Dbstar Arm9 Manual

LED Display Control System
User's Manual
Nanjing DBstar
Electronic Technology Co. Ltd.
March 15, 2010
Special instruction
instruction：
Thank you for your trust and support to our company. In order to
guarantee your use process smoothly, please read the technical
support manual before using the products.
Catalog
Chapter I Hardware of LED's control system ................... 6
system...................
Section I: Summarize..................................................... 6
1.1.1 Flow chart exlplanation of the fast
application of the synchronous system .................... 6
system....................
1.1.2 Type of DBT-Q2007 and DBT-Q2009 control
system ..........................................................................
system..........................................................................
..........................................................................12 12
Section II Review of the performance of
DBT-Q 2007/
DBT-Q2007/ DBT-Q
2007/DBT-Q
DBT-Q2009 2009 control system........................... 12
1.2.1 Function description ........................................
description........................................
........................................1212
1.2.2 Recognition of the DBT-Q2007 and
DBT-Q2009 hardware .............................................. 14
hardware..............................................
1.2.2.1 DBT-Q2007 full color sending card card........ 14
....14
1.2.2.2 DBT-Q2007\DBT-Q2009 receiving
board (HUB board) ........................................... 17
board)...........................................
1.2.2.3 DBT-Q2009 receiving card (HUB
board): ................................................................. 19
board):.................................................................
1.2.3 Recognition of the DBT-Q2007 and
DBT-Q2009 software .................................................
software.................................................
.................................................2020
1.2.4 Main performance index of the DBT-Q2009
receiving card .............................................................
card.............................................................
.............................................................3232
1.2.5 Error detection function ................................. 33
function.................................
Section III Temperature and humidity sensor... 41
1.3.1 The connection schematic diagram is as
follows: ........................................................................
follows:........................................................................
........................................................................41 41
1.3.2 The application of the sensor in DBT-Q2007
synchronous system .................................................. 41
system..................................................
1.3.3 Application of the brightness sensor in
DB
DBA-A- 9.0 asynchronous system
A-9.0 ................................
system................................
................................4242
1.3.4 The application of the brightness sensor in
DBA-7.0 asynchronous system ................................
system................................
................................4343
Section IV Power control board...................................44
1.4.1 Graphic of the real material is as follows: follows:... ... 44
1.4.2 2009 multifunctional board ............................
board............................
............................4545
Chapter II Asynchronous control System ............................
System............................
............................4949
Section I DBA-9.0 asynchronous control system .. 49
2.1.1 Hardware recognition ..................................... 49
recognition.....................................
2
2.1.2 Technical parameters ...................................... 51
parameters......................................
2.1.3 Introduction of the application method method.............. 52
Section II DBA-7.0 asynchronous control system .
62
2.2.1 Hardware recognition ..................................... 62
recognition.....................................
2.2.2 Function characteristic ................................... 62
characteristic...................................
2.2.3 Software introduction and application
explanation .................................................................
explanation.................................................................
.................................................................63 63
2.2.3.1 Software introduction ...........................
introduction...........................
...........................6363
2.2.3.2 Software application ............................. 64
application.............................
Section III Video processor........................................ 75
2.3.1 Points for attention for safety ........................ 75
safety........................
2.3.2 Hardware connection ......................................
connection......................................
......................................76 76
2.3.3 Schematic diagram of the system connection
77
2.3.4 Explanation of the keyboard key-press: key-press:...... ...... 77
2.3.5 Operation case ..................................................
case..................................................
..................................................82 82
Chapter III Multimedia program and playing ................ 84
playing................
Section I: Summarize................................................... 84
3.1.1 Function characteristic ................................... 84
characteristic...................................
3.1.2 Operating environment ...................................
environment...................................
...................................8484
Section II Installation and unloading.....................84
3.2.1 Installation ........................................................ 84
Installation........................................................
3.2.2 Unloading ..........................................................
Unloading..........................................................
..........................................................89 89
Section III Specific explanation for application 90
3.3.1 Program composition ......................................
composition......................................
......................................90 90
3.3.2 Introduction of the interface window window........... 90
...........
3.3.3 Function introduction ..................................... 92
introduction.....................................
3.3.3.1 Menu bar: including file, edit, play,
control, tool, document and help .................
help。................. 92
.................92
2.3.3.2 Tool bar ...............................................
bar...............................................
...............................................101101
Section IV Edition of the program materials....108
3.4.1 Operation of the project bar ........................
bar........................ 108
........................108
3.4.2 Adding program materials ............................
materials............................ 111
............................111
3.4.3 Introduction of the material property property................ 111
3.4.4 Illustrations with example ............................
example............................ 123
............................123
3.4.5 Subsequent explanation.....................................125
3
Section V How to play VCD/DVD/cd.................. 125
3.5.1 Direct playing ................................................. 125
playing.................................................
3.5.2 Playing in the program ................................. 126
program.................................
Section VI How to play video input ...................... 126
3.6.1 New-established program window ..............
window.............. 126
..............126
3.6.2 Setting the input window of the video ........ 127
video........
Section VII how to play slide ...................................... 128
3.7.1 Playing .............................................................
Playing.............................................................
.............................................................128 128
3.7.2 Stopping playing ............................................ 129
playing............................................
Section VIII How to play subti subtittle and
notification.................................................................................. 129
3.8.1 Opening the notification management
window ......................................................................
window......................................................................
......................................................................129 129
3.8.2 Setting notification management window window......130 130
3.8.3 Playing/stopping notification display ......... 130
display.........
Section IX Management of the sports score..........130
3.9.1 select the sports score ....................................
score....................................
....................................130 130
3.9.2 Setting the management of the sports score
131
3.9.3 Playing/stopping PE score ............................
score............................
............................132 132
Section X Schedule...................................................... 132
3.10.1 Opening timing instruction list ..................
list.................. 132
..................132
Section XI Network control..................................... 133
3.11.1 Management of the remote real-time display
screen .........................................................................
screen.........................................................................
.........................................................................133 133
Section XII Backstage playing ................................... 135
3.12.1 Starting the backstage playing .................. 135
playing..................
3.12.2 Canceling the backstage playing ...............
playing............... 135
...............135
Section XIII Multi-screen combination...............137
3.13.1 Entering the synchronization of the
multi-screen combination ...................................... 137
combination......................................
Section XIV Software setting .................................. 139
3.14.1 Opening the setting of the software option
139
Chapter IV Accessory ........................................................ 142
Accessory........................................................
Section I Setting of the common display card.. 142
4.1.1 ATI-AGP/PCI series display card ............... 142
card...............
4
4.1.2 NVDIA series of display cards .....................
cards..................... 143
.....................143
Section II manufacturing of the communication
line..................................................................................................146
4.2.1 Internationally standard type ......................
type......................
......................146146
4.2.2 Special explanation ........................................
explanation........................................
........................................148 148
Chapter V Common problems ..........................................
problems..........................................
..........................................150 150
Section I Synchronous control system................. 150
5.1.1 Interruption of the connection .....................
connection.....................
.....................150150
5.1.2 No-signal output .............................................
output.............................................
.............................................150 150
Section II Asynchronous control system ............. 150
5.2.1 Failure to start normally .............................. 150
normally..............................
5.2.2 Failure to send the content normally normally.......... .......... 151
..........151
5
Chapter I Hardware of LED's
control system
Section I: Summarize
1.1.1 Flow chart explanation of the fast application of the
synchronous system
◆ Schematic diagram of the connection of the outdoor synchronous
control system:
◆ Enter the control software:
6
◆ Specific description of the establishment of the dialogue box of the
LED control system:
7
◆ Setting part of the sending card
Screen display
[Screen display] Adjust the brightness of the screen and the scope is
1-256.
Position of picture
[Position picture] Adjust the mode of the display and select
according to the resolution of the display. The area where the content on
the display is appointed shall be displayed on the LED big screen.
[Screen rotation] The display content on the display will rotate on the
big screen of LED with the rotation angle 0℃, 90℃, 180℃ and 270℃
respectively.
[Schedule] time is appointed to carry out the corresponding operation.
◆ Setting part of the receiving card
Before entering the establishment of the receiving card, it is very
necessary to understand the different contents of the receiving setting
interface to make the operation more simple and convenient.
[Screen options] The basic parameter of the monolithic receiving card
shall be established.
[LED driver] The driving chip type of the LED screen that the
receiving card is equipped with. The main supported driving chip types:
MBI5026/TB62726, MBI5027, MBI5030, MBI5039, 74HC595,
LPD6803, DM413, MBI5042 and MBI5020.
[Frame synchronized mode] can
make the computer and the LED display screen own the same refresh
rate.
[Dat
[Data a clock frequency] CLK of the driving chip of the driving screen,
the scope is 4-225, that means the frequency scope of the clock is
8
490KHZ-31.25MHZ.
[Data clock duty cycle] Means the data clock duty cycle of the clock
when displacement is carried out and higher clock of the scanning
displacement can be realized by changing this data. It is usually set as
50%.
[Gray scale levels] Generally speaking, the display screen of the
double color selects 256. 4096 grade is selected indoors while 16,384
grade is selected outdoors. The grades are 4, 8, 16, 32, 64, 128, 256,
512, 1024, 2048, 4096, 8192, 16384, 32768 and 65536 respectively.
[Gray effect] Changes the lays of graphics of the display picture of the
screen together with the gray scale and the effects are most excellent
gray, excellent gray, relatively excellent, medium gray, better gray,
general gray and basic gray respectively. The higher the gray scale is,
the better the gray effect will be. The lower the refresh rate is, the
smaller the size of the screen that the unit receiving card is equipment
with will be.
[Refresh rate] LED display screen updates the rate of the picture. The
higher the refresh rate is, the more stable the frequency image will be.
If the ripple and scintillation intend to be avoided when the camera is
used to shoot the picture, the refresh rate shall be established more than
600hz. If the display screen with double color does not lay emphasis on
the effect, 60-75HZ is usually established and the effect of the color
display requirements is established as 180-600hz for the indoor screen
and 300-1200hz for the outdoor screen.
The refresh rate later is the type which undergoes the calculation while
the refresh rate previously is the actual type. The user can modify it
according to the actual needs but the scope shall be smaller than the
refresh rate after being calculated.
[Line][Row] The size of the screen equipped by the monolithic
receiving card is set. The size is adjusted to influence the refresh rate.
◆ Wizard
Click [Wizard] at the lower left side of the dialogue box [Set LED
control equipment
equipment… …]
9
10
◆ Array setting
11
1.1.2 Type of DBT-Q2007 and DBT-Q2009 control system
◆ DBT-Q2007 control system: DBT-Q2007 full color\double color
sending card, DBT-Q2007 receiving card, MINI receiving card,
DBA-7.0 asynchronous control system, brightness temperature and
humidity sensor, power control board and DVI distributor etc.
[Chip that DBT-Q 2007 receiving card supports]
DBT-Q2007
MBI5026、MBI5024、TB62726、TB595、MBI5027 etc.
◆ DBT-Q2009 control system：DBT-Q2009 sending card、DBT-Q2009
receiving card, video processor, DBA-9.0 asynchronous control system,
multi-function control panel etc.
[Chip that DBT-Q2009 receiving card supports]
MBI5026、BI5024、TB62726、TB595、MBI5030、MBI5036、MBI5039、
MBI5042、MBI6030、MBI6020、DM413、LPD6803
Section II Review of the performance of

DBT-Q 2007/
DBT-Q2007/ DBT-Q
2007/DBT-Q 2009 control system
DBT-Q2009
1.2.1 Function description
◆ Supporting 10 digits of colors
The maximum number of the colors that DBT-Q2007\DBT-Q2009
system is 1024*1024*1024=1073741824 kinds of colors.
◆ Self-replacement of the language and LOGO of the company
XMPLAYER is equipped with simplified Chinese, traditional Chinese,
English, Japanese, Korean, Russian, German, French and Spanish etc.
in addition; it supports the self-modification of other languages and the
self-replacement of the LOGO of the company.
12
◆ Supporting multiple scan modes
DBT-Q2007 and DBT-Q2009 systems support: static, 2 scan, 4 scan, 8
scan, 16 scan and other scan modes.
◆ Supporting the driving chips with PWM
The coordination of the professional chip is entailed to make the effect
of the display screen more perfect.
◆ Supporting the point by point revision function of the hardware
DBT-Q2009 system supports point by point revision which supports
single point, 2*2point, 4*4point and 8*8point the four modes. The
largest receiving card with single sheet supports the revision of
128*128 point.
◆ Supporting the function of the error detection
DBT-Q2009 system supports the function of the error detection but the
coordination of the MBI5030\MBI5039\MBI5036 driving chip is
needed to dynamically inspect the flow situation of the display screen.
◆ Gigabit technology
This is definitely the perfect gigabit. The standard of the sending card
with single sheet can own 1280*1024 resolution and the maximum
amount that it can take with is 2048*600 resolution. The single net wire
can utmost be equipped with 2048*300 resolution.
◆ Gigabit network card replacing the sending card and display
card directly
The gigabit network card can be equipped with point screen of the
receiving card instead of the sending card and display card directly.
Disadvantage: the configuration of the computer is required higher (the
usage rate of CPU is extremely high) and the screen with smaller scope
can be equipped with limited functions.
◆ Arbitrary setting of the gray and refresh rate
The clients can adjust between the non-gray and 65, 536 grade (64K)
gray arbitrarily according to the situation of the display screen; the
refresh rate can also be adjusted on a manual basis to make your display
screen reach the best display effect.
◆ Hot standby function of the double net wires
Both A and B port of the receiving card can be used as the input or
output, and they can also be used for two computers to control the same
screen. When one computer encounters some problems, the other one
will replace it automatically for controlling or the double net wires of
one computer can be used for controlling. When one net wire
encounters some problems, the other one will replace it automatically
for controlling to guarantee the normal work of the display screen to the
utmost.
◆ Sound transmission function
13
DBT-Q2009 sending card integrates the sound transmission without the
need of audio line additionally to transmit the sound to the display
screen. Double 24 bit 64 khz high fidelity digital signal→ analog signal
and analog signal → transformation of the digital signal to make the
image effect of your display screen perfect.
◆ Ultra-long transmission distance
The longest distance of the transmission is 160 meters (actual
measurement) and the reliable transmission distance can be as long as
130 meters. When surpassing 130 meters, we suggest using the fiber
transmission. When the transmission distance is between 130 and 1,
000 meters, it is suggested to use the multi-mode fiber transmission;
when the transmission distance is more than 1, 000 meters and less than
10, 000 meters, we suggest to adopt the single-mode fiber for
transmission. (Note: Since our system adopts gigabit transmission,
the fiber transceiver we use shall also be gigabit type).
1.2.2 Recognition of the DBT-Q2007 and DBT-Q2009 hardware
1.2.2.1 DBT-Q2007 full color sending card
◆ DBT-Q2007 main control card (sending card is built in) is illustrated
in the following figure:
The explanation illustrated in the figure is as follows:

[B1] Standard PCI interface is used for inserting into the PCI slot of the
computer; there are three interface kinds between our main control card
and the computer and they are PCI interface, USB interface and RS232
interface respectively. Since the RS232 interface among them is seldom
equipped in the current compute, we have shut down our production
and the user can give an order when necessary. The internal type mostly
adopts PCI communication nowadays while the external type uses USB
communications.
[J201] Standard DVI interface is connected by the matched DVI wire
14
and DVI interface of the display card of the computer. There are four
lamps among which two are in green color and yellow color
respectively on the side of the two RJ45 outputs. Only a yellow lamp in
the middle will flash after connecting with the DVI output of the
display card. The two green lamps will be bright, the yellow lamp in the
middle will flash slowly while the yellow lamp along the side will flash
quickly only when the second output of the display card of the
computer is opened. More details about how to open the second output
of the display card refer to the manual of the display card purchased or
the settings of the display card in the appendix.
[JP501] Is the data transmission port of tow RJ45. The one next to the
USB interface is the first output following with the second one which is
connected by the standard five-category net wire and the input of the
HUB scan board. One transmission port is able to transmit 640 rows of
data to the utmost (different screens own different row parameters on
how many rows are equipped).
The baffle that RJ45 and DVI correspond to is as the following figure:
Special explanation of the pilot lamp at the net mouth of the sending
card:
[No. 1 green lamp] Not bright, no indication function
[No.2 yellow lamp] It means the procedure within FPGA is working
normally when flashing.
[No.3 green lamp] It means the main control board is under normal
work in case of being always bright and there is signal output in the
second RJ45 when it is always bright. No output will be demonstrated
in being not bright.
[No. 4 yellow lamp] Flashing means that the work from DVI output to
the main control card is normal. It will not be bright when the DVI
output of the display card is not opened or under abnormal work.
[USB interface] It connects with the USB interface of the computer by
the matched USB wire and the D601 green pilot lamp on the main
control board will be bright after being connected, which means USB
interface is normal; it will not be bright without connection. When the
main control board inserts into the computer and since it has already
undergone PCI communication, the USB wire beyond the computer can
select not to be inserted, which will not influence the application of the
15
control system.
Note:
When USB interface is adopted for connection, please connect with
the USB output on the main board directly and then make sure
your computer does not exist virus, since some kinds of virus may
probably close the USB interface.
[DVI interface] It connects with DVI output of the display card. When
the second output (DVI) port of the display card is opened, No. 1 and
No. 3 green lamps and No. 4 green lamp will be bright at the same time
and No. 4 yellow lamp will flash continuously.
[JP602] Standard USB-B type socket is used for the communication
with computer. When the main control card has been inserted into the
PCI slot of the computer, USB communication wire can select not to be
inserted. Since the main control has carried out communication with
computer by means of PCI. If the USB wire is inserted at the same time,
it will not influence the communication with computer.
[D601] The green pilot lamp will be bright when the communication
wire between the USB wire and the computer has been inserted. The
lamp will not be bright on condition that the communication wire has
not inserted or USB interface of the computer is unable to carry out
communication.
[D102] The red pilot lamp will be bright when main control card is
inserted into the computer or powers up by means of J102, which
means normal electrifying. If the lamp is not bright after the main
control card is inserted into the computer or carries out direct
electrifying, please never carry out other work before making it clear in
order to avoid the damage of the main control card.
[J102] This is the input of the power, among which No.1 and No. 3
connect with +5V while No. 2 and No. 4 connect with GND ground.
When the main control card is inserted into the PCI slot of the computer,
it is not necessary to carry out connection. The main control card has
been passed through PCI to get electricity.
Note:
When the main control card connects with the computer for the
first time, please press [send all the parameters] within [LED
control setting] panel after finishing installing the software, which
is equivalent to the initialization of the main control.
◆ The outdoor type main control of DBT-Q2007 sending card is as the

following figure
16
Special explanation of the pilot lamp of the net mouth of the external
sending card:
[No.1 green lamp] Not bright, no indication function
[No.2 yellow lamp] It means the procedure within FPGA is working
normally when flashing.
[No. 3 green lamp] It means the main control board is under normal
work in case of being always bright and there is signal output in the
second RJ45 when it is always bright. No output will be demonstrated
in being not bright.
[No.4 yellow lamp] Flashing means that the work from DVI output to
the main control card is normal. It will not be bright when the DVI
output of the display card is not opened or under abnormal work.
[USB interface] It connects with the USB interface of the computer by
the matched USB wire and the D601 green pilot lamp on the main
control board will be bright after being connected, which means USB
interface is normal; D601 will not be bright without connection. The
USB wire of the external main control must connect with the computer,
otherwise all the changed parameters in the display screen will fail to be
used.
[DVI interface] It connects with DVI output of the display card. When
the second output (DVI) port of the display card is opened, No. 1 and
No. 3 green lamps will be bright at the same time while No.2 and No. 4
yellow lamps will flash continuously.
[POWER] This is the standard 110V-220V power socket the switch of
which is on the other side of the main control box with red pilot lamp.
◆ DBT-Q2007 double color sending card:
The dimension of DBT-Q2007 double color sending card is the same
with that of DBT-Q2007 full color sending card. What the difference
lies between them is that the data of DBT-Q2007 double color sending
card can only pass through USB interface and support single\double
color screen.
1.2.2.2 DBT-Q2007\DBT-Q2009 receiving board (HUB board)
◆ DBT-Q2007 receiving board (HUB board):
17
[J1] This is the power connection base. 5V connects with the positive
5V power while GND connects with the ground.
[J2] This is the power socket, among which 1 connects with the
positive 5V power while 2 and 3 connect with the ground.
[J4] This is the procedure writing port. When the procedure finishes
writing and HUB board is under normal work, 2 and 4 foot are required
to carry out short circuit, which is illustrated as the black dot in the
figure above.
[J6] This is the signal port of two RJ45 (input and output of the
self-defining of the two RJ45) connects with the output of the main
control card by means of the standard five-category net wire (508B)
and more details about the pressure method of the net wire refer to the
explanation of the appendix.
[J7, J8 and J9] These are the data outputs and among which J7 and J8
are the socket of the flat line of 50-core and the 50-core flat line is used
to connect with the interface board of the different screens on the
market. Each 50 flat line outputs 8 data lines. J9 is the special kind of
our company and it is used to additionally increase 8 data lines (that
means there are 24 output signals on the whole board which can
connect with different screens by means of the interface board of our
company. J8 is the first output of scan and the corresponding between
grounds shall be noticed. Additionally, one end with double-arrow
mark is the first stitch;
[JP1] Is the polarity switch of the enabling (OE) and it shall be ON
status under the normal working conditions.
[SW1] Is the measurement button of the display screen and under the
condition without connecting with the main control, the display screen
will appear all red, all green, all blue and gray these kinds of
measurements only by keeping pressing the button for 3 seconds. The
image will switch between the red, green and blue vertical line and the
18
inclined line by pressing for twice continuously under the status that the
measured image appears. The measurement mode will be end only
inserting the net wire on the RJ45 port.
1.2.2.3 DBT-Q2009 receiving card (HUB board):
◆ Structure and working condition of the
hardware
Rated voltage：5V+0.3V；
Rated current：3A；
[Fin]
Gigabit transmission chip RTL8212
(one chip for one card). Fin is needed
to be pasted.
[Dial switch] There are 4 dial switches (DIP) dialing to [ON] direction
in course of the factory default settings.
The first dial switch (DIP1) controls

upper 50-core OE signal polarity;
The second dial switch (DIP2)
controls lower 50-core OE signal
polarity
(When getting electricity, that the dial
switch controls OE signal polarity is
valid and OE polarity fails to be
adjusted by dialing the dial switch
after getting electricity.
The purpose of such design means to
avoid the phenomenon of the LED
19
display screen reversing these OE
polarities burns the line output
transistor when getting electricity);
The third dial switch (DIP3) is used in
the function of the receiving card
measuring LED module groups and
more details are illustrated in the
following page;
The forth dial switch (DIP4) has not
been used temporarily;
[Jumper cap] 2 jumper caps are needed in the place of 601 (only one is
needed in the earlier version):
[Transmission net wire] National standard net wire, CAT5E or more

excellent materials;
Among the two net mouths, the one that is closer to the side of the
power is used as the data input while other one acts as the cascade
output;
[Digital tube] Is used to display temperature and status information;
When there is effective image data in the net wire, the pilot lamp of the
receiving card will flash and the digital tube displays the temperature
normally; otherwise the pilot lamp will be always bright and the digital
tube flashes, moreover, it will be closed and output to the signal of the
display screen which will become black screen;
1.2.3 Recognition of the DBT-Q2007 and DBT-Q2009 software

◆ Software for parameter setting
20
◆ Parameter interpretation
21
[Data clock frequency] Corresponds with LED driving chip such as
MBI5026/MBI5030 data clock frequency DCLK and it shall be noticed
that within the frame (62 of the previous figure) is the frequency
division number with respect to the internal clock 125MHz. The
frequency display of DCLK is beside (such as 10.41MHz=125MHz/12
frequency division in the figure above);
[Data clock duty cycle] Is the one of the [data clock frequency]
DCLK and open it by clicking:
The adjustment of the [data clock duty cycle] here can not only
applied to the data clock duty cycle of the clock. The location of the
high level of the clock also needs changing, which is practical to some
LED screen;
[Polarity reversed-phase of the data clock frequency] The high level
of the clock will become the low level and vice verse after selecting the
option;
[Latch signal space] One latch signal pulse shall be realized to make
the data store in the data buffer of the LED driving chip for the purpose
of continuing the next data transmission after LED driving chip finishes
the data transmission for once. The time interval between the twice data
transmission, which means the time giving for the latch signal pulse, is
the [latch signal space]
space];
[Pulse width] The same with [data clock duty cycle] of the [data
frequency], the latch signal pulse width is also able to adjust the
clock frequency]
data clock duty cycle and the location of the high level;
[De-shadow time] As for the scan screen, since the LED driving chip is
used among several rows and the through display completion of the
data in the previous row has to be waited before the data in the next row
is input, the waiting time is [de-shadow time]
time].
[Gray scale] Means the gray scale that can be indicated and what it
22
represents is the bit number of each color of the characterization.
Taking the figure above as an example, the gray scale is 4,096; it means
that each color utilizes 12 bit characterization.
(2^12=4096)；
[Gray effect] Is the unit time number of the maximum bit of the
characterization color displaying in the LED.
“Most excellent gray”: The maximum characterization of the color
displays 64 unit time
“Excellent gray”: The maximum characterization of the color displays
32 unit time
“Relatively excellent”: The maximum characterization of the color
displays 16 unit time
“Medium gray”: The maximum characterization of the color displays 8
unit time
“Better gray”: The maximum characterization of the color displays 4
unit time
“General gray”: The maximum characterization of the color displays 2
unit time
“Basic gray”: The maximum characterization of the color displays 1
unit time
“Refresh rate” means the repetitive display frequency of the same
image in LED display screen and under “frame synchronized mode",
the value is the multiple of the frequency 60Hz of the image of the
display card while under the non-frame synchronized mode, the value
will be the average display frequency of the image instead of the
multiple of 60Hz.
[Row/line] This is the regulated pixel area to display the image of the
single receiving card;
[Brightness loss] The brightness loss with respect to the LED tube
when it is always bright is the loss of the time domain, which means
that LED tube does not own the lightening time capacity; brightness
loss results from the occurrence of gray;
[10 bit data source] Means what the sending card transmits to the
receiving card is the 10b high definition video source and the common
DVI data is 8b video source;
[HUB data conduplication] Means that the 50-core data in the upper
and lower of the receiving card controls the right and left half part of
the LED display screen respectively instead of controlling the upper
and lower half part of the LED display screen generally; meanwhile
guaranteeing the refresh rate, such connection sacrifices half vertical
loading areas with twice horizontal areas;
[dat
[dataa on mirror] Represents mirror image of the image on the right
half part of the forward-looking of the LED display screen. At this time,
23
the right half part of the forward-looking of the LED display screen is
driven in from the left side while the left half part is driven in right side;
[line before gray] Under general circumstances, scan screen starts to
scan gray following with rows and the reason why it is carried out like
this is to reduce the times of row changing of the data; [line before gray]
displays that the visual effect is evener than the former one, the image
is stable while the shortcomings are that it influencing closing the row
and the shadows among the rows are difficult to eliminate;
[Power on gradually-brighten] The function produces the effect from
being dark to bright when the LED display screen powers up and the
reason why it does like this aims to avoid producing excessive power
load due to illumination meanwhile all the LED tube are powered up.
[Left driving of the data] Under general circumstances, the data
displayed on the LED display screen is right driven in form of the
forward-looking and selecting the option means the data of the LED
display screen is left driven.
[Receiving setting]
24
[Scan mode] The line scanning specification of the scan screen
supports non-standard scan (select [Custom]
[Custom]).
[Rows drived per data port] Means the rows of LED display screen
driven by a group of GRB and the maximum row is 32;
[Data polarity] Points to the polarity of the red, green and blue data.
Some LED display screen adds inverter in the input end of RGB data;
[Color order] Means the corresponding relationship of the RGB
arrangement on LED display screen and the RGB on the 50-core of the
receiving card;
[Scan decoding type] “138/139”: Decoder decode
“Full-decode”: Without decoder, supporting 4
scan full-decode utmost
“CD4094/595”: Shifter;
[OE mode] This is the control mode of OE polarity, “using hardware
control" means adopting the dial switch DIP1/DIP2 on the receiving
card for selection and “positive mode/negative mode” points to the OE
polarity of the software control;
[LED driver] The driving chip which is adopted by the LED display
screen is selected;
[Minimum OE pulse width] The minimum pulse width which is able
to response when corresponding to the driving chip can be filled in;
[24 groups of data modes] the receiving card is able to output 24
25
groups of RGC data utmost to make the vertical loading area 50% more
than that of the competitors (pinboard of the 24 groups of RGB data
signal is entailed);
[90°°image rotation] It will facilitate LED screen flip when the picture
[90
rotates 90 degrees;
[Gray order] The display order of the bit number of the
characterization RGB data on the LED display screen means that either
displaying the low bit gray or high bit gray can be accessible for the
precision adjustment of the display effect of the screen;
[Row order] It is allowed that LED display screen is arranged
arbitrarily between 16 rows, which can facilitate the cloth plate of the
LED display screen. It also applies to some special application, such as
the data transposition between RGB data groups;
[64 row mode] "Row order” has 64 order items after being selected and
each of them is the extension of the previous item;
[Data path]
26
Data path is the order of dot drawing when “wizard is carried out and it
reflects the routing patterns of the LED module group (maximum 256
pixel arbitrary routing). The parameter will be produced automatically
after the wizard is finished and it is not necessary for modification
under general conditions;
27
【GAMMA
GAMMA
GAMMA】
The value of
GAMMA meter is adjusted by regulating coefficient (1.0-4.0) of
GAMMA and the coefficient that DSTAR recommends is 2.8.
GAMMA meter can be customized after selecting [customization]
[customization],
which aims to face some LED display screens with irregular
illuminations.
28
[Light tube]
The parameter of the light tube is the serial rules of the LED display
screen which establishes red, green and blue serial transmission and the
vacuum point and repetitive point are allowed, which means the pin on
the corresponding driving chip can choose not to connect with LED
luminescent tube or the LED luminescent tube on multiple pins of the
driving chip can display the same point etc.
[Group end] represents the cycle end of a pixel point;
29
[Brightness adjustment]
No selecting [MBI5030/MBI5039] means what is adjusted at present is

the brightness of PWM which aims to control the brightness by means
of controlling the multiplier to adjust RGB data value;
After selecting [MBI5030/MBI5039] means the current adjustment is
the brightness of the current gain (CGA) which sends the current gain
value to the driving chip to control the output current of the driving
chip for the purpose of controlling the brightness of the LED
luminescent tube, therefore, only the driving chip which supports
current gain is able to adjust the brightness of the current gain;
The advantage of adjusting the brightness of LED luminescent tube by
means of adjusting the current gain is that it will not damage the
perfection of the image data;
Selecting [Collecting data] means the brightness results from the
brightness sensor at the serial port of the connection computer, in this
way, that the brightness of LED display screen can be adjusted
according to the brightness of the environment is realized and the
related configuration can be checked by opening [Set] button.
Another automatic brightness adjustment mode with sensor carries out
series connection with a DSTAR multifunctional card in the queue of
the receiving card (the function such as audio transmission, temperature
and humidity sensor and power control are possessed), the function
card collects brightness automatically and then sends to the receiving
card to realize the automatic adjustment of the brightness.
[Queue setting of the receiving card]
Queue of the receiving card is the arrangement order of the receiving
card of the mutual cascade controlling LED display screen and it is
used to set the image area controlled by different receiving cards.
30
Click [Insert] to establish a queue of the receiving card:
The net wire cascade order of the value characterization on the

receiving card in the figure
Open [Brightness adjust] after selecting s`ome receiving card and the
correction parameter can be independently sent to the receiving card:
The monolithic receiving card supports the brightness correction or
chroma correction with 128*128 pixel area to the utmost;
The current correction mode can be selected: brightness correction and
chroma correction;
The correction of some receiving card can be opened/ closed
independently;
The correction of the red, green and blue color can be established
individually and the four-color correction can be set independently
under the virtual pixel;
The correction parameter can be derived from save or introduced to the
saved correction parameter or the correction information of the third
pane;
Point by point parameter correction is an 8-bit data with the 0-255
number range;
31
1.2.4 Main performance index of the DBT-Q2009 receiving card
◆ Supported LED driving chip:
MBI5026/TB62726 and its compatible chip; MBI5030/MBI5042 and
other driving chip of the automatic PWM; MBI5036/MBI5039 and
other driving chip with current gain and error detection;
MBI6020/DM413/LPD6803 and other driving chip of the electric light
source;
◆ Maximum data group number: 24
� Maximum driving row number of a group of data: 32 rows
� Maximum line scanning: 32 scanning
� Maximum loading pixel area of the single receiving card:
� Full color: 2, 048 line *256 row (16 groups of data) or 1, 024 line
*384 row (24 groups of data);
Double color: 2, 048 line *512 row;
Minimum OE pulse width: 8ns;
� Maximum frequency of DCLK: 125MHz / 4 = 31.25MHz;
� Maximum pixel area of the drawing dot: 256;
� Maximum gray grade: 65, 536 grade (16 bit);
� Adjustment grade of the PWM brightness: 256;
� Adjustment grade of the current gain: 256;
� Light tube control (RGB data serial): supporting the vacuum point
and repetitive point within 64 point pixel;
� Revision of the point by point brightness/ maximum pixel area of
the chroma correction: 128*128;
� Maximum pixel area of the error detection: 512 point* line
32
scanning* 16
� Returning path error detection of 16 groups of data:
The loading area will not be influenced and 20pin extended port is
utilized to pass back the error detection data;
The upper and lower 50-core

contain 16 groups of RGB data
which are used for controlling
the display of the LED screen.
The extended port of 20 core
on the right contain pass-back
data which come from a
pass-back data group while the
selection board is used to
select one group in the 16
groups of the pass-back data.
Error detection is carried out
and passed back group by
group.
1.2.5 Error detection function
◆ The driving chip that supports error detection function

[MBI5036] supporting the error detection in information
[MBI5039] supporting 3 kinds of error detections
33
[MBI5030] supporting the inspection of the open circuit and short
circuit
Note:
The error detection of the MBI5030 differs from that of the
MBI5036/5039
� Connection graphic of the error detection and points for attention

Three kinds of connection methods of the error detection of DSTAR
DBT-Q2009:
[8 port detection]
[12 port detection]
[16 port detection] [Selection board of the pass-back data] is

entailed and DBT-Q2009 extended port shall be connected. (20
core)[[selection board of the pass-back data] function is to select one
group among 16 groups of R0GBR1 data which are passed back by the
LED screen by means of 74HC152 (select 1 from 16 groups and the
selection signal is offered by DBT-Q2009 20 core extended port) to
finally connect to the DBT-Q2009 20 core extended port.
34
The upper data line is transferred among DBT-Q2009 50-core interface
and RGB data line is not allowed to pass through 74HC245, since the
DIR direction signal determines the data is transferred from
DBT-Q2009 50-core to the adapter panel when under normal display
while it is required that the signal direction is transferred from the
adapter panel to DBT-Q2009 50-core when under error detection.
74HC245 DIR direction signal between DBT-Q2009 50core and FPGA
is controlled by procedure.
35
◆ Interface definition when the extended port acts as 16 port for
detection
◆ Detection pixel point (The pixel area that one block of the
DBT-Q2009HUB can be detected)
[Static screen] a group of data (One data port) can detect pixel point
512*4 (The static screen carries out detection with four times
automatically), that means if one group of data of the screen is
equipped with 8 row high, 512*4/8 ＝ 256 row can be detected. The
overall detection point number of 8 port detection, 12 port detection and
16 port detection are:
“Overall detection pixel point of 8 port” 512*4*8 = 16384 point
[Scan screen] one group of data is able to detect pixel point 512* scan
mode (2 scan for 2, 4 scan for 4 and 8 scan for 8…), that means 8
screen scan (1/8 scan) one group of data can detect the point with
512*8= 4096 point number. If 8 screen scan one group of data is
equipped with 16 row high, 512*16(post high)/8(scan) =1024 row can
be detected. The overall detection point number of 8 port detection, 12
port detection and 16 port detection are:
4096*8=32768 point
4096*12=49152 point
4096*16=65536 point
[Detection time]
All the DBT-Q2009 which cascaded together can finish detection
within 4 seconds but certain time is needed to pass back the data to the
computer. Generally speaking, 2-10s is needed to pass back a block of
error detection data of the DBT-Q2009 (it is determined according to
the data amount), that means 200-1, 000s is entailed for the error
detection time of the LED display screen composed of 100 blocks of
36
DBT-Q2009 for once (4-17 minutes)
[Influence of the error detection to the normal display of the big
screen]
As for the detection of In-Message, MBI5036/5039 actually can never
influence the normal display totally, however, it fails to detect all the
errors for once, since In-Message detection requires that display data
is ’1’ and OE is in low level, which means that only the luminescent
tubes can be detected. When it is in normal display, it is possible that
some luminescent tubes are not bright. In order to detect all the errors in
one time, DSTAR DBT-Q2009 adopts the method of forcing the data to
be placed ’1’ and OE is in low level, however, if doing so, the normal
display (LED display screen will turn white instantly) will be affected
instantly in course of detection.
As for the forced error detection, since MBI5036/5039 adopts the
method of opening the LED instantly for detection, the influence of the
DBT-Q2009 receiving card to the LED big screen is very small in
course of the detection.
[Points for attention of the shield design]
○ The driving chip of many scan screen OE are grounded, which
directly results in the failure to carry out “forced open-circuit detection”
and “forced short circuit detection”. Therefore, the method of making
the driving chip grounded is not recommended.
○ The advantage of the LED driver which supports the built-in PWM of
the built-in PWM driving chip:
○ The update time of the image data is reduced to enhance the update
rate of the image data;
○ The visual refresh rate of the LED display screen is enhanced (special
PWM accounting algorithm);
○ Extremely excellent and low-gray representation (without the
response problem of OE pulse width).
Note:
Taking MBI5030 as an example
37
[Parameter interpretation]
The gray scale of PWM: The digit capacity of the bit of the
characterization RGB with deep color decides the range of the PWM
counter;
Count mode of the PWM: the S-PWM technology specially possessed
by MBI can enhance the visual refresh rate dramatically;
Synchronous mode of the PWM: the scan screen forces “manual
synchronization” and the static screen suggest “automatic
synchronization";
GCLK frequency: The clock frequency is the same with that of DCLK
when PWM carries out counting and the value within the frame is
frequency division number with respect to 125MHz;
[Points for attention for the parameter configuration]
○ As for the scan screen, DCLK and GCLK need certain linkage due to
the interior requirements of the driving chip with PWM, thus, when the
adjustment of one frequency will influence that of another and the
algorithm is automatically calculated by the software; The static screen
does not have such problems;
○ As for the scan screen, it is generally suggested that [PWM count
mode] is set as [00] to enhance the refresh rate dramatically. “PWM
gray scale” is suggested to establish as “12bits” (4096 grade scale),
which is also beneficial to achieving relatively ideal refresh rate. This
of course can be determined according to the actual situation; the static
screen is adjusted according to the requirements;
○ As for the scan screen, the refresh rate displayed on the software
(illustrated in 600Hz in figure above) is the data update rate and the
multiple of the visual refresh rate produced by S-PWM is beyond
calculation. Since to the scan screen, data update rate makes greater
38
contribution to the visual refresh rate; as for the static screen, the
refresh rate displayed on the software has calculated the multiple of the
S-PWM refresh rate, therefore, the refresh rate of the static screen
usually can reach thousands of values;
○ [Latch signal interval time] and [de-shadow time] can establish
smaller value, illustrated in 2;
○ Order of the parameter configuration: select the driving chip-> set the
row, line and scan mode etc. of the loading of the receiving card-> set
“PWM gray scale” (“12 bits is suggested to be used) and “PWM count
mode” ("00" is suggested to use) ->set proper GCLK frequency->carry
out fine adjustment to DCLK to match with GCLK;
○ The scan screen which builds in the PWM driving chip does not
support “scan row following with gray”;
○ 24 groups of data output is not supported when the PWM driving
chip is built in and only 16 groups of data output is supported.
○ Application of the MBI5030/MBI5042 on RGB serial LED display
screen (color curtain and light tube):
Since the driving chip which builds in PWM reduces the update time of
the image data significantly, data transmission can be carried out even
though DCLK operates under a very low frequency while both the
visual refresh rate and image quality represent well, therefore, the
application of it in RGB serial LED display screen becomes the ideal
choice and the effect is much better than the common driving chip with
the constant current source (such as MBI5026);
DSTAR DBT-Q2009 (DBT-Q2009) LED control system supports
MBI5030/5042 and the application of other driving chip with interior
PWM on RGB serial LED display screen as well as the vacuum point
and focal point;
○ Other LED driving chip which builds in PWM (mainly with point
light source):
LPD6803
Only the LED driving chip of the point light source with 5-bit deep
color is supported and used in the low-end application with relatively
low color requirements. Moreover, crystal oscillator is built in;
DM413
The crystal replacement supports the LED driving chip with point light
source with 8-bit deep color and the current gain is adjustable;
MBI6020/MBI6030
MBI supports the LED driving chip with point light source with 16-bit
or 10-bit deep color and the current gain is adjustable. The crystal
oscillator is built in and GCLK can also be offered on an external basis;
The driving chip which builds in PWM will also be supported in the
later stage:
39
MBI5050
MBI builds in 8 rows of data buffer and supports the application of the
scan screen with 2-8 scan; TC62D722: Toshiba;
STP1612PW05
ST STMicroelectronics Company;
1.2.6 Additional function
Function of LED screen measurement by relying on receiving card
under the condition without the sending card;
◆ Function of give measurement graphics
[Key-press principle]
○ Start-up:
Light the screen to be tested before starting up (the correct parameter is
set) and then unplug the net wire; keep pressing the button on HUB for
3 seconds after unplugging the net wire or powering up to enter the test
states (note: when powering up, it is suggested that the dial switch be
dialed to the number “2” to ensure that the test states can be entered by
keeping pressing the button for 3 seconds, otherwise 9 seconds or a
more longer time is entailed, the reason of which is probably that the
parameter of the “power on gradually-brighten” is established. The
normal display status can be achieved by inserting the effective data net
wire again (the dial switch 2 shall be dialed to ‘ON’ direction at this
moment);
○ The defaulted test graphic is in red color after entering the test states.
○ Key-press shall be finished within 1 second for each time and the
interval time for key-press shall be at least 2 seconds;
○ Once or twice is feasible for key-press in each time and the
representative meaning is that: when the dial switch 2 is dialed to ON
direction:
Pressing the key for once: cycle stepping is carried out in 5
measurement examples;
Pressing the key for twice: pause/restart (it will remain the current
measurement example and the picture is made to move by pressing for
twice again;
◆ Digital tube display
40
Section III Temperature and humidity sensor
1.3.1 The connection schematic diagram is as follows:
1.3.2 The application of the sensor in DBT-Q2007 synchronous

system
◆ Switch setting
They are non-humidity sensor head 11111001; humidity sensor head:

41
01111001.
The seventh and eighth switches are the selection of the response speed:
“00” is 0.5S, “01” is 1S, “10” is 10S and “11” is 60S.
◆ Serial connection method: One head is DBT-Q9 male head and the
other is DBT-Q9 female head, 2-2, 3-3, 5-5.
◆ Software setting: Tick the data collecting in “XMPLAYER”
parameter setting and come into [set] to tick the brightness automatic
adjustment after selecting the correct connection serial, then click send
at the right side of the set. The function can be realized after finishing
sending and exiting the software to the playing window.
1.3.3 Application of the brightness sensor in DBT-QA9.0

asynchronous system
◆ Switch setting
They are non-humidity sensor head 11110101; humidity sensor head:

01110101.
The seventh and eighth switches are the selection of the response speed:
“00” is 0.5S, “01” is 1S, “10” is 10S and “11” is 60S.
◆ Serial connection method
One head is DBT-Q9 male head and the other is the 10PIN needle of
double-row. DBT-Q9 utilizes 2, 3 and 5 foot and the 10PIN needle with
double-row adopts 5, 6 and 7 foot (the arrow place of the needle with
double-row is the tenth foot), 7-3, 6-2, 5-5.
� Software setting
Tick the data collecting in “XMPLAYER” parameter setting and tick
the brightness automatic adjustment and then confirm after coming into
[set] to select the correct serial, then click send at the right side of the
set. The function can be realized after finishing sending and exiting the
software to the playing window. The program sheet of the sensor
display is added when manufacturing the program and the brightness
automatic adjustment [Yes] is selected at the right side of the materials.
Decisions shall also be made as whether the temperature and humidity
are displayed and then the program is sent to ARM9 to realize the
function.
42
Note:
Other program window can not overlap the brightness display
window and the selection between the first layer and second layer
shall be separated.
1.3.4 The application of the brightness sensor in DBA-7.0

asynchronous system
◆ Switch setting
◆ 1-8 are:
[Non-humidity sensor head] 11110001
[Humidity sensor head] 01110001
Note:
The seventh and eighth switches are the selection of the response
speed: “00” is 0.5S, “01
00” ” is 1S, “10
01” ” is 10S and “11
10” ” is 60S.
11”
◆ Serial connection method: One head is DBT-Q9 male head and the
other is DBT-Q9 female head, 2-2, 3-3, 5-5.
◆ Software setting: Only the brightness automatic induction is entailed
and the software setting is not necessary. If the temperature and
humidity need displaying, it needs: select the temperature and humidity
in the overall customized information of the ARM6.0 software and the
function needed can be realized by sending again.
43
Section IV Power control board
1.4.1 Graphic of the real material is as follows:
The connection graphic with DBT-Q2007 synchronous receiving

card is as follows:
44
Schematic diagram:
1.4.2 2009 multifunctional board

◆ Function introduction:
[Power automatic control]
[Control of the temperature, humidity and brightness]
Note:
The functional board R24 and R25 weld 1k resistance, single chip
microcomputer PIN25 and PIN 26 short circuit respectively.
◆ Hardware part
[Digital tube] Temperature display of the card and display of the

collecting temperature
45
[Audio output] Outputs sound and connects with the amplifier or
sound box.
[Interface of the temperature, humidity and brightness sensor]

Connect with the probe of the sensor
[Power control relay] 6 circuit controls the switch of the contactor

with small power independently and each circuit connects with the
power contactor with big power. The external power of the 6 circuit can
be controlled independently.
○ The connection diagram of the hardware is as the following figure
46
Note:
220V is the coil voltage of the AC contactor (AC contactor has
explained for this)
[Probe of the temperature, humidity and brightness sensor]
1,
The figure above is the interface of the functional card while the figure
below is the sensor of the brightness and temperature. (Powering up is
effective after connecting with the sensor).
○ Pressing line method of the probe of the sensor
I. Only RJ45 pressing line method of the temperature and brightness is
possessed.
MATE functional board:
(1) White orange (2) orange (3) white blue (4) blue (5) white green (6)
green (7) white brown (8) brown
Sensor head [SENSERout1.1]:
(1) White orange (2) orange (3) white green (4) blue (5) white blue (6)
Note:
Not supporting SHT1X humidity
II. RJ45 pressing line method of the temperature, humidity and

brightness
MATE functional board:
(1) White green (2) orange (3) white blue (4) blue (5) white orange
(6) green (7) white brown (8) brown
47
Sensor head [SENSERout1.1]:
(1) White orange (2) orange (3) white green (4) blue (5) white blue (6)
Note:
Not supporting DSI8B20
◆ Software part
[Switch control]
Select [Power management] and click [Switch control]
Click the corresponding power switch button according to the

application need and click [Ok]
[Schedule]
Click [T imely order]
There controller owns 6 groups of switches that can be used. Click

[Connect] and [Disconnect] icons to realize [Enter] of the switch
power. Meter screen between the appointed orders can be established
for automatic power switch according to the schedule automatically.
48
Chapter II Asynchronous control
System
Section I DBA-9.0 asynchronous control

system
2.1.1 Hardware recognition
DBA-9.0 (With net mouth output)

◆ Positive schematic diagram
[SW1] This is reset button.

[CON8] This is power connection base, 5V connects with positive 5V
power and GND conncts with the groud.
[CON5] this is the power socket, among which 1 connects with positive
5V power and. 2 、 3 connects with the ground and 4 foot is no
connection.
[LED5] This is the power pilot lamp and it will be in red color after
electrifying.
[LED1 and LED8] This is the signal lamp and it means the main
control board is under normal work when the two lamps are bright.
49
[CON9] Is the standard RJ45 signal port and connects with the network
port by means of the five-category net wire. As for the pressure method
of the net wires which connects with the computer and information
point, please refer to the appendix.
[J7, J8 and J9] These are the data outputs and among which J7 and J8
are the socket of the flat line of 50-core and the 50-core flat line is used
to connect with the interface board of the different screens on the
market. Each 50 flat line outputs 8 data lines. J9 is the special kind of
our company and it is used to additionally increase 8 data lines (that
means there are 24 output signals on the whole board which can
connect with different screens by means of the interface board of our
company. J8 is the first output of scan and the corresponding between
grounds shall be noticed. Additionally, one end with double-arrow
mark is the first stitch;
[OE] Is the polarity switch of the enabling (OE) and it shall be set on
the on or off status according to the display screen.
[CON6] Serial is used for connecting with other equipment such as the
brightness exteroceptor or temperature and humidity exceroceptor of
our company.
[CON14] This is the socket of the CF card and the mainstream CF card
on the current market.
[CON7 and CON7A] This is the USB interface and the mainstream U
disk on the current market.
Note:
U disk with different specifications and brands is not supported
and we suggest adopting the “KINGSTON
KINGSTON” ” brand.
[CON3] Standard audio output

◆ Back schematic diagram
50
[CON2] This is the standard socket of the SD card which inserts the
mainstream SD card on the market.
[CON1] Inserts the kernel board equipped by our company.
Note:
Since the density of the socket is relatively high, please never insert
or unplug the kernel board casually.
2.1.2 Technical parameters

DBA-9.0 Embedded system parameter
External dimension: 176mm (L) * 109mm (W)
Weight of card: 0.25KG
Working voltage: 4.75V~5.2V
Working current: 1500mA
Working temperature: -10℃~50 ℃
Limit working temperature: -20℃~70 ℃
Working humidity: 5%~95%
Function Double color Full color

Red/green/blue and 4 level *65536 level 4 level *65536 level
gray scale （Parameters can be （Parameters can be
set） set）
The highest clock 25MHZ 25MHZ
output
Storage amount Max 4G Max 4G
Memory interface Support SD card/U Support SD card/U
disk/CF card disk/CF card
51
Function Double color Full color
Transmission Standard network Standard network

interface RJ45 RJ45
RS232/485（Special） RS232/485（Special）
Mode of scan Static, 1/2 scan, 1/4 Static, 1/2/scan, 1/4
scan, scan,
1/8 scan, 1/16 scan 1/8 scan, 1/16 scan
Intelligent guide Support within Support within
16*16 point cabling 16*16 point cabling
mode mode
Control range 640*480（need to 640*480（need to
receiving card receiving card uplink）
uplink）
Output interface Supported standard Supported standard
HUB（16 group HUB（16 group RGB）
RGB） Support special 24
Support special 24 group RGB
group RGB
Support video MPG / MPEG / AVI / MPG / MPEG / AVI /
ASF… ASF…
Brightness sensor Support Support
Multiwindow Support Support
Temperature and Support Support
humidity sensor
Sound output Support Support
2.1.3 Introduction of the application method

◆ Setting of the computer IP: Right click the network neighborhood
and the local connection will appear by clicking property, as the
following figure:
52
Select [Local connection] and click the right key to select [Property]
roperty],
then the following will appear:
(TCP/IP)]], click [Property]

After selecting [Internet protocol (TCP/IP) roperty],, the
fixed IP address is set as the following figure:
53
Note:
I. IP address must not be in conflict with that of ARM 9 due to the
adoption of the same address.
II.. IP address of the computer must be set within the same [section]
II
with ARM9 which is defaulted as “1” section.
◆ DBA-9.0 parameter setting

Click [LED control configure] in the [Control] menu bar, as
illustrated in the following figure:
The dialogue box of [LED control setting] will appear, illustrated as

the following figure:
54
Click [Wizard] button on the lower right side and the following figure
will appear:
Click [Ok]k], DBA-9.0 will restart automatically (Reset) and the

[Wizard] will be operated again after the restart of the DBA-9.0 is
finished until the following figure appears:
The following figure will appear by click [Ok]

k]:
Set according to the minimum module group of your screen and with
rows which are brought by one group of data. Suppose the minimum
55
module group is 16*16 and there are two groups of RBG signals being
controlled, it will be set as 16*8. If there are four groups of RGB
signals being controlled, it will be set as 16*4, click enter key when
finishing setting, as the following figure:
Fill in the dialogue box above according to the rows that are or are not
lighted and click [Ok] after finishing, and then the following figure will
appear:
There shall be one lamp being bright or flashing on the LED screen at
this time and find the corresponding position in the grid figure above
according to the position of the lamp on the screen. There will be
another lamp being bright on the screen to guide you to click it after
clicking and keep clicking until there is not grid to be clicked. Press
[Ok] and the following will appear:
56
Click the corresponding unit row one by one by means of the mouse
according to the order of the illumination line on the display screen.
Click [Ok] after finishing and the following figure will appear:
Click the corresponding unit row one by one by means of the mouse
according to the order of the illumination line on the display screen.
Click [Ok] after finishing and the software will pop out the following
hint:
Select [Yes (Y0) or [No (N)] according to what the actual LED display
screen indicates and the following hint will appear after selection:
57
After clicking [Enter], adjust the following different kinds of
parameters according to the actual situation, as the following figure:
Click sending after finishing adjustment and reset is carried out again
after DBA-9.0 saves the parameter. The software will exit, as the
following figure:
DBA-9.0 parameter setting is hereof finished.

◆ Manufacturing and sending of the program
Return to the playing interface after exiting setting, illustrated as the
following figure:
58
Then click [New] and the following figure will appear:
Select [ARM9 special program list]

Click [Ok] after confirming the size of the screen and you will see the
following figure:
59
Set according to your need and select the single or multiple windows.
Suppose we select forth window to edit, click arrangement distribution
(2*2) and the following figure will appear:
You start to adjust your window and set the window you need. What
you need to pay attention to is that the windows within the same panel
are not allowed to overlap, or it will be issued wrongly. Then add the
program you need in each window and you can click start menu to
preview the next effect after finishing adding, illustrated as the
following figure:
60
Under the circumstance that no problems are possessed, the program
can be directly sent to DBA-9.0 and select [Send to AMR9…] in the
control menu, as the figure below:
The software is able to switch the program automatically. Select the

DBA-9.0 IP to be sent and click [Send] after finishing switching the
files. (The software is able to support 254 DBA-9.0 to the utmost to
send program at the same time for each time), as the following figure:
The following figure will appear to select the storage media after
clicking [Send]
end]:
61
Click [Enter] after selecting the type of the memory card and the
software will send the program to DBA-9.0. The program hereby has
finished sending.
Section II DBA-7.0 asynchronous control

system
2.2.1 Hardware recognition
2.2.2 Function characteristic

◆ Each image can set the roll message or not, or the roll message can
be set on an interval basis.
� The display of 36 kinds of stunts and clearance stunts respectively
can be supported.
� The playing of unicolor, double color and full color picture is
supported.
� BMP, JPG, ICO, DIB, EMF and other kinds of picture formats as
well as the files and GIF, AVI, MPG animation are supported.
62
� Text editing is supported.
� The interface of the software is in simple and convenient
operation.
� Timely playing can be realized.
The external interface is supported such as temperature, humidity,
clock etc.
2.2.3 Software introduction and application explanation

Firstly, select the installation package according to the matched optical
disk and then click it to install according to the defaulted hint until
successful installation appears. The desktop will appear after successful
installation
Double click the icon and the main interface of the software operation
will appear as the following figure:
It can be divided into: Menu bar, tool bar, program list, edition area and
status bar according to the function area.
2.2.3.1 Software introduction

[Menu bar]
File, editor, remote, options and help are included.
63
[Tool bar]
They are new, open, save, send, exit, program, image, Picture Movie
Multext T Roll Msg copy, paste, cut, and delete respectively.
[Status bar]
A very useful status hint bar is situated in different editing statuses and
displays the corresponding information.
[File] menu contains six menu items illustrated in the following figure.
New establish: it is used to establish a new LED program list

Open: it is used to open the LED program list which has been edited
previously.
Close all: it is used to close and delete the LED program list.
Save: It is used to save the current LED program list.
Saved as: It is used to save the current LED program list in other files.
[Additional function] Menu contains the following eight menu items
2.2.3.2 Software application

◆ Click [New]
ew], which means establish new program list, and then the
following picture will appear:
64
◆ Click [Control card] in the [program list] and the following figure
will appear.
◆ Click [Base parameters] to carry out the setting of the basic

parameter
[Name of the card] Is the name of the LED big screen, and the
defaulted value can be saved or edited according to the actual situation.
65
[TCP/IP address] Is the TCP/IP address of DBA-7.0 control system.
[Size] Is used to establish the length, height and color of the LED big
screen, and the parameter list is as follows:
Dimensions Full color Double color Single color
parameters
Length （Pixel point） ≤256 ≤512 No
Height （Pixel point） ≤128 ≤256 No
◆ Click [Advanced 1] to carry out the setting of the senior parameter
[OE signal] Is the polarity of OE, [Negative] means OE is low (This is

0) and effective, [Positive] means OE is high (That is 1) and effective.
[Driver] The instant current source is the effective illumination when
the data is 1 (such as TB62726) and the rest is the effective illumination
when the data is 0
[Color group] The color order when it is under the full color.
[Clock data clock duty cycle] has not been open to the user at present
and it is the data clock duty cycle with 25% defaulted value.
[Gray scale] The gray selection of the screen can support 4,096 grade
gray which is at the most for the full color screen and the double color
screen. The users can set it according to their own needs.
[Line-close time] The selection of the de-shadow effect means the
de-shadow pulse width and the user can set it according to their own
needs.
[Clock frequency] Means the frequency of the data clock frequency
and the users can set it according to their own needs.
[Effective scan] Means the position of the first line of data of the scan
screen and the users can set it according to the actual situation.
66
[Scan mode] Is the scan mode of the screen and the users can set it
according to the actual situation.
[Brightness grade] Means the brightness of the screen and the users
can set it according to their own needs.
[Line height] Means the one in each area, which is illustrated in the
following example:
Example 1: 1/8 scan, 16 rows for each area. The signal trend is as the
following figure:
The parameter is hereby set as: the scan mode is eight scan, post
high/each group of data selects 16 rows, Z reentrant selects eight lines
of reentrants.
◆ Click [advanced2]] To carry out setting of senior parameter 2.
[Row inverse parameters] Means the direction where the data is

driven and it is the normal method when driving from upper to lower
and vice versa, then the row order needs adjusting. How many reverse
67
will be selected is subject to the post high and scan mode of each area.
2 row reserves mean the mutual reverse while 4 row reserves means the
reverse of every two rows following with the other rows. The following
are the two examples:
following figure:
The parameter is hereby set as: The scan mode is 8 scan, post high/each
group of data selects 16 rows and the adjustment of the row order
selects 16 row reverses. Z reentrant selects eight lines of reentrants.
following figure:
The parameter is hereby set as: the scan mode is four scan, post
high/each group of data selects 16 rows and the adjustment of the row
order selects 16 row reverses and 8 row reverses. Z reentrant selects
eight lines of reentrants.
[Column inverse parameters] Means the order of each bit. 2 line
reverses means the mutual reverse in two lines while 4 line reverses
means the mutual reverse of every two digits one after another. For an
8-digit data as an example, the order of its screen is 7-0, the order will
68
be adjusted as: 2 line reverses, 4 line reverses and 8 line reverses. The
realization process is as follows:
First with 8 line reverses, the order will be changed into: 3 2 1 0 7 6 5 4
Following with 4 line reverses, the order will be changed into: 1 0 3 2 5
476
Following with 2 line reverses, the order will be changed into: 0 1 2 3 4
567
[Row or column return] and [S tandard reentrant] are the direction
of the data transfer. If one row transfers to the bottom, it would be one
row reverse while if there are two, it will be 2 row reverses when
returning and so on. The user can set it according to the actual situation
of his/her own screen. The example refers to 1 and 2 of the senior
parameter 2.
Note:
The scan mode of the screen and the post high of each area shall be
value..
integrated for observation when setting the reentrant value
Example 1: 1/4 scan, 4 rows for each area, the signal trend is as the
following figure:
Z reentrant option is invalid at this time and it will be valid in case of 8

rows for each area.
[U reentrant] selects whether the U type reentrant is possessed and the
users can set it according to the actual situation of their own screen.
Note:
The scan mode of the screen and the post high of each area shall be
integrated for observation when setting the U type reentrant.
◆ Click [Picture group] in the [Program list] and the following

picture will appear:
69
○ Click the [Image] button on the [Tool bar] or right click [picture
group] to add pictures.
The same method can be applied to adding animation file (Gif, mpg and
avi) and files with text format. Only by selecting the file path in the
editing area of the picture setting on the right side, can the modification
be carried out.
○ After selecting the file, edit the property (Enter the stunt, exit the
70
stunt, moving speed, stay time and cycle times etc.)
The stunt table is as follows:
[Stay time] means the interval time from finishing displaying when
entering the stunt to just exiting the stunt.
◆ Click [Roll message
message]] in the [Program list] and the following
picture will appear.
○ Click [Roll message] button in the [Tool bar] or right click [Picture
group] to establish new roll message.
71
[Font] Is used to set the font of editor text area
[Size] Size for the font, there are 12、16、20、24、32、40、48、64、
72 etc.
[Color] Establishes the color of the text font.
[Background color] Establishes the background color of the text.
[line] is defaulted as being standard, which means 0 point row spacing.
[Overall pages] The number of the pages of the output text, which
means carrying out cutting according to the screen size (such as 128*
96)
[Current page] Is used to browse the display situation of each page.
[Size of the picture] Is used to set the length and width of the screen.
[Open] Button is used to open the files which have been edited before.
[Save as] button produced the files of imf, rol, BMP etc. according to
the need.
[Close] Button is used to close the dialogue box.
72
[Display mode] There are transparent display and covered display.
When it is under transparent display, the roll message will display
transparently without background color which can not be established.
When it is under the covered display, the background color can be
established.
[Background color] Establishes the background color of the roll
message and setting can not be carried out when the display mode is
under transparent display.
[Width] The length of the screen is set automatically.
[Height] Is fixed as 16.
coordinate]] Is fixed as 0.
[X coordinate
coordinate]] Dereferencing scope as: 0~（height of screen body -16）
[Y coordinate .
time]] Dereferencing 0-65535, value the larger and the lower.
[Dwell time
[Movement speed] Dereferencing 0-65535 ， value the larger and the
lower.
index]] Dereferencing 0-65535.
[Cycle index
Note:
The roll message is the global program and no matter how many
messagess are possessed, each screen will display on an overall
roll message
basis by selecting the send property.
73
◆ Flow of the clock, temperature and humidity manufacturing
Click [Global customization information] in the [Program list] and
will display the following picture:
◆ How to play the programs regularly (Only 10 programs can be

played regularly at present)
Click [Program 1] in the [Program list] and the following
picture will appear:
The time limit is edited according to the actual situation.

◆ New version ARM7-E
74
The difference between the new version ARM7-E and ARM7: it is
identical on the perspective of the hardware while the difference lies in
the software, as the following figure:
○ The new version ARM7-E has added the intelligence of the parameter
setting, that is “intelligent setting" the process of which is the same with
that of DBA-9.0(ARM9).
○ The parameter setting of the new version ARM7-E separates with the
program sending independently to avoid the previous constraints of
sending the parameter together with program. The abnormal display of
the screen will be caused when sending the program under the
circumstances of not knowing the parameter.
Section III Video processor

2.3.1 Points for attention for safety
Danger!
There is high voltage within the machine and the non-professionals are
not allowed to open the machine cover to avoid danger.
Warning!
1. The equipment is not allowed to be splashed by water drop or water,
and place the articles with liquid.
2. The equipment is prohibited to get access to the fire in order to
avoid fire.
3. At least 20CM gap shall be left around the equipment for the
purpose of adequate ventilation.
4. If the equipment produces serious noises, fume or peculiar smell,
the socket shall be pulled out immediately and contact with the
supplier;
5. It is prohibited to pull in and out of HDMI/DVI signal cable with
75
electricity.
Attention!
1. Please read the instruction carefully before suing and take care of it
for back up;
2. Please pull out of the socket of the power under the circumstances
with lightening or without use for a long time;
3. The product is not suitable for the operation and debugging by the
non-professionals and the user needs the guidance of the
professionals;
4. Never stuff any materials to the via hole of the equipment to avoid
damage of the equipment or electric shock;
5. It is not suitable to locate the equipment near water or other
humidity place;
6. It is not suitable to place the equipment on the fin or other place
with high temperature for application;
7. Under the circumstances of using HDMI cable, one section of wire
from the HDMI port is not allowed to suffer from the external
force.
8. The socket of the power shall be pulled out of and someone shall
be entrusted for repair in any of the following cases:
○ When there is liquid splashing into the equipment;
○ When the equipment falls down or the crate is damaged;
○When the equipment occurs something abnormal or the
performance changes;
9. There is no components to be repaired within the video processor
and please do not open the crate and we are not responsible
for the results by opening the crate arbitrarily.
10. Please keep certain distance with other equipment to facilitate
operation and ventilation.
11. Please never pull in and out of different signal wires with electricity
in any of the situations.
2.3.2 Hardware connection

1. The signal port graphic of the back panel:
2. Port explanation
◆Signal input
DBT-Q09 video processor supports the input of six kinds of signal
76
sources, among which:
[HDMI1] the digital signal input of 1 circuit computer (PC)
[HDMI2] high-definition digital signal input of 1 circuit
[VGA] analog signal input of one circuit computer
[YPB/PR] high-definition component video input of one circuit
[CVBS] PAL/NTSC compound video input of one circuit
[S-Video] PAL/NTSC system bright color separate video input of one
circuit
◆ Signal output
[HDMI] The digital signal of one circuit computer connects with the
display equipment with DVI digital interface.
[VGA] The analog signal of one circuit computer connects with the
display equipment with VGA interface.
[1, 2, 3, 4, and RJ45 interface] The function of 1 and 2 ports shall
refer to HVT-07; 1 and 3 ports display the same content while 2 and 4
ports display the same content.
◆ Communication control
USB interface: Serial communication control input
2.3.3 Schematic diagram of the system connection
2.3.4 Explanation of the keyboard key-press:

◆ Schematic diagram of the front panel:
77
◆Key-press
Key-press explanation:
○ Shift key:
shift
Key-press status switch: there are three key-press statuses in this
equipment and they are: the first function, the second function and the
third function respectively. Shift is used for the switch among the
functions and it is defaulted as the first function when starting up. Three
red lamps correspond with the instruction of the first, second and third
function from top to the bottom.
Under the mode of the first function:
1．Selection key of inputting the video source
Key
Selection of the video source:
DVI-A: selects the HDMI1 (PC) signal input
DVI-B: selects the high-definition digital signal input
VGA: selects the analog signal input of the computer
S: selects PAL/NTSC system bright color separate video input
Yp: selects high-definition component video input
AV: selects the analog signal input of the computer
Note 1:
The selection of the major and minor window sources:
Two association groups of the picture-in-picture mode are as the
figure above. If one input source in the association group 1 is
selected, it will be deemed as the major window while the
association group 2 will be the minor window for the last choice.
Similarly, the selected source is in the association group 2, the input
source will be the major window and association group 1 will be
selected as the minor window in the last choice. There are
altogether 18 kinds of such combinations of the major and minor
windows the signal of which cannot select two signals in the same
78
association group at the same time.
2. Up and down key:
Key
They are used as the brightness adjustment of the major window.
DOWN: reduce (Decrease) the brightness value of the major window.
UP: increase the brightness value of the major window
Note 2:
The adjustment scope of the brightness is: 0-99 grade and the
continuous adjustment can be carried out by pressing constant
value.
3. Parameter key of the image display:
Key
S1: S1 owns two kinds of functions and Function a occurs when
pressing for once while Function b comes out when pressing for the
second time and they are:
a) Full screen display of the major window
b) The size of the system window recovers to the user-defined mode
of the user
a) Picture locking of the major window
b) Locking rescission of the major window picture
a) Picture FILL of the major window picture, that is: the major
window picture fills with the area of the major window size
b) Picture FILL of the minor window, that is: the minor window fills
79
with the area of the minor window size
a) The picture of the major window 1:1 that is: the picture of the
major window displays as the actual size of the vide source signal
b) The picture of the minor window 1:1, that is: the picture of the
minor window displays as the actual size of the vide source signal
Under the mode of the second function:
Key
1) Brightness, chroma, saturation and contrast
DVI-A: the brightness reset of the minor window
DVI-B: the brightness reset of the major window
VGA: the saturation of the major window
S: chroma of the major window
Yp: the contrast of the major window
AV: not opened temporarily
DVI-B and DVI-A are the shortcut keys of restoring factory setting of
the major and minor window respectively and the factory brightness
value of the corresponding window will be recovered by pressing the
key.
Note 3:
The adjustment mode of the brightness, chroma, saturation and
contrast:
The value is increased by pressing UP key and decreased by DOWN
key after selecting VGA (Saturation of the major window) or Yp
(Chroma of the major window) or AV (Contrast of the major
window). The value can be adjusted continuously by pressing UP or
DOWN key for a long time.
Under normal circumstances, the brightness, chroma, saturation
and contrast have been adjusted to the standard status before
delivery and the following adjustment thus becomes unnecessary.
Key
80
The value adjustment is carried out by the coordination of other
function keys under the appointed function. UP key can be used for
increasing and DOWN key for decreasing to carry out adjustment when
the width, length, Y coordinate of the starting point and X coordinate of
the starting point etc. are selected, for example, Note 3.
Key
S1: S1 also owns two kinds of functions. Function a works when
pressing for once while Function b works when pressing for the second
time and they are:
a) Height selection of the major window
b) Height selection of the minor window
S2: S2 owns two kinds of functions. Function a works when pressing
for once while Function b works when pressing for the second time and
they are:
a) Width selection of the major window
b) Width selection of the minor window
a): Coordinate in Y direction selection (Starting point) of the major
window
b): Coordinate in Y direction selection (Starting point) of the minor
window
a): Coordinate in X direction selection (Starting point) of the major
window
b): Coordinate in X direction selection (Starting point) of the minor
window
Under the second status, after being selected, S1, S2, S3 and S4 can
coordinate with UP key and DOWN key to change its corresponding
value respectively for the purpose of changing the coordinate of the
screen size. The width of the two windows in the equipment can not
surpass 1, 024 at the same time with 1, 280*1, 024 display input
resolution.
Under the status of the third function:
S1: recovers the restore factory setting of the key-press board and 4*4
81
matrix red lamp will flash for 7 times and the reset is finished by
pressing S1 key for more than 10 seconds. The system needs powering
up after resetting the system.
S2: recovers the reset of the video system.
Note:
When the adjustment data is lost or in disorder for the reasons
unknown, resulting in the failure to normally display the image of
the system, you can recover the data when delivery by means of
initialization operation and then adjust according to the setting
explanation above.
2.3.5 Operation case

Operation case
Connect the peripheral equipment including input source (6 circuits at
least connects one circuit of source and HDMI interface connects the
computer by opening [Copy mode],) (The case takes computer source
HDMI 1 port and AV two circuits channel as an example), output
source USB.
1. Open DBT-Q2009 power and it is defaulted as the first status when
starting up. Press HDMI1 on the panel and observe whether there are
some changes (controlled) NOT1 on the image of the LED screen or
[Output external display] and press S3 key for twice.
2. Press [SHIFT] key for once to come into [Status of the second
function] (the small liquid crystal display on the right can be seen or the
second lamp of the red lamp indication will be bright)
� Press the liquid crystal on the right side of S3 [Y starting point of the
major window] and there will be Y value displayed. “UP” can be used
for increasing the value of the coordinate while [DOWN] key for
decreasing the value of the coordinate with the defaulted value “0”.
� Press S3 [Y starting point of the minor window] again, the Y starting
point of the minor window is adjusted by the coordination of “UP” and
“DOWN” key.
Similarly, S1, S2 or S4 coordinate with “UP” and “DOWN” key to
adjust the size and coordinate of the corresponding windows
respectively; press “DVI-A” or “DVI-B” or “VGA”, “S” or “YP” or
“UP” and “DOWN” key can also be used to adjust the setting of the
contrast, saturation and other parameters of the corresponding major
window. (The specific function under the second status refers to the
function explanation of “under the mode of the second function”)
1. [ SHIFT] Key is used to enter “the first function mode” and press
S3, “FILL” S4 “1:1” for adjustment. Pressing once means the major
window while the minor window will come out by pressing for the
82
second time.
2. The switch of HDMI1 and AV between the major and minor
windows can be conducted by finishing the 3 procedures above. The
major window will display the content of AV by pressing AV while the
minor window displays the content of HDMI1. When pressing the
HDMI1 content that the HDMI1 major window displays, the minor
window will display the content of AV. In this way, the switch of 2
circuit source can be realized. If there is the switch of the source of
more circuit, we only need to select the corresponding channel first and
then adopt S3 and S4 to set the corresponding channel as “FILL” or
“1:1”. When we setting the parameter of the “corresponding channel”,
there must have video input on that (the content of the channel shall be
output), only in this way, can the parameter issued respond.
3.
NOTE: If the output external display is connected, we can make a
judgment on whether the equipment is under control by observing
whether the content of the display has changed or not. If the
external display is not connected, we can carry out judgment by
means of LED electronic screen.
a. Black screen of the electronic screen

1. Under the normal circumstances, the output yellow lamp of RJ45
port of the receiving card is connected, the green lamp will be bright
always. On condition that the yellow is bright while the green one is not,
it means that the receiving card has been connected with the lack of
data, please confirm the connection of the video source and HDMI
needs to open the copy mode.
2. The data flash of the receiving card is still in black screen and inspect
whether the parameter of the receiving card is correct; the too small
screen displays that the position coordinate has deviated and inspect
whether the resolution of the display card is 1, 280*1, 024 or not. Or
press S3 under the mode of the first function and press S1 to see
whether there has displayed or not. The setting and adjustment can be
carried out by the coordination of the software according to the
explanation when there is display.
3. Inspect whether the source channel is selected correctly and whether
what has been played is DVD. Some videos own the black edge on the
upper and lower side.
4. Please contact with us if there is still something unclear.
b. The picture of the window is not clear
Please inspect the resolution of the computer and 1, 028* 1, 024 mode
is entailed.
83
84
Chapter III Multimedia program and
playing
Section I: Summarize
3.1.1 Function characteristic
Designed by the professional working group of LED studio device,
XMPLAYER LED studio device is a set of device specially designed for
the program manufacturing, playing software and supporting files of
many format: text file, WORD file, all the picture file
(BMP/JPG/GIF/PCX...) and all the animation files （MPG ／MPEG／
MPV ／MPA／ AVI／ VCD ／ SWF／ RM ／RA ／ RMJ／ ASF ．．．）
with the characteristic of the strong function, convenient application
and being easy to learn.
3.1.2 Operating environment

Operating system
Chinese and English Windows98/me/2000/NT/XP
Hardware configuration
CPU: Pentium above 300MHz
Memory: 64M
Video card: Standard above VGA 256 display mode
Related software
Windows Media Player from Microsoft (MediaPlayer) -- must be
installed
OFFICE2000-- If necessary, the WORD file must be installed
RealPlayer---Installation is entailed when Realplayer file needs playing
Section II Installation and unloading

3.2.1 Installation
The software installation of XMPLAYER LED studio device is easy and
the operation is as follows: insert the installation optical disk of the
LED studio device to the CD-ROM of the computer and the catalogue
the optical disk locates in will pop out immediately (if it does not pop
out, double click the optical disk after selecting), illustrated as Figure
2-1.
(Figure 2-1)
85
The selectable installation guidance will appear after double clicking
[Autorun. exe]
[XMPLAYWE]] is required.
[XMPLAYWE
After selecting [Xmplayer] item, click the installation button on the
lower right side and the following figure will appear after that:
If only Chinese and English are needed to install, installation can be

carried out after selecting [English] or [Chinese]
[Chinese]. If you intend to
change the installation catalogue or other languages, select
button and the following procedure will appear:
Firstly: select the installation path
86
Secondly: Select the language category
Thirdly: Select the installation button
87
It is defaulted as installation when the following interface appears
during the installation process and operation according to the following
procedure. Please confirm the operation when defaulting on an overall
basis.
88
89
After the successful window
will appear, the icon and start->

procedure ->DBstar, then the following icon will appear
The procedure can be operated

by operating xmplayer icon.
3.2.2 Unloading
XMPLAYER LED studio device software offers the unloading function
to allow you delete all the files, procedure group and shortcut of
XMPLAYER LED studio device on a convenient basis. The user can
click [Start ->procedure ->DBT-Qstar->UnInstall, the LED studio
device will be unloaded] (Method 1 figure). Select [Add/delete
procedure] in the [Control panel] for fast unloading. Unloading
(Method 2 figure), all the files, procedure group and shortcuts can be
unloaded by selecting automatic option at this time.
Figure of Method 1:
90
Figure of Method 2:
Section III Specific explanation for

application
3.3.1 Program composition
One program is composed of several subprograms which contains many
program windows and these windows are used to display the text,
picture, animation, segment of the multimedia and other contents that
the user intends to play and they include: text, editable text, table, clock,
analog clock, website page, sensor, Word and Excel files etc.
3.3.2 Introduction of the interface window
The operation interface of the XMPLAYER LED studio device software
is illustrated as Figure 3-1: there are two windows altogether: playing
window (The default will not be displayed at the beginning of starting
until new establishment0) and control window (Figure 3-2).
91
Figure 3-1
Figure 3-2
92
◆ Playing window
The playing window (This is the content displayed on LED screen) is
used to display the text, picture, animation, and segment of the
multimedia and other content that the user intends to play. The content
here is synchronous with that displayed on the LED screen and the
software supports multiple playing windows.
◆ Control window
The control window is used to control the place and size of the playing
area as well as the content to be played and it can be expanded into
edition window. It also contains menu bar, tool bar and edition control.
The control window with edition is as follows:
Menu bar: including file, edit, play, control, tool, ducument and help the
seven submenus.
Tool bar: is the fast operation of the menu function.
Edition control: is divided into two parts, the left half is the program
selection which displays the program and the information of the
subwindow while the right half is the control option which controls the
playing stunt and time etc. of the program.
3.3.3 Function introduction
3.3.3.1 Menu bar: including file, edit, play, control, tool,

document and help
help。
93
◆ File menu, illustrated in Figure 3-3 and it contains new establish,
open, close, save, save as, save with materials, save all, release, send
the current program to FTP, language and exit.
New establish: Is used to establish a new LED playing mode (ARM9
and ARM9V2.0 and synchronous distinction).
Open: Is used to open the files of the LED studio device which have
been edited before.
Close: Is used to close and clear the current studio files of the player.
Save: Is used to save the current files of the LED studio device.
Save as: Is used to save the current files of the LED studio device as the
new files of LED studio device.
Save with materials: Is used to save the current files of the LED studio
device and save the materials in a materials base.
Save with materials: It is used in DBA-9.0 system. When DBA-9.0
system owns 1 server to manage and send the program and the server is
needed or the computer is reviewed to carry out the content to be sent,
the control computer will save both the program list and materials into
the review computer. After it is confirmed by the review computer,
review computer is used again to send to DBA-9.0 system for playing.
The schematic diagram of the system is as follows:
94
Special explanation:
1. There is a sharing catalogue for each server corresponding to
the area of each set. The number of the sharing catalogues is
subject to the set number.
2. After finishing editing the content to be played, the area
computer will copy the program list and file to the catalogue
corresponding to the server.
3. After finishing reviewing, the review computer will directly
send to each display screen.
4. The area computer is only responsible for sending to the server,
which is the unidirectional communication. The review computer
and server are both bi-directional communication.
5. At most 255 display screens can be connected in each
corresponding network section.
Save all: The manufacturing and broadcasting device supports multiple

screens and program lists at the same time. When several LED screens
are being manufactured at the same time, press [Save all] all], and the
system will save all the work with the format *.XMP. Meanwhile
opening in the next time, several LED screens will be opened and
displayed under “program list” of the menu bar. Issue: is used for
DBA-9.0 system. When the network is used to issue content to
DBA-9.0 and if the files are quite small, the transmission speed will be
very fast. If it is in the type of the video file, the time for sending will
be relatively long. At this time, what needs doing is to insert the storage
(U disk, SD card or CF card) used by the DBA-9.0 to the computer by
means of the mobile card reader and “issue” the files which has finished
95
editing to the storage, then insert the storage to the slot corresponding
to DBA-9.0 and normal playing thus can be carried out.
Language: It is used to select the language needed and there are
simplified Chinese, traditional Chinese, English, Japanese and Russia at
present. In the core design of the manufacturing and broadcasting
device, what we all adopt is the module design and if the user needs
certain kind of language, what they need to do is to add the module of
the language to the system. The specific operation method refers to
modification]. The reason why the
[Introduction of the language modification]
three smell graphics in the frame is for the interface left for the users
about the module of the language.
Note:
Windows XP simplified Chinese operation system is taken as an
example. If the user intends to select traditional Chinese, the menu
bar and Chinese characters in the software will change into clobber.
If such phenomena happens, please select [standard and format] of
the [area option] panel within [control panel] and [area and
language option] as [Chinese (Taiwan)] and select [Language of non
Unicode procedure] within [Senior] as [Chinese (Taiwan)], then
press [Enter] to restart the system. The application mode of other
languages is the same with this and during the transformation
process, if the procedure belongs to the copy version instead of the
installation version, please remove the Chinese name of catalogue
where the file stays, otherwise the system will not recognize Chinese
character, resulting in the failure to operate the software.
Exit: it is used to exit LED manufacturing and broadcasting device.
Note:
Please save the work you are editing before exiting and after the
software exits, the system will not save the current work and only
the choice of open or new establish is accessible when entering the
system again.
Save all: It is used to save all the current studio device files opened by
the player.
Language: It is used to switch language (Simplified Chinese, traditional
Chinese, English, Japanese, Korean etc. are supported at present).
Exit: it is used to exit the LED studio device.
Canceling LED studio device: Lock LED studio device (The mouse and
keyboard can be locked).
96
◆ Edition menu:
Just as Figure 3-4, it contains add (insert file…, material base…, Flash,
picture, multimedia, clock, video input, digital clock, website page and
text etc.), delete, cut, copy, paste, move forward, move backward, hide
the edition content, refresh, place (the place of the current window in
the screen) and size (the proportion that the current window accounts
for in the screen).
◆ The play menu contains start, pause, stop and mute, illustrated as the
following figure:
97
◆ Control menu:
It contains LED control setting, DBA-9.0 LED control equipment, send

to DBA-9.0, screen combination, current setting (Setting I…Setting
XII), load the combination parameter of the screen, save the
combination parameter of the screen, refresh LED control, display
explore option before searching LED control equipment, start big
screen, freezing of the screen picture, test, option and set information of
LED control.
Setting of LED control card…: different parameters of the LED main
control card and screen of the display screen can be set and the second
part of the technical support manual is about the specific explanation
and introduction of the hardware setting of the control card.
DBA-9.0 LED control system…, adding the IP address of the remote
equipment is used to control the DBA-9.0 embedded control system of
our company and the third part of the technical support manual is about
specific explanation and introduction about the setting of the DBA-9.0
embedded asynchronous control system.
Sending to DBA-9.0…: when selecting to manufacture DBA-9.0
professional program list, the asynchronous sending is valid and click
to send parameter to ARM controller. The third part of the technical
support manual is about the specific explanation and introduction about
the DBA-9.0 embedded control system.
Screen combination: it is used when the user owns several display
screens for separate display and requires each display screen indicates
98
different content or the content of each display screen needs to form a
perfect content. It shall be combined with [current setting]
setting].
Current setting: it is used by associating with [screen combination]
and 12 kinds of combination modes are possessed at most. The shortcut
keys such as “Ctrl+Alt+F1…F12” are used to switch during the
broadcasting process.
Note:
The interval between switches shall be no less than 5 seconds.
Combination parameter of the loading screen: transfer the combination

parameter of the screen which has been established previously for the
purpose of fast application and the format of the file is ＊.ropt.
Refresh LED control…: When the compute connects with the
synchronous or asynchronous control system, it will be used to refresh
the software so as to find the new connected synchronous or
asynchronous (DBA-9.0) control system.
Display explore option before clearing LED control equipment: tick
“√” before the item and the explore interface will be displayed when
opening the software, on the contrary, the explore interface will not be
displayed and directly enters the playing software.
Start big screen: It is used to send the parameter to make the LED
display screen open or close. When the option is under closed status,
only making the screen black is ok. If the power of the display screen
needs closing meanwhile shutting down the display screen, a power
control board is needed to connect externally. The specific situation can
refer to the second part of the instruction.
Note:
If the software intends to start the code protection function, press
[Start big screen] after inputting the correct code for the first time
Freezing of the screen picture: when the player is playing, the static
screen picture become optional and the screen picture will be static
when clicking it, which is equivalent to the function of [Lock the
screen]
screen].
Test: the desktop of the computer will become the cursor in cross shape
(Related to Chinese characters) after clicking and this item is used to
adjust the place where the display screen indicates and the gray scale of
the display screen for the convenience of the debugging of the clients.
There will be hints about the application method of the test on the
desktop.
Option: Click [Option] and the player can be set to start together with
99
computer, load the program list automatically when starting, change the
position of the mouse when starting, confirm when deleting/exiting,
hint for save when closing the program list, record studio/system log,
reserve log and other options.
Note:
The log file is saved in xmplayer\log catalogue in the system with
the format of [*.TXT].
Open the power management: it is used by combining with [power

management] within [LED control setting]
setting], which is equivalent to be
the shortcut of [power management] setting. It works by ticking [√]
before [Power management]
management]. The application method is the same with
[Power management] within [LED control setting] in the second part.
◆ Tool menu:
It contains subtitle, notification, sports score, playing PowerPoint

document, allowing the remote control of the machine, starting remote
control, playing DVD, VCD or CD, Word document translocation
graphic, new establish of Word document and listing all the files.
◆ Menu of the program list:
The menu list mainly lists the current playing list that the player opens
or the current new file playing list and the playing of several programs
100
can be realized by switching the item. The following figure illustrates
more specifically,
◆ Help menu
After the panel appears, the code setting frame will appear by pressing
[Ctrl+Alt+D], illustrated as the following figure:
[Ctrl+Alt+D]
Set the time (Date) to be locked in the [Lock time] frame and an 8-digit
code shall be set within the back code frame. Press [Enter] to restart
101
the software and the code becomes valid. When opening the software
again after the appointed time, the system will hint to input code and
the software will work normally after inputting the correct code. The
system supports five groups of codes altogether.
Note:
1. Please remember the code when the software has set it and once
the code is forgotten, the system has to be sent to the company.
2. When setting code, never use the same code.
3. After restarting, [start big screen] under [control] menu has to
be pressed and then the system will work normally.
2.3.3.2 Tool bar

The defaulted tool bar is as the following figure:
The tool bar is the fast operation of part function in the menu and they
are from the left to right: New establish, open, save, close, play, freeze,
open the screen, add, delete, cut, copy, paste, move forward, move
backward, refresh and exit.
It is as the following figure after playing operation:
What the tool bar arranges from the left to right are: pause, stop,
manual, hide, top, background, mute, freeze, open screen, close and
exit.
◆ Flow of the program manufacturing
○ The first step: Set the size of the playing window
The size of the playing window must be set correctly, otherwise only
one part or not big enough space will be displayed when the program
finishes manufacturing and starting playing.
There are two kinds of setting methods:
The specific procedure is as follows:
New establish (New establish on the tool bar or menu -> file->
102
new establish ), the following figure will appear:
(Figure 3.4.1)
Fill in the value of the left side, top, width and height according to the
needs and finally .
103
(Figure 3.4.2)
The second kind: the client can bind the size of the screen for setting, in
this way, the size and place of the screen will be achieved automatically
(The premise is that the user has established it), finally .

The specific procedure is as follows:
○ The second step: new establish program list

(Figure 3.4.3) will appear after setting the size of the window.
Firstly, select different program types according to the needs of the
clients to the format of the window and the system has provided the
program type with seven formats to facilitate the selection of the
clients.
104
Figure 3.4.3
Figure 3.4.4
The program list is composed of LED screen, several programs,
subprograms and program windows.
Left click [LED screen] and the property table will be displayed:
105
Left click [Program] to display the property table:
Left click [Subprogram] to display the property table:
Left click X [Program window] to display the property table

X: represents the serial number of the window of the subprogram under
the subprogram, for example: 1 [Program window]
○ The third step: Option of setting the program window

106
The figure below illustrates the new-established program window with
name, place, size of the program window, frame type, frame color,
background color of the frame and the transparency of the subwindow.
○ The forth step: adding program materials
The program window seems like a container and it can play different
inserted files, Flash, MS Excel file, MS Word file, Real media, sensor
display, multimedia, simple table, editable text, analog clock, screen
copy, video input, digital clock, picture, website page and text etc. there
are dozens of materials to be selected and the program selection menu
as the figure above will be popped out after right
clicking to explain the materials
respectively.
File window: Is the most important window and all the supported files
can be played in this window. Files as many as imaginable can be added
in the window and there are more than ten kinds of supported file
categories. The specific type is as the following figure:
107
Text: It is used to play the text files and the character format is the
same.
Simple table: It is used to edit the data of the playing table.
Digital clock: It is used for timing and count-down of the clock (Digital
format).
Editable text: It is used to edit the data of playing rtf format.
Video input: It is used to connect with the external video equipment
such as TV card and TV box.
Multimedia: It is used to play the video file with the mainstream format
at present.
Website page: It is used to play the files of HTML and other website
page format.
○ The fifth step: Setting the option of the program materials
The property is modified after adding the materials according to the
needs, for example, adding Flash file, and editable text:
Figure 3-27
○ The sixth step: finishing program manufacturing
The manufacturing of one program page has been finished by the five
procedures above. If more program pages are needed, please repeat the
step from the second to the fifth. Do not forget to save after finishing
manufacturing the program page. Click the save button or

select the menu file-> save.
○ The seventh step: the playing program shall play the current program
files, click the tool bar (or) play the button to start playing,
108
pause, stop or select from the control menu. When
playing different program files, click open button and playing

will be conducted after opening the program file.
Section IV Edition of the program materials

3.4.1 Operation of the project bar
◆ [LED screen]
screen]: Click [LED screen] of the project bar and the
display will appear the following panel:
The name of the LED screen, background color of the screen, the width
of the subwindow and other information can be customized within the
property bar at the right side of the panel and the user can set them
according to the actual need. The display coordinate position, width and
height of the screen will not be changed generally. The bidding setting
of the control card can make each [LED screen] realize the function of
controlling several display screens by the control card binding one
corresponding display screen.
Note:
The playing software supports not only the edition of the single
LED screen but also the simultaneous edition of several LED
screens.
◆ [Program]
rogram]: Click the [Program] in the project bar:
109
The name of the program can be customized by the area of the basic
name at the right side of the property bar and the playing mode, ending
mode and the setting times/time can be selected when playing. The
playing mode includes order playing, timing playing, overall playing,
manual playing and inserting playing.
Order playing: The program is played according to editing order.
Timing playing: After selecting the timing playing, the regular setting
option become selectable and the following window will pop out by
clicking the blue arrow button at the right side of it. The parameter is
set according to the actual need and then click add to list the set
parameter to the program time and click enter key.
Overall playing: Once the overall playing is selected, the program will
remain in the playing status during the whole playing process.
Manual playing: If the program is set as the manual playing, it will be
played only when clicking it.
Ending mode: The playing times/time you set will be deemed as the
cycle and [Program] here (Including all the following [S ubprogram]
ubprogram])
will be played on an orderly basis.
110
Note:
1. The value of the playing times/time is the actual seconds.
2. Under the circumstance that the normal playing can not be
carried out, please confirm whether your program has been set
regular option first.
Inserting playing: if other content needs inserting during the process of

normal playing, this type can be selected and such program will start
playing by selecting it and click manual when playing.
◆ [Subprogram] click the [Subprogram] in the project bar and it will
be illustrated as the following figure
The name of the subprogram can be customized within the property bar
at the right side of it, meanwhile, the subprogram list can be divided
into several subwindows according to the needs of the clients; or the
ending mode of the subprogram and the times/time of setting can be
selected by clicking the blue arrow button.
◆ [S ubwindow] click the [Subwindow] in the project bar and it will
be illustrated as the following figure
111
The type, color and background color of the frame of the subwindow
can be set in the property bar and other items such as the display
coordinate position, width and height of the subwindow needn’t setting
generally. The transparency of the subwindow is strengthened gradually
from 0-100 grade.
Note:
After setting the transparency of the [subwindow], please pay
attention to the color of the two windows. After two different colors
adding together, the color displayed will deviate from the previous
one.
3.4.2 Adding program materials

Move the mouse to the top of [Subwindow] and press the right key to
select [Add], the screen will be illustrated as follows:
112
Each subwindow includes materials with different formats and insert
file, flash, MS Excel, MS Word file, Real media player, multimedia,
simple table, editable text, analog clock, video input, digital clock,
picture, temperature and humidity display, text etc. can be selected.
Note:
[Insert file] is file which can add materials with any type.
3.4.3 Introduction of the material property

Insert file…: When the format of the file is undetermined, press [insert
file] and all the files contained in the system can be put to the edition
frame. Materials with different formats own different properties and we
will give a brief introduction about the properties of the materials with
different formats.
○ Property of Flash material The target material file can

be explored and added by
clicking the button.
Cycle: Whether the cycle playing or not can be set to the Flash playing
113
file.
Automatic: It means whether Flash can carry out interactive and
continuous playing.
Note: the system will carry out zoom to FLASH into the size which
is the same with display screen when playing. If the display screen
is relatively small, the phenomenon that the effect of FLASH is not
very clear will probably occur after zooming and please pay
attention when manufacturing.
○ Property of MS excel material

We has owned 53 kinds of admittance stunts at present, meanwhile, we
will continue adding other stunts. The present stunts are as the
following figure:
Order Stunt Order Stunt name Order Stunt
1 Random 21 Cover from 41 Mosaic 1
the left down （slender）
corner
（vertical）
2 Stillness 22 Cover from 42 Levorotation
the right down 360℃
corner
（vertical）
3 Move up 23 Horizontal 43 Levorotation
Close 180℃
4 Move down 24 Horizontal 44 Levorotation
Open 90℃
5 Move left 25 Vertical 45 Dextrorotation
114
close 360℃
6 Move right 26 Vertical Open 46
Dextrorotation
180℃
7 Move from 27 Close corner1 47
corner 1 Dextrorotation
90℃
8 Move from 28 Close corner 2 48 Chessboard
corner 2
9 Move from 29 Open corner1 49 Random line
corner 3
10 Move from 30 Open corner 2 50 Four sides to
corner 4 center
11 cover up 31 Across 51 center to four
vertical sides
12 Cover down 32 Across 52 Foursides to center
horizontal (cross)
13 Cover from 33 Blind vertical 53 Center to four
left sides (cross)
14 Cover from 34 Blind 54 developing

right horizontal
15 Scan corner1 35 Zoom corner 55
（oblique）
16 Scan corner2 36 Zoom corner 1 56
（oblique）
（oblique）
（oblique）
19 Scan1 corner1 39 Zoom corner 4 59
（vertical）
20 Scan1 corner2 40 Mosaic 60
（vertical）
Note:
All the explanations about the stunts of the software are identical
and our stunts will be added with the upgrade of the software
accordingly.
Admittance time: The time needed to finish the admittance stunt (From
115
the admittance to the perfect chart display and then enter the remaining
time).
Value scope: 0-10,000. Each number represents 0.1 second.
Remaining time: the time span from the perfect chart display to the
admittance and each number is in type of second.
Graphic-taking mode: line priority…if the chart is relatively big,
perfectly display the line direction of the chart (Vertical direction) first
and the display order is as Figure 1.
Row priority… if the chart is relatively big, perfectly display the row
direction of the chart (Horizontal direction) first and the display order is
as Figure 2.
Overall zooming: The complete Excel graphic will be carried out

zooming to the lattice which is the same with the display screen for
playing according to the size of the screen.
Note: When the overall zooming is carried out and if the Excel graphic
is too large while the display screen is relatively small, the black screen
or clobber will be displayed on the display screen after the zooming is
carried out.
○ Property of MS Word material:
The stunt and time of admittance and the remaining time shall be in
consistency with the property of other materials.
Background color: The background color of the character can be
selected.
Color switch: No change, black to white, exchange B-W, reverse
colorcan be selected.
116
Note:
Since the Word font adopts the black color generally while the
defaulted background color of the display screen is also in black,
the phenomenon of black screen playing will be resulted and please
pay attention to the color of your WORD document when selecting.
○ Property of Real media player material:
Mute: Mute mode can be set to the Real media playing file.
Cycle: Whether cycle playing can be set to the Real media playing file.
Mute: Mute mode can be set to the Real media playing file.
Cycle: Whether cycle playing can be set to the Real media playing file.
Note:
1. Please make sure that your computer is able to correctly play
different kinds of media files (Including Real) prior to playing.
2. If there is a hint suggesting installing decoder, please install the
version with decoder of our company.
○ Property of the display material of the sensor
117
○ Property of the multimedia material:
Cycle: Whether cycle playing can be set to the multimedia playing file.
Three display modes: Video, visual effect and non-display.
Seven kinds of visual effect types: Magic, atmosphere, strip and wave,
group music, particle, multi-view and laser beam.
Remote URL: When playing the remote media, it is used to input the IP
address number of the streaming media.
Note:
Please make sure your network is smooth and the network speed is
fast enough when remote URL is carried out, thus, the stop
118
phenomenon will not occur in course of playing.
○ Property of the material of the simple table:
All the function interpretations are identical to [Property of Word

material] and please refer to [Property of MS word material]
○ Property of the material of the editable text:

All the settings are the same with WORD and please refer to [Property
of MS word material]
The shortcut is as the following figure:
119
○ Property of the material of the analog clock:
When you select the material file with analog clock format, a defaulted
clock has been produced in the window area of the screen to modify the
parameters.
Characters on the surface of the clock: Time zone or the characters or
LOGO that the user needs can be input and displayed on the surface of
the clock.
Character font: The font of the characters on the surface of the clock
can be set.
Type of the surface of the clock: they are divided into square,
rectangular, circular and elliptic and the defaulted one is in circular
type.
Color of the time degree: It is the color marked in the time degree on
the surface of the clock and the default one is in white.
Type of the time degree: It is the type marked in the time degree on the
surface of the clock and there is square and circular type. The defaulted
one is in type of square.
Size of the time degree: It is the size marked in the time degree on the
surface of the clock with 0-30, 000 value ranges and the defaulted one
is 3.
Note:
When the size of the clock surpasses that of the lattice of the display
screen, the display of the clock will be abnormal.
Color of the scale mark: It is the color indicated in the scale mark on
the surface of the clock and the defaulted one is in white.
Type of the scale mark: It is the type indicated in the scale mark on the
120
surface of the clock and there is square and circular type. The defaulted
one is in type of circular.
Size of the scale mark: It is the size indicated in the scale mark on the
surface of the clock with 0-30, 000 value ranges and the defaulted one
is 3.
Note:
When the size of the clock surpasses that of the lattice of the display
screen, the display of the clock will be abnormal.
Color of the hour hand: The color of the clock can be selected and the
defaulted one is in red.
Color of the minute hand: The color of the minute hand can be selected
and the defaulted one is in red.
Color of the second hand: The color of the second hand can be selected
and the defaulted one is in red.
Font of the date: The font of the date on the surface of the clock can be
selected.
Format of the date: The format of the date display can be altered.
%y4.%m2.%d2 means four-digit in year, two-digit in month and day.
Among which, the number represents the digit number of the day,
month and year and even is used when modifying.
Font of the week: The font of the week on the surface of the clock can
be selected.
Format of the week: The format of the week display can be altered.
Transparency: The clock is able to remove the background display of
the setting.
Background color: The background color can be set to the clock and the
defaulted one is in grey.
Adjustment of time difference (Second): The value of the seconds can
be adjusted according to the local time.
Adjustment of time difference (Minute): The value of the minutes can
be adjusted according to the local time.
Adjustment of time difference (Hour): The value of the hours can be
adjusted according to the local time.
Adjustment of time difference (Date): The value of the date can be
adjusted according to the local time.
Note:
If there is black color when setting the clock, the display screen will
probably not indicate in spite of the clock.
○ Property of the material of the video input:
121
Video equipment: It is used to display your external video source.
Audio equipment: It is used to display your external audio source.
Input port: When there are several external equipments, different input
ports can be selected.
Channel selection: It is mainly for TV and there more 50 channels to be
selected.
Note:
When the external equipment is used, please make sure it is under
normal work and the correctness of the input and output ports.
○ Property of the material of the digital clock:
Time font: It is used to set the font of the characters to display the time.
122
Transparency: One base map is set to display it. Omission is “No”.
Background color: It can set background color to the clock and the
defaulted one is in grey.
Second adjustment: Value of the day can be altered according to the
local time.
Minute adjustment: Value of the day can be altered according to the
local time.
Hour adjustment: Value of the day can be altered according to the local
time.
Day adjustment: Value of the day can be altered according to the local
time.
Timing mode: It is divided into three timing modes which are clock,
count-down and timing.
Target date: It is used to set the date in course of count-down or timing.
Target time: It is used to set the time in course of count-down or timing.
Note:
If it is in black color when setting the clock, the display screen will
probably not indicate in spite of the clock.
○ Property of the material of the digital clock (New arm):

The application method complies with that of the material property of
the standard “Digital clock” and mainly applied to the DBA-9.0 system
of our company.
○ Property of the material of the pictures:
123
Stunt and time of the entrance and delay time are in consistency with
the property of other materials.
Note: if the color is in accordance with the background color when

setting pictures, the display screen probably falls to display
normally.
○ Property of the material of the website page:
Select the website: Press to output the website which will be

displayed on the display screen. Moreover, the content of the website
page you select will be directly indicated in the display screen. If the
size of the website page is larger than that of the playing window, only
one part can be played and sliding bar will appear on the right and
lower side of the playing window. The whole website page can be
played on an overall basis by moving the sliding bar manually.
Note:
When selecting the website page, please make sure that the
computer network is normal, so is the network when playing the
124
studio files later.
○ Property of the text material
Exit time: It means to admit as required.

Row spacing: It means the spacing between two lines of characters and
the value range is from 0 to 30, 000.
Display area: Display of overall screen, row display, font display, single
row text (roll message) or the signal line text splicing can be selected.
Position: It is only applied to the single line text display and makes the
display in the upper, middle or lower side of the screen.
Edition: Edition can be carried out according to the effect you want and
the setting of other property parameter refers to (3) property of the MS
Word material and (7) property of materials of the single line text.
Note: there is a “Shortcut

hortcut”” button on the upper right side of all the
material properties and it points to the several common settings of
the materials. As for the user who uses it for the first time, we
suggest setting within the shortcut.
3.4.4 Illustrations with example

For example, if one multimedia program needs playing, we select
[Insert file] in the subprogram, an “open” dialogue box will pop out to
allow you search for the target material file. In addition, click the blue
arrow button on the right side of the material within the property bar to
125
look for and change the target material file or right click on the
lower side of the [Subwindow] of the project bar; clicking [Select
material file] can also reach the purpose of adding material files.
Select the material file you intend to play and click [Open]. The
dialogue box of the multimedia playing software will pop out and the
name of the program can be customized within the property bar on the
right side. The material file also can carry out automatic adjustment,
mute, cycle, display mode, visual effect type, visual effect stunt and
remote URL.
Note:
When [Mute] or [Cycle] is selected as [Yes], please set [Automatic
adjustment] as [Yes] as well.
Add program to each subwindow one by one and when clicking

[Editing], the forward move in the pull-down menu will make the
selected subwindow and the content of the program change over the last
subwindow and the content of the program; in the same way, the
backward move changes with the next subwindow and the content of
the program.
Click the playing button in the tool bar after finishing the work above
or press the shortcut key F9, the playing file will appear on the
coordinate place of the desktop which has been set. The content of
different subwindows in the same screen will be played at the same
time, if different subwindows are set under the same position, the
content of the previous subwindow will cover the content of the later
subwindow. The content here is synchronous with that played on the
LED display screen.
The software supports several playing windows to open the program
files, play and edit independently at the same time instead of
influencing other playing windows.
126
3.4.5 Subsequent explanation
One program can include several LED screens and each LED screen
will correspond to one or several control cards which can be under the
playing mode at the same time. One LED screen is composed of several
sets of programs which can set the playing mode and play according to
the selected playing mode. The defaulted one is order playing. There
are several subprograms under one set of program and the subprogram
will be played according to the editing order and the subwindows under
the subprogram will also finish playing according to the order.
Section V How to play VCD/DVD/ CD

VCD/DVD/CD
3.5.1 Direct playing
Click the [Tool] menu on the menu bar and select [Studio DVD, VCD
CD], the disk to be played [G:] and others under the pull-out menu,
or CD]
and then decide according to the different systems (Such as Figure 5-1).
Set the place before studio (Including the left side, top, height and
width), then can be carried out.
127
Such as Figure 5-1
3.5.2 Playing in the program

Click [Program window] and right click, the video in CD\VCD\DVD
can be selected by selecting [Add]
dd]-> insert file. Note: the installation of
the VCD/DVD player must come first before playing VCD/DVD and it
is recommended to install PowerDVD or WinDVD. The specific
operation shall refer to (Figure 5-2).
Figure 5-2
Section VI How to play video input
The external video window is mainly used for the TV signal input of
the TV card and the external VCD/DVD. Note: different settings can be
carried out in the occurrence of the TV card.
3.6.1 New-established program window
Click [Program window] and right click, a new video input program
such as Figure 6-2 is established by selecting [Add]->capture video]
(Such as Figure 6-2).
128
Figure 6-1
Figure 6-2
3.6.2 Setting the input window of the video
Video input equipment: Different video cards can be selected (Note:
several options can be possessed by installing several cards).
Sound input equipment: Video sound can be selected (Note: some TV
card carries out sound playing by means of the sound card).
Video input source: It is used to select the video signal source (Note:
most TV cards own 3 video input sources---cabled TV, Video terminal
and S-Video).
TV channel: It is used to select TV channels (Note: some TV card can
not select the TV channel).
Figure 6-3
129
Section VII how to play slide
3.7.1 Playing
Click [Tool] menu on the menu bar and select [Studio PowerPoint
document] in the pull-out menu (Such as Figure 7-1) and the Figure 7-2
will appear. Select one file to be played and establish their position
(Including top, left side, width and height) and finally click ,
the playing area will be moved to the display area of the big screen
automatically when playing.
In Figure 7-2, [Left side] and [Top] mean that the starting point of the
PPT file you intend to play on LED screen. The default status is to see
the display on the positive side and its starting point can be set on the
very right and left side of the display according to the individual
preference or the actual needs. [Width] and [Height] mean the width
and height of the LED screen you intend to establish and the height
shall be changed the number of the lattice which is the same with your
display screen. If [PCI1] is selected before playing, the number of the
lattice that the playing window and main control bring shall be in
consistency. The system will match the size of the PPT and that of the
display screen automatically.
The display of the former and latter page is switched by means of
the two buttons and the switch display can also

be carried out by keyboard and the keys in the upper, lower, right and
left direction.
Figure 7-1
130
Figure 7-2
Note:
1. In order to avoid the wrong operation, the file path in the file
display frame can not be input by the keyboard and please
press [selection] if it needs changing.
2. If the display screen does not indicate after pressing [Playing],
please make sure that whether your PPT file is in all black or
whether the [Standard and format] of the [A rea option] panel
within [Control panel] and [Area and language option] has
selected [Chinese (China)].
3.7.2 Stopping playing
The PowerPoint file is stopped by clicking button in

(Figure 7-2) under the playing status.
Section VIII How to play subti

subtittle and
notification
Notification management is mainly for the notification of inserting
temporarily during the playing process of the program.
3.8.1 Opening the notification management window
Click [Tool] menu in the main menu bar and select [Caption,
notification] menu in the pull-out menu to click and open the dialogue
box of the notification management (Such as Figure 8-1).
131
Figure 8-1
3.8.2 Setting notification management window

Where the notification is played, the times of the cycle playing, interval
at the left side or the right side, the lower interval, mode (Common and
transparent) stunt, stunt time, remaining time and font etc. can be
established in Figure 8-1.
3.8.3 Playing/stopping notification display

When everything is set, click [playing] button in the Figure 8-1 to play
notification and click [Stop] button to stop playing the notification.
Section IX Management of the sports score

3.9.1 select the sports score
Click [Tool] menu in the main menu bar and select [Sports score]
menu item in the pull-out menu to click and open the dialogue box of
the management of the sports score (As Figure 9-1).
132
Figure 9-1
3.9.2 Setting the management of the sports score
The playi ng of the sports score includes two kinds and they
are time playing and score playi ng as well as overall playi ng.
The window shall be selected first (Such as selecting
).
Setting of the time playing
Timing reset: Reset the time to 00:00;
Timing start: Start timing;
Timing stop: Stop timing;
Note: When the count-down is selected, the operation above will point
to it accordingly;
Timing font: The font property of the time display is set;
Upper interval: The position of the upper edge of the big screen of the
time distance is set.
Right interval: The position of the right edge of the big screen of the
time distance is set;
Setting of the score playing
Host: the score situation of the home team and there are two languages
for display;
Score: the score symbol can be like “:”.
The guest party: The score situation of the home team and there are two
languages for display;
Badge: Display of each picture for the master party and the guest party
can be set;
Lower interval: The position of the lower edge of the big screen of the
time distance is set;
133
Score font: The property of the score display font is set;
Background: The background color is set;
3.9.3 Playing/stopping PE score

Click [Playing all] button in Figure 9-1 to play the time and score
situation after everything is set and click [Playing time] to play the
time display. Click [Playing score] to play the score display and click
[Stop] to stop the display of time and score.
Section X Schedule
Timing playing means the conditional program playing by several
programs setting different times according to the time need of the
clients and the setting mode to one program is as follows:
3.10.1 Opening timing instruction list
Click [Program] in the tree-type structure at the upper left side of the
main interface, as Figure 10-1 and when changing the studio mode as
“timing playing”, the timing can be clicked and
arrow at the right side is established to start the dialogue box of the
timing instruction list, as Figure 10-2.
Firstly, select the timing time, starting time, ending time and effective
week and then add, delete and modify after setting the time.
Add: The time instruction is added.
Delete: The time instruction is deleted.
Modify: The time instruction is modified.
Figure 10-1
134
Figure 10-1
Section XI Network control

Tool of the main interface-> allowing the remote controlling the
machine and open remote control
3.11.1 Management of the remote real-time display screen

If the network control is carried out, the computer which controls the
LED display screen must be set as the remote control server while other
computers set as the client machine. Remote control server can be
controlled by the computers of all the clients within the network while
the client machine is able to control all the remote control servers
within the network. If the remote control beyond the network
(Non-LAN) needs carrying out, the remote control server must dial the
number and surf the internet of the machine instead of the LAN,
otherwise, connection can not be conducted.
○ The machine is allowed to be remote controlled: The software
supports remote control, that means one computer controls the display
screen within one LAN while any other computer makes most of the
software to control the display screen by means of the remote control
function. After two computers connect, the function is equivalent to be
like controlled terminal. There will be an icon of computer appearing
135
on the lower right side of the desktop of the computer after the function
is activated, which is illustrated as the following figure:
○ Starting the remote control: It is used by combing with the former

function. It means that one computer controls the display screen within
one LAN while any other computer makes most of the software to
control the display screen by means of the remote control function.
After two computers connect, the function is equivalent to be like
controlling terminal. The following panel will appear after the function
is activated, which is illustrated as the following figure:
Figure 11-1
Input the IP address of the computer to be controlled in the frame of IP
address and press [Insert] to add it to the address frame at the right side.
The software supports the function of controlling several computers at
the same time. Input the user’s name [LED] and code [db starled] and
dbstarled]
press [Ok]
k]. At this time, the desktop of the computer of your control
terminal will display as the desktop of the controlled terminal. You can
carry out any operation to the computer on the controlled terminal.
Note:
1. Before using the function, please make sure that the
communication between your two sets of computers are normal.
How the two sets of computers carry out network refers to the
related instruction of the operation system or call the customer
service personnel of our company.
2. As a kind of protection, when exiting the procedure, the remote
control function can not be exited. If it intends to exist, please press
the right key on the computer icon at the lower right side of the
desktop to select to exist.
136
Section XII Backstage playing
3.12.1 Starting the backstage playing
The function can be realized under Windows 98/XP system and the
following settings are needed before that: click the right key in the
blank place of the desktop and the setting menu will appear.
Click [Property] and the property menu will appear (Figure 12-2),
click [Set] and the monitor (2) is activated. Select [Expand the content
of Windows to the monitor] under the frame and press [Application]
button, and then confirm. In this way, setting has been finished and the
backstage playing can be realized. At this time, when pressing [Back]
button of <LED studio device> too bar, the playing window will switch
at the front and back stage of the monitor. When the playing window is
switched to the front stage, the display screen will indicate Windows
interface.
Figure 12-2
3.12.2 Canceling the backstage playing
The following reverse settings shall be carried out when the front-stage
playing replaces the backstage playing: right click the blank place in the
desktop and Figure 12-1 will appear and then select [Property], Figure
12-2 will appear. Click [Monitor 2] and remove [√] on the [Expand the
content of Windows to the monitor] and click [Monitor 1]. Press [ok]
and right click the mouse, Figure 12-1 will come out. Select property
and Figure 12-2 will appear and click [Set] following with [senior],
Figure 12-3 will come out. Click [display], Figure 12-4 will come out
and then click red switch in [PDF(F)] bar, the switch will turn green
137
and then click [Ok], Click [Yes], the synchronous display will be
recovered.
Figure 12-3
Figure 12-4
138
Section XIII Multi-screen combination
3.13.1 Entering the synchronization of the multi-screen
combination
Click [Set] menu in the main menu bar and select [Software setting] in
the pull-out menu. Select [Multi-screen combination/synchronization]
in the dialogue box which has popped out, as Figure 13-1. Then click
[Combination/synchronous setting] to come into the synchronous
independent setting of the multi-screen combination, which is
illustrated in Figure 13-2.
When the client has several display screens to display independently
and requires that different display screen indicates different contents
which are able to form a perfect content when using. [Current setting]
shall be combined with. The following figure is the schematic diagram
of controlling eight display screens and the explanation is made as
follows:
The display in the figure belongs to the computer with 1, 280*1, 024
resolution. Each number in the figure means one screen and there are
eight screens altogether. Each screen is 288 point long* 244 point wide,
and needs two HUB. All the screens only need one main control and the
function of eight screens to display the same content or different
contents or the complete one content by using the software is realized.
The procedure is as follows:
○ Procedure 1: Set the point number and cabling mode that the actual
HUB brings in [queue of the receiving card] within [LED setting]setting].
Since eight screens need displaying individually and combing one when
necessary, the number that [queue of the receiving card] needs is 8
with each one corresponding to each screen. The following figure is the
139
queue of the first screen:
The following figure is the queue setting of the eighth screen:
Press [S end all] in the lower right side after finishing setting the queue
of all the screens, which is illustrated as the following figure:
○ Procedure 2: One defaulted program list which is in accordance with

the size of LED screen is newly established after returning to the
playing interface. The size in this example is 288*244 lattice. One LED
screen which complies with the lattice after 8 screens are combined
shall also be established and the size in this example is 1, 152*488
lattice, illustrated as the following figure:
140
○ Procedure 3: The combination scheme needed shall be established
within the screen combination, which is illustrated in the following
figure:
Section XIV Software setting

3.14.1 Opening the setting of the software option
Click [Control] menu in the main menu bar and select [option] in the
pull-out menu, the input dialogue box as Figure 14-1 will appear:
141
The option such as the player starting with computer, loading program
142
list automatically when starting, changing the position of the mouse
when starting, confirming when delete/exit, hint to save when closing
the program list, the position of the mouse, studio from U disk, memory
studio/system log and log reservation can be selected.
Note:
The log file is saved under xmplayer\log catalog of the system with
[*. TXT] format and the software will start automatically when the
software encounters faults: the software will start automatically
when encountering faults and exiting.
Timing restart system: the software is started again in the set time.
Confirm when exiting: the software will appear hint dialogue box
when exiting for each time.
143
Chapter IV Accessory
Section I Setting of the common display card

4.1.1 ATI-AGP/PCI series display card
Press the right key of the mouse in the blank place of the desktop and
click [Property] menu in the shortcut menu which has popped out.
Select [Set] option in the [Display property] dialogue box which has
popped out and click [Senior] button to select [Display] option. There
is a red triangle button which will turn green when being clicked in the
right side of FPD display and then click [Application] button.
Note:
played,, select [Cover] option in the senior property and
If video is played
click [Copy mode option] button, then select [Totally identical] and
click [Application] button.
144
4.1.2 NVDIA series of display cards
Press the right key of the mouse in the blank place of the desktop and
click [Property] menu in the shortcut menu which has popped out.
Select [Set] option in the dialogue box of [Display property] which
has popped out and the property dialogue box will appear:
145
Click [Set] and then click [Senior] button, the senior dialogue box
illustrated as the following figure will appear:
146
The left hand side will appear menu after clicking [GeForce4
[GeForce4…… ] and
the following figure will appear after clicking nView of the menu on
the side of the left hand:
Select to copy in the nView mode and click [Application] button. If

video is to be played, click [Troubleshooting] or [Performance]
property page in the senior property, which is illustrated as the
following figure:
147
The hardware acceleration is established as the basic acceleration or
acceleration without hardware and then click [application] button.
Note:
More specific installation explanation about the display card refers
to the instruction of the display card purchased.
Section II manufacturing of the

communication line
4.2.1 Internationally standard type
I. The twisted-pair wire stripper is adopted to remove about 3cm the
external twisted-pair skin and the twisted-par cable is as Figure I after
finishing peeling.
148
图一
The following work is to carry out line alignment the standard

of which is EIA/TIA T568B standard (As Figure 2). The
followings shall be guaranteed when line alignment is carried
out: 1 and 2 line pair is a twisting while 3 and 6 line pair is a
twisting; so is 4 and 5 as well as 7 and 8; both ends of the
power utilize T568B standard and according to the graphic,
line pair is arranged according to certain color order (1. white
orange, 2, orange, 3, white green, 4, blue, 5, white blue, 6,
green, 7, white brown and 8, brown). Special attention will
paid on that the green battle line must come across the blue
line pair. The most likely mistake to be made here is to put the
white green line and green line together on an adj acent basis,
which will result in series interruption and makes the
transmission efficiency lower.
149
Figure II
After line alignment is carried out, arrange the lines and cut down the
bare twisted-pair by professional scissors and only 15mm length shall
be left, then hinge the line lead and put each line of the twisted-pair into
the pin of RJ45 interface orderly. The line in white orange shall be put
in the first pin and so on.
After determining each line of the twisted-pair has been put correctly,
RJ45 pressing line clamp can be used to connect with RJ45 joint.
RJ45 joint which has been made is as Figure IV:
The pin method of RJ45 joint on the other end is the same and the RJ45
joints on both ends of the connection line after finishing shall be
identical. Finally, the tester shall be used to test. In this way, the
manufacturing of RJ45 is hereby finished.
(Figure Ⅲ)
4.2.2 Special explanation

1. Connection method of the computer with DBA-7.0 or
DBT-QA9.0 (That is the couplet method of two sets of
computers)
A end:
1. White and orange, 2. Orange, 3. White and green, 4. Blue, 5. White
150
and blue, 6. Green, 7. White and brown, 8. Brown).
B end:
1. White and green, 2. Green, 3. White and orange, 4. Blue, 5. White
and blue, 6. Orange, 7. White and brown, 8. Brown ).
2. Connection method of DBT-QT synchronous all series LED control
system (that is the connection method of the computer and information
point)
A end:
B end:
3. The schematic diagram of the common 568B mode is as follows:
(Figure IV)
Note:
1. The control system of DBT-Q2007 is able to transmit 160 meters
(Actual measurement) and in order to guarantee the distance of the
transmission, please purchase the product from the formal
companies when purchasing network line and RJ45.
2. 8 cores of each RJ45 head shall be pressed when pressing the net
wire, thus, the reliability of the transmission is ensured.
151
Chapter V Common problems
Section I Synchronous control system

5.1.1 Interruption of the connection
The specific representation is:
① Unsuccessful parameter sending and [connection interruption] will
be suggested;
② Failure to find the control card;
③ The interface of the software fails to adjust, which means under gray
status. The software [LED control equipment list] has no main control
icon.
Methods used to probably solve problems:
① Pull in and out of USB wire again;
② Change USB wire;
③ The equipment manger checks the equipment connection;
④ The computer is confirmed without virus;
⑤ If it is under internal type, it is probably due to the loose slot or dirty
part of PCI. Please insert again or adopt the rubber to wipe the PCI
interface.
5.1.2 No-signal output

The specific representation is:
The pilot lamp in the net mouth of the control card is not bright.
Methods used to probably solve problems:
1. [XMPLAYER] of our company has not been installed and please
determine to install.
2. Failure to open the FPD of the display card. Right click my
computer on the desktop-> property-> setting-> senior-> display->
FPD.
3. Incorrect resolution mode:
The specific representation is: the screen flashes or under
uncontrollable status.
Troubleshooting method:
Adjust the current resolution of the computer to be in accordance with
that of the control card. The product does not totally support several
non-standard modes such as 1, 152*800. Please contact with the
customer service department of our company in any special
requirements.
Section II Asynchronous control system

152
5.2.1 Failure to start normally
Open the power of the control card; the pilot lamp of the power
<LED8>, <LED5> and <LED1> are bright successively; if the network
is correctly connected, the pilot lamp of the network communication
will be bright. If either <LED1> or <LED5> is not bright, it means
failing to start normally and 1 minute power failure is needed to start
again.
5.2.2 Failure to send the content normally

1. It will be invalid to send the content under the circumstance without
the establishment of the connection and operation can be carried out
after the connection is established.
2. Whether the control card connects the power.
3. Whether the setting of the IP address of the computer is in conflict
with the control card.
4. Try to connect again after closing other procedures.
5. When the inspection above has no problems; the damage of the net
mouth of the control card or incorrect connection of the net wire can be
taken into consideration.
6. Whether the IP address of the computer is correct or not. Please refer
to IP setting.
7. Make sure whether the system status LED1 of the control card and
the pilot lamp are bright; if regular flash occurs, please close the power
for 2 minutes and then repeat the connection procedure above;
8. The network connection is normal but the software fails to detect the
control card. DBA-9.0 is started manually.
9. Colorful screen of the walking wizard, DBA-9.0 is restarted after
power failure for 1 minute and wizard is carried out again.
153

Dbstar Arm9 Manual

Uploaded by

Copyright:

Available Formats

Dbstar Arm9 Manual

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Dbstar Arm9 Manual

Uploaded by

Copyright:

Available Formats

LED Display Control System

March 15, 2010

◆ Enter the control software:

Section II Review of the performance of

The explanation illustrated in the figure is as follows:

◆ The outdoor type main control of DBT-Q2007 sending card is as the

The first dial switch (DIP1) controls

[Transmission net wire] National standard net wire, CAT5E or more

1.2.3 Recognition of the DBT-Q2007 and DBT-Q2009 software

No selecting [MBI5030/MBI5039] means what is adjusted at present is

The net wire cascade order of the value characterization on the

The upper and lower 50-core

1.2.5 Error detection function

◆ The driving chip that supports error detection function

� Connection graphic of the error detection and points for attention

[12 port detection]

[16 port detection] [Selection board of the pass-back data] is

1.3.2 The application of the sensor in DBT-Q2007 synchronous

They are non-humidity sensor head 11111001; humidity sensor head:

1.3.3 Application of the brightness sensor in DBT-QA9.0

They are non-humidity sensor head 11110101; humidity sensor head:

1.3.4 The application of the brightness sensor in DBA-7.0

The connection graphic with DBT-Q2007 synchronous receiving

1.4.2 2009 multifunctional board

[Digital tube] Temperature display of the card and display of the

[Interface of the temperature, humidity and brightness sensor]

[Power control relay] 6 circuit controls the switch of the contactor

○ The connection diagram of the hardware is as the following figure

[Probe of the temperature, humidity and brightness sensor]

II. RJ45 pressing line method of the temperature, humidity and

Click the corresponding power switch button according to the

Click [T imely order]

There controller owns 6 groups of switches that can be used. Click

Section I DBA-9.0 asynchronous control

DBA-9.0 (With net mouth output)

[SW1] This is reset button.

[CON3] Standard audio output

2.1.2 Technical parameters

Function Double color Full color

Transmission Standard network Standard network

2.1.3 Introduction of the application method

(TCP/IP)]], click [Property]

◆ DBA-9.0 parameter setting

The dialogue box of [LED control setting] will appear, illustrated as

Click [Ok]k], DBA-9.0 will restart automatically (Reset) and the

The following figure will appear by click [Ok]

DBA-9.0 parameter setting is hereof finished.

Select [ARM9 special program list]

The software is able to switch the program automatically. Select the

Section II DBA-7.0 asynchronous control

2.2.2 Function characteristic

2.2.3 Software introduction and application explanation

2.2.3.1 Software introduction

File, editor, remote, options and help are included.

New establish: it is used to establish a new LED program list

2.2.3.2 Software application

◆ Click [Base parameters] to carry out the setting of the basic

[OE signal] Is the polarity of OE, [Negative] means OE is low (This is

[Row inverse parameters] Means the direction where the data is