Professional Documents
Culture Documents
Actuator Specs
Actuator Specs
The actuators and controls are sized in accordance with the following supply conditions:
Pneumatic actuators shall be operated by instrument air at the following pressure range.
• minimum 4,2 barg (actuator sizing)
• maximum 5,72 barg
• design 12 barg (actuator pressure retain parts can withstand a pick pressure of
14 barg for 1 hour)
Pneumatic Actuators are sized based on safety factor of 1.5 times the maximum torque
from the valves.
Pneumatic spring return actuator based on the scotch yoke mechanism especially designed to
provide an output torque curve which covers the most common quarter turn valve torque
requirement along the full 90° stroke.
SKETCH 2 : SDV (Single acting actuators with SDV tags) - Sketch 2 drawing n. GKT-300-
IN-2580-1920001-002, rev 02A:
• n. 1 off air filter reducer in stainless steel complete with pressure gauge in stainless steel;
• n. 1 off isolation valve in stainless steel;
• n. 1 off check valve in stainless steel;
• n. 1 off safety relief valve in stainless steel;
• n. 2 off (n. 3 off solenoid valve for tag 29-SDV-101 only, as requested in TC4) 3/2 spring return
solenoid valve in stainless steel, explosion proof, 24 VDC (Asco make solenoid valve with coil
rating of 4W, Maxseal make solenoid valve with coil rating of 3W);
• n. 1 off 3/2 pneumatic valve spring return in stainless steel (only when necessary for achieved
the required flow rate),
• n. 1 off uni-directional flow regulator in stainless steel for regulation of stroking time in opening;
• n. 1 off check valve in stainless steel (for close loop);
• n. 1 off bi-directional flow regulator in stainless steel for regulation of stroking time in closing (for
close loop);
• n. 1 off quick exhaust valve in stainless steel (for close loop);
• n. 1 off Hart position transmitter described in section 5.3;
• Tubing in Duplex material, Metric size;
• Compression fittings in stainless steel, Swagelock make.
SKETCH 4 : ROV (Single acting actuators with ROV tags) - Sketch 4 drawing n. GKT-300-
IN-2580-1920001-004, rev 02A:
• n. 1 off air filter reducer in stainless steel complete with pressure gauge in stainless steel;
• n. 1 off isolation valve in stainless steel;
• n. 1 off check valve in stainless steel;
• n. 1 off safety relief valve in stainless steel;
• n. 1 off 3/2 spring return solenoid valve in stainless steel, explosion proof, 24 VDC (Maxseal
make solenoid valve with coil rating of 3W);
• n. 1 off 3/2 pneumatic valve spring return in stainless steel (only when necessary for achieve
the required flow rate),
• n. 1 off uni-directional flow regulator in stainless steel for regulation of stroking time in opening;
• n. 1 off check valve in stainless steel (for close loop);
• n. 1 off bi-directional flow regulator in stainless steel for regulation of stroking time in closing (for
close loop);
• n. 1 off quick exhaust valve in stainless steel (for close loop);
• n. 1 off FF position transmitter described in section 5.3;
• Tubing in Duplex material, Metric size;
• Compression fittings in stainless steel, Swagelock make.
SKETCH 6 (Single acting actuators with BDV tags) - Sketch 6 drawing n. GKT-300-
IN-2580-1920001-006, rev 02:
• n. 1 off air filter reducer in stainless steel complete with pressure gauge in stainless steel;
• n. 1 off safety relief valve in stainless steel;
• n. 1 off isolation valve in stainless steel;
• n. 1 off check valve in stainless steel;
• n. 2 off 3/2 spring return solenoid valve in stainless steel, explosion proof, 24 VDC (Asco make
solenoid valve with coil rating of 4W, Maxseal make solenoid valve with coil rating of 3W);
• n. 1 off 3/2 pneumatic valve spring return in stainless steel (only when necessary for achieve
the required flow rate);
• n. 1 off uni-directional flow regulator in stainless steel for regulation of stroking time in opening;
• n. 1 off check valve in stainless steel (for close loop);
• n. 1 off bi-directional flow regulator in stainless steel for regulation of stroking time in closing (for
close loop);
• n. 1 off quick exhaust valve in stainless steel (for close loop);
• n. 1 off Hart position transmitter described in section 5.3;
• Back up tank described in section 5.1.
• Tubing in Duplex material, Metric size;
Compression fittings in stainless steel, Swagelock make.