CFRP Strips

CFRP Strips
CFRP Strips
Heavy-Duty Carbon Fibre Reinforced Polymer (CFRP) Strips for
Structural Repair & Strengthening
_______________________________________________________________________________
Product Description Heavy-duty strengthening system for reinforced concrete,
masonry, timber etc. consisting of thin CFRP Strips with epoxy
adhesive Chemdur 30.
_______________________________________________________________________________
Advantages CFRP Composite system is used in the following situations:
-- Increased loads in existing structures.
-- Changes in building utilization
-- Addition of Floors
-- Earthquake strengthening
-- Repair & Retrofitting of damaged structures.
-- Compensation for under-reinforcement
_______________________________________________________________________________
Advantages --Lightweight
--Thin cross-section
--Easy to transport (rolls)
--Economical application- no heavy handling and
installation equipment.
-- Very high strength
-- High alkali and fatigue resistance
-- No corrosive
_______________________________________________________________________________
Packaging -- Sizes: S512, S812, S1012 & S1014 available.
-- Supply in rolls of 250 m or cut to size.
_______________________________________________________________________________
Shelf Life Unlimited (no exposure to direct sunshine)
_______________________________________________________________________________
Technical Data
_______________________________________________________________________________
Colour Black
_______________________________________________________________________________
Base Carbon fiber reinforced with an epoxy matrix
_______________________________________________________________________________
Fiber Volumetric content* > 68 %
_______________________________________________________________________________
E-Modulus (mean value) > 165, 000 N/mm2
_______________________________________________________________________________
CFRP Strips
_______________________________________________________________________________
Tensile Strength (min. value) > 2, 800 N/mm2
_______________________________________________________________________________
Mean value of tensile > 3, 050 N/mm2
Strength at break
_______________________________________________________________________________
Elongation at break > approx 1.7 %
_______________________________________________________________________________
Density 1.5 g/cm3
_______________________________________________________________________________
Application
_______________________________________________________________________________
Important notes Mix Chemdur 30 at low speed (max. 500rpm) so that as little air
as possible is being entrained. Work the adhesive well into the
concrete surface.
-- Medium adhesive tensile strength of the prepared concrete
substrate should be 1.5 N/mm2.
-- Max. substrate moisture content 4 %
-- Min. application temp. + 10°C.
-- Ambient and substrate temperature during application
must be min. 5°C.
_______________________________________________________________________________
Substrate Concrete:
Clean surface, free from grease and oil, dry, no loose particles or
laitance. Concrete age, depending on climate, 3 to 4 weeks
minimum.
Surface Preparation:
Grinding, chipping or sand-blasting. Remove all dust & loose
particles by an air blower. The surface to be coated must be
level. Tolerance for 2 m length, max.10 mm.
_______________________________________________________________________________
Application Apply the well-mixed Chemdur 30 adhesive carefully to the
properly prepared substrate with a spatula to form a very thin
layer. Place CFRP Strip on a table and clean it with Colma
Cleaner. Apply Chemdur 30 adhesive with a spatula onto the
CFRP Strip.
Within the open time of the adhesive, depending on temperature,
place strip onto the concrete surface. Using a rubber roller, press
the strip into the epoxy adhesive until the material is forced out
on both sides of the laminate. Remove surplus epoxy adhesive.
_______________________________________________________________________________
CFRP Strips
_______________________________________________________________________________
Adhesive Consumption Approximately 0.50 Kg/m of Chemdur 30 will be used for
CFRP Strip of 80 mm width.
_______________________________________________________________________________
Safety
_______________________________________________________________________________
Safety Precautions Wear protective clothing (gloves, safety glasses). In contact with
eyes rinse immediately with clean warm water and seek medical
attention without delay.
_______________________________________________________________________________
Toxicity Non – toxic.
_______________________________________________________________________________
Transportation Non – hazardous.
_______________________________________________________________________________

CFRP Strips

Uploaded by

Copyright:

Available Formats

CFRP Strips

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CFRP Strips

Uploaded by

Copyright:

Available Formats

CFRP Strips

You might also like