DD4450 Service Manual

Model PD-D1
Machine Code: C279

Field Service Manual
3 February, 2012
Important Safety Notices
Responsibilities of the Customer Engineer
Customer Engineer
Maintenance shall be done only by trained customer engineers who have completed service training for
the machine and all optional devices designed for use with the machine.
Reference Material for Maintenance
• Maintenance shall be done using the special tools and procedures prescribed for maintenance of
the machine described in the reference materials (service manuals, technical bulletins, operating
instructions, and safety guidelines for customer engineers).
• In regard to other safety issues not described in this document, all customer engineers shall strictly
obey procedures and recommendations described the "CE Safety Guide".
• Use only consumable supplies and replacement parts designed for use of the machine.
Before Installation, Maintenance
Shipping and Moving the Machine
• Work carefully when lifting or moving the machine. If the machine is heavy, two or more customer
engineers may be required to prevent injuries (muscle strains, spinal injuries, etc.) or damage to the
machine if it is dropped or tipped over.
• Personnel moving or working around the machine should always wear proper clothing and
footwear. Never wear loose fitting clothing or accessories (neckties, loose sweaters, bracelets,
etc.) or casual footwear (slippers, sandals, etc.) when lifting or moving the machine.
• Always unplug the power cord from the power source before you move the product. Before you
move the product, arrange the power cord so it will not fall under the product.
Power
• Always disconnect the power plug before doing any maintenance procedure. After switching off
the machine, power is still supplied to the main machine and other devices. To prevent electrical
1
shock, switch the machine off, wait for a few seconds, then unplug the machine from the power
source.
• Before you do any checks or adjustments after turning the machine off, work carefully to avoid
injury. After removing covers or opening the machine to do checks or adjustments, never touch
electrical components or moving parts (gears, timing belts, etc.).
• After turning the machine on with any cover removed, keep your hands away from electrical
components and moving parts. Never touch the cover of the fusing unit, gears, timing belts, etc.
Installation, Disassembly and Adjustments
• After installation, maintenance, or adjustment, always check the operation of the machine to make
sure that it is operating normally. This ensures that all shipping materials, protective materials, wires
and tags, metal brackets, etc., removed for installation, have been removed and that no tools
remain inside the machine. This also ensures that all release interlock switches have been restored
to normal operation.
• Never use your fingers to check moving parts causing spurious noise. Never use your fingers to
lubricate moving parts while the machine is operating.
Special Tools
• Use only standard tools approved for machine maintenance.

• For special adjustments, use only the special tools and lubricants described in the service manual.
Using tools incorrectly, or using tools that could damage parts, could damage the machine or
cause injuries.
During Maintenance
General
• Before you begin a maintenance procedure:

• 1) Switch the machine off
• 2) Disconnect the power plug from the power source.
2
Safety Devices
• Never remove any safety device unless it requires replacement. Always replace safety devices
immediately.
• Never do any procedure that defeats the function of any safety device. Modification or removal of
a safety device (fuse, switch, etc.) could lead to a fire and personal injury. Always test the
operation of the machine to ensure that it is operating normally and safely after removal and
replacement of any safety device.
• For replacements use only the correct fuses or circuit breakers rated for use with the machine. Using
replacement devices not designed for use with the machine could lead to a fire and personal
injuries.
Organic Cleaners
• During preventive maintenance, never use any organic cleaners (alcohol, etc.) other than those
described in the service manual.
• Make sure the room is well ventilated before using any organic cleaner. Use organic solvents in
small amounts to avoid breathing the fumes and becoming nauseous.
• Switch the machine off, unplug it, and allow it to cool before doing preventive maintenance. To
avoid fire or explosion, never use an organic cleaner near any part that generates heat.
• Wash your hands thoroughly after cleaning parts with an organic cleaner to contamination of
food, drinks, etc. which could cause illness.
• Clean the floor completely after accidental spillage of silicone oil or other materials to prevent
slippery surfaces that could cause accidents leading to hand or leg injuries. Use dry rags to soak
up spills.
Power Plug and Power Cord
• Before serving the machine (especially when responding to a service call), always make sure that
the power plug has been inserted completely into the power source. A partially inserted plug could
lead to heat generation (due to a power surge caused by high resistance) and cause a fire or other
problems.
• Always check the power plug and make sure that it is free of dust and lint. Clean it if necessary. A
dirty plug can generate heat which could cause a fire.
3
• Inspect the length of the power cord for cuts or other damage. Replace the power cord if
necessary. A frayed or otherwise damaged power cord can cause a short circuit which could lead
to a fire or personal injury from electrical shock.
• Check the length of the power cord between the machine and power supply. Make sure the power
cord is not coiled or wrapped around any object such as a table leg. Coiling the power cord can
cause excessive heat to build up and could cause a fire.
• Make sure that the area around the power source is free of obstacles so the power cord can be
removed quickly in case of an emergency.
• Make sure that the power cord is grounded (earthed) at the power source with the ground wire on
the plug.
• Connect the power cord directly into the power source. Never use an extension cord.
• When you disconnect the power plug from the power source, always pull on the plug, not the
cable.
After Installation, Servicing
Points to Confirm with Operators
At the end of installation or a service call, instruct the user about use of the machine. Emphasize the
following points.
• Show operators how to remove jammed paper and troubleshoot other minor problems by
following the procedures described in the operating instructions.
• Point out the parts inside the machine that they should never touch or attempt to remove.
• Confirm that operators know how to store and dispose of consumables.
• Make sure that all operators have access to an operating instruction manual for the machine.
• Confirm that operators have read and understand all the safety instructions described in the
operating instructions.
• Demonstrate how to turn off the power and disconnect the power plug (by pulling the plug, not the
cord) if any of the following events occur: 1) something has spilled into the product, 2) service or
repair of the product is necessary, 3) the product cover has been damaged.
• Caution operators about removing paper fasteners around the machine. They should never allow
paper clips, staples, or any other small metallic objects to fall into the machine.
4
Safety Instructions for this Machine
Prevention of Physical Injury
1. Before disassembling or assembling parts of the machine and peripherals, make sure that the
machine and peripheral power cords are unplugged.
2. The plug should be near the machine and easily accessible.
3. If any adjustment or operation check has to be made with exterior covers off or open while the
main switch is turned on, keep hands away from electrified or mechanically driven components.
4. The inside and the metal parts of the fusing unit become extremely hot while the machine is
operating. Be careful to avoid touching those components with your bare hands.
5. To prevent a fire or explosion, keep the machine away from flammable liquids, gases, and
aerosols.
Health Safety Conditions
If you get ink in your eyes by accident, try to remove it with eye drops or flush with water as first aid. If
unsuccessful, get medical attention.
If you ingest ink by accident, induce vomiting by sticking a finger down your throat or by giving soapy
or strong salty water to drink.
Observance of Electrical Safety Standards
• The machine and its peripherals must be installed and maintained by a customer service
representative who has completed the training course on those models.
Safety and Ecological Notes for Disposal
• Dispose of replaced parts in accordance with local regulations.

Used ink and masters should be disposed of in an environmentally safe manner and in accordance
with local regulations.
The Aim of Anti-tip Components and Precautions
• The anti-tip components are necessary for meeting the requirements of IEC60950-1, the
international standard for safety.
• The aim of these components is to prevent the products, which are heavy in weight, from toppling
as a result of people running into or leaning on the products, which can lead to serious accidents
such as persons becoming trapped under the product. (U.S.: UL60950-1, Europe: EN60950-1)
5
• Therefore, removal of such components must always be with the consent of the customer. Do not
remove them at your own judgment.
6
Symbols and Trademarks
Symbols
This manual uses several symbols. The meanings of those symbols are as follows:
See or Refer to
Clip ring
E-ring
Screw
Connector
Clamp
[A]: Short Edge Feed (SEF)

[B]: Long Edge Feed (LEF)
Trademarks
Microsoft®, Windows®, and MS-DOS® are registered trademarks of Microsoft Corporation in the
United States and /or other countries.
PostScript® is a registered trademark of Adobe Systems, Incorporated.
PCL® is a registered trademark of Hewlett-Packard Company.
Ethernet® is a registered trademark of Xerox Corporation.
PowerPC® is a registered trademark of International Business Machines Corporation.
Other product names used herein are for identification purposes only and may be trademarks of their
respective companies. We disclaim any and all rights involved with those marks.
7
TABLE OF CONTENTS
Important Safety Notices...................................................................................................................................1
Responsibilities of the Customer Engineer....................................................................................................1
Customer Engineer................................................................................................................................1
Reference Material for Maintenance...................................................................................................1
Before Installation, Maintenance..................................................................................................................1
Shipping and Moving the Machine.....................................................................................................1
Power......................................................................................................................................................1
Installation, Disassembly and Adjustments..........................................................................................2
Special Tools..........................................................................................................................................2
During Maintenance......................................................................................................................................2
General..................................................................................................................................................2
Safety Devices........................................................................................................................................3
Organic Cleaners..................................................................................................................................3
Power Plug and Power Cord................................................................................................................3
After Installation, Servicing............................................................................................................................4
Points to Confirm with Operators.........................................................................................................4
Safety Instructions for this Machine...............................................................................................................5
Prevention of Physical Injury.................................................................................................................5
Health Safety Conditions......................................................................................................................5
Observance of Electrical Safety Standards.........................................................................................5
Safety and Ecological Notes for Disposal...........................................................................................5
The Aim of Anti-tip Components and Precautions...............................................................................5
Symbols and Trademarks...................................................................................................................................7
Symbols...........................................................................................................................................................7
Trademarks.............................................................................................................................................7
1. Product Information
Specifications....................................................................................................................................................15
Overview..........................................................................................................................................................16
Component Layout.......................................................................................................................................16
Electrical Component Layout......................................................................................................................17
Drive Layout..................................................................................................................................................25
Machine Codes and Peripherals Configuration............................................................................................26
Guidance for Those Who are Familiar with Predecessor Products..............................................................27
8
2. Installation Procedure
Installation Requirements.................................................................................................................................29
Optimum Environmental Condition............................................................................................................29
Environments to Avoid.................................................................................................................................29
Power Connection.......................................................................................................................................29
Machine Access...........................................................................................................................................29
Power Sockets for Peripherals.....................................................................................................................30
Optional Unit Combinations............................................................................................................................32
Machine Options.........................................................................................................................................32
Machine Installation.........................................................................................................................................33
Accessory Check..........................................................................................................................................33
Installation Procedure..................................................................................................................................34
Brand Setting................................................................................................................................................41
Platen Cover (D593).......................................................................................................................................43
Accessory Check..........................................................................................................................................43
Auto Document Feeder (D578)......................................................................................................................47
Accessory Check..........................................................................................................................................47
The Aim of Anti-tip Components and Precautions............................................................................48
ADF Stabilizer Installation...........................................................................................................................50
Configuration of Options............................................................................................................................51
SP6-2 Main-scan position - ADF.......................................................................................................51
SP6-4 Scan start position – ADF........................................................................................................51
Tape Dispenser (C651)...................................................................................................................................52
Accessory Check..........................................................................................................................................52
Network Controller (C654)............................................................................................................................56
Accessory Check..........................................................................................................................................56
Optional Drums (C618/C619/C620).........................................................................................................62
3. Preventive Maintenance
Maintenance Tables........................................................................................................................................63
9
4. Replacement and Adjustment
Beforehand.......................................................................................................................................................65
Special Tools....................................................................................................................................................66
Image Adjustment.............................................................................................................................................67
SP6-10: Master Writing Speed..................................................................................................................67
SP6-100 to 107: Paper Registration ........................................................................................................68
SP6-05, 6-06: Scanning Speed – Platen, ADF........................................................................................68
SP6-03, 6-04: Scanning Start Position – Platen, ADF..............................................................................68
SP6-01, 6-02: Main Scan Position – Platen, ADF....................................................................................69
SP6-20: Standard White Execution...........................................................................................................69
Covers and Boards..........................................................................................................................................70
Front Cover, Operation Panel....................................................................................................................70
Right Cover...................................................................................................................................................72
Left Cover......................................................................................................................................................73
Rear Cover...................................................................................................................................................74
Front Door Safety Switch.............................................................................................................................74
MPU..............................................................................................................................................................76
PSU................................................................................................................................................................78
Scanner Unit.....................................................................................................................................................79
Exposure Glass............................................................................................................................................79
Original Length Sensors..............................................................................................................................81
Exposure Lamp.............................................................................................................................................82
Reassembling.......................................................................................................................................84
Scanner Motor.............................................................................................................................................85
Sensor Board Unit (SBU).............................................................................................................................86
Exposure Lamp Stabilizer............................................................................................................................86
Scanner HP Sensor......................................................................................................................................86
Platen Cover Sensor ...................................................................................................................................87
Front Scanner Wire......................................................................................................................................88
Reinstalling the Front Scanner Wire...................................................................................................90
Rear Scanner Wire......................................................................................................................................93
Reinstalling the Rear Scanner Wire...................................................................................................94
Master Eject Unit..............................................................................................................................................96
10
Master Eject Unit..........................................................................................................................................96
Master Eject Safety Switch.................................................................................................................96
Eject Box Set Switch ...........................................................................................................................97
Master Feed...................................................................................................................................................102
Master Making Unit..................................................................................................................................102
Plotter Safety Switch..................................................................................................................................102
Thermal Head............................................................................................................................................103
Installation.........................................................................................................................................105
Duct Plate HP Sensor, Duct Plate Motor..................................................................................................106
Cutter Unit..................................................................................................................................................109
Thermal Head Driving Unit.......................................................................................................................109
Duct Jam Sensor Adjustment.....................................................................................................................110
Master Edge Sensor Adjustment..............................................................................................................111
2nd Drum Master Sensor Adjustment......................................................................................................112
Master End Sensor Adjustment.................................................................................................................113
Thermal Head Voltage Adjustment..........................................................................................................114
Paper Feed.....................................................................................................................................................116
Pick-Up Roller, Paper Feed Roller, Friction Pad......................................................................................116
Paper Feed Safety Cover..........................................................................................................................116
Paper Separation Pressure Adjustment....................................................................................................120
Paper Width Detection Board..................................................................................................................121
Printing............................................................................................................................................................122
Press Roller.................................................................................................................................................122
Press Roller Release Lever Adjustment.....................................................................................................122
Printing Pressure Adjustment.....................................................................................................................123
Drum...............................................................................................................................................................125
Preparation................................................................................................................................................125
Cloth Screen..............................................................................................................................................125
Installation.........................................................................................................................................126
Clamper, Metal Screen............................................................................................................................127
Installation.........................................................................................................................................128
Mylar Seal.................................................................................................................................................129
Ink Pump Adjustment.................................................................................................................................129
11
Ink Roller Unit, Ink Roller One-Way Clutch............................................................................................132
Idling Roller Motor, Idling Roller HP Sensor...........................................................................................133
Doctor Roller Gap Adjustment.................................................................................................................134
Ink Detection Adjustment...........................................................................................................................135
Main Motor Pulley Position.......................................................................................................................135
Main Drive Timing Belt Adjustment..........................................................................................................136
Paper Delivery ...............................................................................................................................................137
Paper Delivery Unit...................................................................................................................................137
Fan Motor, Exit Sensor..............................................................................................................................137
Exit Pawl Adjustment.................................................................................................................................138
Timing Adjustment.............................................................................................................................138
Clearance Adjustment......................................................................................................................139
Air Pump Adjustment.................................................................................................................................139
Chocks........................................................................................................................................................141
Network Printer Controller............................................................................................................................143
Printer Board..............................................................................................................................................143
Sound-proofing Cushions ............................................................................................................................145
Paper Feed Left, Paper Feed Right...........................................................................................................145
Paper Exit...................................................................................................................................................146
Master Eject Cover....................................................................................................................................146
Base............................................................................................................................................................147
Fuse, LED, VR, DIP-SW, AND TP Tables......................................................................................................148
Blown Fuse Conditions..............................................................................................................................148
PSU....................................................................................................................................................148
LED’S..........................................................................................................................................................148
MPU...................................................................................................................................................148
Controller Board...............................................................................................................................149
VR’S............................................................................................................................................................149
MPU...................................................................................................................................................149
PSU....................................................................................................................................................149
Ink detection board..........................................................................................................................150
Dip Switches..............................................................................................................................................150
Ink detection board..........................................................................................................................150
12
Controller Board...............................................................................................................................150
Test Points...................................................................................................................................................151
MPU...................................................................................................................................................151
PSU....................................................................................................................................................151
5. System Maintenance Reference
Service Program Mode.................................................................................................................................153
Using Service Program Modes................................................................................................................153
How to Select a Program Number..................................................................................................153
6. Troubleshooting
Firmware Update...........................................................................................................................................155
Type of Firmware.......................................................................................................................................155
Before You Begin.......................................................................................................................................155
Preparing To Download Firmware...........................................................................................................156
Download Main/ADF firmware..............................................................................................................157
Download FV-Lt firmware.........................................................................................................................158
Electrical Component Defects.......................................................................................................................161
Sensors.......................................................................................................................................................161
Switches.....................................................................................................................................................168
Power Supplies..........................................................................................................................................169
Controller...................................................................................................................................................170
7. Energy Saving
Energy Save...................................................................................................................................................171
Energy Save...............................................................................................................................................171
Timer Settings....................................................................................................................................171
Recommendation..............................................................................................................................171
Paper Save.....................................................................................................................................................173
Effectiveness of the Combine Function.....................................................................................................173
Combine mode.................................................................................................................................173
Recommendation..............................................................................................................................173
C279.................................................................................................................................................173
13
14
Specifications
See "Appendices" for the following information:
• Main Frame
• Supported Paper Sizes
• Software Accessories
• Optional Equipment
15
Overview
Component Layout
16
Overview
1. Scanner HP sensor
16. Paper table
2. 2nd carriage
17. Registration rollers
3. 1st carriage
18. Doctor roller
4. Original length sensor
19. Ink roller
5. Lens
20. Press roller
6. Blower fan motor
21. Idling roller
7. Reverse roller
22. Exit pawl
8. SBU
23. Transport belts
9. Tension roller
24. Vacuum fan motor
10. Master set roller
25. Paper delivery table
11. Platen roller
26. Air knife fan motors
12. Master roll
27. Master eject rollers
13. Thermal head
28. Master eject box
14. Paper separation roller
29. Vacuum fan motor
15. Paper feed roller
Electrical Component Layout
17
18
Overview
19
Boards
No. Component Function
6 CCD and SBU Outputs a video signal to the MPU.
Paper Width Detection Board Sends data about the paper width on the paper table to
18
the MPU.
20
Overview
30 Ink Detection Board Checks if there is ink in the drum.
36 Operation Panel Boards These boards control the operation panel.
37 Power Supply Unit (PSU) Provides dc power to the machine.
54 Main Motor Board Controls the main motor speed.
Main Processing Unit (MPU) Controls all machine functions, both directly and through
62
other boards.
70 Lamp Stabilizer This supplies power to the exposure lamp.
Motors
5 Scanner Motor Drives the scanner.
23 Master Feed Motor Feeds the master to the drum.
24 Table Motor Raises and lowers the paper table.
28 Printing pressure motor Raises and lowers the pressure roller.
31 Ink Pump Motor Drives the ink pump.
45 Master Eject Motor Sends used masters into the master eject box.
46 Air Knife Fan Motor 1

Rotates the fan to provide air to separate the leading
47 Air Knife Fan Motor 2
edge of the paper from the drum.
48 Air knife fan motor 3
Provides suction so that paper is held firmly on the

50 Vacuum Fan Motor
transport belt.
40 Paper Delivery Motor Feeds out the printed paper.
53 Pressure Plate Motor Raises and lowers the pressure plate.
57 Main Motor Rotates the drum.
59 Registration Motor Feeds the paper to align it with the master on the drum.
61 Paper Feed Motor Feeds the paper from the paper table.
21
67 Clamper Motor Opens or closes the master clamper on the drum.
72 Duct plate motor Opens or closes the duct plate at entrance of the duct.
74 Cutter Motor Cuts the master.
79 Duct fan motors Provides suction to guide the master into the duct.
81 Master Feed Motor Feeds the master to the drum.
83 Thermal head driving motor Raises and lowers the thermal head.
84 Blower fan motor Provides air to separate the master.
Presses or releases the drum idling roller against the drum

91 Idling roller motor
screen.
96 Ink Pump Motor Drives the ink pump.
Sensors
1 Scanner HP Sensor Detects when the image sensor is at home position.
3 Platen Cover Sensor Detects whether the platen cover is open or closed.
4 Original length sensor 1, 2 Detect the length of the original on the exposure glass.
13 Master Set Cover Sensor Checks if the master set cover is properly set.
Detects when the master making unit runs out of master

14 Master End Sensor
roll.
Detects when the paper table reaches the paper feed

17 Paper Height Sensor
position.
19 Paper Length Sensor Detects when long paper is on the paper table.
20 Paper End Sensor Detects when the paper table runs out of paper.
21 Registration Sensor Detects paper approaching the registration roller.
26 2nd drum master sensor Detects if there is a master on the drum.
Detects when the printing pressure is at the home

29 Printing pressure HP sensor
position.
22
Overview
39 Front Door Switching Sensor Detects if the Front Cover is in the closed position.
41 Master Eject Sensor Detects used master misfeeds.
42 Drum Master Sensor Detects if there is a master on the drum.
43 Pressure Plate HP Sensor Detects when the pressure plate is at the home position.
44 Pressure Plate Limit Sensor Detects when the pressure plate is in the lowest position.
49 Paper Exit Sensor Detects paper misfeeds at the exit.
Determines the paper misfeed check timing at the paper

55 2nd Feed Timing Sensor
registration area.
58 Feed Start Timing Sensor Determines the paper feed start timing.
60 Table Lower Sensor Detects when the paper table is at its lower limit position.
Master Eject Position (Drum HP)

63 Detects when the drum is at the master eject position.
Sensor
64 Paper Exit Timing Sensor Determines the paper exit misfeed check timing.
65 Clamper Closed Sensor Detects if the clamper is in the closed position.
66 Clamper Open Sensor Detects if the clamper is in the open position.
71 Duct plate HP sensor Detects when the duct plate is at the home position.
73 Cutter HP Sensor Detects when the cutter is at the home position.
76 Master Set Cover Sensor Checks if the master set cover is properly set.
Detects when the master making unit runs out of master

77 Master End Sensor
roll.
80 Duct jam sensor Detects when a master remains in the duct.
82 Thermal head HP sensor Detects when the thermal head is at the home position.
85 Master edge sensor Detects the leading edge of the master.
94 Ink idling roller HP sensor Detects when the idling roller is at home position.
23
Solenoids
27 Front Pressure Release Solenoid Releases the press roller to apply printing pressure.
56 Rear Pressure Release Solenoid Releases the press roller to apply printing pressure.
Switches
16 Master Making Unit Set Switch Checks if the master making unit is installed.
22 Table Lowering Switch Lowers the paper table.
32 Door Safety Switch Checks whether the front door is properly closed.
35 Main Switch Turns the power on or off.
Checks if the master making unit is installed.

38 Plotter Safety Switch Note: The master making unit is sometimes called the
‘plotter unit’.
52 Eject Box Set Switch Checks if the master eject box is installed.
68 Auto Off Switch Turns the power off automatically.
69 Master Eject Safety Switch Checks if the master eject unit is installed.
78 Lower master tray set switch Checks if the lower master tray is installed.
Counters
33 Paper Counter Keeps track of the total number of copies.
34 Master Counter Keeps track of the total number of masters made.
Others
2 Exposure Lamp (Xenon Lamp) Applies light to the original for exposure.
15 Thermal Head Burns the image onto the master.
Drum home position indicator LEDs that indicates the drum position.
25
(LEDs)
24
Overview
Drum thermistor Detects the temperature inside the drum to adjust various
92
processes.
93 Ink detection pins Detect if ink is present in the drum
Drive Layout
1. Pressure plate motor 7. Table motor

2. Clamper motor 8. Paper feed motor
3. Paper delivery motor 9. Duct plate motor
4. Printing pressure motor 10. Thermal head driving motor
5. Main motor 11. Master feed motor
6. Registration motor 12. Scanner motor
25
Machine Codes and Peripherals Configuration
No Item Machine Code Remarks
C279
1 Mainframe -11/-17/-27/-29
-61/-65
2 Platen Cover D593

One from No.2 or No.3
3 Auto Document Feeder D578
4 Network Controller C654
5 Tape Dispenser C651
6 Optional Drum C618/C619/C620
26
Guidance for Those Who are Familiar with Predecessor Products
Guidance for Those Who are Familiar with

Predecessor Products
Machine C279 is a successor model to Machine C264. If you have experience with the predecessor
products, the following information will be of help when you read this manual.
Different Points from Predecessor Products
C279 C264
Universal color Yes No
Three new language Traditional Chinese, Russian,

-
selections added *1 Turkish
Fine mode
New user modes added -
Protect code
New SP mode added Refer to the SP table section -
Controller FV-Lt (RPCS driver) VC-20 (Windows GDI)
@Remote Yes *2 No
Original size sensor Yes No
Firmware Update SD card IC card
• *1. Because of the increased number of languages, one firmware module cannot contain all the
languages, so the firmware is divided into two (depending on the model). When you update the
firmware, chose the right type of firmware.
• *2. Auto meter reading and Fleet report only. Printer controller is required.
27
28
Installation Requirements
Carefully select the installation location because environmental conditions greatly affect machine
performance.
Optimum Environmental Condition
1. Temperature: 10 to 30 °C (50 to 86 °F)

2. Humidity: 20 to 90 %RH
3. Install the machine on a strong and level base. The machine must be level within 5mm (0.2") both
front to rear left to right.
Environments to Avoid
1. Locations exposed to direct sunlight or strong light (more than 1,500 lux).
2. Dusty areas
3. Areas containing corrosive gases.
4. Locations directly exposed to cool air from an air conditioner or reflected heat from a space
heater. (Sudden temperature changes from low to high or vice versa may cause condensation
within the machine.)
Power Connection
1. Securely connect the power cord to a power source.

2. Make sure that the wall outlet is near the machine and easily accessible.
3. Make sure the plug is firmly inserted in the outlet.
4. Avoid multi-wiring
5. Do not pinch the power cord.
Machine Access
Place the machine near a power source, providing clearance as shown below.
29
Power Sockets for Peripherals
• Rating Voltage for Peripherals

• Make sure to plug the cables into the correct sockets.
30
Installation Requirements
31
Optional Unit Combinations

Machine Options
No. Options Remarks
1 Platen Cover (D593)

One from No.1 or No.2
2 Auto Document Feeder (D578)
3 Tape Dispenser (C651)
4 Network Controller (C654)
5 Optional Drums (C618/C619/C620)
32
Machine Installation
Accessory Check
Make sure that you have all the accessories listed below:
No. Description Quantity
1 Master Spool 2
2 Carrying Handle Stoppers 4
3 Operating Instructions (CD-ROM) 1
4 Easy Operation Guide 1
5 Manuals & Safety Information for this machine 1
6 NECR 1
7 Emblem Cover 1
8 Emblem (RICOH) 1
9 Operation Panel Logo Plate (RIC/SAV/LAN) 1×3
10 Sheet & Pocket for the Exposure Glass 1
11 Power Cable 1
33
Installation Procedure
1. Unpack the box. When installing the optional table, mount the machine as shown (there are 2
screws [A] packed with the table).
• Only lift with the carrying handles on the bottom corners of the machine.
• Secure the machine on the table with the 2 screws [A] provided. This prevents the machine
from falling from the table when the platen cover is open.
• Lock the casters of the table as shown [B], to prevent the machine from moving (e.g. when the
drum is set).
34
2. Push the carrying handles [C] into the machine, and attach the carrying handle stoppers[D].
35
3. Remove the filament tape and string securing the covers and units as shown above.
36
4. Remove the front tape [A], the tag [B], and the rear tape [C].
• To remove the rear tape, pull the portion shown in the diagram toward the front of the
machine.
37
5. Pull out the master making unit, and take out the accessory bag [A].
6. Insert both spools into a new master roll.
7. Install the master roll as shown above.
38
8. Insert the leading edge of the master roll under the platen roller. The arrows [A] indicate the correct
position of the master leading edge.
9. Close the cover [A] using both hands.

10. Set the master-making unit.
39
11. Open the door, and insert a new ink cartridge [A].
12. Open the paper table, and load a stack of paper.

13. Make sure that the side plates [A] touch the paper gently. Shift the lock lever [B] in the direction of
the arrow.
14. Raise the paper delivery table [A] slightly, then gently lower it.
15. Lift the side plates and the end plate, and adjust them to the paper size.
16. Firmly insert the power plug in the outlet.
17. Make sure that the wall outlet is near the machine and easily accessible.
40
18. Turn on the main switch [A].

19. Press the “Economy mode” key while holding down the “0” key, to supply ink inside the drum.
20. Make some test copies.
Brand Setting
If the machine was not set with the correct brand in the factory, you need to do this now.
1. Install your brand emblem [A] and emblem cover [B].
41
• When you set up the Ricoh brand model, install the emblem plate insted of the emblem and
emblem cover.
2. Select your brand in the SP mode.
Access SP2-7 (Vendor Selection) and choose your brand. ( Appendices – Main SP Tables)
42
Platen Cover (D593)
Platen Cover (D593)

Accessory Check
Check the quantity and condition of the accessories in the box against the following list:
1 Stepped Screw 2
2 Guard Rail Filler 1
1. Remove the strips of tape.
43
2. Insert the two stepped screws [A] on the top of the machine.
3. Peel off the double sided tape from the guard rail filler [A] and place it by the platen cover sensor
[B].
44
Platen Cover (D593)
4. Mount the platen cover [A] by aligning the screw keyholes over the stud screws.
5. Slide the platen cover toward the right of the machine.
6. Remove the platen sheet [B] from the platen cover [A].
7. Place the platen sheet on the exposure glass.
8. Slowly close the platen cover, gently pressing it against the platen sheet so that the sheet sticks to
the cover.
9. Open the platen cover again and lightly hold the Velcro part.
45
• When placing the platen sheet on the exposure glass, make sure to align it with the front left
corner.
10. Turn on the main switch.
11. Place an original on the exposure glass and confirm that it can be printed properly.
• The SMC sheet is contained in the front cover[C].
46
Auto Document Feeder (D578)

Accessory Check
1 Stepped Screw 2
2 Screw 2
3 Thumbscrew 4
4 Stabilizer Bracket 2
5 ADF exposure glass cleaning decal 1
6 EMC ADDRESS:RIC 1
47
The Aim of Anti-tip Components and Precautions
The anti-tip components are necessary for meeting the requirements of IEC60950-1, the international
standard for safety.
The aim of these components is to prevent the products, which are heavy, from toppling as a result of
people running into or leaning on the products, which can lead to serious accidents such as persons
becoming trapped under the product.
(U.S.: UL60950-1, Europe: EN60950-1)
Therefore, removal of such components must always be with the consent of the customer.
Do not remove them at your own judgment.
1. Remove the strips of tape.
• When unloading the ADF from a pallet, hold the front and rear sides of the ADF .
48
2. Insert the two stud screws [A] on the top of the machine.
49
3. Mount the ADF [A] by aligning the screw keyholes [B] of the ADF support plate over the stud
screws.
4. Slide the ADF toward the front of the machine.
5. Secure the ADF with the two knob screws [C].
6. Attach the interface cable [D] to the inlet of the machine.
7. Attach the original setting and ADF exposure glass cleaning decal [A] to the top cover as shown.
8. Plug in and turn on the main power switch, and then check the ADF operation.
ADF Stabilizer Installation
50
1. Attach the two stabilizer brackets [A] to the back of the table using the thumbscrews ( x 4).
• This procedure must be done to prevent the machine from falling backwards when the ADF is open.
Configuration of Options
SP6-2 Main-scan position - ADF
Adjust the image position of the ADF in the main scanning direction.
1. Make a copy in platen mode at 90 rpm (speed 3).
2. Measure the difference between the center of the main-scan on the original and on the print.
3. Access SP6-02, input the value and press the Enter key. (If you input a positive value, the image
moves towards the operation side.)
4. Repeat the procedure to make sure that there is no difference.
SP6-4 Scan start position – ADF
1. Input SP8-10 (Test patterns) and enter “6”, then press the start key.
2. Exit the SP mode, then make copies of the test pattern printed, in platen mode at 90 rpm (speed 3).
Use the 10th print for the adjustment.
3. The length of the 8 squares in the feed direction should be 130 mm.
4. If it is not, calculate the reproduction ratio using the following formula.{(130 - Value) / 130} x
100 = ± X.X % (Round off to one decimal place) Example: If the value is 133, {(130 - 133) /
130} x 100 = - 2.3 %
5. Access SP6-06, input the calculated ratio, and press the Enter key.
6. Check again to make sure that the ratio is correct.
51
Tape Dispenser (C651)

Accessory Check
Knob Screw (For C210, C217, C218, C219, C222, C223, C225, C228, 2
1 C238, C237, C238, C248, C249, C264, C267, C272, C276, C278,
and C279)
2 Screw M4 x 25 (For C211, C212, C213, C214, C216, C224, and C226) 2
Hexagon Nut M4 (For C211, C212, C213, C214, C216, C224, and 2
3
C226)
4 Auxiliary Bracket (For C226 and C267) 1
5 Auxiliary Bracket (For C238, C247 and C249) 1
6 Auxiliary Bracket (For C269) 1
7 Auxiliary Bracket (For C264 C272, C276, C278, and C279) 1
Screw M4 x 8 (For C226, C238, C247, C249, C264, C267 C272, 4

8
C276, C278, and C279)
9 Lock Washer (For C226 only) 1
10 Lock Washer (For all except C267) 1
11 Tape 1
52
1. Turn off the main switch and unplug the power cord.
2. Remove the paper delivery plate.
3. Install the auxiliary bracket [B] on the tape dispenser[A] with M4 x 8 screws (accessories).
4. Cut off the cover [C] in the rear cover, as shown.
5. Remove the connecter cover [D].
6. Remove the screw that is beside the connector [E].
7. Install the tape dispenser on the main body with two knob screws (accessories) in the two outer
holes in the tape dispenser bracket.
• Install the lock washer (accessories) with the lower of the two knob screws.
• Tighten the knob screws with a screwdriver to prevent them from coming loose.
8. Reinstall the paper delivery plate.
53
9. Open the tape dispenser cover [A]. Then, insert the leading edge of the tape into the tape entrance
until it stops as shown in the illustration [B].
• Be sure that the tape is installed in the proper direction. If it is not, the tape marker will not
work correctly.
10. Turn on the main switch of the main body.
11. Turn on the tape dispenser switch [A].
54
12. Press the tape cut button [A] to cut off the leading edge of the tape.
13. Check the tape dispenser operation using the Memory/Class modes of the main body.
55
Network Controller (C654)

Accessory Check
1 ACU Board (with Case) 2
2 Top Right Bracket 2
3 Bottom Bracket 2
4 Top Left Bracket 1
5 Short Harness 1
56
6 Long Harness 1
7 Ground Cable 1
8 Cover 1
9 Ferrite Core 1
10 Screw: M3x4 5
11 Screw: M3x6 4
12 Clamp 1
13 Attachment Kit for HP4R2.5*1 1
*1This item is not used for this machine.
• This circuit operates on a +5V circuit.
Prepare to install the board: Stage 1
57
1. Attach the three brackets [A], [B], [C] ( ×3).

2. Install the clamps [D] ( × 3).
3. Attach the harness [E] ( × 2, × 1).
Prepare to install the board: Stage 2
1. Check whether the “mm/inch” setting in the User Tools (System – mm/inch) is set to the correct
value. If necessary, change it to the correct “mm/inch” setting.
2. Check whether “SP2-7” (Vendor Selection) is set to the correct value. If necessary, change it to the
correct vendor setting. ( Appendices – Main SP Tables)
Install the controller in the main machine
1. Rear cover. ( p.74 "Rear Cover")
58
2. Open the two clamps to release this part of the harness [A], which will be connected to the
controller.
3. Remove the bracket [B] ( × 1).
59
4. Attach the board [A] ( × 3).
60
5. Connect the harness [A][B] ( × 2, × 3).
• After installing the printer controller unit, make sure that the board and the cable are securely
connected.
61
Optional Drums (C618/C619/C620)
There are three types of optional drum units:

A3 Size: Color drum
B4 Size: Color drum
A4 Size: Black drum (Black ink only)
1. Remove the protective sheet [A] and the lock [B] from the drum unit.
2. Remove the tape securing the ink holder.
3. Attach a color indicator decal to the drum case. The decal must be the same color as the ink in use.
4. Remove the drum unit.
5. Leave the master wrapped around the removed drum to protect the drum from dust and from
drying.
6. Keep the removed drum unit in the drum case.
7. Install the drum unit.
• The color drum indicator (or A4 drum indicator) on the operation panel stays lit when a drum
is mounted in the machine.
8. Remove the ink cartridge cap.
9. Insert the ink cartridge in the ink holder.
62
Maintenance Tables
See “Appendices” for the following information.
• Appendix: PM Tables
• Appendix: Service Call Conditions
• Appendix: Service Program Mode
63
64
Beforehand
• Turn off the main power switch and unplug the machine before attempting any of the procedures in
this section.
Before you start to work on the machine, please do the following:

If there are printer jobs in the machine, print out all jobs in the printer buffer.
Turn off the main switch and disconnect the power cord and the network cable.
65
Special Tools
The following are the special tools used for service.
Part Number Description Quantity
B645 5010 SD Card 1
B645 6705 PCMCIA Card Adapter 1
B645 6830 USB Reader/Writer 1
A006 9104 Scanner positioning pins (4 pins as a set) 1
A0699502 Alvania 2 Grease 1
66
Image Adjustment
Image Adjustment
Adjusts the image position on prints by changing the SP settings.
Adjust the following in the given order.
SP6-10: Master writing speed
SP6-100 to 107: Paper registration
SP6-05: Scanning speed - platen
SP6-06: Scanning speed - ADF mode
SP6-03: Scan start position - platen
SP6-04: Scan start position - ADF
SP6-01: Main scan position - platen
SP6-02: Main scan position - ADF
SP6-20: Standard white execution (CCD calibration)
When correcting errors made when printing with the controller, use only the first two steps.
When correcting errors made when printing with scanned originals, do all adjustments in the given
order.
SP6-10: Master Writing Speed
1. Input SP8-10 (Test patterns) and enter “6”, then press the Start key.
2. Exit the SP mode, then print 10 copies at 90 rpm (speed 3). Use the 10th print for the adjustment.
3. The length of the 8 squares in the feed direction should be 130 mm, as shown above.
67
4. If it is not, calculate the reproduction ratio using the following formula.

{(130 - Value) / 130} x 100 = ± X.X % (Round off to one decimal place)
Example: If the value is 133, {(130 - 133) / 130} x 100 = - 2.3 %
6. Repeat the procedure to make sure that the ratio is correct.
SP6-100 to 107: Paper Registration
1. Input SP8-10 (Test patterns) and enter “6”, then press the Start key.
2. Exit the SP mode, then print 10 copies at 90 rpm (speed 3). Use the 10th print for the adjustment.
3. The space between the leading edge and the next line should be 8 mm, as shown above.
4. If it is not, access SP6-100 to 107, input the difference and press the Enter key.
Example: If the value is 7 mm, 7 - 8 = -1.0
5. Repeat the procedure to make sure that the gap is correct.
SP6-05, 6-06: Scanning Speed – Platen, ADF
1. Make copies of the test pattern printed during the previous adjustments ( p.67 "Image
Adjustment"), in platen mode at 90 rpm (speed 3). Use the 10th print for the adjustment.
3. If it is not, calculate the reproduction ratio using the following formula.
{(130 - Value) / 130} x 100 = ± X.X % (Round off to one decimal place)
6. Make copies of the test pattern in ADF mode and repeat the process using SP6-06.
SP6-03, 6-04: Scanning Start Position – Platen, ADF
1. Make copies of the test pattern printed during the previous adjustments ( p.67 "Image
Adjustment"), in platen mode at 90 rpm (speed 3). Use the 10th print for the adjustment.
2. The space between the leading edge and the next line should be 8 mm.
3. If it is not, access SP6-03, input the gap value and press the Enter key.
Example: If the value is 7 mm, 7 - 8 = -1.0
68
Image Adjustment
4. Repeat the procedure to make sure that the gap is correct.

SP6-01, 6-02: Main Scan Position – Platen, ADF

2. Measure the difference between the center of the main-scan on the original and on the print.
3. Access SP6-01, input the gap value and press the Enter key. (If you input a positive value, the
image moves towards the operation side.)
5. Make a copy in ADF mode and repeat the process using SP6-02.
SP6-20: Standard White Execution
Do this after one of the following is replaced:

• RAM on the MPU
• White plate located behind the original scale.
Do it at the end of the image adjustment procedure
1. Place a stack of 10 sheets of paper on the exposure glass.
2. Access SP6-20 and then press the Enter key to start the auto calibration.
69
Covers and Boards

Front Cover, Operation Panel
1. Right cover ( p.72 "Right Cover")

2. Left cover ( p.73 "Left Cover")
70
Covers and Boards
3. Remove the screws on the front door [A] ( x 2).
4. Remove the screws on the operation panel [A] and the connectors on the back side of the
operation panel. ( ×2 × 4)
• It might be difficult to remove the panel due to projections inside the front cover. Be careful not
to damage the cover or other parts when removing the cover from inside the front cover.
71
Right Cover
2. Master Making Unit ( p.102 "Master Making Unit")
3. Right cover [A]. ( × 2)
72
Covers and Boards
Left Cover
2. Left cover [A]. ( × 2)
73
Rear Cover
[A]: Rear cover ( × 8)
Front Door Safety Switch
1. Front Cover. ( p.70 "Front Cover, Operation Panel")
74
Covers and Boards
2. Front Door Safety Switches. ( × 3, × 2)
75
MPU
76
Covers and Boards
2. MPU [A] ( × 25, × 11, × 9)
3. NVRAM [A]
77
• Adjust the master end sensor, duct jam sensor, master edge sensor, and 2nd drum master sensor
( Master Feed –p.110 "Duct Jam Sensor Adjustment", p.111 "Master Edge Sensor
Adjustment", p.112 "2nd Drum Master Sensor Adjustment" and p.113 "Master End Sensor
Adjustment") after installing the new MPU.
• If you install a new RAM, you must do the image adjustments ( p.67 "Image Adjustment").
PSU

2. Master eject unit ( p.96 "Master Eject Unit")
[A]: PSU ( × 5, × 2, × 2)
When the PSU is replaced, the thermal head voltage returns to the default. Adjust the thermal head
voltage ( p.114 "Thermal Head Voltage Adjustment") after installing the new board.
78
Scanner Unit
Scanner Unit
Exposure Glass
1. Open the ADF or platen cover.
2. Glass cover [A] ( × 4)
3. Disconnect the DF I/F cable [A]
79
4. ADF exposure glass [A]
• Position the white marker [B] at the rear left corner when you reattach the ADF exposure glass.
5. Rear scale [A] ( × 3)
80
Scanner Unit
6. Exposure glass [A] with left scale
• Position the marker at the front left corner when you reattach the exposure glass.
Original Length Sensors
1. Exposure glass with left scale ( p.79 "Exposure Glass")
2. SBU cover [A] ( × 6)
• The three screws [B] do not need to be fully removed. Just loosen them to remove the SBU
cover.
3. Original length sensors [A] (hooks, ×1, × 1 each)
81
Exposure Lamp
1. Rear cover( p.74 "Rear Cover")

2. Operation panel ( p.70 "Front Cover, Operation Panel")
3. Exposure glass ( p.79 "Exposure Glass")
4. Scanner rear cover [A] ( × 1)
5. Disconnect the connector [A] from the lamp stabilizer [B].
82
Scanner Unit
6. Move the carriage unit [A] to the cutout position [B].
7. Cable guide [A] (hooks)
• Keep the cable guide for reassembling.

8. Adjustor clamp [B] ( × 1)
9. Pulley [C]
83
10. Release the cable clamp [A] (one hook under the cable clamp) at the rear edge of the exposure
lamp.
11. Hold down the snap [B], and then slide the exposure lamp [C] to the front side.
12. Exposure lamp [C]
Reassembling
84
Scanner Unit
Run the cable so there is no slack. Slide the adjustor clamp [A] to adjust the cable slack.
• [B]: Good
• [C]: Not good
Scanner Motor
1. Rear cover ( p.74 "Rear Cover")
2. Scanner motor assembly [A] ( × 2, spring × 1, × 1, timing belt × 1)
3. Scanner motor [A] ( × 2, ground plate [B] × 1)
• Make sure that the ground plate [B] is attached when installing the scanner motor in the scanner
motor bracket.
• Do the scanner image adjustment after replacing the scanner motor
85
Sensor Board Unit (SBU)

2. Original length sensor assembly ( × 2, ×2, × 2)
3. Sensor board unit [A] ( × 4, ground screw × 1, × 2)
Exposure Lamp Stabilizer
2. Exposure lamp stabilizer assembly [A] ( × 2, × 2)
Scanner HP Sensor
86
Scanner Unit
2. Scanner rear cover ( p.82 "Exposure Lamp")
3. Move the 1st scanner carriage [A] to the right side by rotating the scanner motor [B] clockwise.
4. Remove the mylar [A].

5. Remove the scanner HP sensor [B] ( × 1, hooks).
Platen Cover Sensor
1. Scanner rear cover ( p.82 "Exposure Lamp")
87
2. Holder bracket [A] ( × 1)

3. Platen cover sensor [B] ( × 1)
Front Scanner Wire

5. Scanner left stay [A] ( × 3)

6. Scanner front frame [B] ( × 5, × 3)
88
Scanner Unit
7. Take aside the connector bracket [A] ( × 2).

8. Scanner rear frame [B] ( × 8, × all, × all)
9. Scanner motor assembly ( p.85 "Scanner Motor")
10. Rear scanner drive pulley [A] ( × 1)
89
11. Front scanner wire clamp [A]

12. Loosen the front scanner wire bracket [B] ( × 1)
13. Front scanner wire.
14. Move the shaft [C] in the red arrow direction ( × 1: at front), and remove the scanner drive pulley
[D] ( × 1).
Reinstalling the Front Scanner Wire
90
Scanner Unit
1. Position the center ball [A] in the middle of the forked holder.
2. Pass the right end (with the ball) [B] through the square hole. Pass the left end (with the ring)
through the notch.
3. Wind the right end counterclockwise (shown from the machine’s front) five times. Wind the left end
clockwise three times.
• The two green marks [C] come together when you have done this. Stick the wire to the pulley
with tape. This lets you easily handle the assembly at the time of installation.
4. Install the drive pulley on the shaft [A] ( × 1, × 1).
• Do not attach the pulley to the shaft with the screw at this time.
5. Insert the left end into the slit [B]. The end should go via the rear track of the left pulley [C] and the
rear track of the movable pulley [D].
91
6. Hook the right end onto the front scanner wire bracket [A]. The end should go via the rear track of
the right pulley [B] and the rear track of the movable pulley [C].
• Do not attach the scanner wire bracket with the screw at this time.
7. Remove the tape from the drive pulley.
92
Scanner Unit
8. Insert a scanner positioning pin [A] through the 2nd carriage hole [B] and the left holes [C] in the
front rail. Insert another scanner positioning pin [D] through the 1st carriage hole [E] and the right
holes in the front rail [F].
9. Insert two more scanner positioning pins through the holes in the rear rail.
10. Screw the drive pulley to the shaft [G].
11. Screw the scanner wire bracket to the front rail [H].
12. Install the scanner wire clamp [I].
13. Pull out the positioning pins.
• Make sure the 1st and 2nd carriages move smoothly after you remove the positioning pins. Do
steps 8 through 13 again if they do not.
Rear Scanner Wire

5. Scanner front frame( p.88 "Front Scanner Wire")
6. Scanner left stay ( p.88 "Front Scanner Wire")
7. Scanner rear frame ( p.88 "Front Scanner Wire")
8. Follow steps 10 through 14 in the Front Scanner Wire procedure. You can remove the rear
scanner wire in the same way as replacing the front scanner wire.
93
Reinstalling the Rear Scanner Wire
1. Position the center ball [A] in the middle of the forked holder.
2. Pass the left end (with the ball) [B] through the drive pulley notch. Pass the right end (with the ring)
through the drive pulley hole.
3. Wind the left end [B] clockwise (shown from the machine’s front) five times. Wind the right end
counterclockwise three times.
• The two green marks [C] come together when you do this. Attach the wire to the pulley with
tape. This lets you easily handle the assembly at the time of installation.
4. Install the drive pulley on the shaft.
• Do not attach the pulley on the shaft with the screw at this time.
5. Install the wire.
• The winding of the wire on the three pulleys at the rear of the scanner should be the same as
the winding on the three pulleys at the front. This must show as a mirror image.
Example: At the front of the machine, the side of the drive pulley with the three windings must face the
front of the machine. At the rear of the machine, it must face the rear.
Do steps 7 through 13 from the "Reinstalling the Front Scanner Wire"( p.88 "Front Scanner Wire")
94
Scanner Unit
• When removing the rear scanner wire, removing the timing pulley [A] is required before moving the
shaft ( × 1).
95
Master Eject Unit

Master Eject Unit
[A]: Master eject unit ( ×1, × 2, × 1)
Master Eject Safety Switch
1. Master Eject Unit( p.96 "Master Eject Unit").
96
Master Eject Unit
2. Remove the Master Eject Safety Switch. ( × 1, × 1)
Eject Box Set Switch
1. Remove the Master Eject Unit. ( p.96 "Master Eject Unit").
97
2. Remove the cover. ( × 4)
98
Master Eject Unit
3. Remove the face plates ( × 5)
4. Remove the Air Knife Fan [A]. ( × 1, × 2)
99
5. Remove the plate [A].( × 1)
6. Remove the Eject Box Set Switch( × 1, × 1).
100
Master Eject Unit
101
Master Feed
Master Making Unit
[A]: Master making unit ( × 2)
Plotter Safety Switch
1. Master Making Unit ( p.102)

2. Remove the Plotter safety switch. ( × 4, × 1)
102
Master Feed
Thermal Head
1. Remove the master making unit ( p.102 "Master Making Unit")
103
2. Open the platen roller unit [1].

3. Remove the following:
[A]: T/H upper cover ( × 2)
[B]: T/H side cover ( × 1)
4. Close the platen roller unit [1].

5. Remove the thermal head [C] ( × 2).
6. Turn the thermal head clockwise and remove a tab (1).

7. Turn the thermal head counterclockwise, and remove a tab (2).
104
Master Feed
8. Remove the thermal head slowly.
• If you cannot access SP modes, open the master making unit and loosen the 2 screws [D].
Installation
1. Insert the tabs (1) at the operation side and the middle.
2. Turn the thermal head counterclockwise and insert the tab (2) at the front.
105
3. Turn the thermal head clockwise and insert the tab (3) at the non-operation side.
Make sure to follow the above procedure or the thermal head will not be installed correctly.
• Fit the base’s springs [A] over the protrusions [B] on the underside of the thermal head (6 points).
• While fitting the tops of the springs [A] over the protrusions on the underside of the thermal head,
make sure that all protrusions are properly fitted into the springs.
• Adjust the thermal head voltage ( p.114 "Thermal Head Voltage Adjustment") after installing
the new thermal head
Duct Plate HP Sensor, Duct Plate Motor
1. Master making unit ( p.102 "Master Making Unit")
2. Remove the cover [A] ( × 2, × 2)
106
Master Feed
3. Remove the duct plate HP sensor ( × 1)
4. Remove the rear rail bracket [A] ( × 2, × 1)
107
5. Remove the duct plate motor [A] ( × 3, × 2, × 2)
108
Master Feed
Cutter Unit
[A]: Cutter unit ( × 1, × 1)
Thermal Head Driving Unit
• Thermal head ( p.103 "Thermal Head")

• Rear cover ( p.74 "Rear Cover")
• Cutter unit ( p.109 "Cutter Unit")
109
[A]: Anti-static roller

[B]: Thermal head driving unit ( × 2, × 2)
Duct Jam Sensor Adjustment
Ensures that the sensor detects when a master remains in the duct.
Standard: 0.5 volts (within “+0.1” and “-0.1”volts)

Tools: Circuit tester
1. Check if a master remains in the duct. If a master remains in the duct, remove the master from the
duct.
2. Connect the terminals of a circuit tester to TP102 and a grounded place (e.g. iron base)
3. Connect the power plug, and turn on the main switch to access SP mode.
4. Select SP6-52 (Duct jam sensor voltage).
5. Press the Print Start key.
6. Measure the voltage with the circuit tester, and turn VR102 until the value becomes between “-0.1”
and “+0.1” volts from the standard value (0.5 volts)
• When the voltage cannot be adjusted to the standard value, adjust the threshold level of the duct
jam sensor. (SP6-52: Duct jam sensor voltage)
110
Master Feed
Standard Value Standard Value

Threshold level (SP6-52)
Master present Master not present
Above 2.0V 2.0V 0.5 +-0.1V
Master Edge Sensor Adjustment
Ensures that the sensor detects the leading edge of the master.

3. Select SP6-51 (Master edge sensor voltage).
4. Remove the lower master tray.
5. Pull out the master-making unit from the machine and open the master set cover.
6. Insert the leading edge of the master under the master tension roller, then close the master set cover
and reinstall the master-making unit in the machine.
and “+0.1” volts from the standard value (3.0 volts).
• When the voltage cannot be adjusted to the standard value, adjust the threshold level of the master
edge sensor. (SP6-51: Master edge sensor voltage)
111

3.0V+-0.1V 2.8V Above 3.0V
2nd Drum Master Sensor Adjustment
Ensures that the sensor detects if there is a master on the drum.

1. Check that there is a master wrapped on the drum.
4. Select SP6-53 (2nd drum master sensor voltage) and press the master-making key.
6. Turn off the main switch, then remove the master that is wrapped around the drum and install the
drum in the main body.
7. Turn on the main switch to access SP mode.
8. Select SP6-53 (2nd drum master sensor voltage) and press the master-making key.
9. Check if the value of the voltage becomes below 0.8 volts.
10. If the voltage is not correct, clean the black patch [A] on the screen.
112
Master Feed
• When the voltage cannot be adjusted to the standard value, adjust the threshold level of the 2nd
drum master sensor. (SP6-53: 2nd drum master sensor voltage)

2.2V+-0.1V 1.0V Below 0.8V
Master End Sensor Adjustment
Ensures that the sensor detects the end mark (a solid black area) on the master roll.
Standard: 1.8 volts (within “+0.1” and “-0.1” volts)
Tools: Circuit tester, the core of a used master roll (the core has no master)

1. Connect the terminals of a circuit tester to TP101 and to a grounded place (e.g. iron base).
2. Put a piece of master [A] on the used master roll.
3. Place the core of the used master roll inside the master-making unit, and close the master-making
unit.
• Insert the core so that the piece of master [A] faces towards the master end sensor.
4. Connect the power plug, and turn on the main switch.
113
• Please refer to the following table for the standard voltages.

• If the voltage cannot be adjusted to the standard value, do not change the threshold level
using SP6-50 (Master end sensor voltage).
Standard value
When set a new roll
Master end (4 layers of master End mark only
(master present)
on the core)
Above 3.0V Below 2.0V Below 0.8V
Thermal Head Voltage Adjustment
• This adjustment is always required when the thermal head or PSU has been replaced.
Purpose: To maintain master making quality and extend the lifetime of the thermal head.
Standard: Refer to the voltage value (X) printed on the thermal head. The value varies from one thermal
head to another.
The adjustment voltage should be between X and X - 0.1 V.
114
Master Feed
• Left cover ( p.73 "Left Cover")

• Read the voltage value on the decal on the thermal head.
1. Slide out the master making unit.
• Never turn VR1 clockwise rapidly while the master making unit is connected. The T/H will be
damaged if too much voltage is supplied suddenly.
2. Connect the positive terminal of a circuit tester to TP701 and the negative terminal to TP702.
• If the output and ground terminals touch each other, the board will be damaged.
4. Select SP5-12 (VHD signal).
5. Press the Start key. Power is continuously supplied to the thermal head, so press the Stop key if you
cannot finish the adjustment quickly.
6. A beeper sounds while the power is being supplied.
7. Measure the voltage, and turn RV1 so that the value becomes between “+0” and “-0.1” volts from
the value on the thermal head decal.
115
Paper Feed
Pick-Up Roller, Paper Feed Roller, Friction Pad
• Lower the paper table.

[A]: Pick-up roller ( × 1)
[B]: Paper guide ( × 1)
[C]: Feed roller ( × 1)
[D]: Friction pad
Paper Feed Safety Cover
1. Pick-Up Roller. ( p.116 "Pick-Up Roller, Paper Feed Roller, Friction Pad")
2. Paper Feed Roller. ( p.116 "Pick-Up Roller, Paper Feed Roller, Friction Pad")
3. Friction Pad. ( p.116 "Pick-Up Roller, Paper Feed Roller, Friction Pad")
4. Rear Cover. ( p.74 "Rear Cover")
116
Paper Feed
5. MPU. ( p.76 "MPU")
117
6. MPU Cover. ( ×7)
7. Remove the Wire [A].

8. Remove the Pulley [B]( ×1)
9. Loosen the screws [A].
118
Paper Feed
10. Remove the Shaft [B] by sliding it to the right.
11. Remove the paper feed safety cover. ( ×2)
119
Paper Separation Pressure Adjustment
Purpose: To ensure that the friction pad exerts sufficient pressure for smooth printing paper separation.
Default: The next position to the top.
Adjust the separation pressure by loosening and moving the screw [A] up or down.
• Moving up the screw Increases the paper separation pressure
• Moving down the screw Decreases the paper separation pressure
Tighten the screw after the adjustment
120
Paper Feed
Paper Width Detection Board
• Lower the paper table.

[A]: Paper table ( × 1, × 2)
[B]: Table cover ( ×5, 3 washers)
[C]: Sensor cover ( × 2)
[D]: Paper width detection board ( × 1, × 1)
121
Printing
Press Roller
• Take care to avoid possible injury. If the printing pressure release arms disengage, the press roller
will be pulled upwards suddenly
• Remove the drum.

[A]: Press roller ( × 1)
The bearings on the rear and front differ. During installation, ensure that the bearing with the stopper [B]
is positioned towards the rear of the machine.
Press Roller Release Lever Adjustment
Purpose: To maintain the correct clearance between the press roller arms and press roller lock levers.
This ensures that the press roller is correctly released and pressed against the drum when the press roller
release solenoid is energized.
Standard: 0.6 to 1.2 mm
Tools: A thickness gauge
122
Printing
• Front cover ( p.70 "Front Cover, Operation Panel")

1. Turn the drum manually until the drum master clamper on the drum moves into the lowest position.
(This is when the high points of the cams on the drum flanges meet with the cam followers on both
ends of the press roller.)
• To find out the correct position of the drum for the adjustment, look at the rear end of the drum
shaft. The recess on the drum drive gear meets the hole [A] in the bracket when the drum is in
the correct position.
2. Using a thickness gauge, measure the clearance [B] between the press roller arm [C] and the press
roller lock lever [D] (rear side). It should be between 0.6 and 1.2 mm.
3. If it is not correct, adjust the position of the press roller lock lever after loosening the two screws [E].
4. Repeat steps 2 and 3 for the front side.
Printing Pressure Adjustment
Improves print results without decreasing the run length.

Standard: Within 17 +-0.2 mm
123
• Paper delivery unit ( p.137 "Paper Delivery ")

1. Adjust the distance [A] to 17 +-0.2 mm by turning the adjusting bolt [B].
2. Repeat the same procedure for the printing pressure spring at the non-operation side.
• This is the adjustment for the standard printing pressure.

• If print density is incorrect, you can also adjust printing pressure with SP 2-35 or SP 6-70 to 6-87
( Appendices – Main SP Tables).
124
Drum
Drum
Preparation
Before attempting any of the procedures in this section, wipe off the ink around the ink roller. To do this,
set SP2-10 (ink detection board) to OFF, and feed paper until ink ends.
After finishing the required procedures in this section, do not forget to return SP2-10 to the default (Ink
detection board ON).
Cloth Screen
• Remove the drum.

1. Remove the drum upper bracket ( × 4).
2. Release the stopper [A], then rotate the drum until the master clamper faces top.
3. Remove the cloth screen [B] ( × 4).
125
Installation
• Do not scratch the cloth screen or metal screen.

• Properly insert the edge of the belt cloth [A] on the cloth screen under the mylar [B] on the metal
screen, as shown above. Otherwise, ink will leak from the trailing edge of the master on the drum
during a long printing run.
• Make sure that the correct side of the screen is facing up. In addition, make sure that the stays for
securing the cloth screen are positioned correctly. (Refer to the upper right illustration.)
• When replacing the cloth screen, spread the screen around the metal screen while strongly pulling
the stay [C]. Adjust the stay so that it is parallel to the master clamper, then tighten the screws.
• Make sure that the cloth screen is not wrinkled while spreading it around the drum.
126
Drum
Clamper, Metal Screen
• Remove the drum

Cloth screen ( p.125 "Cloth Screen")
[A]: Clamper lever (1 hexagon screw)
[B]: Clamper - open the clamping plate [C], then remove the clamper.
• Do not allow ink to get on the inside of the clamping plate [C]. If it is dirty with ink, the master may
slip off and the image position on the prints will move toward the trailing edge of the prints during a
printing run.
• Use a cloth dampened with water to clean the inside of the clamping plate [C]. Never use alcohol
or other solvents. The clamping force of the magnet will be weakened.
[D]: Tape (do not lose it)
[E]: Metal screen ( × 12)
127
Installation
• Make sure that the correct end of the metal screen is overlapping. (The right side overlaps, as
viewed from the non-operation side, as shown above.)
• The 4 screws holding the drum master clamper are longer than the 12 screws holding the metal
screen, although they are similar in appearance. Be careful not to mix them up or use the wrong
screws.
• When installing the metal screen, secure the trailing edge first with the 2 screws. Then, tighten the
other screws while removing the slack from the screen. Make sure that the gap between the drum
flanges and the screen is 0.3 mm or less, as shown above. (The two holes [A] on the trailing side
are round holes and the other holes are long holes, to allow for the removal of the slack.)
• Do not scratch the cloth screen or metal screen.
• If there is no filament tape [B] where the metal screen is overlapping, replace the filament tape. (W:
19mm × L: 355mm)
128
Drum
Mylar Seal
[A]: -0.5 to 0.5 mm

[B]: 5.6 to 7.2 mm
[C]: 4.9 to 6.5 mm
Attach the mylar seal at the attachment position on the metal screen as shown above.
• Clean the attachment position using isopropyl alcohol.
Ink Pump Adjustment
Purpose: To ensure the smooth operation of the ink pump plunger by properly positioning its holder.
129
• Remove the drum

[A]: Lower pump cover ( × 2)
[B]: Upper pump cover ( × 3)
1. Remove the E-ring [C] to free the plunger from the pump drive slider [D].
2. Loosen the two screws securing the holder [E]. (Do not remove the holder.)
3. Push the plunger [F] until it reaches the bottom.
• The end of the plunger [F] must not stick out from the holder [E].
130
Drum
4. Check that the piston motion is smooth.

5. If the motion is stiff, loosen the pump screws [G] and adjust the pump position.
6. After tightening, repeat step 4 and step 3.
7. Re-tighten the two screws [H].

8. Check that the piston motion is smooth.
9. Reinstall the E-ring [C].
131
Ink Roller Unit, Ink Roller One-Way Clutch
• Metal screen ( p.127 "Clamper, Metal Screen")

• Pump covers ( p.129 "Ink Pump Adjustment")
[A]: Board cover ( × 2)
[B]: Front stay ( × 2, × 3)
[C]: Front flange
[D]: Rear stay ( × 2)

[E]: Rear stoppers ( × 1)
[F]: Ring
132
Drum
[G]: Rear flange
[H]: Ink roller unit

[I]: Ink roller one-way clutch
Idling Roller Motor, Idling Roller HP Sensor
• Cloth Screen ( p.125 "Cloth Screen")

• Clamper, Metal Screen ( p.127 "Clamper, Metal Screen")
[A]: Idling roller HP sensor ( × 1, × 1)
[B]: Idling roller motor ( × 1, × 2)
133
Doctor Roller Gap Adjustment
Controls ink thickness around the ink roller.

Standard: 0.07 mm gauge passes, 0.09 mm gauge does not.
Tools: Thickness gauge
• Normally, the doctor roller gap is not adjusted or changed. It tends to be difficult to change in the
field. If the gap is too narrow, an uneven image may appear on the prints. If it is too wide, too
much ink will be applied to the drum screens, resulting in ink leakage from the drum.
• Ink roller unit ( p.132 "Ink Roller Unit, Ink Roller One-Way Clutch")
1. Make sure that a 0.07 mm gap gauge goes through the gap [A] between the ink and doctor
rollers, and that a 0.09 mm gap gauge does not.
• The gap should be checked at both ends of the doctor roller. Insert a gap gauge at each end
of the roller. The gap tends to be larger for the center.
• While the gap gauge is inserted, hold the doctor and ink rollers with your fingers in order to
stop the rollers from rotating.
• While the gap gauge is inserted, hold the end of the gap gauge
2. If the gap is out of the standard, loosen the screw [B] and adjust the gap by turning the cam
bushing [C] for the front and for the rear.
• Make sure to repeat the adjustment for both ends of the rollers.
134
Drum
Ink Detection Adjustment
Purpose: To ensure that the CPU detects a no-ink condition.
• Before attempting this procedure, wipe off the ink around the ink roller. To do this, set SP2-10 (ink
detection board) to OFF, and feed paper until ink ends.
• After finishing this procedure, do not forget to return SP2-10 to the default (ink detection board on).
• SP6-40 Ink detection adjustment ( Appendices - Main SP Tables)
Main Motor Pulley Position
After putting the pulley back on the main motor shaft, refer to the above illustration for the correct
position of the pulley.
135
Main Drive Timing Belt Adjustment
Purpose: After the timing belt is replaced, correct belt tension must be applied.
• Rear covers ( p.74 "Rear Cover")
• MPU ( p.76 "MPU")
1. Loosen the screws [A], [B], and [C].
2. Move the tension roller [D] to the right with a screwdriver [E] as shown.
3. Tighten the screws [A], [B], and [C].
4. Remove the screwdriver.
136
Paper Delivery
Paper Delivery
Paper Delivery Unit
[A]: Paper delivery cover ( ×4)

[B]: Paper delivery unit ( × 3, × 2)
Fan Motor, Exit Sensor
• Paper delivery unit ( p.137 "Paper Delivery ")

[A]: Paper guide ( × 2)
137
[B]: Delivery belts

[C]: Vacuum fan motor ( × 1, × 4)
[D]: Paper exit sensor ( × 1)
Exit Pawl Adjustment
Ensures that the exit pawls can move out of the way of the drum master clamper while the drum is
rotating.
Timing Adjustment
• When releasing the stoppers from the brackets, note that the press roller goes up quickly.
1. Turn the drum manually until the recess in the drum drive gear meets the positioning hole[A] in the
bracket, as shown.
2. Release the stopper at the operation side [B] from the pressure arm [C].
• Slide the stopper [B] to the left, and then lift the pressure arm [C].
138
Paper Delivery
3. Loosen screws [D] and [E]. Then measure the gap between the cam follower and cam face (front
drum flange). It should be 0 to 0.5 mm. Then re-tighten the two screws while pushing the cam
follower against the cam face.
4. Lock the stopper on the operation side with the lock bracket to keep the press roller in its correct
position.
5. Do the clearance adjustment (see the next page).
Clearance Adjustment
• Do this after the timing adjustment.
Standard: Within 0.80 +- 0.15 mm

• Front cover ( p.70 "Front Cover, Operation Panel")
1. Release the stopper at the operation side [A] from the pressure arm [B].
• Slide the stopper [A] to the left, and then lift the pressure arm [B].
2. Using a gap gauge, measure the clearance [C] between the drum surface and the exit pawls. It
should be 0.80 +-0.15 mm.
3. If the clearance is not correct, adjust the clearance by turning the bolt [D].
4. Lock the stopper on the operation side with the lock bracket to keep the press roller in its correct
position.
Air Pump Adjustment
Purpose: To ensure that the exit pawl produces a jet of air at the proper time.
139
• Rear covers ( p.74 "Rear Cover")

1. Check the recess in the drum drive gear meets the positioning hole [A] in the bracket, as shown.
2. Check whether the hole [B] in the pump drive gear is aligned with the hole [C] in the air pump unit
bracket.
3. If the alignment is incorrect, remove the air pump unit and re-position the gear.
140
Paper Delivery
Chocks
[A]: Chocks ( × 2)
141
[B]: Buffer fin bracket ( × 2 [C]) – Normally, do not disassemble parts [B] to [E] in the field.
[D]: Buffer fin
[E]: Buffer fin link
142
Network Printer Controller
Network Printer Controller

Printer Board
2. Remove the printer board with case. ( × 3, × 2, × 3).
143
3. Remove the printer board [A] from the case ( × 7, × 1).
• Remove the SD card [B] before you remove the printer board, if there is an SD card in the
board.
• When you replace the printer board, remove the NVRAM [C] from the old printer board and
install it on the new printer board. Otherwise, all the controller settings (such as the IP address)
will be lost.
144
Sound-proofing Cushions
The following are the attachment positions of the soundproofing cushions.
Paper Feed Left, Paper Feed Right
[A]: 10.0 mm to 12.0 mm

[B]: 0.0 mm
145
Paper Exit
[C]: 0.0 mm
Master Eject Cover
Master eject cover ( × 4)
146
[D]: 0.0mm to 2.0mm
Base
Paper delivery cover ( × 4) ( p.137 "Paper Delivery ")
• Insert the soundproofing cushion from the paper delivery side, and push it towards the inside of the
machine.
• The cushion has a short side and a long side, as shown above. Insert the cushion from the short
side, and secure the cushion inside the machine at [E].
• The soundproofing for the base does not have double-sided tape.
147
Fuse, LED, VR, DIP-SW, AND TP Tables

Blown Fuse Conditions
PSU
No. Rate Symptom
FU700 6.3 A The machine does not turn on
E-41 is displayed, and the output mode in SP mode does

FU701, 6.3 A
not turn anything on except the main motor.
E-12 is displayed, and the output mode in SP mode does

FU702 6.3 A
not turn anything on except the main motor.
FU703, 704 6.3 A E-06 is displayed.
LED’S
MPU
No. Function
Monitors the paper feed circuit in the MPU. Usually, this LED is
LED1
blinking at intervals of 2 seconds.
Monitors the OPU2:FPGA. Usually, this LED is blinking at intervals

LED2
of 1 second.
Monitors the CPU operation. Usually, this LED is blinking at

LED3
intervals of 1 second.
Monitors the master end sensor. When the sensor detects a master,
LED4
this LED is lit. ( p.113 "Master End Sensor Adjustment")
Monitors the master edge sensor. When the sensor detects a

LED5 master, this LED is lit. ( p.111 "Master Edge Sensor
Adjustment")
148
No. Function
Monitors the duct jam sensor. When the sensor detects a master,
LED6
this LED is lit. ( p.110 "Duct Jam Sensor Adjustment")
LED7 Not used.
Monitors the GATC2:FPGA. Usually, this LED is blinking at intervals

LED8
of 1 second.
Controller Board
No. Function
Monitor the CPU operation. This LED is blinking in the normal

LED1
condition.
VR’S
MPU
No. Function
VR101 Adjusts the master end sensor ( p.113 "Master End Sensor Adjustment")
VR102 Adjusts the duct jam sensor ( p.110 "Duct Jam Sensor Adjustment")
VR103 Adjusts the master edge sensor ( p.111 "Master Edge Sensor Adjustment")
VR104 Adjusts the 2nd drum master sensor ( p.112 "2nd Drum Master Sensor Adjustment")
PSU
No. Function
RV1 Adjusts the thermal head voltage. ( p.114 "Thermal Head Voltage Adjustment")
149
Ink detection board
No. Function
VR1 Adjustment for the ink detection. ( p.129 "Ink Pump Adjustment")
Dip Switches
Ink detection board
No. Normal drum Color drum A4 black drum
SW1 OFF OFF ON
SW2 OFF ON OFF
SW3 OFF OFF OFF
SW4 OFF OFF OFF
Controller Board
SW2 OFF ON
1 ROM boot SD card boot
2 Normal machine operation Boot only ROM monitor
3 Not used Not used
4 Not used Not used
Number SW Setting
When the main switch is turned on while pushing SW3, the

SW3 Push Switch
controller board will go to the detailed self-check mode.
150
Test Points
MPU
No. Function
TP101 Measures the master end sensor voltage. ( p.113 "Master End Sensor Adjustment")
TP102 Measures the duct jam sensor voltage. ( p.110 "Duct Jam Sensor Adjustment")
Measures the master edge sensor voltage. ( p.111 "Master Edge Sensor
TP103
Adjustment")
Measures the 2nd drum master sensor voltage. ( p.112 "2nd Drum Master Sensor
TP104
Adjustment")
PSU
No. Function
TP701 Measures the thermal head voltage. ( p.114 "Thermal Head Voltage
TP702 Adjustment")
151
152
Service Program Mode
• Make sure that the data-in LED ( ) is not on before you go into the SP mode. This LED indicates
that some data is coming to the machine. When the LED is on, wait for the copier to process the
data.
Using Service Program Modes
Use the service program modes (SP modes) to check electrical data, change operating modes, and
adjust values.
• The Service Program Mode is for use by service representatives only so that they can properly
maintain product quality. If this mode is used by anyone other than service representatives for any
reason, data might be deleted or settings might be changed. In such case, product quality cannot
be guaranteed any more.
How to Select a Program Number
1. Using the number keys [A] or the keys [B] or the zoom keys [C], enter the desired main menu
number (listed below), then press the Enter key [D] or the OK key [E].
Main menu number list:
1. Copy data, 2. Basic settings, 3. System settings, 4. Input mode
153
5. Output mode, 6. Adjustment, 7. Memory clear, 8. System test

2. Using the number keys or the keys or the zoom keys, enter the desired sub-menu number, then
press the Enter key or the OK key.
3. Enter the desired value or mode using the number keys (SP modes are listed in the service program
tables).
• Use the Memory/Class [F] key to toggle between “+” and “-“.
• To enter a decimal place, you do not have to enter a decimal point. For example, to enter
“1.5” just press “1“ and “5“ keys.
4. Press the Enter key or the OK key to store the displayed setting.
5. Follow the “Change Adjustment Values or Modes” procedure below.
• To cancel the SP mode, press the Clear Modes/Energy Saver key [G] or the Cancel key [H]
154
6. Troubleshooting
Firmware Update
To update the firmware for the machine, you must have the new version of the firmware.
There are three types of firmware: Main, ADF and controller (FV-Lt).
Type of Firmware
There are two types of main firmware. One type is for A3 models, and the other is for B4 models.
Download the firmware that corresponds to the model you are using.
Type of firmware Function Location of firmware
Main firmware (A3 model) Engine Main board (MPU)
Main firmware (B4 model) Engine Main board (MPU)
ADF firmware Engine Main board (MPU)
Controller (FV-Lt) firmware Printer Controller Printer board
Before You Begin
An SD card is a precision device. Always observe the following precautions when you handle SD cards:
• Always switch the machine off before you insert an SD card. Never insert the SD card into the slot
with the power on.
• Do not remove the SD card from the slot after the power has been switched on.
• Never switch the machine off while the firmware is downloading from the SD card.
• Keep SD cards in a safe location where they are not exposed to high temperature, high humidity,
or exposure to direct sunlight.
• Always handle SD cards with care. Do not bend or scratch them. Do not let the SD card get
exposed to shock or vibration.
• Make sure that the write protection of an SD card is unlocked when you download an application
to it.
Keep the following points in mind when you use the firmware update software:
• “Download” means to send data from the SD card to the machine.
155
6. Troubleshooting
• Make sure that the machine is disconnected from the network to prevent a print job for arriving
while the firmware update is in progress before you start the firmware update procedure.
Preparing To Download Firmware
1. Create a folder named “romdata” on the SD card (this step is only necessary when the SD
card is used for the first time).
2. Create one of the following folders inside the “romdata” folder. Make sure to create the
correct folder for the model you are using.
Main or ADF
• A3 model: “C279” folder
• B4 model: “C277” folder
Controller(FV-Lt)
• “C654” folder
• The SD card can be shared with other files (firmware for other duplicators, MFPs, etc.).
• The speed of displaying the right firmware on the operation panel will slow down if there are
many files in the SD card.
3. Store the firmware in the “C279” ,“C277”,or “C654” folder.
File storage location
Type of firmware File name File storage location
Main firmware (A3) C279****X_#_sd.bin /romdata/C279
Main firmware (B4) C276****X_#_sd.bin /romdata/C277
ADF (A3) /romdata/C279

D5785390X.fwu
ADF (B4) /romdata/C277
Controller(FV-Lt) C654****X_#_sd.bin /romdata/C654
***: Part number X: suffix #: version No.

4. Wait until the data is transferred completely.
• Do not remove the SD card from the PC until after all data is transferred (at this time, the PC
says that it is safe to remove the card).
156
Firmware Update
5. Compare the size of the file on the PC and the file on the SD card. If the sizes are different,
the data was not transferred completely.
• Do not take out the SD card until after you turn off the PC or disconnect the USB Reader/
Writer.
Download Main/ADF firmware
Updates the main firmware using an SD card.
1. Before downloading new firmware, check the firmware version number(Main) with
SP1-70 or file suffix number (ADF) with SP 1-78 ( Appendices - Main SP Tables).
2. Prepare an SD card with the latest firmware.
3. Turn off the main switch and disconnect the power cord.
4. Remove the rear card cover.

5. Plug the SD card into the connector on the MPU.
6. Connect the power cord, then turn on the main switch.
7. Access SP8-1(ADF: SP8-2) and press the OK key. Press the “Enter(#)” key.
8. Press the Enter key. (It takes about 2.0 minutes to complete.)
9. Check that “Completed” is displayed.
10. Turn off the main switch, and remove the SD card.
157
6. Troubleshooting
11. After downloading the firmware, turn on the main power and enter SP mode to confirm
that the download is complete.
Download FV-Lt firmware
1. Before downloading new firmware, check the firmware version number with SP9-5 (
Appendices - Main SP Tables).
2. Turn off the main switch.
3. Rear Cover. ( p.74 "Rear Cover")

4. Put the SD card in the slot of the ACU board.
5. Turn on the main switch again.
158
Firmware Update
6. Enter the SP mode (SP9-40: Load Program – System).
On the left [B], you can see the firmware version that is now in the machine.
On the right [C], you can see the firmware version on the SD card.
More than one version can be stored on the card. Use the Image Chg button “ ” to select the
version that you want to download.
After selecting, push the ‘#’ button to start downloading.
The approximate downloading time is 10 minutes.
• The number of “ ” signs [D] increases during the downloading.

• If the downloading did not finish correctly, an error message will be shown on the operation
panel.
• If an error occurred during the download, do the download again when the display panel
shows the SP mode screen. If this is not possible, the ACU board (Printer controller board)
must be replaced.
7. Turn off the main switch after the operation panel changes from “Executing” to
“Completed”.
8. Take out the SD card if you finished downloading.
159
6. Troubleshooting
9. After downloading the firmware, turn on the main power and enter SP mode to confirm
that the download is complete.
• Do not insert or extract the SD card when the machine power is on.
• Do not shut off the power when the firmware is downloading.
160
Electrical Component Defects

Jams which occur because of a sensor error are shown below.
error jam
Paper feed error “A” jam
Drum error “B” jam
Paper Exit error “C” jam
2nd drum error “D” jam
Eject Box error “E” jam
ADF error “P” jam
Sensors
Component Condition Symptom
Master Eject Position (HP) Sensor Open E-23 is displayed whenever the drum rotates.
Shorted
Paper Exit Timing Sensor Open E-21 is displayed whenever the drum rotates.
Shorted
Feed Start Timing Sensor Open E-24 is displayed whenever the drum rotates.
Shorted
161
6. Troubleshooting
2nd Feed Timing Sensor Open E-22 is displayed whenever the drum rotates.
Shorted
No display even if the drum is extracted and

Connect E-06 is displayed when printing or master
Drum Sensor (connecter) making.
“No drum” is displayed when initialization is

OPEN
finished.
The print images blur because the ink pump is

ON
not ON.
“Ink end” is displayed when printing or master

Drum Ink Sensor (Detection pin) making, and cannot be canceled. No Ink LED is
on.
OFF
Ink leak occurs in the drum because ink supply is
performed every time the door is door opened
and closed.
E-17 is displayed whenever the start button is

Shorted
Drum Ink Temperature Sensor pushed.
(Harness) Wire E-18 is displayed whenever the start button is
Snapping pushed.
Pressure Plate Limit Sensor Open “Master eject is full” is displayed.
Shorted E-12 is displayed.
Pressure Plate HP Sensor Open E-12 is displayed when the pressure plate is
activated.
Shorted
Drum Master Sensor There is a The master eject does not occur and the “D” jam
master on indicator is lit whenever a master is made.
the drum.
The “No master” indicator is not lit if there is no

master.
No master The “B” jam indicator is lit and is not cancelled
when a master is not on the drum and master
making is started.
162
2nd Feed Sensor reflected The “C” jam indicator is lit.

light / There
is a paper
The “B” jam indicator is lit whenever a copy is

No paper
made.
Master Eject Sensor Open The “B” jam indicator is lit.
Shorted The “BE” jam indicator is lit.
Clamper Open Sensor E-00 is displayed whenever the clamper

Open
operates.
Shorted E-00 is displayed
Clamper Close Sensor Open E-00 is displayed
E-00 is displayed whenever the clamper

Shorted
operates.
Table Lower Sensor The paper table goes down below the sensor,
Open
and E-02 is displayed.
Shorted The paper table doesn’t go down.
Platen Cover Sensor The image is treated using center/edge erase

Open
mode.
The master is made normally if the Start button is

Shorted
pushed twice.
Reflected If paper which should not be detected by the

light sensor is set, it will be detected.
Original Length Sensor Depending on the set paper when a master is

No made in this state, there may be a size
reflected disagreement warning, auto rotation or
light Reduce/Enlarge.
Scanner HP Sensor Open E-13 is displayed when scanner HP is running.
E-13 is displayed when the start button is

Shorted
pushed and the scanner returns to HP.
163
6. Troubleshooting
Original Length / Width Sensor ON The correct original size is undetectable if

original does not match the sensor pattern of the
original size.
Depending on the set paper when a master is
OFF made in this state, there may be a size
disagreement warning, auto rotation or
Reduce/Enlarge
Master Set Cover Sensor The “D” jam indicator is lit and cannot be
Open
canceled.
The “D” jam indicator is lit when the Master Set

Shorted
Cover is open.
Master End Sensor The “D” jam indicator is lit when there is no
There is a master. The Jam LED is on. Cannot detect Master
master on End. Roll-up jam, image, solid image, dirty press
the drum. roller occurred when the master was torn off the
master roll and it was twisted around the drum.
The “load new master roll” indicator is lit and

No master
the “load new master roll” LED is on.
Paper Height Sensor The paper table goes up over the sensor, and
Open
E-02 is displayed
The “A” jam indicator is lit whenever a copy is

Shorted
made.
Registration Sensor reflected The “A”,”B” jam indicator is lit and cannot be
light / There canceled.
is a paper
The “A” jam indicator is lit whenever a copy is

No paper
made.
Paper End Sensor reflected Printing can begin even if there is no paper, but
light / There the “A” jam indicator will be lit.
is a paper
The “load more paper” indicator is lit. The paper

No paper table moves down to the lower position, if it is
not at the lower position.
164
Cutter HP Sensor ON E-01 is displayed.
OFF
ON The correct paper size is undetectable if paper

does not match the paper size sensor pattern.
A size different from the set paper or "*" is
Paper Size Sensor
OFF displayed.
When a master is made in this state, there may
be a size disagreement warning or solid image.
Paper Length Sensor If paper which should not be detected by the

sensor is set, it is detected, and a size different
Reflected from the set paper is displayed.
light
The press roller becomes dirty whenever the
paper is shorter than the image.
If the paper detected by the sensor is set, it will

not be detected, and a size different from the set
No paper paper is displayed.
length Long images will be cut because the machine
does not detect the presence of long paper sizes
on the table.
ON E-41 is displayed.
Ink Idling Roller HP Sensor
OFF
Printing Pressure HP Sensor Open E-43 is displayed.
Shorted
Reflected
Even if a clamp error occurs, the Master Push
light / There
Mylar is pressed and becomes dirty. The “D”
is a master
2nd Drum Master Sensor jam indicator is lit.
on the drum.
The Master Push Mylar is not pressed. Cut errors

No master
cannot be detected.
165
6. Troubleshooting
Duct Jam Sensor There is a The “D” jam indicator is lit.

master on
the drum.
There is a master in the lower master tray, but

the duct jam sensor does not detect a master, the
No master
master vacuum fans do not pull the master, and
E-01 is displayed.
Duct Plate HP sensor ON E-42 is displayed.
OFF
Master Edge Sensor There is a The “D” jam indicator is lit.

master on
the drum.
No master
Thermal Head HP Sensor increase the E-47 is displayed.

pressure
release the
pressure

Open
pushed.
Thermal Head Temperature Sensor
Shorted
pushed.
The original is fed even if the ADF does not

have an original. Therefore the “P” jam
Open indicator is lit
The Jam LED is ON. The machine cannot shift to
the energy-saving mode at the correct time.
ADF Original Detection
The Platen Cover is scanned even if the ADF
has an original
Shorted Even if the original is set in the ADF in energy-
saving mode, it cannot return from energy-
saving mode.
166
ON:
reflected The “P” jam indicator is lit.
light
ADF Skew Correction
OFF: No
The “P” jam indicator is lit when paper is fed-in
reflected
from ADF.
light
ON:
light
ADF Registration
OFF: No
reflected
from ADF.
light
ON:
light
ADF Org Exit
OFF: No
reflected
from ADF.
light
Open The “close the ADF cover” indicator is lit.

ADF Org Feed Cover The original is fed, even if the ADF cover is
Shorted
open. Therefore the “P” jam indicator is lit
The Platen Cover is read even if the ADF has an

Open
original and the ADF is not lifted.
ADF Lift Up
The original is fed, even if the ADF cover is
Shorted
open. Therefore the “P” jam indicator is lit
167
6. Troubleshooting
Switches
Front Door Safety Switch The “open cover” indicator is lit. The “open
Open
cover” LED is on.
Main unit error (“A”,”B”,”C” jam and No ink)

cannot be canceled.
Drum information is not updated even if drums
are exchanged with the main switch on.
Close
An SC occurs if you make a master.
The Interlock SW (door cover side) is OFF when
the door cover is open, and an SC will occur
when a master is made.
Main Switch OFF The machine does not turn on.
The machine does not turn off.

ON E-61 is displayed when you shut off the
machine.
Master Making Unit Set Switch The “Lower Master Tray is Open” indicator is lit;
Connect even though, the master making unit is not set.
Cannot be canceled.
The “No Master Making Unit” indicators are lit

Open
and cannot be canceled.
Eject Box Set Switch The master is fed to the eject box, even if there is
ON
no eject box.
The “No eject box” indicators are lit and cannot

OFF
be canceled.
Master making begins, but the lower master tray

ON is open, the master vacuum fans do not pull the
Lower Master Tray Set Switch master, and E-01 is displayed.
OFF The “Lower Master Tray is Open” indicator is lit.
168
Can operate the Vacuum fan, clamper, Blower

ON fan motor, Eject roller, Pressure plate and drum
if there is no Eject box.
Interlock Switch
An SC is displayed for the clamper, pressure
OFF plate, or drum when the main switch is turned
on.
Power Supplies
+5v (CN102-4) No supply The machine does not turn on.
+5v (CN102-2, 3) No supply The machine does not turn on, but LED103 on
the MPU blinks.
+12v (CN102-9) No supply Black stripes in the image.
-12v (CN102-8) No supply The LCD/LEDs on the operation panel do not

indicate.
+24v (CN111-3, 4, 5, 6) No supply E-47 is displayed, and the output mode in SP

mode does not turn anything on except the
main motor.
+24v (CN111-1) No supply E-12 is displayed, and SP5-13, 14, 15 (master

eject motor/ pressure plate motor output mode)
do not turn the motor on.
Motor drive board FUSE FUSE The “open cover” indicator is lit.
FU700(PSU) FUSE The machine does not turn on.
E-41 is displayed, and the output mode in SP

FU701 (PSU) FUSE mode does not turn anything on except the
main motor.
E-12 is displayed, and the output mode in SP

FU702(PSU) FUSE mode does not turn anything on except the
main motor.
FU703,FU704(PSU) FUSE E-06 is displayed.
169
6. Troubleshooting
Controller
CPU Count Registration Error CPU error
Cashless error
TLB error
ASIC DMA error ASIC error
Timer error
Registration error
SDRAM ROM monitor usage area error RAM error
1 bit shift error
All area error
SSCG ACK error ASIC error
NVARM ROM monitor using area error NVRAM error
All area error
NIC NIC error NIC error
Interrupt ASIC interrupt registration check CPU error

error
ROM ROM monitor CRC error ROM error
Kernel CRC error
ROMFSCRC error
170
7. Energy Saving
Energy Save
Energy Save
Customers should use energy saver modes properly, to save energy and protect the environment.
The area shaded grey in this diagram represents the amount of energy that is saved when the timers are
at the default settings. If the timers are changed, then the energy saved will be different. For example, if
the timers are all set to 120 min., the grey area will disappear, and no energy is saved before 120 min.
expires.
Timer Settings
The user can set these timers with User Tools (System settings)
• Energy saver timer (1 – 120 min): Low Power Mode. Default setting: 1 minute
• Auto off timer (1 – 120 min): Off
Default settings:
C279 1min.
• The energy saver timer and the auto off timer cannot be used at the same time. Only one is
available.
Recommendation
We recommend that the default settings should be kept.
171
7. Energy Saving
• If the customer requests that these settings should be changed, please explain that their energy
costs could increase, and that they should consider the effects on the environment of extra energy
use.
• If it is necessary to change the settings, please try to make sure that the Auto Off timer is not too
long. Try with a shorter setting first, such as 30 min., then go to a longer one (such as 60 min.) if the
customer is not satisfied.
• If the timers are all set to the maximum value, the machine will not begin saving energy until 120
minutes has expired after the last job. This means that after the customer has finished using the
machine for the day, energy will be consumed that could otherwise be saved.
172
Paper Save
Paper Save
Effectiveness of the Combine Function
The combine function reduces the amount of paper used. This means that less energy overall is used for
paper production, which improves the environment.
Combine mode
Reduce paper volume in half!
Recommendation
Please explain the above features to the customers, so that they can reduce their paper usage.
C279
The following table shows paper savings and how the counters increase for some simple examples of
single-sided jobs.
If combine mode is used, the total counters work in the same way as explained previously. The following
table shows paper savings and how the counters increase for some simple examples of combine jobs.
Originals Simplex Sheet used Paper Saved
1 2 0
1 2 1
173
MEMO
176 EN
Model PD-D1
Machine Code: C279
Appendices
3 February, 2012
TABLE OF CONTENTS
1. Appendix: General Specifications
Specifications......................................................................................................................................................3
Main frame.....................................................................................................................................................3
Supported Paper Sizes..................................................................................................................................6
Paper Feed (mainly Europe and Asia).................................................................................................6
Paper Feed (mainly North America)....................................................................................................7
Software Accessories.....................................................................................................................................8
Printer Drivers.........................................................................................................................................8
Utility Software.......................................................................................................................................8
Optional Equipment.......................................................................................................................................9
Auto Document Feeder.........................................................................................................................9
Tape Dispenser......................................................................................................................................9
Network Printer Controller (Printer Unit Type 4545A).....................................................................10
2. Appendix: PM Tables
PM Tables.........................................................................................................................................................11
Other Yield Parts..........................................................................................................................................12
ADF (D578).........................................................................................................................................13
3. Appendix: Service Call Conditions
Service Call Conditions...................................................................................................................................15
Service Call..................................................................................................................................................15
Program Download Error Codes................................................................................................................19
4. Appendix: Service Program Mode Tables
SP Table............................................................................................................................................................21
Service Program Mode...............................................................................................................................21
Reading SP mode tables.....................................................................................................................21
SP mode tables.............................................................................................................................................21
1
2
Specifications
Main frame
Configuration: Stand-alone
Digital with 400 dpi thermal head

Master Process:
(Fine mode: 400 × 600 dpi)
Scanning (Pixel 600 × 400 dpi

Density): (Fine mode: 600 × 600 dpi)
Originals: Sheet/Book
Printing process: Fully automatic one-drum stencil system
Original Size: Maximum 297 × 432 mm / 11.7" × 17.0"
Maximum: 297 × 432 mm / 11.7" × 17.0"

Copy Paper Size:
Minimum: 70 × 148 mm / 2.8" × 5.8"
Copy Paper Weight: 47.1 – 209.3 g/m2, 12.5 – 55.6 lb.
A3 drum: 290 × 410 mm / 11.4" × 16.1"

Printing Area: B4 drum: 251 × 355 mm/ 9.9" × 14"
A4 black drum: 200 × 290 mm / 7.9" × 11.4"
60, 75, 90, 105, 130 sheets/minute (5 steps)
Printing Speed: *A6 SEF, A5 LEF, and indeterminate forms (length of

170 mm or less) can be processed at rates of 60, 75,
90, and 105 sheets/minute.
65 masters (A3, B4 drum)

Master Eject Box
70 masters (A4 drum)
Capacity:
*Normal conditions
3
3 enlargements and 4 reductions
A3 version DLT version
141% 155%
Enlargement 122% 129%
115% 121%
Reproduction Ratios:
Full Size 100% 100%
93% 93%
87% 77%
Reduction
82% 74%
71% 65%
Zoom: 50 to 200%, in 1% steps
America: 120 V, 60 Hz
Power Source:
Europe, Asia: 220 – 240 V, 50/60 Hz
Noise Emission
Operating Position Sound Power

Sound Power Level
Level
Not more than 45 dB

Standby: Not more than 31 dB (A)
(A)
Copying 60 Not more than 73 dB

Not more than 59 dB (A)
rpm: (A)
Copying 90 Not more than 76 dB

rpm: (A)
Copying 130 Not more than 81.5

rpm: dB (A)
• The above measurements were made in accordance with ISO 7779 standard.
4
Specifications
Tables closed: 805 × 705 × 638 mm (31.7" × 27.8" × 25.1")

Tables opened: 1370 × 705 × 638 mm (53.9" × 27.8" × 25.1")
Dimensions (W x D x H)
• Measurement Conditions
• 1) Without the ADF
• 2) Without the table
America, Europe, Asia (Except for Chinese Version): 87 kg (191.8

lb)
Weight:
China: 89 kg (196.21 lb)
(Excluding ADF, platen cover, ink, and master)
Less than 23 seconds (A4 copying)

Less than 27 seconds (A3 copying)
Less than 26 seconds (B4 machine)
Less than 24 seconds (B4 machine-A4 copying)
Master Process Time:
• Measurement Conditions
1. 100% size
2. Normal mode (Not fine mode)
Paper Table Capacity: 1,000 sheets (64 g/m2, 17 lb)
Paper Delivery Table Capacity: 1,000 sheets (64 g/m2, 17 lb)
Leading Edge Margin: 5 ± 3 mm
Trailing Edge Margin: 2 mm
Side Registration Adjustable

± 10 mm
Range:
Vertical Registration Adjustable

± 15 mm
Range:
5
Thermal master roll type:

320 mm width, 110 m/roll (A3 master roll)
280 mm width, 110 m/roll (B4 master roll)
Yield:
Master Type:
200 masters/roll (A3 Drum)
220 master/roll (B4 Drum)
315 masters/roll (A4 Drum)
Maximum run length per master: 4,000 prints
Temperature: 0 to 40 °C
Humidity: 10 to 95% RH
Master Storage Conditions: Recommended maximum storage period: One year after
production date
Note: Avoid locations exposed to direct sunlight.
600 ml cartridge type
Ink Type: Available colors: Black, Red, Blue, Green, Brown, Purple, Yellow,
Navy, Maroon, Orange, Teal, Gray, Reflex blue, Hunter green,
Burgundy, and Violet
Temperature: -5 to 40 °C (Optimal conditions: 15 to 25 °C)

Humidity: 10 to 95% RH (Optimal conditions: 20 to 70% RH)
Ink Storage Conditions: Recommended maximum storage period: 18 months after
production date
Note: Avoid locations exposed to direct sunlight.
Supported Paper Sizes
Paper Feed (mainly Europe and Asia)
Size
Paper sizes
(W × L)
A3 SEF 297 × 420 mm
B4 JIS SEF
257 × 364 mm
(Japanese Industrial Standard)
6
Specifications
Size
Paper sizes
(W × L)
A4 LEF 297 × 210 mm
A4 SEF 210 × 297 mm
B5 JIS LEF 257 × 184 mm
B5 JIS SEF 184 × 257 mm
A5 SEF 148 × 210 mm
B6 JIS SEF 128 × 182 mm
A6 SEF 105 × 148 mm
F LEF 13" × 8"
Vertical: 148 - 432 mm,

Others
Horizontal: 70 - 297 mm
Paper Feed (mainly North America)
Size
Paper sizes
(W x L)
Ledger 17" × 11"
Legal LEF 14" × 8.5"
Letter LEF 11" × 8.5"
Letter SEF 8.5" × 11"
Half Letter LEF 8.5" × 5.5"
Half Letter SEF 5.5" × 8.5"
Vertical: 5.8" - 17",

Others
Horizontal: 2.8" - 11.7"
7
Software Accessories
The printer drivers and utility software are provided.
Printer Drivers
The following OS are supported (Only 32 bit)

• Windows XP Professional Edition (*)
• Windows XP Home Edition
• Windows 2003 Server Standard Edition (*)
• Windows 2003 Web Edition (*)
• Windows 2003 R2 (*)
• Windows Vista Home Basic
• Windows Vista Home Premium
• Windows Vista Home Enterprise (*)
• Windows Vista Home Ultimate (*)
• Windows Server 2008 (*)
• Windows Server 2008 R2 (*)
• Windows 7 Starter
• Windows 7 Home Premium
• Windows 7 Professional
• Windows 7 Ultimate
(*)Exclude Cluster and Terminal
Utility Software
Software Description
• Switch to / come out of Energy Saver mode

• Monitor multiple printers in use / Create groups
Smart Device Monitor
• Display the printer status / settings
for Admin
• Make printer settings
• Check print job histories of documents identified by user codes
8
Specifications
Software Description
• Display the printer status / settings

• Check print job status and history, or deleting the print job
Web Image Monitor • Make printer settings
• Network protocol settings
• Security settings
• Peer-to-Peer print function

Desktop Binder – Smart • Display an error / a completion message
Device Monitor • Monitor multiple printers in use
• Display up to 100 print jobs
Optional Equipment
Auto Document Feeder
Size A3 to A5, DLT to HLT

Paper Size/Weight:
Weight 40 to 128 g/m2 (10 to 34 lb.)
Table Capacity: 50 sheets (80 g/m2, 20 lb)
Power Consumption: 50W
Power Source DC24V±10%, DC5V±5%, DC5VE±5% From mainframe
Dimensions (W x D x H): 550 × 496 × 120 mm (21.7" × 19.5" × 4.7")
Weight: 10 kg (22 lb.)
Tape Dispenser
250 mm
Tape feed length
9.8 inch
100 mm/s
Tape feed speed
3.9 inch/s
9
Power Consumption 15W
Power Source From mainframe
155 × 105 × 60mm

Dimension(WxDxH)
6.1" × 4.1" × 2.4"
700 g
Weight
1.5lb
Network Printer Controller (Printer Unit Type 4545A)
Printer language RPCS
Host interface USB 2.0
Network interface 100Base-TX/10Base-T
Protocol TCP/IP
Engine interface LUVI
On board memory 64MB
Optional PostScript Not available
Supported resolutions 400 dpi
Job history check By user ID identified on printer driver
Web Image Monitor Available
10
PM Tables
The following items should be maintained periodically. There are two sets of intervals - one based on
time and the other based on print count. For maintenance items with entries in both of them, use
whichever comes first.
C: Clean, R: Replace, L: Lubricate
Time
Interval
Print Any EM NOTE
Item 6M 1Y
Counter time
Scanner
Exposure Glass C C C Dry Cloth
Exposure Lamp Dry Cloth
Master Feed
Thermal Head C Cloth and alcohol
Cutter Unit
Original Feed Roller
Platen Roller C Damp cloth (water) and dry cloth
Drum Master Sensor C Damp cloth (water) and dry cloth
Drum
Ink container cradle C Damp cloth (water) and dry cloth
Drum Master Sensor C Dry cloth
Drum Master Sensor

C C C Dry cloth
Black Decal
Ink Roller One-way

clutch
Drum Removable Gear L
11
Time
Interval
Print Any EM NOTE
Item 6M 1Y
Counter time
Paper Feed
Feed Start Timing

C C Alcohol and dry cloth
Sensor
Registration Roller C C Alcohol and dry cloth
Separation Pad C C/R 1200k Alcohol and dry cloth
Paper Table C C C Alcohol and dry cloth
Paper Pick-up Roller/

C C/R 1200k C Dry cloth
Paper Feed Roller [A]
Paper Exit
Paper Exit Sensor C C Dry cloth
Printing Pressure
Damp cloth (water) and dry cloth

Press Roller (R) 1200k C (R): If continuously printing the
same small size
Drive Unit
Drum Drive Gears L
Other Yield Parts
The parts mentioned in these tables have a target yield. However, the total copy/print volume made by
the machine will not reach the target yield within the machine’s targeted lifetime if the machine is used
under the target usage conditions (ACV, color ratio, P/J, and C/O). So, these parts are categorized not
as PM parts but as yield parts (EM parts).
12
PM Tables
ADF (D578)
80K
Item EM NOTE
(Original)
Pick-up Roller C R Clean with water
Feed Belt C R Clean with water
Separation Roller C R Clean with water
Other Rollers C C Clean with water
Gears L Lubricate, if necessary
Platen Sheet C C Clean with water or alcohol
13
14
Service Call Conditions

Service Call
No. Symptom Possible cause
E-00 Clamper error Clamper drive

The MPU cannot detect the clamper position sensor signal Clamper sensors
(open or closed) within 3.0 seconds after the clamper motor Clamper motor
turns on.
E-01 Cutter error Cutter drive

The cutter HP sensor does not turn on within 3.0 seconds after Cutter switch
the cutter motor turns on. Cutter motor
E-02 Paper Table Drive error Table Drive

The paper height sensor or the table lower limit sensor does Table motor
not turn on within 7.5 seconds after the table motor turn on. Table height sensor
Table lower sensor
E-04 Thermal Head Overheat Overheat (wait for the

The temperature of the thermal head is grater than 54C when thermal head to cool
the Start key is pressed. down)
Thermal head
E-06 Main Motor error Main motor drive

The CPU cannot detect the master eject position sensor (drum Main motor
HP) signal within 5.0 seconds after the main motor turn on. Motor drive board
Master eject position
sensor
E-09 Thermal Head Thermistor Open Thermal head thermistor

The thermistor output voltage is over 2.82 volts. Thermal head connector
15
E-10 Thermal Head Energy Pulse error Thermal head connector

The CPU detects an abnormal ID signal from the thermal head Thermal head
energy control pulse. MPU
E-12 Pressure Plate error Pressure plate drive

The pressure plate home position sensor signal is not detected Pressure plate motor
within 6.0 seconds after the pressure plate motor turn on. Plate position sensors
E-13 Scanner error Scanner drive

The scanner HP sensor does not turn on within 15.0 seconds Scanner HP sensor
after the main switch turns on. Scanner motor
On the Initial Movement, the Scanner HP sensor does not turn
off when the scanner moves 22.2 mm towards the scanning
position.
On the Initial Movement, the scanner HP sensor does not turn
on within 2.0 seconds after the main switch turns on.
E-14 SBU Error SBU

SBU errors are most often caused by a SBU element or lamp
that is in poor condition.
E-17 Drum Thermistor Open Thermistor connector

The thermistor output voltage is over 2.67 volts. Thermistor
E-18 Drum Overheat Drum overheat

The temperature of the drum is greater than 54C when the Thermistor
Start key is pressed.
E-21 Paper Exit Timing Sensor error Drum sensors

The paper exit timing sensor does not activate before the Feeler
master eject position sensor activates.
E-22 2nd Feed Timing Sensor error Drum sensors

The 2nd feed timing sensor does not activate before the paper Feeler
exit timing sensor activates.
E-23 Master Eject Position Sensor (Drum HP) error Drum sensors
The master eject position sensor does not activate before the Feeler
feed start timing sensor activates.
16
E-24 Feed Start Timing Sensor error Drum sensors

The feed start timing sensor does not activate before the 2nd Feeler
feed timing sensor activates.
E-40 Thermal Head ID error Thermal head

The CPU detects an abnormal ID signal from the thermal head. MPU
Thermal head connector
disconnected
E-41 Ink Idling roller HP sensor remains on or off Idling roller HP sensor
The idling roller HP sensor does not change status within 4.0 Ink idling motor
seconds after the idling roller motor on signal is generated.
E-42 Duct plate error Duct plate HP sensor

The duct plate HP sensor does not change status within 4.0 Duct plate motor
seconds after the duct plate motor on signal is generated.
E-43 Printing Pressure error Printing pressure HP sensor

The printing pressure HP sensor does not change status within Printing pressure motor
4.0 seconds after the printing pressure motor on signal is
generated.
E-44 MSU error MPU

When error signal is received from the MPU board.
E-47 Thermal head driving error Thermal head HP sensor

The thermal head HP sensor does not change status within 4.0 Thermal head driving motor
seconds after the thermal head driving motor on signal is
generated.
E-50 Insufficient NVRAM data NVRAM (MPU)

The data in the NVRAM is not the expected data for this
machine (version update error)
E-51 Flash ROM error Flash ROM (MPU)

Data cannot process correctly when the firmware is
downloaded or an original is stored in the machine.
17
E-52 Registration motor Drive IC error Registration motor

If the Driver IC detects an over-current or overheating MPU
condition, the machine outputs the FAULT signal.
If the FAULT signal is detected, this SC appears on the display.
If the same SC repeatedly appears on the display, the Driver
IC may be damaged.
E-53 Paper feed motor Paper feed motor

If the Driver IC detects an over-current or overheating MPU
condition, the machine outputs the FAULT signal.
If the FAULT signal is detected, this SC appears on the display.
If the same SC repeatedly appears on the display, the Driver
IC may be damaged.
E-54 Ri2000A Configuration error MPU

Turn on the Main switch, come out of Enegry Saving
E-55 GATC2 (FPGA) Configuration error MPU
E-56 GATC2 (FPGA) Configuration writing error MPU

*See: Error Code
(Display:E42)
E-61 Auto Off Switch error Auto off switch

The main switch does not turn off for more than 6.0 seconds. Auto off switch connector
disconnected
E-70 DF Gate network error Network

10 seconds have passed since the original moved from the
registration position, but the DF gate signal has not turned on.
Note: DF gate has nothing to do with the DF (document feeder)
E-71 DF connect error Harness

ADF model code that is different from the code for this machine Main board
is received."
(*) OPU2 (FPGA) Configuration error MPU

Configuration does not end normally when the main switch is
turned on.
18
(*)When this error occurs, the Energy Saving mode LED blinks at intervals of 0.1 seconds. An error code
is not displayed.
Program Download Error Codes
Display Symptom Possible cause
E24 SD Card Access error. 1. Re-insert the SD card

2. Replace the SD card
E35 Does not match the module.
E36 Other reasons, the module does not exist. Rewrite the correct ROM data in the
SD card.
E40 Engine download execution failure(main) Replace the MPU
E41 Engine download execution failure(sub) Replace the MPU
E42 Engine download execution failure Replace the MPU

(FPGA Configuration error)
19
20
4. Appendix: Service Program Mode
Tables
SP Table
Service Program Mode
Reading SP mode tables
SP table reads as follows.
SP name
SP No
Detailed explanation of SP No.
Branch Menu item Category* [Max to Min / Default / variation]

number Detailed explanation of branch number.
• "Categories" on the right of the asterisk (*) SP have been described, the settings are stored in
NVRAM.
• "SP name" and "Menu item" after the (SSP) SP has been described as the super-service mode is SP.
SP mode tables
Copy data
1
Display data log such as number of prepress numbers and printing.
1-1 Total master counter
1-20 Total print counter
1-21 C/O 1
1-22 C/O 2 to 3
1-23 C/O 4 to 5
21
1-24 C/O 6 to 10
1-25 C/O 11 to 20
1-26 C/O 21 to 50
1-27 C/O 51 to 70
1-28 C/O 71 to 100
1-29 C/O 101 to 200
1-30 C/O 201 to 500
1-31 C/O 501 to 1000
1-32 C/O 1001 to 2000
1-33 C/O 2001 to 3000
1-34 C/O 3001 to 4000
1-35 C/O 4001 to
D - master clamp jam

1-50
Display frequency and incidence.
E - master eject jam

1-51
E - master compressing jam

1-52
A - paper non-feed jam

1-53
A - paper registration jam

1-54
B - paper wrapping jam

1-55
22
SP Table
C - paper delivery jam

1-56
P - original feed-in jam

1-57
Display frequency and incidence.(Using ADF)
P - original feed-out jam

1-58
Display frequency and incidence.(Using ADF)
D - master feed jam

1-59
D - master cut jam

1-60
D - mater duct jam

1-61
Main firmware part number

1-70
Displays the main firmware parts number and the suffix.
1-72 Serial number
1-73 Main firmware version
1-75 Serial number (Factory)
1-78 ADF ROM part number
Error code history

1-80
Displays the latest 40 SC codes. Use the key to view the records.
1-81 Telephone number display
23
SBU hard error location display
This function shows where a SBU error has occurred.

• bit 7: 0 (not used)
• bit 5: GASBU-N Id error
1-83
• bit 4: VSP5100 reset error
• bit 3: GASBU-N reset error
• bit 2: Serial communication error
• bit 1: Power ON/reset clear error
• bit 0: Connect detection error
1-84 SBU adjust error location display

• bit 5: Re error (Gain error)
• bit 4: Ro error (Gain error)
• bit 3: Ge error (Gain error)
• bit 2: Go error (Gain error)
• bit 1: Be error (Gain error)
• bit 0: Bo error (Gain error)
SBU level error location display
• bit 15: Ge error(Lamp error) • bit 7: 0 (not used)

• bit 14: Go error (Lamp error) • bit 6: 0 (not used)
1-85 • bit 13: 0 (not used) • bit 5: 0 (not used)

• bit 12: 0 (not used) • bit 4: 0 (not used)
• bit 11: 0 (not used) • bit 3: Ge error (White level error)
• bit 10: 0 (not used) • bit 2: Go error (White level error)
• bit 9: Ge error (Black level error) • bit 1: 0 (not used)
• bit 8: Go error (Black level error) • bit 0: 0 (not used)
24
SP Table
1-160 Not used
1-161 Key counter setting check
1-162 Key card setting check
Basic setting
2
Set the initial value of printing speed, ink detection, and international machine settings.
Default print speed [1 to 5 / 3 / 1]
Set the initial value of printing speed when you turn on and mode clear.
• 1: 1st Point(60rpm)
2-1 • 2: 2nd Point(75rpm)
• 3: 3rd Point(90rpm)
• 4: 4th Point(105rpm)
• 5: 5th Point(130rpm)
Default image position [-15.0 to 15.0 / 0.0 / 0.1 mm]

2-2
Set the initial value of "top-and-bottom position" when you turn on and mode clear.
Destination code [0 to 9,- / - / -]

2-4
Set the Destination code.
2-5 Not used [0 to 2 / 0 / -]
Image position display [0 to 2 / 1 / 1]
When the user moves the image position on the operation panel, this SP controls the length
of time that the adjustment value is shown on the display before the screen goes back to the
previous display.
2-6
'Slow' means that the display is shown for the longest time possible.
• 0:SLOW(1.5 seconds)
• 1:NORMAL (1.0 second)
• 2:FAST(0.5 second)
25
Vendor Selection [*1 / *2 / Ricoh]
Brands depend on the destination.

*1 Displays only brand that can be set.
2-7
RICOH / TTEC / KMBJ / NRG / Nashuatec /RexRotary / Gestetner / Lanier / Savin /
Standard
*2 If the model code has not been set, if there are multiple brands of a single model code,
"RICOH" has been set.
Ink detection board [ ON-OFF / ON / -]
Sets whether to detect the ink in the drum.

2-10 • ON: Detect the ink.
• OFF: The ink is considered always exist.
("OFF" is used in the test or if the ink be removed from the drum..)
Paper end sensor [ ON-OFF / ON / -]
Set whether to detect the presence of the paper.

2-11
• ON: Detect the presence of the paper.
• OFF: The paper is considered always exist.(Used in the test)
Drum master sensor [ ON-OFF / ON / -]
Set whether to detect the presence of the drum master.

2-12
• ON: Detect the presence of the drum master.
• OFF: The drum master is considered always exist.(Used in the test)
Platen cover sensor [ ON-OFF / ON / -]
Set whether to detect the presence of the platen cover.

2-13
• ON: Detect the presence of the platen cover.
• OFF: The platen cover is considered always exist.(Used in the test)
Paper length sensor [ ON-OFF / ON / -]
Set whether to detect the presence of the paper length sensor on the master feed unit.
2-15 • ON: Detect the presence of the paper length sensor.
• Always assumed to be the largest(mm:420mm, inch:432mm).
(Used in the test)
26
SP Table
2-21 Ink setting [0 to 1 / 0 / 1]
Double count-up (A3) [0 to 2 / 0 / 1]
When using A3 Drum, electromagnetic counter (master, paper) count up every 2 / print.
2-22 • 0: As usual, one count increase.
• 1: Two counts increase only master. Paper increase one count.
• 2: Two counts increase both master and the paper.
Key card count setting [0 to 2 / 0 / 1]
This function is used to specify the number of sheets to be printed per Key Card counter
count.
2-23
• 0:Master
• 1:Only Print number(Master revision)
• 2: Only Print number(Number conversion)
Key card master count conv. [0 to 20 / 1 / 1Print]
This function is valid only if the key card count setting is 1.

2-24
Example: If this SP is set to 20 (in other words, if you decide that the cost of one master is
20 times the cost of one print), every time one master is made, the print count increases by
20.
Key card print count setting [0 to 3 / 1 / 1Print]
2-25 This function is valid only if the key card count setting is 2.
The number of sheets to be printed per print counter count.
Idling after less than 3 prints [YES - NO / NO / -]
Ensures that the first print has sufficient ink density if the machine was not used for a long
time. Also, when the customer continuously prints small numbers (1 to 3 prints), ink leaks
2-28 occur from the trailing edge of the drum.
When SP 2-38 is on, the idling roller motor turns to press the drum idling roller against the
inner surface of the drum screen after printing. Then, the idling motor turns to remove the ink
leaks. The idling motor action depends on the settings of SP 2-28 and 2-29.
27
Idling after how many prints [1 to 5 / 3 / 1 Print]
2-29 • If SP 2-28 is set to 'YES', the idling motor turns if 3 or more prints were made.
• If SP 2-28 is set to 'NO', the idling motor turns if the number of prints made is the same
as or more than the setting of SP 2-29.
2-31 Ink Auxiliary Supply [0:After 1:Before 2:No / 0:After / - ]
Ink supply after trial [ ON-OFF / OFF / -]

2-32
Ink is detected and supplied after the trial print when this SP is on.
Re-Feeding setting [ ON-OFF / ON / -]
When the machine performs re-feeding, the paper registration position can be up to 5mm
out of range. If this position is not acceptable to the customer, change this SP mode to
2-33
"OFF".
• ON: Re-feeding is on (factory setting).
• OFF: Re-feeding is off.
Slow starting mode [30rpm / 45rpm / 45rpm /-]
Increase the image density of trial prints.

The figures below are drum-rotating speeds. A setting of "30rpm" will increase the image
density of trial prints.
This mode was added because trial print images are lighter than with other models.
<30rpm> <45rpm>
2-34 • Trial Print: 30rpm • Trial Print: 45rpm
• 1st Print: 45rpm • 1st Print: 60rpm
• 2nd Print: 60rpm • 2nd Print: 75rpm
• 3rd Print: 75rpm • 3rd Print: 90rpm
• 4th Print: 90rpm • 4th Print: 105rpm
Print pressure fixing mode [ON - OFF / ON / -]
This function is used to specify whether the print pressure point is set to automatic or fixed.
2-35 • Auto: Decide on Sp6-70 to 87
• Fixed: Decide on SP2-36
SP2-37setting is not reflected.
28
SP Table
2-36 Print pressure in fixing mode [1 to 5 / 4 / 1]
When the print pressure point for SP2-35 is set to fixed, this field is used to specify the value
at which it is fixed.
2-37 Printing pressure adjust [-2 to 2 / 0 / 1]
Changes the printing pressure of all printing speeds (60 to 130 rpm).
When you adjust printing pressure for each printing speed or temperature, use SP6-70 to
87.
2-38 Ink idling roller setting [0 to 2 / 1 / 1]
Ensures that the first print has sufficient ink density if the machine was not used for a long
time.
The idling roller motor turns to press the drum idling roller against the inner surface of the
drum screen.
• 0: OFF
• 1: The machine enters the drum idling mode after the master is ejected.
• 2: The machine enters the drum idling mode after the master is made.
Paper delivery motor speed [-55 to 55% / 0 / 1%]

2-39
Feeding 15rpm,30rpm,45rpm will only affect.
Idling after print [ ON-OFF / ON / -]
Set whether to detect the idling after printing

2-40
• ON: To the idling(To press the idling roller)
• OFF: Don't idling(Not to press the idling roller)
T/H control by temp: color [ ON-OFF / ON / -]
Set the ink temperature compensation when use color ink.

2-41
whether to detect the idling after printing
• OFF: Temperature inside the drum takes a constant value irrespective.
T/H control by temp: black [ ON-OFF / ON / -]
2-42 Set the ink temperature compensation when use black ink.
29
T/H energy control [0 to 50% / 7 / 1%]

2-43 The default is 7%. This means that during normal printing mode, the thermal head energy is
93% of the maximum possible (100 – 7).
T/H energy control - eco [0 to 50% / 15 / 1%]
2-44 The default is 10%. This means that in economy printing mode, the thermal head energy is
reduced by another 10%. With the default settings, this means that the thermal head energy
is 83% of maximum power (100-7-10).
T/H control by temp: A4 [ ON-OFF / ON / -]
2-45 Set the ink temperature correction in the A4 drum.
T/H energy control: A4 drum [0 to 50% / 12 / 1%]

2-46 Initial value is 12%.In this case, that means thermal head energy can be up to 88% in
printing mode (100-12=88%).
T/H energy control: A4 eco [0 to 50% / 15 / 1%]
2-47 Initial value is 15%.In this case, in economy printing mode (A4) means that an additional
15% reduction will be thermal head energy. Thermal head energy in 78% maximum.
(100-7-15=78%)
T/H swinging mode [ ON-OFF / OFF / -]
2-50 Sets whether to enable the shift of the thermal head writing position.
• ON: Shift the values specified in the SP2-51(T/H swinging quantity).
T/H swinging quantity [±1 to 5mm / 2 / -]

2-51
Set the shift amount of the thermal head writing position.
T/H Control by Temp: Color (Fine) [ ON-OFF / ON / -]
2-52 Set the ink temperature correction in the color ink density mode.
T/H Control by Temp: Black (Fine) [ ON-OFF / ON / -]
2-53 Set the ink temperature correction in the black ink density mode.
30
SP Table
T/H Energy Control: (Fine) [ 0 to 50% / 7 / 1%-]

2-54 Initial value is 7%.In this case, that means thermal head energy can be up to 93% in printing
mode(density) (100-7=93%).
T/H Energy Control -Eco (Fine) [0 to 50 / 15 / 1%]
2-55 Initial value is 15%.In this case, in economy printing mode (density) means that an
additional 15% reduction will be thermal head energy. Thermal head energy in 78%
maximum. (100-7-15=78%)
T/H Control by temp: A4 (Fine) [ ON-OFF / ON / -]
2-56 Set the ink temperature correction in the A4 drum density mode.
T/H Energy Control: A4 (Fine) [0 to 50 / 7 / 1%]

2-57 Initial value is 7%.In this case, that means thermal head energy can be up to 93% in printing
mode(A4 density) (100-7=93%).
T/H Energy Control: Eco: A4 (Fine) [0 to 50 / 15 / 1%]
2-58 Initial value is 15%.In this case, in economy printing mode (A4 density) means that an
additional 15% reduction will be thermal head energy. Thermal head energy in 78%
maximum. (100-7-15=78%)
Bold letter mode [ ON-OFF / OFF / -]

2-60
Makes a bold outline of a letter-mode image.
Scanning shade on margin adj [0 to 1 / 0 / 1]
This function specifies whether to remove shades from the original when scanning.
2-61 • 0: If an original is scanned while it is being pressed, This produces the same level of
image quality as when the predecessor unit is used.
• 1: If an original is scanned while it is not being pressed, shades are output. This
produces the same level of image quality as when the predecessor unit is used.
31
Paper table standby pos [fall slightly/ normal / normal / -]
High: The paper table after printing is moved to a higher position than the standard
position. This will reduce the time for starting the first print when continuously making
masters.
Low: The standard position
2-95 If SP2-95 is "high", the machine goes to the standard position in the following situations.
• When the master end indicator lights and a message is displayed
• When a master eject jam (B jam location indicator) is displayed
• When a master feed jam (D jam location indicator) is displayed
• When the paper height sensor is actuated immediately after the main switch is turned
on.
2-100 Master making without printing [ ON-OFF / OFF / -]
This function wraps a blank master around the drum. The ink on the drum may dry up at the
following times:
• The machine is not used for a long time.
• The customer changes to a color drum that has not been used recently.
This might affect the print quality (Poor image: ghost image of the previous print).
Wrap a blank master around the drum after you print, to prevent ghost images of previous
prints when the machine is not used for a long time.
1. Access SP2-100 (Make master without printing). Then press "OK".
2. Press the "Start" key while holding down the "#" key.
Drum Master Out&wrap Setting [ ON-OFF / OFF / -]
This function allows users to remove and wrap the master on the drum. The following
keypad operations become available.
2-101 Remove: Press the "Reset key" for more than three seconds
Wrap: Press the "Master Making" key while pressing the "#" key.
Do not leave the drum without a master for more than a day, or the surface of the drum will
become dry.
Set whether to detect the presence of the master feed time.

• OFF: Master feed time is invalid
• ON: Master feed time is enable.
32
SP Table
2-115 Reg Improvement for 1st Prt [ ON-OFF / OFF / -]
2-120 Master Compression Time - A3 [ 0-3 / 0 / -]
2-121 Master Compression Time - B4 [ 0-3 / 0 / -]
2-122 Master Compression Time - A$ [ 0-3 / 0 / -]
5th Speed Paper Limit [ ON-OFF / OFF / -]
This function is used to suppress printing at the 5th speed if the feed direction length of the
paper is less than 170 mm.
2-130 • ON: Suppress printing at the 5th speed if the feed direction length of the paper is less
than 170 mm.
• OFF: Don't suppress at the 5th speed by the paper size. The accuracy of the image is
degraded.
System settings
3
Set the time, key card/key counter settings.
33
Input the present time [yy.mm.dd hh.mm.ss / - / -]
Input the year, the month / date, and the time in the following order. Press the Enter (#) key
between each one.
1. Input the last two digits of the present year (two-digit number).
2. Input the present month (two-digit number).
3. Input the present date (two-digit number).
4. Input the present hour (two-digit number).
5. Input the present minute (two-digit number).
3-1
6. Input the present second (two-digit number).
Example: 2003/January/27th/13:00:00
1. Input 03 then press Enter (#).
6. Input 00 then press OK
Input Tel number [0 to 9(19-digit) / 0 / -]

3-2
Input the phone number to display when service call
Input serial number [0 to 9, A to Z(19-digit) / 0 / -]
Input the machine number.

3-3 • 0 to 9: Numeric key
• A to Z: Print speed key
• - :Memory/Class key
34
SP Table
Input installation date [yy.mm.dd / 00.1.1 / -]
Input the installation date as shown below. Press the Enter (#) key between each one.
1. Input the last two digits of the present year (two-digit number).
2. Input the present month (two-digit number).
3-4 3. Input the present date (two-digit number).
Example: 2003/January/27th/13:00:00
3. Input 27 then press OK
3-9 Key counter setting [ YES - NO / NO / -]
Set whether connect the key counter.
Key card setting [ YES - NO / NO / -]

3-10
Set whether connect the key card.
Input mode
4
Checks the input of sensors.
4-1 Scanner HP sensor
4-2 Platen cover sensor
4-3 Original Length Sensor1
4-4 Original Length Sensor2
4-5 Thermal head HP sensor
4-6 Master making unit set SW
4-7 Master set cover sensor
4-8 Cutter HP switch
4-9 Master end sensor
4-10 Master edge sensor
35
4-11 Duct plate HP sensor
4-12 Lower master tray switch
4-13 Duct jam sensor
4-14 Eject box set switch
4-15 Master eject sensor
4-16 Pressure plate HP sensor
4-17 Pressure plate limit SN
4-18 Ink detection signal
4-19 Color drum signal
4-20 A4 drum signal
4-21 Drum set signal
4-22 Clamper open sensor
4-23 Clamper close sensor
4-24 Drum master sensor
4-25 Master eject position SN
4-26 Paper exit timing sensor
4-27 Printing pressure HP sensor
4-28 2nd drum master sensor
4-30 Table lowering switch
4-31 Table lower sensor
4-32 Paper height sensor
4-33 Paper end sensor
4-34 Paper length sensor
4-35 Paper width signal 0
36
SP Table
4-41 Registration sensor
4-42 Feed start timing sensor
4-43 2nd feed timing sensor
4-44 Paper exit sensor
4-50 Door safety sensor
4-51 Main motor error signal
4-70 Key counter signal
4-71 Key card signal
4-90 Ink idling roller HP sensor
4-91 Ink temperature
4-120 ADF Original Length 1 (B5)
4-121 ADF Original Length 2 (A4)
4-122 ADF Original Length 3 (LG)
4-123 ADF Original Width S
4-124 ADF Original Width M
4-125 ADF Original Width L
4-126 ADF Original Width LL
4-127 ADF Original Detection
4-128 ADF Rear Edge Detection
37
4-129 ADF Skew Correction
4-130 ADF Registration
4-131 ADF Org Exit
4-132 ADF Org Feed Cover
4-133 ADF Lift Up
Output mode
5 Checks the output of motors.

Check the output of the selected operation is performed while pressing the Start key.
5-1 Exposure lamp (xenon lamp)
5-2 Scanner motor - scan
5-3 Scanner motor - return
5-4 Scanner to HP
5-5 Duct plate motor - close
5-6 Duct plate motor - open
5-7 Duct plate motor: to HP
5-8 Duct fan motor
5-9 Blower fan motor
5-10 Master feed motor-Forward
5-11 Master feed motor Backward
5-12 VHD signal
5-13 Cutter motor - forward
5-14 Cutter motor - reverse
5-15 Master re-setting
5-16 Master push Mylar - push
5-17 Master push Mylar - free
38
SP Table
5-18 T/H driving motor - up
5-19 T/H driving motor - down
5-20 Master eject motor
5-21 Pressure plate motor:limit
5-22 Pressure plate motor:to HP
5-23 Main motor: 15 rpm
5-31 Main motor to HP
5-32 Main motor to Master clamp
5-33 Clamper motor: to open
5-34 Clamper motor: to close
5-35 Ink pump motor
5-36 Pressure release solenoids
5-37 Ink idling motor
5-38 Ink idling roller: down
5-39 Ink idling roller: up
5-40 Table motor - down
5-41 Table motor - up
39
5-42 Paper feed motor: 15 rpm
5-50 Registration motor: 15 rpm
5-56 Registration motor: 105rpm
5-57 Registration motor: 130rpm
5-58 Air knife fan motors
5-59 Vacuum fan motor
5-60 Paper delivery motor - low
5-61 Paper delivery motor - middle
5-62 Paper delivery motor - high
5-63 Paper counter
5-64 Master counter
5-65 Key counter signal
40
SP Table
5-66 Key card signal
5-80 Printing pressure motor HP
5-81 Move to pressure 1
5-82 Move to pressure 2 (HP)
5-100 All indicators on the panel
5-101 Drum Home Position LED
5-111 Auto OFF solenoid
5-120 ADF Feed Motor Forward
5-121 ADF Feed Motor Reverse
5-122 ADF Transfer Motor Forward
5-123 ADF Transfer Motor Reverse
5-124 ADF Feed Clutch
5-125 ADF Feed Solenoid
5-126 ADF Reverse Solenoid
5-128 ADF FGATE ON
Adjustment
6
Adjust the threshold and operation of the sensors.
Main-scan position -platen [-5.0 to 2.0 mm / 0.0 / 0.1mm]

6-1
Adjust the image position of the scanner to the main scanning direction.
41
Main-scan position - ADF [-5.0 to 5.0 mm / 0.0 / 0.1mm]
Adjust the image position of the ADF to the main scanning direction.
Main Scan Position - Platen, ADF
6-2 2. Measure the difference between the center of the main-scan on the original and on the
print.
3. Access SP6-01, input the gap value and press the Enter key. (If you input a positive
value, the image moves towards the operation side.)
5. Make a copy in ADF mode and repeat the process using SP6-02.
Scan start position-platen [-2.0 to 5.0 mm / 1.0 / 0.1mm]

6-3
Adjust the scan start position of the scanner.
Scan start position - ADF [-5.0 to 5.0 mm / 0.0 / 0.1mm]

6-4
Adjust the scan start position of the ADF
1. Make copies of the test pattern printed during the previous adjustments ( previous
page), in platen mode at 90 rpm (speed 3). Use the 10th print for the adjustment.
3. If it is not, calculate the reproduction ratio using the following formula.{(130 -
Value) / 130} x 100 = ± X.X % (Round off to one decimal place) Example: If the
value is 133, {(130 - 133) / 130} x 100 = - 2.3 %
Scanning speed - platen [-5.0 to 5.0 % / 0.5 / 0.1%]

6-5
Adjust the scanning speed of the scanner.
6-6 Scanning speed - ADF mode [-5.0 to 5.0 % / 0.0 / 0.1%]
42
SP Table
Adjust the scanning speed of the ADF.

Scanning speed (platen/ADF)
1. Make copies of the test pattern printed during the previous adjustments ( previous
page), in platen mode at 90 rpm (speed 3). Use the 10th print for the adjustment.
Value) / 130} x 100 = ± X.X % (Round off to one decimal place) Example: If the
value is 133, {(130 - 133) / 130} x 100 = - 2.3 %
Skew Correction - ADF [-5.0 to 5.0 mm / 0.0 / 0.1mm]

6-7
Adjust the skew correction of the ADF.
Scale shadow mask -platen [2.0 to 10.0 mm / 2.0 / 0.1mm]

6-8
Adjust the scale shadow mask of the scanner.
Master writing speed [-5.0 to 5.0 % / -0.4 / 0.1%]
1. Input SP8-10 (Test patterns) and enter "6", then press the Start key.
2. Exit the SP mode, then print 10 copies at 90 rpm (speed 3). Use the 10th print for the
adjustment.
3. The length of the 8 squares in the feed direction should be 130 mm, as shown above.
6-10
Value) / 130} x 100 = ± X.X % (Round off to one decimal place)
6. Repeat the procedure to make sure that the ratio is correct.
Master writing length [-5.0 to 5.0 % / 0.0 / 0.1%]

6-11
Adjust the whiting length of the master making unit.
43
Registration buckle 60 to 105rpm [0 to 100 / 18 / PLS]
Adjust the flexible volume of the paper feed. The larger the number, the greater the amount
6-12 of deflection flexible volume.
• ON: Detection of the ADF.
• OFF: The ADF is considered always exist.(Used in the test)
Registration buckle 130rpm [0 to 100 / 1 / PLS]
Adjust the flexible volume of the paper feed. The larger the number, the greater the amount
6-13 of deflection flexible volume.
• ON: Detection of the ADF.
• OFF: Always be considered the maximum. (Used in the test)
6-14 Paper regist position 60rpm [-5.0 to 5.0mm / 1.0 / 0.5mm]
Paper regist position adjusting of the use of adjusted values 60rpm (Preliminary).
1. The space between the leading edge and the next line should be 8 mm.If you have
missed, access SP mode, and adjust within the range of ± 5.0mm displacement
minutes.
Example: If the value is 16mm, 16-8=8
2. Exit the SP mode. Reproduct and check the test patterns(SP8-10 "6" cross") again
Assist pulse 130rpm [1 to 120PLS / 80 / PLS]
Adjust the number of the assist pulse.

6-19
When paper registration is not good, then adjust this.
The larger the number, the greater the amount of paper feed motor feed.
Standard white execution
Adjust the standard white execution.

6-20
Press the Enter key to start the adjustment.
Results after adjustment (success / failure) are displayed.
44
SP Table
Standard white confirmation
Check the adjustment of the standard white execution.

6-21
Press the Enter key to start the check.
Results after adjustment (success / failure) are displayed.
Standard white adjusted value [-128 to 127PLS / 0 / -]
6-22 Display/Change the standard white adjusted value.
Display the adjustment results to the range of failure (-512 to 511).
6-23 Master making density-Pencil
6-24 Master making density-Tint
6-25 Master making density-Photo [0 to 2 / 1 / -]
6-26 Master making density-LtrPht
6-27 Master making density-Letter
6-28 MTF filter - Letter:M [0 to 7 / 1 / -]
6-29 MTF filter - Letter:S [0 to 7 / 1 / -]
6-30 MTF filter -Letter/Photo:M [0 to 7 / 4 / -]
6-31 MTF filter -Letter/Photo:S [0 to 7 / 4 / -]
6-32 MTF filter - Photo:M [0 to 7 / 1 / -]
6-33 MTF filter - Photo:S [0 to 7 / 1 / -]
45
Sharpens the image, but moiré can become more apparent.

Refer to the following table for the relationship between this SP mode value and filter
strength (the relationship is not linear).
• 0:*0
• 1:*1/32
• 2:*1/16
• 3:* 1/8
• 4:* 1/4
• 5:* 1/2
• 6:* 2
• 7:* 4
Ink detection adjustment
With no ink drum, the drum and adjust VR to adjust the display to be 6.7(6.7us).
When the drum has ink inside, the machine displays "----".
• Before running this mode, please wipe off the ink around the ink roller.
• Before attempting this procedure, wipe off the ink around the ink roller. To do this, set
• SP2-10 (ink detection) to OFF, and feed paper until ink ends.
• After finishing the procedure, do not forget to return SP2-10 to the default (ink
detection on)
6-40
Access SP6-40, and open the door cover. Then turn VR1 on the ink detection board until
the display becomes "3.0 u" (3 us).
46
SP Table
6-50 Master end sensor voltage [0.5 to 3.5 / 1.90 / V]
6-51 Master edge sensor voltage [1.5 to 3.5 / 2.80 / V]
6-52 Duct jam sensor voltage [0.5 to 3.5 / 2.00 / V]
6-53 2nd drum master sensor voltage [0.5 to 3.5 / 1.00 / V]
Master returning value [0 to 200 / 100 / 0.1mm]
The auto adjustable master set mechanism automatically moves the leading edge of the
master to the correct position after the user installs a master roll.
6-60 This position can be adjusted with SP 6-60. This SP adjusts the amount that the machine
feeds the master after it detects the leading edge of the master.
Bigger number: increases feeding
Smaller number: decreases feeding
6-61 Master length - A3 drum [4200 to 6000 / 5400 / 0.1mm]
6-63 Master length - A4 drum [3000 to 6000 / 3400 / 0.1mm]
Master pushing value [0 to 100 / 50 / pulse]
This adjusts the pressure between the master push Mylar and the drum.
6-64
Bigger number: increases the pressure
Smaller number: decreases the pressure
6-70 Trial pressure:low temp [1 to 5 / 2 / -]
6-71 60 rpm pressure:low temp [1 to 5 / 1 / -]
6-74 105rpm pressure:low temp [1 to 5 / 5 / -]
6-75 130rpm pressure:low temp [1 to 5 / 5 / -]
Adjust the pressure each print speed in low temperature (below 15 °C).
6-76 Trial pressure:normal temp [1 to 5 / 2 / -]
47
6-77 60rpm pressure:normal temp [1 to 5 / 1 / -]
Adjust the pressure each print speed in normal temperature (15 to 28 °C).
6-82 Trial pressure:high temp [1 to 5 / 2 / -]
6-83 60 rpm pressure:high temp [1 to 5 / 1 / -]
6-86 105rpm pressure:high temp [1 to 5 / 3 / -]
6-87 130rpm pressure:high temp [1 to 5 / 5 / -]
Adjust the pressure each print speed in high temperature (over 28 °C).
6-90 Analog Gain Adjustment:RED [0 to 7 / 0 / -]
6-91 Analog Gain Adjustment:GREEN [0 to 7 / 0 / -]
6-92 Analog Gain Adjustment:BLUE [0 to 7 / 0 / -]
Display the SBU adjustment(AGC)result when turn on.
6-93 Digital Gain Adjustment:RE [0 to 1023 / 81 / -]
6-94 Digital Gain Adjustment:RO [0 to 1023 / 81 / -]
6-95 Digital Gain Adjustment:GE [0 to 1023 / 70 / -]
6-96 Digital Gain Adjustment:GO [0 to 1023 / 70 / -]
6-97 Digital Gain Adjustment:BE [0 to 1023 / 73 / -]
6-98 Digital Gain Adjustment:BO [0 to 1023 / 73 / -]
Display the SBU adjustment(AGC)result when turn on.
48
SP Table
6-100 Paper registration 15rpm

[-40 to 40 / 0 / pulse]
Paper registration
1. Set SP2-34 (Printing pressure adjust) to a value of "30 rpm" (print from 30 rpm).
2. Set SP8-10 (Test patterns) to a value of "6", then press the Start key.
3. Access SP4-91 (Ink temperature), and check the ink temperature.
4. Make 6 copies at speed 5 (finishing with 130 rpm). Perform the adjustment below for all 6
copies.
Trial print: 30 rpm -> 1st print: 45 rpm -> 2nd print: 60 rpm ->3rd print: 75 rpm
-> 4th print: 90 rpm -> 5th print: 105 rpm -> 6th print: 130 rpm
When the ink temperature is low (below 15 degrees) or high (28 degrees or above), you can
adjust the machine to make only 6 copies (change SP 8-23 to 'On'). Then, the 2nd print will not
be made, because it is the same speed as the first print.
Trial print: 30 rpm ->1st print: 45 rpm ->2nd print: 45 rpm ->3rd print: 60 rpm
->4th print: 75 rpm ->5th print: 90 rpm ->6th print: 105 rpm ->7th print: 130 rpm
5. The distance between the leading edge and first line should be 8mm, as shown below.
6. If this distance is not 8 mm, access SP6-101 to 107 and then input a value to adjust the distance
(range: -40 to 40, step: 1) for each of 6 copy samples.
The higher the value, the narrower the distance between the leading edge and 1st line becomes
(and vice-versa). Also, each step corresponds to approximately 0.58mm. Input the value that
will bring the distance to 8mm.
7. Perform the adjustment again for any of the samples that are still outside the 8mm standard.
8. Return SP2-34 (Printing pressure adjust) to the value it was at before the adjustment.
49
6-108 Paper Regist:skip:15rpm

[-40 to 40 / 0 / mm]
6-116 Paper middle bulge: 15rpm

[-100 to 100 / 0 / mm]
50
SP Table
Paper middle bulge
51
Adjusts doubled [A] or blurred [B] images (e.g. bold lines, text) for each printing speed (15, 30,
60,75, 90, 105, 130 rpm), by changing SP settings.
1. Set SP2-34 (Printing pressure adjust) to a value of "30 rpm" (print from 30rpm).
3. Access SP4-91 (Ink temperature), then check the ink temperature.
copies.
5. Check the area from the leading edge to about 50 to 200 mm down for any doubled or blurred
images.
6. If any are present, access SP6-117 to 123 and then input a value to adjust the doubled or
blurred images (range: -100 to 100, step: 1) for each of 6 copies samples
To adjust the distance for 30 cpm, use SP 6-117.
7. Perform the adjustment again where necessary.
52
SP Table
6-124 Paper front bulge: 15rpm

[-90 to 8 / 0 / mm]
Paper front bulge
53
1. Set SP2-34 (Printing pressure adjust) to a value of "30 rpm" (print from 30rpm).
3. Access SP4-91 (Ink temperature), then check the ink temperature.
copies.
5. Check the area from the leading edge to about 30mm down for any doubled or blurred images.
6. If any are present, access SP6-125 to 131 and then input a value to adjust the doubled or
blurred images (range: -90 to 8, step: 1) for each of 6 copies samples
Higher values ([C]): Blurred images improve, doubled images tend to be more noticeable.
Lower values ([D]): Doubled images improve, blurred images tend to be more noticeable.
7. Perform the adjustment again where necessary.
54
SP Table
6-132 Paper Regist:A4drum:15

[-40 to 40 / 0 / pulse]
6-140 Paper Regist:skip:A4:15

[-40 to 40 / 0 / pulse]
6-148 Paper middle bulge:A4:15

[-100 to 100 / 0 / mm]
55
6-156 Paper front bulge:A4:15

[-90 to 8 / 0 / mm]
Memory clear
7
Date clear and Initialization performs.
Factory settings clear
7-1 Done just prior to shipment from the factory.
Disappear while pressing the o key and # key pressing.
Total counter clear

7-3
Clear the total print counter of prepress numbers and printing numbers.
Jam/Error data clear
Clears all of the transport number of misses.

Regist jam(A)
7-4
Resist remainig jam(A+B)
Curling jam(B)
Eject jam(C)
Protect Code Clear
7-11 Default setting 5-7 "Default setting protect" Default: OFF
Default setting 5-8 "Protect password" Default: OFF
56
SP Table
System test
8
Program download test, Reproduction test pattern.
Download main firmware
8-1 Download the program from the SD card into the machine.
Start by pressing the "# "key.
8-2 Download DF firmware
Download the program from the SD card into the machine.
8-3 Report(LOG DATA/SC/JAM)
8-4 Report(BASIC SETTING
8-5 Report(ADJUSTMENT VALUES)
8-6 Report(INPUT/OUTPUT TESTS)
Test patterns [ 1 to 9 / 6 / 1]
Makes prints without using the scanner.

Access SP8-10 and select the number "6", then press the "Enter(#)" key.
8-10
Other numbers are as shown below, but do not use them except for number "6".
1: Grid, 2: Vertical, 3: Horizontal gray, 4: Vertical gray, 5: 16 grays,
6: Cross, 7: Diagonal grid, 8: 256 grays, 9: 64 grays
57
Temporary security off [ ON-OFF / OFF / -]
This function cancels "Security Mode" when the engineer repairs/inspects the machine.
The technician must cancel security mode in order to take out the drum.
It is not necessary to cancel security mode in order to make prints; put an original on the
exposure glass and make a new master. But if the customer does not want you to waste a
master, and is not concerned about security for the master on the drum, then you can cancel
security mode and make prints with the master that is on the drum.
When this SP8-18 is "ON", security mode is cancelled and the drum rotates to the home
position. You can pull the drum unit out of the machine. At this time, the display on the
8-18
operation panel is reversed (see the illustration below).
"Security Mode" is used to prevent others from accessing the master on the drum and
making prints of confidential documents.
When you set "Security Mode":
• You cannot press the "Proof" key or the "Start" key while the previous master is on the
drum.
• You cannot pull out the drum unit when the machine is in standby mode.
• Printing will not start until you set a new original and press the "Start" key.
• You cannot clear "Security Mode" by turning off the main switch.
Free run - ADF [50 to 200 / 100 / 1%]

8-19
Free running the ADF.
Free run - scanner [50 to 200 / 100 / 1%]

8-20
Free running the scanner.
Paper feed at 15 rpm [ ON-OFF / OFF / -]
Feeds paper at the lowest speed (15 rpm), and applies printing pressure.
1. Set a stack of paper on the paper feed table.
8-21 2. Access SP8-21 and press the OK key.
3. Exit the SP mode and enter the number of sheets that you want to feed.
4. Press the Start key.
5. To exit this mode, turn off the main switch.
58
SP Table
Free run-Paper feed(15rpm) [ ON-OFF / OFF / -]
Drives the paper feed mechanism at the lowest speed (15 rpm) without paper.
1. Access SP8-22 and press the OK key.
8-22 2. Exit the SP mode and enter the number of times that you want to repeat the paper feed
cycle.
3. Press the Start key.
To exit this mode, turn off the main switch.
30->45->60 rpm print mode [ ON-OFF / OFF / -]
8-23 This SP affects the operation of SP 6-100-107, SP 6-116-123, and SP 6-124-131, if the
temperature is low (below 15 degrees) or high (28 degrees or above).
SP 8-23 automatically goes back to 'Off' after you turn the main switch off/on.
8-30 All indicators on the panel
Perform all of the LED lights on the control panel.

All control panel lights up each time you press the Enter key.
Off when released.
8-31 LCD data download setting [ ON-OFF / OFF / -]
8-902 Download main firmware
Print controller
9
To set the printer controller.
[Normal-Hexdump-SDcard / Normal /
9-1 Output Data Print
-]
59
In normal operation, an image that is sent from the computer is printed out. But with this SP
mode, the
image is changed to hex data and then output on paper or to an SD card.
There are three settings:
• O: Normal (Default setting)
• 1: Hex Dump
• 2: SD card
Hex Dump
The image is changed to hex data, and the hex data is printed out on paper.
This mode continues until main power is shut off.
In some cases, there will be a large quantity of data, and many masters will be
consumed to print out the hex dump. Be careful when you use this mode.
SD Card
The image is changed to hex data, and the hex data is transferred to an SD card.
Procedure:
2. Put the SD card in the SD card slot.
3. Turn on the main switch.
4. Set SP 9-1 to "1: SD card" and get out from the SP mode.
5. Send the data from the computer
6. The 'data in' LED on the machine blinks during the data transfer, and the LED turns
off when the data transfer is finished (the transfer takes a few seconds).
7. Set SP 9-1 to "0: Normal".
9. Remove the SD card from the machine.
Do not take out the SD card before you turn off the main switch and set the SP Mode to
"Normal".
Service Summary Print

9-2
Print the summary service.
NIB Summary Print

9-3
Print the network information.
60
SP Table
Firmware part number

9-4
Display the firmware numbers on the operation panel.
Firmware version
9-5
Display the firmware versions on the operation panel.
Clear Printer setting

9-30
Initialization the printer system settings.
Clear NIB NVRAM setting

9-31
Initialization the NIB NVRAM setting.
Load Program - system

9-40
Select and run programs that can be downloaded from the SD card.
61
MEMO
64 EN

DD4450 Service Manual

Uploaded by

Copyright:

Available Formats

DD4450 Service Manual

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DD4450 Service Manual

Uploaded by

Copyright:

Available Formats

Model PD-D1

Machine Code: C279

Reference Material for Maintenance

Before Installation, Maintenance

Shipping and Moving the Machine

Installation, Disassembly and Adjustments

• Use only standard tools approved for machine maintenance.

• Before you begin a maintenance procedure:

Power Plug and Power Cord

After Installation, Servicing

Points to Confirm with Operators

Prevention of Physical Injury

Health Safety Conditions

Observance of Electrical Safety Standards

Safety and Ecological Notes for Disposal

• Dispose of replaced parts in accordance with local regulations.

The Aim of Anti-tip Components and Precautions

[A]: Short Edge Feed (SEF)

Electrical Component Layout

6 CCD and SBU Outputs a video signal to the MPU.

No. Component Function

30 Ink Detection Board Checks if there is ink in the drum.

36 Operation Panel Boards These boards control the operation panel.

37 Power Supply Unit (PSU) Provides dc power to the machine.

54 Main Motor Board Controls the main motor speed.

70 Lamp Stabilizer This supplies power to the exposure lamp.

5 Scanner Motor Drives the scanner.

23 Master Feed Motor Feeds the master to the drum.

24 Table Motor Raises and lowers the paper table.

28 Printing pressure motor Raises and lowers the pressure roller.

31 Ink Pump Motor Drives the ink pump.

46 Air Knife Fan Motor 1

Provides suction so that paper is held firmly on the

40 Paper Delivery Motor Feeds out the printed paper.

53 Pressure Plate Motor Raises and lowers the pressure plate.

57 Main Motor Rotates the drum.

No. Component Function

67 Clamper Motor Opens or closes the master clamper on the drum.

74 Cutter Motor Cuts the master.

81 Master Feed Motor Feeds the master to the drum.

84 Blower fan motor Provides air to separate the master.

Presses or releases the drum idling roller against the drum

96 Ink Pump Motor Drives the ink pump.

1 Scanner HP Sensor Detects when the image sensor is at home position.

Detects when the master making unit runs out of master

Detects when the paper table reaches the paper feed

21 Registration Sensor Detects paper approaching the registration roller.

26 2nd drum master sensor Detects if there is a master on the drum.

Detects when the printing pressure is at the home

No. Component Function

41 Master Eject Sensor Detects used master misfeeds.

42 Drum Master Sensor Detects if there is a master on the drum.

49 Paper Exit Sensor Detects paper misfeeds at the exit.

Determines the paper misfeed check timing at the paper

Master Eject Position (Drum HP)

65 Clamper Closed Sensor Detects if the clamper is in the closed position.

66 Clamper Open Sensor Detects if the clamper is in the open position.

73 Cutter HP Sensor Detects when the cutter is at the home position.

Detects when the master making unit runs out of master