application dependant]
NOTE!
When using PM motors, it is 1-53 Model Shift Frequency
recommended to use brake Range: Function:
resistors. Application Flux Model shift
dependent* [Application Enter the frequency value for shift
dependant] between two models for
1-41 Motor Angle Offset
determining motor speed. Choose
Range: Function: the value based on settings in
0* [-32768 - Enter the correct offset angle between the PM 1-00 Configuration Mode and
32767 ] motor and the index position (single-turn) of the 1-01 Motor Control Principle. There
attached encoder or resolver. The value range of are two options: shift between Flux
0–32768 corresponds to 0–2 * pi (radians). To model 1 and Flux model 2; or shift
obtain the offset angle value: After Adjustable between Variable Current mode and
frequency drive start-up, apply DC hold and Flux model 2.FC 302 only.
enter the value of 16-20 Motor Angle into this This parameter cannot be adjusted
parameter. while the motor is running.
This parameter is only active when 1-10 Motor
Flux model 1 – Flux model 2
Construction is set to PM, non-salient SPM [1]
This model is used when
(Permanent Magnet Motor).
1-00 Configuration Mode is set to
Speed closed-loop [1] or Torque [2]
and 1-01 Motor Control Principle is
set to Flux w/motor feedback [3].

3-18 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

1-53 Model Shift Frequency 1-54 Voltage reduction in fieldweakening

Range: Function: Range: Function:
With this parameter it is possible to motor in fieldweakening, giving more voltage
make an adjustment of the shifting
point where FC 302 changes
available for torque. Be aware that a value that
is too high may cause stalling problems at high 3 3
between Flux model 1 and Flux speed.
model 2, which is useful in some
sensitive speed and torque control 1-55 U/f Characteristic - U
applications. Range: Function:
fN,M x 0.1 fN,M x 0.125 Application [0.0 - Enter the voltage at each

130BA146.11
dependent* 1000.0 V] frequency point to manually form a
Flux model 1 Flux model 2 U/f characteristic matching the
motor.
P 1-53 fout The frequency points are defined
Figure 3.2 1-00 Configuration in 1-56 U/f Characteristic - F.
Mode = [1] Speed closed-loop or This parameter is an array
[2] Torque and 1-01 Motor Control parameter [0-5] and is only
Principle = [3] Flux w/motor accessible when 1-01 Motor Control
feedback Principle is set to U/f [0].

1-56 U/f Characteristic - F

Variable Current - Flux model - Range: Function:
Sensorless Application [Application Enter the frequency points to
This model is used when dependent* dependant] manually form a U/f-charac-
1-00 Configuration Mode is set to teristic matching the motor.
Speed open-loop [0] and 1-01 Motor The voltage at each point is
Control Principle is set to Flux defined in 1-55 U/f Characteristic
sensorless [2]. - U.
In speed open-loop in flux mode, This parameter is an array
the speed is determined by the parameter [0-5] and is only
current measurement. accessible when 1-01 Motor
Below fnorm x 0.1, the Adjustable Control Principle is set to U/f [0].
frequency drive runs on a variable
current model. Above fnorm x 0.125
the Adjustable frequency drive runs
on a flux model.

fN,M x 0.1 fN,M x 0.125

130BA147.10

Variable
current Flux model 2
model

P 1-53 fout

Figure 3.3 1-00 Configuration

Mode = [0] Speed open-loop,
1-01 Motor Control Principle = [2]
Flux sensorless
1-58 Flystart Test Pulses Current
Range: Function:
30 %* [0 - 200 Control the percentage of the magnetizing
1-54 Voltage reduction in fieldweakening %] current for the pulses used to detect the
Range: Function: motor direction. Reducing this value will
0 V* [0 - 100 The value of this parameter will reduce the reduce the generated torque. 100% means
V] maximal voltage available for the flux of the nominal motor current. The parameter is

MG33MD22 - VLT® is a registered Danfoss trademark 3-19

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

1-58 Flystart Test Pulses Current 1-62 Slip Compensation

Range: Function: Range: Function:
active when 1-73 Flying Start is enabled. This value of nM,N. Slip compensation is

3 3 parameter is only available in VVCplus. calculated automatically, i.e., on the

basis of the rated motor speed nM,N.
1-59 Flystart Test Pulses Frequency This function is not active when
Range: Function: 1-00 Configuration Mode is set to Speed
closed-loop [1] or Torque [2] Torque
200 %* [0 - 500 Control the percentage of the frequency for
control with speed feedback or when
%] the pulses used to detect the motor
1-01 Motor Control Principle is set to U/f
direction. Increasing this value will reduce
[0] special motor mode.
the generated torque. 100% means 2 times
the slip frequency. The parameter is active
1-63 Slip Compensation Time Constant
when 1-73 Flying Start is enabled. This
parameter is only available in VVCplus. Range: Function:
Size related* [0.05 - 5.00 Enter the slip compensation reaction
s] speed. A high value results in slow
3.3.6 1-6* Load Depend. Setting reaction, and a low value results in
quick reaction. If low-frequency
1-60 Low Speed Load Compensation resonance problems arise, use a
Range: Function: longer time setting.
100 %* [0 - 300 %]
NOTE!
Motor size Change-over 1-63 Slip Compensation Time Constant will not have effect
0.34–10 hp [0.25–7.5 kW] < 10Hz when 1-10 Motor Construction = [1] PM, non-salient SPM.

1-64 Resonance Dampening

Range: Function:
100 %* [0 - 500 %]

NOTE!
1-64 Resonance Dampening will not have effect when
1-10 Motor Construction = [1] PM, non-salient SPM.

1-65 Resonance Dampening Time Constant

Range: Function:
5 ms* [5 - 50 ms] Set 1-64 Resonance Dampening and
1-65 Resonance Dampening Time Constant to
help eliminate high-frequency resonance
problems. Enter the time constant that
provides the best dampening.
1-61 High Speed Load Compensation
Range: Function:
NOTE!
1-65 Resonance Dampening Time Constant will not have
100 %* [0 - 300 %]
effect when 1-10 Motor Construction = [1] PM, non-salient
SPM.
Motor size Change-over
0.34–10 hp [0.25–7.5 kW] > 10Hz
1-66 Min. Current at Low Speed

1-62 Slip Compensation Range: Function:

100 %* [Application dependant]
Range: Function:
Application [-500 - Enter the % value for slip compensation
dependent* 500 %] to compensate for tolerances in the

3-20 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

1-67 Load Type 1-72 Start Function

Option: Function: Option: Function:
[0] * Passive load For conveyers, fan and pump applications. [1] DC Brake/ Energizes motor with a DC braking current

[1] Active load For hoisting applications, used in slip

compensation at low speed. When Active Load
delay time (2-01 DC Brake Current) during the start delay
time. 3 3
[1] is selected, set 1-66 Min. Current at Low [2] Coast/delay Motor coasted during the start delay time
Speed to a level which corresponds to * time (inverter off).
maximum torque.
[3] Start speed Only possible with VVCplus.
cw Connect the function described in 1-74 Start
FC 302 only.
Speed [RPM] and 1-76 Start Current in the
1-68 Minimum Inertia start delay time.
Range: Function: Regardless of the value applied by the
Application [Application Needed for average inertia reference signal, the output speed applies
dependent* dependant] calculation. Enter the minimum the setting of the start speed in 1-74 Start
moment of inertia of the Speed [RPM] or 1-75 Start Speed [Hz] and the
mechanical system. 1-68 Minimum output current corresponds to the setting of
Inertia and 1-69 Maximum Inertia the start current in 1-76 Start Current. This
are used for pre-adjustment of function is typically used in hoisting
the Proportional Gain in the applications without counterweight, and
speed control, see 30-83 Speed PID especially in applications with a cone motor
Proportional Gain. where the start is clockwise, followed by
FC 302 only. rotation in the reference direction.

[4] Horizontal Only possible with VVCplus.

This parameter cannot be adjusted while motor is running. operation For obtaining the function described in
1-69 Maximum Inertia 1-74 Start Speed [RPM] and 1-76 Start Current
during the start delay time. The motor
Range: Function:
rotates in the reference direction. If the
Application [Application Active in flux open-loop only.
reference signal equals zero (0), 1-74 Start
dependent* dependant] Used to compute the
Speed [RPM] is ignored and the output speed
acceleration torque at low
equals zero (0). The output current
speed. Used in the torque limit
corresponds to the setting of the start
controller.
current in 1-76 Start Current.
FC 302 only.
[5] VVC+/Flux for the function described in 1-74 Start Speed
This parameter cannot be adjusted while motor is running. clockwise [RPM] only. The start current is calculated
automatically. This function uses the start
speed in the start delay time only. Regardless
3.3.7 1-7* Start Adjustments
of the value set by the reference signal, the
output speed equals the setting of the start
1-71 Start Delay
speed in 1-74 Start Speed [RPM]. Start speed/
Range: Function: current clockwise [3] and VVCplus/Flux clockwise
0.0 s* [0.0 - 25.5 s] This parameter refers to the start function [5] are typically used in hoisting applications.
selected in 1-72 Start Function. Start speed/current in reference direction [4] is
Enter the time delay required before particularly used in applications with counter-
commencing acceleration. weight and horizontal movement.

[6] Hoist Mech. For utilizing mechanical brake control

1-72 Start Function
Brake Rel functions, 2-24 Stop Delay to 2-28 Gain Boost
Option: Function: Factor. This parameter is only active when
Select the start function during start delay. 1-01 Motor Control Principle is set to [3] Flux
This parameter is linked to 1-71 Start Delay. w/ motor feedback (FC 302 only).
[0] DC Hold/ Energizes motor with a DC holding current [7] VVC+/Flux
delay time (2-00 DC Hold Current) during the start delay counter-cw
time.

MG33MD22 - VLT® is a registered Danfoss trademark 3-21

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

1-73 Flying Start 1-76 Start Current

Option: Function: Range: Function:
This function makes it possible to catch disengage the rotor. To obtain this

3 3 a motor that is spinning freely due to a

line drop-out.
boost, set the required current in
1-76 Start Current. Set 1-74 Start Speed
[RPM]. Set 1-72 Start Function to [3] or
[0] * Disabled No function
[4], and set a start delay time in
[1] Enabled Enables the Adjustable frequency drive 1-71 Start Delay.
to “catch” and control a spinning motor.
This parameter can be used for hoist
When 1-73 Flying Start is enabled,
applications (cone rotor).
1-71 Start Delay and 1-72 Start Function
have no function.

[2] Enabled Always 3.3.8 1-8* Stop Adjustments

[3] Enabled Ref. Dir.
[4] Enab. Always 1-80 Function at Stop
Ref. Dir. Option: Function:

NOTE! Select the Adjustable frequency drive

function after a stop command or after the
This parameter cannot be adjusted while motor is running.
speed is ramped down to the settings in
1-81 Min Speed for Function at Stop [RPM].
NOTE! [0] Coast Leaves motor in free mode. The motor is
This function is not recommended for hoisting
* disconnected from the Adjustable frequency
applications.
drive.
For power levels above 75 hp [55 kW], flux mode must be
used to achieve the best performance. [1] DC hold Energizes motor with a DC holding current
(see 2-00 DC Hold Current).

NOTE! [2] Motor check Checks if a motor has been connected.

To obtain the best flying start performance the advanced [3] Pre- Builds up a magnetic field while the motor
motor data, parameters 1-30 through 1-35, must be magnetizing is stopped. This allows the motor to
correct. produce torque quickly at subsequent start
commands (asynchronous motors only). This
1-74 Start Speed [RPM] pre-magnetizing function does not help the
Range: Function: very first start command. Two different
solutions are available to pre-magnetize the
Application [0 - 600 RPM] This parameter can be used
machine for the first start command:
dependent* for hoist applications (cone
rotor). 1. Start the Adjustable frequency
drive with a 0RPM reference and
1-75 Start Speed [Hz] wait 2 to 4 rotor time constants
(see below) before increasing the
Range: Function:
speed reference.
Application [Application This parameter can be used for
dependent* dependant] hoist applications (cone rotor). 2a. Set 1-71 Start Delay to the
Set a motor start speed. After the desired pre-mag time (2 to 4 rotor
start signal, the output speed time constants - see below).
leaps to set value. Set the start 2b. Set 1-72 to either [0] DC-hold
function in 1-72 Start Function to or [1] DC Brake.
[3], [4] or [5], and set a start
Set the DC hold or DC brake
delay time in 1-71 Start Delay.
current magnitude (2-00 or 2-01) to
be equal to I_pre-mag = Unom /
1-76 Start Current
(1.73 x Xh)
Range: Function:
Sample rotor time constants =
0.00 [Application Some motors, e.g., cone rotor motors,
(Xh+X2) / (6.3*Freq_nom*Rr)
A* dependant] need extra current/starting speed to

3-22 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

1-80 Function at Stop 1-83 Precise Stop Function

Option: Function: Option: Function:
1.35 hp [1 kW] = 0.2 seconds the maximum speed (set in 4-19 Max Output
13.5 hp [10 kW] = 0.5 seconds
135 hp [100 kW] = 1.7 seconds
Frequency).
The delay is calculated on the basis of the 3 3
1,350 hp [1,000 kW] = 2.5 seconds reference speed of the Adjustable frequency
drive and not on the basis of the actual speed.
[4] DC Voltage When the motor is stopped, the P1-55 [0]
Please therefore make sure that the Adjustable
U0 parameter defines the voltage at 0 Hz.
frequency drive has ramped up before you
[5] Coast at low When the reference is below 1-81 Min Speed activate the speed compensated stop.
reference for Function at Stop [RPM], the motor is
[4] Com cnt Same as [3] but after each precise stop, the
disconnected from the Adjustable frequency
stop w/rst number of pulses counted during ramp-down to
drive.
0 rpm is reset.

1-81 Min Speed for Function at Stop [RPM] [5] Comp cnt Same as [3] but the number of pulses counted
Range: Function: stop w/o during ramp-down to 0 rpm is deducted from
r the counter value entered in 1-84 Precise Stop
Size related* [0 - 600 RPM] Set the speed at which to activate
Counter Value.
1-80 Function at Stop.
This reset function can, for example, be used to
compensate for the extra distance done during
1-82 Min Speed for Function at Stop [Hz]
ramping down and to reduce the impact of
Range: Function:
gradual wear on mechanical parts.
Size related* [ 0.0 - 20.0 Hz]
The precise stop functions are advantageous in
1-83 Precise Stop Function
applications where high precision is required.
Option: Function: If you use a standard stop command the accuracy is
[0] Precise Only optimal when the operational speed of, for determined by the internal task time. That is not the case
* ramp example, the conveyor belt is constant. This is when you use the precise stop function; it eliminates the
stop an open-loop control. Achieves high repetitive task time dependence and increases the accuracy substan-
precision at the stopping point. tially.
The Adjustable frequency drive tolerance is normally given
[1] Cnt stop Counts the number of pulses, typically from an
by its task time. However, by using its special precise stop
with reset encoder and generates a stop signal after a pre-
function the tolerance is independent of the task time
programmed number of pulses - 1-84 Precise
because the stop signal immediately interrupts the
Stop Counter Value - has been received at T29 or
execution of the Adjustable frequency drive program. The
T33 [30].
precise stop function gives a highly reproducible delay
This is a direct feedback with one-way closed-
from the stop signal is given until the ramping down
loop control.
starts. A test must be done to find this delay as it is a sum
The counter function is activated (starts timing)
of sensor, PLC, Adjustable frequency drive and mechanical
at the edge of the start signal (when it changes
parts.
from stop to start). After each precise stop, the
To ensure optimum accuracy, there should be at least 10
number of pulses counted during ramp-down to
cycles during ramping down, see 3-42 Ramp 1 Ramp Down
0 rpm is reset.
Time, 3-52 Ramp 2 Ramp down Time, 3-62 Ramp 3 Ramp
[2] Cnt stop Same as [1] but the number of pulses counted down Time and 3-72 Ramp 4 Ramp Down Time .
w/o reset during ramp-down to 0 rpm is deducted from The precise stop function is set up here and enabled from
the counter value entered in 1-84 Precise Stop DI T29 or T33.
Counter Value.
This reset function can, for example, be used to
compensate for the extra distance done during
NOTE!
ramping down and to reduce the impact of
This parameter cannot be adjusted while the motor is
gradual wear on mechanical parts.
running.

[3] Speed Stops at precisely the same point, regardless of

comp the present speed, the stop signal is delayed
stop internally when the present speed is lower than

MG33MD22 - VLT® is a registered Danfoss trademark 3-23

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

1-84 Precise Stop Counter Value 1-90 Motor Thermal Protection

Range: Function: Option: Function:
100000* [0 - 999999999 ] Enter the counter value to be used [0] * No Continuously overloaded motor, when no

3 3 in the integrated precise stop

function, 1-83 Precise Stop Function.
protection warning or trip of the Adjustable frequency
drive is required.
The maximum permissible frequency
[1] Thermistor Activates a warning when the connected
at terminal 29 or 33 is 110kHz.
warning thermistor or KTY sensor in the motor reacts
Not used for selection [0] and [3] in in the event of motor overtemperature.
1-83 Precise Stop Function
[2] Thermistor Stops (trips) Adjustable frequency drive when
trip connected thermistor or KTY sensor in the
motor reacts in the event of motor overtem-
1-85 Precise Stop Speed Compensation Delay
perature.
Range: Function:
The thermistor cut-out value must be > 3
10 ms* [0 - 100 Enter the delay time for sensors, PLCs, etc.
kΩ.
ms] for use in 1-83 Precise Stop Function. In
speed compensated stop mode, the delay Integrate a thermistor (PTC sensor) in the
time at different frequencies has a major motor for winding protection.
influence on the stop function. [3] ETR warning Calculates the load when set-up 1 is active
Not used for selection [0], [1] and [2] in 1 and activates a warning on the display when
1-83 Precise Stop Function the motor is overloaded. Program a warning
signal via one of the digital outputs.

[4] ETR trip 1 Calculates the load when set-up 1 is active

3.3.9 1-9* Motor Temperature and stops (trips) Adjustable frequency drive
when the motor is overloaded. Program a
warning signal via one of the digital outputs.
1-90 Motor Thermal Protection
The signal appears in the event of a warning
Option: Function:
and if the Adjustable frequency drive trips
Thermal motor protection can be (thermal warning).
implemented using a range of techniques:
[5] ETR warning
• Via a PTC sensor in the motor 2
windings connected to one of the
[6] ETR trip 2
analog or digital inputs
[7] ETR warning
(1-93 Thermistor Source). See
3
3.3.10.1 PTC Thermistor Connection.
[8] ETR trip 3
• Via a KTY sensor in the motor [9] ETR warning
winding connected to an analog 4
input (1-96 KTY Thermistor Resource). [10] ETR trip 4
See 3.3.10.2 KTY Sensor Connection.
[20] ATEX ETR Activates the thermal monitoring function for
• Via calculation (ETR = Electronic Ex-e motors for ATEX. Enables 1-94 ATEX ETR
Thermal Relay) of the thermal load, cur.lim. speed reduction, 1-98 ATEX ETR
based on the actual load and time. interpol. points freq. and 1-99 ATEX ETR
The calculated thermal load is interpol points current.
compared with the rated motor
[21] Advanced
current IM,N and the rated motor
ETR
frequency fM,N. See 3.3.10.3 ETR and
3.3.10.4 ATEX ETR. NOTE!
• Via a mechanical thermal switch If [20] is selected, follow the instructions exactly as
(Klixon type). See 3.3.10.5 Klixon. described in the dedicated chapter in the VLT
AutomationDrive design guide and the instructions given
For the North American market: The ETR
by the motor manufacturer.
functions provide class 20 motor overload
protection in accordance with NEC.

3-24 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

NOTE!
If [20] is selected, 4-18 Current Limit must be set to 150%.

3.3.10.1 PTC Thermistor Connection

3 3

Input Supply Voltage Threshold

Digital/analog Cut-out Values
Digital 10 V < 800Ω - > 2.7 kΩ
Analog 10 V < 3.0 kΩ - > 3.0 kΩ

NOTE!
Ensure that the chosen supply voltage follows the specifi-
cation of the thermistor element utilized.

3.3.10.2 KTY Sensor Connection

Figure 3.4 PTC profile (FC 302 only)

KTY sensors are used especially in permanent magnet
servo motors (PM motors) for dynamic adjusting of motor
Using a digital input and 10 V as power supply: parameters as stator resistance (1-30 Stator Resistance (Rs))
Example: The Adjustable frequency drive trips when the for PM motors and also rotor resistance (1-31 Rotor
motor temperature is too high. Resistance (Rr)) for asynchronous motors, depending on
Parameter set-up: winding temperature. The calculation is:
Set 1-90 Motor Thermal Protection to Thermistor Trip [2]
Set 1-93 Thermistor Source to Digital Input [6] Rs = Rs20° C x (1 + αcu x ΔT ) Ω where αcu = 0.00393

KTY sensors can be used for motor protecting (1-97 KTY

+10V

130BA152.10

Threshold level).
39 42 50 53 54 55
FC 302 can handle three types of KTY sensors, defined in
1-95 KTY Sensor Type. The actual sensor temperature can be
OFF
read out from 16-19 KTY sensor temperature.
12 13 18 19 27 29 32 33 20 37

ON
PTC / Thermistor <800 Ω >2.7 kΩ R

Using an analog input and 10 V as power supply:

Example: The Adjustable frequency drive trips when the
motor temperature is too high.
Parameter set-up:
Set 1-90 Motor Thermal Protection to Thermistor Trip [2]
Set 1-93 Thermistor Source to Analog Input 54 [2]

MG33MD22 - VLT® is a registered Danfoss trademark 3-25

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

4500 3.3.10.4 ATEX ETR

130BB917.10
4000
The B option MCB 112 PTC Thermistor option offers ATEX
approved monitoring of motor temperature. Alternatively,
3 3
3500

an external ATEX approved PTC protection device can be

3000
used.

NOTE!
Resistance [Ohm]

2500

2000
Only ATEX Ex-e approved motors may be used for this
function. See motor nameplate, approval certificate, data
1500 sheet or contact motor supplier.

1000
When controlling an Ex-e motor with “Increased Safety”, it
500 is important to ensure certain limitations. The parameters
that must be programmed are presented in the following
0
-25 0 25 50 75 100 125 150
application example.
Temperature [°C]

KTY type 1 KTY type 2 KTY type 3 Parameters

Function Setting
Figure 3.5 KTY type selection 1-90 Motor Thermal Protection [20] ATEX ETR
1-94 ATEX ETR cur.lim. speed 20%
reduction
KTY Sensor 1: KTY 84-1 with 1kΩ at 212°F [100°C] 1-98 ATEX ETR interpol. points
KTY Sensor 2: KTY 81-1, KTY 82-1 with 1kΩ at 77°F [25°C] freq.
Motor nameplate
KTY Sensor 3: KTY 81-2, KTY 82-2 with 2kΩ at 77°F [25°C] 1-99 ATEX ETR interpol points

NOTE! current
1-23 Motor Frequency Enter the same value as for
If the temperature of the motor is utilized through a
4-19 Max Output Frequency
thermistor or KTY sensor, the PELV is not complied with in
4-19 Max Output Frequency Motor nameplate, possibly
the event of short circuits between motor windings and
reduced for long motor cables,
sensor. In order to comply with PELV, the sensor must be
sinus filter or reduced supply
extra isolated.
voltage
4-18 Current Limit Forced to 150% by 1-90 [20]
3.3.10.3 ETR 5-15 Terminal 33 Digital [80] PTC Card 1
Input
The calculations estimate the need for a lower load at
5-19 Terminal 37 Safe Stop [4] PTC 1 Alarm
lower speed due to less cooling from the fan incorporated
14-01 Switching Frequency Check that the default value fulfils
in the motor.
the requirement for Motor
t [s]
175ZA052.11

nameplate. If not, use the sine-

2000 wave filter.

1000
14-26 Trip Delay at Inverter 0
600
Fault
500
400

CAUTION
300
200

100 fOUT = 1 x f M,N It is mandatory to compare the minimum switching

60
fOUT = 2 x f M,N frequency requirement stated by the motor manufacturer
50
40
fOUT = 0.2 x f M,N to the minimum switching frequency of the Adjustable
30 frequency drive, the default value in 14-01 Switching
20
Frequency. If the Adjustable frequency drive does not meet
10 IM this requirement, a sine-wave filter must be used.
1.0 1.2 1.4 1.6 1.8 2.0 IMN

Figure 3.6 ETR profile

More information about ATEX ETR Thermal Monitoring can
be found in the Application Note MN.33.GX.YY.

3-26 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.3.10.5 Klixon NOTE!

This parameter cannot be adjusted while the motor is
The Klixon type thermal circuit breaker uses a KLIXON® running.
metal dish. At a predetermined overload, the heat caused
by the current through the disc causes a trip. NOTE! 3 3
Using a digital input and 24 V as power supply: Digital input should be set to [0] PNP - Active at 24V in
Example: The Adjustable frequency drive trips when the 5-00 Digital I/O Mode.
motor temperature is too high
Parameter set-up: 1-94 ATEX ETR cur.lim. speed reduction
Set 1-90 Motor Thermal Protection to Thermistor Trip [2]
FC 302 only.
Set 1-93 Thermistor Source to Digital Input [6]
Only visible if 1-90 Motor Thermal Protection is set to [20].

130BA151.11
+24V

GND

Range: Function:
OFF
B
A

12 13 18 19 27 29 32 33 20 37 0.0 %* [0.0 - 100.0 %]

The reaction for operating in Ex-e current limit must be

configured.
0%: The Adjustable frequency drive does not change
ON
PTC / Thermistor anything besides issuing warning 163 ATEX ETR
<6.6 k Ω >10.8 k Ω R
cur.lim.warning.
>0%: The Adjustable frequency drive issuing warning 163
1-91 Motor External Fan and reduces motor speed following ramp 2 (parameter
Option: Function: group 3-5*).
[0] * No No external fan is required, i.e., the motor is derated
at low speed. Example:
Actual reference = 50 RPM
[1] Yes Applies an external motor fan (external ventilation), so
1-94 ATEX ETR cur.lim. speed reduction = 20%
that no derating of the motor is required at low
Resulting reference = 40 RPM
speed. The upper curve in graph above (fout = 1 x
fM,N) is followed if the motor current is lower than 1-95 KTY Sensor Type
nominal motor current (see 1-24 Motor Current). If the Option: Function:
motor current exceeds nominal current, the operation Select the used type of KTY sensor. FC 302
time still decreases as if no fan were installed. only.

[0] * KTY Sensor 1 1kΩ at 212° F [100° C]

1-93 Thermistor Source
Option: Function: [1] KTY Sensor 2 1kΩ at 77 °F [25 °C]
Select the input to which the thermistor [2] KTY Sensor 3 2kΩ at 77 °F [25 °C]
(PTC sensor) should be connected. An
analog input option [1] or [2] cannot be 1-96 KTY Thermistor Resource
selected if the analog input is already in Option: Function:
use as a reference source (selected in
Selecting analog input terminal 54 to be used
3-15 Reference 1 Source, 3-16 Reference 2
as KTY sensor input. Terminal 54 cannot be
Source or 3-17 Reference 3 Source ).
selected as KTY source if otherwise used as
When using MCB 112, choice [0] None
reference (see 3-15 Reference Resource 1 to
must always be selected.
3-17 Reference Resource 3).
[0] * None
FC 302 only.
[1] Analog input 53
[2] Analog input 54 NOTE!
[3] Digital input 18 Connection of KTY sensor between term.
[4] Digital input 19 54 and 55 (GND). See picture in section
[5] Digital input 32 KTY Sensor Connection.
[6] Digital input 33
[0] * None

MG33MD22 - VLT® is a registered Danfoss trademark 3-27

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

1-96 KTY Thermistor Resource of a machine current greater than 1.5 times the rated
Option: Function: current, shut down is immediate.

[2] Analog 1-99 ATEX ETR interpol points current

3 3 input 54 FC 302 only.

Only visible if 1-90 Motor Thermal Protection is set to [20] or [21].
1-97 KTY Threshold level
Range: Function:
Range: Function:
Application [0 - 100 %] Definition of thermal
80 C* [-40 - 140 C]
dependent* limitation curve. For
1-98 ATEX ETR interpol. points freq. example, see 1-98 ATEX
FC 302 only. ETR interpol. points freq.
Only visible if 1-90 Motor Thermal Protection is set to [20].
Use the four current points [A] from the motor nameplate.
Range: Function: Calculate the values as percentage of nominal motor
Application [Application Definition of current, Im/Im,n x 100 [%], and enter into this array.
dependent* dependant] thermal limitation
curve.
Together with 1-98 ATEX ETR interpol. points freq., these
make up a table (f [Hz],I [%]).
Enter the four frequency points [Hz] from the motor
nameplate into this array. Together with 1-99 ATEX ETR
interpol points current, these make up a table (f [Hz],I [%]). NOTE!
All frequency/current limit points from the motor
nameplate or motor data sheet must be programmed.
NOTE!
All frequency/current limit points from the motor
nameplate or motor data sheet must be programmed.
130BB909.10

100%

80 %

40 %

5 Hz 15 Hz 25 Hz 50 Hz
Figure 3.7 Example of ATEX ETR thermal limitation curve.
x-axis: fm [Hz]
y-axis: Im/Im,n x 100 [%]

1-98 ATEX ETR interpol. points freq. 1-99 ATEX ETR interpol points
current
[0] = 5 Hz [0] = 40%
[1] = 15 Hz [1] = 80%
[2] = 25 Hz [2] = 100%
[3] = 50 Hz [3] = 100%

All operating points underneath the curve are allowed

continuously. Above the line, however, only for a limited
time calculated as a function of the overload. In the event

3-28 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.4 Parameters: 2-** Brakes 2-03 DC Brake Cut In Speed [RPM]

Range: Function:
3.4.1 2-0* DC Brakes
Application [Application Set the DC brake cut-in

Parameter group for configuring the DC brake and DC

hold functions.
dependent* dependant] speed for activation of the
DC braking current set in 3 3
2-01 DC Brake Current, upon
2-00 DC Hold Current a stop command.
Range: Function:
2-04 DC Brake Cut In Speed [Hz]
50 [Application Enter a value for holding current as a
%* dependant] percentage of the rated motor current Range: Function:
IM,N set in 1-24 Motor Current. 100% DC Application dependent* [Application dependant]
holding current corresponds to IM,N.
This parameter holds the motor function 3.4.2 2-1* Brake Energy Funct.
(holding torque) or pre-heats the motor.
This parameter is active if DC hold is Parameter group for selecting dynamic braking parameters.
selected in 1-72 Start Function [0] or Only valid for drives with brake chopper.
1-80 Function at Stop [1].
2-10 Brake Function
NOTE! Option: Function:
The maximum value depends on the rated motor current. [0] * Off No brake resistor is installed.
Avoid 100% current for too long. It may damage the
[1] Resistor A brake resistor is incorporated in the system,
motor.
brake for dissipating surplus brake energy as heat.
Low values of DC hold will produce larger than expected
Connecting a brake resistor allows a higher DC
currents with larger motor power sizes. This error will
link voltage during braking (generating
increase as the motor power increases.
operation). The resistor brake function is only
active in adjustable frequency drives with an
2-01 DC Brake Current integral dynamic brake.
Range: Function: [2] AC brake Is selected to improve braking without using a
50 [Application Enter a value for current as a percentage brake resistor. This parameter controls an
%* dependant] of the rated motor current IM,N, see overmagnetization of the motor when running
1-24 Motor Current. 100% DC braking with a generatoric load. This function can
current corresponds to IM,N. improve the OVC function. Increasing the
DC brake current is applied on a stop electrical losses in the motor allows the OVC
command, when the speed is lower than function to increase the braking torque without
the limit set in 2-03 DC Brake Cut In Speed exceeding the overvoltage limit. Please note
[RPM]; when the DC Brake Inverse function that AC brake is not as effective as dynamic
is active; or via the serial communication breaking with resistor.
port. The braking current is active during AC brake is for VVCplus and flux mode in both
the time period set in 2-02 DC Braking open-loop and closed-loop.
Time.
2-11 Brake Resistor (ohm)
NOTE! Range: Function:
The maximum value depends on the rated motor current.
Size related* [ 5.00 - 65535.00 Ohm]
Avoid 100% current for too long. It may damage the
motor. 2-12 Brake Power Limit (kW)
Range: Function:
2-02 DC Braking Time Size related* [ 0.001 - 2000.000 kW]
Range: Function:
10.0 s* [0.0 - 60.0 s] Set the duration of the DC braking
current set in 2-01 DC Brake Current, once
activated.

MG33MD22 - VLT® is a registered Danfoss trademark 3-29

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

2-13 Brake Power Monitoring 2-15 Brake Check

Option: Function: Option: Function:
This parameter is only active in adjustable 1. The DC link ripple amplitude is

3 3 frequency drives with an integral dynamic

brake. 2.
measured for 300 ms without braking.

The DC link ripple amplitude is

This parameter enables monitoring of the measured for 300 ms with the brake
power to the brake resistor. The power is turned on.
calculated on the basis of the resistance
3. If the DC link ripple amplitude while
(2-11 Brake Resistor (ohm)), the DC-link voltage,
braking is lower than the DC link ripple
and the resistor duty time.
amplitude before braking + 1%: Brake
[0] * Off No braking energy monitoring required. check has failed by returning a warning
[1] Warning Activates a warning on the display when the or alarm.
power transmitted over 120 s exceeds 100% of 4. If the DC link ripple amplitude while
the monitoring limit (2-12 Brake Power Limit braking is higher than the DC link
(kW)). ripple amplitude before braking + 1%:
The warning disappears when the transmitted Brake check is OK.
power falls below 80% of the monitoring limit.
[0] Off Monitors brake resistor and brake IGBT for a
[2] Trip Trips Adjustable frequency drive and displays * short-circuit during operation. If a short-circuit
an alarm when the calculated power exceeds occurs, warning 25 appears.
100% of the monitoring limit.
[1] Warning Monitors brake resistor and brake IGBT for a
[3] Warning Activates both of the above, including short-circuit, and runs a test for brake resistor
and trip warning, trip and alarm. disconnection during power-up.

If power monitoring is set to Off [0] or Warning [1], the [2] Trip Monitors for a short-circuit or disconnection of
brake function remains active, even if the monitoring limit the brake resistor, or a short-circuit of the brake
is exceeded. This may lead to thermal overload of the IGBT. If a fault occurs, the Adjustable frequency
resistor. It is also possible to generate a warning via a drive cuts out while displaying an alarm (trip
relay/digital output. The measuring accuracy of the power locked).
monitoring depends on the accuracy of the resistance of [3] Stop and Monitors for a short-circuit or disconnection of
the resistor (better than ± 20%). trip the brake resistor, or a short-circuit of the brake
IGBT. If a fault occurs, the Adjustable frequency
2-15 Brake Check
drive ramps down to coast and then trips. A trip
Option: Function: lock alarm is displayed (e.g., warning 25, 27 or
Select type of test and monitoring function to 28).
check the connection to the brake resistor, or
[4] AC brake Monitors for a short-circuit or disconnection of
whether a brake resistor is present, and then
the brake resistor, or a short-circuit of the brake
display a warning or an alarm in the event of a
IGBT. If a fault occurs, the Adjustable frequency
fault.
drive performs a controlled ramp-down. This
NOTE! option is available for FC 302 only.
The brake resistor disconnection function is
[5] Trip Lock
tested during power-up. However, the
brake IGBT test is performed when there is NOTE!
no braking. A warning or trip disconnects Remove a warning arising in connection with Off [0] or
the brake function. Warning [1] by cycling the line power supply. The fault
must be corrected first. For Off [0] or Warning [1], the
The testing sequence is as follows: Adjustable frequency drive keeps running even if a fault is
located.

This parameter is only active in adjustable frequency drives

with an integral dynamic brake.

3-30 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

2-16 AC brake Max. Current 3.4.3 2-2* Mechanical Brake

Range: Function:
100.0 %* [Application dependant]
Parameters for controlling operation of an electro-
magnetic (mechanical) brake, typically required in hoisting
NOTE! applications. 3 3
2-16 AC brake Max. Current will not have effect when To control a mechanical brake, a relay output (relay 01 or
1-10 Motor Construction = [1] PM, non-salient SPM. relay 02) or a programmed digital output (terminal 27 or
29) is required. Normally this output must be closed during
periods when the Adjustable frequency drive is unable to
2-17 Over-voltage Control
‘hold’ the motor, e.g., due to an excessive load. Select
Option: Function: Mechanical Brake Control [32] for applications with an
Overvoltage control (OVC) reduces the risk electro-magnetic brake in 5-40 Function Relay, 5-30 Terminal
of the Adjustable frequency drive tripping 27 Digital Output, or 5-31 Terminal 29 Digital Output. When
due to an overvoltage on the DC link selecting Mechanical brake control [32], the mechanical
caused by generative power from the load. brake is closed from start up until the output current is
[0] * Disabled No OVC required. above the level selected in 2-20 Release Brake Current.
During stop, the mechanical brake activates when the
[1] Enabled (not Activates OVC except when using a stop
speed falls below the level specified in 2-21 Activate Brake
at stop) signal to stop the Adjustable frequency
Speed [RPM]. If the Adjustable frequency drive enters an
drive.
alarm condition or an overcurrent or overvoltage situation,
[2] Enabled Activates OVC. the mechanical brake immediately cuts in. This is also the
case during safe stop.
NOTE!
OVC must not be enabled in hoisting applications. NOTE!
Protection mode and trip delay features (14-25 Trip Delay
2-18 Brake Check Condition at Torque Limit and 14-26 Trip Delay at Inverter Fault) may
Range: Function: delay the activation of the mechanical brake in an alarm
[0] * At Power Up Brake check will be performed at
condition. These features must be disabled in hoisting
power-up
applications.

[1] After Coast Situations Brake check will be performed after

coast situations

2-19 Over-voltage Gain

Range: Function:
100 %* [0 - 200 %] Select overvoltage gain.

MG33MD22 - VLT® is a registered Danfoss trademark 3-31

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

130BA074.12
Start 1=on
term.18 0=off
3 3 Par 1-71
Start delay time
Par 2-21
Activate brake
Shaft speed speed
Par 1-74
Start speed
Output current

Pre-magnetizing
current or
DC hold current Par 2-20
Par 1-76 Start current/
Release brake current
Par 2-23 Par 2-00 DC hold current
Brake delay time

Reaction time EMK brake

on
Relay 01
off
Mechanical brake
locked
Mechanical brake
free
Time

2-20 Release Brake Current 2-22 Activate Brake Speed [Hz]

Range: Function: Range: Function:
Application [Application Set the motor current for release Application dependent* [Application dependant]
dependent* dependant] of the mechanical brake, when a
start condition is present. The
2-23 Activate Brake Delay
default value is the maximum Range: Function:
current the inverter can provide 0.0 s* [0.0 - Enter the brake delay time of the coast after
for the particular power size. The 5.0 s] ramp-down time. The shaft is held at zero
upper limit is specified in speed with full holding torque. Ensure that the
16-37 Inv. Max. Current. mechanical brake has locked the load before

NOTE! the motor enters coast mode. See the

Mechanical Brake Control section in the Design
When Mechanical brake
Guide.
control output is selected but
no mechanical brake is
2-24 Stop Delay
connected, the function will
not work by default setting Range: Function:
due to too low motor current. 0.0 s* [0.0 - 5.0 s] Set the time interval from the moment
when the motor is stopped until the brake
closes. This parameter is a part of the
2-21 Activate Brake Speed [RPM] stopping function.
Range: Function:
2-25 Brake Release Time
Application [0 - 30000 Set the motor speed for
dependent* RPM] activation of the mechanical Range: Function:
brake, when a stop condition is 0.20 s* [0.00 - 5.00 This value defines the time it takes for
present. The upper speed limit is s] the mechanical brake to open. This
specified in 4-53 Warning Speed parameter must act as a timeout when
High. brake feedback is activated.

3-32 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

2-26 Torque Ref 2-28 Gain Boost Factor

Range: Function: Range: Function:
0.00 %* [Application The value defines the torque 1.00* [1.00 - Only active in flux closed-loop. The function
dependant] applied against the closed
mechanical brake before release
4.00 ] ensures a smooth transition from torque
control mode to speed control mode when 3 3
the motor takes over the load from the
2-27 Torque Ramp Time brake.
Range: Function:
0.2 s* [0.0 - 5.0 s] The value defines the duration of the torque
ramp in clockwise direction.

130BA642.12
II

MotorSpeed
Premag Torque Ramp Brake Ramp 1 upp. 3-41 Ramp 1 downp. 3-42 Stop Activate
Time Release Delay Brake
p. 2-27 Time p. 2-24 Delay
p. 2-25 p. 2-23
Torque Ref. 2-26

Torqueref.

Relay
Gain Boost Factor
p. 2-28
GainBoost

Mech.Brake

1 2 3

Figure 3.8 Brake release sequence for hoist mechanical brake control
I) Activate brake delay: The Adjustable frequency drive starts again from the mechanical brake engaged position.
II) Stop delay: When the time between successive starts is shorter than the setting in 2-24 Stop Delay, the Adjustable frequency drive starts
without applying the mechanical brake (e.g., reversing).

MG33MD22 - VLT® is a registered Danfoss trademark 3-33

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.5 Parameters: 3-** Reference / Ramps 3-01 Reference/Feedback Unit

Option: Function:
Parameters for reference handling, definition of limitations,
[41] m/min
and configuration of the reaction of the Adjustable
3 3 frequency drive to changes. [45]
[60]
m
°C
[70] mbar
3.5.1 3-0* Reference Limits
[71] bar
[72] Pa
3-00 Reference Range
[73] kPa
Option: Function: [74] m WG
Select the range of the reference signal and the [80] kW
feedback signal. Signal values can be positive [120] GPM
only, or positive and negative. The minimum [121] gal/s
limit may have a negative value, unless Speed
[122] gal/min
closed-loop [1] control or Process [3] is selected in
[123] gal/h
1-00 Configuration Mode.
[124] CFM
[0] Min - Select the range of the reference signal and the [125] ft³/s
Max feedback signal. Signal values can be positive [126] ft³/min
only, or positive and negative. The minimum [127] ft³/h
limit may have a negative value, unless Speed
[130] lb/s
closed-loop [1] control or Process [3] is selected in
[131] lb/min
1-00 Configuration Mode.
[132] lb/h
[1] * -Max - For both positive and negative values (both [140] ft/s
+Max directions, relative to 4-10 Motor Speed Direction). [141] ft/min
[145] ft
3-01 Reference/Feedback Unit [150] lb ft
Option: Function: [160] °F
Select the unit to be used in process PID control [170] psi
references and feedback. 1-00 Configuration Mode [171] lb/in²
must be either [3] Process or [8] Extended PID [172] in WG
Control. [173] ft WG
[0] * None [180] HP
[1] %
3-02 Minimum Reference
[2] RPM
Range: Function:
[3] Hz
[4] Nm Application Enter the Minimum Reference. The
dependent* [Application Minimum Reference is the lowest
[5] PPM
dependant] value obtainable by summing all
[10] 1/min
references.
[12] Pulse/s
Minimum Reference is active only
[20] l/s
when 3-00 Reference Range is set to
[21] l/min
Min.- Max. [0].
[22] l/h
The minimum reference unit
[23] m³/s matches:
[24] m³/min
[25] m³/h
• The choice of configuration
in 1-00 Configuration Mode
[30] kg/s
Configuration Mode: for
[31] kg/min
[32] kg/h
[33] t/min
[34] t/h
[40] m/s

3-34 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3-02 Minimum Reference

Range: Function:
Speed closed-loop [1], RPM;

•
for Torque [2], Nm.

The unit selected in

3 3
3-01 Reference/Feedback
Unit.

3-03 Maximum Reference

Range: Function:
Application [Application Enter the maximum reference. The
dependent* dependant] maximum reference is the highest
value obtainable by adding all
references together.
Preset ref. bit 2 1 0
The Maximum Reference unit
Preset ref. 0 0 0 0
matches:
Preset ref. 1 0 0 1
• The choice of configu- Preset ref. 2 0 1 0
ration in 1-00 Configuration
Preset ref. 3 0 1 1
Mode: for Speed closed-loop
Preset ref. 4 1 0 0
[1], RPM; for Torque [2],
Preset ref. 5 1 0 1
Nm.
Preset ref. 6 1 1 0
• The unit selected in
Preset ref. 7 1 1 1
3-00 Reference Range.

3-04 Reference Function 3-11 Jog Speed [Hz]

Option: Function: Range: Function:
[0] * Sum Sums both external and preset reference Application [Application The jog speed is a fixed
sources. dependent* dependant] output speed at which the
Adjustable frequency drive is
[1] External/Preset Use either the preset or the external
running when the jog
reference source.
function is activated.
Shift between external and preset via a
See also 3-80 Jog Ramp Time.
command on a digital input.

3-12 Catch up/slow Down Value

3.5.2 3-1* References Range: Function:
0.00 %* [0.00 - 100.00 %]
Select the preset reference(s). Select Preset ref. bit 0 / 1 / 2
[16], [17] or [18] for the corresponding digital inputs in 3-13 Reference Site
parameter group 5-1*. Option: Function:
Select which reference site to activate.
3-10 Preset Reference
Array [8] [0] * Linked to Use local reference when in hand mode; or
Range: 0-7 Hand / Auto remote reference when in auto mode.

Range: Function: [1] Remote Use remote reference in both hand mode
0.00 %* [-100.00 - 100.00 %] and auto mode.

[2] Local Use local reference in both hand mode and

auto mode.

NOTE!
When set to Local [2], the Adjustable
frequency drive will start with this
setting again following a 'power-down'.

MG33MD22 - VLT® is a registered Danfoss trademark 3-35

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3-14 Preset Relative Reference 3-16 Reference Resource 2

Range: Function: Option: Function:
0.00 %* [-100.00 - 100.00 %] [0] No function

3 3 [1] Analog input 53

130BA059.12
Y
Relative Z Resulting [2] Analog input 54
actual
X Z=X+X*Y/100 reference [7] Frequency input 29
[8] Frequency input 33
[11] Local bus reference
[20] * Digital pot.meter

130BA278.10
Z
[21] Analog input X30-11
0
*Y /10
X+X
[22] Analog input X30-12
[29] Analog Input X48/2
X
3-17 Reference Resource 3
Option: Function:
Select the reference input to be
Y
used for the third reference signal.
-100 0 100 %
3-15 Reference Resource 1,
P 3-14
3-16 Reference Resource 2 and
3-17 Reference Resource 3 define up
3-15 Reference Resource 1 to three different reference signals.
Option: Function: The sum of these reference signals
defines the actual reference.
Select the reference input to be used
for the first reference signal. [0] No function
3-15 Reference Resource 1, [1] Analog input 53
3-16 Reference Resource 2 and [2] Analog input 54
3-17 Reference Resource 3 define up to [7] Frequency input 29
three different reference signals. The [8] Frequency input 33
sum of these reference signals [11] * Local bus reference
defines the actual reference. [20] Digital pot.meter
[0] No function [21] Analog input X30-11
[1] * Analog input 53 [22] Analog input X30-12
[2] Analog input 54 [29] Analog Input X48/2
[7] Frequency input 29
3-18 Relative Scaling Reference Resource
[8] Frequency input 33
[11] Local bus reference Option: Function:
[20] Digital pot.meter Select a variable value to be added to the
[21] Analog input X30-11 (General Purpose I/O Option Module) fixed value (defined in 3-14 Preset Relative
Reference). The sum of the fixed and
[22] Analog input X30-12 (General Purpose I/O Option Module) variable values (labeled Y in the figure
[29] Analog Input X48/2 below) is multiplied by the actual reference
(labeled X in the figure below). The result
3-16 Reference Resource 2 is then added to the actual reference (X
Option: Function: +X*Y/100) to give the resulting actual
Select the reference input to be reference.
used for the second reference
130BA059.12

Y
signal. 3-15 Reference Resource 1, Relative Z Resulting
actual
X Z=X+X*Y/100 reference
3-16 Reference Resource 2 and
3-17 Reference Resource 3 define up
to three different reference signals.
The sum of these reference signals [0] * No function
defines the actual reference.

3-36 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3-18 Relative Scaling Reference Resource

130BA872.10
RPM
Option: Function:
P 4-13
[1] Analog input High-limit

3 3
53 Reference
ns
[2] Analog input P 4-11
Low limit
54
[7] Frequency
P 3-*1 P 3-*2 Time
input 29 Ramp (X)Up Ramp (X) Down
Time (Acc) Time (Dec)
[8] Frequency
tacc tdec
input 33
[11] Local bus
reference If S-ramps are selected, then set the level of non-linear jerk
[20] Digital compensation required. Set jerk compensation by defining
pot.meter the proportion of ramp-up and ramp-down times where
[21] Analog input acceleration and deceleration are variable (i.e., increasing
X30-11 or decreasing). The S-ramp acceleration and deceleration
[22] Analog input settings are defined as a percentage of the actual ramp
X30-12 time.
[29] Analog Input
X48/2

NOTE!
This parameter cannot be adjusted while the motor is
running.

3-19 Jog Speed [RPM]

Range: Function:
Application [Application Enter a value for the jog speed
dependent* dependant] nJOG, which is a fixed output
speed. The Adjustable frequency
drive runs at this speed when
the jog function is activated. The
maximum limit is defined in 3-40 Ramp 1 Type
4-13 Motor Speed High Limit Option: Function:
[RPM].
Select the ramp type, depending on
See also 3-80 Jog Ramp Time.
requirements for acceleration/deceleration.
A linear ramp will give constant acceleration
3.5.3 Ramps during ramping. An S-ramp will give non-
3-4* Ramp 1 linear acceleration, compensating for jerk in
the application.
For each of four ramps (parameter groups 3-4*, 3-5*, 3-6* [0] * Linear
and 3-7*), configure the ramp parameters: ramp type, [1] S-ramp Acceleration with lowest possible jerk.
ramping times (duration of acceleration and deceleration) Const Jerk
and level of jerk compensation for S ramps. [2] S-ramp S-ramp based on the values set in 3-41 Ramp
Const Time 1 Ramp up Time and 3-42 Ramp 1 Ramp Down
Start by setting the linear ramping times corresponding to Time.
the figures.

MG33MD22 - VLT® is a registered Danfoss trademark 3-37

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

NOTE! 3-46 Ramp 1 S-ramp Ratio at Accel. End

If S-ramp [1] is selected and the reference during ramping Range: Function:
is changed, the ramp time may be prolonged in order to 50 %* [Application Enter the proportion of the total
realize a jerk-free movement, which may result in a longer
3 3 start or stop time.
dependant] ramp-up time (3-41 Ramp 1 Ramp up
Time) in which the acceleration torque
Additional adjustment of the S-ramp ratios or switching decreases. The larger the percentage
initiators may be necessary. value, the greater the jerk compen-
sation achieved, and thus the lower
3-41 Ramp 1 Ramp up Time the torque jerks in the application.
Range: Function:
3-47 Ramp 1 S-ramp Ratio at Decel. Start
Application Enter the ramp-up time, i.e., the
dependent* [Application acceleration time from 0RPM to the Range: Function:
dependant] synchronous motor speed nS. Choose 50 %* [Application Enter the proportion of the total
a ramp-up time such that the output dependant] ramp-down time (3-42 Ramp 1 Ramp
current does not exceed the current Down Time) where the deceleration
limit in 4-18 Current Limit during torque increases. The larger the
ramping. The value 0.00 corresponds percentage value, the greater the jerk
to 0.01 sec. in speed mode. See compensation achieved, and thus the
ramp-down time in 3-42 Ramp 1 lower the torque jerks in the
Ramp Down Time. application.
tacc s x ns RPM
Par . 3 − 41 = 3-48 Ramp 1 S-ramp Ratio at Decel. End
ref RPM

Range: Function:
3-42 Ramp 1 Ramp Down Time
50 %* [Application Enter the proportion of the total
Range: Function:
dependant] ramp-down time (3-42 Ramp 1 Ramp
Application Enter the ramp-down time, i.e., the Down Time) where the deceleration
dependent* [Application deceleration time from the torque decreases. The larger the
dependant] synchronous motor speed ns to 0 percentage value, the greater the jerk
RPM. Choose a ramp-down time such compensation achieved, and thus the
that no overvoltage arises in the lower the torque jerks in the
inverter due to regenerative application.
operation of the motor, and such
that the generated current does not
exceed the current limit set in 3.5.4 3-5* Ramp 2
4-18 Current Limit. The value 0.00
corresponds to 0.01 s in speed mode. Choosing ramp parameters, see parameter group 3-4*.
See ramp-up time in 3-41 Ramp 1
3-50 Ramp 2 Type
Ramp up Time.
Option: Function:
tdec s x ns RPM
Par . 3 − 42 = Select the ramp type, depending on
ref RPM
requirements for acceleration/deceleration. A
3-45 Ramp 1 S-ramp Ratio at Accel. Start linear ramp will give constant acceleration
Range: Function: during ramping. An S-ramp will give non-
50 %* [Application Enter the proportion of the total linear acceleration, compensating for jerk in
dependant] ramp-up time (3-41 Ramp 1 Ramp up the application.
Time) in which the acceleration torque [0] * Linear
increases. The larger the percentage [1] S-ramp Acceleration with lowest possible jerk
value, the greater the jerk compen- Const Jerk
sation achieved, and thus the lower [2] S-ramp S-ramp based on the values set in 3-51 Ramp
the torque jerks occurring in the Const Time 2 Ramp up Time and 3-52 Ramp 2 Ramp down
application. Time

3-38 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

NOTE! 3-56 Ramp 2 S-ramp Ratio at Accel. End

If S-ramp [1] is selected and the reference during ramping Range: Function:
is changed, the ramp time may be prolonged in order to 50 %* [Application Enter the proportion of the total
realize a jerk-free movement, which may result in a longer
start or stop time.
dependant] ramp-up time (3-51 Ramp 2 Ramp up
Time) in which the acceleration torque 3 3
Additional adjustment of the S-ramp ratios or switching decreases. The larger the percentage
initiators may be necessary. value, the greater the jerk compen-
sation achieved, and thus the lower
3-51 Ramp 2 Ramp up Time the torque jerks in the application.
Range: Function:
3-57 Ramp 2 S-ramp Ratio at Decel. Start
Application Enter the ramp-up time, i.e., the
dependent* [Application acceleration time from 0 RPM to the Range: Function:
dependant] rated motor speed ns. Choose a 50 %* [Application Enter the proportion of the total
ramp-up time such that the output dependant] ramp-down time (3-52 Ramp 2 Ramp
current does not exceed the current down Time) where the deceleration
limit in 4-18 Current Limit during torque increases. The larger the
ramping. The value 0.00 corresponds percentage value, the greater the jerk
to 0.01 sec. in speed mode. See compensation achieved, and thus the
ramp-down time in 3-52 Ramp 2 lower the torque jerks in the
Ramp down Time. application.
tacc s x ns RPM
Par . 3 − 51 = 3-58 Ramp 2 S-ramp Ratio at Decel. End
ref RPM

Range: Function:
3-52 Ramp 2 Ramp down Time
50 %* [Application Enter the proportion of the total
Range: Function:
dependant] ramp-down time (3-52 Ramp 2 Ramp
Application Enter the ramp-down time, i.e., the down Time) where the deceleration
dependent* [Application deceleration time from the rated torque decreases. The larger the
dependant] motor speed ns to 0 RPM. Choose a percentage value, the greater the jerk
ramp-down time such that no compensation achieved, and thus the
overvoltage arises in the inverter due lower the torque jerks in the
to regenerative operation of the application.
motor, and such that the generated
current does not exceed the current
limit set in 4-18 Current Limit. The 3.5.5 3-6* Ramp 3
value 0.00 corresponds to 0.01 sec. in
speed mode. See ramp-up time in Configure ramp parameters, see 3-4*.
3-51 Ramp 2 Ramp up Time.
3-60 Ramp 3 Type
tdec s x ns RPM
Par . 3 − 52 =
ref RPM
Option: Function:
Select the ramp type, depending on
3-55 Ramp 2 S-ramp Ratio at Accel. Start requirements for acceleration and
Range: Function: deceleration. A linear ramp will give constant
50 %* [Application Enter the proportion of the total acceleration during ramping. An S-ramp will
dependant] ramp-up time (3-51 Ramp 2 Ramp up give non-linear acceleration, compensating
Time) in which the acceleration torque for jerk in the application.
increases. The larger the percentage [0] * Linear
value, the greater the jerk compen- [1] S-ramp Accelerates with lowest possible jerk.
sation achieved, and thus the lower Const Jerk
the torque jerks in the application. [2] S-ramp S-ramp based on the values set in 3-61 Ramp
Const Time 3 Ramp up Time and 3-62 Ramp 3 Ramp down
Time

MG33MD22 - VLT® is a registered Danfoss trademark 3-39

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

NOTE! 3-66 Ramp 3 S-ramp Ratio at Accel. End

If S-ramp [1] is selected and the reference during ramping Range: Function:
is changed, the ramp time may be prolonged in order to 50 %* [Application Enter the proportion of the total
realize a jerk-free movement, which may result in a longer
3 3 start or stop time.
dependant] ramp-up time (3-61 Ramp 3 Ramp up
Time) in which the acceleration torque
Additional adjustment of the S-ramp ratios or switching decreases. The larger the percentage
initiators may be necessary. value, the greater the jerk compen-
sation achieved, and thus the lower
3-61 Ramp 3 Ramp up Time the torque jerks in the application.
Range: Function:
3-67 Ramp 3 S-ramp Ratio at Decel. Start
Application [Application Enter the ramp-up time, i.e., the
dependent* dependant] acceleration time from 0 RPM to Range: Function:
the rated motor speed ns. 50 %* [Application Enter the proportion of the total
Choose a ramp-up time such that dependant] ramp-down time (3-62 Ramp 3 Ramp
the output current does not down Time) where the deceleration
exceed the current limit in torque increases. The larger the
4-18 Current Limit during percentage value, the greater the jerk
ramping. The value 0.00 compensation achieved, and thus the
corresponds to 0.01 sec. in speed lower the torque jerks in the
mode. See ramp-down time in application.
3-62 Ramp 3 Ramp down Time.
3-68 Ramp 3 S-ramp Ratio at Decel. End
3-62 Ramp 3 Ramp down Time Range: Function:
Range: Function: 50 %* [Application Enter the proportion of the total
Application Enter the ramp-down time, i.e., the dependant] ramp-downdecel time (3-62 Ramp 3
dependent* [Application deceleration time from the rated Ramp down Time) where the
dependant] motor speed ns to 0 RPM. Choose a deceleration torque decreases. The
ramp-down time such that no larger the percentage value, the
overvoltage arises in the inverter due greater the jerk compensation
to regenerative operation of the achieved, and thus the lower the
motor, and such that the generated torque jerks in the application.
current does not exceed the current
limit set in 4-18 Current Limit. The
value 0.00 corresponds to 0.01 sec. in
3.5.6 3-7* Ramp 4
speed mode. See ramp-up time in
3-61 Ramp 3 Ramp up Time. Configure ramp parameters, see 3-4*.

tdec s x ns RPM 3-70 Ramp 4 Type

Par . 3 − 62 =
ref RPM
Option: Function:
3-65 Ramp 3 S-ramp Ratio at Accel. Start Select the ramp type, depending on
requirements for acceleration and
Range: Function:
deceleration. A linear ramp will give constant
50 %* [Application Enter the proportion of the total
acceleration during ramping. An S-ramp will
dependant] ramp-up time (3-61 Ramp 3 Ramp up
give non-linear acceleration, compensating
Time) in which the acceleration torque
for jerk in the application.
increases. The larger the percentage
value, the greater the jerk compen- [0] * Linear
sation achieved, and thus the lower [1] S-ramp Accelerates with lowest possible jerk.
the torque jerks in the application. Const Jerk
[2] S-ramp S-ramp based on the values set in 3-71 Ramp
Const Time 4 Ramp up Time and 3-72 Ramp 4 Ramp Down
Time.

3-40 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

NOTE! 3-76 Ramp 4 S-ramp Ratio at Accel. End

If S-ramp [1] is selected and the reference during ramping Range: Function:
is changed, the ramp time may be prolonged in order to 50 %* [Application Enter the proportion of the total
realize a jerk-free movement, which may result in a longer
start or stop time.
dependant] ramp-up time (3-71 Ramp 4 Ramp up
Time) in which the acceleration torque 3 3
Additional adjustment of the S-ramp ratios or switching decreases. The larger the percentage
initiators may be necessary. value, the greater the jerk compen-
sation achieved, and thus the lower
3-71 Ramp 4 Ramp up Time the torque jerks in the application.
Range: Function:
3-77 Ramp 4 S-ramp Ratio at Decel. Start
Application Enter the ramp-up time, i.e., the
dependent* [Application acceleration time from 0 RPM to the Range: Function:
dependant] rated motor speed ns. Choose a 50 %* [Application Enter the proportion of the total
ramp-up time such that the output dependant] ramp-down time (3-72 Ramp 4 Ramp
current does not exceed the current Down Time) where the deceleration
limit in 4-18 Current Limit during torque increases. The larger the
ramping. The value 0.00 corresponds percentage value, the greater the jerk
to 0.01 sec. in speed mode. See compensation achieved, and thus the
ramp-down time in 3-72 Ramp 4 lower the torque jerks in the
Ramp Down Time. application.
tacc s x ns RPM
Par . 3 − 71 = 3-78 Ramp 4 S-ramp Ratio at Decel. End
ref RPM

Range: Function:
3-72 Ramp 4 Ramp Down Time
50 %* [Application Enter the proportion of the total
Range: Function:
dependant] ramp-down time (3-72 Ramp 4 Ramp
Application Enter the ramp-down time, i.e., the Down Time) where the deceleration
dependent* [Application deceleration time from the rated torque decreases. The larger the
dependant] motor speed ns to 0 RPM. Choose a percentage value, the greater the jerk
ramp-down time such that no compensation achieved, and thus the
overvoltage arises in the inverter due lower the torque jerks in the
to regenerative operation of the application.
motor, and such that the generated
current does not exceed the current
limit set in 4-18 Current Limit. The 3.5.7 3-8* Other Ramps
value 0.00 corresponds to 0.01 sec. in
speed mode. See ramp-up time in 3-80 Jog Ramp Time
3-71 Ramp 4 Ramp up Time.
Range: Function:
tdec s x ns RPM
Par . 3 − 72 = Application [0.01 - Enter the jog ramp time, i.e., the
ref RPM
dependent* 3600.00 s] acceleration/deceleration time
3-75 Ramp 4 S-ramp Ratio at Accel. Start between 0 RPM and the rated motor
frequency ns. Ensure that the resultant
Range: Function:
output current required for the given
50 %* [Application Enter the proportion of the total
jog ramp time does not exceed the
dependant] ramp-up time (3-71 Ramp 4 Ramp up
current limit in 4-18 Current Limit. The
Time) in which the acceleration torque
jog ramp time starts upon activation
increases. The larger the percentage
of a jog signal via the LCP, a selected
value, the greater the jerk compen-
digital input, or the serial communi-
sation achieved, and thus the lower
cation port. When jog state is
the torque jerks in the application.
disabled, the normal ramping times
are valid.

MG33MD22 - VLT® is a registered Danfoss trademark 3-41

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

130BA070.10
RPM

130BA069.10
RPM

P 4-13 RPM P 4-13 RPM

3 3 high limit

P 1-25
high limit

Reference
Motor speed
P 1-25
P 3-19 Motor speed
Jog speed

P 4-11 RPM P 4-11 RPM

low limit low limit
t jog t jog Time
P 3-80 P 3-80
Ramp up Ramp down Time
P 3-81
(acc) (dec)
Qramp

Qstop
tjog s x ns RPM
Par . 3 − 80 =
Δ log speed ( par . 3 − 19) RPM

3-81 Quick Stop Ramp Time tQstop s x ns RPM

Par . 3 − 81 =
Δ jog ref ( par . 3 − 19) RPM
Range: Function:
3-82 Quick Stop Ramp Type
Application [0.01 - Enter the quick stop ramp-down time,
Option: Function:
dependent* 3600.00 i.e., the deceleration time from the
s] synchronous motor speed to 0 RPM. Select the ramp type, depending on
Ensure that no resultant overvoltage requirements for acceleration and
will arise in the inverter due to deceleration. A linear ramp will give
regenerative operation of the motor constant acceleration during ramping. An
required to achieve the given ramp- S-ramp will give non-linear acceleration,
down time. Ensure also that the compensating for jerk in the application.
generated current required to achieve [0] * Linear
the given ramp-down time does not [1] S-ramp Const
exceed the current limit (set in Jerk
4-18 Current Limit). Quick stop is [2] S-ramp Const
activated by means of a signal on a Time
selected digital input, or via the serial
communication port. 3-83 Quick Stop S-ramp Ratio at Decel. Start
Application [0.01 - Bus only Range: Function:
dependent* 3600.00 50 %* [Application dependant]
Enter the quick stop ramp-down time,
s] i.e., the deceleration time from the 3-84 Quick Stop S-ramp Ratio at Decel. End
synchronous motor speed to 0 RPM.
Range: Function:
Ensure that no resultant overvoltage
50 %* [Application Enter the proportion of the total
will arise in the inverter due to
dependant] ramp-down time (3-42 Ramp 1 Ramp
regenerative operation of the motor
Down Time) where the deceleration
required to achieve the given ramp-
torque decreases. The larger the
down time. Ensure also that the
percentage value, the greater the jerk
generated current required to achieve
compensation achieved, and thus the
the given ramp-down time does not
lower the torque jerks in the
exceed the current limit (set in
application.
4-18 Current Limit). Quick stop is
activated by means of a signal on a
selected digital input, or via the serial 3.5.8 3-9* Digital Pot. meter
communication port.

The digital potentiometer function allows the user to

increase or decrease the actual reference by adjusting the
set-up of the digital inputs using the functions Increase,

3-42 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

Decrease or Clear. To activate the function, at least one 3-93 Maximum Limit
digital input must be set up to Increase or Decrease. Range: Function:
the Digital Potentiometer is used for fine
tuning of the resulting reference.
3 3
3-94 Minimum Limit
Range: Function:
-100 %* [-200 - 200 Set the minimum permissible value for
%] the resultant reference. This is advisable
if the Digital Potentiometer is used for
fine tuning of the resulting reference.

3-95 Ramp Delay

Range: Function:
Application [Application Enter the delay required from
dependent* dependant] activation of the digital potenti-
ometer function until the
Adjustable frequency drive starts
to ramp the reference. With a
delay of 0 ms, the reference
starts to ramp as soon as
INCREASE/DECREASE is activated.
3-90 Step Size
See also 3-91 Ramp Time.
Range: Function:
0.10 %* [0.01 - 200.00 %]

3-91 Ramp Time

Range: Function:
1.00 [0.00 - Enter the ramp time, i.e., the time for
s* 3600.00 s] adjustment of the reference from 0% to
100% of the specified digital potentiometer
function (Increase, Decrease or Clear).
If Increase/Decrease is activated for longer
than the ramp delay period specified in
3-95 Ramp Delay, the actual reference will be
ramped up/down according to this ramp
time. The ramp time is defined as the time
used to adjust the reference by the step size
specified in 3-90 Step Size.

3-92 Power Restore

Option: Function:
[0] * Off Resets the Digital Potentiometer reference to 0% after
power-up.

[1] On Restores the most recent Digital Potentiometer

reference at power-up.

3-93 Maximum Limit

Range: Function:
100 %* [-200 - 200 Set the maximum permissible value for
%] the resultant reference. This is advisable if

MG33MD22 - VLT® is a registered Danfoss trademark 3-43

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.6 Parameters: 4-** Limits/Warnings 4-14 Motor Speed High Limit [Hz]
Range: Function:
3.6.1 4-1* Motor Limits
Size related* [ par. 4-12 - par. 4-19 Hz]

3 3 Define torque, current and speed limits for the motor, and
the reaction of the Adjustable frequency drive when the
NOTE!
Max. output frequency cannot exceed 10% of the inverter
limits are exceeded. switching frequency (14-01 Switching Frequency).
A limit may generate a message on the display. A warning
will always generate a message on the display or on the
4-16 Torque Limit Motor Mode
serial communication bus. A monitoring function may
initiate a warning or a trip, upon which the Adjustable Range: Function:
frequency drive will stop and generate an alarm message. Application dependent* [Application dependant]

4-10 Motor Speed Direction NOTE!

Option: Function: Changing 4-16 Torque Limit Motor Mode when 1-00 Configu-
Select the motor speed direction(s) required. ration Mode is set to Speed open-loop [0], 1-66 Min. Current
Use this parameter to prevent unwanted at Low Speed is automatically readjusted.
reversing. When 1-00 Configuration Mode is
set to Process [3], 4-10 Motor Speed Direction is NOTE!
set to Clockwise [0] as default. The setting in The torque limit reacts on the actual, non-filtrated torque,
4-10 Motor Speed Direction does not limit including torque spikes. This is not the torque that is seen
options for setting 4-13 Motor Speed High from the LCP or the serial communication bus as that is
Limit [RPM]. filtered.
[0] * Clockwise The reference is set to CW rotation. Reversing
input (Default term 19) must be open. 4-17 Torque Limit Generator Mode
[1] Counter The reference is set to CCW rotation. Range: Function:
clockwise Reversing input (Default term 19) must be 100.0 %* [Application dependant]
closed. If reversing is required when ‘Reverse’
input is open, the motor direction can be NOTE!
changed by 1-06 Clockwise Direction The torque limit reacts on the actual, non-filtrated torque,
including torque spikes. This is not the torque that is seen
[2] Both Allows the motor to rotate in both directions.
from the LCP or the serial communication bus as that is
directions
filtered.
NOTE!
This parameter cannot be adjusted while the motor is 4-18 Current Limit
running. Range: Function:
Application dependent* [Application dependant]
4-11 Motor Speed Low Limit [RPM]
Range: Function:
NOTE!
If [20] is selected in 1-90 Motor Thermal Protection,
Application dependent* [Application dependant]
4-18 Current Limit current limit must be set to 150%.
4-12 Motor Speed Low Limit [Hz]
Range: Function: 4-19 Max Output Frequency
Application dependent* [Application dependant] Range: Function:
132.0 [1.0 - Provides a final limit on the output
4-13 Motor Speed High Limit [RPM]
Hz* 1000.0 Hz] frequency for improved safety in
Range: Function: applications where you want to avoid
Application dependent* [Application dependant] accidental overspeeding. This limit is
final in all configurations (independent
NOTE! of the setting in 1-00 Configuration
Max. output frequency cannot exceed 10% of the inverter Mode).
switching frequency (14-01 Switching Frequency).

3-44 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

NOTE! 4-21 Speed Limit Factor Source Option

This parameter cannot be adjusted while the motor is Option: Function:
running. [14] Analog input X30-12

NOTE!
[16] Analog input X30-12
inv 3 3
Max. output frequency cannot exceed 10% of the inverter
switching frequency (14-01 Switching Frequency). 3.6.2 4-3* Motor Feedback Monitoring

4-20 Torque Limit Factor Source The parameter group includes monitoring and handling of
Option: Function: motor feedback devices such as encoders, resolvers, etc.
Select an analog input for scaling the 4-30 Motor Feedback Loss Function
settings in 4-16 Torque Limit Motor
Option: Function:
Mode and 4-17 Torque Limit Generator
Select which reaction the Adjustable
Mode from 0% to 100% (or inverse).
frequency drive should take if a
The signal levels corresponding to
feedback fault is detected. The
0% and 100% are defined in the
selected action is to take place when
analog input scaling, e.g., parameter
the feedback signal differs from the
group 6-1*. This parameter is only
output speed where its range is
active when 1-00 Configuration Mode
specified in 4-31 Motor Feedback
is in Speed Open-loop or Speed
Speed Error during its time frame set
Closed-loop.
in 4-32 Motor Feedback Loss Timeout.
[0] * No function
[0] Disabled
[2] Analog in 53
[1] Warning
[4] Analog in 53 inv
[2] * Trip
[6] Analog in 54
[3] Jog
[8] Analog in 54 inv
[4] Freeze Output
[10] Analog in X30-11
[5] Max Speed
[12] Analog in X30-11
[6] Switch to Open Loop
inv
[7] Select Setup 1
[14] Analog in X30-12
[8] Select Setup 2
[16] Analog in X30-12
[9] Select Setup 3
inv
[10] Select Setup 4
4-21 Speed Limit Factor Source Option [11] stop & trip
Option: Function: Warning/Alarm 61 Feedback Error is related to the Motor
Select an analog input for scaling Feedback Loss Function.
the settings in 4-19 Max Output
Frequency from 0% to 100% (or vice 4-31 Motor Feedback Speed Error
versa). The signal levels Range: Function:
corresponding to 0% and 100% are 300 RPM* [1 - 600 RPM] Select the max. allowed tracking error
defined in the analog input scaling, in speed from the calculated and the
e.g., parameter group 6-1*. This actual mechanical shaft output
parameter is only active when speeds.
1-00 Configuration Mode is in Torque
Mode.
[0] * No function
[2] Analog input 53
[4] Analog input 53 inv
[6] Analog input 54
[8] Analog input 54 inv
[10] Analog input X30-11
[12] Analog input X30-11
inv

MG33MD22 - VLT® is a registered Danfoss trademark 3-45

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

4-35 Tracking Error

Range: Function:
10 RPM* [1 - 600 Enter the maximum permissible speed

3 3 RPM] error between the motor speed and the

output of the ramp when not ramping. In
open-loop, the motor speed is estimated,
and in closed-loop, it is the feedback from
encoder/resolver.

4-36 Tracking Error Timeout

Range: Function:
1.00 s* [0.00 - 60.00 s] Enter the timeout period during which
an error greater than the value set in
4-35 Tracking Error is permissible.

4-37 Tracking Error Ramping

Range: Function:
4-32 Motor Feedback Loss Timeout 100 RPM* [1 - 600 Enter the maximum permissible speed
Range: Function: RPM] error between the motor speed and the
0.05 s* [0.00 - 60.00 s] Set the timeout value allowing the output of the ramp when ramping. In
speed error set in 4-31 Motor Feedback open-loop, the motor speed is estimated,
Speed Error to be exceeded. and in closed-loop, it is the feedback
from encoder/resolver.
4-34 Tracking Error Function
4-38 Tracking Error Ramping Timeout
Option: Function:
Select which reaction the Adjustable frequency
Range: Function:
drive should take if a tracking error is detected. 1.00 s* [0.00 - 60.00 Enter the timeout period during which
Closed-loop: The tracking error is measured s] an error greater than the value set in
between the output from the ramp generator 4-37 Tracking Error Ramping while
and the speed feedback (filtered). ramping is permissible.
Open-loop: The tracking error is measured
between the output from the ramp generator - 4-39 Tracking Error After Ramping Timeout
compensated for slip - and the frequency that Range: Function:
is sent to the motor (16-13 Frequency). 5.00 s* [0.00 - 60.00 s] Enter the timeout period after ramping
The reaction will be activated if the measured where 4-37 Tracking Error Ramping and
difference is more than specified in 4-38 Tracking Error Ramping Timeout are
4-35 Tracking Error for the time specified in still active.
4-36 Tracking Error Timeout.
A tracking error in closed-loop does not imply
that there is a problem with the feedback 3.6.3 4-5* Adjustable Warnings
signal! A tracking error can be the result of
torque limit for loads that are too big. Use these parameters to adjust warning limits for current,
speed, reference and feedback. Warnings that are shown
[0] * Disable
on the display can be programmed as an output or sent
[1] Warning
via serial bus.
[2] Trip
[3] Trip after Warnings are shown on display, programmed output or
stop serial bus.

Warning/Alarm 78 Tracking Error is related to the Tracking

Error Function.

3-46 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

4-53 Warning Speed High

130BA064.10
Imotor

Range: Function:
ILIM ON REF Application [Application Enter the nHIGH value. When the
(P 4-18)

IHIGH
dependent* dependant] motor speed exceeds this limit, the
display reads Speed High. The 3 3
(P 4-51) signal outputs can be
programmed to produce a status
IN RANGE
signal on terminal 27 or 29 (FC
302 only) and on relay output 01
ILOW or 02 (FC 302 only). Program the
(P 4-50)
upper signal limit of the motor
nmotor [RPM] speed, nHIGH, within the normal
nMIN nLOW REF nHIGH nMAX working range of the Adjustable
(P 4-11) (P 4-52) (P 4-53) (P 4-13) frequency drive. Refer to Figure 3.9.
Figure 3.9 Adjustable Warnings
4-54 Warning Reference Low
Range: Function:
4-50 Warning Current Low -999999.999* [Application Enter the lower reference limit.
Range: Function: dependant] When the actual reference falls
0.00 A* [Application Enter the ILOW value. When the motor below this limit, the display
dependant] indicates Ref Low. The signal
current falls below this limit, the display
outputs can be programmed to
reads Current Low. The signal outputs
produce a status signal on
can be programmed to produce a
terminal 27 or 29 (FC 302 only)
status signal on terminal 27 or 29 (FC
and on relay output 01 or 02 (FC
302 only) and on relay output 01 or 02
302 only).
(FC 302 only). Refer to Figure 3.9.

4-51 Warning Current High 4-55 Warning Reference High

Range: Function: Range: Function:

999999.999* [Application Enter the upper reference limit.
Application [Application Enter the IHIGH value. When the
dependant] When the actual reference exceeds
dependent* dependant] motor current exceeds this limit,
this limit, the display reads Ref
the display reads Current High.
High. The signal outputs can be
The signal outputs can be
programmed to produce a status
programmed to produce a status
signal on terminal 27 or 29 (FC 302
signal on terminal 27 or 29 (FC
only) and on relay output 01 or 02
302 only) and on relay output 01
(FC 302 only).
or 02 (FC 302 only). Refer to
Figure 3.9.
4-56 Warning Feedback Low
4-52 Warning Speed Low Range: Function:
Range: Function: -999999.999 [Application Enter the lower feedback
ReferenceFeed- dependant] limit. When the feedback falls
0 RPM* [Application Enter the nLOW value. When the motor
backUnit* below this limit, the display
dependant] speed exceeds this limit, the display
reads Feedb Low. The signal
reads Speed Low. The signal outputs
outputs can be programmed
can be programmed to produce a
to produce a status signal on
status signal on terminal 27 or 29 (FC
terminal 27 or 29 (FC 302
302 only) and on relay output 01 or 02
only) and on relay output 01
(FC 302 only).
or 02 (FC 302 only).

MG33MD22 - VLT® is a registered Danfoss trademark 3-47

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

4-57 Warning Feedback High 4-61 Bypass Speed From [Hz]

Range: Function: Array [4]
999999.999 [Application Enter the upper feedback Range: Function:

3 3 ReferenceFeed-
backUnit*
dependant] limit. When the feedback
exceeds this limit, the display
Size related* [ 0.0 - par. 4-14 Hz]

reads Feedb High. The signal 4-62 Bypass Speed To [RPM]

outputs can be programmed Array [4]
to produce a status signal on
Range: Function:
terminal 27 or 29 (FC 302
Application [Application Some systems call for
only) and on relay output 01
dependent* dependant] avoiding certain output
or 02 (FC 302 only).
speeds due to resonance
problems in the system.
4-58 Missing Motor Phase Function
Enter the upper limits of
Displays an alarm in the event of a missing motor phase (alarm the speeds to be avoided.
30, 31 or 32). Select disabled for no missing motor phase alarm.
It is strongly recommended to make an active setting to avoid 4-63 Bypass Speed To [Hz]
motor damage.
Array [4]
Option: Function:
Range: Function:
[0] * Disabled No alarm is displayed if a
Application [Application Some systems call for
missing motor phase
dependent* dependant] avoiding certain output
occurs.
speeds due to resonance
[1] Trip 100 ms Trips after 100 ms. Select problems in the system.
100ms for fast detection of Enter the upper limits of
missing motor phase. the speeds to be avoided.
[2] Trip 1000 ms Trips after 1000ms. Select
1000ms for slow detection
of missing motor phase.

[3] Trip 100ms 3ph

detec.

NOTE!
This parameter cannot be adjusted while the motor is
running.

3.6.4 4-6* Speed Bypass

Some systems call for avoiding certain output frequencies

or speeds due to resonance problems in the system. A
maximum of four frequency or speed ranges can be
avoided.

4-60 Bypass Speed From [RPM]

Array [4]
Range: Function:
Application [Application Some systems call for
dependent* dependant] avoiding certain output
speeds due to resonance
problems in the system.
Enter the lower limits of the
speeds to be avoided.

3-48 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.7 Parameters: 5-** Digital In/Out Digital input function Select Terminal
Start reversing [11] All
3.7.1 5-0* Digital I/O Mode Enable start forward [12] All
Enable start reverse [13] All
Parameters for configuring the input and output using
NPN and PNP.
Jog [14] All *term 29 3 3
Preset reference on [15] All
5-00 Digital I/O Mode Preset ref bit 0 [16] All
Preset ref bit 1 [17] All
Option: Function:
Preset ref bit 2 [18] All
Digital inputs and programmed digital outputs are
Freeze reference [19] All
pre-programmable for operation either in PNP or NPN
Freeze output [20] All
systems.
Speed up [21] All
[0] * PNP Action on positive directional pulses (↕). PNP systems Slow [22] All
are pulled down to GND.
Set-up select bit 0 [23] All
[1] NPN Action on negative directional pulses (↕). NPN Set-up select bit 1 [24] All
systems are pulled up to + 24V, internally in the Precise stop inverse [26] 18, 19
Adjustable frequency drive. Precise start, stop [27] 18, 19
Catch up [28] All
NOTE! Slow-down [29] All
Once this parameter has been changed, it must be Counter input [30] 29, 33
activated by performing a power cycle. Pulse input Edge Trigged [31] 29, 33
Pulse input Time Based [32] 29, 33
5-01 Terminal 27 Mode Ramp bit 0 [34] All
Option: Function: Ramp bit 1 [35] All
[0] * Input Defines terminal 27 as a digital input. Latched precise start [40] 18, 19
Latched precise stop [41] 18, 19
[1] Output Defines terminal 27 as a digital output.
inverse
External interlock [51]
5-02 Terminal 29 Mode
DigiPot Increase [55] All
Option: Function:
DigiPot Decrease [56] All
[0] * Input Defines terminal 29 as a digital input. DigiPot Clear [57] All
[1] Output Defines terminal 29 as a digital output. Digipot Hoist [58] All
Counter A (up) [60] 29, 33
This parameter is available for FC 302 only. Counter A (down) [61] 29, 33
Reset Counter A [62] All
3.7.2 Digital Inputs Counter B (up) [63] 29, 33
Counter B (down) [64] 29, 33
The digital inputs are used for selecting various functions Reset Counter B [65] All
in the Adjustable frequency drive. All digital inputs can be Mech. Brake Feedb. [70] All
set to the following functions: Mech. Brake Feedb. Inv. [71] All
PID Error Inv. [72] All
Digital input function Select Terminal
PID Reset I-part [73] All
No operation [0] All *term 32, 33
PID enable [74] All
Reset [1] All
PTC Card 1 [80] All
Coast inverse [2] All *term 27
Profidrive OFF2 [91]
Coast and reset inverse [3] All
Profidrive OFF3 [92]
Quick stop inverse [4] All
Start edge triggered [98]
DC brake inverse [5] All
Safe Option Reset [100]
Stop inverse [6] All
Start [8] All *term 18
Latched start [9] All
FC 300 standard terminals are 18, 19, 27, 29, 32 and 33.
MCB 101 terminals are X30/2, X30/3 and X30/4.
Reversing [10] All *term 19
Terminal 29 functions as an output only in FC 302.

MG33MD22 - VLT® is a registered Danfoss trademark 3-49

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

Functions dedicated to only one digital input are stated in [10] Reversing (Default Digital input 19). Change the
the associated parameter. direction of motor shaft rotation. Select Logic
‘1’ to reverse. The reversing signal only
All digital inputs can be programmed to these functions: changes the direction of rotation. It does not
3 3 activate the start function. Select both
directions in 4-10 Motor Speed Direction. The
[0] No No reaction to signals transmitted to the
function is not active in process closed-loop.
operation terminal.
[11] Start Used for start/stop and for reversing on the
[1] Reset Resets Adjustable frequency drive after a
reversing same wire. Signals on start are not allowed at
TRIP/ALARM. Not all alarms can be reset.
the same time.
[2] Coast (Default Digital input 27): Coasting stop,
[12] Enable start Disengages the counter-clockwise movement
inverse inverted input (NC). The Adjustable frequency
forward and allows for the clockwise direction.
drive leaves the motor in free mode. Logic ‘0’
=> coasting stop. [13] Enable start Disengages the clockwise movement and
reverse allows for the counter-clockwise direction.
[3] Coast and Reset and coasting stop Inverted input (NC).
reset inverse Leaves motor in free mode and resets [14] Jog (Default Digital input 29): Use to activate jog
Adjustable frequency drive. Logic ‘0’ => speed. See 3-11 Jog Speed [Hz].
coasting stop and reset. [15] Preset Shifts between external reference and preset
[4] Quick stop Inverted input (NC). Generates a stop in reference on reference. It is assumed that External/preset [1]
inverse accordance with the quick-stop ramp time set has been selected in 3-04 Reference Function.
in 3-81 Quick Stop Ramp Time. When motor Logic '0' = external reference active; logic '1'
stops, the shaft is in free mode. Logic ‘0’ => = one of the eight preset references is active.
quick stop. [16] Preset ref Preset ref. bit 0,1, and 2 enables a choice
[5] DC brake Inverted input for DC braking (NC). Stops bit 0 between one of the eight preset references
inverse motor by energizing it with a DC current for a according to the table below.
certain time period. See 2-01 DC Brake Current [17] Preset ref Same as Preset ref bit 0 [16].
to 2-03 DC Brake Cut In Speed [RPM]. The bit 1
function is only active when the value in [18] Preset ref Same as Preset ref bit 0 [16].
2-02 DC Braking Time is different from 0. bit 2
Logic ’0’ => DC braking.
Preset ref. bit 2 1 0
[6] Stop inverse Stop Inverted function. Generates a stop
Preset ref. 0 0 0 0
function when the selected terminal goes
from logical level ‘1’ to ‘0’. The stop is Preset ref. 1 0 0 1
performed according to the selected ramp Preset ref. 2 0 1 0
time (3-42 Ramp 1 Ramp Down Time, Preset ref. 3 0 1 1
3-52 Ramp 2 Ramp down Time, 3-62 Ramp 3 Preset ref. 4 1 0 0
Ramp down Time, 3-72 Ramp 4 Ramp Down Preset ref. 5 1 0 1
Time). Preset ref. 6 1 1 0
NOTE! Preset ref. 7 1 1 1
When the Adjustable frequency drive is
at the torque limit and has received a [19] Freeze Freezes the actual reference, which is now the
stop command, it may not stop by itself. ref point of enable/condition for Speed up and Slow
To ensure that the Adjustable frequency to be used. If Speed up/down is used, the speed
drive stops, configure a digital output to change always follows ramp 2 (3-51 Ramp 2 Ramp
Torque limit & stop [27] and connect this up Time and 3-52 Ramp 2 Ramp down Time) in the
digital output to a digital input that is range 0 - 3-03 Maximum Reference.
configured as coast. [20] Freeze Freezes the actual motor frequency (Hz), which is
[8] Start (Default Digital input 18): Select start for a output now the point of enable/condition for Speed up
start/stop command. Logic ‘1’ = start, logic ‘0’ and Slow to be used. If Speed up/down is used,
= stop. the speed change always follows ramp 2
[9] Latched The motor starts, if a pulse is applied for min. (3-51 Ramp 2 Ramp up Time and 3-52 Ramp 2
start 2ms. The motor stops when Stop inverse is Ramp down Time) in the range 0 - 1-23 Motor
activated or a reset command (via DI) is Frequency.
given.

3-50 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

NOTE! Precise start, stop must be triggered by a digital

When Freeze output is active, the Adjustable input and is available for terminals 18 and 19.
frequency drive cannot be stopped via a low [28] Catch up Increases reference value by percentage
‘start [8]’ signal. Stop the Adjustable (relative) set in 3-12 Catch up/slow Down Value.
frequency drive via a terminal programmed [29] Slow-
down
Reduces reference value by percentage (relative)
set in 3-12 Catch up/slow Down Value.
3 3
for Coasting inverse [2] or Coast and reset,
inverse. [30] Counter Precise stop function in 1-83 Precise Stop
input Function acts as counter stop or speed
[21] Speed Select Speed up and Slow if digital control of the
compensated counter stop with or without
up up/down speed is desired (motor potentiometer).
reset. The counter value must be set in
Activate this function by selecting either Freeze
1-84 Precise Stop Counter Value.
reference or Freeze output. When Speed up/Slow
is activated for less than 400 msec, the resulting [31] Pulse Edge-triggered pulse input counts number of
reference will be increased/decreased by 0.1%. If edge pulse flanks per sample time. This gives a higher
Speed up/down is activated for more than 400 triggered resolution at high frequencies, but is not as
msec, the resulting reference will follow the precise at lower frequencies. Use this pulse
setting in ramping up/down parameter 3-x1/ 3-x2. principle for encoders with very low resolution
(e.g., 30 ppr).
Shut down Catch up

130BB463.10
Pulse

Unchanged speed 0 0 Sample time

Reduced by %-value 1 0
Increased by %-value 0 1
Reduced by %-value 1 1
[32] Pulse time Time-based pulse input measures the duration
based between flanks. This gives a higher resolution at
[22] Slow Same as Speed up [21].
lower frequencies, but is not as precise at
[23] Set-up Select Set-up select bit 0 or Select Set-up select higher frequencies. This principle has a cut-off
select bit bit 1 to select one of the four set-ups. Set frequency which makes it unsuited for encoders
0 0-10 Active Set-up to Multi Set-up. with very low resolutions (e.g., 30 ppr) at low
[24] Set-up (Default Digital input 32): Same as Set-up select speeds.
select bit bit 0 [23].
1 Speed [rpm] Speed [rpm]

130BB462.10
[26] Precise Sends an inverted stop signal when the precise
stop inv. stop function is activated in 1-83 Precise Stop a Time[sec] b Time[sec]
Function.
Precise stop inverse function is available for
terminals 18 or 19.
[27] Precise Use when Precise ramp stop [0] is selected in
start, stop 1-83 Precise Stop Function.
a: very low encoder b: standard encoder
Precise start, stop is available for terminals 18
resolution resolution
and 19.
Precise start makes sure that the angle that the
Pulse
130BB464.10

rotor turns from standing still to reference is the Timer

Sample time
Time counter
same for each start (for same ramp time, same Time Start Read Timer:
20 timer tides
Read Timer:
20 timer tides

set-point). This is the equivalent to the precise

stop where the angle that the rotor turns from
reference to standing still is the same for each
[34] Ramp bit Enables a choice between one of the four
stop.
0 ramps available, according to the table below.
When using for 1-83 Precise Stop Function [1] or
[2]: [35] Ramp bit Same as Ramp bit 0.
The Adjustable frequency drive needs a Precise 1
Stop signal before the value of 1-84 Precise Stop
Counter Value is reached. If this is not supplied,
the Adjustable frequency drive will not stop
when the value in 1-84 Precise Stop Counter
Value is reached.

MG33MD22 - VLT® is a registered Danfoss trademark 3-51

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

Preset ramp bit 1 0 "Surface Winder," "Extended PID Speed OL"

Ramp 1 0 0 or "Extended PID Speed CL."
Ramp 2 0 1 [73] PID reset I- When enabled, resets the I-part of the
Ramp 3 1 0 part process PID controller. Equivalent to
3 3 Ramp 4 1 1 7-40 Process PID I-part Reset. Available only
if "Configuration Mode" is set to "Surface
Winder," "Extended PID Speed OL" or
[40] Latched A latched precise start only requires a pulse
"Extended PID Speed CL."
Precise Start of 3ms on T18 or T19.
[74] PID enable When enabled, enables the extended
When using for 1-83 [1] or [2]:
process PID controller. Equivalent to
When the reference is reached, the
7-50 Process PID Extended PID. Available only
Adjustable frequency drive will internally
if "Configuration Mode" is set "Extended
enable the Precise Stop signal. This means
PID Speed OL" or "Extended PID Speed CL."
that the Adjustable frequency drive will do
[80] PTC Card 1 All digital inputs can be set to PTC card 1
the Precise Stop when the counter value of
[80]. However, only one digital input must
1-84 Precise Stop Counter Value is reached.
be set to this choice.
[41] Latched Sends a latched stop signal when the
[91] Profidrive The functionality is the same as the
Precise Stop precise stop function is activated in
OFF2 according control word bit of the Profibus/
inverse 1-83 Precise Stop Function. The latched
Profinet option.
precise stop inverse function is available for
terminals 18 or 19. [92] Profidrive The functionality is the same as the
OFF3 according control word bit of the Profibus/
[51] External This function makes it possible to give an
Profinet option.
interlock external fault to the drive. This fault is
treated in the same way as an internally [98] Start edge Edge triggered start command. Keeps the
generated alarm. triggered start command alive, even if the input is
going back to low; can be used for a start
[55] DigiPot INCREASE signal to the digital potenti-
push button.
Increase ometer function described in parameter
group 3-9*. [100] Safe Option
Reset
[56] DigiPot DECREASE signal to the digital potenti-
Decrease ometer function described in parameter 5-10 Terminal 18 Digital Input
group 3-9*.
Option: Function:
[57] DigiPot Clear Clears the digital potentiometer reference
[8] * Start Functions are described under 5-1* Digital Inputs
described in parameter group 3-9*.
[60] Counter A (Terminal 29 or 33 only) Input for 5-11 Terminal 19 Digital Input
increment counting in the SLC counter.
Option: Function:
[61] Counter A (Terminal 29 or 33 only) Input for
[10] * Reversing Functions are described under 5-1* Digital
decrement counting in the SLC counter.
Inputs
[62] Reset Input for reset of counter A.
Counter A 5-12 Terminal 27 Digital Input
[63] Counter B (Terminal 29 or 33 only) Input for Option: Function:
increment counting in the SLC counter.
[2] * Coast inverse Functions are described under parameter
[64] Counter B (Terminal 29 or 33 only) Input for
group 5-1* Digital Inputs
decrement counting in the SLC counter.
[65] Reset Input for reset of counter B. 5-13 Terminal 29 Digital Input
Counter B Option: Function:
[70] Mech. Brake Brake feedback for hoisting applications: Select the function from the available digital input
Feedback Set 1-01 Motor Control Principle to [3] flux range and the additional options [60], [61], [63] and
w/ motor feedback; set 1-72 Start Function to [64]. Counters are used in Smart Logic Control
[6] Hoist mech brake Ref. functions.This parameter is available for FC 302 only.
[71] Mech. Brake Inverted brake feedback for hoisting [14] * Jog Functions are described under 5-1* Digital Inputs
Feedback inv. applications
[72] PID error When enabled, it inverts the resulting error
inverse from the process PID controller. Available
only if "Configuration Mode" is set to

3-52 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

5-14 Terminal 32 Digital Input 5-19 Terminal 37 Safe Stop

Option: Function: Option: Function:
Select the function from the available digital Choice 4 is only available when the MCB 112
input range and the additional options [60],
[61], [63] and [64]. Counters are used in
[5] PTC 1
PTC thermistor card is connected.

Coasts Adjustable frequency drive when safe

3 3
Smart Logic Control functions.
Warning stop is activated (T-37 off). When safe stop
[0] * No operation Functions are described under 5-1* Digital circuit is reestablished, the Adjustable
Inputs frequency drive will continue without manual
reset, unless a Digital Input set to PTC Card 1
5-15 Terminal 33 Digital Input
[80] is still enabled. Choice 5 is only available
Option: Function:
when the MCB 112 PTC thermistor card is
Select the function from the available digital connected.
input range and the additional options [60],
[61], [63] and [64]. Counters are used in [6] PTC 1 & This choice is used when the PTC option is
Smart Logic Control functions. Relay A gated together with a stop button through a
safety relay to T-37. Coasts Adjustable
[0] * No operation Functions are described under 5-1* Digital
frequency drive when safe stop is activated.
Inputs
Manual reset from LCP, digital input or serial
5-16 Terminal X30/2 Digital Input communication bus. Choice 6 is only available
Option: Function: when the MCB 112 PTC thermistor card is
connected.
[0] * No operation This parameter is active when option module
MCB101 is installed in the Adjustable [7] PTC 1 & This choice is used when the PTC option is
frequency drive. Functions are described Relay W gated together with a stop button through a
under 5-1* Digital Inputs safety relay to T-37. Coasts Adjustable
frequency drive when safe stop is activated
5-17 Terminal X30/3 Digital Input (T-37 off). When safe stop circuit is reestab-
Option: Function: lished, the Adjustable frequency drive will
[0] * No operation This parameter is active when option module continue without manual reset, unless a
MCB101 is installed in the Adjustable Digital Input set to PTC Card 1 [80] is (still)
frequency drive. Functions are described enabled. Choice 7 is only available when the
under 5-1* Digital Inputs MCB 112 PTC thermistor card is connected.

5-18 Terminal X30/4 Digital Input [8] PTC 1 & This choice makes it possible to use a
Relay A/W combination of alarm and warning. Choice 8
Option: Function:
is only available when the MCB 112 PTC
[0] * No operation This parameter is active when option module thermistor card is connected.
MCB101 is installed in the Adjustable
frequency drive. Functions are described [9] PTC 1 & This choice makes it possible to use a
under 5-1* Digital Inputs Relay W/A combination of alarm and warning. Choice 9
is only available when the MCB 112 PTC
5-19 Terminal 37 Safe Stop thermistor card is connected.
Option: Function:
Choices 4–9 are only available when the MCB 112 PTC
[1] Safe Stop Coasts Adjustable frequency drive when safe
thermistor card is connected.
* Alarm stop is activated. Manual reset from LCP,
digital input or serial communication bus.

[3] Safe Stop Coasts Adjustable frequency drive when safe

Warning stop is activated (T-37 off). When safe stop
circuit is reestablished, the Adjustable
frequency drive will continue without manual
reset.

[4] PTC 1 Alarm Coasts Adjustable frequency drive when safe

stop is activated. Manual reset from LCP,
digital input or serial communication bus.

MG33MD22 - VLT® is a registered Danfoss trademark 3-53

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

NOTE! 5-23 Terminal X46/7 Digital Input

When Auto Reset/Warning is selected the Adjustable Option: Function:
frequency drive opens up for automatic restart. [0] * No operation This parameter is active when option

3 3 Overview of functions, alarms and warnings

moduleMCB 113 is installed in the Adjustable
frequency drive. Functions are described
under 5-1* Digital Inputs
Function No. PTC Relay
No Function [0] - - 5-24 Terminal X46/9 Digital Input
Safe Stop Alarm [1]* - Safe Stop [A68] Option: Function:
Safe Stop Warning [3] - Safe Stop [W68] [0] * No operation This parameter is active when option module
MCB 113 is installed in the Adjustable
PTC 1 Alarm [4] PTC 1 Safe Stop - frequency drive. Functions are described
[A71] under 5-1* Digital Inputs
PTC 1 Warning [5] PTC 1 Safe Stop -
[W71] 5-25 Terminal X46/11 Digital Input
PTC 1 & Relay A [6] PTC 1 Safe Stop Safe Stop [A68] Option: Function:
[A71] [0] * No operation This parameter is active when option
PTC 1 & Relay W [7] PTC 1 Safe Stop Safe Stop [W68] moduleMCB 113 is installed in the Adjustable
[W71] frequency drive. Functions are described
PTC 1 & Relay A/W [8] PTC 1 Safe Stop Safe Stop [W68] under 5-1* Digital Inputs
[A71]
5-26 Terminal X46/13 Digital Input
PTC 1 & Relay W/A [9] PTC 1 Safe Stop Safe Stop [A68]
[W71] Option: Function:
[0] * No operation This parameter is active when option module
W means warning, and A means alarm. For further information, see
MCB 113 is installed in the Adjustable
Alarms and Warnings in section Troubleshooting in the Design Guide
frequency drive. Functions are described
or in the Instruction Manual.
under 5-1* Digital Inputs

A dangerous failure related to the safe stop will give alarm:

Dangerous Failure [A72]. 3.7.3 5-3* Digital Outputs
Please refer to in .
The 2 solid-state digital outputs are common for terminals
5-20 Terminal X46/1 Digital Input 27 and 29. Set the I/O function for terminal 27 in
Option: Function: 5-01 Terminal 27 Mode, and set the I/O function for
[0] * No operation This parameter is active when option module terminal 29 in 5-02 Terminal 29 Mode.
MCB 113 is installed in the Adjustable
frequency drive. Functions are described NOTE!
under 5-1* Digital Inputs These parameters cannot be adjusted while the motor is
running.
5-21 Terminal X46/3 Digital Input
Option: Function:
[0] No operation Default for all digital outputs and relay
[0] * No operation This parameter is active when option
outputs
moduleMCB 113 is installed in the Adjustable
[1] Control ready The control card is ready. For example,
frequency drive. Functions are described
Feedback from a Adjustable frequency
under 5-1* Digital Inputs
drive where the control is supplied by an
5-22 Terminal X46/5 Digital Input external 24 V (MCB 107) and the main
power to the unit is not detected.
Option: Function:
[2] Drive ready The Adjustable frequency drive is ready
[0] * No operation This parameter is active when option
for operation and applies a supply signal
moduleMCB 113 is installed in the Adjustable
on the control board.
frequency drive. Functions are described
[3] Drive ready / The Adjustable frequency drive is ready
under 5-1* Digital Inputs
remote control for operation and is in [Auto on] mode.

3-54 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

[4] Enable / no Ready for operation. No start or stop [24] Ready, voltage Adjustable frequency drive is ready for
warning command is been given (start/disable). OK operation and the AC line voltage is
No warnings are active. within the specified voltage range (see
[5] VLT running Motor is running and shaft torque is General Specifications section in the

[6] Running / no
present.
Output speed is higher than the speed [25] Reverse
Design Guide).
Reversing. Logic ‘1’ when CW rotation of
3 3
warning set in 1-81 Min Speed for Function at Stop the motor. Logic ‘0’ when CCW rotation
[RPM]. The motor is running and there are of the motor. If the motor is not rotating,
no warnings. the output will follow the reference.
[7] Run in Motor is running within the programmed [26] Bus OK Active communication (no timeout) via
range/no current and speed ranges set in the serial communication port.
warning 4-50 Warning Current Low to 4-53 Warning [27] Torque limit Use in performing a coasting stop and in
Speed High. There are no warnings. and stop torque limit condition. If the Adjustable
[8] Run on Motor runs at reference speed. No frequency drive has received a stop signal
reference / no warnings. and is at the torque limit, the signal is
warning Logic ‘0’.
[9] Alarm An alarm activates the output. There are [28] Brake, no brake Brake is active and there are no warnings.
no warnings. warning
[10] Alarm or An alarm or a warning activates the [29] Brake ready, no Brake is ready for operation and there are
warning output. fault no faults.
[11] At torque limit The torque limit set in 4-16 Torque Limit [30] Brake fault Output is Logic ‘1’ when the brake IGBT is
Motor Mode or 4-17 Torque Limit Generator (IGBT) short-circuited. Use this function to
Mode has been exceeded. protect the Adjustable frequency drive if
[12] Out of current The motor current is outside the range there is a fault on the brake modules. Use
range set in 4-18 Current Limit. the output/relay to cut out the AC line
[13] Below current, Motor current is lower than set in voltage from the Adjustable frequency
low 4-50 Warning Current Low. drive.
[14] Above current, Motor current is higher than set in [31] Relay 123 The relay is activated when Control Word
high 4-51 Warning Current High. [0] is selected in parameter group 8-**.
[15] Out of speed Output frequency is outside the [32] Mechanical Enables control of an external mechanical
range frequency ranges set in 4-52 Warning brake control brake, see description in the section
Speed Low and 4-53 Warning Speed High. Control of Mechanical Brake, and
[16] Below speed, Output speed is lower than the setting in parameter group 2-2*
low 4-52 Warning Speed Low. [33] Safe stop Indicates that the safe stop on terminal
[17] Above speed, Output speed is higher than the setting activated (FC 37 has been activated.
high in 4-53 Warning Speed High. 302 only)
[18] Out of Feedback is outside the range set in [40] Out of ref Active when the actual speed is outside
feedback range 4-56 Warning Feedback Low and range settings in 4-52 Warning Speed Low to
4-57 Warning Feedback High. 4-55 Warning Reference High.
[19] Below Feedback is below the limit set in [41] Below Active when actual speed is below speed
feedback low 4-56 Warning Feedback Low. reference low reference setting.
[20] Above Feedback is above the limit set in [42] Above Active when actual speed is above speed
feedback high 4-57 Warning Feedback High. reference high reference setting
[21] Thermal The thermal warning turns on when the [43] Extended PID
warning temperature exceeds the limit in the Limit
motor, the Adjustable frequency drive, [45] Bus Ctrl Controls output via bus. The state of the
the brake resistor, or the thermistor. output is set in 5-90 Digital & Relay Bus
[22] Ready, no Adjustable frequency drive is ready for Control. The output state is retained in
thermal operation and there is no over- the event of bus timeout.
warning temperature warning. [46] Bus Ctrl On at Controls output via bus. The state of the
[23] Remote, ready, Adjustable frequency drive is ready for timeout output is set in 5-90 Digital & Relay Bus
no thermal operation and is in [Auto on] mode. Control. In the event of a bus timeout,
warning There is no over-temperature warning. the output state is set high (On).

MG33MD22 - VLT® is a registered Danfoss trademark 3-55

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

[47] Bus Ctrl Off at Controls output via bus. The state of the the Smart Logic Action [33] Set dig. out. A
timeout output is set in 5-90 Digital & Relay Bus low is executed.
Control. In the event of a bus timeout, [82] SL Digital See 13-52 SL Controller Action. The input
the output state is set low (Off). Output C will go high whenever the Smart Logic
3 3 [51] MCO controlled Active when a MCO 302 or MCO 305 is
connected. The output is controlled from
Action [40] Set dig. out. A high is
executed. The input will go low whenever
option. the Smart Logic Action [34] Set dig. out. A
[55] Pulse output low is executed.
[60] Comparator 0 See parameter group 13-1*. If Comparator [83] SL Digital See 13-52 SL Controller Action. The input
0 is evaluated as TRUE, the output will go Output D will go high whenever the Smart Logic
high. Otherwise, it will be low. Action [41] Set dig. out. A high is
[61] Comparator 1 See parameter group 13-1*. If Comparator executed. The input will go low whenever
1 is evaluated as TRUE, the output will go the Smart Logic Action [35] Set dig. out. A
high. Otherwise, it will be low. low is executed.
[62] Comparator 2 See parameter group 13-1*. If Comparator [84] SL Digital See 13-52 SL Controller Action. The input
2 is evaluated as TRUE, the output will go Output E will go high whenever the Smart Logic
high. Otherwise, it will be low. Action [42] Set dig. out. A high is
[63] Comparator 3 See parameter group 13-1*. If Comparator executed. The input will go low whenever
3 is evaluated as TRUE, the output will go the Smart Logic Action [36] Set dig. out. A
high. Otherwise, it will be low. low is executed.
[64] Comparator 4 See parameter group 13-1*. If Comparator [85] SL Digital See 13-52 SL Controller Action. The input
4 is evaluated as TRUE, the output will go Output F will go high whenever the Smart Logic
high. Otherwise, it will be low. Action [43] Set dig. out. A high is
[65] Comparator 5 See parameter group 13-1*. If Comparator executed. The input will go low whenever
5 is evaluated as TRUE, the output will go the Smart Logic Action [37] Set dig. out. A
high. Otherwise, it will be low. low is executed.
[70] Logic Rule 0 See parameter group 13-4*. If Logic Rule [120] Local reference Output is high when 3-13 Reference Site =
0 is evaluated as TRUE, the output will go active [2] Local or when 3-13 Reference Site = [0]
high. Otherwise, it will be low. Linked to hand auto at the same time as
[71] Logic Rule 1 See parameter group 13-4*. If Logic Rule the LCP is in [Hand on] mode.
1 is evaluated as TRUE, the output will go
Reference site Local Remote
high. Otherwise, it will be low.
set in referenc reference
[72] Logic Rule 2 See parameter group 13-4*. If Logic Rule
3-13 Reference e active
2 is evaluated as TRUE, the output will go
Site active [121]
high. Otherwise, it will be low.
[120]
[73] Logic Rule 3 See parameter group 13-4*. If Logic Rule Reference site: 1 0
3 is evaluated as TRUE, the output will go Local
high. Otherwise, it will be low. 3-13 Reference Site
[74] Logic Rule 4 See parameter group 13-4*. If Logic Rule [2]
4 is evaluated as TRUE, the output will go Reference site: 0 1
high. Otherwise, it will be low. Remote
[75] Logic Rule 5 See parameter group 13-4*. If Logic Rule 3-13 Reference Site
5 is evaluated as TRUE, the output will go [1]
high. Otherwise, it will be low. Reference site:
[80] SL Digital See 13-52 SL Controller Action. The output Linked to Hand/
Output A will go high whenever the Smart Logic Auto
Action [38] Set dig. out. A high is Hand 1 0
executed. The output will go low
Hand -> off 1 0
whenever the Smart Logic Action [32] Set
Auto -> off 0 0
dig. out. A low is executed.
Auto 0 1
[81] SL Digital See 13-52 SL Controller Action. The input
Output B will go high whenever the Smart Logic
Action [39] Set dig. out. A high is
executed. The input will go low whenever

3-56 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

[121] Remote Output is high when 3-13 Reference Site = 5-31 Terminal 29 Digital Output
reference Remote [1] or Linked to hand/auto [0]
Option: Function:
active while the LCP is in [Auto on] mode. See
[0] * No operation Functions are described under 5-3* Digital
above.
[122] No alarm Output is high when no alarm is present.
[123] Start command Output is high when there is an active
Outputs
This parameter only applies to FC 302 3 3
active Start command (i.e., via digital input bus 5-32 Term X30/6 Digi Out (MCB 101)
connection or [Hand on] or [Auto on]), Option: Function:
and no Stop or Start command is active.
[0] * No operation This parameter is active when
[124] Running Output is high when the Adjustable
option module MCB 101 is
reverse frequency drive is running counter
mounted in the Adjustable
clockwise (the logical product of the
frequency drive. Functions are
status bits ‘running’ AND ‘reverse’).
described under 5-3* Digital
[125] Drive in hand Output is high when the Adjustable Outputs
mode frequency drive is in [Hand on] mode (as
indicated by the LED light above [Hand [1] Control ready
on]). [2] Drive ready
[126] Drive in auto Output is high when the Adjustable [3] Drive rdy/rem ctrl
mode frequency drive is in [Hand on] mode (as [4] Enable / no warning
indicated by the LED above [Auto on]). [5] Running
[151] ATEX ETR cur. Selectable if 1-90 Motor Thermal Protection [6] Running / no warning
alarm is set to [20] or [21]. If the alarm 164 [7] Run in range/no warn
ATEX ETR cur.lim.alarm is active, the [8] Run on ref/no warn
output will be 1. [9] Alarm
[152] ATEX ETR freq. Selectable if 1-90 Motor Thermal Protection [10] Alarm or warning
alarm is set to [20] or [21]. If the alarm 166 [11] At torque limit
ATEX ETR freq.lim.alarm is active, the [12] Out of current range
output will be 1. [13] Below current, low
[153] ATEX ETR cur. Selectable if1-90 Motor Thermal Protection [14] Above current, high
warning is set to [20] or [21]. If the alarm 163 [15] Out of speed range
ATEX ETR cur.lim.warning is active, the
[16] Below speed, low
output will be 1.
[17] Above speed, high
[154] ATEX ETR freq. Selectable if 1-90 Motor Thermal Protection
[18] Out of feedb. range
warning is set to [20] or [21]. If the warning 165
[19] Below feedback, low
ATEX ETR freq.lim.warning is active, the
[20] Above feedback, high
output will be 1.
[21] Thermal warning
[188] AHF Capacitor The capacitors will be turned on at 20%
[22] Ready,no thermal W
Connect (hysteresis of 50% gives an interval of
[23] Remote,ready,no TW
10%–30%). The capacitors will be discon-
nected below 10%. The off delay is 10 s [24] Ready, Voltage OK
and will restart if the nominal power goes [25] Reverse
above 10% during the delay. 5-80 AHF [26] Bus OK
Cap Reconnect Delay is used to guarantee [27] Torque limit & stop
a minimum off-time for the capacitors. [28] Brake, no brake war
[189] External fan The internal logics for the internal fan [29] Brake ready, no fault
control control is transferred to this output to [30] Brake fault (IGBT)
make it possible to control an external [31] Relay 123
fan (relevant for HP duct cooling). [32] Mech brake ctrl
[33] Safe stop active
5-30 Terminal 27 Digital Output
[38] Motor feedback error
Option: Function:
[39] Tracking error
[0] * No operation Functions are described under 5-3* Digital [40] Out of ref range
Outputs
[41] Below reference, low
[42] Above ref, high

MG33MD22 - VLT® is a registered Danfoss trademark 3-57

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

5-32 Term X30/6 Digi Out (MCB 101) 5-33 Term X30/7 Digi Out (MCB 101)
Option: Function: Option: Function:
[43] Extended PID Limit [0] * No operation This parameter is active when

3 3 [45]
[46]
Bus ctrl.
Bus ctrl, 1 if timeout
option module MCB 101 is
mounted in the Adjustable
[47] Bus ctrl, 0 if timeout frequency drive. Functions are
[51] MCO controlled described under 5-3* Digital
[55] Pulse output Outputs

[60] Comparator 0 [1] Control ready

[61] Comparator 1 [2] Drive ready
[62] Comparator 2 [3] Drive rdy/rem ctrl
[63] Comparator 3 [4] Enable / no warning
[64] Comparator 4 [5] Running
[65] Comparator 5 [6] Running / no warning
[70] Logic rule 0 [7] Run in range/no warn
[71] Logic rule 1 [8] Run on ref/no warn
[72] Logic rule 2 [9] Alarm
[73] Logic rule 3 [10] Alarm or warning
[74] Logic rule 4 [11] At torque limit
[75] Logic rule 5 [12] Out of current range
[80] SL digital output A [13] Below current, low
[81] SL digital output B [14] Above current, high
[82] SL digital output C [15] Out of speed range
[83] SL digital output D [16] Below speed, low
[84] SL digital output E [17] Above speed, high
[85] SL digital output F [18] Out of feedb. range
[120] Local ref active [19] Below feedback, low
[121] Remote ref active [20] Above feedback, high
[122] No alarm [21] Thermal warning
[123] Start command activ [22] Ready,no thermal W
[124] Running reverse [23] Remote,ready,no TW
[125] Drive in hand mode [24] Ready, Voltage OK
[126] Drive in auto mode [25] Reverse
[151] ATEX ETR cur. alarm [26] Bus OK
[152] ATEX ETR freq. alarm [27] Torque limit & stop
[153] ATEX ETR cur. warning [28] Brake, no brake war
[154] ATEX ETR freq. warning [29] Brake ready, no fault
[188] AHF Capacitor Connect [30] Brake fault (IGBT)
[189] External Fan Control [31] Relay 123
[190] Safe Function active [32] Mech brake ctrl
[191] Safe Opt. Reset req. [33] Safe stop active
[192] RS Flipflop 0 [39] Tracking error
[193] RS Flipflop 1 [40] Out of ref range
[194] RS Flipflop 2 [41] Below reference, low
[195] RS Flipflop 3 [42] Above ref, high
[196] RS Flipflop 4 [43] Extended PID Limit
[197] RS Flipflop 5 [45] Bus ctrl.
[198] RS Flipflop 6 [46] Bus ctrl, 1 if timeout
[199] RS Flipflop 7 [47] Bus ctrl, 0 if timeout
[51] MCO controlled
[60] Comparator 0

3-58 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

5-33 Term X30/7 Digi Out (MCB 101) 5-40 Function Relay
Option: Function: Array [9]
[61] Comparator 1 (Relay 1 [0], Relay 2 [1], Relay 3 [2] (MCB 113), Relay 4 [3] (MCB
113), Relay 5 [4] (MCB 113), Relay 6 [5] (MCB 113), Relay 7 [6]
[62]
[63]
Comparator 2
Comparator 3 (MCB 105), Relay 8 [7] (MCB 105), Relay 9 [8] (MCB 105)) 3 3
[64] Comparator 4 Option: Function:
[65] Comparator 5 [0] * No operation All digital and relay outputs are
[70] Logic rule 0 default set to “No Operation”.
[71] Logic rule 1 [1] Control ready The control card is ready. For
[72] Logic rule 2 example, Feedback from a drive
[73] Logic rule 3 where the control is supplied by an
[74] Logic rule 4 external 24 V (MCB 107) and the
[75] Logic rule 5 main power to drive is not detected.
[80] SL digital output A
[2] Drive ready Drive is ready to operate. Line power
[81] SL digital output B and control supplies are OK.
[82] SL digital output C
[3] Drive rdy/rem ctrl The Adjustable frequency drive is
[83] SL digital output D
ready for operation and is in auto on
[84] SL digital output E
mode
[85] SL digital output F
[120] Local ref active [4] Enable / no warning Ready for operation. No start or stop
[121] Remote ref active commands have been applied (start/
[122] No alarm disable). No warnings are active.

[123] Start command activ [5] Running Motor is running, and shaft torque
[124] Running reverse present.
[125] Drive in hand mode [6] Running / no Output speed is higher than the
[126] Drive in auto mode warning speed set in 1-81 Min Speed for
[151] ATEX ETR cur. alarm Function at Stop [RPM] Min Speed for
[152] ATEX ETR freq. alarm Function at Stop [RPM]. The motor is
[153] ATEX ETR cur. warning running and no warnings.
[154] ATEX ETR freq. warning
[7] Run in range/no Motor is running within the
[189] External Fan Control warn programmed current and speed
[190] Safe Function active ranges set in 4-50 Warning Current
[191] Safe Opt. Reset req. Low and 4-53 Warning Speed High.
[192] RS Flipflop 0 No warnings.
[193] RS Flipflop 1
[8] Run on ref/no warn Motor runs at reference speed. No
[194] RS Flipflop 2
warnings.
[195] RS Flipflop 3
[196] RS Flipflop 4 [9] Alarm An alarm activates the output. No
warnings
[197] RS Flipflop 5
[198] RS Flipflop 6 [10] Alarm or warning An alarm or a warning activates the
[199] RS Flipflop 7 output.

[11] At torque limit The torque limit set in 4-16 Torque

3.7.4 5-4* Relays Limit Motor Mode or 4-17 Torque
Limit Generator Mode has been
Parameters for configuring the timing and the output exceeded.
functions for the relays. [12] Out of current The motor current is outside the
range range set in 4-18 Current Limit.

[13] Below current, low Motor current is lower than set in

4-50 Warning Current Low.

MG33MD22 - VLT® is a registered Danfoss trademark 3-59

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

5-40 Function Relay 5-40 Function Relay

Array [9] Array [9]
(Relay 1 [0], Relay 2 [1], Relay 3 [2] (MCB 113), Relay 4 [3] (MCB (Relay 1 [0], Relay 2 [1], Relay 3 [2] (MCB 113), Relay 4 [3] (MCB
113), Relay 5 [4] (MCB 113), Relay 6 [5] (MCB 113), Relay 7 [6] 113), Relay 5 [4] (MCB 113), Relay 6 [5] (MCB 113), Relay 7 [6]
3 3 (MCB 105), Relay 8 [7] (MCB 105), Relay 9 [8] (MCB 105)) (MCB 105), Relay 8 [7] (MCB 105), Relay 9 [8] (MCB 105))
Option: Function: Option: Function:
[14] Above current, high Motor current is higher than set in [27] Torque limit & stop Use in performing a coasted stop
4-51 Warning Current High. and Adjustable frequency drive in
torque limit condition. If the
[15] Out of speed range Output speed/frequency is outside
Adjustable frequency drive has
the frequency ranges set in
received a stop signal and is in
4-52 Warning Speed Low and
torque limit, the signal is Logic ‘0’.
4-53 Warning Speed High.
[28] Brake, no brake war Brake is active and there are no
[16] Below speed, low Output speed is lower than the
warnings.
setting in 4-52 Warning Speed Low
[29] Brake ready, no Brake is ready for operation and
[17] Above speed, high Output speed is higher than the
fault there are no faults.
setting in 4-53 Warning Speed High.
[30] Brake fault (IGBT) Output is Logic ‘1’ when the brake
[18] Out of feedb. range Feedback is outside the range set in
IGBT is short-circuited. Use this
4-56 Warning Feedback Low and
function to protect the Adjustable
4-57 Warning Feedback High.
frequency drive if there is a fault on
[19] Below feedback, low Feedback is below the limit set in the brake module. Use the digital
4-56 Warning Feedback Low. output/relay to cut out the AC line
[20] Above feedback, Feedback is above the limit set in voltage from the Adjustable
high 4-57 Warning Feedback High. frequency drive.

[21] Thermal warning Thermal warning turns on when the [31] Relay 123 Digital output/relay is activated
temperature exceeds the limit either when Control Word [0] is selected in
in motor, Adjustable frequency drive, parameter group 8-**.
brake resistor, or connected [32] Mech brake ctrl Selection of mechanical brake
thermistor. control. When selected parameters in
[22] Ready,no thermal W Adjustable frequency drive is ready parameter group 2-2* are active. The
for operation and there is no output must be reinforced to carry
overtemperature warning. the current for the coil in the brake.
Usually solved by connecting an
[23] Remote,ready,no TW Adjustable frequency drive is ready
external relay to the selected digital
for operation and is in auto on
output.
mode. There is no overtemperature
warning. [33] Safe stop active (FC 302 only) Indicates that the safe
stop on terminal 37 has been
[24] Ready, Voltage OK Adjustable frequency drive is ready
activated.
for operation and the AC line
voltage is within the specified [36] Control word bit 11 Activate relay 1 by control word
voltage range (see General Specifi- from the serial communication bus.
cations section in Design Guide). No other functional impact in the
Adjustable frequency drive. Typical
[25] Reverse Logic ‘1’ when CW rotation of the
application: controlling auxiliary
motor. Logic ‘0’ when CCW rotation
device from the serial communi-
of the motor. If the motor is not
cation bus. The function is valid
rotating, the output will follow the
when FC profile [0] in 8-10 Control
reference.
Word Profile is selected.
[26] Bus OK Active communication (no timeout)
[37] Control word bit 12 Activate relay 2 FC 302 only) by
via the serial communication port.
control word from serial communi-
cation bus. No other functional

3-60 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

5-40 Function Relay 5-40 Function Relay

Array [9] Array [9]
(Relay 1 [0], Relay 2 [1], Relay 3 [2] (MCB 113), Relay 4 [3] (MCB (Relay 1 [0], Relay 2 [1], Relay 3 [2] (MCB 113), Relay 4 [3] (MCB
113), Relay 5 [4] (MCB 113), Relay 6 [5] (MCB 113), Relay 7 [6] 113), Relay 5 [4] (MCB 113), Relay 6 [5] (MCB 113), Relay 7 [6]
(MCB 105), Relay 8 [7] (MCB 105), Relay 9 [8] (MCB 105)) (MCB 105), Relay 8 [7] (MCB 105), Relay 9 [8] (MCB 105)) 3 3
Option: Function: Option: Function:
impact in the Adjustable frequency [60] Comparator 0 See parameter group 13-1* (Smart
drive. Typical application: controlling Logic Control). If Comparator 0 in
auxiliary device from the serial SLC is TRUE, the output will go high.
communication bus. The function is Otherwise, it will be low.
valid when FC profile [0] in
[61] Comparator 1 See parameter group 13-1* (Smart
8-10 Control Word Profile is selected.
Logic Control). If Comparator 1 in
[38] Motor feedback Failure in the speed feedback loop SLC is TRUE, the output will go high.
error from motor running in closed-loop. Otherwise, it will be low.
The output can eventually be used
[62] Comparator 2 See parameter group 13-1* (Smart
to prepare switching the drive in
Logic Control). If Comparator 2 in
open-loop in emergency case.
SLC is TRUE, the output will go high.
[39] Tracking error When the difference between Otherwise, it will be low.
calculated speed and actual speed in
[63] Comparator 3 See parameter group 13-1* (Smart
4-35 Tracking Error is larger than
Logic Control). If Comparator 3 in
selected the digital output/relay is
SLC is TRUE, the output will go high.
active.
Otherwise, it will be low.
[40] Out of ref range Active when the actual speed is
[64] Comparator 4 See parameter group 13-1* (Smart
outside settings in 4-52 Warning
Logic Control). If Comparator 4 in
Speed Low to 4-55 Warning Reference
SLC is TRUE, the output will go high.
High.
Otherwise, it will be low.
[41] Below reference, Active when actual speed is below
[65] Comparator 5 See parameter group 13-1* (Smart
low speed reference setting.
Logic Control). If Comparator 5 in
[42] Above ref, high Active when actual speed is above SLC is TRUE, the output will go high.
speed reference setting. Otherwise, it will be low.

[43] Extended PID Limit [70] Logic rule 0 See parameter group 13-4*(Smart
[45] Bus ctrl. Controls digital output/relay via bus. Logic Control). If Logic Rule 0 in SLC
The state of the output is set in is TRUE, the output will go high.
5-90 Digital & Relay Bus Control. The Otherwise, it will be low.
output state is retained in the event
[71] Logic rule 1 See parameter group 13-4*(Smart
of bus timeout.
Logic Control). If Logic Rule 1 in SLC
[46] Bus ctrl, 1 if timeout Controls output via bus. The state of is TRUE, the output will go high.
the output is set in 5-90 Digital & Otherwise, it will be low.
Relay Bus Control. In the event of a
[72] Logic rule 2 See parameter group 13-4*(Smart
bus timeout, the output state is set
Logic Control). If Logic Rule 2 in SLC
high (On).
is TRUE, the output will go high.
[47] Bus ctrl, 0 if timeout Controls output via bus. The state of Otherwise, it will be low.
the output is set in 5-90 Digital &
[73] Logic rule 3 See parameter group 13-4*(Smart
Relay Bus Control. In the event of a
Logic Control). If Logic Rule 3 in SLC
bus timeout, the output state is set
is TRUE, the output will go high.
low (Off).
Otherwise, it will be low.
[51] MCO controlled Active when a MCO 302 or MCO 305
[74] Logic rule 4 See parameter group 13-4*(Smart
is connected. The output is
Logic Control). If Logic Rule 4 in SLC
controlled from option.
is TRUE, the output will go high.
Otherwise, it will be low.

MG33MD22 - VLT® is a registered Danfoss trademark 3-61

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

5-40 Function Relay 5-40 Function Relay

Array [9] Array [9]
(Relay 1 [0], Relay 2 [1], Relay 3 [2] (MCB 113), Relay 4 [3] (MCB (Relay 1 [0], Relay 2 [1], Relay 3 [2] (MCB 113), Relay 4 [3] (MCB
113), Relay 5 [4] (MCB 113), Relay 6 [5] (MCB 113), Relay 7 [6] 113), Relay 5 [4] (MCB 113), Relay 6 [5] (MCB 113), Relay 7 [6]
3 3 (MCB 105), Relay 8 [7] (MCB 105), Relay 9 [8] (MCB 105)) (MCB 105), Relay 8 [7] (MCB 105), Relay 9 [8] (MCB 105))
Option: Function: Option: Function:
[75] Logic rule 5 See parameter group 13-4*(Smart Reference site Local Remote
Logic Control). If Logic Rule 5 in SLC set in referen reference
is TRUE, the output will go high. 3-13 Reference ce active
Otherwise, it will be low. Site active [121]
[120]
[80] SL digital output A See 13-52 SL Controller Action. Output
A is low on Smart Logic Action [32]. Reference site: 1 0
Output A is high on Smart Logic Local
Action [38]. 3-13 Reference
Site [2]
[81] SL digital output B See 13-52 SL Controller Action. Output
Reference site: 0 1
B is low on Smart Logic Action [33].
Remote
Output B is high on Smart Logic
3-13 Reference
Action [39].
Site [1]
[82] SL digital output C See 13-52 SL Controller Action. Output Reference site:
C is low on Smart Logic Action [34]. Linked to Hand/
Output C is high on Smart Logic Auto
Action [40]. Hand 1 0
[83] SL digital output D See 13-52 SL Controller Action. Output Hand -> off 1 0
D is low on Smart Logic Action [35]. Auto -> off 0 0
Output D is high on Smart Logic Auto 0 1
Action [41]

[84] SL digital output E See 13-52 SL Controller Action. Output [121] Remote ref active Output is high when 3-13 Reference
E is low on Smart Logic Action [36]. Site = Remote [1] or Linked to hand/
Output E is high on Smart Logic auto [0] while the LCP is in [Auto on]
Action [42]. mode. See above.

[85] SL digital output F See 13-52 SL Controller Action. Output [122] No alarm Output is high when no alarm is
F is low on Smart Logic Action [37]. present.
Output F is high on Smart Logic [123] Start command Output is high when the Start
Action [43]. activ command high (i.e., via digital input,
[120] Local ref active Output is high when 3-13 Reference bus connection or [Hand on] or
Site = [2] Local or when [Auto on]), and a Stop has been last
3-13 Reference Site = [0] Linked to command.
hand auto at the same time as the [124] Running reverse Output is high when the Adjustable
LCP is in [Hand on] mode. frequency drive is running counter
clockwise (the logical product of the
status bits ‘running’ AND ‘reverse’).

[125] Drive in hand mode Output is high when the Adjustable

frequency drive is in [Hand on]
mode (as indicated by the LED
above [Hand on]).

[126] Drive in auto mode Output is high when the Adjustable

frequency drive is in ‘Auto’ mode (as
indicated by LED on above [Auto
on]).

3-62 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

5-40 Function Relay

130BA171.10
Selected
Array [9] Event
(Relay 1 [0], Relay 2 [1], Relay 3 [2] (MCB 113), Relay 4 [3] (MCB
113), Relay 5 [4] (MCB 113), Relay 6 [5] (MCB 113), Relay 7 [6]
3 3
Relay
output
(MCB 105), Relay 8 [7] (MCB 105), Relay 9 [8] (MCB 105))
Option: Function: On Delay Off Delay
P 5-41 P 5-42
[151] ATEX ETR cur. alarm Selectable if 1-90 Motor Thermal
Protection is set to [20] or [21]. If the
Selected
alarm 164 ATEX ETR cur.lim.alarm is Event
active, the output will be 1.
Relay
[152] ATEX ETR freq. Selectable if 1-90 Motor Thermal output
alarm Protection is set to [20] or [21]. If the
alarm 166 ATEX ETR freq.lim.alarm is On Delay
P 5-41
active, the output will be 1.

[153] ATEX ETR cur. Selectable if 1-90 Motor Thermal

warning Protection is set to [20] or [21]]. If the 5-42 Off Delay, Relay
alarm 163 ATEX ETR cur.lim.warning Array [9] (Relay 1 [0], Relay 2 [1], Relay 3 [2], Relay 4 [3], Relay 5
is active, the output will be 1. [4], Relay 6 [5], Relay 7 [6], Relay 8 [7], Relay 9 [8])
[154] ATEX ETR freq. Selectable if 1-90 Motor Thermal Range: Function:
warning Protection is set to [20] or [21]. If the 0.01 s* [0.01 - 600.00 s] Enter the delay of the relay cut-out
warning 165 ATEX ETR time. Select one of available
freq.lim.warning is active, the output mechanical relays and MCB 105 in an
will be 1. array function. See 5-40 Function Relay.
[188] AHF Capacitor

130BA172.10
Connect
[189] External Fan Control The internal logics for the internal
Selected
fan control is transferred to this Event
output to make it possible to control
an external fan (relevant for HP duct
Relay
cooling).
output
[192] RS Flipflop 0
[193] RS Flipflop 1 On Delay Off Delay
P 5-41 P 5-42
[194] RS Flipflop 2
[195] RS Flipflop 3
[196] RS Flipflop 4 If the selected event condition changes before the on or
[197] RS Flipflop 5 off delay timer expires, the relay output is unaffected.
[198] RS Flipflop 6
[199] RS Flipflop 7 3.7.5 5-5* Pulse Input
5-41 On Delay, Relay
The pulse input parameters are used to define an
Array [9], (Relay 1 [0], Relay 2 [1], Relay 3 [2], Relay 4 [3], Relay 5 appropriate window for the impulse reference area by
[4], Relay 6 [5], Relay 7 [6], Relay 8 [7], Relay 9 [8]) configuring the scaling and filter settings for the pulse
Range: Function: inputs. Input terminals 29 or 33 act as frequency reference
0.01 s* [0.01 - 600.00 s] Enter the delay of the relay cut-in inputs. Set terminal 29 (5-13 Terminal 29 Digital Input) or
time. Select one of available terminal 33 (5-15 Terminal 33 Digital Input) to Pulse input
mechanical relays and MCB 105 in an [32]. If terminal 29 is used as an input, then set
array function. See 5-40 Function Relay. 5-01 Terminal 27 Mode to Input [0].
Relay 3-6 are included in MCB 113.

MG33MD22 - VLT® is a registered Danfoss trademark 3-63

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

5-53 Term. 29 High Ref./Feedb. Value

130BA076.10
Ref.
(RPM)
High Range: Function:
ref.
value Application [-999999.999 - Enter the high reference
P 5-53/

3 3 dependent* 999999.999 value [RPM] for the motor

p 5-58
ReferenceFeed- shaft speed and the high
backUnit] feedback value, see also
5-58 Term. 33 High Ref./
Feedb. Value. Select
Low
ref. terminal 29 as a digital
value
P 5-52/ input (5-02 Terminal 29
p 5-57 Low freq. High freq. Input
P 5-50/ P 5-51/ (Hz) Mode =input [0] (default)
P 5-55 P 5-56
and 5-13 Terminal 29 Digital
Input = applicable value).
5-50 Term. 29 Low Frequency This parameter is available
Range: Function: for FC 302 only.

100 Hz* [0 - 110000 Enter the low frequency limit Application [-999999.999 -
Hz] corresponding to the low motor shaft dependent* 999999.999
speed (i.e., low reference value) in ReferenceFeed-
5-52 Term. 29 Low Ref./Feedb. Value. Refer backUnit]
to the diagram in this section.
This parameter is available for FC 302 5-54 Pulse Filter Time Constant #29
only. Range: Function:
100 [1 - Enter the pulse filter time constant. The
5-51 Term. 29 High Frequency ms* 1000 ms] pulse filter dampens oscillations of the
Range: Function: feedback signal, which is an advantage if
100 Hz* [0 - 110000 Enter the high frequency limit there is a lot of noise in the system. A high
Hz] corresponding to the high motor shaft time constant value results in better
speed (i.e. high reference value) in damping, but also increases the time delay
5-53 Term. 29 High Ref./Feedb. Value. through the filter. This parameter is available
This parameter is available for FC 302 for FC 302 only.
only. This parameter cannot be adjusted while the
motor is running.
5-52 Term. 29 Low Ref./Feedb. Value
5-55 Term. 33 Low Frequency
Range: Function:
Range: Function:
0.000 Reference- [-999999.999 - Enter the low reference
FeedbackUnit* 999999.999 value limit for the motor 100 Hz* [0 - 110000 Enter the low frequency
ReferenceFeed- shaft speed [RPM]. This is Hz] corresponding to the low motor shaft
backUnit] also the lowest feedback speed (i.e., low reference value) in
value, see also 5-57 Term. 5-57 Term. 33 Low Ref./Feedb. Value.
33 Low Ref./Feedb. Value.
Set terminal 29 to digital 5-56 Term. 33 High Frequency
input (5-02 Terminal 29 Range: Function:
Mode =input [0] (default) 100 Hz* [0 - 110000 Enter the high frequency
and 5-13 Terminal 29 Hz] corresponding to the high motor shaft
Digital Input = applicable speed (i.e., high reference value) in
value). 5-58 Term. 33 High Ref./Feedb. Value.
This parameter is
available for FC 302 only.

3-64 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

5-57 Term. 33 Low Ref./Feedb. Value Output value

130BA089.11
Range: Function:
0.000 * [-999999.999 - Enter the low reference value High output
999999.999 ] [RPM] for the motor shaft speed.
3 3
value
P 5-60(term27)
This is also the low feedback
P 5-63(term29)
value, see also 5-52 Term. 29 Low
Ref./Feedb. Value.

5-58 Term. 33 High Ref./Feedb. Value

Range: Function:
Application [-999999.999 - Enter the high High freq. Output
dependent* 999999.999 reference value [RPM] P 5-62(term27) (Hz)
ReferenceFeedbackUnit] for the motor shaft P 5-65(term29)

speed. See also

5-53 Term. 29 High Options for readout output variables:
Ref./Feedb. Value.

Application [-999999.999 - Parameters for configuring the

dependent* 999999.999 scaling and output functions of
ReferenceFeedbackUnit] pulse outputs. The pulse outputs
are designated for terminals 27 or
5-59 Pulse Filter Time Constant #33 29. Select terminal 27 output in
Range: Function: 5-01 Terminal 27 Mode and
100 ms* [1 - 1000 Enter the pulse filter time constant. The terminal 29 output in
ms] low-pass filter reduces the influence on, 5-02 Terminal 29 Mode.
and dampens oscillations in, the feedback [0] No operation
signal from the control. [45] Bus control
This is an advantage, if, for example, there [48] Bus control timeout
is a great amount of noise in the system. [51] MCO controlled
[100] Output frequency
NOTE! [101] Reference
This parameter cannot be adjusted while the motor is [102] Feedback
running. [103] Motor current
[104] Torque relative to limit
3.7.6 5-6* Pulse Outputs [105] Torque relative to rated
[106] Power
These parameters are to configure pulse outputs with their [107] Speed
functions and scaling. Terminal 27 and 29 are allocated to [108] Torque
pulse output via 5-01 Terminal 27 Mode and 5-02 Terminal [109] Max Out Freq
29 Mode, respectively.
5-60 Terminal 27 Pulse Output Variable
NOTE! Option: Function:
These parameters cannot be adjusted while the motor is [0] * No operation Select the desired display output for
running. terminal 27.

[45] Bus ctrl.

[48] Bus ctrl., timeout
[51] MCO controlled
[100] Output frequency
[101] Reference
[102] Feedback
[103] Motor current
[104] Torque rel to limit
[105] Torq relate to rated

MG33MD22 - VLT® is a registered Danfoss trademark 3-65

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

5-60 Terminal 27 Pulse Output Variable 5-66 Terminal X30/6 Pulse Output Variable
Option: Function: Select the variable for read-out on terminal X30/6.
[106] Power This parameter is active when option module MCB 101 is
installed in the Adjustable frequency drive.
3 3 [107] Speed
[108] Torque Same options and functions as parameter group 5-6*.

[109] Max Out Freq Option: Function:

[119] Torque % lim [0] * No operation
[45] Bus ctrl.
5-62 Pulse Output Max Freq #27
[48] Bus ctrl., timeout
Range: Function: [51] MCO controlled
Application [0 - 32000 Set the maximum frequency for [100] Output frequency
dependent* Hz] terminal 27, corresponding to the [101] Reference
output variable selected in [102] Feedback
5-60 Terminal 27 Pulse Output
[103] Motor current
Variable.
[104] Torque rel to limit
5000. Hz* [0 - 32000 Set the maximum frequency for [105] Torq relate to rated
Hz] terminal 27, corresponding to the [106] Power
output variable selected in [107] Speed
5-60 Terminal 27 Pulse Output [108] Torque
Variable. [109] Max Out Freq
[119] Torque % lim
5-63 Terminal 29 Pulse Output Variable
Option: Function: 5-68 Pulse Output Max Freq #X30/6
[0] * No operation Select the desired display output for Select the maximum frequency on terminal X30/6 referring to
terminal 29. This parameter is the output variable in 5-66 Terminal X30/6 Pulse Output Variable.
available for FC 302 only. This parameter cannot be adjusted while the motor is running.
This parameter is active when option module MCB 101 is
[45] Bus ctrl.
mounted in the Adjustable frequency drive.
[48] Bus ctrl., timeout
[51] MCO controlled
Range: Function:
[100] Output frequency Application [0 - 32000 Hz]
dependent*
[101] Reference
[102] Feedback
[103] Motor current 3.7.7 5-7* 24 V Encoder Input
[104] Torque rel to limit
[105] Torq relate to rated Connect the 24 V encoder to terminal 12 (24V DC supply),
[106] Power terminal 32 (Channel A), terminal 33 (Channel B), and
[107] Speed terminal 20 (GND). The digital inputs 32/33 are active for
[108] Torque encoder inputs when 24V encoder is selected in 1-02 Flux
Motor Feedback Source and 7-00 Speed PID Feedback Source.
[109] Max Out Freq
The encoder used is a dual channel (A and B) 24V type.
[119] Torque % lim
Max input frequency: 110kHz.
5-65 Pulse Output Max Freq #29
Set the maximum frequency for terminal 29 corresponding to the Encoder Connection to the Adjustable frequency drive
output variable set in 5-63 Terminal 29 Pulse Output Variable. 24V incremental encoder. Max. cable length 16 ft [5 m].
Range: Function:
5000 Hz* [0 - 32000 Hz]

3-66 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

5-71 Term 32/33 Encoder Direction

Option: Function:
Change the detected encoder rotation
direction without changing the wiring to
the encoder. 3 3
[0] * Clockwise Sets channel A 90° (electrical degrees)
behind channel B upon clockwise rotation
of the encoder shaft.

[1] Counter Sets channel A 90° (electrical degrees)

clockwise ahead of channel B upon clockwise
rotation of the encoder shaft.

NOTE!
This parameter cannot be adjusted while the motor is
running.

3.7.8 5-8* I/O Options

5-80 AHF Cap Reconnect Delay

Range: Function:
130BA646.10

CW 25 s* [1 - 120 Guarantees a minimum off-time for the

A
s] capacitors. The timer starts once the AHF
capacitor disconnects and needs to expire
B before the output is allowed to be on again. It
will only turn on again if the drive power is
between 20% and 30%.

3.7.9 5-9* Bus Controlled

CCW This parameter group selects digital and relay outputs via
A a serial communication bus setting.

5-90 Digital & Relay Bus Control

Range: Function:
B
0* [0 - 2147483647 ] This parameter holds the state of the
digital outputs and relays that is
5-70 Term 32/33 Pulses per Revolution controlled by bus.
Range: Function: A logical '1' indicates that the output is
1024* [1 - 4096 ] Set the encoder pulses per revolution on the high or active.
motor shaft. Read the correct value from the A logical '0' indicates that the output is
encoder. low or inactive.
This parameter cannot be adjusted while the
motor is running.

NOTE!
This parameter cannot be adjusted while the motor is
running.

MG33MD22 - VLT® is a registered Danfoss trademark 3-67

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

Bit 0 Digital Output Terminal 27

Bit 1 Digital Output Terminal 29
Bit 2 Digital Output Terminal X 30/6
Bit 3 Digital Output Terminal X 30/7
3 3 Bit 4 Relay 1 output terminal
Bit 5 Relay 2 output terminal
Bit 6 Option B Relay 1 output terminal
Bit 7 Option B Relay 2 output terminal
Bit 8 Option B Relay 3 output terminal
Bit 9-15 Reserved for future terminals
Bit 16 Option C Relay 1 output terminal
Bit 17 Option C Relay 2 output terminal
Bit 18 Option C Relay 3 output terminal
Bit 19 Option C Relay 4 output terminal
Bit 20 Option C Relay 5 output terminal
Bit 21 Option C Relay 6 output terminal
Bit 22 Option C Relay 7 output terminal
Bit 23 Option C Relay 8 output terminal
Bit 24-31 Reserved for future terminals

5-93 Pulse Out #27 Bus Control

Range: Function:
0.00 %* [0.00 - 100.00 %]

5-94 Pulse Out #27 Timeout Preset

Range: Function:
0.00 %* [0.00 - 100.00 %]

5-95 Pulse Out #29 Bus Control

Range: Function:
0.00 %* [0.00 - 100.00 %]

5-96 Pulse Out #29 Timeout Preset

Range: Function:
0.00 %* [0.00 - 100.00 %]

5-97 Pulse Out #X30/6 Bus Control

Range: Function:
0.00 %* [0.00 - 100.00 %]

5-98 Pulse Out #X30/6 Timeout Preset

Range: Function:
0.00 %* [0.00 - 100.00 %]

3-68 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.8 Parameters: 6-** Analog In/Out 6-01 Live Zero Timeout Function
Option: Function:
3.8.1 6-0* Analog I/O Mode
[21] Coast and

The analog inputs can freely be allocated to be either

voltage (FC 301: 0..10V, FC 302: 0..+/- 10V) or current (FC
trip
3 3
301/FC 302: 0/4..20mA) input. 3.8.2 6-1* Analog Input 1

Parameters for configuring the scaling and limits for

NOTE! analog input 1 (terminal 53).
Thermistors may be connected to either an analog or a
digital input.
Ref./Feedback

130BT103.10
[RPM]
6-00 Live Zero Timeout Time Par 6-xx
'High Ref./ 1500
Range: Function: Feedb. Value'
1200
10 s* [1 - Enter the Live Zero Timeout time period. Live Zero
99 s] Timeout Time is active for analog inputs, i.e., 900

terminal 53 or terminal 54, used as reference or 600

feedback sources. If the reference signal value
Par 6-xx 300
associated with the selected current input falls 'Low Ref./ 150
Feedb. Value'
below 50% of the value set in 6-10 Terminal 53
Ex. 1V 5V 10 V
Low Voltage, 6-12 Terminal 53 Low Current,
Par 6-xx Par 6-xx Analog input
6-20 Terminal 54 Low Voltage or 6-22 Terminal 54 'Low Voltage'or 'High Voltage'or
'Low Current' 'High Current'
Low Current for a time period longer than the time
set in 6-00 Live Zero Timeout Time, the function
selected in 6-01 Live Zero Timeout Function will be 6-10 Terminal 53 Low Voltage
activated. Range: Function:
0.07 V* [Application Enter the low voltage value. This
6-01 Live Zero Timeout Function
dependant] analog input scaling value should
Option: Function: correspond to the minimum reference
Select the timeout function. The function set value, set in 6-14 Terminal 53 Low Ref./
in 6-01 Live Zero Timeout Function will be Feedb. Value. See also the section
activated if the input signal on terminal 53 or Reference Handling.
54 is below 50% of the value in 6-10 Terminal
53 Low Voltage, 6-12 Terminal 53 Low Current, 6-11 Terminal 53 High Voltage
6-20 Terminal 54 Low Voltage or 6-22 Terminal Range: Function:
54 Low Current for a time period defined in
10.00 V* [ par. 6-10 - Enter the high voltage value. This
6-00 Live Zero Timeout Time. If several
10.00 V] analog input scaling value should
timeouts occur simultaneously, the Adjustable
correspond to the high reference/
frequency drive prioritizes the timeout
feedback value set in 6-15 Terminal 53
functions as follows:
High Ref./Feedb. Value.
1. 6-01 Live Zero Timeout Function
2. 8-04 Control Word Timeout Function 6-12 Terminal 53 Low Current

[0] * Off
Range: Function:
[1] Freeze Frozen at the present value 0.14 [Application Enter the low current value. This
output mA* dependant] reference signal should correspond to
[2] Stop Overruled to stop the minimum reference value, set in
3-02 Minimum Reference. The value
[3] Jogging Overruled to jog speed must be set at >2mA in order to
[4] Max. speed Overruled to max. speed activate the Live Zero Timeout
Function in 6-01 Live Zero Timeout
[5] Stop and Overruled to stop with subsequent trip
Function.
trip
[20] Coast

MG33MD22 - VLT® is a registered Danfoss trademark 3-69

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

6-13 Terminal 53 High Current 3.8.3 6-2* Analog Input 2

Range: Function:
20.00 mA* [ par. 6-12 - Enter the high current value
Parameters for configuring the scaling and limits for
analog input 2 (terminal 54).
3 3 20.00 mA] corresponding to the high
reference/feedback set in
6-15 Terminal 53 High Ref./Feedb. 6-20 Terminal 54 Low Voltage
Value. Range: Function:
0.07 V* [Application Enter the low voltage value. This
6-14 Terminal 53 Low Ref./Feedb. Value dependant] analog input scaling value should
Range: Function: correspond to the minimum
0.000 * [-999999.999 - Enter the analog input scaling reference value, set in 3-02 Minimum
999999.999 ] value that corresponds to the low Reference. See also the section
voltage/low current set in Reference Handling.
6-10 Terminal 53 Low Voltage and
6-12 Terminal 53 Low Current. 6-21 Terminal 54 High Voltage
Range: Function:
6-15 Terminal 53 High Ref./Feedb. Value 10.00 V* [ par. 6-20 - Enter the high voltage value. This
Range: Function: 10.00 V] analog input scaling value should
Application [-999999.999 - Enter the analog input correspond to the high reference/
dependent* 999999.999 scaling value that feedback value set in 6-25 Terminal 54
ReferenceFeed- corresponds to the High Ref./Feedb. Value.
backUnit] maximum reference
feedback value set in 6-22 Terminal 54 Low Current
6-11 Terminal 53 High Range: Function:
Voltage and 6-13 Terminal
0.14 [Application Enter the low current value. This
53 High Current.
mA* dependant] reference signal should correspond to
Application [-999999.999 - Enter the analog input the minimum reference value, set in
dependent* 999999.999 scaling value that 3-02 Minimum Reference. The value
ReferenceFeed- corresponds to the must be set at >2mA in order to
backUnit] maximum reference activate the Live Zero Timeout
feedback value set in Function in 6-01 Live Zero Timeout
6-11 Terminal 53 High Function.
Voltage and 6-13 Terminal
53 High Current. 6-23 Terminal 54 High Current
Range: Function:
6-16 Terminal 53 Filter Time Constant 20.00 mA* [ par. 6-22 - Enter the high current value
Range: Function: 20.00 mA] corresponding to the high reference/
0.001 s* [0.001 - Enter the time constant. This is a first- feedback value set in 6-25 Terminal
10.000 s] order digital low pass filter time 54 High Ref./Feedb. Value.
constant for suppressing electrical noise
in terminal 53. A high time constant 6-24 Terminal 54 Low Ref./Feedb. Value
value improves dampening but also Range: Function:
increases the time delay through the
0 ReferenceFeed- [-999999.999 - Enter the analog
filter.
backUnit* 999999.999 input scaling value
ReferenceFeed- that corresponds to
NOTE! backUnit] the minimum
This parameter cannot be adjusted while the motor is reference feedback
running. value set in
3-02 Minimum
Reference.

3-70 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

6-25 Terminal 54 High Ref./Feedb. Value 6-34 Term. X30/11 Low Ref./Feedb. Value
Range: Function: Range: Function:
Application [-999999.999 - Enter the analog input 0.000 * [-999999.999 - Sets the analog input scaling
dependent* 999999.999
ReferenceFeed-
scaling value that
corresponds to the
999999.999 ] value to correspond to the low
voltage value (set in 6-30 Terminal 3 3
backUnit] maximum reference X30/11 Low Voltage).
feedback value set in
3-03 Maximum Reference. 6-35 Term. X30/11 High Ref./Feedb. Value
Application [-999999.999 - Enter the analog input Range: Function:
dependent* 999999.999 scaling value that 100.000 * [-999999.999 - Sets the analog input scaling
ReferenceFeed- corresponds to the 999999.999 ] value to correspond to the high
backUnit] maximum reference voltage value (set in
feedback value set in 6-31 Terminal X30/11 High
3-03 Maximum Reference. Voltage).

6-26 Terminal 54 Filter Time Constant 6-36 Term. X30/11 Filter Time Constant
Range: Function: Range: Function:
0.001 s* [0.001 - Enter the time constant. This is a first- 0.001 s* [0.001 - 10.000 s] A 1st order digital low pass filter
10.000 s] order digital low pass filter time time constant for suppressing
constant for suppressing electrical noise electrical noise on terminal X30/11.
in terminal 54. A high time constant
value improves dampening but also NOTE!
increases the time delay through the This parameter cannot be changed while the motor is
filter. running.

NOTE! 3.8.5 6-4* Analog Input 4 MCB 101

This parameter cannot be adjusted while the motor is
running.
Parameter group for configuring the scale and limits for
analog input 4 (X30/12) placed on option module MCB
3.8.4 6-3* Analog Input 3 MCB 101 101.

6-40 Terminal X30/12 Low Voltage

Parameter group for configuring the scale and limits for
analog input 3 (X30/11) placed on option module MCB Range: Function:
101. 0.07 V* [ 0.00 - par. Sets the analog input scaling value to
6-41 V] correspond to the low reference/
6-30 Terminal X30/11 Low Voltage
feedback value set in 6-44 Term.
Range: Function: X30/12 Low Ref./Feedb. Value.
0.07 V* [ 0.00 - par. Sets the analog input scaling value to
6-31 V] correspond to the low reference/ 6-41 Terminal X30/12 High Voltage
feedback value (set in 6-34 Term. Range: Function:
X30/11 Low Ref./Feedb. Value).
10.00 V* [ par. 6-40 - Sets the analog input scaling value to
10.00 V] correspond to the high reference/
6-31 Terminal X30/11 High Voltage
feedback value set in 6-45 Term.
Range: Function: X30/12 High Ref./Feedb. Value.
10.00 V* [ par. 6-30 - Sets the analog input scaling value to
10.00 V] correspond to the high reference/ 6-44 Term. X30/12 Low Ref./Feedb. Value
feedback value (set in 6-35 Term. Range: Function:
X30/11 High Ref./Feedb. Value).
0.000 * [-999999.999 - Sets the analog output scaling
999999.999 ] value to correspond to the low
voltage value set in 6-40 Terminal
X30/12 Low Voltage.

MG33MD22 - VLT® is a registered Danfoss trademark 3-71

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

6-45 Term. X30/12 High Ref./Feedb. Value 6-50 Terminal 42 Output

Range: Function: Option: Function:
100.000 * [-999999.999 - Sets the analog input scaling Example: Inverter norm current (11kW) = 24A.

3 3 999999.999 ] value to correspond to the high

voltage value set in
160% = 38.4A. Motor norm current = 22A
Readout 11.46mA.
6-41 Terminal X30/12 High 20 mA x 22 A
= 11.46 mA
Voltage. 38.4 A
In case the norm motor current is equal to
6-46 Term. X30/12 Filter Time Constant 20mA, the output setting of 6-52 Terminal 42
Output Max Scale is:
Range: Function:
I VLT x 100
0.001 s* [0.001 - 10.000 s] A 1st order digital low pass filter Max 38.4 x 100
= = 175 %
I Motor 22
time constant for suppressing Norm
electrical noise on terminal X30/12. [104] Torque rel The torque setting is related to setting in
to limit 4-16 Torque Limit Motor Mode
NOTE! [105] Torq relate The torque is related to the motor torque
This parameter cannot be changed while the motor is
to rated setting.
running.
[106] Power Taken from 1-20 Motor Power [kW].

3.8.6 6-5* Analog Output 1 [107] Speed Taken from 3-03 Maximum Reference. 20mA =
value in 3-03 Maximum Reference
Parameters for configuring the scaling and limits for [108] Torque Torque reference related to 160% torque.
analog output 1, i.e., Terminal 42. Analog outputs are
[109] Max Out 0Hz = 0mA,4-19 Max Output Frequency =
current outputs: 0/4 – 20mA. Common terminal (terminal
Freq 20mA.
39) is the same terminal and has the same electrical
potential for analog common and digital common [113] PID
connection. Resolution on analog output is 12 bit. Clamped
Output
6-50 Terminal 42 Output
[119] Torque %
Option: Function: lim
Select the function of Terminal 42 as an [130] Output 0Hz = 4mA, 100Hz = 20mA
analog current output. Depending on the freq.
selection the output is either a 0-20mA or 4-20mA
4-20mA output. The current value can be [131] Reference 3-00 Reference Range [Min-Max] 0% = 4mA;
read out in LCP in 16-65 Analog Output 42 4-20mA 100% = 20mA
[mA]. 3-00 Reference Range [-Max-Max] -100% =
[0] * No When no signal on the analog output. 4mA; 0% = 12 mA; +100% = 20 mA
operation [132] Feedback
[52] MCO 4-20mA
0-20mA [133] Motor cur. Value is taken from 16-37 Inv. Max. Current.
[53] MCO 4-20mA Inverter max. current (160% current) is equal
4-20mA to 20mA.
[100] Output 0Hz = 0mA; 100Hz = 20mA.
Example: Inverter norm current (11kW) = 24A.
frequency
160% = 38.4A. Motor norm current = 22A
[101] Reference 3-00 Reference Range [Min - Max] 0% = 0mA;
Readout 11.46mA.
100% = 20mA
16 mA x 22 A
3-00 Reference Range [-Max - Max] -100% = 38.4 A
+ 4 mA = 13.17 mA

0mA; 0% = 10mA; +100% = 20 mA In case the norm motor current is equal to

[102] Feedback 20mA, the output setting of 6-62 Terminal
[103] Motor Value is taken from 16-37 Inv. Max. Current. X30/8 Max. Scale is:
current Inverter max. current (160% current) is equal I VLT x 100
Max 38.4 x 100
to 20mA. = = 175 %
I Motor 22
Norm

3-72 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

6-50 Terminal 42 Output 6-52 Terminal 42 Output Max Scale

Option: Function: Range: Function:
[134] Torq.% lim The torque setting is related to setting in 100.00 %* [0.00 - 200.00 %]
4-20 mA

[135] Torq.%
4-16 Torque Limit Motor Mode.

The torque setting is related to the motor

20 mA / desired maximum current x 100 %

i .e . 10 mA :
20
x 100 = 200 %
3 3
10
nom 4-20 torque setting.

130BA075.11
Current

mA (mA)

20
[136] Power Taken from 1-20 Motor Power [kW]
4-20mA
[137] Speed Taken from 3-03 Maximum Reference. 20mA =
0/4
4-20mA Value in 3-03 Maximum Reference. 0% Analog Analog 100% Variable for
output Min Output Max output
Scale Scale example: Speed
par. 6-52 (RPM)
[138] Torque Torque reference related to 160% torque.
par. 6-51

4-20mA
[139] Bus ctrl. An output value set from serial communi- 6-53 Terminal 42 Output Bus Control
0-20 mA cation bus process data. The output will work Range: Function:
independently of internal functions in the
0.00 %* [0.00 - 100.00 %]
Adjustable frequency drive.

[140] Bus ctrl. An output value set from serial communi- 6-54 Terminal 42 Output Timeout Preset
4-20 mA cation bus process data. The output will work Range: Function:
independently of internal functions in the 0.00 %* [0.00 - 100.00 %]
Adjustable frequency drive.
6-55 Analog Output Filter
[141] Bus ctrl 4-54 Warning Reference Low defines the
Option: Function:
0-20mA t.o. behavior of the analog output in case of bus
timeout. The following readout analog parameters from
selection in 6-50 Terminal 42 Output have a filter
[142] Bus ctrl 4-54 Warning Reference Low defines the selected when 6-55 Analog Output Filter is on:
4-20mA t.o. behavior of the analog output in case of bus
timeout. Selection 0-20mA 4-20mA

[149] Torque % Analog output at zero torque = 12mA. Motor current (0 - Imax) [103] [133]
lim 4-20mA Motoric torque will increase the output Torque limit (0 - Tlim) [104] [134]
current to max torque limit 20mA (set in Rated torque (0 - Tnom) [105] [135]
4-16 Torque Limit Motor Mode). Power (0 - Pnom) [106] [136]
Generative torque will decrease the output to Speed (0 - Speedmax) [107] [137]
torque limit Generator Mode (set in
4-17 Torque Limit Generator Mode) [0] * Off Filter off
Ex: 4-16 Torque Limit Motor Mode : 200% and
4-17 Torque Limit Generator Mode: 200%. [1] On Filter on
20mA = 200% Motoric and 4mA = 200%
Generatoric.
3.8.7 6-6* Analog Output 2 MCB 101
0mA 4mA 12 mA 20 mA
130BB372.10

Par 4-17
(200%)
0% Torque Par 4-16
(200%)
Analog outputs are current outputs: 0/4 - 20mA. Common
terminal (terminal X30/8) is the same terminal and
electrical potential for analog common connection.
Resolution on analog output is 12 bit.
[150] Max Out Fr 0hz = 0mA,4-19 Max Output Frequency =
6-60 Terminal X30/8 Output
4-20mA 20mA.
Option: Function:
6-51 Terminal 42 Output Min Scale Select the function of Terminal X30/8 as an
Range: Function: analog current output. Depending on the
selection the output is either a 0-20mA or
0.00 %* [0.00 - 200.00 %]
4-20mA output. The current value can be

MG33MD22 - VLT® is a registered Danfoss trademark 3-73

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

6-60 Terminal X30/8 Output 6-60 Terminal X30/8 Output

Option: Function: Option: Function:
read out in LCP in 16-65 Analog Output 42 [131] Reference 3-00 Reference Range [Min-Max] 0% = 4mA;

3 3 [0] * No
[mA].

When no signal on the analog output.

4-20mA 100% = 20mA
3-00 Reference Range [-Max-Max] -100% =
4mA; 0% = 12 mA; +100% = 20 mA
operation
[52] MCO [132] Feedback
0-20mA 4-20mA
[100] Output 0hz = 0mA; 100hz = 20mA. [133] Motor cur. Value is taken from 16-37 Inv. Max. Current.
frequency 4-20mA Inverter max. current (160% current) is equal
[101] Reference 3-00 Reference Range [Min - Max] 0% = 0mA; to 20mA.
100% = 20mA Example: Inverter norm current (15 hp [11
3-00 Reference Range [-Max - Max] -100% = kW]) = 24 A. 160% = 38.4 A. Motor norm
0mA; 0% = 10mA; +100% = 20 mA current = 22 A Readout 11.46mA.
[102] Feedback 16 mA x 22 A
= 9.17 mA
38.4 A
[103] Motor Value is taken from 16-37 Inv. Max. Current.
If the norm motor current is equal to 20mA,
current Inverter max. current (160% current) is equal
the output setting of 6-62 Terminal X30/8
to 20mA.
Max. Scale is:
Example: Inverter norm current (15 hp [11
I VLT x 100
kW]) = 24 A. 160% = 38.4 A. Motor norm Max 38.4 x 100
= = 175 %
I Motor 22
current = 22 A Readout 11.46mA. Norm

20 mA x 22 A [134] Torq.% lim The torque setting is related to setting in

= 11.46 mA
38.4 A
4-20 mA 4-16 Torque Limit Motor Mode.
If the norm motor current is equal to 20mA,
the output setting of 6-62 Terminal X30/8 [135] Torq.% The torque setting is related to the motor
Max. Scale is: nom 4-20 torque setting.
mA
I VLT x 100
Max 38.4 x 100 [136] Power Taken from 1-20 Motor Power [kW]
= = 175 %
I Motor 22
Norm 4-20mA
[104] Torque rel The torque setting is related to setting in [137] Speed Taken from 3-03 Maximum Reference. 20mA =
to limit 4-16 Torque Limit Motor Mode. 4-20mA Value in 3-03 Maximum Reference.

[105] Torq relate The torque is related to the motor torque [138] Torque Torque reference related to 160% torque.
to rated setting. 4-20mA
[139] Bus ctrl. An output value set from serial communi-
[106] Power Taken from 1-20 Motor Power [kW].
0-20 mA cation bus process data. The output will work
[107] Speed Taken from 3-03 Maximum Reference. 20mA = independently of internal functions in the
value in 3-03 Maximum Reference Adjustable frequency drive.
[108] Torque Torque reference related to 160% torque. [140] Bus ctrl. An output value set from serial communi-
[109] Max Out In relation to 4-19 Max Output Frequency. 4-20 mA cation bus process data. The output will work
Freq independently of internal functions in the
[113] PID Adjustable frequency drive.
Clamped [141] Bus ctrl 4-54 Warning Reference Low defines the
Output 0-20mA t.o. behavior of the analog output in case of bus
[119] Torque % timeout.
lim
[142] Bus ctrl 4-54 Warning Reference Low defines the
[130] Output 0hz = 4mA, 100hz = 20mA
4-20mA t.o. behavior of the analog output in case of bus
freq.
timeout.
4-20mA
[149] Torque % Torque% Lim 4-20mA: Torque reference.
lim 4-20mA 3-00 Reference Range [Min-Max] 0% = 4mA;
100% = 20mA

3-74 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

6-60 Terminal X30/8 Output 6-70 Terminal X45/1 Output

Option: Function: Option: Function:
3-00 Reference Range [-Max - Max] -100% = Example: Inverter norm current (15 hp [11

3 3
4mA; 0% = 12 mA; +100% = 20 mA kW]) = 24 A. 160% = 38.4 A. Motor norm
current = 22 A Readout 11.46mA.
[150] Max Out Fr In relation to 4-19 Max Output Frequency.
20 mA x 22 A
= 11.46 mA
4-20mA 38.4 A
If the norm motor current is equal to 20mA,
6-61 Terminal X30/8 Min. Scale
the output setting of 6-52 Terminal 42
Range: Function: Output Max Scale is:
0.00 %* [0.00 - 200.00 %] I VLT x 100
Max 38.4 x 100
= = 175 %
I Motor 22
6-62 Terminal X30/8 Max. Scale Norm
[104] Torque rel The torque setting is related to setting in
Range: Function:
to lim 4-16 Torque Limit Motor Mode
100.00 %* [0.00 - 200.00 %]
0-20mA
20 mA / desired maximum current x 100 % [105] Torque rel The torque is related to the motor torque
20 − 4 to rated setting.
i .e . 10 mA : x 100 = 160 %
10
motor
6-63 Terminal X30/8 Bus Control
torque
Range: Function: 0-20mA
0.00 %* [0.00 - 100.00 %] [106] Power Taken from 1-20 Motor Power [kW].
0-20mA
6-64 Terminal X30/8 Output Timeout Preset
[107] Speed Taken from 3-03 Maximum Reference. 20mA
Range: Function: 0-20mA = value in 3-03 Maximum Reference
0.00 %* [0.00 - 100.00 %] [108] Torque ref. Torque reference related to 160% torque.
0-20mA
3.8.8 6-7* Analog Output 3 MCB 113 [109] Max Out In relation to 4-19 Max Output Frequency.
Freq 0–
Parameters for configuring the scaling and limits for 20mA
analog output 3, Terminal X45/1 and X45/2. Analog [130] Output freq. 0hz = 4mA, 100hz = 20mA
outputs are current outputs: 0/4 – 20mA. Resolution on 4–20 mA
analog output is 11 bit. [131] Reference 3-00 Reference Range [Min-Max] 0% = 4mA;
4–20 mA 100% = 20mA
6-70 Terminal X45/1 Output
3-00 Reference Range [-Max-Max] -100% =
Option: Function: 4mA; 0% = 12 mA; +100% = 20 mA
Select the function of Terminal X45/1 as an [132] Feedback 4–
analog current output. 20 mA
[0] No When no signal on the analog output. [133] Motor cur. Value is taken from 16-37 Inv. Max. Current.
operation 4–20 mA Inverter max. current (160% current) is equal
[52] MCO 305 to 20mA.
0-20mA Example: Inverter norm current (15 hp [11
[53] MCO 305 kW]) = 24 A. 160% = 38.4 A. Motor norm
4-20mA current = 22 A Readout 11.46mA.
[100] Output 0hz = 0mA; 100hz = 20mA. 16 mA x 22 A
= 9.17 mA
38.4 A
frequency
If the norm motor current is equal to 20mA,
0-20mA
the output setting of 6-52 Terminal 42
[101] Reference 3-00 Reference Range [Min - Max] 0% = 0mA;
Output Max Scale is:
0-20mA 100% = 20mA I VLT x 100
Max 38.4 x 100
3-00 Reference Range [-Max - Max] -100% = = = 175 %
I Motor 22
0mA; 0% = 10mA; +100% = 20 mA Norm

[102] Feedback [134] Torque% The torque setting is related to setting in

[103] Motor Value is taken from 16-37 Inv. Max. Current. lim. 4-20mA 4-16 Torque Limit Motor Mode.
current Inverter max. current (160% current) is equal
0-20mA to 20mA.

MG33MD22 - VLT® is a registered Danfoss trademark 3-75

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

6-70 Terminal X45/1 Output 6-72 Terminal X45/1 Output Max Scale
Option: Function: Range: Function:
[135] Torque% The torque setting is related to the motor maximum output (100%), calculate the

3 3 nom torque setting. percentage value as follows (example where

4-20mA desired max. output is 10mA):
[136] Power 4–20 Taken from 1-20 Motor Power [kW] I RANGE mA
x 100 %
I DESIRED MAX mA
mA
20 − 4 mA
[137] Speed 4–20 Taken from 3-03 Maximum Reference. 20mA = x 100 % = 160 %
10 mA
mA = Value in 3-03 Maximum Reference.
Current

130BA877.10
[138] Torque 4–20 Torque reference related to 160% torque. [mA]
mA
[139] Bus ctrl. An output value set from the serial 20
0-20 mA communication bus process data. The
output will work independently of internal
functions in the Adjustable frequency drive.
[140] Bus ctrl. An output value set from the serial
4-20 mA communication bus process data. The
output will work independently of internal 0/4

functions in the Adjustable frequency drive. 0% Analogue Analogue 100% Variable for
output Min Output Max output
[141] Bus ctrl. 4-54 Warning Reference Low defines the Scale Scale example:Speed
0-20mA, behavior of the analog output in case of bus par. 6-71 par. 6-72 [RPM]

timeout timeout.
[142] Bus ctrl. 4-54 Warning Reference Low defines the 6-73 Terminal X45/1 Output Bus Control
4-20mA, behavior of the analog output in case of bus
Range: Function:
timeout timeout.
0.00%* [0.00–100.00%] Holds the level of Analog Output 3
[150] Max Out In relation to 4-19 Max Output Frequency.
(terminal X45/1) if controlled by bus.
Freq
4-20mA 6-74 Terminal X45/1 Output Timeout Preset
6-71 Terminal X45/1 Output Min Scale Range: Function:
Range: Function: 0.00%* [0.00– Holds the preset level of Analog Output
100.00%] 3 (terminal X45/1).
0.00%* [0.00– Scale the minimum output of the selected
In case of a bus timeout and a timeout
200.00%] analog signal at terminal X45/1 as a
function is selected in 6-70 Terminal
percentage of the maximum signal value,
X45/1 Output the output will preset to
e.g., if 0mA (or 0hz) is desired at 25% of
this level.
the maximum output value, then program
25%. Scaling values up to 100% can never
be higher than the corresponding setting 3.8.9 6-8* Analog Output 4 MCB 113
in 6-72 Terminal X45/1 Max. Scale.
Parameters for configuring the scaling and limits for
6-72 Terminal X45/1 Output Max Scale
analog output 4. Terminal X45/3 and X45/4. Analog
Range: Function: outputs are current outputs: 0/4 – 20mA. Resolution on
100%* [0.00– Scale the maximum output of the selected analog output is 11 bit.
200.00%] analog signal at terminal X45/1. Set the value
6-80 Terminal X45/3 Output
to the maximum value of the current signal
output. Scale the output to give a current Option: Function:
lower than 20 mA at full scale, or 20 mA at Select the function of Terminal X45/3 as an
an output below 100% of the maximum analog current output.
signal value. If 20mA is the desired output [0] * No operation Same selections available as for 6-70 Terminal
current at a value between 0–100% of the X45/1 Output
full-scale output, program the percentage
value in the parameter, i.e., 50% = 20mA. If a
current between 4 and 20mA is desired at

3-76 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

6-81 Terminal X45/3 Output Min Scale

Option: Function:
[0.00%] * 0.00– Scales the minimum output of the
200.00% selected analog signal on terminal X45/3.
Scale the minimum value as a percentage 3 3
of the maximum signal value, i.e., 0mA (or
0hz) is desired at 25% of the maximum
output value and 25% is programmed.
The value can never be higher than the
corresponding setting in 6-82 Terminal
X45/3 Max. Scale if value is below 100%.
This parameter is active when option
module MCB 113 is mounted in the
Adjustable frequency drive.

6-82 Terminal X45/3 Output Max Scale

Option: Function:
[0.00%] 0.00– Scales the maximum output of the selected
* 200.00% analog signal on terminal X45/3. Scale the
value to the desired maximum value of the
current signal output. Scale the output to
give a lower current than 20mA at full scale
or 20mA at an output below 100% of the
maximum signal value. If 20mA is the
desired output current at a value between
0–100% of the full-scale output, program the
percentage value in the parameter, i.e., 50%
= 20mA. If a current between 4 and 20mA is
desired at maximum output (100%),
calculate the percentage value as follows
(example where desired max. output is
10mA):
I RANGE mA
x 100 %
I DESIRED MAX mA
20 − 4 mA
= x 100 % = 160 %
10 mA

6-83 Terminal X45/3 Output Bus Control

Option: Function:
[0.00%] * 0.00–100.00% Holds the level of output 4 (X45/3) if
controlled by bus.

6-84 Terminal X45/3 Output Timeout Preset

Option: Function:
[0.00%] * 0.00–100.00% Holds the present level of output 4
(X45/3). If a bus timeout and a timeout
function are selected in 6-80 Terminal
X45/3 Output, the output will preset to
this level.

MG33MD22 - VLT® is a registered Danfoss trademark 3-77

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.9 Parameters: 7-** Controllers 7-02 Speed PID Proportional Gain

Range: Function:
3.9.1 7-0* Speed PID Ctrl.
0 N/A* [0.000 - Enter the speed controller proportional

3 3 7-00 Speed PID Feedback Source

1.000
N/A]
gain. The proportional gain amplifies
the error (i.e., the deviation between
Option: Function: the feedback signal and the setpoint).
Select the encoder for closed-loop This parameter is used with 1-00 Config-
feedback. uration Mode Speed open-loop [0] and
The feedback may come from a Speed closed-loop [1] control. Quick
different encoder (typically mounted control is obtained at high amplifi-
on the application itself) than the cation. However, if the amplification is
motor mounted encoder feedback too great, the process may become
selected in 1-02 Flux Motor Feedback unstable.
Source. If the selection is xxx.xxx, use this
parameter. If the selection is xxx.xxxx,
[0] * Motor feedb. P1-02
use 3-83 Quick Stop S-ramp Ratio at
[1] 24V encoder
Decel. Start.
[2] MCB 102
[3] MCB 103
7-03 Speed PID Integral Time
[4] MCO Encoder 1 X56
Range: Function:
[5] MCO Encoder 2 X55
Application [2.0 -
[6] Analog input 53
dependent* 20000.0
[7] Analog input 54
ms]
[8] Frequency input 29
Application [2.0 - Enter the speed controller integral
[9] Frequency input 33
dependent* 20000.0 time, which determines the time the
NOTE! ms] internal PID control takes to correct
errors. The greater the error, the
This parameter cannot be adjusted while the motor is
more quickly the gain increases. The
running.
integral time causes a delay of the
signal and therefore a damping
NOTE! effect, and can be used to eliminate
If separate encoders are used (FC 302 only), the ramp steady state speed error. Obtain quick
settings parameters in the following groups: 3-4*, 3-5*, control through a short integral time,
3-6*, 3-7* and 3-8* must be adjusted according to the gear though if the integral time is too
ratio between the two encoders. short, the process becomes unstable.
An excessively long integral time
7-02 Speed PID Proportional Gain disables the integral action, leading
Range: Function: to major deviations from the required
reference, since the process regulator
Application [0.000 - Enter the speed controller proportional
takes too long to regulate errors. This
dependent* 1.000 ] gain. The proportional gain amplifies
parameter is used with Speed open-
the error (i.e., the deviation between
loop [0] and Speed closed-loop [1]
the feedback signal and the setpoint).
control, set in 1-00 Configuration
This parameter is used with 1-00 Config-
Mode.
uration Mode Speed open-loop [0] and
Speed closed-loop [1] control. Quick
7-04 Speed PID Differentiation Time
control is obtained at high amplifi-
cation. However, if the amplification is Range: Function:
too great, the process may become Application [0.0 - Enter the speed controller differentiation
unstable. dependent* 200.0 time. The differentiator does not react to
Use this parameter for values with ms] constant error. It provides gain propor-
three decimals. For a selection with tional to the rate of change of the speed
four decimals, use 3-83 Quick Stop S- feedback. The quicker the error changes,
ramp Ratio at Decel. Start. the stronger the gain from the differen-

3-78 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

7-04 Speed PID Differentiation Time 7-06 Speed PID Lowpass Filter Time
Range: Function: Range: Function:
tiator. The gain is proportional with the higher than 1.6 Hz, the PID regulator
speed at which errors change. Setting
this parameter to zero disables the
does not react.
Practical settings of 7-06 Speed PID 3 3
differentiator. This parameter is used Lowpass Filter Time taken from the
with 1-00 Configuration Mode Speed number of pulses per revolutions from
closed-loop [1] control. encoder:

Application [0.0 - Enter the speed controller differentiation Encoder PPR 7-06 Speed PID
dependent* 200.0 time. The differentiator does not react to Lowpass Filter Time
ms] constant error. It provides gain propor-
512 10 ms
tional to the rate of change of the speed
1,024 5 ms
feedback. The quicker the error changes,
2,048 2 ms
the stronger the gain from the differen-
4,096 1 ms
tiator. The gain is proportional with the
speed at which errors change. Setting
this parameter to zero disables the Note that severe filtering can be
differentiator. This parameter is used detrimental to dynamic performance.
with 1-00 Configuration Mode Speed This parameter is used with 1-00 Config-
closed-loop [1] control. uration Mode Speed closed-loop [1] and
Torque [2] control.
7-05 Speed PID Diff. Gain Limit The filter time in flux sensorless must
be adjusted to 3–5 ms.
Range: Function:
5.0* [1.0 - Set a limit for the gain provided by the differ-
20.0 ] entiator. Since the differential gain increases at
higher frequencies, limiting the gain may be
useful. For example, set up a pure D-link at low
frequencies and a constant D-link at higher
frequencies. This parameter is used with
1-00 Configuration Mode Speed closed-loop [1]
control.

7-06 Speed PID Lowpass Filter Time

Range: Function:
Application [1.0 -
dependent* 100.0
ms]
Application [1.0 - Set a time constant for the speed
dependent* 100.0 control low-pass filter. The low-pass
ms] filter improves steady-state performance
and dampens oscillations on the
feedback signal. This is an advantage if
there is a great amount on noise in the
system; see figure below. For example,
if a time constant (τ) of 100 ms is
programmed, the cut-off frequency for
the low-pass filter will be 1/0.1= 10
RAD/sec., corresponding to (10/2 x π) =
1.6 Hz. The PID regulator only regulates
a feedback signal that varies by a
frequency of less than 1.6 Hz. If the
feedback signal varies by a frequency

MG33MD22 - VLT® is a registered Danfoss trademark 3-79

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

Feedback

175ZA293.11

130BA871.10
Disturbed feedback signal

3 3 n1 n2

Motor

Par 7-07=1.00 Par 7-07=n1/n2

7-08 Speed PID Feed Forward Factor

Range: Function:
0 %* [0 - 500 %] The reference signal bypasses the speed
0.6 t (Sec.) controller by the amount specified. This
feature increases the dynamic performance
of the speed control loop.
Lowpass filter
7-09 Speed PID Error Correction w/ Ramp
fg = 10 Hz Range: Function:
300 RPM* [10 - 100000 The speed error between ramp and
Feedback RPM] actual speed is held up against the
setting in this parameter. If the speed
error exceeds this parameter entry,
Filtered feedback signal the speed error will be corrected via
ramping in a controlled way.

Motor
130BC026.10

Speed

7-09

Torque Time
Limit
Motor
Speed

0.6 t (Sec.)
7-09

7-07 Speed PID Feedback Gear Ratio Torque

Limit Time
Range: Function: Ramp Motor Speed
1.0000* [Application dependant]

3.9.2 7-1* Torque PI Control

Parameters for configuring the torque PI control in torque

open-loop (1-00 Configuration Mode).

3-80 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

7-12 Torque PI Proportional Gain 7-22 Process CL Feedback 2 Resource

Range: Function: Option: Function:
100 %* [0 - 500 %] Enter the proportional gain value for the [3] Frequency input 29
torque controller. Selection of a high value
makes the controller react faster. Too high
[4]
[7]
Frequency input 33
Analog input X30/11 3 3
a setting leads to controller instability. [8] Analog input X30/12
[15] Analog Input X48/2
7-13 Torque PI Integration Time
Range: Function: 3.9.4 7-3* Process PID Ctrl.
0.020 s* [0.002 - 2.000 Enter the integration time for the
s] torque controller. Selecting a low value
7-30 Process PID Normal/Inverse Control
causes the controller to react faster.
Too low a setting leads to control
Option: Function:
instability. Normal and inverse control are implemented by
introducing a difference between the reference
signal and the feedback signal.
3.9.3 7-2* Process Ctrl. Feedb. [0] * Normal Sets process control in order to increase the
output frequency.
Select the feedback sources for the process PID control, [1] Inverse Sets process control in order to reduce the output
and the way in which this feedback should be handled. frequency.

7-20 Process CL Feedback 1 Resource 7-31 Process PID Anti Windup

Option: Function: Option: Function:
The effective feedback signal is made [0] Off Continues regulation of an error even when the
up of the sum of up to two different output frequency cannot be increased or decreased.
input signals.
Select which Adjustable frequency [1] * On Ceases regulation of an error when the output
drive input should be treated as the frequency can no longer be adjusted.
source of the first of these signals.
The second input signal is defined in 7-32 Process PID Start Speed
7-22 Process CL Feedback 2 Resource. Range: Function:
[0] * No function 0 RPM* [0 - Enter the motor speed to be attained as a
6000 start signal for commencement of PID
[1] Analog input 53
RPM] control. When the power is switched on, the
[2] Analog input 54
Adjustable frequency drive will commence
[3] Frequency input 29
ramping and then operate under speed
[4] Frequency input 33
open-loop control. Thereafter, when the
[7] Analog input X30/11
process PID start speed is reached, the
[8] Analog input X30/12 Adjustable frequency drive will change over
[15] Analog Input X48/2 to process PID control.

7-22 Process CL Feedback 2 Resource

7-33 Process PID Proportional Gain
Option: Function:
Range: Function:
The effective feedback signal is made
0.01* [0.00 - 10.00 ] Enter the PID proportional gain. The
up of the sum of up to two different
proportional gain multiplies the error
input signals. Select which Adjustable
between the setpoint and the feedback
frequency drive input should be
signal.
treated as the source of the second
of these signals. The first input signal
7-34 Process PID Integral Time
is defined in 7-20 Process CL Feedback
1 Resource. Range: Function:
10000.00 s* [0.01 - Enter the PID integral time. The
[0] * No function
10000.00 s] integrator provides an increasing
[1] Analog input 53
gain at a constant error between
[2] Analog input 54

MG33MD22 - VLT® is a registered Danfoss trademark 3-81

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

7-34 Process PID Integral Time 3.9.5 7-4* Advanced Process PID Ctrl.
Range: Function:
the setpoint and the feedback Parameter group 7-4* is only used if 1-00 Configuration
Mode is set to [7] Extended PID speed CL or [8] Extended
3 3 signal. The integral time is the time
needed by the integrator to reach PID Speed OL.
the same gain as the proportional 7-40 Process PID I-part Reset
gain.
Option: Function:
[0] * No
7-35 Process PID Differentiation Time
[1] Yes Select Yes [1] to reset the I-part of the process PID
Range: Function:
controller. The selection will automatically revert to No
0.00 s* [0.00 - Enter the PID differentiation time. The [0]. Resetting the I-part makes it possible to start from
10.00 s] differentiator does not react to a constant a well-defined point after changing something in the
error, but provides a gain only when the process, e.g., changing a textile roll.
error changes. The shorter the PID differ-
entiation time, the stronger the gain from 7-41 Process PID Output Neg. Clamp
the differentiator.
Range: Function:
7-36 Process PID Diff. Gain Limit -100 %* [Application Enter a negative limit for the
Range: Function: dependant] process PID controller output.

5.0* [1.0 - Enter a limit for the differentiator gain (DG). If

7-42 Process PID Output Pos. Clamp
50.0 ] there is no limit, the DG will increase when
there are fast changes. Limit the DG to obtain Range: Function:
a pure differentiator gain at slow changes, 100 %* [Application Enter a positive limit for the
and a constant differentiator gain where fast dependant] process PID controller output.
changes occur.
7-43 Process PID Gain Scale at Min. Ref.
7-38 Process PID Feed Forward Factor Range: Function:
Range: Function: 100 %* [0 - 100 Enter a scaling percentage to apply to the
0 %* [0 - Enter the PID feed forward (FF) factor. The FF %] process PID output when operating at the
200 %] factor sends a constant fraction of the reference minimum reference. The scaling percentage
signal to bypass PID control, which means that will be adjusted linearly between the scale
PID control only affects the remaining fraction of at min. ref. (7-43 Process PID Gain Scale at
the control signal. Any change to this parameter Min. Ref.) and the scale at max. ref.
will thus affect the motor speed. When the FF (7-44 Process PID Gain Scale at Max. Ref.).
factor is activated it provides less overshoot, and
high dynamics when changing the setpoint. 7-44 Process PID Gain Scale at Max. Ref.
7-38 Process PID Feed Forward Factor is active Range: Function:
when 1-00 Configuration Mode is set to [3]
100 %* [0 - 100 Enter a scaling percentage to apply to the
Process.
%] process PID output when operating at the
maximum reference. The scaling percentage
7-39 On Reference Bandwidth
will be adjusted linearly between the scale
Range: Function: at min. ref. (7-43 Process PID Gain Scale at
5 %* [0 - 200 Enter the On Reference bandwidth. When the Min. Ref.) and the scale at max. ref.
%] PID control error (the difference between the (7-44 Process PID Gain Scale at Max. Ref.).
reference and the feedback) is less than the
set value of this parameter, the On Reference 7-45 Process PID Feed Fwd Resource
status bit is high, i.e., it equals 1. Option: Function:
[0] * No function Select which drive input should be
used as the feed forward factor. The
FF factor is added directly to the
output of the PID controller. This
increases dynamic performance.

3-82 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

7-45 Process PID Feed Fwd Resource 7-51 Process PID Feed Fwd Gain
Option: Function: Range: Function:
[1] Analog input 53 1.00* [0.00 - The feed forward is used to obtain the
[2]
[7]
Analog input 54
Frequency input 29
100.00 ] desired level, based on a well-known signal
available. The PID controller then only takes 3 3
[8] Frequency input 33 care of the smaller part of the control,
[11] Local bus reference necessary because of unknown characters.
[20] Digital pot.meter The standard feed fwd factor in 7-38 Process
PID Feed Forward Factor is always related to
[21] Analog input X30-11
the reference whereas 7-51 Process PID Feed
[22] Analog input X30-12
Fwd Gain has more choices. In winder
[32] Bus PCD Selects a bus reference configured by
applications, the feed fwd factor will typically
8-02 Control Word Source. Change
be the line speed of the system.
8-42 PCD write configuration for the
bus used in order to make the feed-
7-52 Process PID Feed Fwd Ramp up
forward available in 7-48 PCD Feed
Forward. Use index 1 for feed-forward Range: Function:
[748] (and index 2 for reference 0.01 s* [0.01 - 10.00 s] Controls the dynamics of the feed
[1682]). forward signal when ramping up.

7-46 Process PID Feed Fwd Normal/ Inv. Ctrl. 7-53 Process PID Feed Fwd Ramp down
Option: Function: Range: Function:
[0] * Normal Select Normal [0] to set the feed forward factor to 0.01 s* [0.01 - 10.00 s] Controls the dynamics of the feed
treat the FF resource as a positive value. forward signal when ramping down.

[1] Inverse Select Inverse [1] to treat the FF resource as a

7-56 Process PID Ref. Filter Time
negative value.
Range: Function:
7-48 PCD Feed Forward 0.001 s* [0.001 - Set a time constant for the reference first
1.000 s] order low-pass filter. The low-pass filter
Range: Function:
improves steady-state performance and
0* [0 - 65535 ] Read-out parameter where the bus 7-45 Process
dampens oscillations on the reference/
PID Feed Fwd Resource [32] can be read.
feedback signals. However, severe
filtering can be detrimental to dynamic
7-49 Process PID Output Normal/ Inv. Ctrl.
performance.
Option: Function:
[0] * Normal Select Normal [0] to use the resulting output from 7-57 Process PID Fb. Filter Time
the process PID controller as is.
Range: Function:
[1] Inverse Select Inverse [1] to invert the resulting output 0.001 s* [0.001 - Set a time constant for the feedback first
from the process PID controller. This operation is 1.000 s] order low-pass filter. The low-pass filter
performed after the feed forward factor is applied. improves steady-state performance and
dampens oscillations on the reference/
feedback signals. However, severe
3.9.6 7-5* Process PID Ctrl. filtering can be detrimental to dynamic
performance.
Parameter group 7-5* is only used if 1-00 Configuration
Mode is set to [7] Extended PID speed CL or [8] Extended
PID Speed OL.

7-50 Process PID Extended PID

Option: Function:
[0] Disabled Disables the extended parts of the process PID
controller.

[1] * Enabled Enables the extended parts of the PID controller.

MG33MD22 - VLT® is a registered Danfoss trademark 3-83

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.10 Parameters: 8-** Communications and 8-03 Control Word Timeout Time
Options Range: Function:
communication has stopped. The
3.10.1 8-0* General Settings
3 3 function selected in 8-04 Control Word
Timeout Function will then be carried
8-01 Control Site out. The timeout counter is triggered by
Option: Function: a valid control word.
The setting in this parameter overrides
the settings in 8-50 Coasting Select to 8-04 Control Word Timeout Function
8-56 Preset Reference Select. Select the timeout function. The timeout function activates when
the control word fails to be updated within the time period
[0] * Digital and Control by using both digital input and
specified in 8-03 Control Word Timeout Time.
ctrl.word control word.
Option: Function:
[1] Digital only Control by using digital inputs only.
[0] * Off Resumes control via serial bus (Serial
[2] Controlword only Control by using control word only. communication bus or standard) using the
most recent control word.
8-02 Control Word Source
[1] Freeze output Freezes output frequency until communi-
Select the source of the control word: one of two serial interfaces cation resumes.
or four installed options. During initial power-up, the Adjustable
frequency drive automatically sets this parameter to Option A [3] [2] Stop Stops with auto-restart when communi-
if it detects a valid Serial communication bus option installed in cation resumes.
slot A. If the option is removed, the Adjustable frequency drive [3] Jogging Runs the motor at JOG frequency until
detects a change in the configuration, sets 8-02 Control Word communication resumes.
Source back to default setting RS-485, and the Adjustable
[4] Max. speed Runs the motor at maximum frequency
frequency drive then trips. If an option is installed after initial
until communication resumes.
power-up, the setting of 8-02 Control Word Source will not
change but the Adjustable frequency drive will trip and display: [5] Stop and trip Stops the motor, then resets the Adjustable
Alarm 67 Option Changed. frequency drive in order to restart: via the
When you retrofit a bus option into a Adjustable frequency drive Serial communication bus, via the reset
that did not have a bus option installed to begin with, you must button on the LCP or via a digital input.
take an ACTIVE decision to move the control to bus-based. This [7] Select setup 1 Changes the set-up upon reestablishment of
is done for safety reasons in order to avoid an accidental change. communication following a control word
Option: Function: timeout. If communication resumes causing
[0] None the timeout situation to disappear,
[1] FC RS485 8-05 End-of-Timeout Function defines
[2] FC USB whether to resume the set-up used before
[3] * Option A the timeout or to retain the set-up
endorsed by the timeout function.
[4] Option B
[5] Option C0 [8] Select setup 2 See [7] Select setup 1
[6] Option C1 [9] Select setup 3 See [7] Select setup 1
[30] External Can
[10] Select setup 4 See [7] Select setup 1
NOTE! [26] Trip
This parameter cannot be adjusted while the motor is
running. NOTE!
The following configuration is required in order to change
8-03 Control Word Timeout Time the set-up after a timeout:
Set 0-10 Active Set-up to [9] Multi set-up and select the
Range: Function:
relevant link in 0-12 This Set-up Linked to.
1.0 s* [Application Enter the maximum time expected to
dependant] pass between the reception of two
consecutive messages. If this time is
exceeded, it indicates that the serial

3-84 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

8-05 End-of-Timeout Function 8-07 Diagnosis Trigger

Option: Function: Option: Function:
Select the action after receiving a valid Byte Content Description
control word following a timeout. This
parameter is active only when 8-04 Control
0–5 Standard DP
Diagnose
Standard DP Diagnose
Data 3 3
Timeout Function is set to [Set-up 1-4]. Data
[0] Hold set-up Retains the set-up selected in 8-04 Control 6 PDU length Header of extended
Timeout Function and displays a warning, xx diagnostic data
until 8-06 Reset Control Timeout toggles. Then 7 Status type = Header of extended
the Adjustable frequency drive resumes its 0x81 diagnostic data
original set-up. 8 Slot = 0 Header of extended
diagnostic data
[1] * Resume set- Resumes the set-up active prior to the
9 Status info = Header of extended
up timeout.
0 diagnostic data
10–13 VLT VLT warning word
8-06 Reset Control Word Timeout
16-92 Warnin
This parameter is active only when Hold set-up [0] has been
g Word
selected in 8-05 End-of-Timeout Function.
14–17 VLT VLT status word
Option: Function: 16-03 Status
[0] * Do not reset Retains the set-up specified in 8-04 Control Word
Word Timeout Function, following a control 18–21 VLT VLT alarm word
word timeout. 16-90 Alarm
[1] Do reset Returns the Adjustable frequency drive to the Word
original set-up following a control word 22–23 VLT Communication
timeout. The Adjustable frequency drive 9-53 Profibus warning word
performs the reset and then immediately Warning Word (Profibus)
reverts to the Do not reset [0] setting
Enabling diagnosis may cause increased bus
8-07 Diagnosis Trigger traffic. Diagnosis functions are not supported by
Option: Function: all serial communication bus types.

This parameter enables and controls the [0] Disable

Adjustable frequency drive diagnosis function *
and permits expansion of the diagnosis data to [1] Trigger
24 byte. on

NOTE! alarms
[2] Trigger
This is only valid for Profibus.
alarm/
warn.
- Disable [0]: Do not send extended
diagnosis data even if they appear in 8-08 Readout Filtering
the Adjustable frequency drive. The function is used if the speed feedback value readouts on
- Trigger on alarms [1]: Send extended serial communication bus are fluctuating. Select filtered if the
diagnosis data when one or more function is required. A power-cycle is required for changes to
alarms appear in alarm 16-90 Alarm take effect.
Word or 9-53 Profibus Warning Word. Option: Function:
- Trigger alarms/warn. [2]: Send extended [0] * Motor Data Std- Select [0] for normal bus
diagnosis data if one or more alarms or Filt. readouts.
warnings appear in alarm 16-90 Alarm
[1] Motor Data LP- Select [1] for filtered bus
Word, 9-53 Profibus Warning Word, or
Filter readouts of the following
warning 16-92 Warning Word.
parameters:
The content of the extended diagnosis frame is 16-10 Power [kW]
as follows: 16-11 Power [hp]

MG33MD22 - VLT® is a registered Danfoss trademark 3-85

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

8-08 Readout Filtering 8-13 Configurable Status Word STW

The function is used if the speed feedback value readouts on Option: Function:
serial communication bus are fluctuating. Select filtered if the [12] T27 DI status The input will go high whenever T27 has
function is required. A power-cycle is required for changes to
3 3 take effect.
24 V and will go low whenever T27 has 0
V.
Option: Function: [13] T29 DI status The input will go high whenever T29 has
16-12 Motor Voltage 24 V and will go low whenever T29 has 0
16-14 Motor Current V.
16-16 Torque [Nm]
[14] T32 DI status The input will go high whenever T32 has
16-17 Speed [RPM]
24 V and will go low whenever T32 has 0
16-22 Torque [%]
V.
16-25 Torque [Nm] High
[15] T33 DI status The input will go high whenever T33 has
24 V and will go low whenever T33 has 0
3.10.2 8-1* Ctrl. Word Settings V.

[16] T37 DI status The input will go high whenever T37 has
8-10 Control Word Profile
0 V and will go low whenever T37 has 24
Select the interpretation of the control and status words V
corresponding to the installed Serial communication bus. Only
[21] Thermal The thermal warning turns on when the
the selections valid for the Serial communication bus installed in
warning temperature exceeds the limit in the
slot A will be visible in the LCP display.
motor, the Adjustable frequency drive, the
For guidelines in selection of FC profile [0] and PROFIdrive profile
brake resistor, or the thermistor.
[1] please refer to the Serial communication via RS 485 Interface
section. [30] Brake fault Will go high when the brake IGBT is short-
For additional guidelines in the selection of PROFIdrive profile [1], (IGBT) circuited.
ODVA [5] and CANopen DSP 402 [7], please refer to the
[40] Out of ref If Comparator 0 is evaluated as TRUE, the
Instruction Manual for the installed Serial communication bus.
range input will go high. Otherwise, it will be
Option: Function: low.
[0] * FC profile
[60] Comparator 0 If Comparator 0 is evaluated as TRUE, the
[1] PROFIdrive profile
input will go high. Otherwise, it will be
[5] ODVA low.
[7] CANopen DSP 402
[61] Comparator 1 If Comparator 1 is evaluated as TRUE, the
[8] MCO
input will go high. Otherwise, it will be
8-13 Configurable Status Word STW low.
Option: Function: [62] Comparator 2 If Comparator 2 is evaluated as TRUE, the
[0] No function The input is always low. input will go high. Otherwise, it will be
low.
[1] * Profile Default Depended on the profile set in
8-10 Control Profile. [63] Comparator 3 If Comparator 3 is evaluated as TRUE, the
input will go high. Otherwise, it will be
[2] Alarm 68 Only The input will go high whenever Alarm 68
low.
is active and will go low whenever no
alarm 68 is active [64] Comparator 4 If Comparator 4 is evaluated as TRUE, the
input will go high. Otherwise, it will be
[3] Trip excl Alarm The input will go high whenever Trip on
low.
68 other alarms is active, and then Alarm 68
is active. [65] Comparator 5 If Comparator 5 is evaluated as TRUE, the
input will go high. Otherwise, it will be
[10] T18 DI status The input will go high whenever T18 has
low.
24 V and will go low whenever T18 has 0
V. [70] Logic Rule 0 If Logic Rule 0 is evaluated as TRUE, the
input will go high. Otherwise, it will be
[11] T19 DI status The input will go high whenever T19 has
low.
24 V and will go low whenever T19 has 0
V.

3-86 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

8-13 Configurable Status Word STW 8-13 Configurable Status Word STW
Option: Function: Option: Function:
[71] Logic Rule 1 If Logic Rule 1 is evaluated as TRUE, the input will go low whenever the Smart
input will go high. Otherwise, it will be
low.
Logic Action [37] Set dig. out. A low is
executed 3 3
[72] Logic Rule 2 If Logic Rule 2 is evaluated as TRUE, the [86] ATEX ETR cur. Selectable if par. 1-90 is set to [20] or [21].
input will go high. Otherwise, it will be alarm If the alarm 164 ATEX ETR cur.lim.alarm is
low. active, the output will be 1.

[73] Logic Rule 3 If Logic Rule 3 is evaluated as TRUE, the [87] ATEX ETR freq. Selectable if par. 1-90 is set to [20] or [21].
input will go high. Otherwise, it will be alarm If the alarm 166 ATEX ETR freq.lim.alarm is
low. active, the output will be 1.

[74] Logic Rule 4 If Logic Rule 4 is evaluated as TRUE, the [88] ATEX ETR cur. Selectable if par. 1-90 is set to [20] or [21].
input will go high. Otherwise, it will be warning If the alarm 163 ATEX ETR cur.lim.warning
low. is active, the output will be 1.

[75] Logic Rule 5 If Logic Rule 5 is evaluated as TRUE, the [89] ATEX ETR freq. Selectable if par. 1-90 is set to [20] or [21].
input will go high. Otherwise, it will be warning If the warning 165 ATEX ETR
low. freq.lim.warning is active, the output will
be 1.
[80] SL digital out A SL Controller Action. The input will go
high whenever the Smart Logic Action [90] Safe Function
[38] Set dig. out. A high is executed. The active
input will go low whenever the Smart [91] Safe Opt. Reset
Logic Action [32] Set dig. out. A low is req.
executed.
8-14 Configurable Control Word CTW
[81] SL digital out B SL Controller Action. The input will go
Option: Function:
high whenever the Smart Logic Action
[39] Set dig. out. A high is executed. The Selection of control word bit 10 if it is active
input will go low whenever the Smart low or active high
Logic Action [33] Set dig. out. A low is [0] None
executed. [1] * Profile
[82] SL digital out C SL Controller Action. The input will go default
high whenever the Smart Logic Action [2] CTW Valid,
[40] Set dig. out. A high is executed. The active low
input will go low whenever the Smart [3] Safe Option
Logic Action [34] Set dig. out. A low is Reset
executed. [4] PID error When enabled, it inverts the resulting error
inverse from the process PID controller. Available
[83] SL digital out D SL Controller Action. The input will go
only if "Configuration Mode" is set to
high whenever the Smart Logic Action
"Surface Winder," "Extended PID Speed OL"
[41] Set dig. out. A high is executed. The
or "Extended PID Speed CL."
input will go low whenever the Smart
Logic Action [35] Set dig. out. A low is [5] PID reset I When enabled, resets the I-part of the
executed. part process PID controller. Equivalent to
7-40 Process PID I-part Reset. Available only if
[84] SL digital out E SL Controller Action. The input will go
"Configuration Mode" is set to "Surface
high whenever the Smart Logic Action
Winder," "Extended PID Speed OL" or
[42] Set dig. out. A high is executed. The
"Extended PID Speed CL."
input will go low whenever the Smart
Logic Action [36] Set dig. out. A low is [6] PID enable When enabled, enables the extended
executed. process PID controller. Equivalent to
7-50 Process PID Extended PID. Available only
[85] SL digital out F SL Controller Action. The input will go
if "Configuration Mode" is set "Extended PID
high whenever the Smart Logic Action
Speed OL" or "Extended PID Speed CL."
[43] Set dig. out. A high is executed. The

MG33MD22 - VLT® is a registered Danfoss trademark 3-87

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.10.3 8-3* FC Port Settings 8-36 Max Response Delay

Range: Function:
8-30 Protocol Application [Application Specify the maximum

3 3 Option:
[0] * FC
Function:
Communication according to the FC Protocol
dependent* dependant] permissible delay time
between transmitting a
as described in the VLT AutomationDrive request and receiving a
Design Guide, RS485 Installation and Set-up. response. Exceeding this delay
time will cause control word
[1] FC MC Select the protocol for the FC (standard) port.
timeout.
[2] * Modbus RTU
8-37 Max Inter-Char Delay
8-31 Address
Range: Function:
Range: Function:
Application [Application Specify the maximum
Size related* [ 1. - 255. ]
dependent* dependant] permissible time interval
8-32 FC Port Baud Rate between receiving two bytes.
This parameter activates
Option: Function:
timeout if transmission is
[0] 2400 Baud Baud rate selection for the FC (standard) interrupted.
port. This parameter is active only
[1] 4800 Baud when 8-30 Protocol is set to FC
[2] * 9600 Baud MC [1] protocol.
[3] 19200 Baud
[4] 38400 Baud
3.10.4 8-4* FC MC protocol set
[5] 57600 Baud
[6] 76800 Baud
8-40 Telegram selection
[7] 115200 Baud
Option: Function:
8-33 Parity / Stop Bits [1] * Standard telegram 1 Enables use of freely configurable
Option: Function: messages or standard messages for
[0] * Even Parity, 1 Stop Bit the FC port.
[1] Odd Parity, 1 Stop Bit [100] None
[2] No Parity, 1 Stop Bit [101] PPO 1
[3] No Parity, 2 Stop Bits [102] PPO 2
[103] PPO 3
8-34 Estimated cycle time
[104] PPO 4
Range: Function:
[105] PPO 5
0 ms* [0 - In a noisy environments, the interface may [106] PPO 6
1000000 ms] be blocked by due to overload of bad
[107] PPO 7
frames. This parameter specifies the time
[108] PPO 8
between two consecutive frames on the
[200] Custom telegram 1 Enables use of freely configurable
network. If the interface does not detect
messages or standard messages for
valid frames in that time it flushes the
the FC port.
receive buffer.
[202] Custom telegram 3
8-35 Minimum Response Delay
8-41 Parameters for signals
Range: Function:
Option: Function:
10 ms* [Application Specify the minimum delay time
[0] * None This parameter contains a
dependant] between receiving a request and
list of signals available for
transmitting a response. This is used
selection in 8-42 PCD
for overcoming modem turnaround
write configuration and
delays.
8-43 PCD read configu-
ration.

3-88 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

8-41 Parameters for signals 8-41 Parameters for signals

Option: Function: Option: Function:
[15] Readout: actual setup [1621] Torque [%] High Res.
[302]
[303]
Minimum Reference
Maximum Reference
[1622] Torque [%]
[1625] Torque [Nm] High 3 3
[312] Catch up/slow Down Value [1630] DC Link Voltage
[341] Ramp 1 Ramp up Time [1632] Brake Energy /s
[342] Ramp 1 Ramp Down Time [1633] Brake Energy /2 min
[351] Ramp 2 Ramp up Time [1634] Heatsink Temp.
[352] Ramp 2 Ramp down Time [1635] Inverter Thermal
[380] Jog Ramp Time [1638] SL Controller State
[381] Quick Stop Ramp Time [1639] Control Card Temp.
[411] Motor Speed Low Limit [RPM] [1650] External Reference
[412] Motor Speed Low Limit [Hz] [1651] Pulse Reference
[413] Motor Speed High Limit [RPM] [1652] Feedback [Unit]
[414] Motor Speed High Limit [Hz] [1653] Digi Pot Reference
[416] Torque Limit Motor Mode [1657] Feedback [RPM]
[417] Torque Limit Generator Mode [1660] Digital Input
[590] Digital & Relay Bus Control [1661] Terminal 53 Switch Setting
[593] Pulse Out #27 Bus Control [1662] Analog Input 53
[595] Pulse Out #29 Bus Control [1663] Terminal 54 Switch Setting
[597] Pulse Out #X30/6 Bus Control [1664] Analog Input 54
[653] Term 42 Output Bus Ctrl [1665] Analog Output 42 [mA]
[663] Terminal X30/8 Bus Control [1666] Digital Output [bin]
[673] Terminal X45/1 Bus Control [1667] Freq. Input #29 [Hz]
[683] Terminal X45/3 Bus Control [1668] Freq. Input #33 [Hz]
[748] PCD Feed Forward [1669] Pulse Output #27 [Hz]
[890] Bus Jog 1 Speed [1670] Pulse Output #29 [Hz]
[891] Bus Jog 2 Speed [1671] Relay Output [bin]
[1472] Legacy Alarm Word [1672] Counter A
[1473] Legacy Warning Word [1673] Counter B
[1474] Leg. Ext. Status Word [1674] Prec. Stop Counter
[1500] Operating Hours [1675] Analog In X30/11
[1501] Running Hours [1676] Analog In X30/12
[1502] kWh Counter [1677] Analog Out X30/8 [mA]
[1600] Control Word [1678] Analog Out X45/1 [mA]
[1601] Reference [Unit] [1679] Analog Out X45/3 [mA]
[1602] Reference % [1680] Fieldbus CTW 1
[1603] Status Word [1682] Fieldbus REF 1
[1605] Main Actual Value [%] [1684] Comm. Option STW
[1609] Custom Readout [1685] FC Port CTW 1
[1610] Power [kW] [1686] FC Port REF 1
[1611] Power [hp] [1690] Alarm Word
[1612] Motor Voltage [1691] Alarm Word 2
[1613] Frequency [1692] Warning Word
[1614] Motor Current [1693] Warning Word 2
[1615] Frequency [%] [1694] Ext. Status Word
[1616] Torque [Nm] [1860] Digital Input 2
[1617] Speed [RPM] [3310] Sync Factor Master
[1618] Motor Thermal [3311] Sync Factor Slave
[1619] KTY sensor temperature [3401] PCD 1 Write to MCO
[1620] Motor Angle [3402] PCD 2 Write to MCO

MG33MD22 - VLT® is a registered Danfoss trademark 3-89

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

8-41 Parameters for signals 8-42 PCD write configuration

Option: Function: Range: Function:
[3403] PCD 3 Write to MCO written to the selected parameters

3 3 [3404] PCD 4 Write to MCO

[3405] PCD 5 Write to MCO
as data values.

[3406] PCD 6 Write to MCO 8-43 PCD read configuration

[3407] PCD 7 Write to MCO Range: Function:
[3408] PCD 8 Write to MCO Application [0 - 9999 ] Select the parameters to be
[3409] PCD 9 Write to MCO dependent* assigned to PCDs of the messages.
[3410] PCD 10 Write to MCO The number of available PCDs
[3421] PCD 1 Read from MCO depends on the message type.
[3422] PCD 2 Read from MCO PCDs contain the actual data
[3423] PCD 3 Read from MCO values of the selected parameters.
[3424] PCD 4 Read from MCO
[3425] PCD 5 Read from MCO
[3426] PCD 6 Read from MCO
[3427] PCD 7 Read from MCO
[3428] PCD 8 Read from MCO
[3429] PCD 9 Read from MCO
[3430] PCD 10 Read from MCO
[3440] Digital Inputs
[3441] Digital Outputs
[3450] Actual Position
[3451] Commanded Position
[3452] Actual Master Position
[3453] Slave Index Position
[3454] Master Index Position
[3455] Curve Position
[3456] Track Error
[3457] Synchronizing Error
[3458] Actual Velocity
[3459] Actual Master Velocity
[3460] Synchronizing Status
[3461] Axis Status
[3462] Program Status
[3464] MCO 302 Status
[3465] MCO 302 Control
[3470] MCO Alarm Word 1
[3471] MCO Alarm Word 2
[4280] Safe Option Status
[4285] Active Safe Func.
[4286] Safe Option Info

8-42 PCD write configuration

Range: Function:
Application [0 - Select the parameters to be
dependent* 9999 ] assigned to the PCD's messages.
The number of available PCDs
depends on the message type. The
values in the PCDs will then be

3-90 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.10.5 8-5* Digital/Bus 8-52 DC Brake Select

Option: Function:
Parameters for configuring the control word Digital/Bus [2] Logic Activates Start command via the serial
merging. AND communication bus/serial communication port,
AND additionally via one of the digital inputs. 3 3
NOTE! [3] * Logic OR Activates Start command via the serial
These parameters are active only when 8-01 Control Site is communication bus/serial communication port
set to [0] Digital and control word. OR via one of the digital inputs.

8-50 Coasting Select 8-53 Start Select

Option: Function: Option: Function:
Select control of the coasting function via the Select control of the Adjustable frequency drive
terminals (digital input) and/or via the bus. start function via the terminals (digital input)
and/or via the serial communication bus.
[0] Digital Activates Start command via a digital input.
input [0] Digital Activates Start command via a digital input.
[1] Bus Activates Start command via the serial input
communication port or serial communication [1] Bus Activates Start command via the serial
option. communication port or serial communication
option.
[2] Logic AND Activates Start command via the serial
communication bus/serial communication port, [2] Logic Activates Start command via the serial
AND additionally via one of the digital inputs. AND communication bus/serial communication port,
AND additionally via one of the digital inputs.
[3] * Logic OR Activates Start command via the serial
communication bus/serial communication port [3] * Logic OR Activates Start command via the serial
OR via one of the digital inputs. communication bus/serial communication port
OR via one of the digital inputs.
8-51 Quick Stop Select
Select control of the quick stop function via the terminals (digital 8-54 Reversing Select
input) and/or via the bus. Option: Function:
Option: Function: [0] Digital Select control of the Adjustable frequency drive
[0] Digital input input reverse function via the terminals (digital input)
[1] Bus and/or via the Serial communication bus.

[2] Logic AND [1] Bus Activates the Reverse command via the serial
[3] * Logic OR communication port or Serial communication
bus option .
8-52 DC Brake Select
[2] Logic Activates the Reverse command via the Serial
Option: Function:
AND communication bus/serial communication port,
Select control of the DC brake via the terminals AND additionally via one of the digital inputs.
(digital input) and/or via the serial communi-
cation bus. [3] * Logic OR Activates the Reverse command via the Serial
communication bus/serial communication port
NOTE! OR via one of the digital inputs.
Only selection [0] Digital input is available
when 1-10 Motor Construction is set to [1] 8-55 Set-up Select
PM non-salient SPM. Option: Function:
Select control of the Adjustable frequency drive
[0] Digital Activates Start command via a digital input. set-up selection via the terminals (digital input)
input and/or via the serial communication bus.
[1] Bus Activates Start command via the serial
[0] Digital Activates the set-up selection via a digital
communication port or serial communication
input input.
option.

MG33MD22 - VLT® is a registered Danfoss trademark 3-91

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

8-55 Set-up Select 8-58 Profidrive OFF3 Select

Option: Function: Select control of the drive OFF3 selection via the terminals
[1] Bus Activates the set-up selection via the serial (digital input) and/or via the serial communication bus. This
parameter is active only when par. 8-01 Control Site is set to [0]
3 3 communication port or serial communication
option. Digital and control word and par. 8-10 is set to [1] Profidrive
profile.
[2] Logic Activates the set-up selection via the serial
AND communication bus/serial communication port, Option: Function:
AND additionally via one of the digital inputs. [2] Logic AND
[3] * Logic OR
[3] * Logic OR Activate the set-up selection via the serial
communication bus/serial communication port
OR via one of the digital inputs. 3.10.6 8-8* AFD Port Diagnos.

8-56 Preset Reference Select These parameters are used for monitoring the bus
Option: Function: communication via the Adjustable Frequency Drive Port.
Select control of the Adjustable frequency drive 8-80 Bus Message Count
Preset Reference selection via the terminals Range: Function:
(digital input) and/or via the serial communi-
0* [0 - 0 ] This parameter shows the number of valid
cation bus.
messages detected on the bus.
[0] Digital Activates Preset Reference selection via a digital
input input. 8-81 Bus Error Count
[1] Bus Activates Preset Reference selection via the Range: Function:
serial communication port or serial communi- 0* [0 - 0 ] This parameter shows the number of messages
cation option. with faults (e.g., CRC fault), detected on the bus.

[2] Logic AND Activates Preset Reference selection via the

serial communication bus/serial communication
8-82 Slave Messages Rcvd
port, AND additionally via one of the digital Range: Function:
inputs. 0* [0 - 0 ] This parameter shows the number of valid
messages addressed to the slave, sent by the
[3] * Logic OR Activates the Preset Reference selection via the
Adjustable frequency drive.
serial communication bus/serial communication
port OR via one of the digital inputs.
8-83 Slave Error Count
8-57 Profidrive OFF2 Select Range: Function:
Select control of the drive OFF2 selection via the terminals 0* [0 - 0 ] This parameter shows the number of error
(digital input) and/or via the serial communication bus. This messages, which could not be executed by the
parameter is active only when par. 8-01 Control Site is set to [0] Adjustable frequency drive.
Digital and ctrl. word and par. 8-10 is set to [1] Profidrive profile.
Option: Function: 3.10.7 8-9* Bus Jog
[0] Digital input
[1] Bus 8-90 Bus Jog 1 Speed
[2] Logic AND
Range: Function:
[3] * Logic OR
100 RPM* [ 0 - par. 4-13 Enter the jog speed. This is a fixed
8-58 Profidrive OFF3 Select RPM] jog speed activated via the serial
port or serial communication bus
Select control of the drive OFF3 selection via the terminals
option.
(digital input) and/or via the serial communication bus. This
parameter is active only when par. 8-01 Control Site is set to [0]
Digital and control word and par. 8-10 is set to [1] Profidrive
profile.
Option: Function:
[0] Digital input
[1] Bus

3-92 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

8-91 Bus Jog 2 Speed

Range: Function:
200 RPM* [ 0 - par. 4-13 Enter the jog speed. This is a fixed
RPM] jog speed activated via the serial
port or serial communication bus 3 3
option.

MG33MD22 - VLT® is a registered Danfoss trademark 3-93

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.11 Parameters: 9-** Profibus 9-15 PCD Write Configuration

Array [10]
9-00 Setpoint
Option: Function:
Range: Function:
3 3 0* [0 - This parameter receives cyclical reference from
[653]
[663]
Term 42 Output Bus Ctrl
Terminal X30/8 Bus Control
65535 ] a Master Class 2. If the control priority is set to
[673] Terminal X45/1 Bus Control
Master Class 2, the reference for the Adjustable
[683] Terminal X45/3 Bus Control
frequency drive is taken from this parameter,
[748] PCD Feed Forward
whereas the cyclical reference will be ignored.
[890] Bus Jog 1 Speed

9-07 Actual Value [891] Bus Jog 2 Speed

[1680] Fieldbus CTW 1
Range: Function:
[1682] Fieldbus REF 1
0* [0 - 65535 ] This parameter delivers the MAV for a Master
[1685] FC Port CTW 1
Class 2. The parameter is valid if the control
[1686] FC Port REF 1
priority is set to Master Class 2.
[3310] Sync Factor Master
[3311] Sync Factor Slave
9-15 PCD Write Configuration
[3401] PCD 1 Write to MCO
Array [10]
[3402] PCD 2 Write to MCO
Option: Function: [3403] PCD 3 Write to MCO
Select the parameters to [3404] PCD 4 Write to MCO
be assigned to PCD 3 to
[3405] PCD 5 Write to MCO
10 of the messages. The
[3406] PCD 6 Write to MCO
number of available PCDs
[3407] PCD 7 Write to MCO
depends on the message
[3408] PCD 8 Write to MCO
type. The values in PCD 3
[3409] PCD 9 Write to MCO
to 10 will then be written
[3410] PCD 10 Write to MCO
to the selected
parameters as data 9-16 PCD Read Configuration
values. Alternatively,
Array [10]
specify a standard
Profibus message in Option: Function:
9-22 Telegram Selection. Select the parameters to be
assigned to PCD 3 to 10 of
[0] * None
the messages. The number of
[302] Minimum Reference
available PCDs depends on
[303] Maximum Reference
the message type. PCDs 3 to
[312] Catch up/slow Down Value
10 contain the actual data
[341] Ramp 1 Ramp up Time values of the selected
[342] Ramp 1 Ramp Down Time parameters. For standard
[351] Ramp 2 Ramp up Time Profibus messages, see
[352] Ramp 2 Ramp down Time 9-22 Telegram Selection.
[380] Jog Ramp Time
[0] * None
[381] Quick Stop Ramp Time
[15] Readout: actual setup
[411] Motor Speed Low Limit [RPM]
[1472] Legacy Alarm Word
[412] Motor Speed Low Limit [Hz]
[1473] Legacy Warning Word
[413] Motor Speed High Limit [RPM]
[1474] Leg. Ext. Status Word
[414] Motor Speed High Limit [Hz]
[1500] Operating Hours
[416] Torque Limit Motor Mode
[1501] Running Hours
[417] Torque Limit Generator Mode
[1502] kWh Counter
[590] Digital & Relay Bus Control
[1600] Control Word
[593] Pulse Out #27 Bus Control
[1601] Reference [Unit]
[595] Pulse Out #29 Bus Control
[1602] Reference %
[597] Pulse Out #X30/6 Bus Control

3-94 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

9-16 PCD Read Configuration 9-16 PCD Read Configuration

Array [10] Array [10]
Option: Function: Option: Function:
[1603] Status Word
[1605] Main Actual Value [%]
[1679] Analog Out X45/3 [mA]
[1684] Comm. Option STW
3 3
[1609] Custom Readout [1690] Alarm Word
[1610] Power [kW] [1691] Alarm Word 2
[1611] Power [hp] [1692] Warning Word
[1612] Motor Voltage [1693] Warning Word 2
[1613] Frequency [1694] Ext. Status Word
[1614] Motor Current [1860] Digital Input 2
[1615] Frequency [%] [3421] PCD 1 Read from MCO
[1616] Torque [Nm] [3422] PCD 2 Read from MCO
[1617] Speed [RPM] [3423] PCD 3 Read from MCO
[1618] Motor Thermal [3424] PCD 4 Read from MCO
[1619] KTY sensor temperature [3425] PCD 5 Read from MCO
[1620] Motor Angle [3426] PCD 6 Read from MCO
[1621] Torque [%] High Res. [3427] PCD 7 Read from MCO
[1622] Torque [%] [3428] PCD 8 Read from MCO
[1625] Torque [Nm] High [3429] PCD 9 Read from MCO
[1630] DC Link Voltage [3430] PCD 10 Read from MCO
[1632] Brake Energy /s [3440] Digital Inputs
[1633] Brake Energy /2 min [3441] Digital Outputs
[1634] Heatsink Temp. [3450] Actual Position
[1635] Inverter Thermal [3451] Commanded Position
[1638] SL Controller State [3452] Actual Master Position
[1639] Control Card Temp. [3453] Slave Index Position
[1650] External Reference [3454] Master Index Position
[1651] Pulse Reference [3455] Curve Position
[1652] Feedback [Unit] [3456] Track Error
[1653] Digi Pot Reference [3457] Synchronizing Error
[1657] Feedback [RPM] [3458] Actual Velocity
[1660] Digital Input [3459] Actual Master Velocity
[1661] Terminal 53 Switch Setting [3460] Synchronizing Status
[1662] Analog Input 53 [3461] Axis Status
[1663] Terminal 54 Switch Setting [3462] Program Status
[1664] Analog Input 54 [3464] MCO 302 Status
[1665] Analog Output 42 [mA] [3465] MCO 302 Control
[1666] Digital Output [bin] [3470] MCO Alarm Word 1
[1667] Freq. Input #29 [Hz] [3471] MCO Alarm Word 2
[1668] Freq. Input #33 [Hz] [4280] Safe Option Status
[1669] Pulse Output #27 [Hz] [4285] Active Safe Func.
[1670] Pulse Output #29 [Hz] [4286] Safe Option Info
[1671] Relay Output [bin]
[1672] Counter A
[1673] Counter B
[1674] Prec. Stop Counter
[1675] Analog In X30/11
[1676] Analog In X30/12
[1677] Analog Out X30/8 [mA]
[1678] Analog Out X45/1 [mA]

MG33MD22 - VLT® is a registered Danfoss trademark 3-95

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

9-18 Node Address 9-23 Parameters for Signals

Range: Function: Array [1000]
126 * [ 0 - Enter the station address in this parameter or Read only

3 3 126. ] alternatively in the hardware switch. In order

to adjust the station address in 9-18 Node
Option:
[416] Torque Limit Motor Mode
Function:

Address, the hardware switch must be set to [417] Torque Limit Generator Mode
126 or 127 (i.e. all switches set to ‘on’).
[590] Digital & Relay Bus Control
Otherwise this parameter will display the
[593] Pulse Out #27 Bus Control
actual setting of the switch.
[595] Pulse Out #29 Bus Control
[597] Pulse Out #X30/6 Bus Control
9-22 Telegram Selection
[653] Term 42 Output Bus Ctrl
Displays the Profibus telegram configuration.
[663] Terminal X30/8 Bus Control
Option: Function: [673] Terminal X45/1 Bus Control
[1] Standard telegram 1 [683] Terminal X45/3 Bus Control
[100] * None [748] PCD Feed Forward
[101] PPO 1 [890] Bus Jog 1 Speed
[102] PPO 2 [891] Bus Jog 2 Speed
[103] PPO 3 [1472] Legacy Alarm Word
[104] PPO 4 [1473] Legacy Warning Word
[105] PPO 5 [1474] Leg. Ext. Status Word
[106] PPO 6 [1500] Operating Hours
[107] PPO 7 [1501] Running Hours
[108] * PPO 8 Read only. [1502] kWh Counter
[200] Custom telegram 1 [1600] Control Word
[202] Custom telegram 3 [1601] Reference [Unit]
[1602] Reference %
9-23 Parameters for Signals [1603] Status Word
Array [1000] [1605] Main Actual Value [%]
Read only [1609] Custom Readout
Option: Function: [1610] Power [kW]
This parameter contains a [1611] Power [hp]
list of signals available for [1612] Motor Voltage
selection in 9-15 PCD [1613] Frequency
Write Configuration and [1614] Motor Current
9-16 PCD Read Configu- [1615] Frequency [%]
ration. [1616] Torque [Nm]
[0] * None [1617] Speed [RPM]
[15] Readout: actual setup [1618] Motor Thermal
[302] Minimum Reference [1619] KTY sensor temperature
[303] Maximum Reference [1620] Motor Angle
[312] Catch up/slow Down Value [1621] Torque [%] High Res.
[341] Ramp 1 Ramp up Time [1622] Torque [%]
[342] Ramp 1 Ramp Down Time [1625] Torque [Nm] High
[351] Ramp 2 Ramp up Time [1630] DC Link Voltage
[352] Ramp 2 Ramp down Time [1632] Brake Energy /s
[380] Jog Ramp Time [1633] Brake Energy /2 min
[381] Quick Stop Ramp Time [1634] Heatsink Temp.
[411] Motor Speed Low Limit [RPM] [1635] Inverter Thermal
[412] Motor Speed Low Limit [Hz] [1638] SL Controller State
[413] Motor Speed High Limit [RPM] [1639] Control Card Temp.
[414] Motor Speed High Limit [Hz] [1650] External Reference

3-96 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

9-23 Parameters for Signals 9-23 Parameters for Signals

Array [1000] Array [1000]
Read only Read only
Option:
[1651] Pulse Reference
Function: Option:
[3421] PCD 1 Read from MCO
Function:
3 3
[1652] Feedback [Unit] [3422] PCD 2 Read from MCO
[1653] Digi Pot Reference [3423] PCD 3 Read from MCO
[1657] Feedback [RPM] [3424] PCD 4 Read from MCO
[1660] Digital Input [3425] PCD 5 Read from MCO
[1661] Terminal 53 Switch Setting [3426] PCD 6 Read from MCO
[1662] Analog Input 53 [3427] PCD 7 Read from MCO
[1663] Terminal 54 Switch Setting [3428] PCD 8 Read from MCO
[1664] Analog Input 54 [3429] PCD 9 Read from MCO
[1665] Analog Output 42 [mA] [3430] PCD 10 Read from MCO
[1666] Digital Output [bin] [3440] Digital Inputs
[1667] Freq. Input #29 [Hz] [3441] Digital Outputs
[1668] Freq. Input #33 [Hz] [3450] Actual Position
[1669] Pulse Output #27 [Hz] [3451] Commanded Position
[1670] Pulse Output #29 [Hz] [3452] Actual Master Position
[1671] Relay Output [bin] [3453] Slave Index Position
[1672] Counter A [3454] Master Index Position
[1673] Counter B [3455] Curve Position
[1674] Prec. Stop Counter [3456] Track Error
[1675] Analog In X30/11 [3457] Synchronizing Error
[1676] Analog In X30/12 [3458] Actual Velocity
[1677] Analog Out X30/8 [mA] [3459] Actual Master Velocity
[1678] Analog Out X45/1 [mA] [3460] Synchronizing Status
[1679] Analog Out X45/3 [mA] [3461] Axis Status
[1680] Fieldbus CTW 1 [3462] Program Status
[1682] Fieldbus REF 1 [3464] MCO 302 Status
[1684] Comm. Option STW [3465] MCO 302 Control
[1685] FC Port CTW 1 [3470] MCO Alarm Word 1
[1686] FC Port REF 1 [3471] MCO Alarm Word 2
[1690] Alarm Word [4280] Safe Option Status
[1691] Alarm Word 2 [4285] Active Safe Func.
[1692] Warning Word [4286] Safe Option Info
[1693] Warning Word 2
9-27 Parameter Edit
[1694] Ext. Status Word
[1860] Digital Input 2 Option: Function:
[3310] Sync Factor Master Parameters can be edited via Profibus, the
[3311] Sync Factor Slave standard RS485 interface, or the LCP.
[3401] PCD 1 Write to MCO [0] Disabled Disables editing via Profibus.
[3402] PCD 2 Write to MCO
[1] * Enabled Enables editing via Profibus.
[3403] PCD 3 Write to MCO
[3404] PCD 4 Write to MCO
[3405] PCD 5 Write to MCO
[3406] PCD 6 Write to MCO
[3407] PCD 7 Write to MCO
[3408] PCD 8 Write to MCO
[3409] PCD 9 Write to MCO
[3410] PCD 10 Write to MCO

MG33MD22 - VLT® is a registered Danfoss trademark 3-97

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

9-28 Process Control 9-53 Profibus Warning Word

Option: Function: Range: Function:
Process control (setting of the control word, 0* [0 - 65535 ] This parameter displays Profibus communi-

3 3 speed reference, and process data) is possible

via either Profibus or standard serial communi-
cation warnings. Please refer to the Profibus
Instruction Manual for further information.
cation bus but not both simultaneously. Local
control is always possible via the LCP. Control Read only
via process control is possible via either
terminals or serial communication bus Bit: Meaning:
depending on the settings in 8-50 Coasting 0 Connection with DP master is not ok
Select to 8-56 Preset Reference Select. 1 Not used
[0] Disable Disables process control via Profibus, and 2 FDLNDL (Serial Communication Bus Data link Layer) is
enables process control via standard serial not ok
communication bus or Profibus Master class 2. 3 Clear data command received
4 Actual value is not updated
[1] * Enable Enables process control via Profibus Master Class
5 Baudrate search
cyclic 1, and disables process control via standard
master serial communication bus or Profibus Master 6 PROFIBUS ASIC is not transmitting
class 2. 7 Initialization of PROFIBUS is not ok
8 Adjustable frequency drive is tripped
9-44 Fault Message Counter 9 Internal CAN error

Range: Function: 10 Wrong configuration data from PLC

11 Wrong ID sent by PLC
0* [0 - 65535 ] This parameter displays the number of error
12 Internal error occured
events stored in 9-45 Fault Code and 9-47 Fault
Number. The maximum buffer capacity is eight 13 Not configured
error events. The buffer and counter are set to 14 Timeout active
0 upon reset or power-up. 15 Warning 34 active

9-45 Fault Code 9-63 Actual Baud Rate

Range: Function: Option: Function:
0* [0 - 0 ] This buffer contains the alarm word for all alarms This parameter displays the actual
and warnings that have occurred since the last Profibus baud rate. The Profibus
reset or power-up. The maximum buffer capacity is Master automatically sets the baud
eight error events. rate.

[0] 9,6 kbit/s

9-47 Fault Number
[1] 19,2 kbit/s
Range: Function:
[2] 93,75 kbit/s
0* [0 - 0 ] This buffer contains the alarm number (e.g., 2 for
[3] 187,5 kbit/s
live zero error, 4 for line phase loss) for all alarms
[4] 500 kbit/s
and warnings that have occurred since last reset or
[6] 1500 kbit/s
power-up. The maximum buffer capacity is eight
[7] 3000 kbit/s
error events.
[8] 6000 kbit/s

9-52 Fault Situation Counter [9] 12000 kbit/s

[10] 31,25 kbit/s
Range: Function:
[11] 45,45 kbit/s
0* [0 - 1000 ] This parameter displays the number of error
[255] * No baudrate found
events which have occurred since the last reset
of power-up. 9-64 Device Identification
Range: Function:
0* [0 - 0 ] This parameter displays the device identification.
Please refer to the Instruction Manual for Profibus,
MG.33.CX.YY for further explanation.

3-98 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

9-65 Profile Number 9-71 Profibus Save Data Values

Range: Function: Option: Function:
0* [0 - 0 ] This parameter contains the profile identification. [2] Store all Stores all parameter values for all set-ups in the
Byte 1 contains the profile number and byte 2 the
version number of the profile.
setups non-volatile memory. The selection returns to
Off [0] when all parameter values have been 3 3
stored.
NOTE!
This parameter is not visible via LCP. 9-72 ProfibusDriveReset
Option: Function:
9-67 Control Word 1 [0] * No action
Range: Function: [1] Power-on Resets Adjustable frequency drive upon
reset power-up, as for power-cycle.
0* [0 - 65535 ] This parameter accepts the control word from
a Master Class 2 in the same format as PCD 1. [3] Comm Resets the Profibus option only, useful after
option reset changing certain settings in parameter
9-68 Status Word 1 group 9-**, e.g., 9-18 Node Address.
Range: Function: When reset, the Adjustable frequency drive
disappears from the serial communication
0* [0 - 65535 ] This parameter delivers the status word for a
bus, which may cause a communication
Master Class 2 in the same format as PCD 2.
error from the master.

9-70 Programming Set-up

9-75 DO Identification
Option: Function:
Range: Function:
Select the set-up to be edited.
0* [0 - 65535 ] Provides information about the DO (Drive
[0] Factory setup Uses default data. This option can be used Object).
as a data source to return the other set-ups
to a known state. 9-80 Defined Parameters (1)
[1] Set-up 1 Edits Set-up 1. Array [116]
[2] Set-up 2 Edits Set-up 2. No LCP access
Read only
[3] Set-up 3 Edits Set-up 3.
Range: Function:
[4] Set-up 4 Edits Set-up 4. 0* [0 - 9999 ] This parameter displays a list of all the defined
[9] * Active Set-up Follows the active set-up selected in Adjustable frequency drive parameters available
0-10 Active Set-up. for Profibus.

This parameter is unique to LCP and serial communication 9-81 Defined Parameters (2)
busses. See also 0-11 Programming Set-up. Array [116]
9-71 Profibus Save Data Values No LCP access
Read only
Option: Function:
Parameter values changed via Profibus are not
Range: Function:
automatically stored in non-volatile memory. 0* [0 - 9999 ] This parameter displays a list of all the defined
Use this parameter to activate a function that Adjustable frequency drive parameters available
stores parameter values in the EEPROM non- for Profibus.
volatile memory, so changed parameter values
will be retained at power-down. 9-82 Defined Parameters (3)
Array [116]
[0] * Off Deactivates the non-volatile storage function.
No LCP access
[1] Store all Stores all parameter values for all set-ups in the Read only
setups non-volatile memory. The selection returns to
Range: Function:
Off [0] when all parameter values have been
0* [0 - 9999 ] This parameter displays a list of all the defined
stored.
Adjustable frequency drive parameters available
for Profibus.

MG33MD22 - VLT® is a registered Danfoss trademark 3-99

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

9-83 Defined Parameters (4)

Array [116]
No LCP access
Read only
3 3 Range: Function:
0* [0 - 9999 ] This parameter displays a list of all the defined
Adjustable frequency drive parameters available
for Profibus.

9-84 Defined Parameters (5)

Range: Function:
0* [0 - 9999 ] This parameter displays a list of all the defined
Adjustable frequency drive parameters available
for Profibus.

9-90 Changed Parameters (1)

Array [116]
No LCP access
Read only
Range: Function:
0* [0 - 9999 ] This parameter displays a list of all the
Adjustable frequency drive parameters
deviating from default setting.

9-91 Changed Parameters (2)

Array [116]
No LCP access
Read only
Range: Function:
0* [0 - 9999 ] This parameter displays a list of all the
Adjustable frequency drive parameters
deviating from default setting.

9-92 Changed Parameters (3)

Array [116]
No LCP access
Read only
Range: Function:
0* [0 - 9999 ] This parameter displays a list of all the
Adjustable frequency drive parameters
deviating from default setting.

9-94 Changed Parameters (5)

Array [116]
No LCP Address
Read only
Range: Function:
0* [0 - 9999 ] This parameter displays a list of all the
Adjustable frequency drive parameters
deviating from default setting.

3-100 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.12 Parameters: 10-** DeviceNet CAN 3.12.2 10-1* DeviceNet

Fieldbus
10-10 Process Data Type Selection
3.12.1 10-0* Common Settings Option: Function:
Select the Instance (message) for data
3 3
10-00 CAN Protocol transmission. The instances available are
Option: Function: dependent upon the setting of 8-10 Control
[0] CANopen Profile.
[1] * DeviceNet View the active CAN protocol. When 8-10 Control Profile is set to [0] FC
profile, 10-10 Process Data Type Selection
NOTE! options [0] and [1] are available.
The options depend on installed option. When 8-10 Control Profile is set to [5] ODVA,
10-10 Process Data Type Selection options [2]
and [3] are available.
10-01 Baud Rate Select
Instances 100/150 and 101/151 are Danfoss-
Select the serial communication bus transmission speed. The specific. Instances 20/70 and 21/71 are
selection must correspond to the transmission speed of the ODVA-specific AC Drive profiles.
master and the other serial communication bus nodes. For guidelines in message selection, please
Option: Function: refer to the DeviceNet Instruction Manual.
[16] 10 Kbps Note that a change to this parameter will
[17] 20 Kbps be executed immediately.
[18] 50 Kbps [0] * INSTANCE
[19] 100 Kbps 100/150
[20] * 125 Kbps [1] INSTANCE
[21] 250 Kbps 101/151
[22] 500 Kbps [2] INSTANCE
20/70
10-02 MAC ID [3] INSTANCE
Range: Function: 21/71
Application [Application Selection of station address.
dependent* dependant] Every station connected to
10-11 Process Data Config Write
the same network must have Select the process write data for I/O assembly instances 101/151.
an unambiguous address. Elements [2] and [3] of this array can be selected. Elements [0]
and [1] of the array are fixed.
10-05 Readout Transmit Error Counter Option: Function:
Range: Function: [0] * None
0* [0 - 255 ] View the number of CAN control transmission [302] Minimum Reference
errors since the last power-up. [303] Maximum Reference
[312] Catch up/slow Down Value
10-06 Readout Receive Error Counter [341] Ramp 1 Ramp up Time
Range: Function: [342] Ramp 1 Ramp Down Time
0* [0 - 255 ] View the number of CAN control receipt errors [351] Ramp 2 Ramp up Time
since the last power-up. [352] Ramp 2 Ramp down Time
[380] Jog Ramp Time
10-07 Readout Bus Off Counter [381] Quick Stop Ramp Time
Range: Function: [411] Motor Speed Low Limit [RPM]
0* [0 - 255 ] View the number of Bus Off events since the last [412] Motor Speed Low Limit [Hz]
power-up. [413] Motor Speed High Limit [RPM]
[414] Motor Speed High Limit [Hz]
[416] Torque Limit Motor Mode
[417] Torque Limit Generator Mode
[590] Digital & Relay Bus Control

MG33MD22 - VLT® is a registered Danfoss trademark 3-101

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

10-11 Process Data Config Write 10-12 Process Data Config Read
Select the process write data for I/O assembly instances 101/151. Select the process read data for I/O assembly instances 101/151.
Elements [2] and [3] of this array can be selected. Elements [0] Elements [2] and [3] of this array can be selected. Elements [0]
and [1] of the array are fixed. and [1] of the array are fixed.
3 3 Option: Function: Option: Function:
[593] Pulse Out #27 Bus Control [1610] Power [kW]
[595] Pulse Out #29 Bus Control [1611] Power [hp]
[597] Pulse Out #X30/6 Bus Control [1612] Motor Voltage
[653] Term 42 Output Bus Ctrl [1613] Frequency
[663] Terminal X30/8 Bus Control [1614] Motor Current
[673] Terminal X45/1 Bus Control [1615] Frequency [%]
[683] Terminal X45/3 Bus Control [1616] Torque [Nm]
[748] PCD Feed Forward [1617] Speed [RPM]
[890] Bus Jog 1 Speed [1618] Motor Thermal
[891] Bus Jog 2 Speed [1619] KTY sensor temperature
[1680] Fieldbus CTW 1 [1620] Motor Angle
[1682] Fieldbus REF 1 [1621] Torque [%] High Res.
[1685] FC Port CTW 1 [1622] Torque [%]
[1686] FC Port REF 1 [1625] Torque [Nm] High
[3310] Sync Factor Master [1630] DC Link Voltage
[3311] Sync Factor Slave [1632] Brake Energy /s
[3401] PCD 1 Write to MCO [1633] Brake Energy /2 min
[3402] PCD 2 Write to MCO [1634] Heatsink Temp.
[3403] PCD 3 Write to MCO [1635] Inverter Thermal
[3404] PCD 4 Write to MCO [1638] SL Controller State
[3405] PCD 5 Write to MCO [1639] Control Card Temp.
[3406] PCD 6 Write to MCO [1650] External Reference
[3407] PCD 7 Write to MCO [1651] Pulse Reference
[3408] PCD 8 Write to MCO [1652] Feedback [Unit]
[3409] PCD 9 Write to MCO [1653] Digi Pot Reference
[3410] PCD 10 Write to MCO [1657] Feedback [RPM]
[1660] Digital Input
10-12 Process Data Config Read
[1661] Terminal 53 Switch Setting
Select the process read data for I/O assembly instances 101/151. [1662] Analog Input 53
Elements [2] and [3] of this array can be selected. Elements [0]
[1663] Terminal 54 Switch Setting
and [1] of the array are fixed.
[1664] Analog Input 54
Option: Function: [1665] Analog Output 42 [mA]
[0] * None [1666] Digital Output [bin]
[15] Readout: actual setup [1667] Freq. Input #29 [Hz]
[1472] Legacy Alarm Word [1668] Freq. Input #33 [Hz]
[1473] Legacy Warning Word [1669] Pulse Output #27 [Hz]
[1474] Leg. Ext. Status Word [1670] Pulse Output #29 [Hz]
[1500] Operating Hours [1671] Relay Output [bin]
[1501] Running Hours [1672] Counter A
[1502] kWh Counter [1673] Counter B
[1600] Control Word [1674] Prec. Stop Counter
[1601] Reference [Unit] [1675] Analog In X30/11
[1602] Reference % [1676] Analog In X30/12
[1603] Status Word [1677] Analog Out X30/8 [mA]
[1605] Main Actual Value [%] [1678] Analog Out X45/1 [mA]
[1609] Custom Readout [1679] Analog Out X45/3 [mA]

3-102 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

10-12 Process Data Config Read 10-13 Warning Parameter

Select the process read data for I/O assembly instances 101/151. Range: Function:
Elements [2] and [3] of this array can be selected. Elements [0] Bit: Meaning:
and [1] of the array are fixed.
Option: Function:
0
1
BusNetwork not active
Explicit connection timeout 3 3
[1684] Comm. Option STW 2 I/O connection
[1690] Alarm Word 3 Retry limit reached
[1691] Alarm Word 2 4 Actual is not updated
[1692] Warning Word 5 CAN bus off
[1693] Warning Word 2 6 I/O send error
[1694] Ext. Status Word 7 Initialization error
[1860] Digital Input 2 8 No bus supply
[3421] PCD 1 Read from MCO 9 Bus off
[3422] PCD 2 Read from MCO 10 Error passive
[3423] PCD 3 Read from MCO 11 Error warning
[3424] PCD 4 Read from MCO 12 Duplicate MAC ID Error
[3425] PCD 5 Read from MCO 13 RX queue overrun
[3426] PCD 6 Read from MCO 14 TX queue overrun
[3427] PCD 7 Read from MCO 15 CAN overrun
[3428] PCD 8 Read from MCO
[3429] PCD 9 Read from MCO
[3430] PCD 10 Read from MCO 10-14 Net Reference
[3440] Digital Inputs Read only from LCP
[3441] Digital Outputs Option: Function:
[3450] Actual Position Select the reference source in instance 21/71 and
[3451] Commanded Position 20/70.
[3452] Actual Master Position
[0] * Off Enables reference via analog/digital inputs.
[3453] Slave Index Position
[1] On Enables reference via the serial communication bus.
[3454] Master Index Position
[3455] Curve Position
10-15 Net Control
[3456] Track Error
[3457] Synchronizing Error Read only from LCP

[3458] Actual Velocity Option: Function:

[3459] Actual Master Velocity Select the control source in Instance 21/71 and 20/70.
[3460] Synchronizing Status [0] * Off Enables control via analog/digital inputs.
[3461] Axis Status
[1] On Enable control via the serial communication bus.
[3462] Program Status
[3464] MCO 302 Status
[3465] MCO 302 Control 3.12.3 10-2* COS Filters
[3470] MCO Alarm Word 1
[3471] MCO Alarm Word 2 10-20 COS Filter 1
[4280] Safe Option Status
Range: Function:
[4285] Active Safe Func.
0* [0 - 65535 ] Enter the value for COS Filter 1 to set up the
[4286] Safe Option Info
filter mask for the status word. When operating
10-13 Warning Parameter in COS (Change-Of-State), this function filters
out bits in the status word that should not be
Range: Function:
sent if they change.
0* [0 - View a DeviceNet-specific warning word. One bit
65535 ] is assigned to every warning. Please refer to the
DeviceNet Instruction Manual (MG.33.DX.YY) for
further information.

MG33MD22 - VLT® is a registered Danfoss trademark 3-103

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

10-21 COS Filter 2 10-31 Store Data Values

Range: Function: Option: Function:
0* [0 - 65535 ] Enter the value for COS Filter 2, to set up the Off [0] when all parameter values have been

3 3 filter mask for the Main Actual Value. When

operating in COS (Change-Of-State), this
stored.

function filters out bits in the Main Actual 10-32 Devicenet Revision
Value that should not be sent if they change. Range: Function:
Application [0 - 65535 ] View the DeviceNet revision
10-22 COS Filter 3 dependent* number. This parameter is used
Range: Function: for EDS file creation.
0* [0 - 65535 ] Enter the value for COS Filter 3, to set up the
Application [0 - 65535 ] View the DeviceNet revision
filter mask for PCD 3. When operating in COS
dependent* number. This parameter is used
(Change-Of-State), this function filters out bits
for EDS file creation.
in PCD 3 that should not be sent if they
change.
10-33 Store Always
Option: Function:
10-23 COS Filter 4
[0] * Off Deactivates non-volatile storage of data.
Range: Function:
0* [0 - 65535 ] Enter the value for COS Filter 4 to set up the [1] On Stores parameter data received via DeviceNet in
filter mask for PCD 4. When operating in COS EEProm non-volatile memory as default.
(Change-Of-State), this function filters out bits
in PCD 4 that should not be sent if they 10-39 Devicenet F Parameters
change. Array [1000]
No LCP access
Range: Function:
3.12.4 10-3* Parameter Access
0* [0 - 0 ] This parameter is used to configure the Adjustable
frequency drive via DeviceNet and build the EDS
Parameter group providing access to indexed parameters
file.
and defining programming set-up.

10-30 Array Index

Range: Function:
0* [0 - 255 ] View array parameters. This parameter is valid
only when a DeviceNet serial communication bus
is installed.

10-31 Store Data Values

Option: Function:
Parameter values changed via DeviceNet are
not automatically stored in non-volatile
memory. Use this parameter to activate a
function that stores parameter values in the
EEPROM non-volatile memory, so that changed
parameter values will be retained at power-
down.

[0] * Off Deactivates the non-volatile storage function.

[1] Store all Stores all parameter values from the active set-
setups up in the non-volatile memory. The selection
returns to Off [0] when all values have been
stored.

[2] Store all Stores all parameter values for all set-ups in the
setups non-volatile memory. The selection returns to

3-104 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.13 Parameters: 12-** Ethernet 12-07 Domain Name

Range: Function:
3.13.1 12-0* IP Settings
Blank [0–19 characters] Domain name of the attached

12-00 IP Address Assignment

network. Can be automatically
assigned when using DHCP. 3 3
Option: Function:
12-08 Host Name
Selects the IP address assignment method.
[0] * Manual IP-address can be set in12-01 IP Address IP Address. Range: Function:
[1] DHCP The IP address is assigned via DHCP server. Blank [0–19 characters] Logical (given) name of option.
[2] BOOTP The IP address is assigned via BOOTP server.
12-09 Physical Address
12-01 IP Address Range: Function:
Range: Function: [00:1B:08:00:00:00–00:1B: Read only: Displays the Physical
[000.000.000.000– Configure the IP address of the 08:FF:FF:FF] (MAC) address of the option.
255.255.255.255] option. Read-only if 12-00 IP Address
Assignment set to DHCP or BOOTP. 3.13.2 12-1* Ethernet Link Parameters
12-02 Subnet Mask
12-1* Ethernet link parameters
Range: Function:
Option: Function:
[000.000.000.000– Configure the IP subnet mask of the
Applies for whole parameter group.
255.255.255.255] option. Read-only if 12-00 IP Address
Assignment set to DHCP or BOOTP. [0] Port 1
[1] Port 2
12-03 Default Gateway
12-10 Link Status
Range: Function:
Option: Function:
[000.000.000.000 – Configure the IP default gateway of
255.255.255.255] the option. Read-only if 12-00 IP Read only. Displays the link status of the Ethernet
Address Assignment set to DHCP or ports.
BOOTP. [0] No link
[1] Link
12-04 DHCP Server
Range: Function: 12-11 Link Duration
[000.000.000.000– Read only. Displays the IP address Option: Function:
255.255.255.255] of the found DHCP or BOOTP Link Duration Port 1 Read only. Displays the duration of
server. (dd:hh:mm:ss) the present link on each port in
dd:hh:mm:ss.
NOTE!
A power cycle is necessary after setting the IP parameters 12-12 Auto Negotiation
manually. Option: Function:
Configures Auto Negotiation of Ethernet link
12-05 Lease Expires parameters, for each port: ON or OFF.

Range: Function: [0] Off Link Speed and Link Duplex can be configured in
12-13 Link Speed and 12-14 Link Duplex.
[dd:hh:mm:ss] Read only. Displays the lease time left for the
[1] On
current DHCP-assigned IP address.
12-13 Link Speed
12-06 Name Servers
Option: Function:
Option: Function:
Forces the link speed for each port at 10 or 100
IP addresses of Domain Name Servers. Can
Mbps. If 12-12 Auto Negotiation is set to: ON,
be automatically assigned when using DHCP.
this parameter is read only and displays the
[0] Primary DNS
actual link speed. “None” is displayed if no link
[1] Secondary DNS
is present.
[0] * None
[1] 10 Mbps

MG33MD22 - VLT® is a registered Danfoss trademark 3-105

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

12-13 Link Speed 12-27 Primary Master

Option: Function: Range: Function:
[2] 100 Mbps 0* [0 - Controls the master’s access to the process

3 3 12-14 Link Duplex

4294967295 ] data. The value zero (0.0.0.0) means that
other masters can take control of the drive
Option: Function: immediately if the connection is lost or
Forces the duplex for each port to full or half closed. Setting an IP number means that
duplex. If 12-12 Auto Negotiation is set to: ON, only a master with this value can establish
this parameter is read-only. a connection for controlling the drive. In
[0] Half duplex systems with backup masters, this
[1] * Full duplex parameter should be left to the value zero
(0.0.0.0).

3.13.3 12-2* Process Data

12-28 Store Data Values
Option: Function:
12-20 Control Instance
This parameter activates a function that stores
Range: Function:
all parameter values in the non-volatile
[None, 20, 21, 100, Read only. Displays the originator-to- memory (EEPROM) thus retaining parameter
101, 103] target connection point. If no CIP values at power-down.
connection is present, “None” is The parameter returns to “Off”.
displayed.
[0] * Off The store function is inactive.
12-21 Process Data Config Write [1] Store all All parameter value will be stored in the non-
set-ups volatile memory in all four set-ups.
Range: Function:
[[0–9] PCD read 0–9] Configuration of readable process data. 12-29 Store Always
Option: Function:
NOTE!
Activates function that will always store received
To configure 2-word (32-bit) parameters for read/write, use
parameter data in non-volatile memory (EEPROM).
two consecutive arrays in 12-21 Process Data Config Write
and 12-22 Process Data Config Read. [0] * Off
[1] On

12-22 Process Data Config Read

Range: Function:
[[0–9] PCD read 0–9] Configuration of readable process data.

12-23 Process Data Config Write Size

Range: Function:
16* [1 - 32 ] Sets the number of bits being sent from the drive
as process data. The setting counts from right
(LSB). The value 1 means that only the least
significant bit of the signal will be transferred
from the drive.

12-24 Process Data Config Read Size

Range: Function:
16* [1 - 32 ] Sets the number of bits being sent to the drive
as process data. The setting counts from right
(LSB). The value 1 means that only the least
significant bit of the signal will be transferred to
the drive. The preceding bits will be set to zero.

3-106 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.13.4 12-3* EtherNet/IP 12-37 COS Inhibit Timer

Range: Function:
12-30 Warning parameter [0–65.535 Read-only Change-Of-State inhibit timer. If the
Range:
[0000–
Function:
Read only. Displays the EtherNet/IP specific 16-bit
ms] option is configured for COS operation, this
inhibit timer can be configured in the Forward 3 3
FFFF hex] status word. Open message to prevent that continuously
changing PCD data generates extensive network
Bit Description traffic. The inhibit time is in milliseconds, 0 =
0 Owned disabled.
1 Not used
12-38 COS Filters
2 Configured
3 Not used Range: Function:
4 Not used [[0–9] Filter 0–9 Change-Of-State PCD filters. Sets up a
5 Not used (0000–FFFFhex)] filter mask for each word of process data
6 Not used when operating in COS mode. Single bits
7 Not used in the PCDs can be filtered in/out.

8 Minor recoverable fault 12-50 Configured Station Alias

9 Minor unrecoverable fault
Range: Function:
10 Major recoverable fault
0* [0 - 65535 ] The parameter shows the configured EtherCAT
11 Major unrecoverable fault
station alias for the Adjustable frequency drive.
12 Not used
Changes will first be active after a power cycle.
13 Not used
14 Not used 12-51 Configured Station Address
15 Not used
Range: Function:
0* [0 - 65535 ] The parameter shows the configured station
12-31 Net Reference address. The parameter can only be set by the
master at power-up.
Option: Function:
Read only. Displays the reference source in Instance
12-59 EtherCAT Status
21/71.
Range: Function:
[0] * Off Reference from the network is not active.
0* [0 - 4294967295 ] This parameter contains status
[1] On Reference from the network is active.
information on the EtherCAT interface.
12-32 Net Control Refer to the EtherCAT manual for
Option: Function: detailed information.

Read only. Displays the control source in Instance

12-80 FTP Server
21/71.
[0] * Off Control via the network is not active. Option: Function:
[1] On Control via the network is active [0] * Disable Disables the built-in FTP server.
[1] Enable Enables the built-in FTP server.
12-33 CIP Revision
Option: Function: 12-81 HTTP Server
Read only. Displays the CIP version of Option: Function:
the option software. [0] * Disable Disables the built-in HTTP (web) server.
[0] Major version (00–99) [1] Enable Enables the built-in HTTP (web) server.
[1] Minor version (00–99)
12-82 SMTP Service
12-34 CIP Product Code Option: Function:
Range: Function: [0] * Disable Disables the SMTP (e-mail) service on the option.
1100 (FC 302) 1110 [0 – 9999] Read only. Displays the CIP [1] Enable Enables the SMTP (e-mail) service on the option.
(FC 301)* product code.

MG33MD22 - VLT® is a registered Danfoss trademark 3-107

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

12-89 Transparent Socket Channel Port 12-93 Cable Error Length

Range: Function: Option: Function:
0* [0 – 9999] Configures the TCP port number for the [0] Error length

3 3 transparent socket channel. This enables FC

messages to be sent transparently on Ethernet
Port 1 (0–656 ft
[0–200 m])
via TCP. Default value is 4000, 0 means disabled. [1] Error length
Port 2 (0–656 ft
12-90 Cable Diagnostics
[0–200 m])
Option: Function:
Enables/disables advanced cable diagnosis 12-94 Broadcast Storm Protection
function. If enabled, the distance to cable errors Option: Function:
can be read out in 12-93 Cable Error Length. The The built-in switch is capable of protecting
parameter resumes to the default setting of the switch system from receiving too many
Disable after the diagnostics have finished. broadcast packages, which can use up
[0] * Disable network resources. The value indicates a
[1] Enable percentage of the total bandwidth that is
allowed for broadcast messages.
NOTE! Example:
The cable diagnostics function will only be issued on ports The “OFF” means that the filter is disabled,
where there is no link (see 12-10 Link Status, Link Status) and all broadcast messages will be passed
through. The value “0%” means that no
12-91 Auto Cross-Over broadcast messages will be passed through.
A value of “10%” means that 10% of the
Option: Function:
total bandwidth is allowed for broadcast
[0] Disable Disables the auto cross-over function.
messages. If the amount of broadcast
[1] * Enable Enables the auto cross-over function.
messages increases above the 10%
NOTE! threshold, they will be blocked.

Disabling of the auto cross-over function will require [0] Protection

crossed Ethernet cables for daisy-chaining the options. Value Port 1
(*Off – 20%)
[1] Protection
12-92 IGMP Snooping
Value Port 2
Option: Function: (*Off – 20%)
This prevents flooding of the Ethernet protocol
stack by only forwarding multicast packets to ports 12-95 Broadcast Storm Filter
that are a member of the multicast group Option: Function:
[0] Disable Disables the IGMP snooping function. Applies to 12-94 Broadcast Storm
[1] * Enable Enables the IGMP snooping function. Protection; if Broadcast Storm
Protection should also include
12-93 Cable Error Length Multicast messages.
Option: Function: [0] Broadcast only
If Cable Diagnostics is enabled in 12-90, the [1] Broadcast &
built-in switch is able via Time Domain Multicast
Reflectometry (TDR). This is a measurement
technique which detects common cabling 12-96 Port Config
problems such as open circuits, short Enables/disables port mirroring function. For troubleshooting
circuits and impedance mismatches or with a network analyzer tool.
breaks in transmission cables. The distance Option: Function:
from the option to the error is displayed in
[0] * Normal No port mirroring
meters [feet] with an accuracy of +/- 2 m
[6.5 ft]. The value 0 means no errors [1] Mirror Port 1 to 2 All network traffic on port 1 will
detected. be mirrored to port 2.

3-108 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

12-96 Port Config

Enables/disables port mirroring function. For troubleshooting
with a network analyzer tool.
Option:
[2] Mirror Port 2 to 1
Function:
All network traffic on port 2 will
3 3
be mirrored to port 1.

[254] Mirror Int. Port to 1

[255] Mirror Int. Port to 2

12-98 Interface Counters

Option: Function:
Read only. Advanced interface
counters from the built-in switch
can be used for low-level trouble-
shooting. The parameter shows
the sum of port 1 + port 2.
[0] In Octets
[1] In Unicast Packets
[2] In Non-Unicast Packets
[3] In Discards
[4] In Errors
[5] In Unknown Protocols
[6] Out Octets
[7] Out Unicast Packets
[8] Out Non-Unicast Packets
[9] Out Discards
[10] Out Errors

12-99 Media Counters

Option: Function:
Read only. Advanced interface
counters from the built-in switch can
be used for low-level troubleshooting.
The parameter shows the sum of port
1 + port 2.
[0] Alignment Errors
[1] FCS Errors
[2] Single Collisions
[3] Multiple Collisions
[4] SQE Test Errors
[5] Deferred Errors
[6] Late Collisions
[7] Excessive Collisions
[8] MAC Transmit Errors
[9] Carrier Sense Errors
[10] Frame Too Long
[11] MAC Receive Errors

MG33MD22 - VLT® is a registered Danfoss trademark 3-109

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.14 Parameters: 13-** Smart Logic Control

3.14.1 Prog. Features

3 3 Smart Logic Control (SLC) is essentially a sequence of user-

defined actions (see 13-52 SL Controller Action [x]) executed
by the SLC when the associated user-defined event (see
13-51 SL Controller Event [x]) is evaluated as TRUE by the
SLC .
The condition for an event can be a particular status or
that the output from a logic rule or a comparator operand
becomes TRUE. That will lead to an associated action as
illustrated:

Par. 13-51 Par. 13-51

130BB671.10

SL Controller Event SL Controller Action

Running
Starting and stopping the SLC:
Coast
Warning Start timer Starting and stopping the SLC can be done by
Torque limit Set Do X low selecting .On [1]. or .Off [0]. in 13-00 SL Controller Mode.
Digital inpute X 30/2 Select set-up 2
... ... The SLC always starts in state 0 (where it evaluates event
[0]). The SLC starts when the Start Event (defined in
Par. 13-43 13-01 Start Event) is evaluated as TRUE (provided that On
Logic Rule Operator 2
[1] is selected in 13-00 SL Controller Mode). The SLC stops
when the Stop Event (13-02 Stop Event) is TRUE. 13-03 Reset
SLC resets all SLC parameters and start programming from
... scratch.
...

Par. 13-43 3.14.2 13-0* SLC Settings

Comparator Operator

Use the SLC settings to activate, deactivate and reset the

=
TRUE longer than.. Smart Logic Control sequence. The logic functions and
comparators are always running in the background, which
...
... opens for separate control of digital inputs and outputs.

13-00 SL Controller Mode

Option: Function:
Events and actions are each numbered and linked together [0] Off Disables the Smart Logic Controller.
in pairs (states). This means that when event [0] is fulfilled
[1] On Enables the Smart Logic Controller.
(attains the value TRUE), action [0] is executed. After this,
the conditions of event [1] will be evaluated and if
13-01 Start Event
evaluated TRUE, action [1] will be executed and so on.
Option: Function:
Only one event will be evaluated at any time. If an event is
evaluated as FALSE, nothing happens (in the SLC) during [0] * False Select the Boolean (TRUE or FALSE)
the current scan interval and no other events will be input to activate Smart Logic Control.
evaluated. This means that when the SLC starts, it False [0] enters the fixed value - FALSE
evaluates event [0] (and only event [0]) each scan interval. [1] True True [1] enters the fixed value - TRUE.
Only when event [0] is evaluated TRUE, will the SLC
[2] Running Running [2] The motor is running.
execute action [0] and start evaluating event [1]. It is
possible to program from 1 to 20 events and actions. [3] In range In range [3] The motor is running
When the last event / action has been executed, the within the programmed current and
sequence starts over again from event [0] / action [0]. The speed ranges set in 4-50 Warning
figure shows an example with three events/actions: Current Low to 4-53 Warning Speed
High.

3-110 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

13-01 Start Event 13-01 Start Event

Option: Function: Option: Function:
[4] On reference On reference [4] The motor is running [18] Reversing Reverse [18] The output is high when

[5] Torque limit

on reference.

Torque limit [5] The torque limit, set in

the Adjustable frequency drive is
running counter clockwise (the logical 3 3
product of the status bits “running”
4-16 Torque Limit Motor Mode or
AND “reverse”).
4-17 Torque Limit Generator Mode, has
been exceeded. [19] Warning Warning [19] A warning is active.

[6] Current limit Current limit [6] The motor current [20] Alarm (trip) Alarm (trip) [20] A (trip) alarm is active.
limit, set in 4-18 Current Limit, has been
[21] Alarm (trip lock) Alarm (trip lock) [21] A (Trip lock) alarm
exceeded.
is active.
[7] Out of current Out of current range [7] The motor
[22] Comparator 0 Comparator 0 [22] Use the result of
range current is outside the range set in
comparator 0.
4-18 Current Limit.
[23] Comparator 1 Comparator 1 [23] Use the result of
[8] Below I low Below I low [8] The motor current is
comparator 1.
lower than set in 4-50 Warning Current
Low. [24] Comparator 2 Comparator 2 [24] Use the result of
comparator 2.
[9] Above I high Above I high [9] The motor current is
higher than set in 4-51 Warning Current [25] Comparator 3 Comparator 3 [25] Use the result of
High. comparator 3.

[10] Out of speed Out of speed range [10] The speed is [26] Logic rule 0 Logic rule 0 [26] Use the result of logic
range outside the range set in 4-52 Warning rule 0.
Speed Low and 4-53 Warning Speed [27] Logic rule 1 Logic rule 1 [27] Use the result of logic
High. rule 1.
[11] Below speed low Below speed low [11] The output speed [28] Logic rule 2 Logic rule 2 [28] Use the result of logic
is lower than the setting in rule 2.
4-52 Warning Speed Low.
[29] Logic rule 3 Logic rule 3 [29] Use the result of logic
[12] Above speed Above speed high [12] The output rule 3.
high speed is higher than the setting in
[33] Digital input DI18 Digital input DI18 [33] Use the result of
4-53 Warning Speed High.
digital input 18.
[13] Out of feedb. Out of feedb. Range [13] The feedback
[34] Digital input DI19 Digital input DI19 [34] Use the result of
range is outside the range set in
digital input 19.
4-56 Warning Feedback Low and
4-57 Warning Feedback High. [35] Digital input DI27 Digital input DI27 [35] Use the result of
digital input 27.
[14] Below feedb. low Below feedb. Low [14] The feedback is
below the limit set in 4-56 Warning [36] Digital input DI29 Digital input DI27 [35] Use the result of
Feedback Low. digital input 29.

[15] Above feedb. Above feedb. High [15] The feedback is [37] Digital input DI32 Digital input DI32 [37] Use the result of
high above the limit set in 4-57 Warning digital input 32.
Feedback High.
[38] Digital input DI33 Digital input DI33 [38] Use the result of
[16] Thermal warning Thermal warning [16] The thermal digital input 33.
warning turns on when the
[39] Start command Start command [39] A start command is
temperature exceeds the limit in the
issued.
motor, the Adjustable frequency drive,
the brake resistor or the thermistor. [40] Drive stopped Drive stopped [40] A stop command
(Jog, Stop, Qstop, Coast) is issued –
[17] Mains out of Mains out of range [17] The AC line
and not from the SLC itself.
range voltage is outside the specified voltage
range. [41] Reset Trip Reset Trip [41] A reset is issued

MG33MD22 - VLT® is a registered Danfoss trademark 3-111

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

13-01 Start Event 13-02 Stop Event

Option: Function: Select the Boolean (TRUE or FALSE) input to activate Smart Logic
[42] Auto-reset Trip Auto-reset Trip [42]: an auto reset is Control.

3 3 [43] Ok key
performed.

OK key [43] The [OK] key is pressed.

Option:
[14] Below feedb. low
Function:

[15] Above feedb. high

[44] Reset key Reset key [44] The [Reset] key is
[16] Thermal warning
pressed.
[17] Mains out of range
[45] Left key Left key [45] The [◄] key is pressed. [18] Reversing
[46] Right key Right key [46] The[►] key is pressed. [19] Warning
[20] Alarm (trip)
[47] Up key Up key [47] The [▲] key is pressed.
[21] Alarm (trip lock)
[48] Down key Down key [48] The [▼] key is pressed. [22] Comparator 0
[23] Comparator 1
[50] Comparator 4 Comparator 4 [50] Use the result of
comparator 4. [24] Comparator 2
[25] Comparator 3
[51] Comparator 5 Comparator 5 [51] Use the result of
[26] Logic rule 0
comparator 5.
[27] Logic rule 1
[60] Logic rule 4 Logic rule 4 [60] Use the result of logic [28] Logic rule 2
rule 4. [29] Logic rule 3
[61] Logic rule 5 Logic rule 5 [61] Use the result of logic [30] SL Time-out 0
rule 5. [31] SL Time-out 1
[32] SL Time-out 2
[94] RS Flipflop 0
[33] Digital input DI18
[95] RS Flipflop 1
[34] Digital input DI19
[96] RS Flipflop 2
[35] Digital input DI27
[97] RS Flipflop 3
[36] Digital input DI29
[98] RS Flipflop 4
[37] Digital input DI32
[99] RS Flipflop 5
[38] Digital input DI33
[100] RS Flipflop 6
[39] Start command
[101] RS Flipflop 7
[40] Drive stopped
13-02 Stop Event [41] Reset Trip
Select the Boolean (TRUE or FALSE) input to activate Smart Logic [42] Auto-reset Trip
Control. [43] Ok key
Option: Function: [44] Reset key
[45] Left key
[0] * False For descriptions [0] - [61], see
13-01 Start Event Start Event [46] Right key
[47] Up key
[1] True
[48] Down key
[2] Running
[50] Comparator 4
[3] In range
[51] Comparator 5
[4] On reference
[60] Logic rule 4
[5] Torque limit
[61] Logic rule 5
[6] Current limit
[70] SL Time-out 3 SL Timeout 3 [70] Smart Logic
[7] Out of current range
Controller timer 3 is timed out.
[8] Below I low
[71] SL Time-out 4 SL Timeout 4 [71] Smart Logic
[9] Above I high
Controller timer 4 is timed out.
[10] Out of speed range
[11] Below speed low [72] SL Time-out 5 SL Timeout 5 [72] Smart Logic
[12] Above speed high Controller timer 5 is timed out.
[13] Out of feedb. range

3-112 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

13-02 Stop Event 13-03 Reset SLC

Select the Boolean (TRUE or FALSE) input to activate Smart Logic Option: Function:
Control. [0] * Do not reset Retains programmed settings in all group
Option:
[73] SL Time-out 6
Function:
SL- Timeout 6 [73] Smart Logic [1]
SLC

Reset SLC
13 parameters (13-**).

Resets all group 13 parameters (13-**) to

3 3
Controller timer 6 is timed out. default settings.
[74] SL Time-out 7 SL Timeout 7 [74] Smart Logic
Controller timer 7 is timed out.
3.14.3 13-1* Comparators
[75] Start command given
[76] Digital input x30/2 Comparators are used for comparing continuous variables
[77] Digital input x30/3 (i.e., output frequency, output current, analog input, etc.)
[78] Digital input x30/4 to fixed preset values.
[79] Digital input x46/1
[80] Digital input x46/3 Par. LC-11

130BB672.10
Comparator Operator
[81] Digital input x46/5 Par. LC-10
[82] Digital input x46/7 Comparator Operand

[83] Digital input x46/9 =

Par. LC-12 TRUE longer than.
[84] Digital input x46/11
Comparator Value ...
[85] Digital input x46/13 ...
[90] ATEX ETR cur. warning Selectable if 1-90 Motor Thermal
Protection is set to [20] or [21]. If
the alarm 164 ATEX ETR
In addition, there are digital values that will be compared
cur.lim.alarm is active, the output
to fixed time values. See explanation in 13-10 Comparator
will be 1.
Operand. Comparators are evaluated once in each scan
[91] ATEX ETR cur. alarm Selectable if 1-90 Motor Thermal interval. Use the result (TRUE or FALSE) directly. All
Protection is set to [20] or [21]. If parameters in this parameter group are array parameters
the alarm 166 ATEX ETR with index 0 to 5. Select index 0 to program Comparator 0,
freq.lim.alarm is active, the output select index 1 to program Comparator 1, etc.
will be 1.
13-10 Comparator Operand
[92] ATEX ETR freq. warning Selectable if 1-90 Motor Thermal Array [6]
Protection is set to [20] or [21]. If
Option: Function:
the alarm 163 ATEX ETR
cur.lim.warning is active, the Choices [1] to [31] are variables that will
output will be 1. be compared based on their values.
Choices [50] to [186] are digital values
[93] ATEX ETR freq. alarm Selectable if 1-90 Motor Thermal (TRUE/FALSE) where the comparison is
Protection is set to [20] or [21]. If based on the amount of time during
the warning 165 ATEX ETR which they are set to TRUE or FALSE,
freq.lim.warning is active, the respectively. See 13-11 Comparator
output will be 1. Operator.
[94] RS Flipflop 0 Select the variable to be monitored by
[95] RS Flipflop 1 the comparator.
[96] RS Flipflop 2 [0] * DISABLED DISABLED [0] The comparator is
[97] RS Flipflop 3 disabled.
[98] RS Flipflop 4
[1] Reference Reference [1] The resulting remote
[99] RS Flipflop 5
reference (not local) as a percentage.
[100] RS Flipflop 6
[101] RS Flipflop 7 [2] Feedback Feedback [2] In the unit [RPM] or [Hz]

[3] Motor speed Motor speed [3] [RPM] or [Hz]

[4] Motor current Motor current [4] [A]

[5] Motor torque Motor torque [5] [Nm]

MG33MD22 - VLT® is a registered Danfoss trademark 3-113

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

13-10 Comparator Operand 13-10 Comparator Operand

Array [6] Array [6]
Option: Function: Option: Function:

3 3 [6] Motor power Motor power [6] [kW] or [hp] [54] Running Running [54] The motor is running.

[7] Motor voltage Motor voltage [7] [V] [55] Reversing Reversing [55] The output is high when
the Adjustable frequency drive is
[8] DC-link voltage DC-link voltage [8] [V]
running counter clockwise (the logical
[9] Motor thermal Motor thermal [9] Expressed as a product of the status bits “running”
percentage. AND “reverse”)
[10] Drive thermal VLT thermal [10] Expressed as a [56] In range In range [56] The motor is running
percentage. within the programmed current and
[11] Heat sink temp. Heatsink temp [11] Expressed as a speed ranges set in 4-50 Warning
percentage. Current Low to 4-53 Warning Speed High.

[12] Analog input Analog input AI53 [12] Expressed as a [60] On reference On reference [60] The motor is running
AI53 percentage. on reference.

[13] Analog input Analog input AI54 [13] Expressed as a [61] Below reference, Below reference, low [61] The motor is
AI54 percentage. low running below the value given in
4-54 Warning Reference Low
[14] Analog input Analog input AIFB10 [14] [V]. AIFB10 is
AIFB10 internal 10V supply. [62] Above ref, high Above reference, high [62] The motor is
running above the value given in
[15] Analog input Analog input AIS24V [15] [V] Analog
4-55 Warning Reference High
AIS24V input AICCT [17] [°]. AIS24V is switch
mode power supply: SMPS 24V. [65] Torque limit Torque limit [65] The torque limit, set in
4-16 Torque Limit Motor Mode or
[17] Analog input Analog input AICCT [17] [°]. AICCT is
4-17 Torque Limit Generator Mode, has
AICCT control card temperature.
been exceeded.
[18] Pulse input FI29 Pulse input FI29 [18] Expressed as a
[66] Current limit Current limit [66] The motor current
percentage.
limit, set in 4-18 Current Limit, has been
[19] Pulse input FI33 Pulse input FI33 [19] Expressed as a exceeded.
percentage.
[67] Out of current Out of current range [67] The motor
[20] Alarm number Alarm number [20] The error number. range current is outside the range set in
4-18 Current Limit.
[21] Warning number
[22] Analog input [68] Below I low Below I low [68] The motor current is
x30 11 lower than set in 4-50 Warning Current
[23] Analog input Low.
x30 12 [69] Above I high Above I high [69] The motor current is
[30] Counter A Counter A [30] Number of counts higher than set in 4-51 Warning Current
[31] Counter B Counter B [31] Number of counts High.

[50] FALSE False [50] Enters the fixed value of false [70] Out of speed Out of speed range [70] The speed is
in the comparator. range outside the range set in 4-52 Warning
Speed Low and 4-53 Warning Speed High.
[51] TRUE True [51] Enters the fixed value of true
in the comparator. [71] Below speed low Below speed low [71] The output speed
is lower than the setting in
[52] Control ready Control ready [52] The control board
4-52 Warning Speed Low.
receives supply voltage
[72] Above speed Above speed high [72] The output speed
[53] Drive ready Drive ready [53] The Adjustable
high is higher than the setting in
frequency drive is ready for operation
4-53 Warning Speed High.
and applies a supply signal on the
control board. [75] Out of feedb. Out of feedb. Range [75] The feedback is
range outside the range set in 4-56 Warning

3-114 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

13-10 Comparator Operand 13-10 Comparator Operand

Array [6] Array [6]
Option: Function: Option: Function:
Feedback Low and 4-57 Warning
Feedback High.
[110] Logic rule 0 Logic rule 0 [110] The result of logic rule
0.
3 3
[76] Below feedb. Below feedb. Low [76] The feedback is [111] Logic rule 1 Logic rule 1 [111] The result of logic rule
low below the limit set in 4-56 Warning 1.
Feedback Low.
[112] Logic rule 2 Logic rule 2 [112] The result of logic rule
[77] Above feedb. Above feedb. High [77] The feedback is 2.
high above the limit set in 4-57 Warning
[113] Logic rule 3 Logic rule 3 [113] The result of logic rule
Feedback High.
3.
[80] Thermal warning Thermal warning [80] The thermal
[114] Logic rule 4 Logic rule 4 [114] The result of logic rule
warning turns on when the temperature
4.
exceeds the limit in the motor, the
Adjustable frequency drive, the brake [115] Logic rule 5 Logic rule 5 [115] The result of logic rule
resistor or thermistor. 5.

[82] Mains out of Line power out of range [82] The AC line [120] SL Time-out 0 SL Timeout 0 [120] The result of SLC
range voltage is outside the specified voltage timer 0.
range. [121] SL Time-out 1 SL Timeout 1 [121] The result of SLC
[85] Warning Warning [85] A warning is active. timer 1.

[86] Alarm (trip) Alarm (trip) [86] A (trip) alarm is active. [122] SL Time-out 2 SL Timeout 2 [122] The result of SLC
timer 2.
[87] Alarm (trip lock) Alarm (trip lock) [87] A (Trip lock) alarm
is active. [123] SL Time-out 3 SL Timeout 3 [123] The result of SLC
timer 3.
[90] Bus OK Bus OK [90] Active communication (no
timeout) via the serial communication [124] SL Time-out 4 SL Timeout 4 [124] The result of SLC
port. timer 4.

[91] Torque limit & Torque limit & stop [91] If the Adjustable [125] SL Time-out 5 SL Timeout 5 [125] The result of SLC
stop frequency drive has received a stop timer 5.
signal and is at the torque limit, the [126] SL Time-out 6 SL Timeout 6 [126] The result of SLC
signal is logic “0”. timer 6.
[92] Brake fault Brake fault (IGBT) [92] The brake IGBT is [127] SL Time-out 7 SL Timeout 7 [127] The result of SLC
(IGBT) short circuited. timer 7.
[93] Mech. brake Mech. brake control [93] The mechanical [130] Digital input Digital input DI18 [130] Digital input 18.
control brake is active. DI18 High = True.
[94] Safe stop active [131] Digital input Digital input DI19 [131] Digital input 19.
[100] Comparator 0 Comparator 0 [100] The result of DI19 High = True.
comparator 0.
[132] Digital input Digital input DI27 [132] Digital input 27.
[101] Comparator 1 Comparator 1 [101] The result of DI27 High = True.
comparator 1.
[133] Digital input Digital input DI29 [133] Digital input 29.
[102] Comparator 2 Comparator 2 [102] The result of DI29 High = True.
comparator 2.
[134] Digital input Digital input DI32 [134] Digital input 32.
[103] Comparator 3 Comparator 3 [103] The result of DI32 High = True.
comparator 3.
[135] Digital input Digital input DI33 [135] Digital input 33.
[104] Comparator 4 Comparator 4 [104] The result of DI33 High = True.
comparator 4.
[150] SL digital output SL digital output A [150] Use the result
[105] Comparator 5 Comparator 5 [105] The result of A of the SLC output A.
comparator 5.

MG33MD22 - VLT® is a registered Danfoss trademark 3-115

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

13-10 Comparator Operand 13-10 Comparator Operand

Array [6] Array [6]
Option: Function: Option: Function:

3 3 [151] SL digital output SL digital output B [151] Use the result of

B the SLC output B.
[195] Digital input x46
3
[196] Digital input x46
[152] SL digital output SL digital output C [152] Use the result
4
C of the SLC output C.
[197] Digital input x46
[153] SL digital output SL digital output D [153] Use the result 5
D of the SLC output D.
[198] Digital input x46
[154] SL digital output SL digital output E [154] Use the result of 6
E the SLC output E. [199] Digital input x46
7
[155] SL digital output SL digital output F [155] Use the result of
F the SLC output F. 13-11 Comparator Operator
[160] Relay 1 Relay 1 [160] Relay 1 is active Array [6]
[161] Relay 2 Relay 2 [161] Relay 2 is active Option: Function:
[180] Local ref. active Local ref. active [180] High when Select the operator to be used in the
3-13 Reference Site = [2] Local or when comparison. This is an array parameter
3-13 Reference Site is [0] Linked to hand containing comparator operators 0 to 5.
auto, at the same time as the LCP is in [0] < Select < [0] for the result of the evaluation to
hand on mode. be TRUE, when the variable selected in
[181] Remote ref. Remote ref. active [181] High when 13-10 Comparator Operand is smaller than the
active 3-13 Reference Site= [1] Remote or [0] fixed value in 13-12 Comparator Value. The
Linked to hand/auto, while the LCP is in result will be FALSE, if the variable selected in
auto on mode. 13-10 Comparator Operand is greater than the
fixed value in 13-12 Comparator Value.
[182] Start command Start command [182] High when there is
an active start command and no stop [1] * ≈ (equal) Select ≈ [1] for the result of the evaluation to
command. be TRUE, when the variable selected in
13-10 Comparator Operand is approximately
[183] Drive stopped Drive stopped [183] A stop command
equal to the fixed value in 13-12 Comparator
(Jog, Stop, Qstop, Coast) is issued – and
Value.
not from the SLC itself.
[2] > Select > [2] for the inverse logic of option <
[185] Drive in hand Drive in hand mode [185] High when the
[0].
mode Adjustable frequency drive is in hand
mode. [5] TRUE longer
than..
[186] Drive in auto Drive in auto mode [186] High when the
[6] FALSE
mode Adjustable frequency drive is in auto
longer
mode.
than..
[187] Start command [7] TRUE
given shorter
[190] Digital input x30 than..
2 [8] FALSE
[191] Digital input x30 shorter
3 than..
[192] Digital input x30
4
[193] Digital input x46
1
[194] Digital input x46
2

3-116 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

13-12 Comparator Value Parameter Setting Notes

Array [6]
[37] Digital
Range: Function: 13-40 Logic Rule Boolean 1 [1]
Input DI32
Size related* [-100000.000 -
100000.000 ]
Enter the ‘trigger level’ for the
variable that is monitored by
13-42 Logic Rule Boolean 2 [1] [2] Running 3 3
13-41 Logic Rule Operator 1 [1] [1] AND
this comparator. This is an
array parameter containing
[26] Logic Output from 13-41
comparator values 0 to 5. 13-15 RS-FF Operand S [0]
rule 0 [0]
Application [-100000.000 - Enter the ‘trigger level’ for the [27] Logic Output from 13-41
dependent* 100000.000 ] variable that is monitored by 13-16 RS-FF Operand R [0]
rule 1 [1]
this comparator. This is an
array parameter containing
Output from
comparator values 0 to 5. [94] RS
13-51 SL Controller Event [0] evaluating 13-15
Flipflop 0
and 13-16
3.14.4 13-1* RS Flip Flops 13-52 SL Controller Action [0] [22] Run

The Reset-Set Flip Flops hold the signal until set/reset. [27] Logic
13-51 SL Controller Event [1]
rule 1
13-52 SL Controller Action [1] [24] Stop
130BB959.10

Par. 13-15
RS-FF Operand S
13-15 RS-FF Operand S
Par. 13-16
RS-FF Operand R Option: Function:
[0] False
[1] True
[2] Running
Two parameters are used and the output can be used in
[3] In range
the logic rules and as events.
[4] On reference
[5] Torque limit
130BB960.10

S [6] Current limit

[7] Out of current range
R
[8] Below I low
Flip Flop Output [9] Above I high
[10] Out of speed range
[11] Below speed low
The two operators can be selected from a long list. As a
[12] Above speed high
special case, the same digital input can be used as both
[13] Out of feedb. range
Set and Reset, making it possible to use the same digital
input as start/stop. The following settings can be used to [14] Below feedb. low
set up the same digital input as start/stop (example given [15] Above feedb. high
with DI32 but is not a requirement). [16] Thermal warning
[17] Mains out of range

Parameter Setting Notes [18] Reversing

13-00 SL Controller Mode On [19] Warning
13-01 Start Event TRUE [20] Alarm (trip)
13-02 Stop Event FALSE [21] Alarm (trip lock)
[22] Comparator 0
[37] Digital [23] Comparator 1
13-40 Logic Rule Boolean 1 [0] [24] Comparator 2
Input DI32
13-42 Logic Rule Boolean 2 [0] [2] Running [25] Comparator 3
[3] AND [26] Logic rule 0
13-41 Logic Rule Operator 1 [0]
NOT [27] Logic rule 1
[28] Logic rule 2

MG33MD22 - VLT® is a registered Danfoss trademark 3-117

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

13-15 RS-FF Operand S 13-15 RS-FF Operand S

Option: Function: Option: Function:
[29] Logic rule 3 [99] RS Flipflop 5

3 3 [30]
[31]
SL Time-out 0
SL Time-out 1
[100]
[101]
RS Flipflop 6
RS Flipflop 7
[32] SL Time-out 2
13-16 RS-FF Operand R
[33] Digital input DI18
[34] Digital input DI19 Option: Function:
[35] Digital input DI27 [0] False
[36] Digital input DI29 [1] True
[37] Digital input DI32 [2] Running
[38] Digital input DI33 [3] In range
[39] Start command [4] On reference
[40] Drive stopped [5] Torque limit
[41] Reset Trip [6] Current limit
[42] Auto-reset Trip [7] Out of current range
[43] Ok key [8] Below I low
[44] Reset key [9] Above I high
[45] Left key [10] Out of speed range
[46] Right key [11] Below speed low
[47] Up key [12] Above speed high
[48] Down key [13] Out of feedb. range
[50] Comparator 4 [14] Below feedb. low
[51] Comparator 5 [15] Above feedb. high
[60] Logic rule 4 [16] Thermal warning
[61] Logic rule 5 [17] Mains out of range
[70] SL Time-out 3 [18] Reversing
[71] SL Time-out 4 [19] Warning
[72] SL Time-out 5 [20] Alarm (trip)
[73] SL Time-out 6 [21] Alarm (trip lock)
[74] SL Time-out 7 [22] Comparator 0
[75] Start command given [23] Comparator 1
[76] Digital input x30/2 [24] Comparator 2
[77] Digital input x30/3 [25] Comparator 3
[78] Digital input x30/4 [26] Logic rule 0
[79] Digital input x46/1 [27] Logic rule 1
[80] Digital input x46/3 [28] Logic rule 2
[81] Digital input x46/5 [29] Logic rule 3
[82] Digital input x46/7 [30] SL Time-out 0
[83] Digital input x46/9 [31] SL Time-out 1
[84] Digital input x46/11 [32] SL Time-out 2
[85] Digital input x46/13 [33] Digital input DI18
[90] ATEX ETR cur. warning [34] Digital input DI19
[91] ATEX ETR cur. alarm [35] Digital input DI27
[92] ATEX ETR freq. warning [36] Digital input DI29
[93] ATEX ETR freq. alarm [37] Digital input DI32
[94] RS Flipflop 0 [38] Digital input DI33
[95] RS Flipflop 1 [39] Start command
[96] RS Flipflop 2 [40] Drive stopped
[97] RS Flipflop 3 [41] Reset Trip
[98] RS Flipflop 4 [42] Auto-reset Trip

3-118 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

13-16 RS-FF Operand R All parameters in this parameter group are array
Option: Function: parameters with index 0 to 2. Select index 0 to program
Timer 0, select index 1 to program Timer 1, and so on.
[43] Ok key
[44]
[45]
Reset key
Left key
13-20 SL Controller Timer
Range: Function:
3 3
[46] Right key Application [Application Enter the value to define the
[47] Up key dependent* dependant] duration of the FALSE output
[48] Down key from the programmed timer. A
[50] Comparator 4 timer is only FALSE if it is started
[51] Comparator 5 by an action (i.e., Start timer 1
[60] Logic rule 4 [29]) and until the given timer
[61] Logic rule 5 value has elapsed.
[70] SL Time-out 3
[71] SL Time-out 4
3.14.6 13-4* Logic Rules
[72] SL Time-out 5
[73] SL Time-out 6
Combine up to three boolean inputs (TRUE / FALSE inputs)
[74] SL Time-out 7 from timers, comparators, digital inputs, status bits and
[75] Start command given events using the logical operators AND, OR, and NOT.
[76] Digital input x30/2 Select Boolean inputs for the calculation in 13-40 Logic Rule
[77] Digital input x30/3 Boolean 1, 13-42 Logic Rule Boolean 2 and 13-44 Logic Rule
[78] Digital input x30/4 Boolean 3. Define the operators used to logically combine
[79] Digital input x46/1 the selected inputs in 13-41 Logic Rule Operator 1 and
[80] Digital input x46/3 13-43 Logic Rule Operator 2.
[81] Digital input x46/5
[82] Digital input x46/7 Par. LC-41 Par. LC-43

130BB673.10
Logic Rule Operator 1 Logic Rule Operator 2
[83] Digital input x46/9 Par. LC-40
Logic Rule Boolean 1
[84] Digital input x46/11
Par. LC-42
[85] Digital input x46/13 Logic Rule Boolean 2 ...
...
[90] ATEX ETR cur. warning ...
...
[91] ATEX ETR cur. alarm
[92] ATEX ETR freq. warning Par. LC-44
Logic Rule Boolean 3
[93] ATEX ETR freq. alarm
[94] RS Flipflop 0
[95] RS Flipflop 1 Priority of calculation
[96] RS Flipflop 2
The results of 13-40 Logic Rule Boolean 1, 13-41 Logic Rule
Operator 1 and 13-42 Logic Rule Boolean 2 are calculated
[97] RS Flipflop 3
first. The outcome (TRUE / FALSE) of this calculation is
[98] RS Flipflop 4
combined with the settings of 13-43 Logic Rule Operator 2
[99] RS Flipflop 5
and 13-44 Logic Rule Boolean 3, yielding the final result
[100] RS Flipflop 6
(TRUE / FALSE) of the logic rule.
[101] RS Flipflop 7
13-40 Logic Rule Boolean 1
3.14.5 13-2* Timers Array [6]
Option: Function:
Use the result (TRUE or FALSE) from timers directly to [0] * False Select the first Boolean (TRUE or
define an event (see 13-51 SL Controller Event), or as FALSE) input for the selected logic
Boolean input in a logic rule (see 13-40 Logic Rule Boolean rule.
1, 13-42 Logic Rule Boolean 2 or 13-44 Logic Rule Boolean 3). See 13-01 Start Event ([0] - [61])
A timer is only FALSE when started by an action (i.e., Start and 13-02 Stop Event ([70] - [75])
timer 1 [29]) until the timer value entered in this for further description.
parameter is elapsed. Then it becomes TRUE again.
[1] True
[2] Running

MG33MD22 - VLT® is a registered Danfoss trademark 3-119

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

13-40 Logic Rule Boolean 1 13-40 Logic Rule Boolean 1

Array [6] Array [6]
Option: Function: Option: Function:

3 3 [3]
[4]
In range
On reference
[60]
[61]
Logic rule 4
Logic rule 5
[5] Torque limit [70] SL Time-out 3
[6] Current limit [71] SL Time-out 4
[7] Out of current range [72] SL Time-out 5
[8] Below I low [73] SL Time-out 6
[9] Above I high [74] SL Time-out 7
[10] Out of speed range [75] Start command given
[11] Below speed low [76] Digital input x30/2
[12] Above speed high [77] Digital input x30/3
[13] Out of feedb. range [78] Digital input x30/4
[14] Below feedb. low [79] Digital input x46/1
[15] Above feedb. high [80] Digital input x46/3
[16] Thermal warning [81] Digital input x46/5
[17] Mains out of range [82] Digital input x46/7
[18] Reversing [83] Digital input x46/9
[19] Warning [84] Digital input x46/11
[20] Alarm (trip) [85] Digital input x46/13
[21] Alarm (trip lock) [90] ATEX ETR cur. warning Selectable if 1-90 Motor Thermal
[22] Comparator 0 Protection is set to [20] or [21]. If
[23] Comparator 1 the alarm 164 ATEX ETR
[24] Comparator 2 cur.lim.alarm is active, the output
[25] Comparator 3 will be 1.
[26] Logic rule 0 [91] ATEX ETR cur. alarm Selectable if1-90 Motor Thermal
[27] Logic rule 1 Protection is set to [20] or [21]. If
[28] Logic rule 2 the alarm 166 ATEX ETR
[29] Logic rule 3 freq.lim.alarm is active, the output
[30] SL Time-out 0 will be 1.
[31] SL Time-out 1 [92] ATEX ETR freq. warning Selectable if 1-90 Motor Thermal
[32] SL Time-out 2 Protection is set to [20] or [21]. If
[33] Digital input DI18 the alarm 163 ATEX ETR
[34] Digital input DI19 cur.lim.warning is active, the
[35] Digital input DI27 output will be 1.
[36] Digital input DI29 [93] ATEX ETR freq. alarm Selectable if 1-90 Motor Thermal
[37] Digital input DI32 Protection is set to [20] or [21]. If
[38] Digital input DI33 the warning 165 ATEX ETR
[39] Start command freq.lim.warning is active, the
[40] Drive stopped output will be 1.
[41] Reset Trip
[94] RS Flipflop 0
[42] Auto-reset Trip
[95] RS Flipflop 1
[43] Ok key
[96] RS Flipflop 2
[44] Reset key
[97] RS Flipflop 3
[45] Left key
[98] RS Flipflop 4
[46] Right key
[99] RS Flipflop 5
[47] Up key
[100] RS Flipflop 6
[48] Down key
[101] RS Flipflop 7
[50] Comparator 4
[51] Comparator 5

3-120 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

13-41 Logic Rule Operator 1 13-42 Logic Rule Boolean 2

Array [6] Array [6]
Option: Function: Option: Function:
Select the first logical operator to use on
the Boolean inputs from 13-40 Logic Rule
[15]
[16]
Above feedb. high
Thermal warning
3 3
Boolean 1 and 13-42 Logic Rule Boolean 2. [17] Mains out of range
[13-**] signifies the Boolean input of [18] Reversing
parameter group 13-**. [19] Warning
[0] * DISABLED Ignores 13-42 Logic Rule Boolean 2, [20] Alarm (trip)
13-43 Logic Rule Operator 2, and 13-44 Logic [21] Alarm (trip lock)
Rule Boolean 3. [22] Comparator 0

[1] AND Evaluates the expression [13-40] AND [23] Comparator 1

[13-42]. [24] Comparator 2
[25] Comparator 3
[2] OR evaluates the expression [13-40] OR [13-42].
[26] Logic rule 0
[3] AND NOT evaluates the expression [13-40] AND NOT [27] Logic rule 1
[13-42]. [28] Logic rule 2
[4] OR NOT evaluates the expression [13-40] OR NOT [29] Logic rule 3
[13-42]. [30] SL Time-out 0
[31] SL Time-out 1
[5] NOT AND evaluates the expression NOT [13-40] AND
[32] SL Time-out 2
[13-42].
[33] Digital input DI18
[6] NOT OR evaluates the expression NOT [13-40] OR
[34] Digital input DI19
[13-42].
[35] Digital input DI27
[7] NOT AND NOT evaluates the expression NOT [13-40] AND [36] Digital input DI29
NOT [13-42]. [37] Digital input DI32
[8] NOT OR NOT evaluates the expression NOT [13-40] OR [38] Digital input DI33
NOT [13-42]. [39] Start command
[40] Drive stopped
13-42 Logic Rule Boolean 2 [41] Reset Trip
Array [6] [42] Auto-reset Trip
[43] Ok key
Option: Function:
[44] Reset key
[0] * False Select the second Boolean (TRUE
[45] Left key
or FALSE) input for the selected
logic rule. See 13-01 Start Event [46] Right key
([0] - [61]) and 13-02 Stop Event [47] Up key
([70] - [75]) for further description. [48] Down key
[50] Comparator 4
[1] True
[51] Comparator 5
[2] Running
[60] Logic rule 4
[3] In range
[61] Logic rule 5
[4] On reference
[70] SL Time-out 3
[5] Torque limit
[71] SL Time-out 4
[6] Current limit
[72] SL Time-out 5
[7] Out of current range
[73] SL Time-out 6
[8] Below I low
[74] SL Time-out 7
[9] Above I high
[75] Start command given
[10] Out of speed range
[76] Digital input x30/2
[11] Below speed low
[77] Digital input x30/3
[12] Above speed high
[78] Digital input x30/4
[13] Out of feedb. range
[79] Digital input x46/1
[14] Below feedb. low

MG33MD22 - VLT® is a registered Danfoss trademark 3-121

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

13-42 Logic Rule Boolean 2 13-43 Logic Rule Operator 2

Array [6] Array [6]
Option: Function: Option: Function:

3 3 [80]
[81]
Digital input x46/3
Digital input x46/5
13-41 Logic Rule Operator 1, and 13-42 Logic
Rule Boolean 2. DISABLED [0] (factory
[82] Digital input x46/7 setting). select this option to ignore
[83] Digital input x46/9 13-44 Logic Rule Boolean 3.
[84] Digital input x46/11 [0] * DISABLED
[85] Digital input x46/13 [1] AND
[90] ATEX ETR cur. warning Selectable if 1-90 Motor Thermal [2] OR
Protection is set to [20] or [21]. If [3] AND NOT
the alarm 164 ATEX ETR [4] OR NOT
cur.lim.alarm is active, the output [5] NOT AND
will be 1.
[6] NOT OR
[91] ATEX ETR cur. alarm Selectable if 1-90 Motor Thermal [7] NOT AND NOT
Protection is set to [20] or [21]. If [8] NOT OR NOT
the alarm 166 ATEX ETR
freq.lim.alarm is active, the output 13-44 Logic Rule Boolean 3
will be 1. Array [6]

[92] ATEX ETR freq. warning Selectable if1-90 Motor Thermal Option: Function:
Protection is set to [20] or [21]. If [0] * False Select the third Boolean (TRUE or
the alarm 163 ATEX ETR FALSE) input for the selected logic
cur.lim.warning is active, the rule. See 13-01 Start Event ([0] -
output will be 1. [61]) and 13-02 Stop Event ([70] -
[75]) for further description.
[93] ATEX ETR freq. alarm Selectable if 1-90 Motor Thermal
Protection is set to [20] or [21]. If [1] True
the warning 165 ATEX ETR [2] Running
freq.lim.warning is active, the [3] In range
output will be 1. [4] On reference
[94] RS Flipflop 0 [5] Torque limit
[95] RS Flipflop 1 [6] Current limit
[96] RS Flipflop 2 [7] Out of current range
[97] RS Flipflop 3 [8] Below I low
[98] RS Flipflop 4 [9] Above I high
[99] RS Flipflop 5 [10] Out of speed range
[100] RS Flipflop 6 [11] Below speed low
[101] RS Flipflop 7 [12] Above speed high
[13] Out of feedb. range
13-43 Logic Rule Operator 2 [14] Below feedb. low
Array [6] [15] Above feedb. high
Option: Function: [16] Thermal warning
Select the second logical operator to be [17] Mains out of range
used on the Boolean input calculated in [18] Reversing
13-40 Logic Rule Boolean 1, 13-41 Logic Rule [19] Warning
Operator 1, and 13-42 Logic Rule Boolean 2, [20] Alarm (trip)
and the Boolean input coming from [21] Alarm (trip lock)
13-42 Logic Rule Boolean 2. [22] Comparator 0
[13-44] signifies the Boolean input of [23] Comparator 1
13-44 Logic Rule Boolean 3. [24] Comparator 2
[13-40/13-42] signifies the Boolean input [25] Comparator 3
calculated in 13-40 Logic Rule Boolean 1,
[26] Logic rule 0

3-122 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

13-44 Logic Rule Boolean 3 13-44 Logic Rule Boolean 3

Array [6] Array [6]
Option: Function: Option: Function:
[27]
[28]
Logic rule 1
Logic rule 2
[91] ATEX ETR cur. alarm Selectable if 1-90 Motor Thermal
Protection is set to [20] or [21]. If
3 3
[29] Logic rule 3 the alarm 166 ATEX ETR
[30] SL Time-out 0 freq.lim.alarm is active, the output
[31] SL Time-out 1 will be 1.
[32] SL Time-out 2 [92] ATEX ETR freq. warning Selectable if 1-90 Motor Thermal
[33] Digital input DI18 Protection is set to [20] or [21]. If
[34] Digital input DI19 the alarm 163 ATEX ETR
[35] Digital input DI27 cur.lim.warning is active, the
[36] Digital input DI29 output will be 1.
[37] Digital input DI32 [93] ATEX ETR freq. alarm Selectable if 1-90 Motor Thermal
[38] Digital input DI33 Protection is set to [20] or [21]. If
[39] Start command the warning 165 ATEX ETR
[40] Drive stopped freq.lim.warning is active, the
[41] Reset Trip output will be 1.
[42] Auto-reset Trip [94] RS Flipflop 0
[43] Ok key [95] RS Flipflop 1
[44] Reset key [96] RS Flipflop 2
[45] Left key [97] RS Flipflop 3
[46] Right key [98] RS Flipflop 4
[47] Up key [99] RS Flipflop 5
[48] Down key [100] RS Flipflop 6
[50] Comparator 4 [101] RS Flipflop 7
[51] Comparator 5
[60] Logic rule 4
3.14.7 13-5* States
[61] Logic rule 5
[70] SL Time-out 3
13-51 SL Controller Event
[71] SL Time-out 4
[72] SL Time-out 5 Array [20]

[73] SL Time-out 6 Option: Function:

[74] SL Time-out 7 [0] * False Select the Boolean input (TRUE or
[75] Start command given FALSE) to define the Smart Logic
[76] Digital input x30/2 Controller event. See 13-01 Start
[77] Digital input x30/3 Event ([0] - [61]) and 13-02 Stop
[78] Digital input x30/4 Event ([70] - [74]) for further
[79] Digital input x46/1 description.

[80] Digital input x46/3 [1] True

[81] Digital input x46/5 [2] Running
[82] Digital input x46/7 [3] In range
[83] Digital input x46/9 [4] On reference
[84] Digital input x46/11 [5] Torque limit
[85] Digital input x46/13 [6] Current limit
[90] ATEX ETR cur. warning Selectable if 1-90 Motor Thermal [7] Out of current range
Protection is set to [20] or [21]. If [8] Below I low
the alarm 164 ATEX ETR [9] Above I high
cur.lim.alarm is active, the output [10] Out of speed range
will be 1. [11] Below speed low
[12] Above speed high

MG33MD22 - VLT® is a registered Danfoss trademark 3-123

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

13-51 SL Controller Event 13-51 SL Controller Event

Array [20] Array [20]
Option: Function: Option: Function:

3 3 [13]
[14]
Out of feedb. range
Below feedb. low
[78]
[79]
Digital input x30/4
Digital input x46/1
[15] Above feedb. high [80] Digital input x46/3
[16] Thermal warning [81] Digital input x46/5
[17] Mains out of range [82] Digital input x46/7
[18] Reversing [83] Digital input x46/9
[19] Warning [84] Digital input x46/11
[20] Alarm (trip) [85] Digital input x46/13
[21] Alarm (trip lock) [90] ATEX ETR cur. warning Selectable if 1-90 Motor Thermal
[22] Comparator 0 Protection is set to [20] or [21]. If
[23] Comparator 1 the alarm 164 ATEX ETR
[24] Comparator 2 cur.lim.alarm is active, the output
[25] Comparator 3 will be 1.
[26] Logic rule 0 [91] ATEX ETR cur. alarm Selectable if 1-90 Motor Thermal
[27] Logic rule 1 Protection is set to [20] or [21]. If
[28] Logic rule 2 the alarm 166 ATEX ETR
[29] Logic rule 3 freq.lim.alarm is active, the output
[30] SL Time-out 0 will be 1.
[31] SL Time-out 1 [92] ATEX ETR freq. warning Selectable if 1-90 Motor Thermal
[32] SL Time-out 2 Protection is set to [20] or [21]. If
[33] Digital input DI18 the alarm 163 ATEX ETR
[34] Digital input DI19 cur.lim.warning is active, the
[35] Digital input DI27 output will be 1.
[36] Digital input DI29 [93] ATEX ETR freq. alarm Selectable if 1-90 Motor Thermal
[37] Digital input DI32 Protection is set to [20] or [21]. If
[38] Digital input DI33 the warning 165 ATEX ETR
[39] Start command freq.lim.warning is active, the
[40] Drive stopped output will be 1.
[41] Reset Trip
[94] RS Flipflop 0
[42] Auto-reset Trip
[95] RS Flipflop 1
[43] Ok key
[96] RS Flipflop 2
[44] Reset key
[97] RS Flipflop 3
[45] Left key
[98] RS Flipflop 4
[46] Right key
[99] RS Flipflop 5
[47] Up key
[100] RS Flipflop 6
[48] Down key
[101] RS Flipflop 7
[50] Comparator 4
[51] Comparator 5 13-52 SL Controller Action
[60] Logic rule 4 Array [20]
[61] Logic rule 5 Option: Function:
[70] SL Time-out 3
[0] * DISABLED Select the action corresponding to the SLC
[71] SL Time-out 4 event. Actions are executed when the
[72] SL Time-out 5 corresponding event (defined in 13-51 SL
[73] SL Time-out 6 Controller Event) is evaluated as true. The
[74] SL Time-out 7 following actions are available for selection:
[75] Start command given
*DISABLED [0]
[76] Digital input x30/2
[77] Digital input x30/3 [1] No action No action [1]

3-124 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

13-52 SL Controller Action 13-52 SL Controller Action

Array [20] Array [20]
Option: Function: Option: Function:
[2] Select set-up
1
Select set-up 1 [2] - changes the active set-
up (0-10 Active Set-up) to ‘1’.
[14] Select preset
ref 4
Select preset reference 4 [14] – selects preset
reference 4.
3 3
If the set-up is changed, it will merge with If the active preset reference is changed, it
other set-up commands coming from either will merge with other preset reference
the digital inputs or via a serial communi- commands coming from either the digital
cation bus. inputs or via a serial communication bus.

[3] Select set-up Select set-up 2 [3] - changes the active set- [15] Select preset Select preset reference 5 [15] – selects preset
2 up 0-10 Active Set-up) to ‘2’. ref 5 reference 5.
If the set-up is changed, it will merge with If the active preset reference is changed, it
other set-up commands coming from either will merge with other preset reference
the digital inputs or via a serial communi- commands coming from either the digital
cation bus. inputs or via a serial communication bus.

[4] Select set-up Select set-up 3 [4] - changes the active set- [16] Select preset Select preset reference 6 [16] – selects preset
3 up (0-10 Active Set-up) to ‘3’. ref 6 reference 6.
If the set-up is changed, it will merge with If the active preset reference is changed, it
other set-up commands coming from either will merge with other preset reference
the digital inputs or via a serial communi- commands coming from either the digital
cation bus. inputs or via a serial communication bus.

[5] Select set-up Select set-up 4 [5] - changes the active set- [17] Select preset Select preset reference 7 [17] - selects preset
4 up (0-10 Active Set-up) to ‘4’. ref 7 reference 7.
If the set-up is changed, it will merge with If the active preset reference is changed, it
other set-up commands coming from either will merge with other preset reference
the digital inputs or via a serial communi- commands coming from either the digital
cation bus. inputs or via a serial communication bus.

[10] Select preset Select preset reference 0 [10] – selects preset [18] Select ramp 1 Select ramp 1 [18] - selects ramp 1.
ref 0 reference 0.
[19] Select ramp 2 Select ramp 2 [19] - selects ramp 2.
If the active preset reference is changed, it
will merge with other preset reference [20] Select ramp 3 Select ramp 3 [20] - selects ramp 3.
commands coming from either the digital [21] Select ramp 4 Select ramp 4 [21] - selects ramp 4.
inputs or via a serial communication bus.
[22] Run Run [22] - issues a start command to the
[11] Select preset Select preset reference 1 [11] – selects preset Adjustable frequency drive.
ref 1 reference 1.
[23] Run reverse Run reverse [23] - issues a start reverse
If the active preset reference is changed, it
command to the Adjustable frequency
will merge with other preset reference
drive.
commands coming from either the digital
inputs or via a serial communication bus. [24] Stop Stop [24] - issues a stop command to the
Adjustable frequency drive.
[12] Select preset Select preset reference 2 [12] – selects preset
ref 2 reference 2. [25] Qstop Q stop [25] - issues a quick stop command
If the active preset reference is changed, it to the Adjustable frequency drive.
will merge with other preset reference
[26] Dcstop Dcstop [26] - issues a DC stop command to
commands coming from either the digital
the Adjustable frequency drive.
inputs or via a serial communication bus.
[27] Coast Coast [27] - the Adjustable frequency drive
[13] Select preset Select preset reference 3 [13] – selects preset
coasts immediately. All stop commands
ref 3 reference 3.
including the coast command stop the SLC.
If the active preset reference is changed, it
will merge with other preset reference [28] Freeze output Freeze output [28] - freezes the output
commands coming from either the digital frequency of the Adjustable frequency
inputs or via a serial communication bus. drive.

MG33MD22 - VLT® is a registered Danfoss trademark 3-125

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

13-52 SL Controller Action 13-52 SL Controller Action

Array [20] Array [20]
Option: Function: Option: Function:

3 3 [29] Start timer 0 Start timer 0 [29] - starts timer 0, see

13-20 SL Controller Timer for further
[72] Start timer 5 Start Timer 5 [72] - Start Timer 5, see
13-20 SL Controller Timer for further
description. description.

[30] Start timer 1 Start timer 1 [30] - starts timer 1, see [73] Start timer 6 Start Timer 6 [73] - Start Timer 6, see
13-20 SL Controller Timer for further 13-20 SL Controller Timer for further
description. description.

[31] Start timer 2 Start timer 2 [31] - starts timer 2, see [74] Start timer 7 Start Timer 7 [74] - Start Timer 7, see
13-20 SL Controller Timer for further p13-20 SL Controller Timer for further
description. description.

[32] Set digital out Set digital output A low [32] - any output
A low with SL output A will be low.

[33] Set digital out Set digital output B low [33] - any output
B low with SL output B will be low.

[34] Set digital out Set digital output C low [34] - any output
C low with SL output C will be low.

[35] Set digital out Set digital output D low [35] - any output
D low with SL output D will be low.

[36] Set digital out Set digital output E low [36] - any output
E low with SL output E will be low.

[37] Set digital out Set digital output F low [37] - any output
F low with SL output F will be low.

[38] Set digital out Set digital output A high [38] - any output
A high with SL output A will be high.

[39] Set digital out Set digital output B high [39] - any output
B high with SL output B will be high.

[40] Set digital out Set digital output C high [40] - any output
C high with SL output C will be high.

[41] Set digital out Set digital output D high [41] - any output
D high with SL output D will be high.

[42] Set digital out Set digital output E high [42] - any output
E high with SL output E will be high.

[43] Set digital out Set digital output F high [43] - any output
F high with SL output Fwill be high.

[60] Reset Counter Reset Counter A [60] - resets Counter A to

A zero.

[61] Reset Counter Reset Counter B [61] - resets Counter B to

B zero.

[70] Start timer 3 Start Timer 3 [70] - Start Timer 3, see

13-20 SL Controller Timer for further
description.

[71] Start timer 4 Start Timer 4 [71] - Start Timer 4, see

13-20 SL Controller Timer for further
description.

3-126 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.15 Parameters: 14-** Special Functions NOTE!

The output frequency value of the Adjustable frequency
3.15.1 14-0* Inverter Switching drive must never exceed 1/10 of the switching frequency.
When the motor is running, adjust the switching frequency
14-00 Switching Pattern in 4-11 Motor Speed Low Limit [RPM] until the motor is as 3 3
Option: Function: noiseless as possible. See also 14-00 Switching Pattern and
[0] * 60 AVM Select the switching pattern: 60° AVM or SFAVM.
the section Special conditions in the VLT AutomationDrive
Design Guide, MG33BXYY.
[1] * SFAVM

NOTE! NOTE!
The output frequency value of the Adjustable frequency Switching frequencies higher than 5.0 kHz lead to
drive must never exceed 1/10 of the switching frequency. automatic derating of the maximum output of the
When the motor is running, adjust the switching frequency Adjustable frequency drive.
in 4-11 Motor Speed Low Limit [RPM] until the motor is as
noiseless as possible. See also 14-00 Switching Pattern and 14-03 Overmodulation
the section Special Conditions in the VLT AutomationDrive
Option: Function:
Design Guide, MG33BXYY.
[0] Off Select Off [0] for no overmodulation of the output
voltage, in order to avoid torque ripple on the
14-01 Switching Frequency motor shaft. This feature may be useful for
Select the inverter switching frequency. Changing the switching applications such as grinding machines.
frequency can help to reduce acoustic noise from the motor.
[1] * On Select On [1] to enable the overmodulation
Default depend on power size.
function for the output voltage. This is the right
Option: Function: choice when it is required that the output voltage
[0] 1.0 kHz is higher than 95% of the input voltage (typical
[1] 1.5 kHz Default switching frequency for when running oversynchronously). The output
500–1,600 hp [355–1,200 kW], 690 voltage is increased according to the degree of
V overmodulation.

[2] 2.0 kHz Default switching frequency for Overmodulation leads to increased torque ripple
350–1,075 hp [250–800 kW], 400 V as harmonics are increased.
and 50–400 hp [37–315 kW], 690 V

[3] 2.5 kHz Control in FLUX mode provides an output current

of up to 98% of the input current, regardless of
[4] 3.0 kHz Default switching frequency for
14-03 Overmodulation.
25–50 hp [18.5–37 kW], 200 V and
50–300 hp [37–200 kW], 400 V [2] Optimal

[5] 3.5 kHz 14-04 PWM Random

[6] 4.0 kHz Default switching frequency for
Option: Function:
7.5–20 hp [5.5–15 kW], 200 V and
[0] * Off No change of the acoustic motor switching noise.
15–40 hp [11–30 kW], 400 V
[1] On Transforms the acoustic motor switching noise from a
[7] * 5.0 kHz Default switching frequency for
clear ringing tone to a less noticeable ‘white’ noise.
0.34 - 4.96 kW hp [0.25–3.7 kW],
This is achieved by slightly and randomly altering the
200 V and 0.496–10 hp [0.37–7.5
synchronism of the pulse width modulated output
kW], 400 V
phases.
[8] 6.0 kHz
[9] 7.0 kHz 14-06 Dead Time Compensation
[10] 8.0 kHz
Option: Function:
[11] 10.0 kHz
[0] Off No compensation.
[12] 12.0 kHz
[13] 14.0 kHz [1] * On Activates dead time compensation.
[14] 16.0 kHz

MG33MD22 - VLT® is a registered Danfoss trademark 3-127

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.15.2 14-1* Mains On/Off 14-10 Mains Failure

Option: Function:
Parameters for configuring line failure monitoring and
handling. If a line failure appears, the Adjustable frequency
3 3 drive will try to continue in a controlled way until the
power in the DC link has been exhausted.

14-10 Mains Failure

Option: Function:
14-10 Mains Failure is typically used where very 1. The power is back before the energy
short line power interruptions (voltage dips) from DC / moment of inertia from
are present. At 100% load and a short voltage load is too low. The Adjustable
interruption, the DC voltage on the main frequency drive will perform a
capacitors drops quickly. For larger drives it controlled ramp-down when
only takes a few milliseconds before the DC 14-11 Mains Voltage at Mains Fault
level is down to about 373 V DC and the main level has been reached.
IGBT cuts off and looses the control over the 2. The Adjustable frequency drive will
motor. When the mains is restored, and the perform a controlled ramp-down as
IGBT starts again, the output frequency and long as energy in the DC link is
voltage vector does not correspond to the present. After this point, the motor
speed/frequency of the motor, and the result is will be coasted.
normally an overvoltage or overcurrent, mostly
Kinetic backup:
resulting in a trip lock. 14-10 Mains Failure can
The Adjustable frequency drive will perform a
be programmed to avoid this situation.
kinetic backup. If 2-10 Brake Function is Off [0]
Select the function to which the Adjustable or AC brake [2], the ramp will follow the
frequency drive must act when the threshold overvoltage ramping. If 2-10 Brake Function is
in 14-11 Mains Voltage at Mains Fault has been [1] Resistor Brake, the ramp will follow the
reached. setting in 3-81 Quick Stop Ramp Time.
14-10 Mains Failure cannot be changed while
Kinetic Backup [4]: The Adjustable frequency
motor is running.
drive will keep on running as long as there is
Controlled ramp-down: energy in the system due to the moment of
The Adjustable frequency drive will perform a inertia produced by the load.
controlled ramp-down. If 2-10 Brake Function is
Kinetic Backup [5]: The Adjustable frequency
Off [0] or AC brake [2], the ramp will follow the
drive will ride through on speed as long as the
Overvoltage Ramping. If 2-10 Brake Function is
energy is present from moment of inertia from
[1] Resistor Brake, the ramp will follow the
the load. If the DC voltage goes below
setting in 3-81 Quick Stop Ramp Time.
14-11 Mains Voltage at Mains Fault, the
Controlled ramp-down [1]: Adjustable frequency drive will perform a trip.
After power-up, the Adjustable frequency drive
is ready for start. Controlled ramp-down and
trip [2]: After power-up, the Adjustable
frequency drive needs a reset for starting.

3-128 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

14-10 Mains Failure 14-11 Mains Voltage at Mains Fault

Option: Function: Range: Function:
NOTE! Size [180 - This parameter defines the threshold
For the best kinetic backup performance,
the advanced motor data parameters,
related* 600 V] voltage at which the selected function in
14-10 Mains Failure should be activated. 3 3
1-30 Stator Resistance (Rs) to 1-35 Main The detection level is at a factor sqrt(2) of
Reactance (Xh), must be accurate. the value in 14-11 Mains Voltage at Mains
Fault.

[0] No This selection does not present a danger to the NOTE!

* function Adjustable frequency drive, but a trip lock Note for converting between VLT 5000
would normally be the result of the short and FC 300:
voltage interruptions. Even though the setting of the AC
[1] Ctrl. ramp- This selection will keep the output frequency Line Voltage at Line Power Fault is the
down following the motor speed. The IGBT will not same for VLT 5000 and FC 300, the
lose the connection to the motor, but will detection level is different. Use the
follow the slow. This is particularly useful in following formula to obtain the same
pump applications where the inertia is low and detection level as in VLT 5000: 14-11
the friction is high. When line power is (VLT 5000 level) = Value used in VLT
restored, the output frequency will ramp the 5000 * 1.35/sqrt(2).
motor up to the reference speed (if the line
power interruption is prolonged, the controlled
14-12 Function at Mains Imbalance
ramp-down might take the output frequency
all the way down to 0 rpm, and when line Operating under severe line imbalance conditions reduces the
power is restored, the application is ramped up lifetime of the motor. Conditions are considered severe if the
from 0 rpm to the previous reference speed via motor operates continuously near nominal load (such as when a
the normal ramp-up). pump or fan runs near full speed).

[2] Ctrl. ramp-

Option: Function:
down, trip [0] * Trip Trips the Adjustable
[3] Coasting Centrifuges can run for an hour without power frequency drive
supply. In those situations, it is possible to [1] Warning Issues a warning.
select a coast function at line power
[2] Disabled No action
interruption, together with a flying start which
occurs when line power is restored.
14-14 Kin. Backup Time Out
[4] Kinetic Kinetic backup will maintain the DC level as
Range: Function:
back-up long as possible, by converting the mechanical
60 s* [0 - 60 This parameter defines the Kinetic Backup
energy from the motor to the DC level supply.
s] Timeout in flux mode when running on low
Fans normally can extend line power
voltage grids. If the supply voltage does not
interruptions for several seconds. Pumps can
increase above the value defined in 14-11 Mains
normally only extend the interruptions for 1-2
Voltage at Mains Fault + 5% within the specified
seconds or fractions of seconds. Compressors
time, the drive will then automatically run a
only for fractions of seconds.
controlled ramp-down profile prior to stop.
[5] Kinetic
back-up, Parameters for configuring auto reset handling, special trip
trip handling and control card self test or initialization.
[6] Alarm
14-20 Reset Mode
[7] Kin. back-
Option: Function:
up, trip w
recovery Select the reset function after
tripping. Once reset, the Adjustable
frequency drive can be restarted.

MG33MD22 - VLT® is a registered Danfoss trademark 3-129

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

14-20 Reset Mode 14-22 Operation Mode

Option: Function: Option: Function:
[0] * Manual reset Select Manual reset [0], to perform a Use this parameter to specify normal

3 3 reset via [RESET] or via the digital

inputs.
operation, to perform tests, or to initialize all
parameters except 15-03 Power Up's,
15-04 Over Temp's and 15-05 Over Volt's. This
[1] Automatic reset x 1 Select Automatic reset x 1…x20 [1]-
function is active only when the power is
[12] to perform between one and
cycled to the Adjustable frequency drive.
twenty automatic resets after
Select Normal operation [0] for normal
tripping.
operation of the Adjustable frequency drive
[2] Automatic reset x 2 with the motor in the selected application.
[3] Automatic reset x 3 Select Control card test [1] to test the analog
[4] Automatic reset x 4 and digital inputs and outputs and the +10 V
[5] Automatic reset x 5 control voltage. The test requires a test
[6] Automatic reset x 6 connector with internal connections. Use the
[7] Automatic reset x 7 following procedure for the control card test:
[8] Automatic reset x 8 1. Select Control card test [1].
[9] Automatic reset x 9
2. Disconnect the line power supply
[10] Automatic reset x 10
and wait for the light in the display
[11] Automatic reset x 15
to go out.
[12] Automatic reset x 20
3. Set switches S201 (A53) and S202
[13] Infinite auto reset Select Infinite Automatic Reset [13] for
(A54) = ‘ON’ / I.
continuous resetting after tripping.
4. Insert the test plug (see below).
[14] Reset at power-up
5. Connect to the line power supply.
NOTE! 6. Carry out various tests.
The motor may start without warning. If the specified
number of AUTOMATIC RESETs is reached within 10 7. The results are displayed on the LCP
minutes, the Adjustable frequency drive enters Manual and the Adjustable frequency drive
reset [0] mode. After the Manual reset is performed, the moves into an infinite loop.
setting of 14-20 Reset Mode reverts to the original 8. 14-22 Operation Mode is automat-
selection. If the number of automatic resets is not reached ically set to Normal operation. Carry
within 10 minutes, or when a manual reset is performed, out a power cycle to start up in
the internal AUTOMATIC RESET counter returns to zero. normal operation after a control card
test.
NOTE!
Automatic reset will also be active for resetting safe stop If the test is OK
function in firmware version < 4.3x. LCP readout: Control Card OK.
Disconnect the line power supply and remove
the test plug. The green LED on the control
14-21 Automatic Restart Time
card will light up.
Range: Function:
If the test fails
10 s* [0 - 600 s] Enter the time interval from trip to start of
LCP readout: Control Card I/O failure.
the automatic reset function. This parameter
Replace the Adjustable frequency drive or
is active when 14-20 Reset Mode is set to
control card. The red LED on the control card
Automatic reset [1] - [13].
is turned on. Test plugs (connect the
following terminals to each other): 18 - 27 -
NOTE! 32; 19 - 29 - 33; 42 - 53 - 54
Remember to set switches S201 (A53) and S202 (A54) as
specified below when performing a control card test in
14-22 Operation Mode [1]. Otherwise, the test will fail!

3-130 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

14-22 Operation Mode 14-25 Trip Delay at Torque Limit

Option: Function: Range: Function:
setting the parameter to 60 sec. = OFF. Thermal

130BA097.12
3 3
12 13 18 19 27 29 32 33 20 37
FC 302 monitoring of the Adjustable frequency drive will
still remain active.

14-26 Trip Delay at Inverter Fault

Range: Function:
12 13 18 19 27 32 33 20
FC 301 Application [0 - When the Adjustable frequency drive
dependent* 35 s] detects an overvoltage in the set time,
tripping will be effected after the set
time.
39 42 50 53 54 55 If value = 0, protection mode is disabled
FC 301 &
FC 302
NOTE!
It is recommended to disable
protection mode in hoisting
Select Initialization [2] to reset all parameter applications.
values to default settings, except for
15-03 Power Up's, 15-04 Over Temp's, and 0. s* [0 - When the Adjustable frequency drive
15-05 Over Volt's. The Adjustable frequency 35 s] detects an overvoltage in the set time,
drive will reset during the next power-up. tripping will be effected after the set
14-22 Operation Mode will also revert to the time.
default setting Normal operation [0]. If value = 0, protection mode is disabled
[0] * Normal NOTE!
operation
It is recommended to disable
[1] Control protection mode in hoisting
card test applications.
[2] Initialisation
[3] Boot mode
14-29 Service Code
14-24 Trip Delay at Current Limit
Range: Function:
Range: Function:
0* [-2147483647 - 2147483647 ] For internal service only.
60 s* [0 - 60 Enter the current limit trip delay in seconds.
s] When the output current reaches the current
limit (4-18 Current Limit), a warning is triggered. 3.15.3 14-3* Current Limit Control
When the current limit warning has been contin-
uously present for the period specified in this The Adjustable frequency drive features an integral current
parameter, the Adjustable frequency drive trips. limit controller which is activated when the motor current,
Disable the trip delay by setting the parameter and thus the torque, is higher than the torque limits set in
to 60 sec. = OFF. Thermal monitoring of the 4-16 Torque Limit Motor Mode and 4-17 Torque Limit
Adjustable frequency drive will still remain active. Generator Mode.
When the current limit is reached during motor operation
14-25 Trip Delay at Torque Limit or regenerative operation, the Adjustable frequency drive
Range: Function: will try to reduce torque below the preset torque limits as
60 s* [0 - Enter the torque limit trip delay in seconds. quickly as possible without losing control of the motor.
60 s] When the output torque reaches the torque While the current control is active, the Adjustable
limits (4-16 Torque Limit Motor Mode and frequency drive can only be stopped by setting a digital
4-17 Torque Limit Generator Mode), a warning is input to Coast inverse [2] or Coast and reset inv. [3]. Any
triggered. When the torque limit warning has signal on terminals 18 to 33 will not be active until
been continuously present for the period theAdjustable frequency drive is no longer near the
specified in this parameter, the Adjustable current limit.
frequency drive trips. Disable the trip delay by

MG33MD22 - VLT® is a registered Danfoss trademark 3-131

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

By using a digital input set to Coast inverse [2] or Coast NOTE!

and reset inv. [3], the motor does not use the ramp-down This parameter is not active when1-10 Motor Construction is
time, since the Adjustable frequency drive is coasted. If a set to [1] PM non-salient SPM.
quick stop is necessary, use the mechanical brake control
3 3 function along with an external electro-mechanical brake
attached to the application.
14-41 AEO Minimum Magnetisation
Range: Function:
14-30 Current Lim Ctrl, Proportional Gain
Size related* [40 - 75 Enter the minimum allowable magnet-
Range: Function: %] ization for AEO. Selection of a low
100 %* [0 - 500 %] Enter the proportional gain value for the value reduces energy loss in the
current limit controller. Selection of a high motor, but can also reduce resistance
value makes the controller react faster. Too to sudden load changes.
high a setting leads to controller
instability. NOTE!
This parameter is not active when1-10 Motor Construction is
14-31 Current Lim Ctrl, Integration Time set to [1] PM non-salient SPM.
Range: Function:
Size related* [0.002 - Controls the current limit control 14-42 Minimum AEO Frequency
2.000 s] integration time. Setting it to a Range: Function:
lower value makes it react faster. A
10 Hz* [5 - 40 Hz] Enter the minimum frequency at which the
setting too low leads to control
Automatic Energy Optimization (AEO) is to
instability.
be active.

14-32 Current Lim Ctrl, Filter Time

NOTE!
Range: Function: This parameter is not active when1-10 Motor Construction is
1.0 ms* [1.0 - 100.0 ms] set to [1] PM non-salient SPM.
14-35 Stall Protection
14-43 Motor Cosphi
Option: Function:
Select Enable [1] to enable the stall protection in Range: Function:
field-weakening in flux mode. Select Disable [0] if Application [0.40 - The Cos(phi) setpoint is automatically
you desire to disable it. This might cause the dependent* 0.95 ] set for optimum AEO performance.
motor to be lost. 14-35 Stall Protection is active in This parameter should normally not be
flux mode only. altered. However, in some situations it
may be necessary to enter a new
[0] Disabled
value to fine tune.
[1] * Enabled
Application [0.40 - The Cos(phi) setpoint is automatically
dependent* 0.95 ] set for optimum AEO performance.
3.15.4 14-4* Energy Optimizing This parameter should normally not be
altered. However, in some situations it
Parameters for adjusting the energy optimization level in may be necessary to enter a new
both Variable Torque (VT) and Automatic Energy Optimi- value to fine tune.
zation (AEO) mode in 1-03 Torque Characteristics.

14-40 VT Level
Range: Function:
66 %* [40 - 90 %]

NOTE!
This parameter cannot be adjusted while the motor is
running.

3-132 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.15.5 14-5* Environment 14-53 Fan Monitor

Option: Function:
These parameters help the Adjustable frequency drive to Select which reaction the Adjustable frequency
operate under special environmental conditions.

14-50 RFI Filter [0] Disabled

drive should take in case a fan fault is detected.
3 3
This parameter is only available for FC 302. It is not relevant toFC [1] * Warning
301 due to different design and shorter motor cables. [2] Trip
Option: Function:
14-55 Output Filter
[0] Off Select Off [0] if the Adjustable frequency drive is fed
Option: Function:
by an isolated line power source (IT line power).
If a filter is used, select Off [0] during charging to Select the type of output filter connected. This
prevent a high leakage current making the RCD parameter cannot be adjusted while motor is
switch. running.
In this mode, the internal RFI filter capacitors between [0] No This is the default setting and should be used with
chassis and the line power RFI filter circuit are cut-out * Filter dU/dt filters or high frequency common mode (HF-
to reduce the ground capacity currents. CM) filters.
[1] * On Select On [1] to ensure that the Adjustable frequency [1] Sine- This setting is only for backwards compatibility. It
drive complies with EMC standards. Wave enables operation with FLUX control principle
Filter when the parameters 14-56 Capacitance Output
Filter and 14-57 Inductance Output Filter are
130BB908.10

programmed with the output filter capacitance

and inductance. It DOES NOT limit the range of
the switching frequency.

[2] Sine- This parameter sets a minimum allowed limit to

Wave the switching frequency and ensures that the filter
Filter will be operated within the safe range of switching
Fixed frequencies. Operation is possible with all control
principles. For the FLUX control principle, the
parameters 14-56 Capacitance Output Filter and
14-57 Inductance Output Filter have to be
14-51 DC Link Compensation programmed (these parameters have no effect in
Option: Function: VVCplus and U/f). The modulation patter will be set
to SFAVM which gives the lowest acoustic noise in
[0] Off Disables DC Link Compensation.
the filter. Remember to always set 14-55 Output
[1] * On Enables DC Link Compensation. Filter to sine-wave fixed when you use a sine-wave
filter.
14-52 Fan Control
Select minimum speed of the main fan. 14-56 Capacitance Output Filter
Option: Function: Compensation function of the LC filter requires the per phase
[0] * Auto Select Auto [0] to run fan only when equivalent star connected capacitance of the filter (3 times the
internal temperature in Adjustable capacity between two phases when capacitance is ’Delta’
frequency drive is in the range 95°F connection).
[35°C] to approx. 131°F [55°C]. Range: Function:
Fan runs at low speed below 95°F Application [0.1 - 6500.0 Set the capacitance of
[35°C], and at full speed at approx. dependent* uF] the output filter. The
131°F [55°C]. value can be found on
[1] On 50% the filter label.

[2] On 75%
[3] On 100%
[4] Auto (Low temp
env.)

MG33MD22 - VLT® is a registered Danfoss trademark 3-133

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

14-56 Capacitance Output Filter 14-74 Leg. Ext. Status Word

Compensation function of the LC filter requires the per phase Range: Function:
equivalent star connected capacitance of the filter (3 times the 0* [0 - 4294967295 ] Read out the ext. status word
capacity between two phases when capacitance is ’Delta’
3 3 connection).
corresponding to VLT 5000

Range: Function:
3.15.7 14-8* Options
NOTE!
This is required for
14-80 Option Supplied by External 24VDC
correct compensation
in flux mode Option: Function:
(1-01 Motor Control [0] No Select No [0] to use the adjustable frequency drive's
Principle) 24V DC supply.

[1] * Yes Select Yes [1] if an external 24V DC supply will be

Application [0.1 - 6500.0 used to power the option. Inputs/outputs will be
dependent* uF] galvanically isolated from the drive when operated
from an external supply.
14-57 Inductance Output Filter
Range: Function: NOTE!
Application [0.001 - This parameter is only changing function by performing a
dependent* 65.000 mH] power cycle.
Application [0.001 - Set the inductance of the
dependent* 65.000 mH] output filter. The value can be 14-89 Option Detection
found on the filter label.
Selects the behavior of the Adjustable frequency drive when a
NOTE! change in the option configuration is detected.
This is required for correct Option: Function:
compensation in flux mode [0] * Protect Option Freezes the current settings and
(1-01 Motor Control Config. prevents unwanted changes when
Principle) missing or defective options are
detected.

[1] Enable Option Changes drive settings and is used

3.15.6 14-7* Compatibility Change when modifying the system configu-
ration. This parameter setting will
The parameters in this group are for setting of compati- return to [0] after an option change.
bility for VLT 3000, VLT 5000 to FC 300.
14-72 VLT Alarm Word 14-90 Fault Level

Option: Function: Option: Function:

[0] * Off Use this parameter to customize fault levels. Use
[0] 0–4294967295 Read out the alarm word corresponding to
[0] "Off" with caution as it will ignore all
VLT 5000.
warnings and alarms for the chosen source.
14-73 VLT Warning Word [1] Warning
Option: Function: [2] Trip
[0] 0–4294967295 Read out the warning word corresponding to [3] Trip Lock
VLT 5000.

3-134 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

Failure Alarm Off Warning Trip Trip Lock

10 V low 1 X D
24 V low 47 X D

1.8V supply low

Voltage limit
48
64
X
X D
D
3 3
Ground fault during ramping 14 D X
Ground fault 2 during cont. 45 D X
operation
Torque Limit 12 X D
Overcurrent 13 X D
Short Circuit 16 X D

Heatsink temperature 29 X D
Heatsink sensor 39 X D
Control card temperature 65 X D
Power card temperature 6 2) X D
Heatsink temperature1) 244 X D
Heatsink sensor 1) 245 X D
Power card temperature 1) 247

Table 3.3 Table for selection of choice of action when selected alarm appears
D = Default setting. x = possible selection.
1) Only high power drives
In FC small and medium A69 is only a warning

MG33MD22 - VLT® is a registered Danfoss trademark 3-135

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.16 Parameters: 15-** Drive Information NOTE!

The reset is carried out by pressing [OK].
3.16.1 15-0* Operating Data

3 3 15-00 Operating Hours

15-07 Reset Running Hours Counter
Option: Function:
Range: Function:
[0] * Do not reset
0 h* [0 - 2147483647 h] View how many hours the Adjustable
[1] Reset counter Select Reset [1] and press [OK] to reset the
frequency drive has run. The value is
Running Hours counter to zero (see
saved when the Adjustable frequency
15-01 Running Hours). This parameter cannot
drive is turned off.
be selected via the serial port, RS-485.
Select Do not reset [0] if no reset of the
15-01 Running Hours
Running Hours counter is desired.
Range: Function:
0 h* [0 - 2147483647 View how many hours the motor has
h] run. Reset the counter in 15-07 Reset 3.16.2 15-1* Data Log Settings
Running Hours Counter. The value is
saved when the Adjustable frequency The Data Log enables continuous logging of up to 4 data
drive is turned off. sources (15-10 Logging Source) at individual rates
(15-11 Logging Interval). A trigger event (15-12 Trigger
15-02 kWh Counter Event) and window (15-14 Samples Before Trigger) are used
to start and stop the logging conditionally.
Range: Function:
0 kWh* [0 - 2147483647 Registering the power consumption 15-10 Logging Source
kWh] of the motor as a mean value over Array [4]
one hour. Reset the counter in
Option: Function:
15-06 Reset kWh Counter.
Select which variables are to be
logged.
15-03 Power Up's
Range: Function: [0] * None
[15] Readout: actual setup
0* [0 - 2147483647 ] View the number of times the
[1472] Legacy Alarm Word
Adjustable frequency drive has been
powered up. [1473] Legacy Warning Word
[1474] Leg. Ext. Status Word
15-04 Over Temp's [1600] Control Word
[1601] Reference [Unit]
Range: Function:
[1602] Reference %
0* [0 - 65535 ] View the number of Adjustable frequency
[1603] Status Word
drive temperature faults which have occurred.
[1610] Power [kW]
15-05 Over Volt's [1611] Power [hp]
[1612] Motor Voltage
Range: Function:
[1613] Frequency
0* [0 - 65535 ] View the number of Adjustable frequency
[1614] Motor Current
drive overvoltages which have occurred.
[1616] Torque [Nm]
[1617] Speed [RPM]
15-06 Reset kWh Counter
[1618] Motor Thermal
Option: Function:
[1621] Torque [%] High Res.
[0] * Do not reset Select Do not reset [0] if no reset of the kWh
[1622] Torque [%]
counter is desired.
[1625] Torque [Nm] High
[1] Reset counter Select Reset [1] and press [OK] to reset the [1630] DC Link Voltage
kWh counter to zero (see 15-02 kWh [1632] Brake Energy /s
Counter). [1633] Brake Energy /2 min
[1634] Heatsink Temp.
[1635] Inverter Thermal

3-136 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

15-10 Logging Source 15-12 Trigger Event

Array [4] Select the trigger event. When the trigger event occurs, a
Option: Function: window is applied to freeze the log. The log will then retain a
specified percentage of samples before the occurrence of the
[1650] External Reference
[1651] Pulse Reference
trigger event (15-14 Samples Before Trigger). 3 3
[1652] Feedback [Unit] Option: Function:
[1657] Feedback [RPM] [19] Warning
[1660] Digital Input [20] Alarm (trip)
[1662] Analog Input 53 [21] Alarm (trip lock)
[1664] Analog Input 54 [22] Comparator 0
[1665] Analog Output 42 [mA] [23] Comparator 1
[1666] Digital Output [bin] [24] Comparator 2
[1675] Analog In X30/11 [25] Comparator 3
[1676] Analog In X30/12 [26] Logic rule 0
[1677] Analog Out X30/8 [mA] [27] Logic rule 1
[1690] Alarm Word [28] Logic rule 2
[1692] Warning Word [29] Logic rule 3
[1694] Ext. Status Word [33] Digital input DI18
[1860] Digital Input 2 [34] Digital input DI19
[3110] Bypass Status Word [35] Digital input DI27
[3470] MCO Alarm Word 1 [36] Digital input DI29
[3471] MCO Alarm Word 2 [37] Digital input DI32
[38] Digital input DI33
15-11 Logging Interval [50] Comparator 4
Range: Function: [51] Comparator 5
Size related* [ 0.000 - 0.000 ] [60] Logic rule 4
[61] Logic rule 5
15-12 Trigger Event
Select the trigger event. When the trigger event occurs, a 15-13 Logging Mode
window is applied to freeze the log. The log will then retain a Option: Function:
specified percentage of samples before the occurrence of the [0] * Log always Select Log always [0] for continuous
trigger event (15-14 Samples Before Trigger). logging.
Option: Function:
[1] Log once on Select Log once on trigger [1] to
[0] * False trigger conditionally start and stop logging using
[1] True 15-12 Trigger Event and 15-14 Samples
[2] Running Before Trigger.
[3] In range
[4] On reference 15-14 Samples Before Trigger
[5] Torque limit Range: Function:
[6] Current limit 50* [0 - 100 ] Enter the percentage of all samples prior to a
[7] Out of current range trigger event which are to be retained in the
[8] Below I low log. See also 15-12 Trigger Event and
[9] Above I high 15-13 Logging Mode.
[10] Out of speed range
[11] Below speed low
[12] Above speed high
3.16.3 15-2* Historic Log
[13] Out of feedb. range
View up to 50 logged data items via the array parameters
[14] Below feedb. low
in this parameter group. For all parameters in the group,
[15] Above feedb. high
[0] is the most recent data and [49] the oldest data. Data is
[16] Thermal warning
logged every time an event occurs (not to be confused
[17] Mains out of range
[18] Reversing

MG33MD22 - VLT® is a registered Danfoss trademark 3-137

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

with SLC events). Events in this context are defined as a 15-21 Historic Log: Value
change in one of the following areas: Array [50]
Range: Function:
1. Digital input
3 3 2. Digital outputs (not monitored in this SW release)
Status word Decimal value. See
16-03 Status Word for
3. Warning word description after
converting to binary
4. Alarm word
value.
5. Status word Control word Decimal value. See
6. Control word 16-00 Control Word for
description.
7. Extended status word
Extended Decimal value. See
Events are logged with value, and time stamp in msec. The status word 16-94 Ext. Status Word for
time interval between two events depends on how often description.
events occur (maximum once every scan time). Data
logging is continuous but if an alarm occurs, the log is
saved and the values can be viewed on the display. This 15-22 Historic Log: Time
feature is useful, for example when carrying out service Array [50]
following a trip. View the historic log contained in this
Range: Function:
parameter via the serial communication port or via the
0 ms* [0 - 2147483647 View the time at which the logged
display.
ms] event occurred. Time is measured in
15-20 Historic Log: Event ms since Adjustable frequency drive
Array [50] start. The max. value corresponds to
approx. 24 days which means that the
Range: Function:
count will restart at zero after this
0* [0 - 255 ] View the event type of the logged events.
time period.

15-21 Historic Log: Value

Array [50] 3.16.4 15-3* Alarm Log
Range: Function:
Parameters in this group are array parameters, where up to
0* [0 - View the value of the logged event.
10 fault logs can be viewed. [0] is the most recent logged
2147483647 ] Interpret the event values according to
data, and [9] the oldest. Error codes, values and time
this table:
stamp can be viewed for all logged data.
Digital input Decimal value. See
15-30 Fault Log: Error Code
16-60 Digital Input for
Array [10]
description after
converting to binary Range: Function:
value. 0* [0 - 255 ] View the error code and look up its meaning in
Digital output Decimal value. See the Troubleshooting chapter of the FC 300 Design
(not 16-66 Digital Output [bin] Guide, MG33BXYY.
monitored in for description after
this SW converting to binary 15-31 Alarm Log: Value
release) value. Array [10]
Warning word Decimal value. See
Range: Function:
16-92 Warning Word for
0* [-32767 - 32767 ] View an extra description of the error.
description.
This parameter is mostly used in
Alarm word Decimal value. See
combination with alarm 38 ‘internal
16-90 Alarm Word for
fault’.
description.

3-138 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

15-32 Alarm Log: Time 15-46 Frequency Converter Ordering No

Array [10] Range: Function:
Range: Function: 0* [0 - 0 ] View the 8-digit ordering number used for re-
0 s* [0 - 2147483647 s] View the time when the logged event
occurred. Time is measured in seconds
ordering the Adjustable frequency drive in its
original configuration. 3 3
from Adjustable frequency drive start-
up. 15-47 Power Card Ordering No
Range: Function:
0* [0 - 0 ] View the power card ordering number.
3.16.5 15-4* Drive Identification
15-48 LCP Id No
Parameters containing read-only information about the
Range: Function:
hardware and software configuration of the Adjustable
frequency drive. 0* [0 - 0 ] View the LCP ID number.

15-40 FC Type 15-49 SW ID Control Card

Range: Function: Range: Function:
0* [0 - 0 ] View the Adjustable frequency drive type. The 0* [0 - 0 ] View the control card software version number.
readout is identical to the FC 300 Series power field
of the type code definition, characters 1-6. 15-50 SW ID Power Card
Range: Function:
15-41 Power Section
0* [0 - 0 ] View the power card software version number.
Range: Function:
0* [0 - 0 ] View the FC type. The readout is identical to the FC 15-51 Frequency Converter Serial Number
300 Series power field of the type code definition,
Range: Function:
characters 7-10.
0* [0 - 0 ] View the Adjustable frequency drive serial number.

15-42 Voltage
15-53 Power Card Serial Number
Range: Function:
Range: Function:
0* [0 - 0 ] View the FC type. The readout is identical to the FC
0* [0 - 0 ] View the power card serial number.
300 Series power field of the type code definition,
characters 11-12.
15-59 CSIV Filename
15-43 Software Version Range: Function:
Range: Function: Application [0 - 0 ] Shows the currently used CSIV
dependent* (Costumer Specific Initial Values)
0* [0 - 0 ] View the combined SW version (or ‘package
filename.
version’) consisting of power SW and control SW.

15-44 Ordered Typecode String 3.16.6 15-6* Option Ident.

Range: Function:
0* [0 - 0 ] View the type code string used for re-ordering the This read-only parameter group contains information about
Adjustable frequency drive in its original configu- the hardware and software configuration of the options
ration. installed in slots A, B, C0 and C1.

15-60 Option Mounted

15-45 Actual Typecode String
Range: Function:
Range: Function:
0* [0 - 0 ] View the installed option type.
0* [0 - 0 ] View the actual string.

15-61 Option SW Version

Range: Function:
0* [0 - 0 ] View the installed option software version.

MG33MD22 - VLT® is a registered Danfoss trademark 3-139

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

15-62 Option Ordering No

Range: Function:
0* [0 - 0 ] Shows the ordering number for the installed

3 3 options.

15-63 Option Serial No

Range: Function:
0* [0 - 0 ] View the installed option serial number.

15-92 Defined Parameters

Array [1000]
Range: Function:
0* [0 - 9999 ] View a list of all defined parameters in the
Adjustable frequency drive. The list ends with 0.

15-93 Modified Parameters

Array [1000]
Range: Function:
0* [0 - 9999 ] View a list of the parameters that have been
changed from their default setting. The list
ends with 0. Changes may not be visible until
up to 30 sec. after implementation.

15-99 Parameter Metadata

Array [30]
Range: Function:
0* [0 - 9999 ] This parameter contains data used by the MCT
10 Set-up Software.

3-140 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.17 Parameters: 16-** Data Read-outs 16-10 Power [kW]

Range: Function:
16-00 Control Word
30ms may pass from when an input value
Range: Function:
0* [0 - 65535 ] View the control word sent from the
changes to when the data readout values
change. The resolution of readout value 3 3
Adjustable frequency drive via the serial on serial communication bus is in 10 W
communication port in hex code. steps.

16-01 Reference [Unit] 16-11 Power [hp]

Range: Function: Range: Function:
0.000 Reference- [-999999.000 - View the present 0.00 [0.00 - View the motor power in HP. The value
FeedbackUnit* 999999.000 reference value applied hp* 10000.00 hp] shown is calculated on the basis of the
ReferenceFeed- on impulse or analog actual motor voltage and motor current.
backUnit] basis in the unit The value is filtered, and therefore
resulting from the approximately 30ms may pass from
configuration selected when an input value changes to when
in 1-00 Configuration the data readout values change.
Mode (Hz, Nm or RPM).
16-12 Motor Voltage
16-02 Reference [%] Range: Function:
Range: Function: 0.0 V* [0.0 - 6000.0 V] View the motor voltage, a calculated
0.0 %* [-200.0 - 200.0 %] value used for controlling the motor.

16-03 Status Word

16-13 Frequency
Range: Function:
Range: Function:
0* [0 - 65535 ] View the status word sent from the Adjustable
0.0 Hz* [0.0 - 6500.0 Hz] View the motor frequency, without
frequency drive via the serial communication
resonance dampening.
port in hex code.

16-14 Motor Current

16-05 Main Actual Value [%]
Range: Function:
Range: Function:
0.00 A* [0.00 - View the motor current measured as a
0.00 %* [-100.00 - 100.00 View the two-byte word sent with
10000.00 A] mean value, IRMS. The value is filtered,
%] the status word to the bus master
and thus approximately 30ms may pass
reporting the main actual value.
from when an input value changes to
when the data readout values change.
16-09 Custom Readout
Range: Function: 16-15 Frequency [%]
0.00 CustomRea- [0.00 - 0.00 View the value of custom Range: Function:
doutUnit* CustomRea- readout from 0-30 Unit for
0.00 %* [-100.00 - 100.00 %]
doutUnit] User-defined Readout to
0-32 Custom Readout Max 16-16 Torque [Nm]
Value Range: Function:
0.0 [-3000.0 - View the torque value with sign, applied to
3.17.1 16-1* Motor Status Nm* 3000.0 the motor shaft. Linearity is not exact
Nm] between 160% motor current and torque in
relation to the rated torque. Some motors
16-10 Power [kW]
supply more than 160% torque.
Range: Function: Consequently, the min. value and the max.
0.00 [0.00 - Displays motor power in kW. The value value will depend on the max. motor current
kW* 10000.00 shown is calculated on the basis of the as well as the motor used. The value is
kW] actual motor voltage and motor current. filtered, and thus approx. 30ms may pass
The value is filtered, and therefore approx.

MG33MD22 - VLT® is a registered Danfoss trademark 3-141

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

16-16 Torque [Nm] 3.17.2 16-3* Drive Status

Range: Function:
from when an input changes value to when 16-30 DC Link Voltage

3 3 the data readout values change. Range:

0 V*
Function:
[0 - 10000 V] View a measured value. The value is filtered
16-17 Speed [RPM] with an 30ms time constant.
Range: Function:
0 RPM* [-30000 - View the actual motor RPM. In open- 16-32 Brake Energy /s
30000 RPM] loop or closed-loop process control, the Range: Function:
motor RPM is estimated. In speed 0.000 kW* [0.000 - 10000.000 View the braking energy
closed-loop modes, the motor RPM is kW] transmitted to an external brake
measured. resistor, stated as an instan-
taneous value.
16-18 Motor Thermal
Range: Function: 16-33 Brake Energy /2 min
0 %* [0 - 100 %] View the calculated thermal load on the Range: Function:
motor. The cut-out limit is 100%. The basis 0.000 kW* [0.000 - View the braking energy
for calculation is the ETR function selected in 10000.000 kW] transmitted to an external brake
1-90 Motor Thermal Protection. resistor. The mean power is
calculated on an average basis for
16-19 KTY sensor temperature the most recent 120 sec.
Range: Function:
0 C* [0 - 0 C] 16-34 Heatsink Temp.
Range: Function:
16-20 Motor Angle
0 °C* [0 - 255 °C]
Range: Function:
0* [0 - 65535 ] View the current encoder/resolver angle offset 16-35 Inverter Thermal
relative to the index position. The value range Range: Function:
of 0-65535 corresponds to 0-2*pi (radians). 0 %* [0 - 100 %] View the percentage load on the inverter.

16-21 Torque [%] High Res. 16-36 Inv. Nom. Current

Range: Function: Range: Function:
0.0 %* [-200.0 - 200.0 %] Application [0.01 - View the inverter nominal
dependent* 10000.00 A] current, which should match the
16-22 Torque [%]
nameplate data on the
Range: Function: connected motor. The data are
0 %* [-200 - 200 %] Value shown is the torque as a used for calculation of torque,
percentage of nominal torque, with sign, motor protection, etc.
applied to the motor shaft.
Application [0.01 - View the inverter nominal
dependent* 10000.00 A] current, which should match the
16-25 Torque [Nm] High
nameplate data on the
Range: Function: connected motor. The data are
0.0 [-200000000.0 - View the torque value with sign, used for calculation of torque,
Nm* 200000000.0 Nm] applied to the motor shaft. Some motor protection, etc.
motors supply more than 160%
torque. Consequently, the min. value 16-37 Inv. Max. Current
and the max. value will depend on
Range: Function:
the max. motor current as well as the
Application [0.01 - View the inverter maximum
motor used. This specific readout has
dependent* 10000.00 A] current, which should match the
been adapted to show higher values
nameplate data on the
than the standard readout in
16-16 Torque [Nm].

3-142 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

16-37 Inv. Max. Current 16-51 Pulse Reference

Range: Function: Range: Function:
connected motor. The data are can also reflect the impulses from an
used for calculation of torque,
motor protection, etc.
incremental encoder.
3 3
16-52 Feedback [Unit]
Application [0.01 - View the inverter maximum
dependent* 10000.00 A] current, which should match the Range: Function:
nameplate data on the 0.000 Reference- [-999999.999 - View the feedback unit
connected motor. The data are FeedbackUnit* 999999.999 resulting from the
used for calculation of torque, ReferenceFeed- selection of unit and
motor protection, etc. backUnit] scaling in 3-00 Reference
Range, 3-01 Reference/
16-38 SL Controller State Feedback Unit,
Range: Function: 3-02 Minimum Reference
and 3-03 Maximum
0* [0 - 100 ] View the state of the event under execution by
Reference.
the SL controller.

16-53 Digi Pot Reference

16-39 Control Card Temp.
Range: Function:
Range: Function:
0.00* [-200.00 - 200.00 ] View the contribution of the digital
0 °C* [0 - 100 °C]
potentiometer to the actual reference.
16-40 Logging Buffer Full
Option: Function: 16-57 Feedback [RPM]
View whether the logging buffer is full (see parameter Range: Function:
group 15-1*). The logging buffer will never be full 0 RPM* [-30000 - Readout parameter where the actual
when 15-13 Logging Mode is set to Log always [0]. 30000 RPM] motor RPM from the feedback source
can be read in both closed-loop and
[0] * No
open-loop. The feedback source is
[1] Yes
selected by 7-00 Speed PID Feedback
16-49 Current Fault Source Source.

Range: Function:
0* [0 - 8 ] Value indicates source of current faults including
short circuit, overcurrent, and phase imbalance
(from left):
1-4 Inverter
5-8 Rectifier
0 No fault recorded

3.17.3 16-5* Ref. & Feedb.

16-50 External Reference

Range: Function:
0.0* [-200.0 - View the total reference, the sum of
200.0 ] digital, analog, preset, bus and freeze
references, plus catch-up and slow-down.

16-51 Pulse Reference

Range: Function:
0.0* [-200.0 - View the reference value from
200.0 ] programmed digital input(s). The readout

MG33MD22 - VLT® is a registered Danfoss trademark 3-143

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.17.4 16-6* Inputs & Outputs 16-63 Terminal 54 Switch Setting

Option: Function:
16-60 Digital Input View the setting of input terminal 54. Current

3 3 0
Range:
[0 -
Function:
View the signal states from the active digital inputs. [0] * Current
= 0; Voltage = 1.

* 1023 ] Example: Input 18 corresponds to bit no. 5, ‘0’ = no [1] Voltage

signal, ‘1’ = connected signal. Bit 6 works in the [2] Pt 1000 [°C]
opposite way, on = '0', off = '1' (safe stop input).
[3] Pt 1000 [°F]
Bit 0 Digital input term. 33 [4] Ni 1000 [°C]
Bit 1 Digital input term. 32 [5] Ni 1000 [°F]
Bit 2 Digital input term. 29
16-64 Analog Input 54
Bit 3 Digital input term. 27
Range: Function:
Bit 4 Digital input term. 19
0.000* [-20.000 - 20.000 ] View the actual value at input 54.
Bit 5 Digital input term. 18
Bit 6 Digital input term. 37
16-65 Analog Output 42 [mA]
Bit 7 Digital input GP I/O term. X30/4
Range: Function:
Bit 8 Digital input GP I/O term. X30/3
Bit 9 Digital input GP I/O term. X30/2 0.000* [0.000 - 30.000 ] View the actual value at output 42 in
mA. The value shown reflects the
Bit 10-63 Reserved for future terminals
selection in 6-50 Terminal 42 Output.

0 0 0 0 0 0 0 0 0 0 0 0 0 00 00
16-66 Digital Output [bin]
130BA894.10

DI T -33
DI T -32
DI T -29 Range: Function:
DI T -27
DI T -19
0* [0 - 15 ] View the binary value of all digital outputs.
DI T -18
DI T -37
DI X30/4 16-67 Pulse Input #29 [Hz]
DI X30/3
DI X30/2 Range: Function:
DI X46/13
DI X46/11 0* [0 - 130000 ] View the actual frequency rate on terminal
DI X46/9
DI X46/7 29.
DI X46/5
DI X46/3
DI X46/1 16-68 Freq. Input #33 [Hz]
Range: Function:
0* [0 - 130000 ] View the actual value of the frequency
16-61 Terminal 53 Switch Setting
applied at terminal 33 as an impulse input.
Option: Function:
View the setting of input terminal 53. Current 16-69 Pulse Output #27 [Hz]
= 0; Voltage = 1.
Range: Function:
[0] * Current 0* [0 - 40000 ] View the actual value of pulses applied to
[1] Voltage terminal 27 in digital output mode.
[2] Pt 1000 [°C]
[3] Pt 1000 [°F] 16-70 Pulse Output #29 [Hz]
[4] Ni 1000 [°C] Range: Function:
[5] Ni 1000 [°F] 0* [0 - 40000 ] View the actual value of pulses at terminal 29
in digital output mode.
16-62 Analog Input 53
This parameter is available for FC 302 only.
Range: Function:
0.000* [-20.000 - 20.000 ] View the actual value at input 53.

3-144 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

16-71 Relay Output [bin] 16-77 Analog Out X30/8 [mA]

Range: Function: Range: Function:
0* [0 - 511 ] View the settings of all relays. 0.000 * [0.000 - 30.000 ] View the actual value at input X30/8
in mA.
3 3
16-78 Analog Out X45/1 [mA]
Range: Function:
0.000* [0.000 - 30.000 ] View the actual value at output X45/1.
The value shown reflects the selection
in 6-70 Terminal X45/1 Output.

16-79 Analog Out X45/3 [mA]

Range: Function:
0.000* [0.000 - 30.000 ] View the actual value at output X45/3.
16-72 Counter A The value shown reflects the selection
Range: Function: in 6-80 Terminal X45/3 Output.

0* [-2147483648 - View the present value of Counter A.

2147483647 ] Counters are useful as comparator 3.17.5 16-8* Serial communication bus &
operands, see 13-10 Comparator Operand. FC Port
The value can be reset or changed either
via digital inputs (parameter group 5-1*) or Parameters for reporting the BUS references and control
by using an SLC action (13-52 SL Controller words.
Action).
16-80 Fieldbus CTW 1
16-73 Counter B Range: Function:
Range: Function: 0* [0 - View the two-byte control word (CTW) received
0* [-2147483648 - View the present value of Counter B. 65535 ] from the bus master. Interpretation of the
2147483647 ] Counters are useful as comparator control word depends on the Serial
operands (13-10 Comparator Operand). communication bus option installed and the
The value can be reset or changed either control word profile selected in 8-10 Control
via digital inputs (parameter group 5-1*) or Profile.
by using an SLC action (13-52 SL Controller For more information, please refer to the
Action). relevant Serial communication bus manual.

16-74 Prec. Stop Counter 16-82 Fieldbus REF 1

Range: Function: Range: Function:
0* [0 - 2147483647 ] Returns the actual counter value of 0* [-200 - View the two-byte word sent with the control
precise counter (1-84 Precise Stop Counter 200 ] word form the bus master to set the reference
Value). value.
For more information, refer to the relevant
16-75 Analog In X30/11 serial communication bus manual.

Range: Function:
16-84 Comm. Option STW
0.000 * [-20.000 - 20.000 ] View the actual value at input
X30/11 of MCB 101.
Range: Function:
0* [0 - 65535 ] View the extended Serial communication bus
16-76 Analog In X30/12 comm. option status word.
For more information, please refer to the
Range: Function:
relevant Serial communication bus manual.
0.000 * [-20.000 - 20.000 ] View the actual value at input
X30/12 of MCB 101.

MG33MD22 - VLT® is a registered Danfoss trademark 3-145

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

16-85 FC Port CTW 1 16-96 Maintenance Word

Range: Function: Range: Function:
0* [0 - 65535 ] View the two-byte control word (CTW) 0 [0 - Readout of the Preventive Maintenance

3 3 received from the bus master. Interpretation

of the control word depends on the Serial
* 4294967295 ] Word. The bits reflect the status for the
programmed preventive maintenance events
communication bus option installed and the in parameter group 23-1*. 13 bits represent
control word profile selected in 8-10 Control combinations of all the possible items:
Profile.
• Bit 0: Motor bearings

16-86 FC Port REF 1 • Bit 1: Pump bearings

Range: Function: • Bit 2: Fan bearings

0* [-200 - View the two-byte status word (STW) sent to • Bit 3: Valve
200 ] the bus master. Interpretation of the status
• Bit 4: Pressure transmitter
word depends on the serial communication
bus option installed and the control word • Bit 5: Flow transmitter

profile selected in 8-10 Control Profile. • Bit 6: Temperature transmitter

• Bit 7: Pump seals

3.17.6 16-9* Diagnosis Readouts • Bit 8: Fan belt

• Bit 9: Filter
16-90 Alarm Word
• Bit 10: Drive cooling fan
Range: Function:
• Bit 11: Drive system health check
0* [0 - 4294967295 ] View the alarm word sent via the serial
communication port in hex code. • Bit 12: Warranty

• Bit 13: Maintenance Text 0

16-91 Alarm Word 2
• Bit 14: Maintenance Text 1
Range: Function:
• Bit 15: Maintenance Text 2
0* [0 - 4294967295 ] View the alarm word sent via the serial
communication port in hex code. • Bit 16: Maintenance Text 3

• Bit 17: Maintenance Text 4

16-92 Warning Word
Positio Valve Fan Pump Motor
Range: Function:
n 4⇒ bearing bearing bearing
0* [0 - 4294967295 ] View the warning word sent via the s s s
serial communication port in hex code.
Positio Pump Temper Flow Pressur
n3⇒ seals ature transmi e
16-93 Warning Word 2 transmi tter transmi
Range: Function: tter tter
0* [0 - 4294967295 ] View the warning word sent via the serial Positio Drive Drive Filter Fan
communication port in hex code. n2⇒ system cooling belt
health fan
16-94 Ext. Status Word check
Range: Function: Positio Warrant
0* [0 - 4294967295 ] Returns the extended warning word sent n 1⇒ y
via the serial communication port in hex 0hex - - - -
code. 1hex - - - +
2hex - - + -
16-95 Ext. Status Word 2 3hex - - + +
Range: Function: 4hex - + - -
0* [0 - 4294967295 ] Returns the extended warning word 2 5hex - + - +
sent via the serial communication port 6hex - + + -
in hex code.

3-146 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

16-96 Maintenance Word

Range: Function:
7hex - + + +
8hex
9hex
+
+
-
-
-
-
-
+
3 3
Ahex + - + -
Bhex + - + +
Chex + + - -
Dhex + + - +
Ehex + + + -
Fhex + + + +

Example:
The Preventive Maintenance Word shows
040Ahex.

Position 1 2 3 4
hex value 0 4 0 A

The first digit 0 indicates that no items from

the fourth row requires maintenance
The second digit 4 refers to the third row
indicating that the drive cooling fan requires
maintenance
The third digit 0 indicates that no items from
the second row require maintenance
The fourth digit A refers to the top row
indicating that the valve and the pump
bearings require maintenance

MG33MD22 - VLT® is a registered Danfoss trademark 3-147

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.18 Parameters: 17-** Motor Feedb. 17-21 Resolution (Positions/Rev)

Option Select the resolution of the absolute encoder, i.e., the number of
counts per revolution.
Additional parameters to configure the Encoder (MCB 102) The value depends on setting in 17-20 Protocol Selection.
3 3 or the Resolver (MCB 103) Feedback Option.
Range: Function:
Application [Application
3.18.1 17-1* Inc. Enc. Interface dependent* dependant]

Parameters in this group configure the incremental NOTE!

interface of the MCB 102 option. Note that both the This parameter cannot be adjusted while the motor is
incremental and absolute interfaces are active at the same running.
time.
17-24 SSI Data Length
NOTE! Range: Function:
These parameters cannot be adjusted while the motor is 13* [13 - 25 ] Set the number of bits for the SSI message.
running. Choose 13 bits for single-turn encoders and 25
bits for multi-turn encoder.
17-10 Signal Type
Select the incremental type (A/B channel) of the encoder in use. 17-25 Clock Rate
Find the information on the encoder data sheet. Range: Function:
Select None [0] if the feedback sensor is an absolute encoder Application [Application Set the SSI clock rate. With
only. dependent* dependant] long encoder cables the
Option: Function: clock rate must be reduced.
[0] None
[1] * RS422 (5V TTL) 17-26 SSI Data Format
[2] Sinusoidal 1Vpp Option: Function:
[0] * Gray code
17-11 Resolution (PPR)
[1] Binary code Set the data format of the SSI data. Choose
Range: Function: between Gray or Binary format.
1024* [10 - 10000 ]
17-34 HIPERFACE Baudrate
3.18.2 17-2* Abs. Enc. Interface Select the baud rate of the attached encoder.
The parameter is only accessible when 17-20 Protocol Selection is
Parameters in this group configure the absolute interface set to HIPERFACE [1].
of the MCB 102 option. Note that both the incremental Option: Function:
and absolute interfaces are active at the same time. [0] 600
17-20 Protocol Selection [1] 1200
[2] 2400
Select HIPERFACE [1] if the encoder is absolute only.
Select None [0] if the feedback sensor is an incremental encoder [3] 4800
only. [4] * 9600
[5] 19200
Option: Function:
[6] 38400
[0] * None
[1] HIPERFACE NOTE!
[2] EnDat This parameter cannot be adjusted while the motor is
[4] SSI running.

NOTE!
This parameter cannot be adjusted while the motor is
3.18.3 17-5* Resolver Interface
running.
Parameter group 17-5* is used for setting parameters for
the MCB 103 resolver option.

3-148 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

Usually the resolver feedback is used as motor feedback 17-59 Resolver Interface
from permanent magnet motors with 1-01 Motor Control Activate the MCB 103 resolver option when the resolver
Principle set to Flux with motor feedback. parameters are selected.
Resolver parameters cannot be adjusted while the motor is To avoid damage to resolvers, 17-50 Poles – 17-53 Transformation
running. Ratio must be adjusted before activating this parameter. 3 3
17-50 Poles Option: Function:
Range: Function: [0] * Disabled
2* [2 - 2 ] Set the number of poles on the resolver. [1] Enabled
The value is stated in the data sheet for resolvers.
3.18.4 17-6* Monitoring and Application
17-51 Input Voltage
Range: Function: This parameter group is used for selecting additional
7.0 V* [2.0 - 8.0 V] Set the input voltage to the resolver. The functions when the MCB 102 Encoder option or MCB 103
voltage is stated as an RMS value. Resolver option is fitted into option slot B as speed
The value is stated in the data sheet for feedback.
resolvers. Monitoring and application parameters cannot be adjusted
while the motor is running.
17-52 Input Frequency
17-60 Feedback Direction
Range: Function:
Change the detected encoder rotation direction without
10.0 kHz* [2.0 - 15.0 Set the input frequency to the changing the wiring to the encoder.
kHz] resolver.
Option: Function:
The value is stated in the data sheet
for resolvers. [0] * Clockwise
[1] Counter clockwise
17-53 Transformation Ratio
NOTE!
Range: Function: This parameter cannot be adjusted while the motor is
0.5* [0.1 - 1.1 ] Set the transformation ratio for the resolver. running.
The transformation ration is:
V Out
T ratio =
17-61 Feedback Signal Monitoring
V In
Select which reaction the Adjustable frequency drive should take
The value is stated in the data sheet for
if a faulty encoder signal is detected.
resolvers.
The encoder function in 17-61 Feedback Signal Monitoring is an
electrical check of the hardware circuit in the encoder system.
17-56 Encoder Sim. Resolution
Option: Function:
Set the resolution and activate the encoder emulation function
[0] Disabled
(generation of encoder signals from the measured position from
a resolver). Needed when necessary to transfer the speed or [1] * Warning
position information from one drive to another. To disable the [2] Trip
function, select [0]. [3] Jog
[4] Freeze Output
Option: Function:
[5] Max Speed
[0] * Disabled
[6] Switch to Open Loop
[1] 512
[7] Select Setup 1
[2] 1024
[8] Select Setup 2
[3] 2048
[9] Select Setup 3
[4] 4096
[10] Select Setup 4
[11] stop & trip

MG33MD22 - VLT® is a registered Danfoss trademark 3-149

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.19 Parameters: 18-** Data Readouts 2

18-36 Analog Input X48/2 [mA]
Range: Function:
3 3 0.000* [-20.000 - 20.000 ] View the actual current measured at
input X48/2.

18-37 Temp. Input X48/4

Range: Function:
0* [-500 - 500 ] View the actual temperature measured at
input X48/4. The temperature unit is based on
the selection in 35-00 Term. X48/4 Temp. Unit.

18-38 Temp. Input X48/7

Range: Function:
0* [-500 - 500 ] View the actual temperature measured at
input X48/7. The temperature unit is based on
the selection in 35-02 Term. X48/7 Temp. Unit.

18-39 Temp. Input X48/10

Range: Function:
0* [-500 - 500 ] View the actual temperature measured at
input X48/10. The temperature unit is based
on the selection in 35-04 Term. X48/10 Temp.
Unit.

18-60 Digital Input 2

Range: Function:
0* [0 - 65535 ] View the signal states from the active digital
inputs. '0' = no signal, '1' = connected signal.

18-90 Process PID Error

Range: Function:
0.0 %* [-200.0 - 200.0 %]

18-91 Process PID Output

Range: Function:
0.0 %* [-200.0 - 200.0 %]

18-92 Process PID Clamped Output

Range: Function:
0.0 %* [-200.0 - 200.0 %]

18-93 Process PID Gain Scaled Output

Range: Function:
0.0 %* [-200.0 - 200.0 %]

3-150 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.20 Parameters: 30-** Special Features 30-00 Wobble Mode

Option: Function:
3.20.1 30-0* Wobble Function
[3] Rel. Freq.,

The wobble function is primarily used for synthetic yarn

winding applications. The wobble option is to be installed
Up/ Down
Time 3 3
in the Adjustable frequency drive controlling the traverse NOTE!
drive. The traverse drive Adjustable frequency drive will This parameter cannot be set while running.
move the yarn back and forth in a diamond pattern across
the surface of the yarn package. To prevent a buildup of
yarn at the same points at the surface, this pattern must
NOTE!
The setting of “Center Frequency” takes place via the
be altered. The wobble option can accomplish this by
normal reference handling parameter group, 3-1*
continuously varying the traverse velocity in a
programmable cycle. The wobble function is created by
superimposing a delta frequency around a center 30-01 Wobble Delta Frequency [Hz]
frequency. To compensate for the inertia in the system a Range: Function:
quick frequency jump can be included. Especially suitable 5.0 [0.0 - The delta frequency is determining the
for elastic yarn applications, the option features a Hz* 25.0 Hz] magnitude of the wobble frequency. The delta
randomized wobble ratio. frequency is superimposed on the center
frequency. 30-01 Wobble Delta Frequency [Hz]
Frequency selects both the positive and negative delta
175ZB001.10

Par. 30-07: WOBB TIME

[Hz]
Par. 30-06: JUMP TIME
Par. 30-04 [Hz]: JUMP FREQ frequency. The setting of 30-01 Wobble Delta
Par. 30-09 [%] : JUMP FREQ
Par. 30-01 [Hz]: DELTA FREQ.
Par. 30-02 [%]: DELTA FREQ.
Frequency [Hz] must thus not be higher than
(Par. 30-03)
the setting of the center frequency. The initial
Par. 30-01 [Hz]
Par. 30-02 [%]
(Par. 30-03:)
ramp-up time from standstill until the wobble
Par. 30-*1: RAMP UP Par. 30-09: RANDOM FUNC
CENTER FREQ Par 30-11: RANDOM MAX sequence is running is determined by
Par 30-12: RANDOM MIN
TDOWN TUP parameter group 3-1*.
Par. 30-10: [RATIO TUP/ TDOWN ]
Par. 30-08: [INDEPENDENT UP and DOWN]

Time [s]
30-02 Wobble Delta Frequency [%]
Range: Function:
30-00 Wobble Mode 25 %* [0 - 100 %]
Option: Function:
30-03 Wobble Delta Freq. Scaling Resource
The standard speed open-loop mode in
Option: Function:
1-00 Configuration Mode is extended with a
wobble function. In this parameter, it is Select which drive input should be
possible to select which method to be used used to scale the delta frequency
for the wobbler. The parameters can be set setting.
as absolute values (direct frequencies) or as [0] * No function
relative values (percentage of other [1] Analog input 53
parameters). The wobble cycle time can be [2] Analog input 54
set as an absolute value or as independent [3] Frequency input 29 FC 302 only
up and down times. When using an absolute
[4] Frequency input 33
cycle time, the up and down times are
configured through the wobble ratio. [7] Analog input X30/11
[8] Analog input X30/12
[0] * Abs. Freq.,
[15] Analog Input X48/2
Abs. Time
[1] Abs. Freq., 30-04 Wobble Jump Frequency [Hz]
Up/ Down Range: Function:
Time
0.0 [Application The jump frequency is used to
[2] Rel. Freq.,
Hz* dependant] compensate for the inertia in the traverse
Abs. Time
system. If a jump in the output frequency
is required in the top and in the bottom
of the wobble sequence, the frequency

MG33MD22 - VLT® is a registered Danfoss trademark 3-151

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

30-04 Wobble Jump Frequency [Hz] 30-12 Wobble Random Ratio Min.
Range: Function: Range: Function:
jump is set in this parameter. If the 0.1* [Application dependant] Enter the minimum allowed

3 3 traverse system has a very high inertia a

high jump frequency may create a torque
wobble ratio.

limit warning or trip (warning/alarm 12) 30-19 Wobble Delta Freq. Scaled
or an overvoltage warning or trip Range: Function:
(warning/alarm 7). This parameter can
0.0 Hz* [0.0 - 1000.0 Hz] Readout parameter. View the actual
only be changed in stop mode
wobble delta frequency after scaling
has been applied.
30-05 Wobble Jump Frequency [%]
Range: Function:
0 %* [0 - 100 %] 3.20.2 30-2* Adv. Start Adjust
30-06 Wobble Jump Time 30-20 High Starting Torque Time [s]
Range: Function: Range: Function:
Application [Application This parameter determines 0.00 s* [0.00 - 60.00 s] High starting torque time for PM motor
dependent* dependant] the slope of the jump ramp in flux mode without feedback. This
at the max. and min. parameter is available for FC 302 only.
wobble frequency.
30-21 High Starting Torque Current [%]
30-07 Wobble Sequence Time
Range: Function:
Range: Function:
100.0 %* [Application High starting torque current for
10.0 s* [1.0 - 1000.0 s] This parameter determines the wobble dependant] PM motor in flux mode without
sequence period. This parameter can feedback. This parameter is
only be changed in stop mode. available for FC 302 only.
Wobble time = tup + tdown
30-22 Locked Rotor Protection
30-08 Wobble Up/ Down Time
Locked Rotor Protection for PM motor in flux mode without
Range: Function: feedback. This parameter is available for FC 302 only.
5.0 s* [0.1 - 1000.0 s] Defines the individual up and down Option: Function:
times for each wobble cycle.
[0] * Off
[1] On
30-09 Wobble Random Function
Option: Function: 30-23 Locked Rotor Detection Time [s]
[0] * Off Locked Rotor Detection Time for PM motor in flux mode without
[1] On feedback. This parameter is available for FC 302 only.
Range: Function:
30-10 Wobble Ratio
0.10 s* [0.05 - 1.00 s]
Range: Function:
1.0* [0.1 - 10.0 ] If the ratio 0.1 is selected: tdown is 10 times
greater than tup.
3.20.3 30-8* Compatibility
If the ratio 10 is selected: tup is 10 times
greater than tdown. 30-80 d-axis Inductance (Ld)
Range: Function:
30-11 Wobble Random Ratio Max. Application [Application Enter the value of the d-axis
Range: Function: dependent* dependant] inductance. Obtain the value
10.0* [Application dependant] Enter the maximum allowed from the permanent magnet
wobble ratio. motor data sheet. The d-axis
inductance cannot be found
by performing an AMA.

3-152 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

30-81 Brake Resistor (ohm)

Range: Function:
Application [Application Set the brake resistor value in
dependent* dependant] Ohms. This value is used for
monitoring the power to the 3 3
brake resistor in 2-13 Brake
Power Monitoring. This
parameter is only active in
drives with an integral dynamic
brake.

30-83 Speed PID Proportional Gain

Range: Function:
Application [0.0000 - Enter the speed controller
dependent* 1.0000 ] proportional gain. Quick control
is obtained at high amplification.
However, if the amplification is
too great, the process may
become unstable.

Application [0.0000 - Enter the speed controller

dependent* 1.0000 ] proportional gain. Quick control
is obtained at high amplification.
However, if the amplification is
too great, the process may
become unstable.

30-84 Process PID Proportional Gain

Range: Function:
0.100* [0.000 - Enter the process controller propor-
10.000 ] tional gain. Quick control is obtained at
high amplification. However, if the
amplification is too great, the process
may become unstable.

MG33MD22 - VLT® is a registered Danfoss trademark 3-153

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3.21 Parameters: 35-** Sensor Input Option 35-06 Temperature Sensor Alarm Function
Select the alarm function:
3.21.1 35-0* Temp. Input Mode (MCB 114)
Option: Function:

3 3 35-00 Term. X48/4 Temp. Unit

[0]
[2]
Off
Stop
Select the unit to be used with temperature input X48/4 settings
[5] * Stop and trip
and readouts:
Option: Function:
3.21.2 35-1* Temp. Input X48/4 (MCB 114)
[60] * °C
[160] °F
35-14 Term. X48/4 Filter Time Constant
35-01 Term. X48/4 Input Type Range: Function:
View the temperature sensor type detected at input X48/4: 0.001 s* [0.001 - Enter the filter time constant. This is a
Option: Function: 10.000 s] first-order digital low pass filter time
constant for suppressing electrical noise
[0] * Not Connected
in terminal X48/4. A high time constant
[1] PT100 2-wire
value improves dampening but also
[3] PT1000 2-wire
increases the time delay through the
[5] PT100 3-wire
filter.
[7] PT1000 3-wire

35-02 Term. X48/7 Temp. Unit 35-15 Term. X48/4 Temp. Monitor
Select the unit to be used with temperature input X48/7 settings This parameter gives the possibility of enabling or disabling the
and readouts: temperature monitor for terminal X48/4. The temperature limits
can be set in 35-16 Term. X48/4 Low Temp. Limit and 35-17 Term.
Option: Function:
X48/4 High Temp. Limit.
[60] * °C
Option: Function:
[160] °F
[0] * Disabled
35-03 Term. X48/7 Input Type [1] Enabled
View the temperature sensor type detected at input X48/7:
35-16 Term. X48/4 Low Temp. Limit
Option: Function:
Range: Function:
[0] * Not Connected
Application dependent* [Application dependant]
[1] PT100 2-wire
[3] PT1000 2-wire 35-17 Term. X48/4 High Temp. Limit
[5] PT100 3-wire Range: Function:
[7] PT1000 3-wire Application dependent* [Application dependant]

35-04 Term. X48/10 Temp. Unit

Select the unit to be used with temperature input X48/10 3.21.3 35-2* Temp. Input X48/7 (MCB 114)
settings and readouts:
Option: Function: 35-24 Term. X48/7 Filter Time Constant
[60] * °C Range: Function:
[160] °F 0.001 s* [0.001 - Enter the filter time constant. This is a
10.000 s] first-order digital low pass filter time
35-05 Term. X48/10 Input Type constant for suppressing electrical noise
View the temperature sensor type detected at input X48/10: in terminal X48/7. A high time constant
Option: Function: value improves dampening but also
increases the time delay through the
[0] * Not Connected
filter.
[1] PT100 2-wire
[3] PT1000 2-wire
[5] PT100 3-wire
[7] PT1000 3-wire

3-154 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

35-25 Term. X48/7 Temp. Monitor 3.21.5 35-4* Analog Input X48/2 (MCB 114)
This parameter gives the possibility of enabling or disabling the
temperature monitor for terminal X48/7. The temperature limits 35-42 Term. X48/2 Low Current
can be set in 35-26 Term. X48/7 Low Temp. Limit and 35-27 Term.
X48/7 High Temp. Limit.
Range:
4.00 [Application
Function:
Enter the current (mA) that
3 3
Option: Function: mA* dependant] corresponds to the low reference
[0] * Disabled value, set in 35-44 Term. X48/2 Low
[1] Enabled Ref./Feedb. Value. The value must be
set at > 2mA in order to activate the
35-26 Term. X48/7 Low Temp. Limit Live Zero Timeout Function in
Range: Function: 6-01 Live Zero Timeout Function.
Application dependent* [Application dependant]
35-43 Term. X48/2 High Current
35-27 Term. X48/7 High Temp. Limit
Range: Function:
Range: Function: 20.00 mA* [Application Enter the current (mA) that
Application dependent* [Application dependant] dependant] corresponds to the high
reference value (set in
3.21.4 35-3* Temp. Input X48/10 (MCB 114) 35-45 Term. X48/2 High Ref./Feedb.
Value).

35-34 Term. X48/10 Filter Time Constant

35-44 Term. X48/2 Low Ref./Feedb. Value
Range: Function:
Range: Function:
0.001 s* [0.001 - Enter the filter time constant. This is a
0.000* [-999999.999 - Enter the reference or feedback
10.000 s] first-order digital low pass filter time
999999.999 ] value (in RPM, Hz, bar, etc.) that
constant for suppressing electrical noise
corresponds to the voltage or
in terminal X48/10. A high time constant
current set in 35-42 Term. X48/2
value improves dampening but also
Low Current.
increases the time delay through the
filter.
35-45 Term. X48/2 High Ref./Feedb. Value
35-35 Term. X48/10 Temp. Monitor Range: Function:
This parameter gives the possibility of enabling or disabling the 100.000* [-999999.999 - Enter the reference or feedback
temperature monitor for terminal X48/10. The temperature limits 999999.999 ] value (in RPM, Hz, bar, etc.) that
can be set in 35-36 Term. X48/10 Low Temp. Limit/35-37 Term. corresponds to the voltage or
X48/10 High Temp. Limit. current set in 35-43 Term. X48/2
High Current.
Option: Function:
[0] * Disabled
35-46 Term. X48/2 Filter Time Constant
[1] Enabled
Range: Function:
35-36 Term. X48/10 Low Temp. Limit 0.001 s* [0.001 - Enter the filter time constant. This is a
Range: Function: 10.000 s] first-order digital low pass filter time
constant for suppressing electrical noise
Application dependent* [Application dependant]
in terminal X48/2. A high time constant
35-37 Term. X48/10 High Temp. Limit value improves dampening but also
Range: Function: increases the time delay through the
filter.
Application dependent* [Application dependant]

MG33MD22 - VLT® is a registered Danfoss trademark 3-155

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Descriptions FC 300 Programming Guide

3 3

3-156 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

4 Parameter Lists

FC Series Conversion index Conversion factor

All = valid for FC 301 and FC 302 series 100
01 = valid for FC 301 only 75
02 = valid for FC 302 only 74
67
4 4
Changes during operation 6 1000000
”TRUE” means that the parameter can be changed while 5 100000
the adjustable frequency drive is in operation, and “FALSE” 4 10000
means that the adjustable frequency drive must be 3 1000
stopped before a change can be made. 2 100
1 10
4-Set-up 0 1
'All set-ups': the parameter can be set individually in each -1 0.1
of the four set-ups, i.e., one single parameter can have four
-2 0.01
different data values.
-3 0.001
’1 set-up’: the data value will be the same in all set-ups.
-4 0.0001
-5 0.00001
Data Description Type
-6 0.000001
type
-7 0.0000001
2 Integer 8 Int8
3 Integer 16 Int16 Table 4.1 Conversion table
4 Integer 32 Int32
5 Unsigned 8 Uint8
6 Unsigned 16 Uint16
7 Unsigned 32 Uint32
9 Visible String VisStr
33 Normalized value 2 bytes N2
35 Bit sequence of 16 boolean variables V2
54 Time difference w/o date TimD

4.1.1 Conversion

The various attributes of each parameter are displayed in

the section Factory Settings. Parameter values are
transferred as whole numbers only. Conversion factors are
therefore used to transfer decimals.

4-12 Motor Speed Low Limit [Hz] has a conversion factor of

0.1.
To preset the minimum frequency to 10 Hz, transfer the
value 100. A conversion factor of 0.1 means that the value
transferred is multiplied by 0.1. The value 100 is thus
perceived as 10.0.

Examples:
0s --> conversion index 0
0.00s --> conversion index -2
0ms --> conversion index -3
0.00ms --> conversion index -5

MG33MD22 - VLT® is a registered Danfoss trademark 4-1

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

4.1.2 Active/Inactive Parameters in Different Drive Control Modes

+ = active
- = not active

1-10 Motor Construction AC motor PM Non-salient Motor

4 4
1-01 Motor Control Principle Flux Flux
Flux open- Flux closed-
U/f mode VVC+ U/f mode open- closed-
loop loop
loop loop
1-00 Configuration Mode
[0] Speed Open-loop + + + -
[1] Speed Closed-loop - + - +
[2] Torque - - - +
[3] Process + + + -
[4] Torque Open-loop - + - -
[5] Wobble + + + +
[6] Surface Winder + + + -
[7] Ext. PID Open-loop + + + -
[8] Ext. PID Closed-loop - + - +

1-02 Flux Motor Feedback Source - - - +

1-03 Torque Characteristics + + +
-
see 1, 2, 3) see 1, 3, 4) see 1, 3, 4)
1-04 Overload Mode + + + + + + +
1-05 Local Mode Configuration + + + + + + +
1-06 Clockwise Direction + + + + + + +
1-20 Motor Power [kW]
+ + + +
(Par. 023 = International)
1-21 Motor Power [HP]
+ + + +
(Par. 023 = US)
1-22 Motor Voltage + + + +
1-23 Motor Frequency + + + +
1-24 Motor Current + + + +
1-25 Motor Nominal Speed + + + +
1-26 Motor Cont. Rated Torque - - - - + + +
1-29 Automatic Motor Adaptation (AMA) + + + +
1-30 Stator Resistance (Rs) + + + + +
1-31 Rotor Resistance (Rr) +
- + +
see 5)
1-33 Stator Leakage Reactance (X1) + + + + +
1-34 Rotor Leakage Reactance (X2) +
- + +
see 5)
1-35 Main Reactance (Xh) + + + + +
1-36 Iron Loss Resistance (Rfe) - - + + - - -
1-37 d-axis Inductance (Ld) - - - - + +
1-39 Motor Poles + + + +
1-40 Back EMF at 1000 RPM - - - - + + +
1-41 Motor Angle Offset - - - - +

1) Constant torque 5) Used in flystart

2) Variable torque
3) AEO
4) Constant power

4-2 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

1-10 Motor Construction AC motor PM Non-salient Motor

1-01 Motor Control Principle Flux
Flux closed- Flux
U/f mode VVC+ Flux open-loop U/f mode closed-
loop open-loop
loop
1-50 Motor Magnetisation at Zero
- + - - - - -
Speed
1-51 Min Speed Normal
Magnetising [RPM](Par. 002 = rmp)
- + - - - - -
4 4
1-52 Min Speed Normal Magnetising
- + - - - - -
[Hz](Par. 002 = Hz)
1-53 Model Shift Frequency - - + + - + +
1-54 Voltage reduction in +
- - + - - -
fieldweakening see 6)
1-55 U/f Characteristic - U + - - - + - -
1-56 U/f Characteristic - F + - - - + - -
1-58 Flystart Test Pulses Current - + - - - - -
1-59 Flystart Test Pulses Frequency - + - - - - -
1-60 Low Speed Load Compensation - + - - - - -
1-61 High Speed Load Compen-
- + - - - - -
sation
1-62 Slip Compensation +
- + - - - -
see 7)
1-63 Slip Compensation Time + + + +
+ - -
Constant see 8) see 8) see 8) see 8)
1-64 Resonance Dampening + + + - + + -
1-65 Resonance Dampening Time
+ + + - + + -
Constant
1-66 Min. Current at Low Speed - - + + - + +
1-67 Load Type - - + - - - -
1-68 Minimum Inertia - - + - - - -
1-69 Maximum Inertia - - + - - - -
1-71 Start Delay + + + + + + +
1-72 Start Function + + + + + + +
1-73 Flying Start - + + + - - -
1-74 Start Speed [RPM](Par. 002 =
- + - - - - -
rmp)
1-75 Start Speed [Hz](Par. 002 = Hz) - + - - - - -
1-76 Start Current - + - - - - -

6) Used when 1-03 Torque Characteristics is constant power

7) Not used when 1-03 Torque Characteristics = VT
8) Part of resonance damping

MG33MD22 - VLT® is a registered Danfoss trademark 4-3

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

1-10 Motor Construction AC motor PM Non-salient Motor

1-01 Motor Control Principle Flux open- Flux closed- Flux open- Flux
U/f mode VVC+ U/f mode
loop loop loop closed-loop
1-80 Function at Stop + + + + + + +
1-81 Min Speed for Function at
Stop [RPM] + + + + + + +
(Par. 002 = rpm)
4 4 1-82 Min Speed for Function at
Stop [Hz] + + + + + + +
(Par. 002 = Hz)
1-83 Precise Stop Function + + + + + + +
1-84 Precise Stop Counter Value + + + + + + +
1-85 Precise Stop Speed Compen-
+ + + + + + +
sation Delay
1-90 Motor Thermal Protection + + + +
1-91 Motor External Fan + + + +
1-93 Thermistor Resource + + + +
1-95 KTY Sensor Type + + + +
1-96 KTY Thermistor Resource + + + +
1-97 KTY Threshold level + + + +
1-98 ATEX ETR interpol. points freq. + + + +
1-99 ATEX ETR interpol points current + + + +
2-00 DC Hold Current + + + +
2-01 DC Brake Current + + + +
2-02 DC Braking Time + + + +
2-03 DC Brake Cut In Speed [RPM] + + + +
2-04 DC Brake Cut In Speed [Hz] + + + +
2-05 Maximum Reference + + + +
2-10 Brake Function +
+ + +
see 9)
2-11 Brake Resistor (ohm) + + + +
2-12 Brake Power Limit (kW) + + + +
2-13 Brake Power Monitoring + + + +
2-15 Brake Check +
+ + +
see 9)
2-16 AC brake Max. Current - + + +
2-17 Over-voltage Control + + + +
2-18 Brake Check Condition + + + +
2-19 Over-voltage Gain + + + -
2-20 Release Brake Current + + + +
2-21 Activate Brake Speed [RPM] + + + +
2-22 Activate Brake Speed [Hz] + + + +
2-23 Activate Brake Delay + + + +
2-24 Stop Delay - - - +
2-25 Brake Release Time - - - +
2-26 Torque Ref - - - +
2-27 Torque Ramp Time - - - +
2-28 Gain Boost Factor - - - +

9) Not AC brake

4-4 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

4.1.3 0-** Operation/Display

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
0-0* Basic Settings
0-01 Language [0] English 1 set-up TRUE - Uint8
0-02 Motor Speed Unit [0] RPM 2 set-ups FALSE - Uint8 4 4
0-03 Regional Settings [0] International 2 set-ups FALSE - Uint8
0-04 Operating State at Power-up (Hand) [1] Forced stop, ref=old All set-ups TRUE - Uint8
0-09 Performance Monitor 0.0 % All set-ups TRUE -1 Uint16
0-1* Set-up Operations
0-10 Active Set-up [1] Set-up 1 1 set-up TRUE - Uint8
0-11 Edit Set-up [1] Set-up 1 All set-ups TRUE - Uint8
0-12 This Set-up Linked to [0] Not linked All set-ups FALSE - Uint8
0-13 Readout: Linked Set-ups 0 N/A All set-ups FALSE 0 Uint16
0-14 Readout: Edit Set-ups / Channel 0 N/A All set-ups TRUE 0 Int32
0-15 Readout: actual setup 0 N/A All set-ups FALSE 0 Uint8
0-2* LCP Display
0-20 Display Line 1.1 Small 1617 All set-ups TRUE - Uint16
0-21 Display Line 1.2 Small 1614 All set-ups TRUE - Uint16
0-22 Display Line 1.3 Small 1610 All set-ups TRUE - Uint16
0-23 Display Line 2 Large 1613 All set-ups TRUE - Uint16
0-24 Display Line 3 Large 1602 All set-ups TRUE - Uint16
0-25 My Personal Menu ExpressionLimit 1 set-up TRUE 0 Uint16
0-3* LCP Cust. Readout
0-30 Unit for User-defined Readout [0] None All set-ups TRUE - Uint8
0-31 Min Value of User-defined Readout 0.00 CustomReadoutUnit All set-ups TRUE -2 Int32
100.00 CustomRea-
0-32 Max Value of User-defined Readout doutUnit All set-ups TRUE -2 Int32
0-37 Display Text 1 0 N/A 1 set-up TRUE 0 VisStr[25]
0-38 Display Text 2 0 N/A 1 set-up TRUE 0 VisStr[25]
0-39 Display Text 3 0 N/A 1 set-up TRUE 0 VisStr[25]
0-4* LCP Keypad
0-40 [Hand on] Key on LCP null All set-ups TRUE - Uint8
0-41 [Off] Key on LCP null All set-ups TRUE - Uint8
0-42 [Auto on] Key on LCP null All set-ups TRUE - Uint8
0-43 [Reset] Key on LCP null All set-ups TRUE - Uint8
0-44 [Off/Reset] Key on LCP null All set-ups TRUE - Uint8
0-45 [Drive Bypass] Key on LCP null All set-ups TRUE - Uint8
0-5* Copy/Save
0-50 LCP Copy [0] No copy All set-ups FALSE - Uint8
0-51 Set-up Copy [0] No copy All set-ups FALSE - Uint8
0-6* Password
0-60 Main Menu Password 100 N/A 1 set-up TRUE 0 Int16
0-61 Access to Main Menu w/o Password [0] Full access 1 set-up TRUE - Uint8
0-65 Quick Menu Password 200 N/A 1 set-up TRUE 0 Int16
0-66 Access to Quick Menu w/o Password [0] Full access 1 set-up TRUE - Uint8
0-67 Bus Password Access 0 N/A All set-ups TRUE 0 Uint16

MG33MD22 - VLT® is a registered Danfoss trademark 4-5

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

4.1.4 1-** Load/Motor

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
1-0* General Settings
1-00 Configuration Mode null All set-ups TRUE - Uint8
4 4 1-01 Motor Control Principle null All set-ups FALSE - Uint8
1-02 Flux Motor Feedback Source [1] 24V encoder All set-ups x FALSE - Uint8
1-03 Torque Characteristics [0] Constant torque All set-ups TRUE - Uint8
1-04 Overload Mode [0] High torque All set-ups FALSE - Uint8
1-05 Local Mode Configuration [2] As mode par 1-00 All set-ups TRUE - Uint8
1-06 Clockwise Direction [0] Normal All set-ups FALSE - Uint8
1-1* Motor Selection
1-10 Motor Construction [0] Asynchron All set-ups FALSE - Uint8
1-2* Motor Data
1-20 Motor Power [kW] ExpressionLimit All set-ups FALSE 1 Uint32
1-21 Motor Power [HP] ExpressionLimit All set-ups FALSE -2 Uint32
1-22 Motor Voltage ExpressionLimit All set-ups FALSE 0 Uint16
1-23 Motor Frequency ExpressionLimit All set-ups FALSE 0 Uint16
1-24 Motor Current ExpressionLimit All set-ups FALSE -2 Uint32
1-25 Motor Nominal Speed ExpressionLimit All set-ups FALSE 67 Uint16
1-26 Motor Cont. Rated Torque ExpressionLimit All set-ups FALSE -1 Uint32
1-29 Automatic Motor Adaptation (AMA) [0] Off All set-ups FALSE - Uint8
1-3* Addl. Motor Data
1-30 Stator Resistance (Rs) ExpressionLimit All set-ups FALSE -4 Uint32
1-31 Rotor Resistance (Rr) ExpressionLimit All set-ups FALSE -4 Uint32
1-33 Stator Leakage Reactance (X1) ExpressionLimit All set-ups FALSE -4 Uint32
1-34 Rotor Leakage Reactance (X2) ExpressionLimit All set-ups FALSE -4 Uint32
1-35 Main Reactance (Xh) ExpressionLimit All set-ups FALSE -4 Uint32
1-36 Iron Loss Resistance (Rfe) ExpressionLimit All set-ups FALSE -3 Uint32
1-37 d-axis Inductance (Ld) ExpressionLimit All set-ups x FALSE -4 Int32
1-39 Motor Poles ExpressionLimit All set-ups FALSE 0 Uint8
1-40 Back EMF at 1000 RPM ExpressionLimit All set-ups x FALSE 0 Uint16
1-41 Motor Angle Offset 0 N/A All set-ups FALSE 0 Int16
1-5* Load-Indep. Setting
1-50 Motor Magnetization at Zero Speed 100 % All set-ups TRUE 0 Uint16
1-51 Min Speed Normal Magnetizing [RPM] ExpressionLimit All set-ups TRUE 67 Uint16
1-52 Min Speed Normal Magnetizing [Hz] ExpressionLimit All set-ups TRUE -1 Uint16
1-53 Model Shift Frequency ExpressionLimit All set-ups x FALSE -1 Uint16
1-54 Voltage reduction in fieldweakening 0V All set-ups FALSE 0 Uint8
1-55 U/f Characteristic - U ExpressionLimit All set-ups TRUE -1 Uint16
1-56 U/f Characteristic - F ExpressionLimit All set-ups TRUE -1 Uint16
1-58 Flystart Test Pulses Current 30 % All set-ups FALSE 0 Uint16
1-59 Flystart Test Pulses Frequency 200 % All set-ups FALSE 0 Uint16
1-6* Load-Depend. Settg.
1-60 Low Speed Load Compensation 100 % All set-ups TRUE 0 Int16
1-61 High Speed Load Compensation 100 % All set-ups TRUE 0 Int16
1-62 Slip Compensation ExpressionLimit All set-ups TRUE 0 Int16
1-63 Slip Compensation Time Constant ExpressionLimit All set-ups TRUE -2 Uint16
1-64 Resonance Dampening 100 % All set-ups TRUE 0 Uint16

4-6 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
1-65 Resonance Dampening Time Constant 5 ms All set-ups TRUE -3 Uint8
1-66 Min. Current at Low Speed 100 % All set-ups x TRUE 0 Uint32
1-67 Load Type [0] Passive load All set-ups x TRUE - Uint8
1-68 Minimum Inertia ExpressionLimit All set-ups x FALSE -4 Uint32
1-69 Maximum Inertia ExpressionLimit All set-ups x FALSE -4 Uint32 4 4
1-7* Start Adjustments
1-71 Start Delay 0.0 s All set-ups TRUE -1 Uint8
1-72 Start Function [2] Coast/delay time All set-ups TRUE - Uint8
1-73 Flying Start null All set-ups FALSE - Uint8
1-74 Start Speed [RPM] ExpressionLimit All set-ups TRUE 67 Uint16
1-75 Start Speed [Hz] ExpressionLimit All set-ups TRUE -1 Uint16
1-76 Start Current 0.00 A All set-ups TRUE -2 Uint32
1-8* Stop Adjustments
1-80 Function at Stop [0] Coast All set-ups TRUE - Uint8
1-81 Min Speed for Function at Stop [RPM] ExpressionLimit All set-ups TRUE 67 Uint16
1-82 Min Speed for Function at Stop [Hz] ExpressionLimit All set-ups TRUE -1 Uint16
1-83 Precise Stop Function [0] Precise ramp stop All set-ups FALSE - Uint8
1-84 Precise Stop Counter Value 100000 N/A All set-ups TRUE 0 Uint32
1-85 Precise Stop Speed Compensation Delay 10 ms All set-ups TRUE -3 Uint8
1-9* Motor Temperature
1-90 Motor Thermal Protection [0] No protection All set-ups TRUE - Uint8
1-91 Motor External Fan [0] No All set-ups TRUE - Uint16
1-93 Thermistor Resource [0] None All set-ups TRUE - Uint8
1-94 ATEX ETR cur.lim. speed reduction 0.0 % 2 set-ups x TRUE -1 Uint16
1-95 KTY Sensor Type [0] KTY Sensor 1 All set-ups x TRUE - Uint8
1-96 KTY Thermistor Resource [0] None All set-ups x TRUE - Uint8
1-97 KTY Threshold level 80 °C 1 set-up x TRUE 100 Int16
1-98 ATEX ETR interpol. points freq. ExpressionLimit 1 set-up x TRUE -1 Uint16
1-99 ATEX ETR interpol points current ExpressionLimit 2 set-ups x TRUE 0 Uint16

MG33MD22 - VLT® is a registered Danfoss trademark 4-7

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

4.1.5 2-** Brakes

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
2-0* DC Brake
2-00 DC Hold Current 50 % All set-ups TRUE 0 Uint8
4 4 2-01 DC Brake Current 50 % All set-ups TRUE 0 Uint16
2-02 DC Braking Time 10.0 s All set-ups TRUE -1 Uint16
2-03 DC Brake Cut-in Speed [RPM] ExpressionLimit All set-ups TRUE 67 Uint16
2-04 DC Brake Cut-in Speed [Hz] ExpressionLimit All set-ups TRUE -1 Uint16
2-05 Maximum Reference MaxReference (P303) All set-ups TRUE -3 Int32
2-1* Brake Energy Funct.
2-10 Brake Function null All set-ups TRUE - Uint8
2-11 Brake Resistor (ohm) ExpressionLimit All set-ups TRUE 0 Uint16
2-12 Brake Power Limit (kW) ExpressionLimit All set-ups TRUE 0 Uint32
2-13 Brake Power Monitoring [0] Off All set-ups TRUE - Uint8
2-15 Brake Check [0] Off All set-ups TRUE - Uint8
2-16 AC brake Max. Current 100.0 % All set-ups TRUE -1 Uint32
2-17 Over-voltage Control [0] Disabled All set-ups TRUE - Uint8
2-18 Brake Check Condition [0] At Power-up All set-ups TRUE - Uint8
2-19 Over-voltage Gain 100 % All set-ups TRUE 0 Uint16
2-2* Mechanical Brake
2-20 Release Brake Current ImaxVLT (P1637) All set-ups TRUE -2 Uint32
2-21 Activate Brake Speed [RPM] ExpressionLimit All set-ups TRUE 67 Uint16
2-22 Activate Brake Speed [Hz] ExpressionLimit All set-ups TRUE -1 Uint16
2-23 Activate Brake Delay 0.0 s All set-ups TRUE -1 Uint8
2-24 Stop Delay 0.0 s All set-ups TRUE -1 Uint8
2-25 Brake Release Time 0.20 s All set-ups TRUE -2 Uint16
2-26 Torque Ref 0.00 % All set-ups TRUE -2 Int16
2-27 Torque Ramp Time 0.2 s All set-ups TRUE -1 Uint8
2-28 Gain Boost Factor 1.00 N/A All set-ups TRUE -2 Uint16

4-8 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

4.1.6 3-** Reference / Ramps

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
3-0* Reference Limits
3-00 Reference Range null All set-ups TRUE - Uint8
3-01 Reference/Feedback Unit null All set-ups TRUE - Uint8 4 4
3-02 Minimum Reference ExpressionLimit All set-ups TRUE -3 Int32
3-03 Maximum Reference ExpressionLimit All set-ups TRUE -3 Int32
3-04 Reference Function [0] Sum All set-ups TRUE - Uint8
3-1* References
3-10 Preset Reference 0.00 % All set-ups TRUE -2 Int16
3-11 Jog Speed [Hz] ExpressionLimit All set-ups TRUE -1 Uint16
3-12 Catch up/slow-down Value 0.00 % All set-ups TRUE -2 Int16
3-13 Reference Site [0] Linked to Hand / Auto All set-ups TRUE - Uint8
3-14 Preset Relative Reference 0.00 % All set-ups TRUE -2 Int32
3-15 Reference Resource 1 null All set-ups TRUE - Uint8
3-16 Reference Resource 2 null All set-ups TRUE - Uint8
3-17 Reference Resource 3 null All set-ups TRUE - Uint8
3-18 Relative Scaling Reference Resource [0] No function All set-ups TRUE - Uint8
3-19 Jog Speed [RPM] ExpressionLimit All set-ups TRUE 67 Uint16
3-4* Ramp 1
3-40 Ramp 1 Type [0] Linear All set-ups TRUE - Uint8
3-41 Ramp 1 Ramp-up Time ExpressionLimit All set-ups TRUE -2 Uint32
3-42 Ramp 1 Ramp-down Time ExpressionLimit All set-ups TRUE -2 Uint32
3-45 Ramp 1 S-ramp Ratio at Accel. Start 50 % All set-ups TRUE 0 Uint8
3-46 Ramp 1 S-ramp Ratio at Accel. End 50 % All set-ups TRUE 0 Uint8
3-47 Ramp 1 S-ramp Ratio at Decel. Start 50 % All set-ups TRUE 0 Uint8
3-48 Ramp 1 S-ramp Ratio at Decel. End 50 % All set-ups TRUE 0 Uint8
3-5* Ramp 2
3-50 Ramp 2 Type [0] Linear All set-ups TRUE - Uint8
3-51 Ramp 2 Ramp-up Time ExpressionLimit All set-ups TRUE -2 Uint32
3-52 Ramp 2 Ramp-down Time ExpressionLimit All set-ups TRUE -2 Uint32
3-55 Ramp 2 S-ramp Ratio at Accel. Start 50 % All set-ups TRUE 0 Uint8
3-56 Ramp 2 S-ramp Ratio at Accel. End 50 % All set-ups TRUE 0 Uint8
3-57 Ramp 2 S-ramp Ratio at Decel. Start 50 % All set-ups TRUE 0 Uint8
3-58 Ramp 2 S-ramp Ratio at Decel. End 50 % All set-ups TRUE 0 Uint8
3-6* Ramp 3
3-60 Ramp 3 Type [0] Linear All set-ups TRUE - Uint8
3-61 Ramp 3 Ramp-up Time ExpressionLimit All set-ups TRUE -2 Uint32
3-62 Ramp 3 Ramp-down Time ExpressionLimit All set-ups TRUE -2 Uint32
3-65 Ramp 3 S-ramp Ratio at Accel. Start 50 % All set-ups TRUE 0 Uint8
3-66 Ramp 3 S-ramp Ratio at Accel. End 50 % All set-ups TRUE 0 Uint8
3-67 Ramp 3 S-ramp Ratio at Decel. Start 50 % All set-ups TRUE 0 Uint8
3-68 Ramp 3 S-ramp Ratio at Decel. End 50 % All set-ups TRUE 0 Uint8
3-7* Ramp 4
3-70 Ramp 4 Type [0] Linear All set-ups TRUE - Uint8
3-71 Ramp 4 Ramp-up Time ExpressionLimit All set-ups TRUE -2 Uint32
3-72 Ramp 4 Ramp-down Time ExpressionLimit All set-ups TRUE -2 Uint32
3-75 Ramp 4 S-ramp Ratio at Accel. Start 50 % All set-ups TRUE 0 Uint8

MG33MD22 - VLT® is a registered Danfoss trademark 4-9

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
3-76 Ramp 4 S-ramp Ratio at Accel. End 50 % All set-ups TRUE 0 Uint8
3-77 Ramp 4 S-ramp Ratio at Decel. Start 50 % All set-ups TRUE 0 Uint8
3-78 Ramp 4 S-ramp Ratio at Decel. End 50 % All set-ups TRUE 0 Uint8
3-8* Other Ramps
4 4 3-80 Jog Ramp Time ExpressionLimit All set-ups TRUE -2 Uint32
3-81 Quick Stop Ramp Time ExpressionLimit 2 set-ups TRUE -2 Uint32
3-82 Quick Stop Ramp Type [0] Linear All set-ups TRUE - Uint8
3-83 Quick Stop S-ramp Ratio at Decel. Start 50 % All set-ups TRUE 0 Uint8
3-84 Quick Stop S-ramp Ratio at Decel. End 50 % All set-ups TRUE 0 Uint8
3-9* Digital Pot. meter
3-90 Step Size 0.10 % All set-ups TRUE -2 Uint16
3-91 Ramp Time 1.00 s All set-ups TRUE -2 Uint32
3-92 Power Restore [0] Off All set-ups TRUE - Uint8
3-93 Maximum Limit 100 % All set-ups TRUE 0 Int16
3-94 Minimum Limit -100 % All set-ups TRUE 0 Int16
3-95 Ramp Delay ExpressionLimit All set-ups TRUE -3 TimD

4-10 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

4.1.7 4-** Limits / Warnings

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
4-1* Motor Limits
4-10 Motor Speed Direction null All set-ups FALSE - Uint8
4-11 Motor Speed Low Limit [RPM] ExpressionLimit All set-ups TRUE 67 Uint16 4 4
4-12 Motor Speed Low Limit [Hz] ExpressionLimit All set-ups TRUE -1 Uint16
4-13 Motor Speed High Limit [RPM] ExpressionLimit All set-ups TRUE 67 Uint16
4-14 Motor Speed High Limit [Hz] ExpressionLimit All set-ups TRUE -1 Uint16
4-16 Torque Limit Motor Mode ExpressionLimit All set-ups TRUE -1 Uint16
4-17 Torque Limit Generator Mode 100.0 % All set-ups TRUE -1 Uint16
4-18 Current Limit ExpressionLimit All set-ups TRUE -1 Uint32
4-19 Max Output Frequency 132.0 Hz All set-ups FALSE -1 Uint16
4-2* Limit Factors
4-20 Torque Limit Factor Source [0] No function All set-ups TRUE - Uint8
4-21 Speed Limit Factor Source [0] No function All set-ups TRUE - Uint8
4-3* Motor Speed Mon.
4-30 Motor Feedback Loss Function [2] Trip All set-ups TRUE - Uint8
4-31 Motor Feedback Speed Error 300 RPM All set-ups TRUE 67 Uint16
4-32 Motor Feedback Loss Timeout 0.05 s All set-ups TRUE -2 Uint16
4-34 Tracking Error Function null All set-ups TRUE - Uint8
4-35 Tracking Error 10 RPM All set-ups TRUE 67 Uint16
4-36 Tracking Error Timeout 1.00 s All set-ups TRUE -2 Uint16
4-37 Tracking Error Ramping 100 RPM All set-ups TRUE 67 Uint16
4-38 Tracking Error Ramping Timeout 1.00 s All set-ups TRUE -2 Uint16
4-39 Tracking Error After Ramping Timeout 5.00 s All set-ups TRUE -2 Uint16
4-5* Adj. Warnings
4-50 Warning Current Low 0.00 A All set-ups TRUE -2 Uint32
4-51 Warning Current High ImaxVLT (P1637) All set-ups TRUE -2 Uint32
4-52 Warning Speed Low 0 RPM All set-ups TRUE 67 Uint16
outputSpeedHighLimit
4-53 Warning Speed High (P413) All set-ups TRUE 67 Uint16

4-54 Warning Reference Low -999999.999 N/A All set-ups TRUE -3 Int32
4-55 Warning Reference High 999999.999 N/A All set-ups TRUE -3 Int32
-999999.999 Reference-
4-56 Warning Feedback Low FeedbackUnit All set-ups TRUE -3 Int32
999999.999 Reference-
4-57 Warning Feedback High FeedbackUnit All set-ups TRUE -3 Int32
4-58 Missing Motor Phase Function null All set-ups TRUE - Uint8
4-6* Speed Bypass
4-60 Bypass Speed From [RPM] ExpressionLimit All set-ups TRUE 67 Uint16
4-61 Bypass Speed From [Hz] ExpressionLimit All set-ups TRUE -1 Uint16
4-62 Bypass Speed to [RPM] ExpressionLimit All set-ups TRUE 67 Uint16
4-63 Bypass Speed To [Hz] ExpressionLimit All set-ups TRUE -1 Uint16

MG33MD22 - VLT® is a registered Danfoss trademark 4-11

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

4.1.8 5-** Digital In/Out

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
5-0* Digital I/O mode
5-00 Digital I/O Mode [0] PNP All set-ups FALSE - Uint8
4 4 5-01 Terminal 27 Mode [0] Input All set-ups TRUE - Uint8
5-02 Terminal 29 Mode [0] Input All set-ups x TRUE - Uint8
5-1* Digital Inputs
5-10 Terminal 18 Digital Input null All set-ups TRUE - Uint8
5-11 Terminal 19 Digital Input null All set-ups TRUE - Uint8
5-12 Terminal 27 Digital Input null All set-ups TRUE - Uint8
5-13 Terminal 29 Digital Input null All set-ups x TRUE - Uint8
5-14 Terminal 32 Digital Input null All set-ups TRUE - Uint8
5-15 Terminal 33 Digital Input null All set-ups TRUE - Uint8
5-16 Terminal X30/2 Digital Input null All set-ups TRUE - Uint8
5-17 Terminal X30/3 Digital Input null All set-ups TRUE - Uint8
5-18 Terminal X30/4 Digital Input null All set-ups TRUE - Uint8
5-19 Terminal 37 Safe Stop null 1 set-up TRUE - Uint8
5-20 Terminal X46/1 Digital Input [0] No operation All set-ups TRUE - Uint8
5-21 Terminal X46/3 Digital Input [0] No operation All set-ups TRUE - Uint8
5-22 Terminal X46/5 Digital Input [0] No operation All set-ups TRUE - Uint8
5-23 Terminal X46/7 Digital Input [0] No operation All set-ups TRUE - Uint8
5-24 Terminal X46/9 Digital Input [0] No operation All set-ups TRUE - Uint8
5-25 Terminal X46/11 Digital Input [0] No operation All set-ups TRUE - Uint8
5-26 Terminal X46/13 Digital Input [0] No operation All set-ups TRUE - Uint8
5-3* Digital Outputs
5-30 Terminal 27 Digital Output null All set-ups TRUE - Uint8
5-31 Terminal 29 digital Output null All set-ups x TRUE - Uint8
5-32 Term X30/6 Digi Out (MCB 101) null All set-ups TRUE - Uint8
5-33 Term X30/7 Digi Out (MCB 101) null All set-ups TRUE - Uint8
5-4* Relays
5-40 Function Relay null All set-ups TRUE - Uint8
5-41 On Delay, Relay 0.01 s All set-ups TRUE -2 Uint16
5-42 Off Delay, Relay 0.01 s All set-ups TRUE -2 Uint16
5-5* Pulse Input
5-50 Term. 29 Low Frequency 100 Hz All set-ups x TRUE 0 Uint32
5-51 Term. 29 High Frequency 100 Hz All set-ups x TRUE 0 Uint32
0.000 ReferenceFeed-
5-52 Term. 29 Low Ref./Feedb. Value backUnit All set-ups x TRUE -3 Int32
5-53 Term. 29 High Ref./Feedb. Value ExpressionLimit All set-ups x TRUE -3 Int32
5-54 Pulse Filter Time Constant #29 100 ms All set-ups x FALSE -3 Uint16
5-55 Term. 33 Low Frequency 100 Hz All set-ups TRUE 0 Uint32
5-56 Term. 33 High Frequency 100 Hz All set-ups TRUE 0 Uint32
0.000 ReferenceFeed-
5-57 Term. 33 Low Ref./Feedb. Value backUnit All set-ups TRUE -3 Int32
5-58 Term. 33 High Ref./Feedb. Value ExpressionLimit All set-ups TRUE -3 Int32
5-59 Pulse Filter Time Constant #33 100 ms All set-ups FALSE -3 Uint16
5-6* Pulse Output
5-60 Terminal 27 Pulse Output Variable null All set-ups TRUE - Uint8

4-12 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
5-62 Pulse Output Max Freq #27 ExpressionLimit All set-ups TRUE 0 Uint32
5-63 Terminal 29 Pulse Output Variable null All set-ups x TRUE - Uint8
5-65 Pulse Output Max Freq #29 ExpressionLimit All set-ups x TRUE 0 Uint32
5-66 Terminal X30/6 Pulse Output Variable null All set-ups TRUE - Uint8
5-68 Pulse Output Max Freq #X30/6 ExpressionLimit All set-ups TRUE 0 Uint32 4 4
5-7* 24V Encoder Input
5-70 Term 32/33 Pulses per Revolution 1024 N/A All set-ups FALSE 0 Uint16
5-71 Term 32/33 Encoder Direction [0] Clockwise All set-ups FALSE - Uint8
5-8* I/O Options
5-80 AHF Cap Reconnect Delay 25 s 2 set-ups x TRUE 0 Uint16
5-9* Bus Controlled
5-90 Digital & Relay Bus Control 0 N/A All set-ups TRUE 0 Uint32
5-93 Pulse Out #27 Bus Control 0.00 % All set-ups TRUE -2 N2
5-94 Pulse Out #27 Timeout Preset 0.00 % 1 set-up TRUE -2 Uint16
5-95 Pulse Out #29 Bus Control 0.00 % All set-ups x TRUE -2 N2
5-96 Pulse Out #29 Timeout Preset 0.00 % 1 set-up x TRUE -2 Uint16
5-97 Pulse Out #X30/6 Bus Control 0.00 % All set-ups TRUE -2 N2
5-98 Pulse Out #X30/6 Timeout Preset 0.00 % 1 set-up TRUE -2 Uint16

MG33MD22 - VLT® is a registered Danfoss trademark 4-13

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

4.1.9 6-** Analog In/Out

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
6-0* Analog I/O Mode
6-00 Live Zero Timeout Time 10 s All set-ups TRUE 0 Uint8
4 4 6-01 Live Zero Timeout Function [0] Off All set-ups TRUE - Uint8
6-1* Analog Input 1
6-10 Terminal 53 Low Voltage 0.07 V All set-ups TRUE -2 Int16
6-11 Terminal 53 High Voltage 10.00 V All set-ups TRUE -2 Int16
6-12 Terminal 53 Low Current 0.14 mA All set-ups TRUE -5 Int16
6-13 Terminal 53 High Current 20.00 mA All set-ups TRUE -5 Int16
6-14 Terminal 53 Low Ref./Feedb. Value 0 ReferenceFeedbackUnit All set-ups TRUE -3 Int32
6-15 Terminal 53 High Ref./Feedb. Value ExpressionLimit All set-ups TRUE -3 Int32
6-16 Terminal 53 Filter Time Constant 0.001 s All set-ups TRUE -3 Uint16
6-2* Analog Input 2
6-20 Terminal 54 Low Voltage 0.07 V All set-ups TRUE -2 Int16
6-21 Terminal 54 High Voltage 10.00 V All set-ups TRUE -2 Int16
6-22 Terminal 54 Low Current 0.14 mA All set-ups TRUE -5 Int16
6-23 Terminal 54 High Current 20.00 mA All set-ups TRUE -5 Int16
6-24 Terminal 54 Low Ref./Feedb. Value 0 ReferenceFeedbackUnit All set-ups TRUE -3 Int32
6-25 Terminal 54 High Ref./Feedb. Value ExpressionLimit All set-ups TRUE -3 Int32
6-26 Terminal 54 Filter Time Constant 0.001 s All set-ups TRUE -3 Uint16
6-3* Analog Input 53
6-30 Terminal X30/11 Low Voltage 0.07 V All set-ups TRUE -2 Int16
6-31 Terminal X30/11 High Voltage 10.00 V All set-ups TRUE -2 Int16
6-34 Term. X30/11 Low Ref./Feedb. Value 0 ReferenceFeedbackUnit All set-ups TRUE -3 Int32
6-35 Term. X30/11 High Ref./Feedb. Value ExpressionLimit All set-ups TRUE -3 Int32
6-36 Term. X30/11 Filter Time Constant 0.001 s All set-ups TRUE -3 Uint16
6-4* Analog Input 4
6-40 Terminal X30/12 Low Voltage 0.07 V All set-ups TRUE -2 Int16
6-41 Terminal X30/12 High Voltage 10.00 V All set-ups TRUE -2 Int16
6-44 Term. X30/12 Low Ref./Feedb. Value 0 ReferenceFeedbackUnit All set-ups TRUE -3 Int32
6-45 Term. X30/12 High Ref./Feedb. Value ExpressionLimit All set-ups TRUE -3 Int32
6-46 Term. X30/12 Filter Time Constant 0.001 s All set-ups TRUE -3 Uint16
6-5* Analog Output 1
6-50 Terminal 42 Output null All set-ups TRUE - Uint8
6-51 Terminal 42 Output Min Scale 0.00 % All set-ups TRUE -2 Int16
6-52 Terminal 42 Output Max Scale 100.00 % All set-ups TRUE -2 Int16
6-53 Terminal 42 Output Bus Control 0.00 % All set-ups TRUE -2 N2
6-54 Terminal 42 Output Timeout Preset 0.00 % 1 set-up TRUE -2 Uint16
6-55 Terminal 42 Output Filter [0] Off 1 set-up TRUE - Uint8
6-6* Analog Output 2
6-60 Terminal X30/8 Output null All set-ups TRUE - Uint8
6-61 Terminal X30/8 Min. Scale 0.00 % All set-ups TRUE -2 Int16
6-62 Terminal X30/8 Max. Scale 100.00 % All set-ups TRUE -2 Int16
6-63 Terminal X30/8 Bus Control 0.00 % All set-ups TRUE -2 N2
6-64 Terminal X30/8 Output Timeout Preset 0.00 % 1 set-up TRUE -2 Uint16
6-7* Analog Output 3
6-70 Terminal X45/1 Output null All set-ups TRUE - Uint8

4-14 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
6-71 Terminal X45/1 Min. Scale 0.00 % All set-ups TRUE -2 Int16
6-72 Terminal X45/1 Max. Scale 100.00 % All set-ups TRUE -2 Int16

6-73 Terminal X45/1 Bus Control 0.00 % All set-ups TRUE -2 N2

4 4
6-74 Terminal X45/1 Output Timeout Preset 0.00 % 1 set-up TRUE -2 Uint16
6-8* Analog Output 4
6-80 Terminal X45/3 Output null All set-ups TRUE - Uint8
6-81 Terminal X45/3 Min. Scale 0.00 % All set-ups TRUE -2 Int16
6-82 Terminal X45/3 Max. Scale 100.00 % All set-ups TRUE -2 Int16
6-83 Terminal X45/3 Bus Control 0.00 % All set-ups TRUE -2 N2
6-84 Terminal X45/3 Output Timeout Preset 0.00 % 1 set-up TRUE -2 Uint16

MG33MD22 - VLT® is a registered Danfoss trademark 4-15

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

4.1.10 7-** Controllers

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
7-0* Speed PID Ctrl.
7-00 Speed PID Feedback Source null All set-ups FALSE - Uint8
4 4 7-02 Speed PID Proportional Gain ExpressionLimit All set-ups TRUE -3 Uint16
7-03 Speed PID Integral Time ExpressionLimit All set-ups TRUE -4 Uint32
7-04 Speed PID Differentiation Time ExpressionLimit All set-ups TRUE -4 Uint16
7-05 Speed PID Diff. Gain Limit 5.0 N/A All set-ups TRUE -1 Uint16
7-06 Speed PID Lowpass Filter Time ExpressionLimit All set-ups TRUE -4 Uint16
7-07 Speed PID Feedback Gear Ratio 1.0000 N/A All set-ups FALSE -4 Uint32
7-08 Speed PID Feed Forward Factor 0% All set-ups FALSE 0 Uint16
7-09 Speed PID Error Correction w/ Ramp 300 RPM All set-ups TRUE 67 Uint32
7-1* Torque PI Ctrl.
7-12 Torque PI Proportional Gain 100 % All set-ups TRUE 0 Uint16
7-13 Torque PI Integration Time 0.020 s All set-ups TRUE -3 Uint16
7-2* Process Ctrl. Feedb
7-20 Process CL Feedback 1 Resource [0] No function All set-ups TRUE - Uint8
7-22 Process CL Feedback 2 Resource [0] No function All set-ups TRUE - Uint8
7-3* Process PID Ctrl.
7-30 Process PID Normal/Inverse Control [0] Normal All set-ups TRUE - Uint8
7-31 Process PID Anti Windup [1] On All set-ups TRUE - Uint8
7-32 Process PID Controller Start Value 0 RPM All set-ups TRUE 67 Uint16
7-33 Process PID Proportional Gain 0.01 N/A All set-ups TRUE -2 Uint16
7-34 Process PID Integral Time 10000.00 s All set-ups TRUE -2 Uint32
7-35 Process PID Differentiation Time 0.00 s All set-ups TRUE -2 Uint16
7-36 Process PID Differentiation Gain Limit 5.0 N/A All set-ups TRUE -1 Uint16
7-38 Process PID Feed Forward Factor 0% All set-ups TRUE 0 Uint16
7-39 On Reference Bandwidth 5% All set-ups TRUE 0 Uint8
7-4* Adv. Process PID I
7-40 Process PID I-part Reset [0] No All set-ups TRUE - Uint8
7-41 Process PID Output Neg. Clamp -100 % All set-ups TRUE 0 Int16
7-42 Process PID Output Pos. Clamp 100 % All set-ups TRUE 0 Int16
7-43 Process PID Gain Scale at Min. Ref. 100 % All set-ups TRUE 0 Int16
7-44 Process PID Gain Scale at Max. Ref. 100 % All set-ups TRUE 0 Int16
7-45 Process PID Feed Fwd Resource [0] No function All set-ups TRUE - Uint8
7-46 Process PID Feed Fwd Normal/ Inv. Ctrl. [0] Normal All set-ups TRUE - Uint8
7-48 PCD Feed Forward 0 N/A All set-ups x TRUE 0 Uint16
7-49 Process PID Output Normal/ Inv. Ctrl. [0] Normal All set-ups TRUE - Uint8
7-5* Adv. Process PID II
7-50 Process PID Extended PID [1] Enabled All set-ups TRUE - Uint8
7-51 Process PID Feed Fwd Gain 1.00 N/A All set-ups TRUE -2 Uint16
7-52 Process PID Feed Fwd Ramp-up 0.01 s All set-ups TRUE -2 Uint32
7-53 Process PID Feed Fwd Ramp-down 0.01 s All set-ups TRUE -2 Uint32
7-56 Process PID Ref. Filter Time 0.001 s All set-ups TRUE -3 Uint16
7-57 Process PID Fb. Filter Time 0.001 s All set-ups TRUE -3 Uint16

4-16 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

4.1.11 8-** Comm. and Options

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
8-0* General Settings
8-01 Control Site [0] Digital and ctrl. word All set-ups TRUE - Uint8
8-02 Control Word Source null All set-ups TRUE - Uint8 4 4
8-03 Control Word Timeout Time 1.0 s 1 set-up TRUE -1 Uint32
8-04 Control Word Timeout Function null 1 set-up TRUE - Uint8
8-05 End-of-Timeout Function [1] Resume set-up 1 set-up TRUE - Uint8
8-06 Reset Control Word Timeout [0] Do not reset All set-ups TRUE - Uint8
8-07 Diagnosis Trigger [0] Disable 2 set-ups TRUE - Uint8
8-08 Readout Filtering null All set-ups TRUE - Uint8
8-1* Ctrl. Word Settings
8-10 Control Word Profile [0] FC profile All set-ups TRUE - Uint8
8-13 Configurable Status Word STW null All set-ups TRUE - Uint8
8-14 Configurable Control Word CTW [1] Profile default All set-ups TRUE - Uint8
8-3* FC Port Settings
8-30 Protocol [0] FC 1 set-up TRUE - Uint8
8-31 Address 1 N/A 1 set-up TRUE 0 Uint8
8-32 FC Port Baud Rate null 1 set-up TRUE - Uint8
8-33 Parity / Stop Bits [0] Ev. Par. 1 Stop Bit 1 set-up TRUE - Uint8
8-34 Estimated cycle time 0 ms 2 set-ups TRUE -3 Uint32
8-35 Minimum Response Delay 10 ms All set-ups TRUE -3 Uint16
8-36 Max Response Delay ExpressionLimit 1 set-up TRUE -3 Uint16
8-37 Max Inter-Char Delay ExpressionLimit 1 set-up TRUE -5 Uint16
8-4* FC MC protocol set
8-40 Telegram selection [1] Standard telegram 1 2 set-ups TRUE - Uint8
8-41 Parameters for signals 0 All set-ups FALSE - Uint16
8-42 PCD write configuration ExpressionLimit All set-ups TRUE 0 Uint16
8-43 PCD read configuration ExpressionLimit All set-ups TRUE 0 Uint16
8-5* Digital/Bus
8-50 Coasting Select [3] Logic OR All set-ups TRUE - Uint8
8-51 Quick Stop Select [3] Logic OR All set-ups TRUE - Uint8
8-52 DC Brake Select [3] Logic OR All set-ups TRUE - Uint8
8-53 Start Select [3] Logic OR All set-ups TRUE - Uint8
8-54 Reverse Select [3] Logic OR All set-ups TRUE - Uint8
8-55 Set-up Select [3] Logic OR All set-ups TRUE - Uint8
8-56 Preset Reference Select [3] Logic OR All set-ups TRUE - Uint8
8-57 Profidrive OFF2 Select [3] Logic OR All set-ups TRUE - Uint8
8-58 Profidrive OFF3 Select [3] Logic OR All set-ups TRUE - Uint8
8-8* AFD Port Diagnostics
8-80 Bus Message Count 0 N/A All set-ups TRUE 0 Uint32
8-81 Bus Error Count 0 N/A All set-ups TRUE 0 Uint32
8-82 Slave Messages Rcvd 0 N/A All set-ups TRUE 0 Uint32
8-83 Slave Error Count 0 N/A All set-ups TRUE 0 Uint32
8-9* Bus Jog
8-90 Bus Jog 1 Speed 100 RPM All set-ups TRUE 67 Uint16
8-91 Bus Jog 2 Speed ExpressionLimit All set-ups TRUE 67 Uint16

MG33MD22 - VLT® is a registered Danfoss trademark 4-17

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

4.1.12 9-** Profibus

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
9-00 Setpoint 0 N/A All set-ups TRUE 0 Uint16
9-07 Actual Value 0 N/A All set-ups FALSE 0 Uint16
4 4 9-15 PCD Write Configuration ExpressionLimit 1 set-up TRUE - Uint16
9-16 PCD Read Configuration ExpressionLimit 2 set-ups TRUE - Uint16
9-18 Node Address 126 N/A 1 set-up TRUE 0 Uint8
9-22 Telegram Selection [100] None 1 set-up TRUE - Uint8
9-23 Parameters for Signals 0 All set-ups TRUE - Uint16
9-27 Parameter Edit [1] Enabled 2 set-ups FALSE - Uint16
9-28 Process Control [1] Enable cyclic master 2 set-ups FALSE - Uint8
9-44 Fault Message Counter 0 N/A All set-ups TRUE 0 Uint16
9-45 Fault Code 0 N/A All set-ups TRUE 0 Uint16
9-47 Fault Number 0 N/A All set-ups TRUE 0 Uint16
9-52 Fault Situation Counter 0 N/A All set-ups TRUE 0 Uint16
9-53 Profibus Warning Word 0 N/A All set-ups TRUE 0 V2
9-63 Actual Baud Rate [255] No baud rate found All set-ups TRUE - Uint8
9-64 Device Identification 0 N/A All set-ups TRUE 0 Uint16
OctStr[
9-65 Profile Number 0 N/A All set-ups TRUE 0 2]
9-67 Control Word 1 0 N/A All set-ups TRUE 0 V2
9-68 Status Word 1 0 N/A All set-ups TRUE 0 V2
9-71 Profibus Save Data Values [0] Off All set-ups TRUE - Uint8
9-72 ProfibusDriveReset [0] No action 1 set-up FALSE - Uint8
9-75 DO Identification 0 N/A All set-ups TRUE 0 Uint16
9-80 Defined Parameters (1) 0 N/A All set-ups FALSE 0 Uint16
9-81 Defined Parameters (2) 0 N/A All set-ups FALSE 0 Uint16
9-82 Defined Parameters (3) 0 N/A All set-ups FALSE 0 Uint16
9-83 Defined Parameters (4) 0 N/A All set-ups FALSE 0 Uint16
9-84 Defined Parameters (5) 0 N/A All set-ups FALSE 0 Uint16
9-90 Changed Parameters (1) 0 N/A All set-ups FALSE 0 Uint16
9-91 Changed Parameters (2) 0 N/A All set-ups FALSE 0 Uint16
9-92 Changed Parameters (3) 0 N/A All set-ups FALSE 0 Uint16
9-93 Changed Parameters (4) 0 N/A All set-ups FALSE 0 Uint16
9-94 Changed parameters (5) 0 N/A All set-ups FALSE 0 Uint16
9-99 Profibus Revision Counter 0 N/A All set-ups TRUE 0 Uint16

4-18 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

4.1.13 10-** CAN Ser. Com. Bus

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
10-0* Common Settings
10-00 CAN Protocol null 2 set-ups FALSE - Uint8
10-01 Baud Rate Select null 2 set-ups TRUE - Uint8 4 4
10-02 MAC ID ExpressionLimit 2 set-ups TRUE 0 Uint8
10-05 Readout Transmit Error Counter 0 N/A All set-ups TRUE 0 Uint8
10-06 Readout Receive Error Counter 0 N/A All set-ups TRUE 0 Uint8
10-07 Readout Bus Off Counter 0 N/A All set-ups TRUE 0 Uint8
10-1* DeviceNet
10-10 Process Data Type Selection null All set-ups TRUE - Uint8
10-11 Process Data Config Write ExpressionLimit All set-ups TRUE - Uint16
10-12 Process Data Config Read ExpressionLimit All set-ups TRUE - Uint16
10-13 Warning Parameter 0 N/A All set-ups TRUE 0 Uint16
10-14 Net Reference [0] Off 2 set-ups TRUE - Uint8
10-15 Net Control [0] Off 2 set-ups TRUE - Uint8
10-2* COS Filters
10-20 COS Filter 1 0 N/A All set-ups FALSE 0 Uint16
10-21 COS Filter 2 0 N/A All set-ups FALSE 0 Uint16
10-22 COS Filter 3 0 N/A All set-ups FALSE 0 Uint16
10-23 COS Filter 4 0 N/A All set-ups FALSE 0 Uint16
10-3* Parameter Access
10-30 Array Index 0 N/A 2 set-ups TRUE 0 Uint8
10-31 Store Data Values [0] Off All set-ups TRUE - Uint8
10-32 Devicenet Revision ExpressionLimit All set-ups TRUE 0 Uint16
10-33 Store Always [0] Off 1 set-up TRUE - Uint8
10-34 DeviceNet Product Code ExpressionLimit 1 set-up TRUE 0 Uint16
10-39 Devicenet F Parameters 0 N/A All set-ups TRUE 0 Uint32
10-5* CANopen
10-50 Process Data Config Write. ExpressionLimit 2 set-ups TRUE - Uint16
10-51 Process Data Config Read. ExpressionLimit 2 set-ups TRUE - Uint16

MG33MD22 - VLT® is a registered Danfoss trademark 4-19

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

4.1.14 12-** Ethernet

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
operatio index
n
12-0* IP Settings
4 4 12-00 IP Address Assignment null 2 set-ups TRUE - Uint8
12-01 IP Address 0 N/A 1 set-up TRUE 0 OctStr[4]
12-02 Subnet Mask 0 N/A 1 set-up TRUE 0 OctStr[4]
12-03 Default Gateway 0 N/A 1 set-up TRUE 0 OctStr[4]
12-04 DHCP Server 0 N/A 2 set-ups TRUE 0 OctStr[4]
12-05 Lease Expires ExpressionLimit All set-ups TRUE 0 TimD
12-06 Name Servers 0 N/A 1 set-up TRUE 0 OctStr[4]
12-07 Domain Name 0 N/A 1 set-up TRUE 0 VisStr[48]
12-08 Host Name 0 N/A 1 set-up TRUE 0 VisStr[48]
12-09 Physical Address 0 N/A 1 set-up TRUE 0 VisStr[17]
12-1* Eth link par
12-10 Link Status [0] No Link All set-ups TRUE - Uint8
12-11 Link Duration ExpressionLimit All set-ups TRUE 0 TimD
12-12 Auto Negotiation [1] On 2 set-ups TRUE - Uint8
12-13 Link Speed [0] None 2 set-ups TRUE - Uint8
12-14 Link Duplex [1] Full Duplex 2 set-ups TRUE - Uint8
12-2* Process Data
12-20 Control Instance ExpressionLimit 1 set-up TRUE 0 Uint8
12-21 Process Data Config Write ExpressionLimit All set-ups TRUE - Uint16
12-22 Process Data Config Read ExpressionLimit All set-ups TRUE - Uint16
12-23 Process Data Config Write Size 16 N/A All set-ups TRUE 0 Uint32
12-24 Process Data Config Read Size 16 N/A All set-ups TRUE 0 Uint32
12-27 Master Address 0 N/A 2 set-ups FALSE 0 OctStr[4]
12-28 Store Data Values [0] Off All set-ups TRUE - Uint8
12-29 Store Always [0] Off 1 set-up TRUE - Uint8
12-3* EtherNet/IP
12-30 Warning Parameter 0 N/A All set-ups TRUE 0 Uint16
12-31 Net Reference [0] Off 2 set-ups TRUE - Uint8
12-32 Net Control [0] Off 2 set-ups TRUE - Uint8
12-33 CIP Revision ExpressionLimit All set-ups TRUE 0 Uint16
12-34 CIP Product Code ExpressionLimit 1 set-up TRUE 0 Uint16
12-35 EDS Parameter 0 N/A All set-ups TRUE 0 Uint32
12-37 COS Inhibit Timer 0 N/A All set-ups TRUE 0 Uint16
12-38 COS Filter 0 N/A All set-ups TRUE 0 Uint16
12-4* Modbus TCP
12-40 Status Parameter 0 N/A All set-ups TRUE 0 Uint16
12-41 Slave Message Count 0 N/A All set-ups TRUE 0 Uint32
12-42 Slave Exception Message Count 0 N/A All set-ups TRUE 0 Uint32
12-5* EtherCAT
12-50 Configured Station Alias 0 N/A 1 set-up FALSE 0 Uint16
12-51 Configured Station Address 0 N/A All set-ups TRUE 0 Uint16
12-59 EtherCAT Status 0 N/A All set-ups TRUE 0 Uint32
12-8* Oth. Eth. services
12-80 FTP Server [0] Disabled 2 set-ups TRUE - Uint8

4-20 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
operatio index
n
12-81 HTTP Server [0] Disabled 2 set-ups TRUE - Uint8
12-82 SMTP Service [0] Disabled 2 set-ups TRUE - Uint8
12-89 Transparent Socket Channel Port ExpressionLimit 2 set-ups TRUE 0 Uint16
12-9* Adv. Eth. services 4 4
12-90 Cable Diagnostic [0] Disabled 2 set-ups TRUE - Uint8
12-91 MDI-X [1] Enabled 2 set-ups TRUE - Uint8
12-92 IGMP Snooping [1] Enabled 2 set-ups TRUE - Uint8
12-93 Cable Error Length 0 N/A 1 set-up TRUE 0 Uint16
12-94 Broadcast Storm Protection -1 % 2 set-ups TRUE 0 Int8
12-95 Broadcast Storm Filter [0] Broadcast only 2 set-ups TRUE - Uint8
12-96 Port Config null 2 set-ups TRUE - Uint8
12-98 Interface Counters 4000 N/A All set-ups TRUE 0 Uint32
12-99 Media Counters 0 N/A All set-ups TRUE 0 Uint32

MG33MD22 - VLT® is a registered Danfoss trademark 4-21

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

4.1.15 13-** Smart Logic

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
13-0* SLC Settings
13-00 SL Controller Mode null 2 set-ups TRUE - Uint8
4 4 13-01 Start Event null 2 set-ups TRUE - Uint8
13-02 Stop Event null 2 set-ups TRUE - Uint8
13-03 Reset SLC [0] Do not reset SLC All set-ups TRUE - Uint8
13-1* Comparators
13-10 Comparator Operand null 2 set-ups TRUE - Uint8
13-11 Comparator Operator null 2 set-ups TRUE - Uint8
13-12 Comparator Value ExpressionLimit 2 set-ups TRUE -3 Int32
13-1* RS Flip Flops
13-15 RS-FF Operand S null 2 set-ups TRUE - Uint8
13-16 RS-FF Operand R null 2 set-ups TRUE - Uint8
13-2* Timers
13-20 SL Controller Timer ExpressionLimit 1 set-up TRUE -3 TimD
13-4* Logic Rules
13-40 Logic Rule Boolean 1 null 2 set-ups TRUE - Uint8
13-41 Logic Rule Operator 1 null 2 set-ups TRUE - Uint8
13-42 Logic Rule Boolean 2 null 2 set-ups TRUE - Uint8
13-43 Logic Rule Operator 2 null 2 set-ups TRUE - Uint8
13-44 Logic Rule Boolean 3 null 2 set-ups TRUE - Uint8
13-5* States
13-51 SL Controller Event null 2 set-ups TRUE - Uint8
13-52 SL Controller Action null 2 set-ups TRUE - Uint8

4-22 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

4.1.16 14-** Special Functions

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
14-0* Inverter Switching
14-00 Switching Pattern null All set-ups TRUE - Uint8
14-01 Switching Frequency null All set-ups TRUE - Uint8 4 4
14-03 Overmodulation [1] On All set-ups FALSE - Uint8
14-04 PWM Random [0] Off All set-ups TRUE - Uint8
14-06 Dead Time Compensation [1] On All set-ups TRUE - Uint8
14-1* Mains On/Off
14-10 Line Failure [0] No function All set-ups FALSE - Uint8
14-11 Line Voltage at Line Fault ExpressionLimit All set-ups TRUE 0 Uint16
14-12 Function at Mains Imbalance [0] Trip All set-ups TRUE - Uint8
14-13 Line Failure Step Factor 1.0 N/A All set-ups TRUE -1 Uint8
14-14 Kin. Backup Time Out 60 s All set-ups TRUE 0 Uint8
14-15 Kin. Backup Trip Recovery Level ExpressionLimit All set-ups TRUE -3 Uint32
14-2* Trip Reset
14-20 Reset Mode [0] Manual reset All set-ups TRUE - Uint8
14-21 Automatic Restart Time ExpressionLimit All set-ups TRUE 0 Uint16
14-22 Operation Mode [0] Normal operation All set-ups TRUE - Uint8
14-23 Typecode Setting null 2 set-ups FALSE - Uint8
14-24 Trip Delay at Current Limit 60 s All set-ups TRUE 0 Uint8
14-25 Trip Delay at Torque Limit 60 s All set-ups TRUE 0 Uint8
14-26 Trip Delay at Inverter Fault ExpressionLimit All set-ups TRUE 0 Uint8
14-28 Production Settings [0] No action All set-ups TRUE - Uint8
14-29 Service Code 0 N/A All set-ups TRUE 0 Int32
14-3* Current Limit Ctrl.
14-30 Current Lim Ctrl, Proportional Gain 100 % All set-ups FALSE 0 Uint16
14-31 Current Lim Ctrl, Integration Time 0.020 s All set-ups FALSE -3 Uint16
14-32 Current Lim Ctrl, Filter Time 1.0 ms All set-ups TRUE -4 Uint16
14-35 Stall Protection [1] Enabled All set-ups FALSE - Uint8
14-4* Energy Optimizing
14-40 VT Level 66 % All set-ups FALSE 0 Uint8
14-41 AEO Minimum Magnetization ExpressionLimit All set-ups TRUE 0 Uint8
14-42 Minimum AEO Frequency 10 Hz All set-ups TRUE 0 Uint8
14-43 Motor Cos-Phi ExpressionLimit All set-ups TRUE -2 Uint16
14-5* Environment
14-50 RFI 1 [1] On 1 set-up x FALSE - Uint8
14-51 DC Link Compensation [1] On 1 set-up TRUE - Uint8
14-52 Fan Control [0] Auto All set-ups TRUE - Uint8
14-53 Fan Monitor [1] Warning All set-ups TRUE - Uint8
14-55 Output Filter [0] No Filter All set-ups FALSE - Uint8
14-56 Capacitance Output Filter ExpressionLimit All set-ups FALSE -7 Uint16
14-57 Inductance Output Filter ExpressionLimit All set-ups FALSE -6 Uint16
14-59 Actual Number of Inverter Units ExpressionLimit 1 set-up x FALSE 0 Uint8
14-7* Compatibility
14-72 VLT Alarm Word 0 N/A All set-ups FALSE 0 Uint32
14-73 VLT Warning Word 0 N/A All set-ups FALSE 0 Uint32
14-74 VLT Ext. Status Word 0 N/A All set-ups FALSE 0 Uint32

MG33MD22 - VLT® is a registered Danfoss trademark 4-23

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
14-8* Options
14-80 Option Supplied by External 24 V DC [1] Yes 2 set-ups FALSE - Uint8
14-89 Option Detection [0] Protect Option Config. 1 set-up TRUE - Uint8
14-9* Fault Settings
4 4 14-90 Fault Level null 1 set-up TRUE - Uint8

4-24 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

4.1.17 15-** Drive Information

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
15-0* Operating Data
15-00 Operating Hours 0h All set-ups FALSE 74 Uint32
15-01 Running Hours 0h All set-ups FALSE 74 Uint32 4 4
15-02 kWh Counter 0 kWh All set-ups FALSE 75 Uint32
15-03 Power-ups 0 N/A All set-ups FALSE 0 Uint32
15-04 Over Temps 0 N/A All set-ups FALSE 0 Uint16
15-05 Over Volts 0 N/A All set-ups FALSE 0 Uint16
15-06 Reset kWh Counter [0] Do not reset All set-ups TRUE - Uint8
15-07 Reset Running Hours Counter [0] Do not reset All set-ups TRUE - Uint8
15-1* Data Log Settings
15-10 Logging Source 0 2 set-ups TRUE - Uint16
15-11 Logging Interval ExpressionLimit 2 set-ups TRUE -3 TimD
15-12 Trigger Event [0] FALSE 1 set-up TRUE - Uint8
15-13 Logging Mode [0] Log always 2 set-ups TRUE - Uint8
15-14 Samples Before Trigger 50 N/A 2 set-ups TRUE 0 Uint8
15-2* Historic Log
15-20 Historic Log: Event 0 N/A All set-ups FALSE 0 Uint8
15-21 Historic Log: Value 0 N/A All set-ups FALSE 0 Uint32
15-22 Historic Log: Time 0 ms All set-ups FALSE -3 Uint32
15-3* Fault Log
15-30 Fault Log: Error Code 0 N/A All set-ups FALSE 0 Uint8
15-31 Fault Log: Value 0 N/A All set-ups FALSE 0 Int16
15-32 Fault Log: Time 0s All set-ups FALSE 0 Uint32
15-4* Drive Identification
15-40 FC Type 0 N/A All set-ups FALSE 0 VisStr[6]
15-41 Power Section 0 N/A All set-ups FALSE 0 VisStr[20]
15-42 Voltage 0 N/A All set-ups FALSE 0 VisStr[20]
15-43 Software Version 0 N/A All set-ups FALSE 0 VisStr[5]
15-44 Ordered Typecode String 0 N/A All set-ups FALSE 0 VisStr[40]
15-45 Actual Typecode String 0 N/A All set-ups FALSE 0 VisStr[40]
15-46 Adj Freq Dr Ordering No. 0 N/A All set-ups FALSE 0 VisStr[8]
15-47 Power Card Ordering No. 0 N/A All set-ups FALSE 0 VisStr[8]
15-48 LCP ID Num. 0 N/A All set-ups FALSE 0 VisStr[20]
15-49 SW ID Control Card 0 N/A All set-ups FALSE 0 VisStr[20]
15-50 SW ID Power Card 0 N/A All set-ups FALSE 0 VisStr[20]
15-51 Adj Freq Dr Serial No. 0 N/A All set-ups FALSE 0 VisStr[10]
15-53 Power Card Serial Number 0 N/A All set-ups FALSE 0 VisStr[19]
15-58 Smart Setup Filename ExpressionLimit 1 set-up FALSE 0 VisStr[16]
15-59 CSIV Filename ExpressionLimit 1 set-up FALSE 0 VisStr[16]
15-6* Option Ident
15-60 Option Mounted 0 N/A All set-ups FALSE 0 VisStr[30]
15-61 Option SW Version 0 N/A All set-ups FALSE 0 VisStr[20]
15-62 Option Ordering No 0 N/A All set-ups FALSE 0 VisStr[8]
15-63 Option Serial No 0 N/A All set-ups FALSE 0 VisStr[18]
15-70 Option in Slot A 0 N/A All set-ups FALSE 0 VisStr[30]
15-71 Slot A Option SW Version 0 N/A All set-ups FALSE 0 VisStr[20]

MG33MD22 - VLT® is a registered Danfoss trademark 4-25

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
15-72 Option in Slot B 0 N/A All set-ups FALSE 0 VisStr[30]
15-73 Slot B Option SW Version 0 N/A All set-ups FALSE 0 VisStr[20]
15-74 Option in Slot C0 0 N/A All set-ups FALSE 0 VisStr[30]
15-75 Slot C0 Option SW Version 0 N/A All set-ups FALSE 0 VisStr[20]
4 4 15-76 Option in Slot C1 0 N/A All set-ups FALSE 0 VisStr[30]
15-77 Slot C1 Option SW Version 0 N/A All set-ups FALSE 0 VisStr[20]
15-9* Parameter Info
15-92 Defined Parameters 0 N/A All set-ups FALSE 0 Uint16
15-93 Modified Parameters 0 N/A All set-ups FALSE 0 Uint16
15-98 Drive Identification 0 N/A All set-ups FALSE 0 VisStr[40]
15-99 Parameter Metadata 0 N/A All set-ups FALSE 0 Uint16

4-26 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

4.1.18 16-** Data Readouts

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
16-0* General Status
16-00 Control Word 0 N/A All set-ups FALSE 0 V2
0.000 ReferenceFeed- 4 4
16-01 Reference [Unit] backUnit All set-ups FALSE -3 Int32
16-02 Reference % 0.0 % All set-ups FALSE -1 Int16
16-03 Status Word 0 N/A All set-ups FALSE 0 V2
16-05 Main Actual Value [%] 0.00 % All set-ups FALSE -2 N2
16-09 Custom Readout 0.00 CustomReadoutUnit All set-ups FALSE -2 Int32
16-1* Motor Status
16-10 Power [kW] 0.00 kW All set-ups FALSE 1 Int32
16-11 Power [hp] 0.00 hp All set-ups FALSE -2 Int32
16-12 Motor voltage 0.0 V All set-ups FALSE -1 Uint16
16-13 Frequency 0.0 Hz All set-ups FALSE -1 Uint16
16-14 Motor Current 0.00 A All set-ups FALSE -2 Int32
16-15 Frequency [%] 0.00 % All set-ups FALSE -2 N2
16-16 Torque [Nm] 0.0 Nm All set-ups FALSE -1 Int16
16-17 Speed [RPM] 0 RPM All set-ups FALSE 67 Int32
16-18 Motor Thermal 0% All set-ups FALSE 0 Uint8
16-19 KTY sensor temperature 0 °C All set-ups FALSE 100 Int16
16-20 Motor Angle 0 N/A All set-ups TRUE 0 Uint16
16-21 Torque [%] High Res. 0.0 % All set-ups FALSE -1 Int16
16-22 Torque [%] 0% All set-ups FALSE 0 Int16
16-25 Torque [Nm] High 0.0 Nm All set-ups FALSE -1 Int32
16-3* Drive Status
16-30 DC Link Voltage 0V All set-ups FALSE 0 Uint16
16-32 Brake Energy /s 0.000 kW All set-ups FALSE 0 Uint32
16-33 Brake Energy /2 min 0.000 kW All set-ups FALSE 0 Uint32
16-34 Heatsink Temp. 0 °C All set-ups FALSE 100 Uint8
16-35 Inverter Thermal 0% All set-ups FALSE 0 Uint8
16-36 Inv. Nom. Current ExpressionLimit All set-ups FALSE -2 Uint32
16-37 Inv. Max. Current ExpressionLimit All set-ups FALSE -2 Uint32
16-38 SL Controller State 0 N/A All set-ups FALSE 0 Uint8
16-39 Control Card Temp. 0 °C All set-ups FALSE 100 Uint8
16-40 Logging Buffer Full [0] No All set-ups TRUE - Uint8
VisStr[5
16-41 LCP Bottom Statusline 0 N/A All set-ups TRUE 0 0]
16-49 Current Fault Source 0 N/A All set-ups x TRUE 0 Uint8
16-5* Ref. & Feedb.
16-50 External Reference 0.0 N/A All set-ups FALSE -1 Int16
16-51 Pulse Reference 0.0 N/A All set-ups FALSE -1 Int16
0.000 ReferenceFeed-
16-52 Feedback [Unit] backUnit All set-ups FALSE -3 Int32
16-53 Digi Pot Reference 0.00 N/A All set-ups FALSE -2 Int16
16-57 Feedback [RPM] 0 RPM All set-ups FALSE 67 Int32
16-6* Inputs & Outputs
16-60 Digital Input 0 N/A All set-ups FALSE 0 Uint16

MG33MD22 - VLT® is a registered Danfoss trademark 4-27

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
16-61 Terminal 53 Switch Setting [0] Current All set-ups FALSE - Uint8
16-62 Analog Input 53 0.000 N/A All set-ups FALSE -3 Int32
16-63 Terminal 54 Switch Setting [0] Current All set-ups FALSE - Uint8
16-64 Analog Input 54 0.000 N/A All set-ups FALSE -3 Int32
4 4 16-65 Analog Output 42 [mA] 0.000 N/A All set-ups FALSE -3 Int16
16-66 Digital Output [bin] 0 N/A All set-ups FALSE 0 Int16
16-67 Freq. Input #29 [Hz] 0 N/A All set-ups x FALSE 0 Int32
16-68 Freq. Input #33 [Hz] 0 N/A All set-ups FALSE 0 Int32
16-69 Pulse Output #27 [Hz] 0 N/A All set-ups FALSE 0 Int32
16-70 Pulse Output #29 [Hz] 0 N/A All set-ups x FALSE 0 Int32
16-71 Relay Output [bin] 0 N/A All set-ups FALSE 0 Int16
16-72 Counter A 0 N/A All set-ups TRUE 0 Int32
16-73 Counter B 0 N/A All set-ups TRUE 0 Int32
16-74 Prec. Stop Counter 0 N/A All set-ups TRUE 0 Uint32
16-75 Analog In X30/11 0.000 N/A All set-ups FALSE -3 Int32
16-76 Analog In X30/12 0.000 N/A All set-ups FALSE -3 Int32
16-77 Analog Out X30/8 [mA] 0.000 N/A All set-ups FALSE -3 Int16
16-78 Analog Out X45/1 [mA] 0.000 N/A All set-ups FALSE -3 Int16
16-79 Analog Out X45/3 [mA] 0.000 N/A All set-ups FALSE -3 Int16
16-8* Fieldbus & FC Port
16-80 Fieldbus CTW 1 0 N/A All set-ups FALSE 0 V2
16-82 Fieldbus REF 1 0 N/A All set-ups FALSE 0 N2
16-84 Comm. Option Status 0 N/A All set-ups FALSE 0 V2
16-85 FC Port CTW 1 0 N/A All set-ups FALSE 0 V2
16-86 FC Port REF 1 0 N/A All set-ups FALSE 0 N2
16-9* Diagnosis Readouts
16-90 Alarm Word 0 N/A All set-ups FALSE 0 Uint32
16-91 Alarm word 2 0 N/A All set-ups FALSE 0 Uint32
16-92 Warning Word 0 N/A All set-ups FALSE 0 Uint32
16-93 Warning word 2 0 N/A All set-ups FALSE 0 Uint32
16-94 Ext. Status Word 0 N/A All set-ups FALSE 0 Uint32

4-28 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

4.1.19 17-** Motor Feedb.Option

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
17-1* Inc. Enc. Interface
17-10 Signal Type [1] TTL (5V, RS4222) All set-ups FALSE - Uint8
17-11 Resolution (PPR) 1024 N/A All set-ups FALSE 0 Uint16 4 4
17-2* Abs. Enc. Interface
17-20 Protocol Selection [0] None All set-ups FALSE - Uint8
17-21 Resolution (Positions/Rev) ExpressionLimit All set-ups FALSE 0 Uint32
17-24 SSI Data Length 13 N/A All set-ups FALSE 0 Uint8
17-25 Clock Rate ExpressionLimit All set-ups FALSE 3 Uint16
17-26 SSI Data Format [0] Gray code All set-ups FALSE - Uint8
17-34 HIPERFACE Baud rate [4] 9600 All set-ups FALSE - Uint8
17-5* Resolver Interface
17-50 Poles 2 N/A 1 set-up FALSE 0 Uint8
17-51 Input Voltage 7.0 V 1 set-up FALSE -1 Uint8
17-52 Input Frequency 10.0 kHz 1 set-up FALSE 2 Uint8
17-53 Transformation Ratio 0.5 N/A 1 set-up FALSE -1 Uint8
17-56 Encoder Sim. Resolution [0] Disabled 1 set-up FALSE - Uint8
17-59 Resolver Interface [0] Disabled All set-ups FALSE - Uint8
17-6* Monitoring and App.
17-60 Feedback Direction [0] Clockwise All set-ups FALSE - Uint8
17-61 Feedback Signal Monitoring [1] Warning All set-ups TRUE - Uint8

4.1.20 18-** Data Readouts 2

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
18-3* Analog Readouts
18-36 Analog Input X48/2 [mA] 0.000 N/A All set-ups TRUE -3 Int32
18-37 Temp. Input X48/4 0 N/A All set-ups TRUE 0 Int16
18-38 Temp. Input X48/7 0 N/A All set-ups TRUE 0 Int16
18-39 Temp. Input X48/10 0 N/A All set-ups TRUE 0 Int16
18-6* Inputs & Outputs 2
18-60 Digital Input 2 0 N/A All set-ups FALSE 0 Uint16
18-9* PID Readouts
18-90 Process PID Error 0.0 % All set-ups FALSE -1 Int16
18-91 Process PID Output 0.0 % All set-ups FALSE -1 Int16
18-92 Process PID Clamped Output 0.0 % All set-ups FALSE -1 Int16
18-93 Process PID Gain Scaled Output 0.0 % All set-ups FALSE -1 Int16

MG33MD22 - VLT® is a registered Danfoss trademark 4-29

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

4.1.21 30-** Special Features

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
30-0* Wobbler
30-00 Wobble Mode [0] Abs. Freq., Abs. Time All set-ups FALSE - Uint8
4 4 30-01 Wobble Delta Frequency [Hz] 5.0 Hz All set-ups TRUE -1 Uint8
30-02 Wobble Delta Frequency [%] 25 % All set-ups TRUE 0 Uint8
30-03 Wobble Delta Freq. Scaling Resource [0] No function All set-ups TRUE - Uint8
30-04 Wobble Jump Frequency [Hz] 0.0 Hz All set-ups TRUE -1 Uint8
30-05 Wobble Jump Frequency [%] 0% All set-ups TRUE 0 Uint8
30-06 Wobble Jump Time ExpressionLimit All set-ups TRUE -3 Uint16
30-07 Wobble Sequence Time 10.0 s All set-ups TRUE -1 Uint16
30-08 Wobble Up/Down Time 5.0 s All set-ups TRUE -1 Uint16
30-09 Wobble Random Function [0] Off All set-ups TRUE - Uint8
30-10 Wobble Ratio 1.0 N/A All set-ups TRUE -1 Uint8
30-11 Wobble Random Ratio Max. 10.0 N/A All set-ups TRUE -1 Uint8
30-12 Wobble Random Ratio Min. 0.1 N/A All set-ups TRUE -1 Uint8
30-19 Wobble Delta Freq. Scaled 0.0 Hz All set-ups FALSE -1 Uint16
30-2* Adv. Start Adjust
30-20 High Starting Torque Time [s] 0.00 s All set-ups x TRUE -2 Uint16
30-21 High Starting Torque Current [%] 100.0 % All set-ups x TRUE -1 Uint32
30-22 Locked Rotor Protection [0] Off All set-ups x TRUE - Uint8
30-23 Locked Rotor Detection Time [s] 0.10 s All set-ups x TRUE -2 Uint8
30-8* Compatibility (I)
30-80 d-axis inductance (Ld) ExpressionLimit All set-ups x FALSE -6 Int32
30-81 Brake Resistor (ohm) ExpressionLimit 1 set-up TRUE -2 Uint32
30-83 Speed PID Proportional Gain ExpressionLimit All set-ups TRUE -4 Uint32
30-84 Process PID Proportional Gain 0.100 N/A All set-ups TRUE -3 Uint16

4-30 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

4.1.22 32-** MCO Basic Settings

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
32-0* Encoder 2
32-00 Incremental Signal Type [1] TTL (5V, RS4222) 2 set-ups TRUE - Uint8
32-01 Incremental Resolution 1024 N/A 2 set-ups TRUE 0 Uint32 4 4
32-02 Absolute Protocol [0] None 2 set-ups TRUE - Uint8
32-03 Absolute Resolution 8192 N/A 2 set-ups TRUE 0 Uint32
32-04 Absolute Encoder Baudrate X55 [4] 9600 All set-ups FALSE - Uint8
32-05 Absolute Encoder Data Length 25 N/A 2 set-ups TRUE 0 Uint8
32-06 Absolute Encoder Clock Frequency 262.000 kHz 2 set-ups TRUE 0 Uint32
32-07 Absolute Encoder Clock Generation [1] On 2 set-ups TRUE - Uint8
32-08 Absolute Encoder Cable Length 0m 2 set-ups TRUE 0 Uint16
32-09 Encoder Monitoring [0] Off 2 set-ups TRUE - Uint8
32-10 Rotational Direction [1] No action 2 set-ups TRUE - Uint8
32-11 User Unit Denominator 1 N/A 2 set-ups TRUE 0 Uint32
32-12 User Unit Numerator 1 N/A 2 set-ups TRUE 0 Uint32
32-13 Enc.2 Control [0] No soft changing 2 set-ups TRUE - Uint8
32-14 Enc.2 node ID 127 N/A 2 set-ups TRUE 0 Uint8
32-15 Enc.2 CAN guard null 2 set-ups TRUE - Uint8
32-3* Encoder 1
32-30 Incremental Signal Type [1] TTL (5V, RS4222) 2 set-ups TRUE - Uint8
32-31 Incremental Resolution 1024 N/A 2 set-ups TRUE 0 Uint32
32-32 Absolute Protocol [0] None 2 set-ups TRUE - Uint8
32-33 Absolute Resolution 8192 N/A 2 set-ups TRUE 0 Uint32
32-35 Absolute Encoder Data Length 25 N/A 2 set-ups TRUE 0 Uint8
32-36 Absolute Encoder Clock Frequency 262.000 kHz 2 set-ups TRUE 0 Uint32
32-37 Absolute Encoder Clock Generation [1] On 2 set-ups TRUE - Uint8
32-38 Absolute Encoder Cable Length 0m 2 set-ups TRUE 0 Uint16
32-39 Encoder Monitoring [0] Off 2 set-ups TRUE - Uint8
32-40 Encoder Termination [1] On 2 set-ups TRUE - Uint8
32-43 Enc.1 Control [0] No soft changing 2 set-ups TRUE - Uint8
32-44 Enc.1 node ID 127 N/A 2 set-ups TRUE 0 Uint8
32-45 Enc.1 CAN guard null 2 set-ups TRUE - Uint8
32-5* Feedback Source
32-50 Source Slave [2] Encoder 2 2 set-ups TRUE - Uint8
32-51 MCO 302 Last Will [1] Trip 2 set-ups TRUE - Uint8
32-52 Source Master [1] Encoder 1 X56 2 set-ups TRUE - Uint8
32-6* PID Controller
32-60 Proportional factor 30 N/A 2 set-ups TRUE 0 Uint32
32-61 Derivative factor 0 N/A 2 set-ups TRUE 0 Uint32
32-62 Integral factor 0 N/A 2 set-ups TRUE 0 Uint32
32-63 Limit Value for Integral Sum 1000 N/A 2 set-ups TRUE 0 Uint16
32-64 PID Bandwidth 1000 N/A 2 set-ups TRUE 0 Uint16
32-65 Velocity Feed-Forward 0 N/A 2 set-ups TRUE 0 Uint32
32-66 Acceleration Feed-Forward 0 N/A 2 set-ups TRUE 0 Uint32
32-67 Max. Tolerated Position Error 20000 N/A 2 set-ups TRUE 0 Uint32
32-68 Reverse Behavior for Slave [0] Reversing allowed 2 set-ups TRUE - Uint8
32-69 Sampling Time for PID Control 1 ms 2 set-ups TRUE -3 Uint16

MG33MD22 - VLT® is a registered Danfoss trademark 4-31

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
32-70 Scan Time for Profile Generator 1 ms 2 set-ups TRUE -3 Uint8
32-71 Size of the Control Window (Activation) 0 N/A 2 set-ups TRUE 0 Uint32
32-72 Size of the Control Window (Deactiv.) 0 N/A 2 set-ups TRUE 0 Uint32
32-73 Integral limit filter time 0 ms 2 set-ups TRUE -3 Int16
4 4 32-74 Position error filter time 0 ms 2 set-ups TRUE -3 Int16
32-8* Velocity & Accel.
32-80 Maximum Velocity (Encoder) 1500 RPM 2 set-ups TRUE 67 Uint32
32-81 Shortest Ramp 1.000 s 2 set-ups TRUE -3 Uint32
32-82 Ramp Type [0] Linear 2 set-ups TRUE - Uint8
32-83 Velocity Resolution 100 N/A 2 set-ups TRUE 0 Uint32
32-84 Default Velocity 50 N/A 2 set-ups TRUE 0 Uint32
32-85 Default Acceleration 50 N/A 2 set-ups TRUE 0 Uint32
32-86 Acc. up for limited jerk 100 ms 2 set-ups TRUE -3 Uint32
32-87 Acc. down for limited jerk 0 ms 2 set-ups TRUE -3 Uint32
32-88 Dec. up for limited jerk 0 ms 2 set-ups TRUE -3 Uint32
32-89 Dec. down for limited jerk 0 ms 2 set-ups TRUE -3 Uint32
32-9* Development
32-90 Debug Source [0] Controlcard 2 set-ups TRUE - Uint8

4-32 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

4.1.23 33-** MCO Adv. Settings

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
33-0* Home Motion
33-00 Force HOME [0] Home not forced 2 set-ups TRUE - Uint8
33-01 Zero Point Offset from Home Pos. 0 N/A 2 set-ups TRUE 0 Int32 4 4
33-02 Ramp for Home Motion 10 N/A 2 set-ups TRUE 0 Uint32
33-03 Velocity of Home Motion 10 N/A 2 set-ups TRUE 0 Int32
33-04 Behavior during Home Motion [0] Reverse and index 2 set-ups TRUE - Uint8
33-1* Synchronization
33-10 Synchronization Factor Master (M:S) 1 N/A 2 set-ups TRUE 0 Int32
33-11 Synchronization Factor Slave (M:S) 1 N/A 2 set-ups TRUE 0 Int32
33-12 Position Offset for Synchronization 0 N/A 2 set-ups TRUE 0 Int32
33-13 Accuracy Window for Position Sync. 1000 N/A 2 set-ups TRUE 0 Int32
33-14 Relative Slave Velocity Limit 0% 2 set-ups TRUE 0 Uint8
33-15 Marker Number for Master 1 N/A 2 set-ups TRUE 0 Uint16
33-16 Marker Number for Slave 1 N/A 2 set-ups TRUE 0 Uint16
33-17 Master Marker Distance 4096 N/A 2 set-ups TRUE 0 Uint32
33-18 Slave Marker Distance 4096 N/A 2 set-ups TRUE 0 Uint32
33-19 Master Marker Type [0] Encoder Z positive 2 set-ups TRUE - Uint8
33-20 Slave Marker Type [0] Encoder Z positive 2 set-ups TRUE - Uint8
33-21 Master Marker Tolerance Window 0 N/A 2 set-ups TRUE 0 Uint32
33-22 Slave Marker Tolerance Window 0 N/A 2 set-ups TRUE 0 Uint32
33-23 Start Behavior for Marker Sync [0] Start Function 1 2 set-ups TRUE - Uint16
33-24 Marker Number for Fault 10 N/A 2 set-ups TRUE 0 Uint16
33-25 Marker Number for Ready 1 N/A 2 set-ups TRUE 0 Uint16
33-26 Velocity Filter 0 us 2 set-ups TRUE -6 Int32
33-27 Offset Filter Time 0 ms 2 set-ups TRUE -3 Uint32
33-28 Marker Filter Configuration [0] Marker filter 1 2 set-ups TRUE - Uint8
33-29 Filter Time for Marker Filter 0 ms 2 set-ups TRUE -3 Int32
33-30 Maximum Marker Correction 0 N/A 2 set-ups TRUE 0 Uint32
33-31 Synchronization Type [0] Standard 2 set-ups TRUE - Uint8
33-32 Feed Forward Velocity Adaptation 0 N/A 2 set-ups TRUE 0 Uint32
33-33 Velocity Filter Window 0 N/A 2 set-ups TRUE 0 Uint32
33-34 Slave Marker filter time 0 ms 2 set-ups TRUE -3 Uint32
33-4* Limit Handling
33-40 Behavior at End Limit Switch [0] Call error handler 2 set-ups TRUE - Uint8
33-41 Negative Software End Limit -500000 N/A 2 set-ups TRUE 0 Int32
33-42 Positive Software End Limit 500000 N/A 2 set-ups TRUE 0 Int32
33-43 Negative Software End Limit Active [0] Inactive 2 set-ups TRUE - Uint8
33-44 Positive Software End Limit Active [0] Inactive 2 set-ups TRUE - Uint8
33-45 Time in Target Window 0 ms 2 set-ups TRUE -3 Uint8
33-46 Target Window LimitValue 1 N/A 2 set-ups TRUE 0 Uint16
33-47 Size of Target Window 0 N/A 2 set-ups TRUE 0 Uint16
33-5* I/O Configuration
33-50 Terminal X57/1 Digital Input [0] No function 2 set-ups TRUE - Uint8
33-51 Terminal X57/2 Digital Input [0] No function 2 set-ups TRUE - Uint8
33-52 Terminal X57/3 Digital Input [0] No function 2 set-ups TRUE - Uint8
33-53 Terminal X57/4 Digital Input [0] No function 2 set-ups TRUE - Uint8

MG33MD22 - VLT® is a registered Danfoss trademark 4-33

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
33-54 Terminal X57/5 Digital Input [0] No function 2 set-ups TRUE - Uint8
33-55 Terminal X57/6 Digital Input [0] No function 2 set-ups TRUE - Uint8
33-56 Terminal X57/7 Digital Input [0] No function 2 set-ups TRUE - Uint8
33-57 Terminal X57/8 Digital Input [0] No function 2 set-ups TRUE - Uint8
4 4 33-58 Terminal X57/9 Digital Input [0] No function 2 set-ups TRUE - Uint8
33-59 Terminal X57/10 Digital Input [0] No function 2 set-ups TRUE - Uint8
33-60 Terminal X59/1 and X59/2 Mode [1] Output 2 set-ups FALSE - Uint8
33-61 Terminal X59/1 Digital Input [0] No function 2 set-ups TRUE - Uint8
33-62 Terminal X59/2 Digital Input [0] No function 2 set-ups TRUE - Uint8
33-63 Terminal X59/1 Digital Output [0] No function 2 set-ups TRUE - Uint8
33-64 Terminal X59/2 Digital Output [0] No function 2 set-ups TRUE - Uint8
33-65 Terminal X59/3 Digital Output [0] No function 2 set-ups TRUE - Uint8
33-66 Terminal X59/4 Digital Output [0] No function 2 set-ups TRUE - Uint8
33-67 Terminal X59/5 Digital Output [0] No function 2 set-ups TRUE - Uint8
33-68 Terminal X59/6 Digital Output [0] No function 2 set-ups TRUE - Uint8
33-69 Terminal X59/7 Digital Output [0] No function 2 set-ups TRUE - Uint8
33-70 Terminal X59/8 Digital Output [0] No function 2 set-ups TRUE - Uint8
33-8* Global Parameters
33-80 Activated Program Number -1 N/A 2 set-ups TRUE 0 Int8
33-81 Power-up State [1] Motor ON 2 set-ups TRUE - Uint8
33-82 Drive Status Monitoring [1] On 2 set-ups TRUE - Uint8
33-83 Behavior After Error [0] Coast 2 set-ups TRUE - Uint8
33-84 Behavior afterEsc. [0] Controlled stop 2 set-ups TRUE - Uint8
33-85 MCO Supplied by External 24VDC [0] No 2 set-ups TRUE - Uint8
33-86 Terminal at alarm [0] Relay 1 2 set-ups TRUE - Uint8
33-87 Terminal state at alarm [0] Do nothing 2 set-ups TRUE - Uint8
33-88 Status word at alarm 0 N/A 2 set-ups TRUE 0 Uint16
33-9* MCO Port Settings
33-90 X62 MCO CAN node ID 127 N/A 2 set-ups TRUE 0 Uint8
33-91 X62 MCO CAN baud rate [20] 125 Kbps 2 set-ups TRUE - Uint8
33-94 X60 MCO RS485 serial termination [0] Off 2 set-ups TRUE - Uint8
33-95 X60 MCO RS485 serial baud rate [2] 9600 Baud 2 set-ups TRUE - Uint8

4-34 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

4.1.24 34-** MCO Data Readouts

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
34-0* PCD Write Par.
34-01 PCD 1 Write to MCO 0 N/A All set-ups TRUE 0 Uint16
34-02 PCD 2 Write to MCO 0 N/A All set-ups TRUE 0 Uint16 4 4
34-03 PCD 3 Write to MCO 0 N/A All set-ups TRUE 0 Uint16
34-04 PCD 4 Write to MCO 0 N/A All set-ups TRUE 0 Uint16
34-05 PCD 5 Write to MCO 0 N/A All set-ups TRUE 0 Uint16
34-06 PCD 6 Write to MCO 0 N/A All set-ups TRUE 0 Uint16
34-07 PCD 7 Write to MCO 0 N/A All set-ups TRUE 0 Uint16
34-08 PCD 8 Write to MCO 0 N/A All set-ups TRUE 0 Uint16
34-09 PCD 9 Write to MCO 0 N/A All set-ups TRUE 0 Uint16
34-10 PCD 10 Write to MCO 0 N/A All set-ups TRUE 0 Uint16
34-2* PCD Read Par.
34-21 PCD 1 Read from MCO 0 N/A All set-ups TRUE 0 Uint16
34-22 PCD 2 Read from MCO 0 N/A All set-ups TRUE 0 Uint16
34-23 PCD 3 Read from MCO 0 N/A All set-ups TRUE 0 Uint16
34-24 PCD 4 Read from MCO 0 N/A All set-ups TRUE 0 Uint16
34-25 PCD 5 Read from MCO 0 N/A All set-ups TRUE 0 Uint16
34-26 PCD 6 Read from MCO 0 N/A All set-ups TRUE 0 Uint16
34-27 PCD 7 Read from MCO 0 N/A All set-ups TRUE 0 Uint16
34-28 PCD 8 Read from MCO 0 N/A All set-ups TRUE 0 Uint16
34-29 PCD 9 Read from MCO 0 N/A All set-ups TRUE 0 Uint16
34-30 PCD 10 Read from MCO 0 N/A All set-ups TRUE 0 Uint16
34-4* Inputs & Outputs
34-40 Digital Inputs 0 N/A All set-ups TRUE 0 Uint16
34-41 Digital Outputs 0 N/A All set-ups TRUE 0 Uint16
34-5* Process Data
34-50 Actual Position 0 N/A All set-ups TRUE 0 Int32
34-51 Commanded Position 0 N/A All set-ups TRUE 0 Int32
34-52 Actual Master Position 0 N/A All set-ups TRUE 0 Int32
34-53 Slave Index Position 0 N/A All set-ups TRUE 0 Int32
34-54 Master Index Position 0 N/A All set-ups TRUE 0 Int32
34-55 Curve Position 0 N/A All set-ups TRUE 0 Int32
34-56 Track Error 0 N/A All set-ups TRUE 0 Int32
34-57 Synchronizing Error 0 N/A All set-ups TRUE 0 Int32
34-58 Actual Velocity 0 N/A All set-ups TRUE 0 Int32
34-59 Actual Master Velocity 0 N/A All set-ups TRUE 0 Int32
34-60 Synchronizing Status 0 N/A All set-ups TRUE 0 Int32
34-61 Axis Status 0 N/A All set-ups TRUE 0 Int32
34-62 Program Status 0 N/A All set-ups TRUE 0 Int32
34-64 MCO 302 Status 0 N/A All set-ups TRUE 0 Uint16
34-65 MCO 302 Control 0 N/A All set-ups TRUE 0 Uint16
34-7* Diagnosis readouts
34-70 MCO Alarm Word 1 0 N/A All set-ups FALSE 0 Uint32
34-71 MCO Alarm Word 2 0 N/A All set-ups FALSE 0 Uint32

MG33MD22 - VLT® is a registered Danfoss trademark 4-35

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Parameter Lists FC 300 Programming Guide

4.1.25 35-** Sensor Input Option

Par. Parameter description Default value 4-set-up FC 302 Change Conver- Type
No. only during sion
# operation index
35-0* Temp. Input Mode
35-00 Term. X48/4 Temp. Unit [60] °C All set-ups TRUE - Uint8
4 4 35-01 Term. X48/4 Input Type [0] Not Connected All set-ups TRUE - Uint8
35-02 Term. X48/7 Temp. Unit [60] °C All set-ups TRUE - Uint8
35-03 Term. X48/7 Input Type [0] Not Connected All set-ups TRUE - Uint8
35-04 Term. X48/10 Temp. Unit [60] °C All set-ups TRUE - Uint8
35-05 Term. X48/10 Input Type [0] Not Connected All set-ups TRUE - Uint8
35-06 Temperature Sensor Alarm Function [5] Stop and trip All set-ups TRUE - Uint8
35-1* Temp. Input X48/4
35-14 Term. X48/4 Filter Time Constant 0.001 s All set-ups TRUE -3 Uint16
35-15 Term. X48/4 Temp. Monitor [0] Disabled All set-ups TRUE - Uint8
35-16 Term. X48/4 Low Temp. Limit ExpressionLimit All set-ups TRUE 0 Int16
35-17 Term. X48/4 High Temp. Limit ExpressionLimit All set-ups TRUE 0 Int16
35-2* Temp. Input X48/7
35-24 Term. X48/7 Filter Time Constant 0.001 s All set-ups TRUE -3 Uint16
35-25 Term. X48/7 Temp. Monitor [0] Disabled All set-ups TRUE - Uint8
35-26 Term. X48/7 Low Temp. Limit ExpressionLimit All set-ups TRUE 0 Int16
35-27 Term. X48/7 High Temp. Limit ExpressionLimit All set-ups TRUE 0 Int16
35-3* Temp. Input X48/10
35-34 Term. X48/10 Filter Time Constant 0.001 s All set-ups TRUE -3 Uint16
35-35 Term. X48/10 Temp. Monitor [0] Disabled All set-ups TRUE - Uint8
35-36 Term. X48/10 Low Temp. Limit ExpressionLimit All set-ups TRUE 0 Int16
35-37 Term. X48/10 High Temp. Limit ExpressionLimit All set-ups TRUE 0 Int16
35-4* Analog Input X48/2
35-42 Term. X48/2 Low Current 4.00 mA All set-ups TRUE -5 Int16
35-43 Term. X48/2 High Current 20.00 mA All set-ups TRUE -5 Int16
35-44 Term. X48/2 Low Ref./Feedb. Value 0.000 N/A All set-ups TRUE -3 Int32
35-45 Term. X48/2 High Ref./Feedb. Value 100.000 N/A All set-ups TRUE -3 Int32
35-46 Term. X48/2 Filter Time Constant 0.001 s All set-ups TRUE -3 Uint16

4-36 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Troubleshooting FC 300 Programming Guide

5 Troubleshooting

5.1.1 Warnings/Alarm Messages If an alarm cannot be reset, the reason may be that its
cause has not been rectified, or the alarm is trip-locked
A warning or an alarm is signaled by the relevant LED on (see also table on following page).
the front of the Adjustable frequency drive and indicated
by a code on the display. Alarms that are trip-locked offer additional protection,
meaning that the line power supply must be switched off
A warning remains active until its cause is no longer
present. Under certain circumstances operation of the
before the alarm can be reset. After being switched back
on, the Adjustable frequency drive is no longer blocked
5 5
motor may still be continued. Warning messages may be and may be reset as described above once the cause has
critical, but are not necessarily so. been rectified.

In the event of an alarm, the Adjustable frequency drive Alarms that are not trip-locked can also be reset using the
will have tripped. Alarms must be reset to restart operation automatic reset function in 14-20 Reset Mode (Warning:
once their cause has been rectified. automatic wake-up is possible!)

This may be done in three ways: If a warning and alarm are marked against a code in the
1. By using the [RESET] control button on the LCP. table on the following page, this means that either a
warning occurs before an alarm, or that you can specify
2. Via a digital input with the “Reset” function.
whether it is a warning or an alarm that is to be displayed
3. Via serial communication/optional serial for a given fault.
communication bus.

NOTE! This is possible, for instance, in 1-90 Motor Thermal

After a manual reset using the [RESET] button on the LCP, Protection. After an alarm or trip, the motor carries on
the [AUTO ON] button must be pressed to restart the coasting, and the alarm and warning flash. Once the
motor. problem has been rectified, only the alarm continues
flashing until the Adjustable frequency drive is reset.

No. Description Warning Alarm/Trip Alarm/Trip Lock Parameter

Reference
1 10 Volts low X
2 Live zero error (X) (X) 6-01 Live Zero Timeout
Function
3 No motor (X) 1-80 Function at Stop
4 Line phase loss (X) (X) (X) 14-12 Function at Mains
Imbalance
5 DC link voltage high X
6 DC link voltage low X
7 DC overvoltage X X
8 DC under-voltage X X
9 Inverter overloaded X X
10 Motor ETR over-temperature (X) (X) 1-90 Motor Thermal
Protection
11 Motor thermistor over-temperature (X) (X) 1-90 Motor Thermal
Protection
12 Torque limit X X
13 Overcurrent X X X
14 Ground Fault X X X
15 Hardware mismatch X X
16 Short Circuit X X

MG33MD22 - VLT® is a registered Danfoss trademark 5-1

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Troubleshooting FC 300 Programming Guide

No. Description Warning Alarm/Trip Alarm/Trip Lock Parameter

Reference
17 Control word timeout (X) (X) 8-04 Control Word
Timeout Function
20 Temp. Input Error
21 Param Error
22 Hoist Mech. Brake (X) (X) Parameter group 2-2*
23 Internal Fans X
24 External Fans X
25 Brake resistor short-circuited X
5 5 26 Brake resistor power limit (X) (X) 2-13 Brake Power
Monitoring
27 Brake chopper short-circuited X X
28 Brake check (X) (X) 2-15 Brake Check
29 Heatsink temp X X X
30 Motor phase U missing (X) (X) (X) 4-58 Missing Motor
Phase Function
31 Motor phase V missing (X) (X) (X) 4-58 Missing Motor
Phase Function
32 Motor phase W missing (X) (X) (X) 4-58 Missing Motor
Phase Function
33 Soft-charge Fault X X
34 Fieldbus communication fault X X
35 Option Fault
36 Line failure X X
37 Phase imbalance X
38 Internal Fault X X
39 Heatsink sensor X X
40 Overload of Digital Output Terminal 27 (X) 5-00 Digital I/O Mode,
5-01 Terminal 27 Mode
41 Overload of Digital Output Terminal 29 (X) 5-00 Digital I/O Mode,
5-02 Terminal 29 Mode
42 Ovrld X30/6-7 (X)
43 Ext. Supply (option)
45 Ground Fault 2 X X X
46 Pwr. card supply X X
47 24 V supply low X X X
48 1.8 V supply low X X
49 Speed limit X
50 AMA calibration failed X
51 AMA check Unom and Inom X
52 AMA low Inom X
53 AMA motor too big X
54 AMA motor too small X
55 AMA parameter out of range X
56 AMA interrupted by user X
57 AMA timeout X
58 AMA internal fault X X
59 Current limit X
60 External Interlock X X

5-2 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Troubleshooting FC 300 Programming Guide

No. Description Warning Alarm/Trip Alarm/Trip Lock Parameter

Reference
61 Feedback Error (X) (X) 4-30 Motor Feedback
Loss Function
62 Output Frequency at Maximum Limit X
63 Mechanical Brake Low (X) 2-20 Release Brake
Current
64 Voltage Limit X
65 Control Board Over-temperature X X X
66
67
Heat sink Temperature Low
Option Configuration has Changed
X
X
5 5
68 Safe Stop (X) (X)1) 5-19 Terminal 37 Safe
Stop
69 Pwr. Card Temp X X
70 Illegal FC configuration X
71 PTC 1 Safe Stop
72 Dangerous failure
73 Safe Stop Auto Restart (X) (X) 5-19 Terminal 37 Safe
Stop
74 PTC Thermistor X
75 Illegal Profile Sel. X
76 Power Unit Set-up X
77 Reduced power mode X 14-59 Actual Number of
Inverter Units
78 Tracking Error (X) (X) 4-34 Tracking Error
Function
79 Illegal PS config X X
80 Drive Initialized to Default Value X
81 CSIV corrupt X
82 CSIV param error X
83 Illegal Option Combination X
84 No Safety Option X
88 Option Detection X
89 Mechanical Brake Sliding X
90 Feedback Monitor (X) (X) 17-61 Feedback Signal
Monitoring
91 Analog input 54 wrong settings X S202
163 ATEX ETR cur.lim.warning X
164 ATEX ETR cur.lim.alarm X
165 ATEX ETR freq.lim.warning X
166 ATEX ETR freq.lim.alarm X
243 Brake IGBT X X X
244 Heatsink temp X X X
245 Heatsink sensor X X
246 Pwr.card supply X
247 Pwr.card temp X X
248 Illegal PS config X
249 Rect. low temp. X
250 New spare parts X

MG33MD22 - VLT® is a registered Danfoss trademark 5-3

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Troubleshooting FC 300 Programming Guide

No. Description Warning Alarm/Trip Alarm/Trip Lock Parameter

Reference
251 New Type Code X X

Table 5.1 Alarm/Warning code list

(X) Dependent on parameter alarm occurs that may cause damage to theAdjustable
1) Cannot be Auto reset via 14-20 Reset Mode frequency drive or connected parts. A trip lock situation
can only be reset by power cycling.
A trip is the action when an alarm has appeared. The trip
will coast the motor and can be reset by pressing the reset
LED indication
5 5 button or make a reset by a digital input (parameter group
5-1* [1]). The original event that caused an alarm cannot
Warning yellow
Alarm flashing red
damage the Adjustable frequency drive or cause
Trip locked yellow and red
dangerous conditions. A trip lock is an action when an

Bit Hex Dec Alarm Word Alarm Word 2 Warning Word Warning Extended
Word 2 Status Word
Alarm Word Extended Status Word
0 00000001 1 Brake Check (A28) ServiceTrip, Read/ Brake Check (W28) reserved Ramping
Write
1 00000002 2 Heatsink temp. ServiceTrip, Heatsink temp. (W29) reserved AMA Running
(A29) (reserved)
2 00000004 4 Ground Fault (A14) ServiceTrip, Ground Fault (W14) reserved Start CW/CCW
Typecode/ NOT start_possible
Sparepart start_possible is
active, when the DI
selections [12] OR
[13] are active and
the requested
direction matches the
reference sign.
3 00000008 8 Ctrl.Card Temp ServiceTrip, Ctrl.Card Temp (W65) reserved Slow-down
(A65) (reserved) slow-down command
active, e.g., via CTW
bit 11 or DI
4 00000010 16 Ctrl. Word TO (A17) ServiceTrip, Ctrl. Word TO (W17) Catch Up
(reserved) catch up command
active, e.g., via CTW
bit 12 or DI
5 00000020 32 Overcurrent (A13) reserved Overcurrent (W13) reserved Feedback High
feedback > p4-57
6 00000040 64 Torque Limit (A12) reserved Torque Limit (W12) reserved Feedback Low
feedback < p4-56
7 00000080 128 Motor Th Over reserved Motor Th Over (W11) reserved Output Current High
(A11) current > p4-51
8 00000100 256 Motor ETR Over reserved Motor ETR Over (W10) reserved Output Current Low
(A10) current < p4-50
9 00000200 512 Inverter Overld. reserved Inverter Overld (W9) reserved Output Freq High
(A9) speed > p4-53
10 00000400 1,024 DC under-volt (A8) reserved DC under-volt (W8) Output Freq Low
speed < p4-52
11 00000800 2,048 DC overvoltage reserved DC overvoltage (W7) Brake Check OK
(A7) brake test NOT ok

5-4 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Troubleshooting FC 300 Programming Guide

Bit Hex Dec Alarm Word Alarm Word 2 Warning Word Warning Extended
Word 2 Status Word
12 00001000 4,096 Short Circuit (A16) reserved DC Voltage Low (W6) reserved Braking Max
BrakePower >
BrakePowerLimit
(p212)
13 00002000 8,192 Soft-charge Fault reserved DC Voltage High (W5) Braking
(A33)
14 00004000 16,384 Line Ph. Loss (A4) reserved Line Ph. Loss (W4) Out of Speed Range
15 00008000 32,768 AMA Not OK reserved No Motor (W3) OVC Active
16 00010000 65,536 Live Zero Error (A2) reserved Live Zero Error (W2) AC Brake 5 5
17 00020000 131,072 Internal Fault (A38) KTY error 10 V Low (W1) KTY Warn Password Timelock
number of allowed
password trials
exceeded - timelock
active
18 00040000 262,144 Brake Overload Fans error Brake Overload (W26) Fans Warn Password Protection
(A26) p0-61 =
ALL_NO_ACCESS OR
BUS_NO_ACCESS OR
BUS_READONLY
19 00080000 524,288 U phase Loss (A30) ECB error Brake Resistor (W25) ECB Warn Reference High
reference > p4-55
20 00100000 1,048,576 V phase Loss (A31) reserved Brake IGBT (W27) reserved Reference Low
reference < p4-54
21 00200000 2,097,152 W phase Loss (A32) reserved Speed Limit (W49) reserved Local Reference
reference site =
REMOTE -> auto on
pressed & active
22 00400000 4,194,304 Serial communi- reserved Serial communication bus reserved Protection Mode
cation bus Fault Fault (W34)
(A34)
23 00800000 8,388,608 24 V Supply Low reserved 24 V Supply Low (W47) reserved Unused
(A47)
24 01000000 16,777,216 Line Failure (A36) reserved Line Failure (W36) reserved Unused
25 02000000 33,554,432 1.8 V Supply Low reserved Current Limit (W59) reserved Unused
(A48)
26 04000000 67,108,864 Brake Resistor (A25) reserved Low Temp (W66) reserved Unused
27 08000000 134,217,728 Brake IGBT (A27) reserved Voltage Limit (W64) reserved Unused
28 10,000,000 268,435,456 Option Change reserved Encoder loss (W90) reserved Unused
(A67)
29 20,000,000 536,870,912 Drive Initialized Feedback Fault Feedback Fault (W61, Unused
(A80) (A61, A90) W90)
30 40,000,000 1,073,741,824 Safe Stop (A68) PTC 1 Safe Stop Safe Stop (W68) PTC 1 Safe Unused
(A71) Stop (W71)
31 80,000,000 2,147,483,648 Mech. brake low Dangerous Failure Extended Status Word Unused
(A63) (A72)

Table 5.2 Description of Alarm Word, Warning Word and Extended Status Word

The alarm words, warning words and extended status words can be read out via serial bus or optional serial communication
bus for diagnosis. See also 16-94 Ext. Status Word.

MG33MD22 - VLT® is a registered Danfoss trademark 5-5

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Troubleshooting FC 300 Programming Guide

WARNING 1, 10 Volts low WARNING/ALARM 7, DC overvoltage

The control card voltage is below 10 V from terminal 50. If the intermediate circuit voltage exceeds the limit, the
Remove some of the load from terminal 50, as the 10 V Adjustable frequency drive trips after a time.
supply is overloaded. Max. 15 mA or minimum 590Ω. Troubleshooting
This condition can be caused by a short in a connected Connect a brake resistor
potentiometer or improper wiring of the potentiometer. Extend the ramp time
Troubleshooting: Remove the wiring from terminal 50. If Change the ramp type
the warning clears, the problem is with the customer
wiring. If the warning does not clear, replace the control Activate the functions in 2-10 Brake Function

5 5 card.
WARNING/ALARM 2, Live zero error
Increase 14-26 Trip Delay at Inverter Fault
WARNING/ALARM 8, DC undervoltage
This warning or alarm will only appear if programmed by If the intermediate circuit voltage (DC link) drops below
the user in 6-01 Live Zero Timeout Function. The signal on the under voltage limit, the Adjustable frequency drive
one of the analog inputs is less than 50% of the minimum checks if a 24V DC backup supply is connected. If no 24V
value programmed for that input. This condition can be DC backup supply is connected, the Adjustable frequency
caused by broken wiring or faulty device sending the drive trips after a fixed time delay. The time delay varies
signal. with unit size.
Troubleshooting Troubleshooting:
Check connections on all the analog input Check that the supply voltage matches the
terminals. Control card terminals 53 and 54 for Adjustable frequency drive voltage.
signals, terminal 55 common. MCB 101 terminals
Perform input voltage test
11 and 12 for signals, terminal 10 common. MCB
109 terminals 1, 3, 5 for signals, terminals 2, 4, 6 Perform soft charge circuit test
common). WARNING/ALARM 9, Inverter overload
Check that the Adjustable frequency drive The Adjustable frequency drive is about to cut out because
programming and switch settings match the of an overload (too high current for too long). The counter
analog signal type. for electronic, thermal inverter protection gives a warning
at 98% and trips at 100%, while giving an alarm. The
Perform Input Terminal Signal Test.
Adjustable frequency drive cannot be reset until the
WARNING/ALARM 3, No motor counter is below 90%.
No motor has been connected to the output of the The fault is that the Adjustable frequency drive is
Adjustable frequency drive. overloaded by more than 100% for too long.
WARNING/ALARM 4, Mains phase loss Troubleshooting
A phase is missing on the supply side, or the line voltage Compare the output current shown on the LCP
imbalance is too high. This message also appears for a with the Adjustable frequency drive rated current.
fault in the input rectifier on the Adjustable frequency
Compare the output current shown on the LCP
drive. Options are programmed at 14-12 Function at Mains
with measured motor current.
Imbalance.
Display the Thermal Drive Load on the LCP and
Troubleshooting: Check the supply voltage and supply
monitor the value. When running above the
currents to the Adjustable frequency drive.
Adjustable frequency drive continuous current
WARNING 5, DC link voltage high rating, the counter should increase. When
The intermediate circuit voltage (DC) is higher than the running below the Adjustable frequency drive
high voltage warning limit. The limit is dependent on the continuous current rating, the counter should
Adjustable frequency drive voltage rating. The unit is still decrease.
active.
See the derating section in the Design Guide for more
WARNING 6, DC link voltage low details if a high switching frequency is required.
The intermediate circuit voltage (DC) is lower than the low
WARNING/ALARM 10, Motor overload temperature
voltage warning limit. The limit is dependent on the
According to the electronic thermal protection (ETR), the
Adjustable frequency drive voltage rating. The unit is still
motor is too hot. Select whether the Adjustable frequency
active.
drive gives a warning or an alarm when the counter
reaches 100% in 1-90 Motor Thermal Protection. The fault

5-6 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Troubleshooting FC 300 Programming Guide

occurs when the motor is overloaded by more than 100% Check the application for excessive current draw
for too long. on the motor.
Troubleshooting WARNING/ALARM 13, Overcurrent
Check for motor overheating. The inverter peak current limit (approximately 200% of the
rated current) is exceeded. The warning lasts about 1.5
Check if the motor is mechanically overloaded.
secs., then the Adjustable frequency drive trips and issues
Check that the motor current set in 1-24 Motor an alarm. This fault may be caused by shock loading or
Current is correct. fast acceleration with high inertia loads. If extended
Ensure that Motor data in parameters 1-20 mechanical brake control is selected, trip can be reset
through 1-25 are set correctly. externally.

If an external fan is in use, check in 1-91 Motor Troubleshooting: 5 5

External Fan that it is selected.
Running AMA in 1-29 Automatic Motor Adaptation Remove power and check if the motor shaft can
(AMA) may tune the Adjustable frequency drive be turned.
to the motor more accurately and reduce thermal Check that the motor size matches the Adjustable
loading. frequency drive.
WARNING/ALARM 11, Motor thermistor over temp Check parameters 1-20 through 1-25 for correct
The thermistor might be disconnected. Select whether the motor data.
Adjustable frequency drive gives a warning or an alarm in
ALARM 14, Ground fault
1-90 Motor Thermal Protection.
There is current from the output phases to ground, either
Troubleshooting in the cable between the Adjustable frequency drive and
Check for motor overheating. the motor or in the motor itself.
Check if the motor is mechanically overloaded. Troubleshooting:
When using terminal 53 or 54, check that the Remove power to the Adjustable frequency drive
thermistor is connected correctly between either and repair the ground fault.
terminal 53 or 54 (analog voltage input) and Check for ground faults in the motor by
terminal 50 (+10V supply) and that the terminal measuring the resistance to ground of the motor
switch for 53 or 54 is set for voltage. Check leads and the motor with a megohmmeter.
1-93 Thermistor Source selects terminal 53 or 54.
ALARM 15, Hardware mismatch
When using digital inputs 18 or 19, check that A fitted option is not operational with the present control
the thermistor is connected correctly between board hardware or software.
either terminal 18 or 19 (digital input PNP only)
Record the value of the following parameters and contact
and terminal 50. Check 1-93 Thermistor Source
your Danfoss supplier:
selects terminal 18 or 19.
15-40 FC Type
WARNING/ALARM 12, Torque limit 15-41 Power Section
The torque has exceeded the value in 4-16 Torque Limit 15-42 Voltage
Motor Mode or the value in 4-17 Torque Limit Generator
Mode. 14-25 Trip Delay at Torque Limit can change this from 15-43 Software Version
a warning only condition to a warning followed by an 15-45 Actual Typecode String
alarm.
15-49 SW ID Control Card
Troubleshooting
15-50 SW ID Power Card
If the motor torque limit is exceeded during
ramp-up, extend the ramp-up time. 15-60 Option Mounted

If the generator torque limit is exceeded during 15-61 Option SW Version (for each option slot)
ramp-down, extend the ramp--down time. ALARM 16, Short circuit
If torque limit occurs while running, possibly There is short-circuiting in the motor or motor wiring.
increase the torque limit. Be sure the system can Remove power to the Adjustable frequency drive and
operate safely at a higher torque. repair the short circuit.

MG33MD22 - VLT® is a registered Danfoss trademark 5-7

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Troubleshooting FC 300 Programming Guide

WARNING/ALARM 17, Control word timeout Check the sensors on the heatsink and control
There is no communication to the Adjustable frequency card.
drive. WARNING 25, Brake resistor short circuit
The warning will only be active when 8-04 Control Word The brake resistor is monitored during operation. If a short
Timeout Function is NOT set to OFF. circuit occurs, the brake function is disabled and the
If 8-04 Control Word Timeout Function is set to Stop and warning appears. The Adjustable frequency drive is still
Trip, a warning appears and the Adjustable frequency drive operational but without the brake function. Remove power
ramps down until it stops then displays an alarm. to the Adjustable frequency drive and replace the brake
Troubleshooting: resistor (see 2-15 Brake Check).
Check connections on the serial communication
5 5 cable.
WARNING/ALARM 26, Brake resistor power limit
The power transmitted to the brake resistor is calculated as
Increase 8-03 Control Word Timeout Time a mean value over the last 120 seconds of run time. The
calculation is based on the intermediate circuit voltage and
Check the operation of the communication
the brake resistance value set in 2-16 AC brake Max.
equipment.
Current. The warning is active when the dissipated braking
Verify a proper installation based on EMC is higher than 90% of the brake resistance power. If Trip [2]
requirements. is selected in 2-13 Brake Power Monitoring, the Adjustable
WARNING/ALARM 20, Temp. input error frequency drive will trip when the dissipated braking
The temperature sensor is not connected. energy reaches 100%.
WARNING/ALARM 21, Parameter error WARNING/ALARM 27, Brake chopper fault
The parameter is out of range. The parameter number is The brake transistor is monitored during operation and if a
reported in the LCP. The affected parameter must be set to short circuit occurs, the brake function is disabled and a
a valid value. warning is issued. The Adjustable frequency drive is still
operational but, since the brake transistor has short-
WARNING/ALARM 22, Hoist mechanical brake
circuited, substantial power is transmitted to the brake
Report value will show what kind it is. 0 = The torque ref.
resistor, even if it is inactive.
was not reached before timeout. 1 = There was no brake
Remove power to the Adjustable frequency drive and
feedback before timeout.
remove the brake resistor.
WARNING 23, Internal fan fault
WARNING/ALARM 28, Brake check failed
The fan warning function is an extra protective function
The brake resistor is not connected or not working.
that checks if the fan is running/mounted. The fan warning
Check 2-15 Brake Check.
can be disabled in 14-53 Fan Monitor ([0] Disabled).
ALARM 29, Heatsink temp
For the D, E, and F Frame filters, the regulated voltage to
The maximum temperature of the heatsink has been
the fans is monitored.
exceeded. The temperature fault will not reset until the
Troubleshooting: temperature falls below a defined heatsink temperature.
Check for proper fan operation. The trip and reset points are different based on the
Cycle power to the Adjustable frequency drive Adjustable frequency drive power size.
and make sure that the fan operates briefly at Troubleshooting:
start-up. Check for the following conditions.
Check the sensors on the heatsink and control Ambient temperature too high.
card. Motor cable too long.
WARNING 24, External fan fault Incorrect airflow clearance above and below the
The fan warning function is an extra protective function Adjustable frequency drive
that checks if the fan is running/mounted. The fan warning
Blocked airflow around the Adjustable frequency
can be disabled in 14-53 Fan Monitor ([0] Disabled).
drive.
Troubleshooting:
Damaged heatsink fan.
Check for proper fan operation.
Dirty heatsink.
Cycle power to the Adjustable frequency drive
and make sure that the fan operates briefly at ALARM 30, Motor phase U missing
start-up. Motor phase U between the Adjustable frequency drive
and the motor is missing.

5-8 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Troubleshooting FC 300 Programming Guide

Remove power from the Adjustable frequency drive and No. Text
check motor phase U. 1024-1284 Internal fault. Contact your Danfoss supplier or the
ALARM 31, Motor phase V missing Danfoss Service Department.
Motor phase V between the Adjustable frequency drive 1299 Option SW in slot A is too old
and the motor is missing. 1300 Option SW in slot B is too old
1302 Option SW in slot C1 is too old
Remove power from the Adjustable frequency drive and
1315 Option SW in slot A is not supported (not allowed)
check motor phase V.
1316 Option SW in slot B is not supported (not allowed)
ALARM 32, Motor phase W missing 1318 Option SW in slot C1 is not supported (not
Motor phase W between the Adjustable frequency drive allowed)
and the motor is missing. 1379-2819 Internal fault. Contact yourDanfoss supplier or 5 5
Remove power from the Adjustable frequency drive and DanfossService Department.
check motor phase W. 2820 LCP stack overflow

ALARM 33, Inrush fault 2821 Serial port overflow

Too many power-ups have occurred within a short time 2822 USB port overflow
period. Let the unit cool to operating temperature. 3072-5122 Parameter value is outside its limits
5123 Option in slot A: Hardware incompatible with
WARNING/ALARM 34, communication fault
control board hardware
The serial communication bus on the communication
5124 Option in slot B: Hardware incompatible with
option card is not working.
control board hardware
WARNING/ALARM 35, Option fault 5125 Option in slot C0: Hardware incompatible with
An option alarm is received. The alarm is option specific. control board hardware
The most likely cause is a power-up or a communication 5126 Option in slot C1: Hardware incompatible with
fault. control board hardware
WARNING/ALARM 36, Mains failure 5376-6231 Internal fault. Contact yourDanfoss supplier or
This warning/alarm is only active if the supply voltage to DanfossService Department.
the Adjustable frequency drive is lost and 14-10 Mains
Failure is NOT set to [0] No Function. Check the fuses to the ALARM 39, Heatsink sensor
Adjustable frequency drive and line power supply to the No feedback from the heatsink temperature sensor.
unit.
The signal from the IGBT thermal sensor is not available on
ALARM 37, Imb of sup volt the power card. The problem could be on the power card,
There is a current imbalance between the power units on the gate drive card, or the ribbon cable between the
ALARM 38, Internal fault power card and gate drive card.
When an internal fault occurs, a code number defined in WARNING 40, Overload of digital output terminal 27
the table below is displayed. Check the load connected to terminal 27 or remove short-
Troubleshooting circuit connection. Check 5-00 Digital I/O Mode and
Cycle power 5-01 Terminal 27 Mode.
Check that the option is properly installed WARNING 41, Overload of digital output terminal 29
Check the load connected to terminal 29 or remove short-
Check for loose or missing wiring
circuit connection. Check 5-00 Digital I/O Mode and
It may be necessary to contact your Danfoss supplier or 5-02 Terminal 29 Mode.
service department. Note the code number for further
WARNING 42, Overload of digital output on X30/6 or
troubleshooting directions.
overload of digital output on X30/7
No. Text For X30/6, check the load connected to X30/6 or remove
0 Serial port cannot be initialized. Contact short-circuit connection. Check 5-32 Term X30/6 Digi Out
yourDanfoss supplier or DanfossService (MCB 101).
Department. For X30/7, check the load connected to X30/7 or remove
256-258 Power EEPROM data is defect or too old short-circuit connection. Check 5-33 Term X30/7 Digi Out
512-519 Internal fault. Contact yourDanfoss supplier or (MCB 101).
Danfoss Service Department.
783 Parameter value outside of min/max limits

MG33MD22 - VLT® is a registered Danfoss trademark 5-9

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Troubleshooting FC 300 Programming Guide

ALARM 43, Ext. supply ALARM 51, AMA check Unom and Inom
MCB 113 Ext. Relay Option is mounted without ext. 24 V The settings for motor voltage, motor current, and motor
DC. Either connect an ext. 24 V DC supply or specify that power are wrong. Check the settings in parameters 1-20 to
no external supply is used via 14-80 Option Supplied by 1-25.
External 24VDC [0]. A change in 14-80 Option Supplied by
ALARM 52, AMA low Inom
External 24VDC requires a power cycle.
The motor current is too low. Check the setting in
ALARM 45, Earth Fault 2 4-18 Current Limit.
Ground fault on start-up.
ALARM 53, AMA motor too big
Troubleshooting The motor is too big for the AMA to operate.

5 5 Check for proper grounding and loose

connections.
ALARM 54, AMA motor too small
The motor is too small for the AMA to operate.
Check for proper wire size.
ALARM 55, AMA Parameter out of range
Check motor cables for short-circuits or leakage The parameter values of the motor are outside of the
currents. acceptable range. AMA will not run.
ALARM 46, Power card supply ALARM 56, AMA interrupted by user
The supply on the power card is out of range. The AMA has been interrupted by the user.
There are three power supplies generated by the switch ALARM 57, AMA timeout
mode power supply (SMPS) on the power card: 24V, 5V, Try to restart AMA again. Repeated restarts may overheat
+/- 18V. When powered with 24V DC with the MCB 107 the motor.
option, only the 24V and 5V supplies are monitored. When
ALARM 58, AMA internal fault
powered with three-phase AC line voltage, all three
Contact your Danfoss supplier.
supplied are monitored.
WARNING 59, Current limit
Troubleshooting
The current is higher than the value in 4-18 Current Limit.
Check for a defective power card.
Ensure that Motor data in parameters 1-20 through 1-25
Check for a defective control card. are set correctly. Possibly increase the current limit. Be sure
Check for a defective option card. the system can operate safely at a higher limit.

If a 24V DC power supply is used, verify proper WARNING 60, External interlock
supply power. A digital input signal is indicating a fault condition external
to the Adjustable frequency drive. An external interlock has
WARNING 47, 24V supply low commanded the Adjustable frequency drive to trip. Clear
The 24 V DC is measured on the control card. The external the external fault condition. To resume normal operation,
24V DC backup power supply may be overloaded; apply 24V DC to the terminal programmed for external
otherwise, contact your Danfoss supplier. interlock. Reset the Adjustable frequency drive.
WARNING 48, 1.8V supply low WARNING/ALARM 61, Tracking error
The 1.8V DC supply used on the control card is outside of An error between calculated speed and speed
allowable limits. The power supply is measured on the measurement from feedback device. The function Warning/
control card. Check for a defective control card. If an Alarm/Disabling setting is in 4-30 Motor Feedback Loss
option card is present, check for an overvoltage condition. Function. Accepted error setting in 4-31 Motor Feedback
WARNING 49, Speed limit Speed Error and the allowed time the error occur setting in
When the speed is not within the specified range in 4-32 Motor Feedback Loss Timeout. During a commissioning
4-11 Motor Speed Low Limit [RPM] and 4-13 Motor Speed procedure the function may be effective.
High Limit [RPM], the Adjustable frequency drive will show WARNING 62, Output frequency at maximum limit
a warning. When the speed is below the specified limit in The output frequency has reached the value set in
1-86 Trip Speed Low [RPM] (except when starting or 4-19 Max Output Frequency. Check the application to
stopping) the Adjustable frequency drive will trip. determine the cause. Possibly increase the output
ALARM 50, AMA calibration failed frequency limit. Be sure the system can operate safely at a
Contact your Danfoss supplier or Danfoss Service higher output frequency. The warning will clear when the
Department. output drops below the maximum limit.

5-10 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Troubleshooting FC 300 Programming Guide

ALARM 63, Mechanical brake low reset signal must be is be sent (via Bus, Digital I/O, or by
The actual motor current has not exceeded the “release pressing [RESET]).
brake” current within the “Start delay” time window. ALARM 72, Dangerous failure
WARNING/ALARM 65, Control card over temperature Safe Stop with Trip Lock. The dangerous failure alarm is
The cutout temperature of the control card is 176°F [80°C]. issued if the combination of safe stop commands is
unexpected. This is the case if the VLT enables X44/10 but
Troubleshooting
safe stop is somehow not enabled. Furthermore, if the is
• Check that the ambient operating temperature is the only device using safe stop (specified through
within limits.
selection [4] or [5] in 5-19 Terminal 37 Safe Stop), an
• Check for clogged filters. unexpected combination is activation of safe stop without
• Check fan operation. the X44/10 being activated. The following table 5 5
summarizes the unexpected combinations that lead to
• Check the control card.
Alarm 72. Note that if X44/10 is activated in selection 2 or
WARNING 66, Heatsink temperature low 3, this signal is ignored! However, the will still be able to
The Adjustable frequency drive is too cold to operate. This activate Safe Stop.
warning is based on the temperature sensor in the IGBT
WARNING 73, Safe stop auto restart
module.
Safe stopped. Note that with automatic restart enabled,
Increase the ambient temperature of the unit. Also, a
the motor may start when the fault is cleared.
trickle amount of current can be supplied to the
Adjustable frequency drive whenever the motor is stopped ALARM 74, PTC Thermistor
by setting 2-00 DC Hold/Preheat Current at 5% and Alarm related to the ATEX option. The PTC is not working.
1-80 Function at Stop ALARM 75, Illegal profile sel.
ALARM 67, Option module configuration has changed Parameter value must not be written while motor is
One or more options have either been added or removed running. Stop motor before writing MCO profile to
since the last power-down. Check that the configuration 8-10 Control Word Profile for instance.
change is intentional and reset the unit. WARNING 76, Power unit set-up
ALARM 68, Safe stop activated The required number of power units does not match the
Loss of the 24V DC signal on terminal 37 has caused the detected number of active power units.
filter to trip. To resume normal operation, apply 24V DC to Troubleshooting:
terminal 37 and reset the filter. When replacing an F-frame module, this will occur if the
ALARM 69, Power card temperaturePower card power specific data in the module power card does not
temperature match the rest of the Adjustable frequency drive. Please
The temperature sensor on the power card is either too confirm the spare part and its power card are the correct
hot or too cold. part number.

Troubleshooting 77 WARNING, Reduced power mode

Check that the ambient operating temperature is This warning indicates that the Adjustable frequency drive
within limits. is operating in reduced power mode (i.e., less than the
allowed number of inverter sections). This warning will be
Check for clogged filters.
generated on power cycle when the Adjustable frequency
Check fan operation. drive is set to run with fewer inverters and will remain on.
Check the power card. ALARM 78, Tracking error
ALARM 70, Illegal FC configuration The difference between setpoint value and actual value
The control card and power card are incompatible. Contact has exceeded the value in 4-35 Tracking Error. Disable the
your supplier with the type code of the unit from the function by 4-34 Tracking Error Function or select an alarm/
nameplate and the part numbers of the cards to check warning also in 4-34 Tracking Error Function. Investigate the
compatibility. mechanics around the load and motor. Check feedback
connections from motor – encoder – to Adjustable
ALARM 71, PTC 1 safe stop frequency drive. Select motor feedback function in
Safe Stop has been activated from the PTC Thermistor 4-30 Motor Feedback Loss Function. Adjust tracking error
Card (motor too warm). Normal operation can be resumed band in 4-35 Tracking Error and 4-37 Tracking Error
when the applies 24 V DC to T-37 again (when the motor Ramping.
temperature reaches an acceptable level) and when the
digital Input from the is deactivated. When that happens, a

MG33MD22 - VLT® is a registered Danfoss trademark 5-11

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Troubleshooting FC 300 Programming Guide

ALARM 79, Illegal power section configuration ALARM 94, End of curve
The scaling card is the incorrect part number or not Feedback is lower than the setpoint. This may indicate
installed. Also MK102 connector on the power card could leakage in the system. 22-50 End of Curve Function is set for
not be installed. alarm. Troubleshoot the system and reset the Adjustable
ALARM 80, Unit initialized to default value frequency drive after the fault has been cleared.
Parameter settings are initialized to default settings after a ALARM 95, Broken belt
manual reset. Reset the unit to clear the alarm. Torque is below the torque level set for no load, indicating
ALARM 81, CSIV corrupt a broken belt. 22-60 Broken Belt Function is set for alarm.
CSIV file has syntax errors. Troubleshoot the system and reset the Adjustable
frequency drive after the fault has been cleared.
5 5 ALARM 82, CSIV par. err.
CSIV failed to init a parameter. ALARM 96, Start delayed
Motor start has been delayed due to short-cycle
ALARM 83, Illegal option combination protection. 22-76 Interval between Starts is enabled.
The mounted options are not supported to work together. Troubleshoot the system and reset the Adjustable
ALARM 84, No safety option frequency drive after the fault has been cleared.
The safety option was removed without applying a general WARNING 97, Stop delayed
reset. Reconnect the safety option. Stopping the motor has been delayed due to short cycle
ALARM 88, Option detection protection. 22-76 Interval between Starts is enabled.
A change in the option layout has been detected. This Troubleshoot the system and reset the Adjustable
alarm occurs when 14-89 Option Detection is set to [0] frequency drive after the fault has been cleared.
Frozen configuration and the option layout for some reason WARNING 98, Clock fault
has changed. An option layout change has to be enabled Time is not set or the RTC clock has failed. Reset the clock
in 14-89 Option Detection before the change is accepted. If in 0-70 Date and Time.
the change of configuration is not accepted, it is only
possible to reset Alarm 88 (Trip-lock) when the option WARNING 163, ATEX ETR cur.lim.warning
configuration has been re-established/corrected. The warning limit of ATEX ETR rated current curve has
been reached. The warning is activated at 83% and de-
WARNING 89, Mechanical brake sliding activated at 65% of the permitted thermal overload.
The hoist brake monitor has detected a motor speed >
10rpm. ALARM 164, ATEX ETR cur.lim.alarm
The ATEX ETR permitted thermal overload has been
ALARM 90, Feedback mon. exceeded.
Check the connection to encoder/ resolver option and
eventually replace the MCB 102 or MCB 103. WARNING 165, ATEX ETR freq.lim.warning
The Adjustable frequency drive is running more than 50
ALARM 91, Analogue input 54 wrong settings sec. below the permitted minimum frequency (1-98 ATEX
Switch S202 has to be set in position OFF (voltage input) ETR interpol. points freq. [0]).
when a KTY sensor is connected to analog input terminal
54. ALARM 166, ATEX ETR freq.lim.alarm
The Adjustable frequency drive has operated more than 60
ALARM 92, No flow sec. (in a period of 600 sec.) below the permitted
A no-flow condition has been detected in the system. minimum frequency (1-98 ATEX ETR interpol. points freq. [0]).
22-23 No-Flow Function is set for alarm. Troubleshoot the
system and reset the Adjustable frequency drive after the ALARM 243, Brake IGBT
fault has been cleared. This alarm is only for F Frame drives. It is equivalent to
Alarm 27. The report value in the alarm log indicates
ALARM 93, Dry pump which power module generated the alarm:
A no-flow condition in the system with the Adjustable
frequency drive operating at high speed may indicate a ALARM 244, Heatsink temperature
dry pump. 22-26 Dry Pump Function is set for alarm. This alarm is only for F Frame adjustable frequency drives.
Troubleshoot the system and reset the Adjustable It is equivalent to Alarm 29. The report value in the alarm
frequency drive after the fault has been cleared. log indicates which power module generated the alarm.
ALARM 245, Heatsink sensor
This alarm is only for F Frame adjustable frequency drives.
It is equivalent to Alarm 39. The report value in the alarm
log indicates which power module generated the alarm.

5-12 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Troubleshooting FC 300 Programming Guide

1 = left most inverter module. WARNING 249, Rect. low temperature

IGBT sensor fault (highpower units only).
2 = middle inverter module in F2 or F4
Adjustable frequency drive. WARNING 250, New spare part
A component in the Adjustable frequency drive has been
2 = right inverter module in F1 or F3 Adjustable
replaced. Reset the Adjustable frequency drive for normal
frequency drivee.
operation.
3 = right inverter module in F2 or F4 Adjustable
WARNING 251, New type code
frequency drive.
The power card or other components have been replaced
5 = rectifier module. and the type code changed. Reset to remove the warning
ALARM 246, Power card supply
This alarm is only for F Frame Adjustable frequency drive.
and resume normal operation.
5 5
It is equivalent to Alarm 46. The report value in the alarm
log indicates which power module generated the alarm.
1 = left most inverter module.
2 = middle inverter module in F2 or F4
Adjustable frequency drive.
2 = right inverter module in F1 or F3 Adjustable
frequency drive.
3 = right inverter module in F2 or F4 Adjustable
frequency drive.
5 = rectifier module.
ALARM 69, Power card temperaturePower card
temperature
This alarm is only for F Frame Adjustable frequency drive.
It is equivalent to Alarm 69. The report value in the alarm
log indicates which power module generated the alarm.
1 = left most inverter module.
2 = middle inverter module in F2 or F4
Adjustable frequency drive.
2 = right inverter module in F1 or F3 Adjustable
frequency drive.
3 = right inverter module in F2 or F4 Adjustable
frequency drive.
5 = rectifier module.
ALARM 248, Illegal power section configuration
This alarm is only for F Frame adjustable frequency drives.
It is equivalent to Alarm 79. The report value in the alarm
log indicates which power module generated the alarm:
1 = left most inverter module.
2 = middle inverter module in F2 or F4
Adjustable frequency drive.
2 = right inverter module in F1 or F3 Adjustable
frequency drive.
3 = right inverter module in F2 or F4 Adjustable
frequency drive.
5 = rectifier module.

MG33MD22 - VLT® is a registered Danfoss trademark 5-13

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Troubleshooting FC 300 Programming Guide

5 5

5-14 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Index FC 300 Programming Guide

Index
E
Electrical Terminals............................................................................. 0-6
A
Abbreviations....................................................................................... 0-1 Encoder Pulses................................................................................... 2-67

Alarm Environment.................................................................................... 2-133

Log.................................................................................................. 2-138 Ethernet................................................................................ 2-105, 2-108
Messages........................................................................................... 4-1
EtherNet/IP....................................................................................... 2-107
Word................................................................................................. 2-85
ETR....................................................................................................... 2-142
Analog Inputs............................................................................... 0-2, 4-6

B F
Feedback..................................................................................... 4-9, 4-12
Braking
Braking............................................................................................... 4-8 Forward Open................................................................................. 2-107
Energy................................................................................................. 0-3 Freeze Output...................................................................................... 0-2
Break-away Torque............................................................................. 0-2 Fuses........................................................................................................ 4-9
Bus Controlled................................................................................... 2-67

G
C Graphical Display................................................................................ 1-1
Cabling............................................................................................... 2-108
Catch Up.............................................................................................. 2-51
H
Change-Of-State............................................................................. 2-107 Historic Log...................................................................................... 2-137
Changing
A Group Of Numeric Data Values............................................. 1-8
A Text Value...................................................................................... 1-8 I
Data..................................................................................................... 1-8 IGMP.................................................................................................... 2-108
Clockwise............................................................................................. 2-21 Incremental Encoder..................................................................... 2-143
Coasting......................................................................................... 0-2, 1-3 Indexed Parameters........................................................................... 1-9
Communication Option.................................................................... 4-9 Infinitely Variable Change Of Numeric Data Value................. 1-9
Configuration....................................................................... 2-84, 2-106 Initialization........................................................................................... 1-1
Control Cables...................................................................................... 0-7 Input Terminals.................................................................................... 4-6
Cooling................................................................................................. 2-26
Current Rating...................................................................................... 4-6 J
Jog............................................................................................................ 0-2

D
Data Log Settings........................................................................... 2-136 L
DC Link.................................................................................................... 4-6 Language
Package 1.......................................................................................... 2-2
Default Settings................................................................................... 1-1 Package 2.......................................................................................... 2-2
Definitions............................................................................................. 0-2 Package 3.......................................................................................... 2-2
Package 4.......................................................................................... 2-2
Derating.................................................................................................. 4-6
LCP............................................................................................................ 1-1
DeviceNet......................................................................................... 2-101
LEDs................................................................................................. 1-1, 1-2
Digital Input.......................................................................................... 4-7
Line Power Supply.............................................................................. 0-4
Display
Mode................................................................................................... 1-4 Local
Mode - Selection Of Readouts................................................... 1-4 Control Keys..................................................................................... 1-1
Reference........................................................................................... 2-3
Drive Identification........................................................................ 2-139

MG33MD22 - VLT® is a registered Danfoss trademark 6-1

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 Index FC 300 Programming Guide

Reference.......................................................................................... 2-107
M Relay Outputs..................................................................................... 2-54
Main Reset..................................................................................... 4-6, 4-12, 1-3
Menu................................................................................................... 1-5
Menu Mode.............................................................................. 1-2, 1-8
Reactance........................................................................................ 2-16 S
MCB Safety Precautions.............................................................................. 0-4
113.................................................................... 2-54, 2-59, 2-75, 2-76 Serial Communication....................................................................... 0-2
114.................................................................................................. 2-154
Shielded/armored............................................................................... 0-7
Motor
Current.................................................................................... 4-6, 4-10 Speed Up/Down.................................................................................. 0-8
Data.......................................................................................... 4-7, 4-10 Start
Power............................................................................................... 4-10 Delay................................................................................................. 2-21
Protection....................................................................................... 2-24 Function.......................................................................................... 2-21
Status............................................................................................. 2-141
Start/Stop............................................................................................... 0-7
Multicast............................................................................................ 2-108
Stator Leakage Reactance............................................................. 2-16
Status
N Status.................................................................................................. 1-2
Network.................................................................. 2-105, 2-107, 2-108 Messages........................................................................................... 1-1
Numerical Local Control Panel....................................................... 1-9 Step-by-Step......................................................................................... 1-9
Supply Voltage..................................................................................... 4-9

O Switching Frequency......................................................................... 4-6

Operating Mode.................................................................................. 2-3 Symbols.................................................................................................. 0-1
Option Ident..................................................................................... 2-139 Synchronous Motor Speed.............................................................. 0-2
Output
Current............................................................................................... 4-6
Speed................................................................................................ 2-21 T
Terminal
X45/1 Output Min Scale, 6-71.................................................. 2-76
P X45/3 Output Min Scale, 6-81.................................................. 2-77
Parameter Thermal Load................................................................................... 2-142
Access............................................................................................ 2-104
Thermistor.................................................................................. 2-24, 0-4
Info.................................................................................................. 2-140
Selection............................................................................................ 1-8 Thrmstr................................................................................................... 4-7
Set-up................................................................................................. 1-5 Trip Reset.......................................................................................... 2-129
Password.............................................................................................. 2-11
Potentiometer Reference................................................................. 0-8
V
Programming....................................................................................... 4-6 Value........................................................................................................ 1-9
Protection Mode.................................................................................. 0-5 Voltage Reference Via A Potentiometer..................................... 0-8
Pulse Start/Stop................................................................................... 0-8 VVCplus................................................................................................... 0-4

Q W
Quick Warning Word.................................................................................... 2-85
Menu........................................................................................... 1-2, 1-5
Warnings................................................................................................ 4-1
Menu Mode.............................................................................. 1-2, 1-5
Transfer Of Parameter Settings Between Multiple Adjusta-
ble Frequency Drives...... 1-3

R
Rated Motor Speed............................................................................ 0-2
RCD........................................................................................................... 0-3

6-2 MG33MD22 - VLT® is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx
 www.danfoss.com/drives

130R0334 MG33MD22 Rev. 2011-10-24

*MG33MD22*

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20849-Danfoss-131B0312-VLT-Automation-VT-Drive-VFD-FC302-230V-3-HP.aspx