NX700 (H)

VHF DIGITAL TRANSCEIVER
NX-700/700H
SERVICE MANUAL
© 2008-4 PRINTED IN JAPAN
B51-8822-00 (N) 446
Cover
(A01-2194-11)
Key top Panel assy

(K29-9401-03) (A62-1162-03)
Microphone
(T91-0639-35)
CONTENTS
GENERAL.....................................................2 ADJUSTMENT ..........................................44
SYSTEM SET-UP .........................................4 TERMINAL FUNCTION .............................62
REALIGNMENT ...........................................5 PC BOARD
INSTALLATION............................................7 DISPLAY UNIT (X54-3640-10) ...............72
DISASSEMBLY FOR REPAIR ....................14 TX-RX UNIT (X57-7380-XX) (A/2) ........74
CIRCUIT DESCRIPTION ............................17 TX-RX UNIT (X57-7380-XX) (B/2) ........78
COMPONENTS DESCRIPTION.................23 INTERCONNECTION DIAGRAM ..............79
PARTS LIST ...............................................26 SCHEMATIC DIAGRAM ............................80
EXPLODED VIEW ......................................39 BLOCK DIAGRAM .....................................98
PACKING....................................................40 LEVEL DIAGRAM ....................................100
TROUBLE SHOOTING ..............................41 SPECIFICATIONS ...................BACK COVER
This product complies with the RoHS directive for the European market. This product uses Lead Free solder.
NX-700/700H
GENERAL
Document Copyrights PERSONAL SAFETY
Copyright 2008 by Kenwood Corporation. All rights re- The following precautions are recommended for personal
served. safety :
No part of this manual may be reproduced, translated, • DO NOT transmit if someone is within two feet (0.6 me-
distributed, or transmitted in any form or by any means, ter) of the antenna.
electronic, mechanical, photocopying, recording, or other- • DO NOT transmit until all RF connectors are secure and
wise, for any purpose without the prior written permission any open connectors are properly terminated.
of Kenwood. • SHUT OFF this equipment when near electrical blasting
caps or while in an explosive atmosphere.
Disclaimer • All equipment should be properly grounded before pow-
er-up for safe operation.
While every precaution has been taken in the preparation • This equipment should be serviced by only qualified
of this manual, Kenwood assumes no responsibility for er- technicians.
rors or omissions. Neither is any liability assumed for dam-
ages resulting from the use of the information contained
herein. Kenwood reserves the right to make changes to any PRE-INSTALLATION CONSIDERATIONS
products herein at any time for improvement purposes. 1. UNPACKING
Unpack the radio from its shipping container and check
Firmware Copyrights for accessory items. If any item is missing, please contact
KENWOOD immediately.
The title to and ownership of copyrights for firmware
embedded in Kenwood product memories are reserved for
2. LICENSING REQUIREMENTS
Kenwood Corporation. Any modifying, reverse engineer-
Federal regulations require a station license for each
ing, copy, reproducing or disclosing on an Internet website
radio installation (mobile or base) be obtained by the equip-
of the firmware is strictly prohibited without prior written
ment owner. The licensee is responsible for ensuring trans-
consent of Kenwood Corporation. Furthermore, any resell-
mitter power, frequency, and deviation are within the limits
ing, assigning or transferring of the firmware is also strictly
permitted by the station license.
prohibited without embedding the firmware in Kenwood
Transmitter adjustments may be performed only by a
product memories.
licensed technician holding an FCC first, second or general
class commercial radiotelephone operator’s license. There is
NXDN Transceivers:
no license required to install or operate the radio.
The AMBE+2(TM) voice coding technology is embedded
in the firmware under the license of Digital Voice Systems,
Inc. 3. PRE-INSTALLATION CHECKOUT
3-1. Introduction
Each radio is adjusted and tested before shipment. How-
INTRODUCTION ever, it is recommended that receiver and transmitter opera-
SCOPE OF THIS MANUAL tion be checked for proper operation before installation.
This manual is intended for use by experienced techni-
cians familiar with similar types of commercial grade com- 3-2. Testing
munications equipment. It contains all required service The radio should be tested complete with all cabling and
information for the equipment and is current as of this pub- accessories as they will be connected in the final installa-
lication date. Changes which may occur after publication tion. Transmitter frequency, deviation, and power output
are covered by either Service Bulletins or Manual Revisions, should be checked, as should receiver sensitivity, squelch
which are issued as required. operation, and audio output. Signaling equipment operation
should be verified.
ORDERING REPLACEMENT PARTS
4. PLANNING THE INSTALLATION
When ordering replacement parts or equipment informa-
tion, the full part identification number should be included. 4-1. General
This applies to all parts: components, kits, and chassis. If Inspect the vehicle and determine how and where the
the part number is not known, include the chassis or kit radio antenna and accessories will be mounted.
number of which it is a part and a sufficient description of Plan cable runs for protection against pinching or crush-
the required component for proper identification. ing wiring, and radio installation to prevent overheating.
2
NX-700/700H
GENERAL
4-2. Antenna SERVICE
The favored location for an antenna is in the center of a
This radio is designed for easy servicing. Refer to the
large, flat conductive area, usually at the roof center. The
schematic diagrams, printed circuit board views, and align-
trunk lid is preferred, bond the trunk lid and vehicle chassis
ment procedures contained in this manual.
using ground straps to ensure the lid is at chassis ground.
4-3. Radio NOTE

The universal mount bracket allows the radio to be • If you do not intend to use the speaker 3.5-mm jack and
mounted in a variety of ways. Be sure the mounting surface the D-sub 25-pin connector, fit the supplied speaker-jack
is adequate to support the radio’s weight. Allow sufficient cap and D-sub cap to stop dust and sand from getting in.
space around the radio for air cooling. Position the radio • If the transceiver is turned ON or OFF when the power-
close enough to the vehicle operator to permit easy access on/off status message is enabled, the transceiver sends
to the controls when driving. the status.
4-4. DC Power and wiring

1. This radio may be installed in negative ground electrical
systems only. Reverse polarity will cause the cable fuse
to blow. Check the vehicle ground polarity before instal-
lation to prevent wasted time and effort.
2. Connect the positive power lead directly to the vehicle
battery positive terminal. Connecting the Positive lead
to any other positive voltage source in the vehicle is not Antenna Speaker D-sub
connector jack cap cap
recommended.
3. Connect the ground lead directly to the battery negative
terminal. Ignition
sense cable
4. The cable provided with the radio is sufficient to handle
the maximum radio current demand. If the cable must be
extended, be sure the additional wire is sufficient for the Power input
current to be carried and length of the added lead. connector
5. INSTALLATION PLANNING – CONTROL STATIONS

5-1. Antenna system
Control station. The antenna system selection depends
on many factors and is beyond the scope of this manual.
Your KENWOOD dealer can help you select an antenna sys-
tem that will best serve your particular needs.
5-2. Radio location

Select a convenient location for your control station ra-
dio which is as close as practical to the antenna cable entry
point. Secondly, use your system’s power supply (which
supplies the voltage and current required for your system).
Make sure sufficient air can flow around the radio and pow-
er supply to allow adequate cooling.
3
NX-700/700H
SYSTEM SET-UP
Merchandise received
License and frequency allocated by FCC Frequency range RF power Type

136.0~174.0MHz 30W K
Choose the type of transceiver 136.0~174.0MHz 50W HK
Are you using YES See page 9.

KRK-10
the remote kit?
(Option)
NO

the ignition sense cable? KCT-46
(Option)
NO
See page 5.
Transceiver programming A personal computer (IBM PC or compatible), programming
interface (KPG-46/46A), and programming software (KPG-111D)
are required for programming.
the public address? KAP-2
(Option)
NO

the voice guide & storage VGS-1
unit? (Option)
NO
Are you using YES

the external speaker? KES-3, KES-5 or KES-6 External speaker
(Option)
NO
Are you using YES

the keypad microphone? KMC-32 or KMC-36
(Option)
NO
Supplied microphone
Desk top microphone KMC-9C
Delivery
4
NX-700/700H
REALIGNMENT
1. Modes 5. PC Mode
5-1. Preface
User mode
The transceiver is programmed by using a personal com-
puter, programming interface (KPG-46/46A) and program-
Panel test mode Panel tuning mode ming software (KPG-111D).
The programming software can be used with a PC or
PC mode Data programming mode compatible. Figure 1 shows the setup of a PC for program-
ming.
Firmware PC test mode PC tuning mode PC
programming mode
KPG-46 or KPG-46A or
KPG-46A + KCT-46 +
Clone mode Tuning cable
(E30-3383-05)
Firmware version information
Mode Function
User mode For normal use.
Used by the dealer to check the fundamen-
Panel test mode
tal characteristics.
Panel tuning mode Used by the dealer to tune the audio. KPG-111D
Used for communication between the radio
PC mode
and PC.
Data programming Used to read and write frequency data and PC PC PC
mode other features to and from the radio. D-SUB D-SUB
USB
(25-pin) (9-pin)
Used to check the radio using the PC.
PC test mode KCT-53U
This feature is included in the FPU. KPG-46 KPG-46A
KPG-46A
Used to tune the radio using the PC.
PC tuning mode Transceiver Transceiver Transceiver
This feature is included in the FPU.
Firmware Used when changing the main program of Fig. 1
programming mode the flash memory.
Used to transfer programming data from
Clone mode
one radio to another. 5-2. Connection procedure
Firmware version Used to confirm the internal firmware ver- 1. Connect the transceiver to the computer using the inter-
information sion. face cable and USB adapter (When the interface cable is
KPG-46A, the KCT-53U can be used.).
2. How to Enter Each Mode Notes:

Mode Operation • You must install the KCT-53U driver in the computer to
User mode Power ON
use the USB adapter (KCT-53U).
• When using the USB adapter (KCT-53U) for the first time,
Panel test mode [ ] + Power ON plug the KCT-53U into a USB port on the computer with
PC mode Received commands from PC the computer power ON.
Panel tuning mode [Panel test mode] + [ ]
2. When the POWER switch on, user mode can be entered
Firmware programming mode [ ] + Power ON
immediately. When PC sends command the transceiver
Clone mode [ ] + Power ON enter PC mode, and “PROGRAM” is displayed on the
Firmware version information [ ] + Power ON LCD.
When data transmitting from transceiver, the red LED is
lights.
3. Panel Test Mode When data receiving to transceiver, the green LED is
Setting method refer to ADJUSTMENT. lights.
4. Panel Tuning Mode Note:

The data stored in the computer must match the “Model
Setting method refer to ADJUSTMENT. Name” when it is written into the flash memory.
5
NX-700/700H
REALIGNMENT
5-3. KPG-46/KPG-46A description 6. Press write button in the window. When the transceiver
(PC programming interface cable: Option) starts to receive data, the [LOADING] display lights.
The KPG-46/46A is required to interface the transceiver 7. If writing ends successfully, the checksum is calculated
to the computer. It has a circuit in its D-sub connector and a result is displayed.
(KPG-46: 25-pin, KPG-46A: 9-pin) case that converts the RS- 8. If you want to continue programming other transceivers,
232C logic level to the TTL level. repeat steps 4 to 7.
The KPG-46/46A connects the 8-pin microphone connec-
tor of the transceiver to the RS-232C serial port of the com- Note:
puter. This mode cannot be entered if the Firmware Program-
ming mode is set to Disable in the Programming soft-
5-4. KCT-53U description (USB adapter: Option) ware.
The KCT-53U is a cable which connects the KPG-46A to
a USB port on a computer. 6-4. Function
When using the KCT-53U, install the supplied CD-ROM 1. If you press the [ ] key while “PROGRAM 115200” is
(with driver software) in the computer. The KCT-53U driver displayed, the display changes to “PROGRAM 19200”
runs under Windows 2000 or XP. (The LED blinks green) to indicate that the write speed
is low speed (19200 bps). If you press the [ ] key again
5-5. Programming software KPG-111D description while “PROGRAM 19200” is displayed, the display
The KPG-111D is the programming software for the changes to “PROGRAM 38400” (The LED lights red and
transceiver supplied on a CD-ROM. This software runs un- orange alternatively). If you press the [ ] key again while
der MS-Windows 2000, XP or Vista on an IBM-PC or com- “PROGRAM 38400” is displayed, the display changes
patible machine. to “PROGRAM 57600” (The LED blinks orange). If you
The data can be input to or read from the transceiver and press the [ ] key again while “PROGRAM 57600” is dis-
edited on the screen. The programmed or edited data can played, the display returns to “PROGRAM 115200” (The
be printed out. It is also possible to tune the transceiver. LED lights orange).
2. If you press the [ ] key while “PROGRAM 115200” is
displayed, the checksum is calculated, and a result is dis-
6. Firmware Programming Mode
played. If you press the [ ] key again while the check-
6-1. Preface sum is displayed, “PROGRAM 115200” is redisplayed.
Flash memory is mounted on the transceiver. This al-
lows the transceiver to be upgraded when new features Note:
are released in the future. (For details on how to obtain the Normally, write in the high-speed mode.
firmware, contact Customer Service.)
7. Clone Mode
6-2. Connection procedure
Connect the transceiver to the personal computer (IBM Programming data can be transferred from one radio to
PC or compatible) using the interface cable (KPG-46/46A) another by connecting them via their 8-pin microphone con-
and USB adapter (KCT-53U: when the interface cable is nectors. The operation is as follows (the transmit radio is
KPG-46A, the KCT-53U can be used.). (Connection is the the master and the receive radio is a slave).
same as in the PC Mode.)
The following data cannot be cloned.
Note: • Tuning data
You can only program firmware from the 8-pin micro- • Embedded message with password
phone connector on the front panel. Using the 25-pin logic • ESN (Electronic Serial Number) data
interface on the rear panel will not work.
Notes:
6-3. Programming The following data can be cloned.
1. Start up the firmware programming software (Fpro.exe • Fleet (own)/ID (own) for FleetSync
(ver. 4.0 or later)). The Fpro.exe exists in the KPG-111D • Unit ID (own) for NXDN
installed holder.
2. Set the communications speed (normally, 115200 bps) 1. Turn the master transceiver power ON with the [ ] key
and communications port in the configuration item. held down. If the read authorization password is set to
3. Set the firmware to be updated by File name item. the transceiver, the transceiver displays “CLONE LOCK”
4. Turn the transceiver power ON with the [ ] key held If the password is not set, the transceiver displays
down. Then, the orange LED on the transceiver lights “CLONE MODE”.
and “PROGRAM 115200” is displayed. 2. When you enter the correct password, and “CLONE
5. Check the connection between the transceiver and the MODE” is displayed, the transceiver can be used as the
personal computer, and make sure that the transceiver is cloning master. The following describes how to enter
in the Program mode. the password.
6
NX-700/700H
REALIGNMENT
3. operates in the User mode. The slave can then be oper-
• How to enter the password with the microphone key- ated by the same program as the master.
pad; 7. The other slave can be continuously cloned. When the
If you press a key while “CLONE LOCK” is displayed, [ ] key on the master is pressed while the master dis-
the number that was pressed is displayed on the trans- plays “END”, the master displays “CLONE MODE”.
ceiver. Each press of the key shifts the display in order Carry out the operation in step 4 to 6. Can not be cloned
to the left. When you enter the password and press if the overwrite password is programmed to the slave.
the [ ] key, “CLONE MODE” is displayed if the en-
tered password is correct. If the password is incorrect, Note:
“CLONE LOCK” is redisplayed. Only the same models can be cloned together.
• How to enter the password with the [ ] and [ ] keys;
If the [ ] and [ ] keys is pressed while “CLONE LOCK”
is displayed, number (0 to 9) are displayd flashing. When
you press the [ ] key, the currently selected number
is determined. If you press the [ ] key after enterning
the password in this procedure, “CLONE MODE” is
displayed if the entered password is correct. If the pass-
word is incorrect, “CLONE LOCK” is redisplayed.
4. Power on the slave transceiver.
5. Connect the cloning cable (Part No. E30-3382-05) to the Cloning cable
modular microphone jacks on the master and slave. (E30-3382-05)
6. Press the [ ] key on the master while the master dis- Fig. 2
plays “CLONE MODE” The data of the master is sent to
the slave. While the slave is receiving the data, “PRO-
8. Firmware Version Information
GRAM” is displayed. When cloning of data is completed,
the master displays “END”, and the slave automatically Turn the transceiver ON with the [ ] key held down.
Then, the version is displayed during holding the [ ] key.
INSTALLATION
1. Ignition Sense Cable (KCT-46: Option)
The KCT-46 is an optional cable for enabling the ignition
function. The ignition function lets you turn the power to
the transceiver on and off with the car ignition key.
1-1. Connecting the KCT-46 cable to the transceiver

1. Open the KCT-46 fuse holder and insert a mini blade fuse
(3A). ( q )
2. While holding a clear protective cover, remove the black
cap at the end of the yellow cable (ignition sense cable) @
of the transceiver. ( w )
3. Connect the plug of the KCT-46 to the yellow cable ter- .
minal of the transceiver. ( e )
4. Connect the other end of the KCT-46 to the ignition line F52-0019-05
of the car. ( r )
:
Note: You must setup using the KPG-111D.
;
Ignition line
of the car
Fig. 1
7
NX-700/700H
INSTALLATION
2. Horn Alert/P.A. Relay Unit (KAP-2: Option) 5. Place the relay unit at the position shown in Figure 2-2
and secure it to the chassis with a screw.
The Horn alert (max. 2A drive), Public address and Exter- 6. Remove the cap on the rear of the chassis by pushing it
nal speaker function are enabled by installing the KAP-2 in from the inside with your finger. ( r )
the transceiver. 7. Pass the 6-pin connector of the cable (E37-1113-15)
through the chassis hole ( t ) and insert the bush into
2-1. Installing the KAP-2 unit in the transceiver the chassis hole.
(The kit A is not used in the KAP-2 accessories) 8. Rotate the bush of the cable 90 degrees counterclock-
1. Remove the cabinet, top packing and shielding plate of wise as viewed from the rear of the chassis. ( y )
the transceiver. 9. Insert the 6-pin connector of the cable into the connector
2. Set the KAP-2 relay unit jumper pins according to the (CN2) of the KAP-2 relay unit. ( u )
purpose of use.
3. Remove the 6-pin jumper connector inserted in the TX- Note: You must setup using the KPG-111D.
RX unit (A/2) connector (CN705). ( q )
4. Insert one side of the lead wire with connector
(E37-1114-05) into the relay unit connector (CN3) ( w )
and the other side into the TX-RX unit (A/2) connector
(CN705) ( e ).
E37-1114-05
@
CN3
.
:
CN705 CN705
;
FIg. 2-1 FIg. 2-2 FIg. 2-3
CN2 >
E37-1113-15
FIg. 2-4
8
NX-700/700H
INSTALLATION
3. Control Head Remote Kit (KRK-10: Option) ■ Install the KRK-10 main panel onto the transceiver
4. Insert the flat cable that was removed in step 2 above
The KRK-10 remote kit is used to remotely operate the
into the connector (CN1) of the interface unit (A/2) of the
transceiver.
KRK-10 main panel (A62-1101-11). ( u )
Note: The terminal side of the flat cable must face down
3-1. Installing the KRK-10 kit to the transceiver when inserting the flat cable into the connector.
1. Remove the front panel from the transceiver. 5. Fit the main panel with four tabs onto the front of the
2. Install the KRK-10 main panel onto the transceiver. chassis. ( i )
3. Install the KRK-10 rear panel onto the front panel. Note: When installing the main panel onto the front of
4. Connect the KRK-10 main panel to the rear panel with the chassis, hold down the flat cable with your fingers to
the cable. prevent it from being caught.
■ Remove the front panel from the transceiver KRK-10 main panel
1. Lift the two tabs of the panel on the bottom of the trans-
ceiver with a flat-head screwdriver ( q ) and remove the
CN1
panel from the chassis ( w ). 2
Note: Confirm that the tabs of the speaker hardware fix-
ture and holder is securely fitted in the front panel.
2. Remove the flat cable from the connector (CN901) of the
display unit of the panel. ( e )
3. Fold the black line of the flat cable (in three parts) as
shown in Figure 3-2. ( r, t, y ) >
CN901
Fig. 3-3
.
■ Install the KRK-10 rear panel onto the front panel
6. Insert the flat cable attached to the interface unit (A/2) of
the KRK-10 rear panel (A82-0056-21) into the connector
(CN901) of the display unit of the panel ( o ). (The flat
cable has been pre-inserted in the connector (CN2) of
@
the rear panel at the time of shipping.)
Note: The terminal side of the flat cable must face down
when inserting the flat cable into the connector.
: 7. Fit the four tabs of the rear panel into the front panel. ( !0 )
CN901
8
Fig. 3-1
Chassis CN2 KRK-10 rear panel
side ;
B =
; B

=
Panel
side
Fig. 3-4
Fig. 3-2
9
NX-700/700H
INSTALLATION
■ Connect the KRK-10 main panel to the rear 10.Install the molded cover ( !3 ) over the connector on the
panel with the cable main panel and secure it with two screws ( !4 ).
8. Insert one 14-pin connector of the cable (E30-7514-15) 11.Insert the other 14-pin connector of the cable into the
into the connector (CN3) of the interface unit (A/2) of the connector (CN4) of the interface unit (B/2) of the rear
main panel. ( !1 ) panel. ( !5 )
Note: Insert the connector that has a sticker onto the 12.Secure the cable bush on the rear panel and fit the wa-
cable to the connector of the main panel. terproof packing (orange) ( !6 ) securely over top.
9. Secure the cable bush on the main panel and fit the wa- 13.Install the molded cover ( !7 ) over the connector on the
terproof packing (orange) ( !2 ) securely over top. rear panel and secure it with two screws ( !8 ).
CN4 Note: A cable can be connected from the left side as shown
in the Figure 3-5 or from right side.
However, the 14-pin connector must be connected to cor-

rect direction.

Sticker
KRK-10
rear panel CN3

KRK-10
main panel

Sticker

(Right side)
Fig. 3-5
4. Voice Guide & Storage Unit

(VGS-1: Option)
4-1. Installing the VGS-1 unit in the transceiver
1. Remove the cabinet, top packing and shielding plate of
the transceiver.
2. Attach two cushions to VGS-1 as shown in Figure 4. ( q )
Note: Be sure not to cover the connector with the bot-
tom cushion.
3. Insert the VGS-1 connector (CN1) into the TX-RX unit (A/2)
connector (CN595). ( w )
Note: You must setup using the KPG-111D. : Cushion

(G13-1994-04)
20 x 30 x 12 mm
VGS-1
CN1
@
Cushion
(G13-1992-04) CN595
21 x 21 x 2.5 mm
Fig. 4
10
NX-700/700H
INSTALLATION
5. External Speaker (Option) ■ Connection Procedure
Insert the crimp terminal into the Square plug supplied
5-1. KES-3 with the KAP-2.
The KES-3 is an external speaker for the 3.5-mm-diameter
speaker jack.
■ Connection Procedure
1. Connect the KES-3 to the 3.5-mm-diameter speaker jack
on the rear of the transceiver.
Black/White 4
lead 5 Square plug
(E59-0419-05)
Black lead
Insulating cover
(F29-0481-15)
Fig. 5-3
Fig. 5-1 ■ KAP-2 Cable (E37-1113-15) 6-pin Connector
5-2. KES-5 or KES-6
Pin No. Color Name
External speaker KES-5 or KES-6 can be installed for 1 2 3
KAP-2. If KES-5 or KES-6 is installed, it can be set by chang- 1 Red HR2
4 5 6
ing the CN1 short pin from pins 4 and 5 to pins 5 and 6 on 2 Blue GND
the KAP-2.
3 Yellow OSP
4 Green ESP
KAP-2 CN1 Connect Set Up
5 Brown GND
4-5 INT. SP or KES-3
6 Black HR1
5-6 KES-5 or KES-6
When you use the KES-5 or KES-6, plug the short pin to
pins 5 and 6 on the KAP-2.
When you use the INT. SP or KES-3, plug the short pin to
pins 4 and 5 on the KAP-2.
KAP-2 unit
HR1
HR2
EXT
INT
1 CN1 6
INT. SP KES-5
or or
KES-3 KES-6
Short pin
Fig. 5-2
11
NX-700/700H
INSTALLATION
6. GPS Receiver Connection 3M Double coated cushion
6-1. Installing the GPS receiver No. 4016 (or No. 4416)
1. Remove the cabinet, top packing and shielding plate of 30 x 25 mm
the transceiver.
2. Remove the front panel from the transceiver.
3. Attach two cushions to the top of the GPS receiver. GPS receiver
4. Attach the GPS receiver to the shield case with two
cushions as shown in Figure 6-2.
5. Solder each lead of the GPS receiver to a necessary loca-
tion of each landing on the component side of the TX-RX
unit (A/2). 3M Double coated cushion
6. Place the GPS antenna cable in the hollow at the rear of No. 4016 (or No. 4416) :
the chassis. (Fig. 6-2 q ) 30 x 25 mm
Note: If the GPS receiver is installed, cut the base of the
convex tab of the top packing with a pair of nippers, or
similar tool. (Fig. 6-3 w )
If the convex tab of the top packing is cut off, the water
proofing property is no longer guaranteed.
TX-RX unit (A/2)

Solder land
OPT10
OPT11
AGND
26P_RD
26P_TD
TXD2
RXD2 Fig. 6-2
OPT1
OPT3
OPT4
OPT5
GPS receiver
5V_1
DTI
OPT8
TXO
OPT7
OPT2
OPT9
RXEO
TXI
RXEI
OPT6
@
POW
33V
Fig. 6-3
5V_2
DGND
Fig. 6-1
12
NX-700/700H
INSTALLATION
6-2. Installing the GPS receiver together with the VGS-1
1. Remove the cabinet, top packing and shielding plate of
the transceiver.
2. Remove the front panel from the transceiver.
3. Attach a cushion to the bottom of the VGS-1 as shown in GPS receiver
Figure 6-5.
Note: Be sure not to cover the connector with the cush-
ion.
4. Insert the VGS-1 connector (CN1) into the TX-RX unit (A/2)
connector (CN595).
5. Perform step 3 to 6 of “6-1. Installing the GPS receiver”
described on page 13.
VGS-1
CN1
TX-RX unit (A/2)
Solder land
OPT10
OPT11
AGND
26P_RD CN595
26P_TD
TXD2
RXD2
OPT1
OPT3
OPT4
OPT5
GPS receiver
5V_1
DTI
OPT8 Fig. 6-5
TXO
OPT7
OPT2
OPT9
RXEO
TXI
RXEI
OPT6
POW
33V
5V_2
DGND
Fig. 6-4
13
NX-700/700H
DISASSEMBLY FOR REPAIR
1. Precautions on Disassembly ■ Removing the speaker hardware fixture
(J21-8481-03) and holder (J19-5485-12)
■ TX-RX PCB (TX-RX unit A/2) Disassembly 1. Remove the speaker lead from the holder hook. ( q )
1. Remove all screws and antenna terminals on the TX-RX
2. Remove the speaker connector from the display unit
PCB.
connector (CN902). ( w )
2. Rotate the bush of the power supply cable 90 degrees
3. When removing the speaker hardware fixture, insert a
counterclockwise as viewed from the rear of the chassis
flat-head screwdriver at the position shown in Figure 2-1
( q ) and remove the power supply cable from the chas-
and tilt it in the direction shown by the arrow. ( e )
sis ( w ).
4. To remove the holder, insert a flat-head screwdriver into
3. When the speaker phone jack is pushed up, using your
tab of the holder and tilt it in the direction shown by the
finger, from the rear of the chassis ( e ), the TX-RX PCB
arrow. ( r )
is removed from the chassis.
Note: The TX-RX PCB and D-sub PCB (TX-RX unit B/2)
:
are connected with a flat cable. Remove them carefully.
4. Turn the TX-RX PCB over and remove the flat cable from
the connector (CN600). ( r )
5. Remove the TX-RX PCB from the chassis.
:
.
CN902
@ Fig. 2-1
Fig. 1-1
Fig. 1-2
;
;
Fig. 2-2
CN600
Fig. 1-3
14
NX-700/700H
2. Precautions on Reassembly
■ TX-RX PCB (TX-RX unit A/2) Reassembly
1. With the TX-RX PCB turned over, insert the flat cable @
from the D-sub PCB (TX-RX unit B/2) into the connector
(CN600) on the TX-RX PCB.
2. Place the TX-RX PCB at its original position, tilt the TX-RX
PCB and install the chassis as shown in Figure 3.
Fig. 4-1
CN403
Fig. 3
■ FINAL shield case (F10-2489-13) installation

procedure
1. Place the shield case on the final section of the TX-RX
IC715 Black
unit (A/2).
2. The shield case is installed on the positioning boss of
the chassis by pushing down on “PUSH2” (on the shield IC403 Red
case) while pushing “PUSH1” (stamped on two parts on
the shield case) to the right. C401
■ Power supply cable installation procedure Fig. 4-2

1. Pass the power supply cable through the chassis hole ( q )
as shown in Figure 4-1 and insert the bush into the chas- ■ Top packing installation procedure
sis hole. 1. Place the top packing over the shielding plate.
2. Rotate the bush of the power supply cable 90 degrees 2. Fit the convex tab of the top packing into the hollow of
clockwise as viewed from the rear of the chassis. ( w ) the chassis. ( q )
3. Align the ignition sense connector (yellow) of the power 3. Fit the chassis into the groove of the top packing. ( w )
supply cable around the chemical capacitor (C401) and Verify that the top packing is in close contact with the
connect it to the TX-RX unit (A/2) connector (CN403). chassis.
4. Align the + (positive) terminal of the power supply cable @
(red) as shown in Figure 4-2 and fix it to the terminal strip
with a screw.
5. Align the – (negative) terminal of the power supply cable :
(black) as shown in Figure 4-2 and fix it to the terminal
strip with a screw.
Fig. 5
15
NX-700/700H
■ D-sub cap installation procedure
To improve water resistance, fit the D-sub cap into the @
D-sub terminal hardware fixture of the transceiver in the fol- :
lowing order:
1. Fit the left side ( q ) of the D-sub cap into the hardware
fixture.
2. Fit the right side ( w ) of the D-sub cap into the hardware
fixture.
3. Fit the center ( e ) of the D-sub cap into the hardware
fixture. Fig. 7-1
Verify that the D-sub cap is in close contact with the
hardware fixture. Spacer
: Speaker
Speaker holder
@ ;
.
Fig. 7-2 Fig. 7-3
■ Removing the lithium cell (W09-0971-05)

Fig. 6 Insert a screwdriver to groove of one side of the socket
(CN405) and pry the lithium cell up from the socket.
■ Installing the holder (J19-5485-12) and speaker
hardware fixture (J21-8481-03)
1. Insert two tabs of the holder (J19-5485-12) into the hol-
lows in the top of the panel. ( q )
2. Push the two tabs of the holder in on the opposite side
of those in step 1 above and fit them into the hollow in
the bottom of the panel. ( w )
Note: Push in the holder until it snaps in place.
3. Install the speaker holder onto the panel. ( e )
Note: To improve water resistance, fit the panel into the Fig. 8
groove of the holder.
4. Place the speaker into the speaker holder. ■ Installing the lithium cell (W09-0971-05)
Note: The speaker must not ride on the holder rib. Insert a lithium cell into one side of the socket (CN405).
5. Place the spacer on the speaker. Push the lithium cell to insert the lithium cell into the
6. Insert the hardware fixture (J21-8481-03) into the hollow socket.
of the panel as shown in Figure 7-3, then push two parts
of the hardware fixture and fit it into the hollow of the
top of the panel. (Fig. 7-3 r )
Note: Push in the hardware fixture until it snaps in place.
7. Insert the speaker connector into the display unit con-
nector (CN902).
8. Place the speaker lead on the holder hook. Fig. 9
16
NX-700/700H
CIRCUIT DESCRIPTION
1. Overview 2. Frequency Configuration
NX-700/700H is a VHF Mobile transceiver designed to The receiver is a double-conversion super heterodyne
operate in the frequency range of 136 to 174MHz. The unit using first intermediate frequency (IF) of 58.05MHz and
consists of receiver, transmitter, phase-locked loop (PLL) second IF of 450kHz. Incoming signals from the antenna
frequency synthesizer, base band parts, power supply, and are mixed with the local signal from the PLL circuit to pro-
control circuits. duce the first IF of 58.05MHz. This is then mixed with
the 57.6MHz second local oscillator output to produce the
450kHz second IF. The transmit signal frequency is gener-
ated by the PLL VCO, and modulated by the signal from the
DSP. It is then amplified and fed to the antenna.
ANT CF
TX/RX: 136~174MHz 450kHz
1st MIX MCF SP

ANT RF MIX AF
SW AMP IF AMP AMP
Base band Circuit

58.05MHz
19.2MHz x3
VCTCXO
57.6MHz
194.05~ MIC
232.05MHz
PLL MIC
PA TX
VCO AMP
AMP AMP 136~174MHz
Fig. 1 Frequency configuration
3. Receiver System 3-2. First Mixer

The signal from the BPF is heterodyned with the first lo-
3-1. RF circuit cal oscillator signal from the PLL frequency synthesizer cir-
The front-end circuit consists of former BPF (D213, cuit at the first mixer DBM (IC204) to become a 58.05MHz
D216, D217, D218),RF amplifier Q210, and latter BPF (D207, first intermediate frequency (IF) signal.
D208, D209 and D210). The first IF signal is fed through a monolithic crystal filter
The BPF covers frequency ranges 136 to 174MHz. (XF202) to further remove spurious signals.
The latter BPF (D207, D208, D209 and D210) attenuates
the unwanted signals, and sends only the necessary signal
to the first mixer.
–118dBm –120.5dBm –114.5dBm –112.5dBm –104dBm

ANT
D213,D216, RF AMP D207~ 1st MIX DBM IF AMP IF AMP FM SYSTEM IC
D217,D218 Q210 D210 IC204 XF202 Q205 Q204 IC202
BPF BPF MCF
Buff AMP Buff AMP Buff AMP

Q9 Q10 Q208
RX
BPF
VCO
0dBm 0dBm
Fig. 2
17
NX-700/700H
CIRCUIT DESCRIPTION
3-3. IF circuit The second IF signal is passed through the ceramic filter
The first IF signal is passed through a four-pole mono- (CF201, CF202) to reject the adjacent channel signal. The
lithic crystal filter (XF202) to reject adjacent channel signal. filtered second IF signal is amplified by AGC amplifier.
The filtered first IF signal is amplified by the first IF amplifier The signal from AGC amplifier is input to AD converter
(Q204, Q205) and then applied to the lF system IC (IC202). (IC510) through ceramic filter (CF203) and operational ampli-
The IF system IC provides a second mixer, AGC amplifier, fier (IC201 and IC704).
and RSSI (Received Signal Strength Indicator).
The second mixer mixes the first IF signal with the
57.6MHz of second local oscillator output and produces the
second IF signal of 450kHz.
ANT
CF203 IC201
IC202
RF Circuit (Front end) BPF
MIX. AGC
2nd OSC
X1 Q203 BPF
VC
x3 CF201
TCXO
CF202
19.2MHz
IC711
IC704 IC701 IC707 (2/2) IC712 Q710 IC715
MUTE
IC510 SW VOL INT. SP
SW
AF AMP
AMT EXT. SP
DSP INAMT SW
IC502 Q709
Fig. 3
3-4. Audio amplifier circuit 3-5. Squelch Circuit

Audio processing (high-pass filter, low-pass filter, de- It amplifies the demodulated noise signal from IC510
emphasized and so on) at FM mode and decoding at NXDN after filtering through BPF circuit. Then, the amplified signal
mode are processed by DSP. Audio signal from IC510, is converted to DC signal by the detection circuit. The con-
IC502 goes through the amplifier (IC701). The signal then verted signal is fed back to IC510.
goes through mute switch (IC707), amplifier (IC711), and
electronic volume control (IC712).
While busy, INAMT becomes High, turn switch (Q709)
on and Mute switch (Q710) off, and signal is fed to AF Pow-
er Amp (IC715). While Non-busy, INAMT is become Low,
turn switch (Q709) off and Mute switch (Q710) on, then
there is not AF output.
IC705 (2/2) Q702 D703 IC705 (1/2)

FMDET ASQDET
IC202 BPF AMP RECT AMP IC510
IC203 (1/2)
VAGC
AMP
IC203 (2/2)
RSSI
AMP
Fig. 4
18
NX-700/700H
CIRCUIT DESCRIPTION
4. Transmitter System 4-2. Base Band Circuit
The audio signal output from the base band circuit is
4-1. Audio Band Circuit converted to digital data of a sampling frequency of 48kHz.
The signal from the microphone goes through the mute This digital data is sent to the DSP (IC502), and voice signals
switch (Q706), the Mic-Mute signal (MM) becomes Low, of 300Hz or lower and frequencies of 3kHz or higher are
then mute switch (Q706) is turned off. The signal from cut off and an audio range 300Hz to 3kHz is extracted. The
microphone goes through Mic-AGC (Q704, Q705, D704, audio signal is then pre-emphasized in FM mode and syn-
D705), and goes through switch IC (IC708), and amplified by thesized with the signals, such as QT and DQT, as required,
Mic-Amp IC706 (1/2), LPF IC706 (2/2) works as anti-aliasing and is then output from the IC510. In Digital mode, the au-
filter. dio signal is converted to the 4-Level FSK base band signal
If an optional scrambler board is installed, the switch and output from the IC510. The DTMF and MSK base band
(IC708) adjusts the signal path so that the audio signal is in- signals are also generated by the DSP and output by the
put to the scrambler board. IC510.
LPF (IC702) works as smoothing filter. The DAC (IC712)
assigns the base band signal to the VCO and VCTCXO (X1).
At this time, the level output according to the transmit car-
rier is fine-adjusted according to each modulation method.
Optional Scrambler Board
IC502
DSP
D703,D704 IC706 IC706
INT. MIC Q707 Q705,Q706 IC708 (1/2) (1/2)
SW AGC SW AMP LPF IC510
MM SCSW
IC1 X1
LPF LPF AMP IC712 AMP VCTCXO
IC702 IC702 IC709

(2/2) (1/2) (1/2) AMP VCO
IC5 (2/2)
Fig. 5
4-3. Drive and Final amplifier level by detecting the power module output with a diodes
The transmit signal obtained from the TX VCO buffer D107, D108 and D109. Diodes D107, D108 and D109 apply
amplifier Q9, is amplified to approximately +17dBm by the a voltage to DC amplifier IC103 (1/2).
driver amplifiers Q14, Q101 and Q102. IC103 (2/2) compares the APC control voltage (PC) gen-
This amplified signal is passed to the power amplifier erated by microprocessor IC510 and DC amplifier IC101 (1/2,
module (power module) IC102, which consists of a MOS- 2/2) with the detection output voltage from IC103 (1/2) to
FET amplifier and capable of transmission output power. control the Vgg Pin of IC102, and stabilizes transmission out-
put.
4-4. APC circuit The APC circuit is configured to protect over-current of
The Automatic transmission power control (APC) circuit the power module due to fluctuations of the load at the
stabilizers the transmitter output power at a predetermined antenna end and to stabilize transmission output at voltage
and temperature variations.
0dBm +17dBm
*D103: NX-700H only ANT
Buff AMP Drive AMP Drive AMP Drive AMP Final AMP D103*,D104,
Q13 Q14 Q101 Q102 IC102 D105,D215
MOD TX VCO SW ANT Filter
Gate
bias D107 D108 D109
DET DET DET
VCTCXO PC DC DC
MB 19.2MHz MP AMP AMP
IC101 IC103
Fig. 6
19
NX-700/700H
CIRCUIT DESCRIPTION
5. PLL Frequency Synthesizer 5-3. PLL IC (IC3)
PLL IC compares the differences in phases of the VCO
5-1. VCTCXO (X1) oscillation frequency and the VCTCXO reference frequency,
VCTCXO (X1) generates a reference frequency of returns the difference to the VCO CV terminal and realizes
19.2MHz for the PLL frequency synthesizer. This reference the “Phase Locked Loop” for the return control. This allows
frequency is applied to pin 9 of the PLL IC (IC3) and con- the VCO oscillation frequency to accurately match (lock) the
nected to IF circuit as a 2nd local signal through Tripler. The desired frequency.
VCTCXO oscillation frequency is determined by DC voltage When the frequency is controlled by the PLL, the fre-
of VC terminal. The VC voltage is fixed to 1.65V by R1 and quency convergence time increases as the frequency dif-
R2, and supplied to VC terminal through IC1. Modulation ference increases when the set frequency is changed. To
signal is also fed to VC terminal through IC1. supplement this, the MCU is used before control by the PLL
The frequency adjustment is achieved by switching IC to bring the VCO oscillation frequency close to the de-
the ratio of dividing frequency that is not adjusted by the sired frequency. As a result, the VCO CV voltage does not
DC voltage impressed to VC. The resolution of adjusting change and is always stable at approx. 3.0V.
frequency is approximately 8Hz. Because twice the VCO The desired frequency is set for the PLL IC by the MCU
output are input as for the input frequency of PLLIC, the (IC510) through the 3-line “SDO1”, “SCK1”, “PCS_RF” se-
sending and receiving frequency can be adjusted by approxi- rial bus. Whether the PLL IC is locked or not is monitored
mately 4Hz resolution. by the MCU through the “PLD” signal line. If the VCO is
not the desired frequency (unlock), the "PLD" logic is low.
5-2. VCO
There is a RX VCO and a TX VCO. 5-4. Doubler (Q6)
The TX VCO (Q10) generates a transmit carrier and the The doubler (Q6) extracts the twice harmonic component
RX VCO (Q9) generates a 1st local signal. For the VCO os- from the signal from the VCO. This twice harmonic compo-
cillation frequency, the transmit carrier is 136 to 174 MHz nents is then fed into PLL(IC3) through band pass filter.
and the 1st local receive signal is 194.05 to 232.05MHz. Band pass filter is consists of two filter. One is for TX
The VCO oscillation frequency is determined by one sys- (L7, 15, 18) and pass band is 272.0 to 348.0MHz. The other
tem of operation switching terminal “T/R” and two systems is for RX 1st Local (L8, 12, 16) and pass band is 388.1 to
of voltage control terminals “C/V” and “V-assist”. 464.1MHz.
The operation switching terminal, “T/R”, is controlled by
the control line (/T_R) output from the MCU (IC510). When
5-5. Local Switch (D101, D205)
the /T_R logic is low, the VCO outputs the transmit carrier
The connection destination of the signal output from
and when it is high, it outputs a 1st local receive signal.
the buffer amplifier (Q14) is changed with the diode switch
The voltage control terminals, “CV” and “V-assist”, are
(D101) that is controlled by the transmission power supply,
controlled by the PLL IC (IC3) and MCU (IC510) and the
80T, and the diode switch (D205) that is controlled by the
output frequency changes continuously according to the
receive power supply, 50R. If the 80T logic is high, it is con-
applied voltage. For the modulation input terminal, “VCO
nected to a send-side pre-drive (Q101). If the 80T logic is
MOD”, the output frequency changes according to the ap-
low, it is connected to a local amplifier (Q208).
plied voltage. This is used to modulate the VCO output.
“VCO MOD” works only when “/T_R” is low.
Q9,Q10
X1 D7,D8
19.2MHz IC3 D11~D16,D18 Q13 Q14 D101,D205
VC PLL Loop BUFF BUFF T/R
VCO to TX stage
TCXO Filter AMP AMP SW
SDO1
80T
50R
to Local Amplifier
SCK1 CV 50C
/PCS RF
VCO MOD Doubler 50C
IC5
150C Q6
Q1
Ripple
Filter
IC4
ASSIST
L7,L15,L18
BPF (TX)
RF RF
SW SW
BPF (RX)
D5,D6 L8,L12,L16 D19,D20
Fig. 7
20
NX-700/700H
CIRCUIT DESCRIPTION
6. Control Circuit 6-4. Key Detection Circuit
Keys are detected using Key scan circuit in IC911. The
The control circuit consists of MCU (IC510) and its pe-
/KI* and KO* signals that are normally pulled up go low
ripheral circuits. IC510 mainly performs the following;
when any key is pressed.
1) Switching between transmission and reception by PTT
signal input.
6-5. DSP
2) Reading system, zone, frequency, and program data
The DSP circuit consists of a DSP (IC502) and processes
from the memory circuit.
the base band signal. The DSP operates on an external
3) Sending frequency program data to the PLL.
clock of 18.432MHz (the same as the IC510), the I/O sec-
4) Controlling squelch on/off by the DC voltage from the
tion operates at 3.3V and the core section operates at 1.5V.
squelch circuit.
The DSP carries out the following processes:
5) Controlling the audio mute circuit by decode data input.
• 4Level FSK processing
• Analog FM pre-emphasis/de-emphasis
6-1. MCU
• Vocoder processing between audio codec and modula-
The MCU (IC510) is 32bit RISC processor, equipped with
tion/demodulation
peripheral function and ADC/DAC.
• CAI processing, such as error correction encoding
This MCU operates at 18.432MHz clock and 3.3V /1.5V
• QT/DQT encoding/decoding
DC. Controls the flash memory, SRAM, DSP, the receive
• DTMF encoding/decoding
circuit, the transmitter circuit, the control circuit, and the dis-
• MSK encoding/decoding
play circuit and transfers data to or from an external device.
• 2TONE encoding/decoding
• Compressor/expander processing
6-2. Memory Circuit • Voice scrambler processing
Memory circuit consists of the MCU (IC510) and the • Transmit/receive audio filtering processing
SRAM (IC503), the flash memory (IC501). The flash memo- • Microphone amplifier AGC processing
ry has capacity of 32Mbit that contains the transceiver con- • Audio mute processing
trol program for the MCU and stores the data. It also stores • Modulation level processing
the data for transceiver channels and operating parameter
that are written by the FPU. This program can be easily
written from external devices. The SRAM has capacity of 7. Power Supply Circuit
1Mbit that contains work area and data area. +B is connected to Final amplifier and DC/DC converter
IC (IC405). IC405 regulates +B voltage to 5.0V (50M). 50M
■ Flash memory operates whenever +B is supplied. IC402 (33M), IC408 (33A)
Note: The flash memory stores the data that is written and IC409 (15M) are enabled while the 50M are operating.
by the FPU (KPG-111D), tuning data (Deviation, Squelch, 33M and 15M provide the power to MCU, DSP, and
etc.), and firmware program. Flash memory. At this time MCU starts working. Voltage
detector IC (IC401) watches +B voltage. If +B voltage is
■ SRAM (static memory) higher than 8.6V, IC401 (/BINT) outputs High. If the /BINT
Note: The SRAM has temporary data area and work signal is high, Q404 (SB SW) is turned on by SBC signal
area. from MCU. (High: SB=ON, Low: SB=OFF). When the SB
When the power supply is off, it is backed up by an inter- is turned on, IC403 (80C), IC404 (50C), IC406 (33C), IC407
nal secondary lithium battery. Therefore, the save data does (33GPS) and IC410 (150C) start working. Q416 and Q412
not break. are controlled by SBC signal. If the SBC signal becomes
High, Q416 (33A-2) operates and Q412 (50MC SW) are
■ Real-time clock turned on.
The clock function is based on real-time clock IC (IC504). The MCU controls the TXC signal to High during trans-
When the power supply is off, it is backed up by an internal mission to supply power (80T) for transmission circuit. The
secondary lithium battery MCU controls the signals (RXC) to High during reception to
supply power (80R, 50R) for reception circuit.
6-3. Display Unit When the MCU detects the PSW (Power switch) signal,
The display unit is composed of the MCU (IC911) and IGN (Ignition sense) signal or /BINT signal, it controls the
the memory IC (IC913), and the LCD & Key backlight etc. SBC signal to Low, and turns the transceiver power (SB) off.
The LCD Ass’y (with LCD Driver) is controlled using the When D401 and Q401 detect over-voltage condition, they
bus lines on the connector (CN905) of the display unit. It turns Q404 (SB SW) off. But the MCU still works.
corrects the LCD contrast voltage using IC909. If +B is not provided to the transceiver, the power is pro-
vided to SRAM and RTC through the secondary battery con-
nected with CN405.
21
NX-700/700H
CIRCUIT DESCRIPTION
+B +B
Final Amp
F401
Q404 SB Audio Amp, Display Block
SB SW PA connector
5A F501
SB
D_Sub 25Pin connector
2A
SBC
IC403 80C Internal Option
AVR Display Block
D401 Q401 Q407 80T
/OVRB TX circuit
DET INV 80T SW
IC405 Q412 50MC TXC

RS-232C Driver
DC/DC 50MC SW 80R
Q408
RX circuit
80R SW
IC408 33A RXC

ASIC (Analog)
AVR 150C
IC410
Assist, Tune circuit
DC/DC
Q416 33A-2
Audio circuit
SW 50C
IC404 VCO, Internal Option,
SBC AVR I/O expander, FM IC
IC409 15M
ASIC, DSP core
AVR
Q409 50R
IC402 33M ASIC, DSP I/O RX circuit
50R SW
AVR Flash memory
33BU RXC
IC401 Q411
/BINT SRAM, RTC
DET 33BU SW IC406 33C
CN405 TCXO, PLL
AVR
IC407 33GPS
Internal Option
AVR
IC506
MCU Reset
DET
Fig. 8
8. Signaling Circuit 9. Compander Circuit

8-1. Encode (QT/DQT/DTMF/MSK/2TONE) The term “compander” means compressor and expand-
Each signaling data signal of QT, DQT, DTMF and MSK is er. The compander reduces noise by utilizing a compressor
generated by the DSP circuit, superposed on a modulation and an expander. The NX-700/700H contains DSP (IC502) to
signal and output from IC510. The modulation balance of perform this operation. The NX-700/700H compander can
the QT/DQT signal is adjusted by the D/A converter (IC712) be turned on or off using the FPU.
and the resulting signal is routed to the modulation input of
the VCO and VCTCXO (X1). The each deviation of the TX
QT, DQT, DTMF and MSK tone is adjusted by changing the
output level of the IC510 and the resulting signal is routed
to VCO and VCXO. The RX DTMF tone is routed to the re-
ceive audio signal system, and is output from the speaker.
8-2. Decode (QT/DQT/DTMF/2TONE/MSK)

The audio signal is removed from the FM detection
signal sent to the DSP circuit and the resulting signal is de-
coded.
22
NX-700/700H
COMPONENTS DESCRIPTION
Display unit (X54-3640-10) TX-RX unit (X57-7380-XX)
Ref. No. Part Name Description Ref. No. Part Name Description
IC901 MOS-IC AFO/BLC SW IC1 MOS-IC Buffer AMP (TCXO modulation)
IC902 MOS-IC AF Buffer AMP (AFO) IC2 MOS-IC Temp Sensor
IC903 MOS-IC Voltage Regulator (5C) IC3 MOS-IC PLL IC
IC904 MOS-IC Voltage Regulator (33C) IC4 MOS-IC Buffer AMP (VCO tune)
IC905 MOS-IC Bus Buffer (TXD0) IC5 MOS-IC VCO Modulation/Buffer AMP (CV)
IC906 MOS-IC DC/DC Converter (N100C) IC101 MOS-IC Auto Power Control
IC907 MOS-IC Dual Bus Buffer (RXD0/RXD1) IC102 MOS-IC Final AMP (RF Power Module)
IC908 MOS-IC AND Gate (TXD1/RXD0) IC103 MOS-IC Auto Power Control
IC909 MOS-IC Buffer AMP (LCD Contrast ADJ) IC201 MOS-IC Buffer AMP (2nd IF DET)
IC910 MOS-IC Bus Buffer (D0-D7) IC202 Analogue IC IF IC
IC911 MOS IC MCU IC203 MOS-IC Buffer AMP (RSSI/VAGC)
IC912 MOS-IC Bus Buffer (A1-A2) IC204 MOS-IC 1st Mixer
IC913 ROM IC Flash ROM IC205,206 MOS-IC Buffer AMP (BPF tune)
Q901 FET AFO SW IC401 MOS-IC Voltage Detector (BINT)
Q902 Transistor HK/RXD0 SW IC402 MOS-IC Voltage Regulator (33M)
Q904 Transistor HK/RXD0 SW IC403 MOS-IC Voltage Regulator (80C)
Q905 Transistor TX/RX LED (TX) IC404 MOS-IC Voltage Regulator (50C)
Q906 Transistor TX/RX LED (BUSY) IC405 Analogue IC DC/DC Converter (50M)
Q908 Transistor LCD Back Light SW IC406 BI-POLAR IC Voltage Regulator (33C)
Q909 Transistor DIMER SW (LCD Back Light) IC407 MOS-IC Voltage Regulator (33GPS)
Q910 Transistor LCD BACK LIGHT SW IC408 MOS-IC Voltage Regulator (33A)
Q911 FET Dimer SW (LCD Back Light) IC409 MOS-IC Voltage Regulator (15M)
Q913 FET LCD Reset SW IC410 Analogue IC DC/DC Converter (150C)
D901 Varistor Surge Absorption (DM/KVL) IC501 ROM IC Flash ROM
D902 Varistor Surge Absorption (HK/RXD) IC502 MCU DSP (BGA)
D903 Zener Diode Over DC Supply Protection IC503 SRAM IC SRAM (BGA)
D904 Varistor Surge Absorption (BLC/AFO) IC504 MOS-IC RTC
D906 Varistor LINE protection (SB) IC505 MOS-IC Delay
D907 Zener Diode OVER DC Supply Protection IC506 MOS-IC Reset (MCU)
D908 Diode KEY Matrix IC507 MOS-IC Bus Buffer (BFSX2)
Reverse Current Prevention (HK/ IC508 MOS-IC Buffer AMP (18.432MHz)
D910 Diode
RXD)
IC509 MOS-IC Bus Buffer (BER CLK/BER DATA)
D911,912 Diode KEY Matrix
IC510 MOS-IC MCU (BGA)
D913 Diode Line Protection (PTT/TXDO)
IC511 MOS-IC AND (PCS_RF/HD2)
D914 LED TX/RX LED
IC512 MOS-IC Level Shift (AND ITXD1/SCTXD)
D915~926 LED LCD Back Light
IC513 MOS-IC Buffer AMP (TXD2)
D927~936 LED KEY Back Light
IC514 MOS-IC Level Shift (I2CCK/I2CDT)
D937 Diode Level Shift (PRST)
IC515 MOS-IC Level Shift (TXDO/RTSO)
IC516 MOS-IC Level Shift (RXDO/CTSO)
IC517 MOS-IC I/O Expander
23
NX-700/700H
IC518 MOS-IC RS-232C Driver Q402 Transistor DC SW (SB)
IC701 MOS-IC LPF (RXAF) Q403 Transistor DC SW (IGN)
IC702 MOS-IC LPF (MOD) Q404 FET DC SW (SB)
IC703 MOS-IC LPF (APC/DEO) Q405 Transistor DC SW (SCTAM1)
IC704 MOS-IC Buffer AMP (2nd IF DET) Q406 FET DC SW (33BU)
IC705 MOS-IC BRF/Buffer AMP (SQ) Q407 Transistor DC SW (80T)
IC706 MOS-IC LPF/SUM AMP Q408 Transistor DC SW (80R)
IC707 MOS-IC RXAF/RXEI SW Q409 Transistor DC SW (50R)
IC708 MOS-IC AF SW (TXO/TXI) Q410 FET DC SW (50MC)
SUM AMP (AI/TONE/MI1 MI2) / Q411 Transistor DC SW (33BU)
IC709 MOS-IC
(MOD/DI)
Q412 Transistor DC SW (50MC)
IC710 MOS-IC AF SW (AI TONE OPT9/VREF)
Q413 Transistor DC SW (80T)
IC711 MOS-IC SUM AMP (AF) / VREF
Q414 Transistor DC SW (80R)
IC712 MOS-IC DAC
Q415 Transistor DC SW (50R)
IC713 MOS-IC AO SW
Q416 FET DC SW (33A-2)
IC714 MOS-IC AFO Buffer
Q417 FET DC SW
IC715 Analogue IC AF Power AMP
Q501 FET DC SW
Q1 Transistor Ripple Filter
Q701 FET SW (W/N)
Q2 Transistor PLL Fin T/R SW
Q702 Transistor Noise AMP
Q3 FET PLL Fin T/R SW
Q703 FET TONE SW
Q5 Transistor PLL Fin T/R SW
Q704,705 Transistor Limit
Q6 Transistor Buffer AMP (PLL Fin)
Q706 FET Mute (MI1)
Q7 Transistor Ripple Filter
Q707 FET Mute (MI2)
Q9,10 FET VCO
Q708 Transistor OPT10 SW
Q11,12 FET T/R SW (VCO)
Q709 Transistor DC SW
Q13 Transistor Buffer AMP (VCO)
Q710 Transistor AF Mute
Q14 Transistor Buffer AMP (RF)
Q901,902 Transistor DC SW (AUXO1, AUXO2)
Q15 FET Buffer AMP (19.2MHz)
D3 Diode Bypass Diode
Q101 Transistor RF Pre-Drive AMP
D5,6 Diode PLL Fin T/R SW
Q102 Transistor RF Drive AMP
Variable Capaci-
D7,8 Frequency Control
Q104 Transistor DSW tance Diode
Q105 Transistor SW (RF Power H/L) Variable Capaci-

D11~16 Frequency Control
tance Diode
Q106 FET SW (RF Power H/L)
Variable Capaci-
D18 TX Modulation
Q201,202 Transistor SW (W/N) tance Diode
Q203 Transistor 2nd Local buffer AMP (X3) D19,20 Diode PLL Fin T/R SW
Q204,205 Transistor 1st IF AMP D21 Diode 2nd Local SW
Q208 Transistor Buffer AMP (Local) D101 Diode T/R SW
Q209 Transistor Ripple Filter D102 Zener Diode PM Drain Baias Protection
Q210 Transistor LNA D103~105 Diode Antenna Switch (NX-700H)
Q212 Transistor SW (W/N) D104,105 Diode Antenna Switch (NX-700)
Q401 Transistor SW (Over DC Supply Protection) D107~109 Diode Power Det
24
NX-700/700H
D201,202 Diode CF SW (W/N) Reverse Current Prevention (OR
D507 Diode
RXD2)
D205 Diode T/R SW
D508 Diode Line Protection
Variable Capaci-
D207~210 Vari-Cap Tune
tance Diode D509,510 Diode Reverse Current Prevention
Variable Capaci- D511 Diode Line Protection (RXD2)
D213 Vari-Cap Tune
tance Diode
D512 Diode Line Protection (AUXIO9)
D215 Diode Antenna Switch
D702 Diode SQ Voltage Control
Variable Capaci-
D216~218 Vari-Cap Tune D703 Diode Noise Detector (SQ)
tance Diode
D704,705 Diode AF Detector (LIMIT)
D401 Zener Diode Over DC Supply Protection
D706 Zener Diode Line Protection (DI)
D403 Diode Reverse Current Prevention
D707 Zener Diode Line Protection (DEO)
D404 Varistor Surge Absorption
D901 Diode Line Protection (BER CK)
D405 Diode Reverse Protection
D902 Diode Line Protection (BER DT)
D406 Diode Reverse Current Prevention (BLVL)
D407 Diode DC/DC Converter (50M)
Reverse Current Prevention (OR
D408 Diode
33M/SBC_2) D905,906 Zener Diode Over DC Supply Protection
D409 Diode DC/DC Converter (50M) D907 Diode Line Protection (AUXIO3)
Reverse Current Prevention (Buck D908 Diode Line Protection (AUXIO4)
D410 Diode
UP Battery)
D909 Diode Reverse Current Prevention (SB)
Reverse Current Prevention
D411 Diode D910 Zener Diode Over DC Supply Protection
(33BU)
D412 Diode Discharge (33A, 33M, CE) D911 Diode Line Protection (AUXIO8)
D501,502 Diode Line Protection D912 Diode Line Protection (AUXIO5)
Reverse Current Prevention (PCS_ D913 Diode Reverse Current Prevention (SB)
D503 Diode
RF) D914 Zener Diode Over DC Supply Protection
D504 Diode Reverse Current Prevention (RXD)
Reverse Current Prevention (OR
D506 Diode
G_RXD2)
25
NX-700/700H
PARTS LIST
CAPACITORS
CC 45 TH 1H 220 J • Capacitor value
CC45
1 2 3 4 5 6 Color* 010 = 1pF 2 2 0 = 22pF
1 = Type ... ceramic, electrolytic, etc. 4 = Voltage rating 100 = 10pF
2 = Shape ... round, square, etc. 5 = Value 101 = 100pF Multiplier
3 = Temp. coefficient 6 = Tolerance 102 = 1000pF = 0.001μF 2nd number
103 = 0.01μF 1st number
• Temperature coefficient
1st Word C L P R S T U 2nd Word G H J K L
Color* Black Red Orange Yellow Green Blue Violet ppm/°C ±30 ±60 ±120 ±250 ±500
ppm/°C 0 –80 –150 –220 –330 –470 –750 Example : CC45TH = –470±60ppm/°C
• Tolerance (More than 10pF) (Less than 10pF)

Code C D G J K M X Z P No code Code B C D F G
(%) ±0.25 ±0.5 ±2 ±5 ±10 ±20 +40 +80 +100 More than 10μF : –10~+50 (pF) ±0.1 ±0.25 ±0.5 ±1 ±2
–20 –20 –0 Less than 4.7μF : –10~+75
• Voltage rating
2nd word A B C D E F G H J K V
1st word
0 1.0 1.25 1.6 2.0 2.5 3.15 4.0 5.0 6.3 8.0 –
1 10 12.5 16 20 25 31.5 40 50 63 80 35
2 100 125 160 200 250 315 400 500 630 800 –
3 1000 1250 1600 2000 2500 2150 4000 5000 6300 8000 –
• Chip capacitors
(EX) C C 7 3 F SL 1H 000 J Refer to the table above. • Dimension
L
1 2 3 4 5 6 7 1 = Type
T
(Chip) (CH, RH, UJ, SL) 2 = Shape
3 = Dimension
(EX) C K 7 3 F F 1H 000 Z 4 = Temp. coefficient W
1 2 3 4 5 6 7 5 = Voltage rating
(Chip) (B, F) 6 = Value Chip capacitor
7 = Tolerance Code L W T
Empty 5.6±0.5 5.0±0.5 Less than 2.0
A 4.5±0.5 3.2±0.4 Less than 2.0
RESISTORS B 4.5±0.5 2.0±0.3 Less than 2.0
• Chip resistor (Carbon) C 4.5±0.5 1.25±0.2 Less than 1.25
(EX) R D 7 3 E B 2B 000 J D 3.2±0.4 2.5±0.3 Less than 1.5
1 2 3 4 5 6 7 E 3.2±0.2 1.6±0.2 Less than 1.25
(Chip) (B, F) F 2.0±0.3 1.25±0.2 Less than 1.25
G 1.6±0.2 0.8±0.2 Less than 1.0
• Carbon resistor (Normal type) H 1.0±0.05 0.5±0.05 0.5±0.05
(EX) R D 1 4 B B 2C 000 J Chip resistor
1 2 3 4 5 6 7 Code L W T
E 3.2±0.2 1.6±0.2 1.0
1 = Type 5 = Rating wattage F 2.0±0.3 1.25±0.2 1.0
2 = Shape 6 = Value G 1.6±0.2 0.8±0.2 0.5±0.1
3 = Dimension 7 = Tolerance H 1.0±0.05 0.5±0.05 0.35±0.05
4 = Temp. coefficient
• Rating wattage
Code Wattage Code Wattage Code Wattage
1J 1/16W 2C 1/6W 3A 1W
2A 1/10W 2E 1/4W 3D 2W
2B 1/8W 2H 1/2W
26
NX-700/700H
PARTS LIST
✽ New Parts. indicates safety critical components. L : Scandinavia K : USA P : Canada
Parts without Parts No. are not supplied. Y : PX (Far East, Hawaii) T : England E : Europe
Les articles non mentionnes dans le Parts No. ne sont pas fournis. Y : AAFES (Europe) X : Australia M : Other Areas
Teile ohne Parts No. werden nicht geliefert. NX-700 (Y51-5140-10)
NX-700H (Y51-5190-10)
DISPLAY UNIT (X54-3640-10)
Ref. No. New
Address parts Parts No. Description Desti- Ref. No. New
Address parts Parts No. Description Desti-
nation nation
58 3B T07-0757-15 SPEAKER
NX-700/700H
59 1C T91-0639-35 MICROPHONE ACCESSORY
1 1B A01-2194-11 COVER
2 3A A62-1162-03 PANEL ASSY 61 2A W09-0971-05 LITHIUM CELL
4 2A B09-0681-03 CAP (KAP-2)

5 3B B11-1850-04 FILTER (LCD)
6 3B B38-0922-05 LCD ASSY
7 3A B42-7296-04 STICKER (NEXEDGE)
8 1D B62-2000-00 INSTRUCTION MANUAL D914 B30-2304-05 LED (RED/GREEN)
D915-926 B30-2281-05 LED (Y)
10 2B E04-0167-15 RF COAXIAL RECEPTACLE (M) D927-936 B30-2282-05 LED (Y)
11 2B E30-7520-15 DC CORD (PIG TAIL)
12 2C E30-7523-35 DC CORD ASSY ACCESSORY C903 CK73HB1E103K CHIP C 0.010UF K
13 1A E37-1118-05 LEAD WIRE WITH CONNECTOR (SHORT CABLE) C905 CK73HB1A104K CHIP C 0.10UF K
14 3B E37-1124-05 LEAD WIRE WITH CONNECTOR (2P/SP) C906 CK73HB1H222K CHIP C 2200PF K
C907-909 CK73HB1H102K CHIP C 1000PF K
15 2A E37-1378-05 FLAT CABLE (30P/D-SUB) C910-912 CC73HCH1H101J CHIP C 100PF J
16 2A E37-1379-05 FLAT CABLE (30P/PANEL)
C913 CK73HB1A104K CHIP C 0.10UF K
18 2B F10-2488-12 SHIELDING PLATE (CHASSIS) C914 CK73HB1H102K CHIP C 1000PF K
19 1A F10-2489-13 SHIELDING CASE (FINAL) C915 CK73FB1E475K CHIP C 4.7UF K
20 1A F10-2490-13 SHIELDING CASE (VCO) C916 CK73GB1E105K CHIP C 1.0UF K
21 2C F52-0024-05 FUSE (BLADE TYPE) 15A/32V C917,918 CK73HB1A104K CHIP C 0.10UF K
- G10-1322-04 FIBROUS SHEET (PANEL-SP) C919 CK73HB1H102K CHIP C 1000PF K

24 3B G10-1342-04 FIBROUS SHEET (BIRITUKI) C920 CC73HCH1H121J CHIP C 120PF J
- G11-4336-04 SHEET (PANEL-FG) C921 CK73HB1A104K CHIP C 0.10UF K
26 1B G11-4343-04 SHEET (STEP) C922-925 CK73HB1H102K CHIP C 1000PF K
27 1A G13-2018-04 CUSHION (FINAL) C926-929 CK73HB1A104K CHIP C 0.10UF K
28 2B G13-2047-04 CUSHION (DC SCREW) C930 CK73GB1E105K CHIP C 1.0UF K

29 2B ✽ G13-2262-04 CUSHION (PLATE-FFC) C931,932 CK73HB1H102K CHIP C 1000PF K
30 1B G53-1613-11 PACKING (SHIELD PLATE) C933 CK73GB1E105K CHIP C 1.0UF K
31 1A G53-1616-03 PACKING (PHINE JACK) C934 CK73HB1H102K CHIP C 1000PF K
32 2B G53-1626-03 PACKING (D-SUB OUTER) C935 CS77BA1E4R7M CHIP TNTL 4.7UF 25WV
33 2B G53-1643-04 PACKING (DC CORD) C936 CC73HCH1H100D CHIP C 10PF D

34 2A G53-1645-03 PACKING (D-SUB INNER) C938 CC73HCH1H100D CHIP C 10PF D
35 2A G53-1662-04 PACKING (ANT) C939 CK73GB1C104K CHIP C 0.10UF K
36 3A G53-1676-03 PACKING (CHASSIS) C940 CK73FB1A106K CHIP C 10UF K
C941,942 CK73HB1H102K CHIP C 1000PF K
38 3C ✽ H02-0630-03 INNER CARTON CASE
39 2D ✽ H12-4235-05 PACKING FIXTURE C943,944 CS77BA1E4R7M CHIP TNTL 4.7UF 25WV
40 2D ✽ H12-4236-05 PACKING FIXTURE C945 CK73GB1H103K CHIP C 0.010UF K
41 3D ✽ H52-2195-02 ITEM CARTON CASE K C946 CC73HCH1H101J CHIP C 100PF J
41 3D ✽ H52-2196-02 ITEM CARTON CASE HK C947 CK73HB1A104K CHIP C 0.10UF K
C948 CC73HCH1H101J CHIP C 100PF J
44 2C J19-1584-15 MIC HOLDER ACCESSORY
45 3B J19-5464-13 HOLDER (SP) C949-954 CK73GB1E105K CHIP C 1.0UF K
46 3B J19-5485-12 HOLDER (PANEL) C955 CC73HCH1H101J CHIP C 100PF J
47 3B J19-5502-03 HOLDER (LCD) C956,957 CK73HB1E103K CHIP C 0.010UF K
48 2B J21-8479-02 MOUNTING HARDWARE (D-SUB) C958 CK73HB1H102K CHIP C 1000PF K
C959,960 CK73HB1E103K CHIP C 0.010UF K
49 3B J21-8481-03 MOUNTING HARDWARE (SP)
50 3B J21-8569-03 MOUNTING HARDWARE (LCD) C961 CK73HB0J105K CHIP C 1.0UF K
51 2C J29-0726-03 BRACKET ACCESSORY C962 CK73HB1A104K CHIP C 0.10UF K
52 3B J30-1289-04 SPACER (SP SHEET) C963 CC73HCH1H101J CHIP C 100PF J
C964 CK73GB1E105K CHIP C 1.0UF K
54 3A K29-9401-03 KEY TOP C965 CK73HB1A104K CHIP C 0.10UF K
A 2B N09-2292-05 HEXAGON HEAD SCREW C966,967 CK73HB1H102K CHIP C 1000PF K

B 1A,2A N67-3008-48 PAN HEAD SEMS SCREW
C 1A,2B N87-2606-43 BRAZIER HEAD TAPTITE SCREW CN901 E40-6559-05 FLAT CABLE CONNECTOR
D 1A,2A,2B N87-2608-48 BRAZIER HEAD TAPTITE SCREW CN902 E41-2671-05 PIN ASSY
56 2C N99-2039-05 SCREW SET ACCESSORY CN905 E40-6557-05 FLAT CABLE CONNECTOR
27
NX-700/700H
PARTS LIST
TX-RX UNIT (X57-7380-XX)
Ref. No. New
nation nation
J901 E58-0522-05 MODULAR JACK R960 RK73HB1J000J CHIP R 0.0 J 1/16W
R962 RK73HB1J000J CHIP R 0.0 J 1/16W
- J31-0551-05 COLLAR R963,964 RK73GB2A391J CHIP R 390 J 1/10W
R965,966 RK73GB2A821J CHIP R 820 J 1/10W
L901,902 L41-1095-39 SMALL FIXED INDUCTOR (1.0UH) R967-974 RK73HB1J103J CHIP R 10K J 1/16W
L903-905 L92-0140-05 CHIP FERRITE
L906 L92-0163-05 BEADS CORE R976 RK73HB1J000J CHIP R 0.0 J 1/16W
L907 L92-0140-05 CHIP FERRITE R977-979 RK73HB1J473J CHIP R 47K J 1/16W
L908 L92-0163-05 BEADS CORE R981,982 RK73HB1J103J CHIP R 10K J 1/16W
R986 RK73HB1J103J CHIP R 10K J 1/16W
X901 L77-1950-05 CRYSTAL RESONATOR (11.0592MHZ) R988 RK73HB1J473J CHIP R 47K J 1/16W
CP907,908 RK75HA1JR00J CHIP-COM 0.00 J 1/16W R989 RK73HB1J474J CHIP R 470K J 1/16W
CP909 RK74HA1J104J CHIP-COM 100K J 1/16W R990 RK73HB1J472J CHIP R 4.7K J 1/16W
CP910 ✽ RK74HA1J101J CHIP-COM 100 J 1/16W R991 RK73HB1J474J CHIP R 470K J 1/16W
CP912 ✽ RK74HA1J101J CHIP-COM 100 J 1/16W R992 RK73HB1J000J CHIP R 0.0 J 1/16W
CP917 RK74HA1J104J CHIP-COM 100K J 1/16W R996 RK73HB1J472J CHIP R 4.7K J 1/16W
R900 RK73HB1J000J CHIP R 0.0 J 1/16W R997 RK73GB2A000J CHIP R 0.0 J 1/10W
R901 RK73GB2A000J CHIP R 0.0 J 1/10W R998 RK73HB1J000J CHIP R 0.0 J 1/16W
R902 RK73HB1J102J CHIP R 1.0K J 1/16W R999 RK73HB1J101J CHIP R 100 J 1/16W
R904 RK73HB1J101J CHIP R 100 J 1/16W
R905 RK73HB1J102J CHIP R 1.0K J 1/16W D901,902 AVRM16080MAAB VARISTOR
D903 02DZ18F-X ZENER DIODE
R906 RK73HB1J331J CHIP R 330 J 1/16W D904 AVRM16080MAAB VARISTOR
R907 RK73HB1J104J CHIP R 100K J 1/16W D906 MINISMDC020F VARISTOR
R908 RK73HB1J473J CHIP R 47K J 1/16W D907 02DZ18F-X ZENER DIODE
R911 RK73HB1J472J CHIP R 4.7K J 1/16W D908 HSC119 DIODE
D910 1SS416 DIODE
R912 RK73HB1J333J CHIP R 33K J 1/16W D911,912 HSC119 DIODE
R913 RK73HB1J823J CHIP R 82K J 1/16W D913 DA204U DIODE
R914 RK73HB1J104J CHIP R 100K J 1/16W D937 1SS416 DIODE
R916,917 RK73HB1J103J CHIP R 10K J 1/16W IC901 TC7W66FK-F MOS-IC
IC902 TC75S51FE(F) MOS-IC
R918 RK73GB2A100J CHIP R 10 J 1/10W IC903 XC6204B502PR MOS-IC
R919 RK73HB1J103J CHIP R 10K J 1/16W IC904 XC6204B332M MOS-IC
R920,921 RK73HB1J101J CHIP R 100 J 1/16W IC905 TC7SH126FU-F MOS-IC
R922-925 RK73HB1J102J CHIP R 1.0K J 1/16W
R926 RK73HB1J103J CHIP R 10K J 1/16W IC906 LM2682MMX MOS-IC
IC907 TC7WH126FU-F MOS-IC
R927 RK73HB1J473J CHIP R 47K J 1/16W IC908 TC7SH08FU-F MOS-IC
R928 RK73HB1J103J CHIP R 10K J 1/16W IC909 LMC7101BIM5 MOS-IC
R929 RK73HB1J474J CHIP R 470K J 1/16W IC910 TC74LCX245FK MOS-IC
R931 RK73FB2B561J CHIP R 560 J 1/8W IC911 30620SPGPU3C MICRO CONTROL UNIT
IC912 TC7WZ245FK-F MOS-IC
R932 RK73FB2B471J CHIP R 470 J 1/8W IC913 29AL16D7KCCA ROM IC
R933 RK73HB1J101J CHIP R 100 J 1/16W Q901 SSM3K15TE(F) FET
R934-937 RK73HB1J473J CHIP R 47K J 1/16W Q902 DTC144EE DIGITAL TRANSISTOR
R938,939 RK73HB1J103J CHIP R 10K J 1/16W
R940 RK73HB1J274J CHIP R 270K J 1/16W Q904 DTC144EE DIGITAL TRANSISTOR
Q905,906 DTC114EE DIGITAL TRANSISTOR
R941 RK73HB1J124J CHIP R 120K J 1/16W Q908,909 DTC114EE DIGITAL TRANSISTOR
R942 RK73HB1J000J CHIP R 0.0 J 1/16W Q910 12A02CH TRANSISTOR
R943 RK73HB1J102J CHIP R 1.0K J 1/16W Q911 SSM3K15TE(F) FET
R945,946 RK73HB1J000J CHIP R 0.0 J 1/16W Q913 UPA672T-A FET
TH901 ERTJ0EV104H THERMISTOR
R949 RK73HB1J102J CHIP R 1.0K J 1/16W
R952 RK73HB1J000J CHIP R 0.0 J 1/16W
TX-RX UNIT (X57-7380-XX for service) -11 : NX-700 -13 : NX-700H
R953 RK73GB2A271J CHIP R 270 J 1/10W C2 CK73HB1H471K CHIP C 470PF K
R954 RK73GB2A470J CHIP R 47 J 1/10W C3 CK73HB1A104K CHIP C 0.10UF K
R955 RK73GB2A271J CHIP R 270 J 1/10W C5 CC73HCH1H101J CHIP C 100PF J
R956 RK73GB2A101J CHIP R 100 J 1/10W C6 CK73HB1E103K CHIP C 0.010UF K
R957,958 RK73GB2A271J CHIP R 270 J 1/10W
28
NX-700/700H
PARTS LIST
Ref. No. New
nation nation
C7 CC73HCH1H470J CHIP C 47PF J C91 CC73HCH1H220J CHIP C 22PF J
C8 CC73HCH1H180J CHIP C 18PF J C92 CK73HB1H102K CHIP C 1000PF K
C9 CK73FB1A106K CHIP C 10UF K C93 CC73HCH1H050B CHIP C 5.0PF B
C12 CK73HB0J105K CHIP C 1.0UF K C95,96 CK73HB1H102K CHIP C 1000PF K
C13 CK73HB1E103K CHIP C 0.010UF K C97 CK73HB1A104K CHIP C 0.10UF K

C14 CC73HCH1H101J CHIP C 100PF J C98 CC73HCH1H100C CHIP C 10PF C
C15,16 CK73HB1E103K CHIP C 0.010UF K C101 CK73HB1H471K CHIP C 470PF K
C18 CK73GB1E105K CHIP C 1.0UF K C103 CK73HB1E103K CHIP C 0.010UF K
C19-23 CC73HCH1H101J CHIP C 100PF J C104-107 CK73HB1H471K CHIP C 470PF K

C24 CK73HB1A104K CHIP C 0.10UF K C108 CK73FB1E475K CHIP C 4.7UF K
C25,26 CC73HCH1H101J CHIP C 100PF J C109 CC73HCH1H330J CHIP C 33PF J
C27 CK73HB1A104K CHIP C 0.10UF K C110-112 CK73HB1H471K CHIP C 470PF K
C28,29 CC73HCH1H101J CHIP C 100PF J C115-117 CK73HB1H471K CHIP C 470PF K

C32 CS77CA1VR15M CHIP TNTL 0.15UF 35WV C119 CK73HB1H471K CHIP C 470PF K
C34 CS77BA1D100M CHIP TNTL 10UF 20WV C121 CC73HCH1H090B CHIP C 9.0PF B
C35 C92-0863-05 CHIP TNTL 0.047UF 35WV C122 CC73HCH1H220J CHIP C 22PF J
C36 CK73HB1H102K CHIP C 1000PF K C123 CC73HCH1H330J CHIP C 33PF J

C37 C93-0787-05 CHIP C 0.1UF K C124 CK73HB1H471K CHIP C 470PF K
C39 CK73HB1H471K CHIP C 470PF K C126 CK73HB1H471K CHIP C 470PF K
C42,43 CC73HCH1H101J CHIP C 100PF J C128 CC73HCH1H330J CHIP C 33PF J

C44,45 CK73HB1H471K CHIP C 470PF K C130 CC73HCH1H101J CHIP C 100PF J
C46 CC73HCH1H470J CHIP C 47PF J C132-134 CK73HB1H471K CHIP C 470PF K
C47 CK73HB0J105K CHIP C 1.0UF K C135 CK73FB1H471K CHIP C 470PF K
C48-51 CK73HB1H471K CHIP C 470PF K C136 CC73HCH1H101J CHIP C 100PF J
C52 CC73HCH1H390G CHIP C 39PF G C137 CC73FCH1H180J CHIP C 18PF J

C53 CC73HCH1H180G CHIP C 18PF G C138 ✽ CK73GB0J335K CHIP C 3.3UF K K
C54 CK73HB0J105K CHIP C 1.0UF K C139 CS77BA1E4R7M CHIP TNTL 4.7UF 25WV HK
C55 CK73HB1A104K CHIP C 0.10UF K C141 CC73HCH1H220J CHIP C 22PF J
C56 CC73HCH1H030B CHIP C 3.0PF B C145 CC73HCH1H470J CHIP C 47PF J
C57 CC73HCH1H020B CHIP C 2.0PF B C148 CC73HCH1H101J CHIP C 100PF J

C61 CC73HCH1H220G CHIP C 22PF G C149 CK73HB1H471K CHIP C 470PF K
C62 CC73HCH1H390G CHIP C 39PF G C151 C92-0875-05 ELECTRO 47UF 25WV
C63 CK73HB1H471K CHIP C 470PF K C154-156 CC73HCH1H101J CHIP C 100PF J
C65,66 CK73HB1H471K CHIP C 470PF K C162 CK73HB1H821K CHIP C 820PF K K

C67 CC73HCH1H330G CHIP C 33PF G C163 CM73F2H090D CHIP C 9.0PF D HK
C68 CK73HB1H102K CHIP C 1000PF K C164 CC73FCH1H180J CHIP C 18PF J
C69 CK73HB1H471K CHIP C 470PF K C165 CM73F2H121J CHIP C 120PF J
C70 CC73HCH1H070B CHIP C 7.0PF B C167 CM73F2H270J CHIP C 27PF J HK
C71 CK73HB1H471K CHIP C 470PF K C167 CM73F2H430J CHIP C 43PF J K

C72 CC73HCH1H100B CHIP C 10PF B C169 CC73GCH1H020B CHIP C 2.0PF B K
C73 CK73HB1H471K CHIP C 470PF K C169 CC73GCH1H060B CHIP C 6.0PF B HK
C75 CK73FB1A106K CHIP C 10UF K C170 CK73HB1H471K CHIP C 470PF K
C76 CC73HCH1HR75B CHIP C 0.75PF B C171 CC73GCH1H0R3B CHIP C 0.3PF B HK
C77,78 CK73HB1H471K CHIP C 470PF K C171 CC73GCH1H0R5B CHIP C 0.5PF B K

C79,80 CC73HCH1H080B CHIP C 8.0PF B C172 CK73HB1H471K CHIP C 470PF K
C81 CC73HCH1H090B CHIP C 9.0PF B C173 CM73F2H220J CHIP C 22PF J HK
C82 CC73HCH1H080B CHIP C 8.0PF B C173 CM73F2H470J CHIP C 47PF J K
C83 CK73GB1E105K CHIP C 1.0UF K C174 CM73F2H180J CHIP C 18PF J HK
C84,85 CK73GB1H103K CHIP C 0.010UF K C175 CK73HB1H471K CHIP C 470PF K

C86 CK73HB1H471K CHIP C 470PF K C176 CC73GCH1H050B CHIP C 5.0PF B HK
C87,88 CC73HCH1H0R5B CHIP C 0.5PF B C176 CC73GCH1H1R5B CHIP C 1.5PF B K
C89 CK73HB1H102K CHIP C 1000PF K C177 CC73GCH1H0R3B CHIP C 0.3PF B HK
C90 CK73HB1H471K CHIP C 470PF K C177 CC73GCH1H0R5B CHIP C 0.5PF B K
29
NX-700/700H
PARTS LIST
Ref. No. New
nation nation
C179 CM73F2H360J CHIP C 36PF J HK C272 CC73HCH1H180G CHIP C 18PF G
C179 CM73F2H390J CHIP C 39PF J K C275 CC73HCH1H270G CHIP C 27PF G
C182 CM73F2H220J CHIP C 22PF J K C276 CK73HB1H471K CHIP C 470PF K
C182 CM73F2H270J CHIP C 27PF J HK C279 CK73HB1H102K CHIP C 1000PF K
C183 CK73HB1H471K CHIP C 470PF K C280 CC73HCH1H180G CHIP C 18PF G

C184 CC73GCH1H030B CHIP C 3.0PF B K C282 CK73HB1H102K CHIP C 1000PF K
C184 CC73GCH1H060B CHIP C 6.0PF B HK C283 CK73HB1H471K CHIP C 470PF K
C186 CC73GCH1H0R3B CHIP C 0.3PF B HK C284 CK73HB1H102K CHIP C 1000PF K
C186 CC73GCH1H0R5B CHIP C 0.5PF B K C285 CC73HCH1H120G CHIP C 12PF G
C188 CM73F2H150J CHIP C 15PF J HK C286 CK73HB1H102K CHIP C 1000PF K

C188 CM73F2H180J CHIP C 18PF J K C287 CC73GCH1H150G CHIP C 15PF G
C190 CK73HB1E103K CHIP C 0.010UF K C288 CK73HB1H102K CHIP C 1000PF K
C193-195 CK73HB1E103K CHIP C 0.010UF K C289 CK73GB1H104K CHIP C 0.10UF K
C198 CK73HB1H471K CHIP C 470PF K C291 CC73HCH1H120G CHIP C 12PF G

C201 CK73HB1E103K CHIP C 0.010UF K C293,294 CK73HB1H102K CHIP C 1000PF K
C202-205 CK73HB1A104K CHIP C 0.10UF K C295 CC73HCH1H120G CHIP C 12PF G
C206 CC73HCH1H100B CHIP C 10PF B C296 CK73HB1H102K CHIP C 1000PF K
C207,208 CK73HB1E103K CHIP C 0.010UF K C297 CC73GCH1H150G CHIP C 15PF G
C210 CC73HCH1H100B CHIP C 10PF B C298 CK73GB1H104K CHIP C 0.10UF K

C212-214 CK73HB1A104K CHIP C 0.10UF K C302 CC73HCH1H120G CHIP C 12PF G
C216 CC73HCH1H680J CHIP C 68PF J C308 CK73HB1A104K CHIP C 0.10UF K

C218 CK73HB1A104K CHIP C 0.10UF K C315 CK73HB1H102K CHIP C 1000PF K
C219,220 CK73GB0J475K CHIP C 4.7UF K C316 CC73GCH1H180G CHIP C 18PF G
C221 CK73FB1A106K CHIP C 10UF K C328 CC73HCH1H270G CHIP C 27PF G
C224 CK73HB1A104K CHIP C 0.10UF K C330-334 CK73HB1A104K CHIP C 0.10UF K

C225 CK73FB1A106K CHIP C 10UF K C335 CC73HCH1H151J CHIP C 150PF J
C226 CC73HCH1H820J CHIP C 82PF J C336 CK73HB1E103K CHIP C 0.010UF K
C227 CK73HB1A104K CHIP C 0.10UF K C337,338 CK73HB1H102K CHIP C 1000PF K
C229 CK73HB1A104K CHIP C 0.10UF K C348 CK73HB1E103K CHIP C 0.010UF K

C230 CK73HB1E103K CHIP C 0.010UF K C351 CK73HB0J105K CHIP C 1.0UF K
C231,232 CK73HB1A104K CHIP C 0.10UF K C352,353 CK73HB1A104K CHIP C 0.10UF K
C233 CK73HB0J105K CHIP C 1.0UF K C354 CK73FB1A106K CHIP C 10UF K

C237 CK73HB1E103K CHIP C 0.010UF K C357 CK73HB1E103K CHIP C 0.010UF K
C242 CK73HB1H471K CHIP C 470PF K C401 C92-0777-05 ELECTRO 1000UF 25WV

C247 CK73HB1A104K CHIP C 0.10UF K C409 CK73HB1E103K CHIP C 0.010UF K
C252 CC73HCH1H010B CHIP C 1.0PF B C410 CK73GB1H103K CHIP C 0.010UF K
C256 CC73HCH1H010B CHIP C 1.0PF B C411 CK73HB1H471K CHIP C 470PF K

C259 CK73HB1E103K CHIP C 0.010UF K C413 CK73GB1E105K CHIP C 1.0UF K
C260,261 CK73HB1H471K CHIP C 470PF K C415 CK73HB1H471K CHIP C 470PF K

C266 CK73HB1H102K CHIP C 1000PF K C421 CK73GB1H473K CHIP C 0.047UF K
C267 CK73HB1H471K CHIP C 470PF K C422 CK73FB1E475K CHIP C 4.7UF K
C268 CK73HB1H102K CHIP C 1000PF K C424 CK73GB1E105K CHIP C 1.0UF K
C269 CC73HCH1H100C CHIP C 10PF C C425 CK73GB1H104K CHIP C 0.10UF K
30
NX-700/700H
PARTS LIST
Ref. No. New
nation nation
C427 CK73HB1H471K CHIP C 470PF K C541 CK73HB1A104K CHIP C 0.10UF K
C428 CC73HCH1H101J CHIP C 100PF J C542 CS77CP0J100M CHIP TNTL 10UF 6.3WV
C429 CK73GB1H104K CHIP C 0.10UF K C543-546 CC73HCH1H101J CHIP C 100PF J
C430,431 CK73FB1E475K CHIP C 4.7UF K C547-550 CK73HB1A104K CHIP C 0.10UF K
C432 C92-0875-05 ELECTRO 47UF 25W C551 CK73HB1E103K CHIP C 0.010UF K

C433 CK73GB1H104K CHIP C 0.10UF K C552 CK73HB0J105K CHIP C 1.0UF K
C435 CK73FB1A106K CHIP C 10UF K C554-558 CK73HB1A104K CHIP C 0.10UF K
C436 CS77BA1A100M CHIP TNTL 10UF 10WV C559 CK73HB1E103K CHIP C 0.010UF K
C437 CK73HB1A224K CHIP C 0.22UF K C560 CK73HB0J105K CHIP C 1.0UF K

C438 CK73FB1A106K CHIP C 10UF K C561-563 CC73HCH1H101J CHIP C 100PF J
C439 CK73HB1E103K CHIP C 0.010UF K C565,566 CC73HCH1H101J CHIP C 100PF J
C440 CK73GB1E105K CHIP C 1.0UF K C567 CK73HB1H102K CHIP C 1000PF K
C441,442 CK73HB1E103K CHIP C 0.010UF K C568-578 CC73HCH1H101J CHIP C 100PF J
C443,444 CK73GB1E105K CHIP C 1.0UF K C579 CK73HB1H102K CHIP C 1000PF K

C445 CK73FB1A106K CHIP C 10UF K C580 CC73HCH1H101J CHIP C 100PF J
C446 C92-0765-05 CHIP TNTL 4.7UF 16WV C581-583 CK73HB1H102K CHIP C 1000PF K
C447 CK73HB1A224K CHIP C 0.22UF K C584,585 CC73HCH1H101J CHIP C 100PF J
C449 CK73GB1C225K CHIP C 2.2UF K C587-589 CK73HB1H102K CHIP C 1000PF K

C450 CK73HB1E103K CHIP C 0.010UF K C590,591 CK73HB1E103K CHIP C 0.010UF K
C451 CK73GB1C225K CHIP C 2.2UF K C592,593 CC73HCH1H101J CHIP C 100PF J
C452 CK73HB0J105K CHIP C 1.0UF K C594,595 CK73HB1E103K CHIP C 0.010UF K
C453 CK73GB1E105K CHIP C 1.0UF K C596 CK73HB1A104K CHIP C 0.10UF K
C454 CK73HB1H471K CHIP C 470PF K C597-607 CK73HB1H102K CHIP C 1000PF K

C455,456 CK73HB1E103K CHIP C 0.010UF K C608 CC73HCH1H101J CHIP C 100PF J
C457,458 CK73GB1E105K CHIP C 1.0UF K C609 CK73HB1H102K CHIP C 1000PF K
C459 C92-0765-05 CHIP TNTL 4.7UF 16WV C610 CC73HCH1H101J CHIP C 100PF J
C460 CK73HB1A104K CHIP C 0.10UF K C611 CK73HB1H102K CHIP C 1000PF K
C461 CC73HCH1H181J CHIP C 180PF J C612 CK73GB1H103K CHIP C 0.010UF K

C462 CK73HB1H471K CHIP C 470PF K C613-616 CK73GB1E105K CHIP C 1.0UF K
C463 CK73HB0J105K CHIP C 1.0UF K C618 CK73HB1E103K CHIP C 0.010UF K
C464 CC73HCH1H220J CHIP C 22PF J C620,621 CK73HB1E103K CHIP C 0.010UF K
C465-467 CK73GB1E105K CHIP C 1.0UF K C701 ✽ CK73GB0J335K CHIP C 3.3UF K

C471 CK73HB0J105K CHIP C 1.0UF K C705 CK73HB1H122K CHIP C 1200PF K
C473 CS77BA1E4R7M CHIP TNTL 4.7UF 25WV C706 CK73HB1H331K CHIP C 330PF K
C475 CK73FB1A106K CHIP C 10UF K C708 CK73HB1H122K CHIP C 1200PF K
C501,502 CK73HB0J105K CHIP C 1.0UF K C709 CC73HCH1H221J CHIP C 220PF J

C503-507 CK73HB1A104K CHIP C 0.10UF K C710 CK73HB1E103K CHIP C 0.010UF K
C511-514 CK73HB1A104K CHIP C 0.10UF K C714 CK73HB1E103K CHIP C 0.010UF K
C515 CK73HB0J105K CHIP C 1.0UF K C715 CK73HB1H122K CHIP C 1200PF K

C516,517 CK73HB1A104K CHIP C 0.10UF K C716 CC73HCH1H221J CHIP C 220PF J
C518 CK73GB1E105K CHIP C 1.0UF K C717 CK73HB1A104K CHIP C 0.10UF K
C520-523 CK73HB1E103K CHIP C 0.010UF K C718 CC73HCH1H221J CHIP C 220PF J
C527 CK73HB1E103K CHIP C 0.010UF K C719,720 CK73HB1A104K CHIP C 0.10UF K

C529,530 CK73HB1E103K CHIP C 0.010UF K C722 CC73HCH1H470J CHIP C 47PF J
C531 CK73HB1A104K CHIP C 0.10UF K C723,724 CK73HB1A104K CHIP C 0.10UF K
C533 CK73HB1A104K CHIP C 0.10UF K C726 CK73HB1A104K CHIP C 0.10UF K

C535 CS77CP0J100M CHIP TNTL 10UF 6.3WV C729 CK73HB1A104K CHIP C 0.10UF K
C537,538 CK73HB1A104K CHIP C 0.10UF K C731 CK73HB1A104K CHIP C 0.10UF K
31
NX-700/700H
PARTS LIST
Ref. No. New
nation nation
C735 CK73FB1E475K CHIP C 4.7UF K
C736 CC73HCH1H101J CHIP C 100PF J CN401,402 E23-1260-04 TERMINAL
C737 CK73HB1A104K CHIP C 0.10UF K CN403 E41-1682-05 PIN ASSY
C738 CK73HB1H102K CHIP C 1000PF K CN502-513 E23-1278-05 TERMINAL
CN516,517 E23-1278-05 TERMINAL
C740 CK73HB1H472K CHIP C 4700PF K CN520 E23-1278-05 TERMINAL
C742 CK73HB1A104K CHIP C 0.10UF K CN527 E23-1278-05 TERMINAL
C743 CK73HB1E103K CHIP C 0.010UF K CN540 E23-1278-05 TERMINAL
C744 CK73HB1A104K CHIP C 0.10UF K CN542,543 E23-1278-05 TERMINAL
CN549 E40-6720-05 SOCKET FOR PIN ASSY
C745-747 CK73HB1E103K CHIP C 0.010UF K CN595 E40-6361-05 PIN ASSY
C748-751 CK73HB1A104K CHIP C 0.10UF K
C752,753 CK73HB1E103K CHIP C 0.010UF K CN597 E40-6558-05 FLAT CABLE CONNECTOR
C754 CK73HB1H102K CHIP C 1000PF K CN600 E40-6560-05 FLAT CABLE CONNECTOR
C757 CC73HCH1H150J CHIP C 15PF J CN611,612 E23-1278-05 TERMINAL
CN614 E23-1278-05 TERMINAL
C761 CK73HB1E103K CHIP C 0.010UF K CN705 E40-6582-05 PIN ASSY
C762,763 CK73HB1A104K CHIP C 0.10UF K
C764 CC73HCH1H220J CHIP C 22PF J CN901 E40-6560-05 FLAT CABLE CONNECTOR
C765,766 CK73GB1E105K CHIP C 1.0UF K J701 E11-0425-05 3.5D PHONE JACK (3P)
C767 CK73HB1A104K CHIP C 0.10UF K J901 E58-0521-05 SUB SOCKET(D)
C768,769 CK73HB1E103K CHIP C 0.010UF K F401 F53-0328-05 FUSE 5A

C770 CK73HB1A104K CHIP C 0.10UF K F501 F53-0352-05 FUSE 2A
C774 CK73HB1H102K CHIP C 1000PF K CN405 J19-5386-05 HOLDER
CD201 L79-1850-05 TUNING COIL
C776 CK73HB0J105K CHIP C 1.0UF K CF201 L72-1017-05 CERAMIC FILTER
C777 CK73HB1H102K CHIP C 1000PF K CF202 L72-1021-05 CERAMIC FILTER
C778 CK73HB1A104K CHIP C 0.10UF K CF203 L72-1020-05 CERAMIC FILTER
C779 CC73HCH1H680J CHIP C 68PF J L1 L41-4795-39 SMALL FIXED INDUCTOR (4.7UH)
C782-786 CK73HB1A104K CHIP C 0.10UF K
L2 L92-0163-05 BEADS CORE
C787 CK73FB1A106K CHIP C 10UF K L3,4 L40-1001-86 SMALL FIXED INDUCTOR (10UH)
C788 CK73HB1A104K CHIP C 0.10UF K L7,8 L40-5667-92 SMALL FIXED INDUCTOR (5.6NH)
C789 CK73FB1E475K CHIP C 4.7UF K L10,11 L40-2285-92 SMALL FIXED INDUCTOR (220NH)
C790 CK73FB1A106K CHIP C 10UF K L12 L40-6875-92 SMALL FIXED INDUCTOR (68NH)
C791 CK73HB1H102K CHIP C 1000PF K
L13,14 L40-2285-92 SMALL FIXED INDUCTOR (220NH)
C792 CC73HCH1H470J CHIP C 47PF J L15 L40-8275-92 SMALL FIXED INDUCTOR (82NH)
C793 CK73HB1H102K CHIP C 1000PF K L16 L40-5667-92 SMALL FIXED INDUCTOR (5.6NH)
C794,795 CK73FB1A106K CHIP C 10UF K L17 L40-2285-92 SMALL FIXED INDUCTOR (220NH)
C796-799 CK73HB1A104K CHIP C 0.10UF K L18 L40-5667-92 SMALL FIXED INDUCTOR (5.6NH)
C801,802 CK73GB1E105K CHIP C 1.0UF K
L19 L40-2285-92 SMALL FIXED INDUCTOR (220NH)
C803-805 CK73HB1H102K CHIP C 1000PF K L20 L40-3975-92 SMALL FIXED INDUCTOR (39NH)
C806 C92-0906-05 ELECTRO 330UF 16WV L22 L34-4610-05 AIR-CORE COIL
C807 C92-0875-05 ELECTRO 47UF 25WV L23 L34-4607-05 AIR-CORE COIL
C809 CK73HB1H102K CHIP C 1000PF K L24 L92-0446-05 BEADS CORE
C810 CK73HB1H471K CHIP C 470PF K
L25,26 L40-3391-86 SMALL FIXED INDUCTOR (3.3UH)
C811 CK73HB1H102K CHIP C 1000PF K L27 L40-1085-71 SMALL FIXED INDUCTOR (100NH)
C813 CK73FB1A106K CHIP C 10UF K L28 L40-1085-92 SMALL FIXED INDUCTOR (100NH)
C814 CK73HB1H471K CHIP C 470PF K L31-36 L92-0163-05 BEADS CORE
C815,816 CK73FB1A106K CHIP C 10UF K L40,41 L92-0163-05 BEADS CORE
C817 CK73HB1E103K CHIP C 0.010UF K
L101 L40-8275-92 SMALL FIXED INDUCTOR (82NH)
C818 CK73HB0J105K CHIP C 1.0UF K L102 L40-6875-92 SMALL FIXED INDUCTOR (68NH)
C820 CK73GB1E105K CHIP C 1.0UF K L103 L92-0140-05 CHIP FERRITE
C825 CC73HCH1H101J CHIP C 100PF J
L106 L92-0140-05 CHIP FERRITE
C901 CC73HCH1H101J CHIP C 100PF J L107-109 L92-0179-05 CHIP FERRITE HK
C902 CK73HB1H102K CHIP C 1000PF K L108,109 L92-0179-05 CHIP FERRITE K
C903-906 CC73HCH1H101J CHIP C 100PF J L110 L34-4638-05 AIR-CORE COIL
C907 CK73HB1H102K CHIP C 1000PF K L111 L34-4744-05 AIR-CORE COIL
C908-921 CC73HCH1H101J CHIP C 100PF J
32
NX-700/700H
PARTS LIST
Ref. No. New
nation nation
L112-115 L34-4742-05 AIR-CORE COIL R30 RK73HB1J000J CHIP R 0.0 J 1/16W
L116 L34-4848-05 AIR-CORE COIL R31 RK73HB1J151J CHIP R 150 J 1/16W
L201 L40-1085-71 SMALL FIXED INDUCTOR (100NH) R33 RK73HB1J184J CHIP R 180K J 1/16W
L202 L40-5681-86 SMALL FIXED INDUCTOR (0.56UH) R34 RK73HB1J473J CHIP R 47K J 1/16W
L204 L41-4778-45 SMALL FIXED INDUCTOR (47NH) R35 RK73HB1J102J CHIP R 1.0K J 1/16W
L205 L40-5681-86 SMALL FIXED INDUCTOR (0.56UH) R36 RK73HH1J391D CHIP R 390 D 1/16W
L206 L92-0138-05 CHIP FERRITE R37 RK73HB1J103J CHIP R 10K J 1/16W
L207 L40-5681-86 SMALL FIXED INDUCTOR (0.56UH) R38 RK73HB1J106J CHIP R 10M J 1/16W
L208 L92-0138-05 CHIP FERRITE R39 RK73HB1J472J CHIP R 4.7K J 1/16W
L209 L39-1498-05 TOROIDAL COIL R42,43 RK73HB1J000J CHIP R 0.0 J 1/16W

L211 L40-1085-92 SMALL FIXED INDUCTOR (100NH) R45,46 RK73HB1J223J CHIP R 22K J 1/16W
L212 L39-1498-05 TOROIDAL COIL R47 RK73HB1J000J CHIP R 0.0 J 1/16W
L214 L39-1498-05 TOROIDAL COIL R49 RK73HB1J123J CHIP R 12K J 1/16W
L217-219 L34-4566-05 AIR-CORE COIL R52 RK73HB1J683J CHIP R 68K J 1/16W
L220 L92-0138-05 CHIP FERRITE R56 RK73HB1J331J CHIP R 330 J 1/16W
L221 L34-4566-05 AIR-CORE COIL R57 RK73HB1J472J CHIP R 4.7K J 1/16W
L229,230 L34-4605-05 AIR-CORE COIL R61 RK73HB1J223J CHIP R 22K J 1/16W
L401-403 L92-0179-05 CHIP FERRITE HK R62 RK73HB1J474J CHIP R 470K J 1/16W
L402,403 L92-0179-05 CHIP FERRITE K R63 RK73HB1J472J CHIP R 4.7K J 1/16W
L404 L92-0639-05 CHIP FERRITE R64,65 RK73HH1J271D CHIP R 270 D 1/16W
L405 L33-1496-05 SMALL FIXED INDUCTOR R66 RK73HB1J121J CHIP R 120 J 1/16W
L406 L33-1462-05 SMALL FIXED INDUCTOR R67 RK73HB1J151J CHIP R 150 J 1/16W
L501-503 L92-0138-05 CHIP FERRITE R68 RK73HB1J102J CHIP R 1.0K J 1/16W
L506-511 L92-0138-05 CHIP FERRITE R69 RK73HB1J473J CHIP R 47K J 1/16W
L517,518 L92-0138-05 CHIP FERRITE R71 RK73HB1J101J CHIP R 100 J 1/16W

L521-523 L92-0162-05 BEADS CORE R72 RK73HB1J332J CHIP R 3.3K J 1/16W
L901,902 L92-0140-05 CHIP FERRITE R73 RK73HB1J103J CHIP R 10K J 1/16W
L903-905 L92-0162-05 BEADS CORE R74 RK73HB1J271J CHIP R 270 J 1/16W
X1 L77-3014-05 TCXO (19.2MHZ) R75 RK73HB1J222J CHIP R 2.2K J 1/16W
X501 L77-1802-05 CRYSTAL RESONATOR (32768HZ) R76 RK73HB1J470J CHIP R 47 J 1/16W

X502 L77-3015-05 TCXO (18.432MHZ) R77 RK73HB1J000J CHIP R 0.0 J 1/16W
XF202 L71-0649-05 MCF (58.05MHZ) R78 RK73HB1J472J CHIP R 4.7K J 1/16W
R79 RK73HB1J560J CHIP R 56 J 1/16W
R1,2 RK73HH1J223D CHIP R 22K D 1/16W R80 RK73HB1J183J CHIP R 18K J 1/16W
R4 RK73HB1J224J CHIP R 220K J 1/16W R82 RK73HB1J102J CHIP R 1.0K J 1/16W
R5 RK73HB1J101J CHIP R 100 J 1/16W R83 RK73GB2A272J CHIP R 2.7K J 1/10W
R6,7 RK73HB1J472J CHIP R 4.7K J 1/16W R84 RK73HB1J221J CHIP R 220 J 1/16W
R10 RK73HB1J000J CHIP R 0.0 J 1/16W
R11,12 RK73HB1J100J CHIP R 10 J 1/16W R88,89 RK73HB1J000J CHIP R 0.0 J 1/16W
R13 RK73HB1J103J CHIP R 10K J 1/16W R90,91 RK73GB2A000J CHIP R 0.0 J 1/10W
R14,15 RK73HB1J100J CHIP R 10 J 1/16W R92,93 RK73HB1J000J CHIP R 0.0 J 1/16W
R17 RK73HB1J000J CHIP R 0.0 J 1/16W R102 RK73HB1J271J CHIP R 270 J 1/16W
R18 RK73HB1J100J CHIP R 10 J 1/16W
R21 RK73HB1J100J CHIP R 10 J 1/16W R104 RK73HB1J271J CHIP R 270 J 1/16W
R22 RK73HB1J473J CHIP R 47K J 1/16W R105 RK73HB1J333J CHIP R 33K J 1/16W
R25 RK73HB1J000J CHIP R 0.0 J 1/16W
R26 RK73HB1J474J CHIP R 470K J 1/16W R108 RK73GB2A101J CHIP R 100 J 1/10W
R27 RK73HB1J104J CHIP R 100K J 1/16W R109 RK73HB1J471J CHIP R 470 J 1/16W
R28 RK73HB1J473J CHIP R 47K J 1/16W R110 RK73GB2A220J CHIP R 22 J 1/10W
33
NX-700/700H
PARTS LIST
Ref. No. New
nation nation
R113 RK73GB2A220J CHIP R 22 J 1/10W R220 RK73HB1J473J CHIP R 47K J 1/16W
R114 RK73HB1J331J CHIP R 330 J 1/16W R221 RK73HB1J183J CHIP R 18K J 1/16W
R115 RK73HB1J473J CHIP R 47K J 1/16W K R222 RK73HB1J222J CHIP R 2.2K J 1/16W
R115 RK73HB1J563J CHIP R 56K J 1/16W HK R223 RK73HB1J274J CHIP R 270K J 1/16W
R116 RK73HB1J223J CHIP R 22K J 1/16W K R225 RK73HB1J153J CHIP R 15K J 1/16W
R117 RK73HB1J000J CHIP R 0.0 J 1/16W R226 RK73HB1J223J CHIP R 22K J 1/16W
R122 RK73HB1J332J CHIP R 3.3K J 1/16W R232 RK73HB1J103J CHIP R 10K J 1/16W
R123 RK73FB2B221J CHIP R 220 J 1/8W HK R234 RK73HB1J221J CHIP R 220 J 1/16W
R123 RK73FB2B271J CHIP R 270 J 1/8W K R235 RK73HB1J101J CHIP R 100 J 1/16W
R124,125 RK73FB2B390J CHIP R 39 J 1/8W K R236 RK73HB1J104J CHIP R 100K J 1/16W
R124,125 RK73FB2B470J CHIP R 47 J 1/8W HK R238 RK73HB1J000J CHIP R 0.0 J 1/16W

R127 RK73FB2B221J CHIP R 220 J 1/8W HK R240 RK73HB1J104J CHIP R 100K J 1/16W
R127 RK73FB2B271J CHIP R 270 J 1/8W K R242 RK73HB1J221J CHIP R 220 J 1/16W
R131 RK73HB1J221J CHIP R 220 J 1/16W R244 RK73HB1J000J CHIP R 0.0 J 1/16W
R135 RK73HB1J334J CHIP R 330K J 1/16W K R250 RK73HB1J000J CHIP R 0.0 J 1/16W
R135 RK73HB1J394J CHIP R 390K J 1/16W HK R256 RK73HB1J181J CHIP R 180 J 1/16W
R137 RK73EB2E241J CHIP R 240 J 1/4W R257 RK73HB1J000J CHIP R 0.0 J 1/16W
R138 RK73HB1J104J CHIP R 100K J 1/16W HK R261 RK73HB1J000J CHIP R 0.0 J 1/16W
R138-140 RK73HB1J104J CHIP R 100K J 1/16W K R263 RK73HB1J470J CHIP R 47 J 1/16W
R139 RK73HB1J124J CHIP R 120K J 1/16W HK R264 RK73HB1J472J CHIP R 4.7K J 1/16W
R141 RK73GB2A000J CHIP R 0.0 J 1/10W R266 RK73HB1J103J CHIP R 10K J 1/16W
R142 RK73HB1J824J CHIP R 820K J 1/16W K R268 RK73HB1J271J CHIP R 270 J 1/16W
R143,144 RK73HB1J104J CHIP R 100K J 1/16W HK R270 RK73HB1J680J CHIP R 68 J 1/16W

R144,145 RK73HB1J104J CHIP R 100K J 1/16W K R271 RK73HB1J222J CHIP R 2.2K J 1/16W
R145 RK73HB1J473J CHIP R 47K J 1/16W HK R273 RK73HB1J000J CHIP R 0.0 J 1/16W
R147 RK73HB1J822J CHIP R 8.2K J 1/16W R276 RK73GB2A330J CHIP R 33 J 1/10W

R150 R92-1061-05 JUMPER REST 0 OHM R279 RK73HB1J470J CHIP R 47 J 1/16W
R154 RK73EB2E241J CHIP R 240 J 1/4W R280 RK73HB1J102J CHIP R 1.0K J 1/16W
R161 RK73HB1J332J CHIP R 3.3K J 1/16W R282,283 RK73HB1J104J CHIP R 100K J 1/16W
R202 RK73HB1J470J CHIP R 47 J 1/16W R285 RK73HB1J000J CHIP R 0.0 J 1/16W
R203,204 RK73HB1J223J CHIP R 22K J 1/16W R286 RK73HB1J104J CHIP R 100K J 1/16W
R208 RK73HB1J153J CHIP R 15K J 1/16W R290,291 RK73HB1J104J CHIP R 100K J 1/16W
R209,210 RK73HB1J100J CHIP R 10 J 1/16W R292 RK73HB1J103J CHIP R 10K J 1/16W
R218,219 RK73HB1J103J CHIP R 10K J 1/16W R302 RK73HB1J000J CHIP R 0.0 J 1/16W
34
NX-700/700H
PARTS LIST
Ref. No. New
nation nation
R303 RK73HB1J104J CHIP R 100K J 1/16W R443 RK73HH1J223D CHIP R 22K D 1/16W
R304 RK73HB1J222J CHIP R 2.2K J 1/16W R444 RK73HB1J272J CHIP R 2.7K J 1/16W
R306 RK73HB1J472J CHIP R 4.7K J 1/16W R446 RK73GB2A100J CHIP R 10 J 1/10W
R310 RK73HB1J000J CHIP R 0.0 J 1/16W R448 RK73HB1J000J CHIP R 0.0 J 1/16W
R313 RK73HB1J000J CHIP R 0.0 J 1/16W R449 RK73GB2A220J CHIP R 22 J 1/10W
R314 RK73HB1J152J CHIP R 1.5K J 1/16W R450 RK73HB1J000J CHIP R 0.0 J 1/16W
R320-322 RK73HB1J000J CHIP R 0.0 J 1/16W R504 RK73HB1J104J CHIP R 100K J 1/16W
R324,325 RK73HB1J182J CHIP R 1.8K J 1/16W R506 RK73HB1J474J CHIP R 470K J 1/16W
R330 RK73GB2A100J CHIP R 10 J 1/10W R511 RK73HB1J220J CHIP R 22 J 1/16W

R332 RK73HB1J000J CHIP R 0.0 J 1/16W R514 RK73HB1J000J CHIP R 0.0 J 1/16W
R334 RK73HB1J000J CHIP R 0.0 J 1/16W R520,521 RK73HB1J473J CHIP R 47K J 1/16W
R340,341 RK73GB2A000J CHIP R 0.0 J 1/10W R524 RK73HB1J000J CHIP R 0.0 J 1/16W
R342,343 RK73HB1J000J CHIP R 0.0 J 1/16W R525 RK73HB1J104J CHIP R 100K J 1/16W
R347 RK73HB1J000J CHIP R 0.0 J 1/16W R528,529 RK73HB1J000J CHIP R 0.0 J 1/16W
R401 RK73HH1J105D CHIP R 1.0M D 1/16W R532 RK73HB1J101J CHIP R 100 J 1/16W
R402 RK73HB1J471J CHIP R 470 J 1/16W R533,534 RK73HB1J000J CHIP R 0.0 J 1/16W
R403 RK73HH1J104D CHIP R 100K D 1/16W R536,537 RK73HB1J000J CHIP R 0.0 J 1/16W
R405 RK73HH1J274D CHIP R 270K D 1/16W R539 RK73HB1J000J CHIP R 0.0 J 1/16W
R406 RK73HH1J104D CHIP R 100K D 1/16W R540,541 RK73HB1J101J CHIP R 100 J 1/16W
R408 RK73HB1J103J CHIP R 10K J 1/16W R543 RK73HB1J000J CHIP R 0.0 J 1/16W
R411 RK73HB1J104J CHIP R 100K J 1/16W R548 RK73GB2A000J CHIP R 0.0 J 1/10W
R415 RK73HB1J332J CHIP R 3.3K J 1/16W R552-554 RK73HB1J104J CHIP R 100K J 1/16W
R417 RK73HB1J473J CHIP R 47K J 1/16W R556-558 RK73HB1J104J CHIP R 100K J 1/16W
R423-425 RK73GB2A472J CHIP R 4.7K J 1/10W R567 RK73HB1J151J CHIP R 150 J 1/16W
R428,429 RK73HB1J103J CHIP R 10K J 1/16W R569 RK73HB1J220J CHIP R 22 J 1/16W
R430 RK73HH1J124D CHIP R 120K D 1/16W R572 RK73HB1J220J CHIP R 22 J 1/16W
R431 RK73HH1J183D CHIP R 18K D 1/16W R574 RK73GB2A000J CHIP R 0.0 J 1/10W
R432 RK73HH1J223D CHIP R 22K D 1/16W R575 RK73HB1J103J CHIP R 10K J 1/16W
R434 RK73HB1J330J CHIP R 33 J 1/16W R577 RK73HB1J102J CHIP R 1.0K J 1/16W
R435 RK73GB2A100J CHIP R 10 J 1/10W R578-580 RK73HB1J000J CHIP R 0.0 J 1/16W
R437 RK73HB1J474J CHIP R 470K J 1/16W R582-586 RK73HB1J000J CHIP R 0.0 J 1/16W
R440 RK73HB1J102J CHIP R 1.0K J 1/16W R588-590 RK73HB1J000J CHIP R 0.0 J 1/16W
R442 RK73HH1J334D CHIP R 330K D 1/16W R592,593 RK73HB1J000J CHIP R 0.0 J 1/16W
35
NX-700/700H
PARTS LIST
Ref. No. New
nation nation
R598-601 RK73FB2B102J CHIP R 1.0K J 1/8W R717 RK73HB1J473J CHIP R 47K J 1/16W
R607,608 RK73HB1J102J CHIP R 1.0K J 1/16W R724 RK73HB1J563J CHIP R 56K J 1/16W
R611,612 RK73HB1J105J CHIP R 1.0M J 1/16W R726 RK73HB1J100J CHIP R 10 J 1/16W
R615,616 RK73HB1J000J CHIP R 0.0 J 1/16W R728 RK73HB1J000J CHIP R 0.0 J 1/16W
R617-620 RK73HB1J102J CHIP R 1.0K J 1/16W R729 RK73HB1J104J CHIP R 100K J 1/16W
R623-625 RK73HB1J104J CHIP R 100K J 1/16W R731 RK73HB1J000J CHIP R 0.0 J 1/16W
R629 RK73HB1J105J CHIP R 1.0M J 1/16W R733 RK73HB1J333J CHIP R 33K J 1/16W
R633 RK73HB1J000J CHIP R 0.0 J 1/16W R738 RK73HB1J102J CHIP R 1.0K J 1/16W
R636 RK73HB1J000J CHIP R 0.0 J 1/16W R740,741 RK73HB1J104J CHIP R 100K J 1/16W
R650 RK73GB2A000J CHIP R 0.0 J 1/10W R752 RK73HB1J102J CHIP R 1.0K J 1/16W
R651 RK73FB2B102J CHIP R 1.0K J 1/8W R753 RK73HB1J563J CHIP R 56K J 1/16W
R656 RK73HB1J471J CHIP R 470 J 1/16W R758 RK73HB1J103J CHIP R 10K J 1/16W
R659-661 RK73HB1J104J CHIP R 100K J 1/16W R760 RK73HB1J152J CHIP R 1.5K J 1/16W
R664-674 RK73HB1J104J CHIP R 100K J 1/16W R762 RK73HB1J474J CHIP R 470K J 1/16W
R680-683 RK73HB1J000J CHIP R 0.0 J 1/16W R766 RK73HB1J104J CHIP R 100K J 1/16W
R684-686 RK73HB1J104J CHIP R 100K J 1/16W R767,768 RK73HB1J473J CHIP R 47K J 1/16W
R687,688 RK73HB1J472J CHIP R 4.7K J 1/16W R769 RK73HB1J472J CHIP R 4.7K J 1/16W
R691-696 RK73HB1J104J CHIP R 100K J 1/16W R771 RK73HB1J104J CHIP R 100K J 1/16W
36
NX-700/700H
PARTS LIST
Ref. No. New
nation nation
R784 RK73HB1J154J CHIP R 150K J 1/16W D19-21 HVC131 DIODE
R785 RK73HB1J103J CHIP R 10K J 1/16W D101 HVC131 DIODE
R786 RK73HB1J393J CHIP R 39K J 1/16W D102 02DZ5.6F-X,Y ZENER DIODE
R787 RK73HB1J274J CHIP R 270K J 1/16W D103,104 L407CDB DIODE (50V/1W) HK
R788 RK73HB1J223J CHIP R 22K J 1/16W D104 L407CDB DIODE (50V/1W) K
R789 RK73HB1J000J CHIP R 0.0 J 1/16W D105 L7091CER DIODE

R790 RK73HB1J224J CHIP R 220K J 1/16W D107-109 HSM88AS-E DIODE
R791 RK73HB1J564J CHIP R 560K J 1/16W D201,202 DAN235E DIODE
R792 RK73HB1J102J CHIP R 1.0K J 1/16W D205 HVC131 DIODE
R793,794 RK73HB1J000J CHIP R 0.0 J 1/16W D207-210 1SV283F VARIABLE CAPACITANCE DIODE
R795 RK73HB1J224J CHIP R 220K J 1/16W D213 1SV283F VARIABLE CAPACITANCE DIODE
R796 RK73HB1J103J CHIP R 10K J 1/16W D215 HVC131 DIODE
R797 RK73HB1J334J CHIP R 330K J 1/16W D216-218 1SV283F VARIABLE CAPACITANCE DIODE
R798 RK73HB1J684J CHIP R 680K J 1/16W D401 02DZ18F-X ZENER DIODE
R799 RK73HB1J563J CHIP R 56K J 1/16W D403 1SS416 DIODE
R800 RK73HB1J472J CHIP R 4.7K J 1/16W D404 22ZR-10D SURGE ABSORBER

R801 RK73HB1J104J CHIP R 100K J 1/16W D405 DSA3A1 DIODE
R802 RK73HB1J273J CHIP R 27K J 1/16W D406 HSC119 DIODE
R803 RK73HB1J153J CHIP R 15K J 1/16W D407 CRS02-Q DIODE
R804 RK73HB1J681J CHIP R 680 J 1/16W D408 1SS301F DIODE
R805 RK73HB1J823J CHIP R 82K J 1/16W D409-412 1SS388F DIODE

R806 RK73HB1J562J CHIP R 5.6K J 1/16W D501,502 1SS388F DIODE
R807,808 RK73HB1J103J CHIP R 10K J 1/16W D503,504 1SS416 DIODE
R809 RK73HB1J104J CHIP R 100K J 1/16W D506,507 1SS416 DIODE
R810 RK73HB1J102J CHIP R 1.0K J 1/16W D508 DA204U DIODE
R812,813 RK73HB1J472J CHIP R 4.7K J 1/16W D509,510 1SS416 DIODE

R814-816 RK73HB1J104J CHIP R 100K J 1/16W D511,512 DA204U DIODE
R817 RK73HB1J473J CHIP R 47K J 1/16W D702 HSC119 DIODE
R818 RK73HB1J333J CHIP R 33K J 1/16W D703-705 RB706F-40 DIODE
R819 RK73HB1J000J CHIP R 0.0 J 1/16W D706,707 EMZ6.8N ZENER DIODE
R820 RK73HB1J474J CHIP R 470K J 1/16W D901-904 DA204U DIODE

R821 RK73HB1J000J CHIP R 0.0 J 1/16W D905,906 02DZ18F-X ZENER DIODE
R822 RK73HB1J101J CHIP R 100 J 1/16W D907,908 DA204U DIODE
R823 RK73HB1J472J CHIP R 4.7K J 1/16W D909 1SS355 DIODE
R825,826 RK73HB1J103J CHIP R 10K J 1/16W D910 02DZ18F-X ZENER DIODE
R827 RK73HB1J332J CHIP R 3.3K J 1/16W D911,912 DA204U DIODE

R828 RK73HB1J000J CHIP R 0.0 J 1/16W D913 1SS355 DIODE
R831 RK73HB1J000J CHIP R 0.0 J 1/16W D914 02DZ18F-X ZENER DIODE
R833-835 RK73HB1J101J CHIP R 100 J 1/16W IC1 LMC7101BIM5 MOS-IC
R836 RK73HB1J000J CHIP R 0.0 J 1/16W IC2 LM73CIMKX-0 MOS-IC
R837 RK73HB1J472J CHIP R 4.7K J 1/16W IC3 Note 1 MOS-IC

R838 RK73HB1J000J CHIP R 0.0 J 1/16W IC4 LMC7101BIM5 MOS-IC
R841 RK73HB1J000J CHIP R 0.0 J 1/16W IC5 TC75W51FK(F) MOS-IC
R842 RK73FB2B102J CHIP R 1.0K J 1/8W IC101 NJM2904V-ZB MOS-IC
R843 RK73HB1J471J CHIP R 470 J 1/16W IC102 2A RA30H1317M123 MOS-IC K
R845 RK73HB1J102J CHIP R 1.0K J 1/16W IC102 2A RA60H13171123 MOS-IC HK

R846 RK73HB1J332J CHIP R 3.3K J 1/16W IC103 NJM2904V-ZB MOS-IC
R901 RK73GB2A471J CHIP R 470 J 1/10W IC201 MCP6021-E/OT MOS-IC
R902,903 RK73HB1J101J CHIP R 100 J 1/16W IC202 TK10931VTL-G ANALOGUE IC
R904-913 RK73HB1J471J CHIP R 470 J 1/16W IC203 TC75W51FK(F) MOS-IC
R914 RK73GB2A471J CHIP R 470 J 1/10W IC204 SPM5001 MOS-IC

R915 RK73HB1J000J CHIP R 0.0 J 1/16W IC205,206 LMC7101BIM5 MOS-IC
R918,919 RK73HB1J000J CHIP R 0.0 J 1/16W IC401 XC6108C23CMN MOS-IC
R921 RK73HB1J474J CHIP R 470K J 1/16W IC402 XC6204B332P1 ANALOGUE IC
R922 RK73HB1J000J CHIP R 0.0 J 1/16W IC403 2A NJM78M08FA-ZB ANALOGUE IC
D3 DA221 DIODE IC404 TA7805FQ MOS-IC

D5,6 HVC131 DIODE IC405 LT1616ES6-PBF ANALOGUE IC
D7,8 1SV325F VARIABLE CAPACITANCE DIODE IC406 TK71733S BI-POLAR IC
D11-16 1SV282-F VARIABLE CAPACITANCE DIODE IC407,408 XC6204B332M MOS-IC
D18 1SV278F VARIABLE CAPACITANCE DIODE IC409 XC6205B152PRN ANALOGUE IC
Note 1: This part cannot be replaced. Therefore, this part is not supplied as a service part. 37
If a part reference number is listed in a shaded box, that part does not come with the PCB.
NX-700/700H
PARTS LIST
Ref. No. New
nation nation
IC410 XC9101D09AKR ANALOGUE IC Q413-415 DTC114EE DIGITAL TRANSISTOR
IC501 Note 1 (BGA) ROM IC Q416 SSM6L05FU-F FET
IC502 Note 1 (BGA) MICROPROCESSOR IC Q417 SSM5H01TU-F FET
IC503 Note 1 (BGA) SRAM IC Q501 UPA672T-A FET
IC504 RV5C386A MOS-IC Q701 SSM3K15TE(F) FET
IC505 TC7SH08FU-F MOS-IC Q702 2SC4617(Q) TRANSISTOR

IC506 XC6109C29ANN ANALOGUE IC Q703 SSM3K15TE(F) FET
IC507 TC7SH126FU-F MOS-IC Q704 2SC4738(GR)F TRANSISTOR
IC508 SM5023CNDH-G MOS-IC Q705 2SA1832(GR)F TRANSISTOR
IC509 TC7WT125FUF MOS-IC Q706,707 2SJ243-A FET
IC510 Note 1 (BGA) MOS-IC Q708 2SA1832(GR)F TRANSISTOR

IC511 TC7SH08FU-F MOS-IC Q709 DTC114EE DIGITAL TRANSISTOR
IC512,513 TC7SET08FU-F MOS-IC Q710 DTC363EU DIGITAL TRANSISTOR
IC514 TC7WBD125AFK MOS-IC Q901,902 QSX6 TRANSISTOR
IC515 TC7WT126FU-F MOS-IC TH101,102 ERTJ0EV104H THERMISTOR
IC516 TC7WH126FU-F MOS-IC TH701 ERTJ0EV104H THERMISTOR

IC517 Note 1 MOS-IC
IC518 ADM202EARNZ MOS-IC
IC702,703 TC75W51FK(F) MOS-IC
IC704 MCP6021-E/OT MOS-IC

IC709 TC75W51FK(F) MOS-IC

IC712 M62364FP-F MOS-IC
IC715 2A LA4425A MOS-IC
Q1 2SC5383-T111 TRANSISTOR
Q2 DTA114YE DIGITAL TRANSISTOR
Q3 SSM3K15TE(F) FET
Q5 EMD9 TRANSISTOR
Q6 2SC5636 TRANSISTOR
Q7 2SC5383-T111 TRANSISTOR
Q9,10 2SK508NV(K52) FET
Q11 SSM6L05FU-F FET
Q12 2SJ347F FET
Q13,14 2SC5636 TRANSISTOR
Q15 2SK1215-E(E) FET

Q101 2SC5108(Y)F TRANSISTOR
Q102 2SC5455-A TRANSISTOR
Q105 DTC114EE DIGITAL TRANSISTOR
Q106 2SK1830F FET
Q201 DTA114EE DIGITAL TRANSISTOR

Q202 DTC144EE DIGITAL TRANSISTOR
Q204,205 2SC3356(R23) TRANSISTOR
Q210 2SC3357-A TRANSISTOR

Q212 EMD9 TRANSISTOR
Q401,402 DTC114EE DIGITAL TRANSISTOR
Q403 DTC114TE DIGITAL TRANSISTOR
Q404 2SJ645 FET
Q405 2SA1955A-F TRANSISTOR

Q406 UPA672T-A FET
Q407-409 12A02CH TRANSISTOR
Q410 SSM3K15TE(F) FET
Q411,412 2SA1955A-F TRANSISTOR
38 Note 1: This part cannot be replaced. Therefore, this part is not supplied as a service part.
NX-700/700H
EXPLODED VIEW
A B
1
A : N09-2292-05
B M3 x 8 : N67-3008-48
C M2.6 x 6 (Br-Tap) : N87-2606-43
D M2.6 x 8 (Br-Tap) : N87-2608-48
27
26
1 D Cx2
D
Dx3
30
Dx2
Dx3
B
B
19
20
Dx2 D
X57 31
X57 IC715 13 Cx2
IC403 Cx2
61 IC102 29
D Bx2
Dx2
16
D 33 18
TX-RX unit A/2 D 11
(X57-)
15 28
2 Dx2
32
A
TX-RX unit B/2 D
(X57-) A
D
48
34
4 D
701 35 D
10 24
24
702 46
Display unit
47 (X54-)
704 54
36 5
703 706 705 24
3 6
7 24
707 50 14
49
52
2 58
45
Parts with the exploded numbers larger than 700 are not supplied.
If a part reference number is listed in a box on the exploded view of the PCB (for example, IC123 ), that part does not come with
39
the PCB. These parts must be ordered separately.
NX-700/700H
PACKING
C D
711
59 Microphone
(T91-0639-35) 8 Instruction manual
(B62-2000-00)
712
1
21 Fuse (Blade type)15A/32V

(F52-0024-05)
44 Mic holder
(J19-1584-15)
39 Packing fixture
(H12-4235-05)
12 DC cord assy
(E30-7523-35)
56 Screw set 51 Bracket

(N99-2039-05) 40 Packing fixture
(J29-0726-03)
(H12-4236-05)
38 Inner carton case

(H02-0630-03)
41 Item carton case

(H52-2195-02) : K
(H52-2196-02) : HK
40 Parts with the exploded numbers larger than 700 are not supplied.
NX-700/700H
TROUBLE SHOOTING
Fault diagnosis of the BGA (Ball Grid Array) IC
Overview: A flowchart for determining whether or not the transceiver can be powered on (the LCD does not function even if
the power switch is turned on) due to broken BGA parts.
BGA parts: ASIC (IC510), DSP (IC502), FLASH (IC501), SRAM (IC503)
When the BGA IC is problematic, please bring the printed circuit board (X57-7380-XX) in for service. Various ESN/default adjust-
ment values are written on the printed circuit board for service. Additionally various ESN stickers are included. The power mod-
ule (RA30H1317M123: K, RA60H13171123: HK), short connector (E37-1180-05) and button type lithium battery (W09-0971-05)
do not belong to the printed circuit board for service. Please use the part which has been attached to the printed circuit board.
After the printed circuit board has been readjusted, please attach any ESN stickers to the chassis. When “ESN Validation” is
used with NXDN Trunking, you must modify the ESN register.
● Checking power supply voltage

Checking voltage Checking for an abnormal point
When an abnormal
Points to be checked Normal voltage value is confirmed. 33M has an abnormal voltage.
33M IC402 (5 pin) 3.3V [ASIC]
15M IC409 (5 pin) 1.5V Remove L508 to check the voltage of the 33M.
33A IC408 (5 pin) 3.3V If the voltage becomes normal, the ASIC is broken.
33BU D411 (Cathode side) 3.3V [DSP]
Remove L503 to check the voltage of the 33M.
Power supply of each device is connected through the coil. If the voltage becomes normal, the DSP is broken.
[ASIC] [FLASH]
33M: L903, 15M: L511, 33A: R603 Remove L501 to check the voltage of the 33M.
[DSP] If the voltage becomes normal, the FLASH is broken.
33M: L503, 15M: L502
[FLASH] 15M has an abnormal voltage.
33M: L501 [ASIC]
[SRAM] Remove L511 to check the voltage of the 15M.
33BU: L522 If the voltage becomes normal, the ASIC is broken.
[DSP]
When a normal Remove L502 to check the voltage of the 15M.
● Checking the clock value is confirmed. If the voltage becomes normal, the DSP is broken.
Checking the clock
When an abnormal 33A has an abnormal voltage.
Points to be checked Normal voltage (3.3V) value is confirmed. [ASIC]
18.432MHz ASIC side R569 18.432MHz Remove R603 to check the voltage of the 33A.
DSP side R511 18.432MHz If the voltage becomes normal, the ASIC is broken.
32.768kHz IC504 (1 pin) or R545 32.768kHz
33BU has an abnormal voltage.
When a normal [SRAM]
● Checking the Reset/Control signal value is confirmed. Remove L522 to check the voltage of the 33BU.
Checking the control signal input to the ASIC If the voltage becomes normal, the SRAM is broken.
When an abnormal
Points to be checked Normal voltage value is confirmed. If the voltage is not corrected, there is a problem
RST (RESET) IC506 (4 pin) 3.3V other than the BGA parts.
/BINT IC401 (1 pin) 3.3V
/OVRB D403 (Cathode side) 3.3V
Remove the R569, R511 and R545. If it oscillates
When a normal normally, the DSP and ASIC may be broken.
value is confirmed.
Checking the ASIC input switch signal
*Each signal is not masked by the setting of the FPU. The BGA parts are not broken.
The POWER key is pressed and held. When an abnormal
Points to be checked Confirmed voltage value is confirmed.
/PSW (R619) 0V
The ignition key is kept ON.
Points to be checked Confirmed voltage
/IGN (R618) 0V
● Checking the output signal When a normal If the /FRST is always 0V, the ASIC is broken.
from the ASIC value is confirmed. When an abnormal
Points to be checked Normal voltage value is confirmed. If the /FRST repeats 3.3V and 0V at intervals,
/FRST R509 3.3V the ASIC, FLASH and SRAM may be broken.
When a normal
value is confirmed.
41
NX-700/700H
TROUBLE SHOOTING
● Checking the signal output from When a normal

the ASIC by software control value is confirmed. When an abnormal
Points to be checked Normal voltage value is confirmed. Remove R408. If the ASIC side is 0V,
SBC R408 3.3V the ASIC/FALSH/SRAM may be broken.
When a normal
value is confirmed. When an abnormal
Points to be checked Normal voltage value is confirmed.
If the /DRST is 0V, the ASIC/FALSH/SRAM are broken.
/DRST R841 3.3V
When a normal
● Panel control (TX-RX unit) value is confirmed. When an abnormal
Points to be checked Normal voltage value is confirmed. Remove the Q501. If the ASIC side is 0V,
/PRST R506 (Signal side) 3.3V the ASIC/FALSH/SRAM may be broken.
When a normal
value is confirmed. When an abnormal
Points to be checked Normal voltage value is confirmed. If the SBC is 3.3V and 80C regulator IC403 (pin 1)
80C C581 (Signal side) 8.0V input side is 8.5V or more, the BGA parts are not broken.
When a normal When an abnormal
● Panel control (Panel unit) value is confirmed. value is confirmed.
Checking voltage The BGA parts are not broken.
Points to be checked Normal voltage
5C IC903 (5 pin) 5.0V
33C IC904 (5 pin) 3.3V
When a normal
value is confirmed.
Checking the clock/reset
Points to be checked Normal voltage
Xout R949 11.059MHz (5.0V)
/PRST R947 (Signal side) 5.0V When an abnormal
FLASH R986 3.3V value is confirmed.
When a normal
value is confirmed.
Checking the Control signal When an abnormal
/CS0 IC911 (48 pin) 3.3V→0V→3.3V
/RD IC911 (42 pin) 3.3V→0V→3.3V
If nothing is displayed even after replacing the panel,
When a normal the BGA may be broken.
value is confirmed.
When an abnormal The panel microcomputer receives a request of LCD
Checking the Control signal display from the ASIC. Then, the LCD displays.
The /LCDRST and /CS3 signal become abnormal if
/LCDRST R991 (Signal side) 3.3V communication is disabled due to a trouble in
/CS3 IC912 (7 pin) 3.3V→0V→3.3V the ASIC.
When a normal
value is confirmed.
It is unlikely that the BGA parts are broken.
● When an error display appears on the LCD.

An error occurs when the ASIC internal RAM reads
The LCD displays “INIT ERROR1”.
or writes. The ASIC may be broken.
An error occurs when the DSP internal RAM reads

or writes. The DSP may be broken.
An error occurs when the SRAM internal RAM

reads or writes. The SRAM may be broken.
42
NX-700/700H
TROUBLE SHOOTING
Replacing TX-RX Unit ■ After Changing the PCB
1. After changing the printed circuit board, write the up-
■ TX-RX Unit Information to-date Firmware following the instructions in the “RE-
Original For Service ALIGNMENT - 6.Firmware Programming Mode”.
Model Name
TX-RX Unit Number TX-RX Unit Number 2. Using the KPG-111D, select your desired item (Model
NX-700 (K) X57-7380-10 X57-7380-11 Name and Frequency) from the Model> Product Informa-
tion menu, then use Program> Write to the Transceiver
NX-700H (K) X57-7380-12 X57-7380-13 to write the FPU data (PC Programming mode).
3. Enter Program> Test Mode, then adjust the various ad-
■ Method of confirming “Original TX-RX unit” and justment data (PC Test Mode) as described in the “AD-
“Service TX-RX Unit” JUSTMENT”.
4. Attach the new labels corresponding to the new printed
circuit board. (Refer to the images below for label place-
ment.)
5. If necessary, write the FPU data used by the customer
with the KPG-111D.
Note:
X57-738 A/2
Component side
• When using the ESN Validation function of NXDN Trunk-
ing, the NXDN ESN number changes when the circuit
board is changed (the number is written on the circuit
board); the NXDN Trunking System cannot be accessed.
Use the KPG-110SM on the NXDN Trunking System side
CN595 to reprogram the NXDN ESN number.
• When a new printed circuit board is used, the Kenwood
ESN changes, as does the Transceiver information dis-
Silk print play of the KPG-111D, but this does not have any effect
on the operation of the transceiver.
• If changing to the original Kenwood ESN and NXDN ESN,
please contact our service center.
Kenwood ESN lable
Check box
The corresponding
TX-RX unit is checked.
Cut-off Line
■ Supplied Accessories of “Service TX-RX Unit”
Product Number NXDN ESN
Item (Including Parts Number) Quantity Label (16 digits) Label (12 digits)
TX-RX Unit 1
Kenwood ESN Label 1
NXDN ESN Label 1
Product Number Label 1
Addendum (B59-2533-XX) 1
■ “Service TX-RX Unit” Data

The following data is written on the service unit:
• Firmware
• FPU Data
• Various Adjustment Data
• Kenwood ESN (“S” is given after the model name.)
• NXDN ESN / Product number
NX-700/700H
Note: A UPC code and UPC barcode is not printed on the

Kenwood ESN Label. If necessary, cut the label at the cut-
off line and attach only the serial number.
43
NX-700/700H
ADJUSTMENT
Controls “FNC” not appears on the sub LCD display
Key
Function Display
Power switch
Volume Up/Down key Channel Up/Down key Microphone key
[PTT] Transmit -
Use as the DTMF keypad.
[0] to [9]
If a key is pressed during
and [A]
transmission, the DTMF -
to [D],
corresponding to the key
[#], [ ]
that was presses is sent.
Modular Programmable function keys
MIC jack
“FNC” appears on the sub LCD display
KMC-36 Key
Function Display
[PTT] [ ] -
Keypad Analog: “A”
[ ] Analog/NXDN
[HOOK] NXDN: “N”
[ ]/[ ] Function off -
[ ] - -
[ ] LCD all lights LCD all point appears
[ ] High power/Low power Low: icon appears
[ ] Function off -
[ ] Compander on/off On: icon appears
Panel Test Mode [ ] Beat shift on/off On: icon appears
■ Test mode operation features Microphone key

This transceiver has a test mode. To enter test mode, [PTT] Transmit
press and hold the [ ] key while turning the transceiver
[0] to [9]
power ON. Before the transceiver enters test mode, the and [A]
frequency version information appears on the LCD mo- Function off -
to [D],
mentarily. Test mode can be inhibited by programming. To [#], [ ]
exit test mode, turn the transceiver power OFF. The follow-
ing functions are available in test mode.
• LED indicator
■ Key operation Red LED Lights during transmission.
Green LED Lights when there is carrier.
“FNC” not appears on the sub LCD display
Key
Function Display • Sub LCD indicator
“FNC” Appears at function on.
[ ]/[ ] Test CH up/down Channel No.
[ ]/[ ] Volume up/down - • LCD display in panel test mode
Push: Squelch level up Squelch level
[ ] Temperature
Hold: Squelch off Squelch off: icon appears
Wide: “w”
Sub LCD display +25
[ ] Wide/Narrow/Very narrow Narrow: “n”
Very narrow: “v” Main LCD display An SQ5 1- 1
[ ] Shift to panel tuning mode -
Signaling No.
“FNC” appears on the sub
[ ] Function on Channel No.
LCD display Squelch level
[ ] MSK 1200bps and 2400bps 2400bps: icon appears (Analog mode only)
An : Analog narrow mode
[ ] Test signaling CH up Signaling No. Aw : Analog wide mode
Nn : NXDN narrow mode
Nv : NXDN very narrow mode
44
NX-700/700H
ADJUSTMENT
■ Frequency and Signaling Panel Tuning Mode
The transceiver has been adjusted for the frequencies
shown in the following table. When required, readjust them ■ Preparations for tuning the transceiver
following the adjustment procedure to obtain the frequen- Before attempting to tune the transceiver, connect the
cies you want in actual operation. unit to a suitable power supply.
Whenever the transmitter is turned, the unit must be
connected to a suitable dummy load (i.e. power meter).
• Test frequency
The speaker output connector must be terminated with
CH RX (MHz) TX (MHz) a 4Ω dummy load and connected to an AC voltmeter and an
1 155.05000 155.10000 audio distortion meter or a SINAD measurement meter at all
times during tuning.
2 136.05000 136.10000
3 173.95000 173.90000 ■ Transceiver tuning (To enter tuning mode)
To enter tuning mode, press the [ ] key while the trans-
4 155.00000 155.00000
ceiver is in test mode. Use the [ ] key to write tuning data
5 155.20000 155.20000 through tuning modes, and the [ ]/[ ] key to adjust tuning
6 155.40000 155.40000 requirements (1 to 4096 appears on the LCD).
Use the [ ] key to select the adjustment item through
7~16 - - tuning modes. Use the [ ] key to adjust 5 reference level
adjustments, and use the [ ] key to switch between Wide/
• Analog mode signaling Narrow/Very narrow.
No. RX TX
• LCD display in panel tuning mode
1 None None
CV voltage, AD value, etc
2 None 100Hz Square Wave
LTR Data : LTR Data : Sub LCD display 2.6
3
AREA=0, GOTO=12 AREA=0, GOTO=12 Main LCD display An CNTR 256
HOME=12 HOME=12
ID=47, FREE=25 ID=47, FREE=25
Adjustment Adjustment value
4 QT: 67.0Hz QT: 67.0Hz point (1~4096)
L,L’,C,H’,H Proper value guide
5 QT: 151.4Hz QT: 151.4Hz
An: Analog narrow mode (When the frequency
6 QT: 210.7Hz QT: 210.7Hz Aw: Analog wide mode adjustment is necessary,
Nn: NXDN narrow mode ▼ or ▲ is displayed.)
7 QT: 254.1Hz QT: 254.1Hz
Nv: NXDN very narrow mode Adjustment item
8 DQT: D023N DQT: D023N
9 DQT: D754I DQT: D754I ■ Key operation
10 DTMF: 159D DTMF: 159D Function
Key
11 None DTMF Code 9 Push Hold (1 second)
2-tone : 2-tone : [ ]/[ ] Adjustment value up/down Continuation up/down
12 A: 304.7Hz A: 304.7Hz
[ ]/[ ] Volume up/down Continuation up/down
B: 3106.0Hz B: 3106.0Hz
[ ] Auto adjustment start -
13 Single Tone: 979.9Hz Single Tone: 979.9Hz
[ ] Wide/Narrow/Very narrow -
14 None Single Tone: 1000Hz
[ ] Shift to panel test mode -
15 None MSK
To enter 5 reference level
16 MSK MSK [ ] -
adjustments L/L’/C/H’/H
Writes the adjustment
[ ] -
• NXDN mode signaling value
No. RX TX [ ] Go to next adjustment item Back to last adjustment item
1 RAN1 RAN1 Microphone key
2 None PN9 [PTT] Transmit -
3 RAN1 Maximum deviation pattern [0] to [9]

and [A]
RAN: Radio Access Number - -
to [D],
PN9: Pseudo-Random Pattern (For production only) [#], [ ]
45
NX-700/700H
ADJUSTMENT
■ 5 reference level adjustments frequency
Tuning point RX (MHz) TX (MHz)
Low 136.05000 136.10000
Low’ 145.55000 145.60000
Center 155.05000 155.10000
High’ 164.55000 164.60000
High 173.95000 173.90000
■ Adjustment item and Display

Aw (Analog An (Analog Nn (NXDN Nv (NXDN
Adjusutment Main LCD Wide) Narrow) Narrow) Very Narrow) Adjust item
Order Sub-LCD display
item display Number
Adjustment range
1 point ADJ Common
1 LCD contrast CNTR -
1~256 Section 2
5 point ADJ Common

2 Receive Assist RAST (CV voltage)
1~4096 Section 3
5 point ADJ Common

3 Transmit Assist TAST (CV voltage)
1~4096 Section 3
RTC 1 point ADJ Common

4 RTC -
(Real-time clock) –62~ –1/0/+1~ +62 Section 4
High Transmit - 5 - - Transmitter

5 HILMT -
Power Limit 1~256 Section 1
Low Transmit - 5 - - Transmitter

6 LOLMT -
Power Limit 1~256 Section 2
High Transmit - 5 - - Transmitter

7 HIPWR -
Power 1~1024 Section 3
Low Transmit - 5 - - Transmitter

8 LOPWR -
Power 1~1024 Section 4
(Encode - 5 - - Transmitter
9 Balance BAL
frequency) 1~256 Section 5
Maximum - - 5 5 Transmitter
10 NDEV -
Deviation (NXDN) 1~1024 Section 6
Maximum 5 5 - - Transmitter
11 ADEV -
Deviation (Analog) 1~1024 Section 7
1 1 - - Transmitter
12 QT Deviation QT -
1~1024 Section 8
1 1 - - Transmitter
13 DQT Deviation DQT -
1~1024 Section 9
1 1 - - Transmitter
14 LTR Deviation LTR -
1~1024 Section 10
1 1 - - Transmitter
15 DTMF Deviation DTMF -
1~1024 Section 11
Single Tone 1 1 - - Transmitter

16 TONE -
Deviation 1~1024 Section 12
1 1 - - Transmitter
17 MSK Deviation MSK -
1~1024 Section 13
46
NX-700/700H
ADJUSTMENT
Aw (Analog An (Analog Nn (NXDN Nv (NXDN
Adjusutment Main LCD Wide) Narrow) Narrow) Very Narrow) Adjust item
Order Sub-LCD display
item display Number
Adjustment range
- - - 1 Transmitter
18 CWID Deviation CWID -
1~1024 Section 14
(RSSI measurement - 5 - - Receive

19 Sensitivity 1 SENS1
value) 1~256 Section 2
(RSSI measurement - 5 - - Receive

20 Sensitivity 2 SENS2
(RSSI measurement 5 5 - *1 5 Receive

21 RSSI Reference RRSSI
(ASQDET 5 5 - *1 5 Receive
22 Open Squelch SQL
measurement value) 1~256 Section 5

23 Low RSSI LRSSI

24 High RSSI HRSSI
(ASQDET 5 5 - - Receive
25 Tight Squelch SQLT
measurement value) 1~256 Section 8
*1: Because NXDN Narrow adjusted by adjusting Analog Narrow, it is not necessary to adjust NXDN Narrow.
■ Panel tuning mode flow chart
Panel test mode

[ ]
Adjustment Item
LCD Display N/W/VN
[ ] hold
For all adjustment items, press the
LCD Contrast [ ] key to write the adjustment value.
CNTR
[ ] press [ ] hold
RX Assist [ ] 5 reference level
RAST Adjustments
[ ] press [ ] hold
TX Assist [ ] 5 reference level 5 reference level Low [ ] Adjustment Point
TAST Adjustments Adjustments L LCD Display
[ ] press [ ] hold [ ]
RTC Low-Center [ ]
RTC L’
High Power Limit [ ] 5 reference level Center [ ]
HILMT Adjustments C
Low ower Limit [ ] 5 reference level Center-High [ ]
LOLMT Adjustments H’
High Power [ ] 5 reference level High [ ]
Narrow Adjustments H
HIPWR
Low Power [ ] 5 reference level
Narrow 5 reference level
LOPWR Adjustments Adjustments exit
[ ] press [ ] hold
Balance [ ] 5 reference level
Narrow Adjustments
BAL
[ ] press [ ] hold
47
NX-700/700H
ADJUSTMENT
NXDN Deviation [■] NXDN Deviation Very

Narrow
NDEV NDEV Narrow
[ ] press [ ] hold [ ] [ ] 5 reference level
Adjustments
Analog MAX Deviation [■] Analog MAX Deviation

Narrow Wide
ADEV ADEV
Adjustments
QT Deviation [■] QT Deviation

Narrow Wide
QT QT
[ ] press [ ] hold
DQT Deviation [■] DQT Deviation
Narrow Wide
DQT DQT
[ ] press [ ] hold
LTR Deviation [■] LTR Deviation
Narrow Wide
LTR LTR
[ ] press [ ] hold
DTMF Deviation [■] DTMF Deviation
Narrow Wide
DTMF DTMF
[ ] press [ ] hold
Single Tone Deviation [■] Single Tone Deviation
Narrow Wide
TONE TONE
[ ] press [ ] hold
MSK Deviation [■] MSK Deviation
Narrow Wide
MSK MSK
[ ] press [ ] hold
CW ID Deviation Very
CWID Narrow
[ ] press [ ] hold
Sensitivity 1 [ ] 5 reference level
Narrow
SENS1 Adjustments
[ ] press [ ] hold
Sensitivity 2 [ ] 5 reference level
Narrow Adjustments
SENS2
[ ] press [ ] hold
RSSI (Reference) [■] RSSI (Reference) [■] RSSI (Reference) Very [■]
Narrow Wide
RRSSI RRSSI RRSSI Narrow
[ ] press [ ] hold [ ] [ ] [ ] 5 reference level
Adjustments
Squelch (Open) [■] Squelch (Open) [■] Squelch (Open) Very [■]
Narrow Wide
SQL SQL SQL Narrow
Adjustments
RSSI (Low) [■] RSSI (Low) [■] RSSI (Low) Very [■]
Narrow Wide
LRSSI LRSSI LRSSI Narrow
Adjustments
RSSI (High) [■] RSSI (High) [■] RSSI (High) Very [■]
Narrow Wide
HRSSI HRSSI HRSSI Narrow
Adjustments
Squelch (Tight) [■] Squelch (Tight)

Narrow Wide
SQLT SQLT
Adjustments
48
NX-700/700H
ADJUSTMENT
Test Equipment Required for Alignment
Test Equipment Major Specifications
Frequency Range 136 to 174MHz
Modulation Frequency modulation and external modulation
1. Standard Signal Generator Output –127dBm/0.1µV to greater than –20dBm/22.4mV
(SSG) When performing the Frequency adjustment, the following accuracy is necessary.
• 0.003ppm
Use a standard oscillator for adjustments, if necessary.
Input Impedance 50Ω
2. Power Meter Operation Frequency 136 to 174MHz
Measurement Capability Vicinity of 100W
3. Deviation Meter Frequency Range 136 to 174MHz
Measuring Range 10mV to 20V DC
4. Digital Volt Meter (DVM)
Input Impedance High input impedance for minimum circuit loading
5. Oscilloscope DC through 30MHz
6. High Sensitivity Frequency Range 10Hz to 1000MHz
Frequency Counter Frequency Stability 0.01ppm or less
7. Ammeter 20A or more
Frequency Range 50Hz to 10kHz
8. AF Volt Meter (AF VTVM)
Voltage Range 1mV to 10V
Frequency Range 50Hz to 5kHz or more
9. Audio Generator (AG)
Output 0 to 1V
Capability 3% or less at 1kHz
10. Distortion Meter
Input Level 50mV to 10Vrms
11. 4Ω Dummy Load Approx. 4Ω, 20W
13.6V, approx. 20A (adjustable from 9V to 20V)
12. Regulated Power Supply
Useful if ammeter equipped
Frequency Range 40MHz to 520MHz
Input Level Up to +20dBm
13. Spectrum Analyzer Input Sensitivity –100dBm
Resolution Bandwidth 100Hz
Video Bandwidth 100Hz
Frequency Range 40MHz to 520MHz
14. Tracking Generator
Output Level –30dBm to 0dBm
Test cable for microphone input (E30-3360-08) Tuning cable (E30-3383-05)

Adapter cable (E30-3383-05) is required for injecting an au-
GREEN dio if PC tuning is used.
1 1
RED See “PC Mode” section fot the connection.
2 2
BLACK E
3 3
BLUE PTT
4 4
SHIELD MIC-E
5 5
WHITE MIC
6 6
GRAY HK
7 7
YELLOW
8 8
MIC connector (Front panel view)

Lead wire +
1 : BLC/AFO Shield wire –
MIC
2 : +B
8 3 : GND
4 : PTT/TXD (PC serial data from radio)
5 : MICE
1 6 : MIC
7 : HOOK/RXD (PC serial data to radio)
8 : DM/KVL
49
NX-700/700H
ADJUSTMENT
Radio Check Section
Condition Measurement Adjustment
Specifications /
Item Test-
Panel test mode PC test mode Unit Terminal Unit Parts Method Remarks
equipment
1. Frequency 1) CH-Sig: 1-1 1) Test Channel f. counter Panel ANT Check an internal ±0.5ppm
check PTT: ON Channel: 1 temperature of –77.55Hz~
Test Signaling radio within 25˚C ± +77.55Hz
Mode: Analog 2˚C. @155.1MHz
Signaling: 1
PTT: Press
[Transmit] button.
2. High 1) CH-Sig: 1-1 1) Test Channel Power Check 25W~35W

power PTT: ON Channel: 1 meter 9.0A or less K
check Test Signaling Ammeter
Mode: Analog 45W~55W
Signaling: 1 13A or less HK
PTT: Press
[Transmit] button.
2) CH-Sig: 2-1 2) Test Channel
PTT: ON Channel: 2
Test Signaling
Mode: Analog
Signaling: 1
PTT: Press
[Transmit] button.
PTT: ON Channel: 3
Test Signaling
Mode: Analog
Signaling: 1
PTT: Press
[Transmit] button.
3. Low 1) CH-Sig: 1-1 1) Test Channel 3.5W~6.5W

power PTT: ON Channel: 1 5.0A or less K
check Test Signaling
Mode: Analog 7W~13W
Signaling: 1 8A or less HK
PTT: Press
[Transmit] button.
PTT: ON Channel: 2
Test Signaling
Mode: Analog
Signaling: 1
PTT: Press
[Transmit] button.
PTT: ON Channel: 3
Test Signaling
Mode: Analog
Signaling: 1
PTT: Press
[Transmit] button.
4. MIC 1) CH-Sig: 1-1 1) Test Channel Deviation Adjust AG input Dev: 3kHz at
sensitivity AG: 1kHz Channel: 1 meter to get a standard 5mV±1mV
check PTT: ON Test Signaling Oscilloscope MOD.
Mode: Analog AG
Signaling: 1 AF VTVM
AG: 1kHz
PTT: Press
[Transmit] button.
50
NX-700/700H
ADJUSTMENT
Specifications /
Item Test-
equipment
5. Sensitivity 1) CH-Sig : 1-1 1) Test Channel SSG ANT Check 12dB SINAD or
check SSG output Channel: 1 AF VTVM EXT SP more
Wide: Test Signaling Oscilloscope connec-
–117dBm (0.32µV) Mode: Analog Distortion tor
(MOD: 1kHz/±3kHz) Signaling: 1 meter
Narrow: SSG output
–117dBm (0.32µV) Wide:
(MOD: 1kHz, –117dBm (0.32µV)
Dev: ±1.5kHz) (MOD: 1kHz/±3kHz)
Narrow:
–117dBm (0.32µV)
(MOD: 1kHz,
Dev : ±1.5kHz)
Common Section
Specifications /
Item Test-
equipment
1. Setting 1) DC voltage: 13.6V
2) SSG standard modulation
[Wide] MOD: 1kHz, DEV: 3kHz
[Narrow] MOD: 1kHz, DEV: 1.5kHz
2. LCD 1) Adj item: [CNTR] 1) Adj item: [Panel Adjust the LCD After replacing the
contrast Adjust: [✳✳✳] [LCD Contrast] tuning contrast by looking. LCD align contrast.
Press [ ] key to store Press [Apply] mode]
the adjustment value. button to store the [ ],[ ]
adjustment value.
[PC test
3. Receive 1) Adj item: [RAST] 1) Adj item: mode] The sub LCD display 3.0V±0.1V
Assist Adjust: [✳✳✳] [Receive Assist] [ ],[ ] and [V] indicator
2) Adj item: [L RAST]→ 2) Adj item: [Low], on the PC window [PC test mode]
[L’ RAST]→[C RAST]→ [Low’], [Center], shows VCO lock Press [Apply All]
[H’ RAST]→[H RAST] [High’], [High] voltage. Change the button to store the
Adjust: [✳✳✳] Press [Apply All] adjustment value adjustment value
Press [ ] key to store button to store the to get VCO lock after all adjustment
the adjustment value. adjustment value. voltage within the point was adjusted.
limit of the speci-
Transmit 1) Adj item: [TAST] 1) Adj item: fied voltage.
Assist Adjust: [✳✳✳] [Transmit Assist]
2) Adj item: [L TAST]→ 2) Adj item: [Low], Note:
[L’ TAST]→[C TAST]→ [Low’], [Center], Confirm the VCO
[H’ TAST]→[H TAST] [High’], [High] lock voltage approxi-
Adjust: [✳✳✳] PTT: Press mately 3 seconds
PTT : ON [Transmit] button. after the adjustment
Press [ ] key to store Press [Apply All] value is changed.
the adjustment value. button to store the
adjustment value.
4. RTC 1) Adj item: [RTC] 1) Adj item: [RTC [ ] [Panel tuning mode] Adjustment of the
oscillation Adjust: [✳✳✳] (Real-time clock)] Press [ ] key. After transceiver’s inter-
frequency automatic adjust- nal clock.
adjust ment adjusted value
is displayed on LCD.
Press [ ] key to
store the adjust-
ment value.
[PC test mode]
Press [Start] button
of “Auto Tuning”.
Press [Apply] button
to store the adjust-
ment value after the
automatic adjust-
ment was finished.
51
NX-700/700H
ADJUSTMENT
Specifications /
Item Test-
equipment
5. Frequency * The Frequency 1) Adj item: SSG ANT [ ] [PC test mode] [PC test mode]
adjust adjustment can be [Frequency] Press [Start] button “IF20” value =
performed only in 2) CH-Sig: 1-1 of “Auto Tuning”. Within 0±12 digits.
PC test mode. SSG output : Press [Apply] button The value of “IF20”
–20dBm (CW (with- to store the adjust- will become around
out modulation)) ment value after the “0” after the adjust-
Caution: automatic adjustment was finished.
Perform the frequency ment was finished. Frequency is adjust-
adjustment under the ed under receiving
following conditions. condition with SSG.
• Temperature range
of +23˚C to +27˚C
(+73.4˚F to +80.6˚F).
(The temperature
is displayed on the
Frequency adjustment
screen of the KPG-
111D and the LCD of
the transceiver.)
• Use an accuracy of
0.003ppm for the
SSG. (Use a standard
oscillator if necessary.)
Transmitter Section
Specifications /
Item Test-
equipment
1. High 1) Adj item: [HILMT] 1) Adj item: [High Trans- Power ANT [Panel 33.0W K ±3.0W
Transmit Adjust: [✳✳✳✳] mit Power Limit] meter tuning 53.0W HK
Power 2) Adj item: 2) Adj item: [Low], Ammeter mode] [PC test mode]
Limit [L HILMT]→ [Low’], [Center], [ ],[ ] Press [Apply All]
adjust [L’ HILMT]→ [High’], [High] button to store the
[C HILMT]→ PTT: Press [PC test adjustment value
[H’ HILMT]→ [Transmit] button. mode] after all adjustment
[H HILMT] Press [Apply All] [ ],[ ] point was adjusted.
Adjust: [✳✳✳✳] button to store the
PTT: ON adjustment value. CAUTION!
Press [ ] key to store Do not attempt to
the adjustment value. adjust the transceiv-
er’s transmit output
power beyond its
specifications.
If the transceiver
is adjusted beyond
the specifications, it
may cause deterio-
ration of the parts
reliability and the
output power may
be lowered sud-
denly and unstable.
The transceiver may
be also extremely
hot.
52
NX-700/700H
ADJUSTMENT
Specifications /
Item Test-
equipment
2. Low 1) Adj item: [LOLMT] 1) Adj item: [Low Trans- Power ANT [Panel 15.0W K ±1.0W
Transmit Adjust: [✳✳✳✳] mit Power Limit] meter tuning 25.0W HK
Power 2) Adj item: 2) Adj item: [Low], Ammeter mode] [PC test mode]
Limit [L LOLMT]→ [Low’], [Center], [ ],[ ] Press [Apply All]
adjust [L’ LOLMT]→ [High’], [High] button to store the
[C LOLMT]→ PTT: Press [PC test adjustment value
[H’ LOLMT]→ [Transmit] button. mode] after all adjustment
[H LOLMT] Press [Apply All] [ ],[ ] point was adjusted.
Adjust: [✳✳✳✳] button to store the
PTT: ON adjustment value. CAUTION!
Press [ ] key to store Do not attempt to
the adjustment value. adjust the transceiv-
er’s transmit output
power beyond its
specifications.
If the transceiver
is adjusted beyond
the specifications, it
may cause deterio-
ration of the parts
reliability and the
output power may
be lowered sud-
denly and unstable.
The transceiver may
be also extremely
hot.
3. High 1) Adj item: [HIPWR] 1) Adj item: [High 30.0W K ±1.0W

Transmit Adjust: [✳✳✳✳] Transmit Power] 50.0W HK 9.0A or less K
Power 2) Adj item: 2) Adj item: [Low], 13.0A or less HK
adjust [L HIPWR]→ [Low’], [Center],
[L’ HIPWR]→ [High’], [High] [PC test mode]
[C HIPWR]→ PTT: Press Press [Apply All]
[H’ HIPWR]→ [Transmit] button. button to store the
[H HIPWR] Press [Apply All] adjustment value
Adjust: [✳✳✳✳] button to store the after all adjustment
PTT: ON adjustment value. point was adjusted.
Press [ ] key to store
the adjustment value.
4. Low 1) Adj item: [LOPWR] 1) Adj item: [Low 5.0W K ±0.5W K,

Transmit Adjust: [✳✳✳✳] Transmit Power] 10.0W HK ±1.0W HK
Power 2) Adj item: 2) Adj item: [Low], 5.0A or less K
adjust [L LOPWR]→ [Low’], [Center], 8.0A or less HK
[L’ LOPWR]→ [High’], [High]
[C LOPWR]→ PTT: Press [PC test mode]
[H’ LOPWR]→ [Transmit] button. Press [Apply All]
[H LOPWR] Press [Apply All] button to store the
Adjust: [✳✳✳✳] button to store the adjustment value
PTT: ON adjustment value. after all adjustment
Press [ ] key to store point was adjusted.
53
NX-700/700H
ADJUSTMENT
Specifications /
Item Test-
equipment
5. Balance 1) Adj item: [BAL] 1) Adj item: [Balance] Deviation ANT [Panel The Deviation of 2kHz Tone deviation
adjust *2 Adjust: [✳✳✳] Deviation meter meter tuning 20Hz frequency is is within ±1.0% of
Deviation meter LPF : 3kHz Oscillo- mode] fixed. Change the 20Hz tone devia-
LPF: 3kHz HPF : OFF scope [ ],[ ] 2kHz adjustment tion.
HPF: OFF 2) Adj item: [Low], value to become
2) Adj item: [L BAL]→ [Low’], [Center], [PC test the same deviation [PC test mode]
[L’ BAL]→[C BAL]→ [High’], [High] mode] of 20Hz within the Press [Apply All]
[H’ BAL]→[H BAL] PTT: Press [ ],[ ] specified range. button to store the
Adjust: [✳✳✳] [Transmit] button. adjustment value
PTT: ON Press [Apply All] after all adjustment
Press [ ] key to store button to store the point was adjusted.
the adjustment value. adjustment value.
Sub LCD: [2kHz Sine Wave
Tone frequency Check box]: Check
[ ] key: Press while while transmitting
transmitting to change change to 2kHz.
20Hz and 2kHz.
*2: Refer to the “Necessary Deviation adjustment item for each signaling and mode” table on page 57.
Balance adjustment is common with the adjustment of all signaling deviation.
6. Maximum 1) Adj item: [Nn NDEV] 1) Adj item: [Maximum Deviation ANT [Panel 3056Hz ±50Hz
Deviation Adjust: [✳✳✳✳] Deviation (NXDN meter tuning
(NXDN) Deviation meter Narrow)] Oscilloscope mode] [PC test mode]
adjust *3 LPF: 3kHz Deviation meter [ ],[ ] Press [Apply All]
HPF: OFF LPF: 3kHz button to store the
[Narrow] 2) Adj item: HPF: OFF [PC test adjustment value
[NnL NDEV]→ 2) Adj item: [Low], mode] after all adjustment
[NnL’ NDEV]→ [Low’], [Center], [ ],[ ] point was adjusted.
[NnC NDEV]→ [High’], [High]
[NnH’ NDEV]→ PTT: Press
[NnH NDEV] [Transmit] button.
Adjust: [✳✳✳✳] Press [Apply All]
PTT: ON button to store the
Press [ ] key to store adjustment value.
[Very 1) Adj item: [Nv NDEV] 1) Adj item: [Maximum 1337Hz ±50Hz
Narrow] Adjust: [✳✳✳✳] Deviation (NXDN
2) Adj item: Very Narrow)] [PC test mode]
[NvL NDEV]→ 2) Adj item: [Low], Press [Apply All]
[NvL’ NDEV]→ [Low’], [Center], button to store the
[NvC NDEV]→ [High’], [High] adjustment value
[NvH’ NDEV]→ PTT: Press after all adjustment
[NvH NDEV] [Transmit] button. point was adjusted.
Adjust: [✳✳✳✳] Press [Apply All]
PTT: ON button to store the
Press [ ] key to store adjustment value.
7. Maximum 1) Adj item: [An ADEV] 1) Adj item: [Maximum Write the same ±50Hz
Deviation Adjust: [✳✳✳✳] Deviation (Analog adjustment value of
(Analog) Deviation meter Narrow)] “NXDN Deviation [PC test mode]
adjust *3 LPF: 15kHz Deviation meter [Narrow]” for each Press [Apply All]
HPF: OFF LPF: 15kHz adjustment point. button to store the
[Narrow] 2) Adj item: HPF: OFF Transmit at each adjustment value
[AnL ADEV]→ 2) Adj item: [Low], adjustment point and after all adjustment
[AnL’ ADEV]→ [Low’], [Center], check that the Analog point was adjusted.
[AnC ADEV]→ [High’], [High] deviation is between
[AnH’ ADEV]→ PTT: Press 2050Hz and 2150Hz.
[AnH ADEV] [Transmit] button. Deviation meter
Adjust: [✳✳✳✳] Press [Apply All] LPF: 15kHz
PTT: ON button to store the HPF: OFF
Press [ ] key to store adjustment value. [Panel tuning mode]
the adjustment value. PTT: ON
[PC test mode]
PTT: Press
[Transmit] button
54
NX-700/700H
ADJUSTMENT
Specifications /
Item Test-
equipment
[Wide] 1) Adj item: [Aw ADEV] 1) Adj item: [Maximum Deviation ANT [Panel Write the same 4150~4250Hz
Adjust: [✳✳✳✳] Deviation (Analog meter tuning adjustment value of
2) Adj item: Wide)] Oscilloscope mode] “NXDN Deviation [PC test mode]
[AwL ADEV]→ 2) Adj item: [Low], [ ],[ ] [Narrow]” for each Press [Apply All]
[AwL’ ADEV]→ [Low’], [Center], adjustment point. button to store the
[AwC ADEV]→ [High’], [High] [PC test Transmit at each adjustment value
[NvH’ NDEV]→ PTT: Press mode] adjustment point and after all adjustment
[NvH NDEV] [Transmit] button. [ ],[ ] check that the Analog point was adjusted.
Adjust: [✳✳✳✳] Press [Apply All] deviation is between
PTT: ON button to store the 4150Hz and 4250Hz.
Press [ ] key to store adjustment value. Deviation meter
the adjustment value. LPF: 15kHz
HPF: OFF
[Panel tuning mode]
PTT: ON
[PC test mode]
PTT: Press
[Transmit] button
Analog deviation adjustment (Narrow/Wide) is common with the adjustment of all analog signaling.
8. QT 1) Adj item: [An QT] 1) Adj item: [QT Deviation ANT [Panel Write the value as 0.30~0.40kHz
Deviation Adjust: [✳✳✳✳] Deviation (Narrow)] meter tuning followings.
adjust *4 Deviation meter Deviation meter Oscilloscope mode] 513 (Reference
LPF: 3kHz LPF: 3kHz [ ],[ ] value)
[Narrow] HPF: OFF HPF: OFF
PTT: ON PTT: Press [PC test
Press [ ] key to store [Transmit] button. mode]
the adjustment value. Press [Apply] [ ],[ ]
button to store the
adjustment value.
[Wide] 1) Adj item: [Aw QT] 1) Adj item: [QT 0.70~0.80kHz

Adjust: [✳✳✳✳] Deviation (Wide)]
PTT: ON PTT: Press
Press [ ] key to store [Transmit] button.
the adjustment value. Press [Apply]
button to store the
adjustment value.
9. DQT 1) Adj item: [An DQT] 1) Adj item: [DQT Write the value as 0.30~0.40kHz
Deviation Adjust: [✳✳✳✳] Deviation (Narrow)] followings.
adjust *4 Deviation meter Deviation meter 430 (Reference
LPF: 3kHz LPF: 3kHz value)
PTT: ON PTT: Press
button to store the
adjustment value.
[Wide] 1) Adj item: [Aw DQT] 1) Adj item: [DQT 0.70~0.80kHz

PTT: ON PTT: Press
button to store the
adjustment value.
55
NX-700/700H
ADJUSTMENT
Specifications /
Item Test-
equipment
10. LTR 1) Adj item: [An LTR] 1) Adj item: [LTR Deviation ANT [Panel Write the value as 0.65~0.85kHz
Deviation Adjust: [✳✳✳✳] Deviation (Narrow)] meter tuning followings.
adjust *4 Deviation meter Deviation meter Oscilloscope mode] 465 (Reference
LPF: 3kHz LPF: 3kHz [ ],[ ] value)
PTT: ON PTT: Press [PC test
Press [ ] key to store [Transmit] button. mode]
the adjustment value. Press [Apply] [ ],[ ]
button to store the
adjustment value.
[Wide] 1) Adj item: [Aw LTR] 1) Adj item: [LTR 0.90~1.10kHz
PTT: ON PTT: Press
button to store the
adjustment value.
11. DTMF 1) Adj item: [An DTMF] 1) Adj item: [DTMF Write the value as 1.40~1.60kHz
PTT: ON PTT: Press
button to store the
adjustment value.
[Wide] 1) Adj item: [Aw DTMF] 1) Adj item: [DTMF 2.90~3.10kHz
PTT: ON PTT: Press
button to store the
adjustment value.
12. Single 1) Adj item: [An TONE] 1) Adj item: [Single Tone Write the value as 1.40~1.60kHz
Tone Adjust: [✳✳✳✳] Deviation (Narrow)] followings.
Deviation Deviation meter Deviation meter 513 (Reference
(2TONE LPF: 15kHz LPF: 15kHz value)
deviation HPF: OFF HPF: OFF
adjust) PTT: ON PTT: Press
adjust *4 Press [ ] key to store [Transmit] button.
[Narrow] button to store the
adjustment value.
[Wide] 1) Adj item: [Aw TONE] 1) Adj item: [Single 2.90~3.10kHz
Adjust: [✳✳✳✳] Tone Deviation (Wide)]
PTT: ON PTT: Press
button to store the
adjustment value.
13. MSK 1) Adj item: [An MSK] 1) Adj item: [MSK Write the value as 1.40~1.60kHz
PTT: ON PTT: Press
button to store the
adjustment value.
56
NX-700/700H
ADJUSTMENT
Specifications /
Item Test-
equipment
[Wide] 1) Adj item: [Aw MSK] 1) Adj item: [MSK Deviation ANT [Panel Write the value as 2.90~3.10kHz
Adjust: [✳✳✳✳] Deviation (Wide)] meter tuning followings.
PTT: ON PTT: Press Oscilloscope mode] 513 (Reference
Press [ ] key to store [Transmit] button. [ ],[ ] value)
button to store the [PC test
adjustment value. mode]
14. CWID 1) Adj item: [Nv CWID] 1) Adj item: [CWID [ ],[ ] Write the value as 1.00~1.20kHz
Deviation Adjust: [✳✳✳✳] Deviation] followings.
[Very HPF: OFF HPF: OFF
Narrow] PTT: ON PTT: Press
button to store the
adjustment value.
■ Necessary Deviation adjustment for each signaling and mode

The following shows the necessary adjustment items for each signaling deviation. Please read the following table like the following example. In the
case of the signaling “QT (Wide)”, this signaling is composed of three elements [Balance, Maximum Deviation (Analog Wide) and QT Deviation (Wide)].
Please adjust Balance and Maximum Deviation (Analog Wide) before adjusting QT Deviation (Wide).
Necessary adjustment and order
Mode Signaling
Wide Narrow Very Narrow
Step1. Balance adjust Step1. Balance adjust
Audio -
Step2. Maximum Deviation (Analog Wide) Step2. Maximum Deviation (Analog Narrow)
QT Step2. Maximum Deviation (Analog Wide) Step2. Maximum Deviation (Analog Narrow) -
Step3. QT Deviation (Wide) Step3. QT Deviation (Narrow)
DQT Step2. Maximum Deviation (Analog Wide) Step2. Maximum Deviation (Analog Narrow) -
Step3. DQT Deviation (Wide) Step3. DQT Deviation (Narrow)
LTR Step2. Maximum Deviation (Analog Wide) Step2. Maximum Deviation (Analog Narrow) -
Analog Step3. LTR Deviation (Wide) Step3. LTR Deviation (Narrow)
DTMF Step2. Maximum Deviation (Analog Wide) Step2. Maximum Deviation (Analog Narrow) -
Step3. DTMF Deviation (Wide) Step3. DTMF Deviation (Narrow)
Step1. Balance adjust
Step1. Balance adjust
Step2. Maximum Deviation (Analog Wide)
2TONE Step2. Maximum Deviation (Analog Narrow) -
Step3. Single Tone Deviation (Analog
Step3. Single Tone Deviation (Analog Wide)
Wide)
MSK
Step2. Maximum Deviation (Analog Wide) Step2. Maximum Deviation (Analog Narrow) -
(FleetSync)
Step3. MSK Deviation (Analog Wide) Step3. MSK Deviation (Analog Wide)
Audio -
Step2. Maximum Deviation (NSDN Narrow) Step2. Maximum Deviation (NXDN Very Narrow)
NXDN Step1. Balance adjust
CEID - - Step2. Maximum Deviation (Analog Narrow)
Step3. CWID Deviation (NXDN Very Narrow)
Balance is common with all the above deviation adjustments. If Balance (Transmitter Section5) has already adjusted, please skip Step1 and adjust from Step2.
Maximum Deviation (Analog Wide/Narrow) is common with all the analog signaling deviations and CWID Deviation (NXDN Very Narrow). If Balance and
Maximum Deviation (Analog Wide/Narrow) (Transmitter Section7) have already adjusted, please skip Step2 and adjust from Step3.
57
NX-700/700H
ADJUSTMENT
Receiver Section
Specifications /
Item Test-
equipment
1. AF level [Panel test mode] 1) Test Channel SSG ANT [Panel Volume Up/Down 2.83V±0.3V
setting 1) CH-Sig: 1-1 Channel: 1 DVM Ext.SP tuning knob to obtain
SSG output: Test Signaling AF VTVM connec- mode] 2.83V AF output.
–47dBm (1mV) Mode: Analog Dummy tor [ ],[ ] (2.0W @ 4Ω load)
(MOD: 1kHz, Signaling: 1 load (4Ω)
Dev: ±1.5kHz) SSG output: [PC test
–47dBm (1mV) mode]
(MOD: 1kHz, [ ],[ ]
Dev: ±1.5kHz) (Volume
Button in
PC test
mode
screen)
2. Sensitivity 1 1) Adj item: [SENS1] 1) Adj item: [Panel Write the value as Variable-Capacitor
Adjust Adjust: [✳✳✳] [Sensitivity 1] tuning followings Tune voltage is
(BPF adjust) 2) Adj item: 2) Adj item: [Low], mode] [L SENS1] / [Low] adjusted.
[L SENS1]→ [Low’], [Center], [ ],[ ] : 110 (Output voltage ad-
[L’ SENS1]→ [High’], [High] [L’ SENS1] / [Low’] justment of IC206)
[C SENS1]→ Press [Apply All] [PC test : 145
[C SENS1] / [Center]
[H’ SENS1]→ button to store the mode]
: 180
[H SENS1] adjustment value. [ ],[ ]
[H’ SENS1] / [High’]
Adjust: [✳✳✳] : 180
Press [ ] key to store [H SENS1] / [High]
the adjustment value. : 180
3. Sensitivity 2 1) Adj item: [SENS2] 1) Adj item: Write the value as Variable-Capacitor
Adjust Adjust: [✳✳✳] [Sensitivity 2] followings Tune voltage is
(BPF adjust) 2) Adj item: 2) Adj item: [Low], [L SENS2] / [Low] adjusted.
[L SENS2]→ [Low’], [Center], : 70 (Output voltage ad-
[L’ SENS2]→ [High’], [High] [L’ SENS2] / [Low’] justment of IC205)
[C SENS2]→ Press [Apply All] : 87
[C SENS2] / [Center]
[H’ SENS2]→ button to store the
: 105
[H SENS2] adjustment value.
[H’ SENS2] / [High’]
Adjust: [✳✳✳] : 135
Press [ ] key to store [H SENS2] / [High]
the adjustment value. : 185
4. RSSI 1) Adj item: [An RRSSI] 1) Adj item: [RSSI SSG [Panel test mode]
reference Adjust: [✳✳✳] Reference (Narrow)] AF VTVM After input signal
adjust *5 2) Adj item: 2) Adj item: [Low], Oscilloscope from SSG, press
[AnL RRSSI]→ [Low’], [Center], Distortion [ ] key to store the
[Analog [AnL’ RRSSI]→ [High’], [High] meter adjustment value.
Narrow] [AnC RRSSI]→ SSG output: 12dB Dummy
[AnH’ RRSSI]→ SINAD level –3dB load [PC test mode]
[AnH RRSSI] (MOD: 1kHz, After input signal
SSG output: 12dB Dev: ±1.5kHz) from SSG, press
SINAD level –3dB [Apply] button to
(MOD: 1kHz, store the adjust-
Dev: ±1.5kHz) ment value.
[Analog 1) Adj item: [Aw RRSSI] 1) Adj item: [RSSI
Wide] Adjust: [✳✳✳] Reference (Wide)]
2) Adj item: 2) Adj item: [Low],
[AwL RRSSI]→ [Low’], [Center],
[AwL’ RRSSI]→ [High’], [High]
[AwC RRSSI]→ SSG output: 12dB
[AwH’ RRSSI]→ SINAD level –3dB
[AwH RRSSI] (MOD: 1kHz,
SSG output: 12dB Dev: ±3kHz)
SINAD level –3dB
(MOD: 1kHz,
Dev: ±3kHz)
58
NX-700/700H
ADJUSTMENT
Specifications /
Item Test-
equipment
[NXDN 1) Adj item: [Nv RRSSI] 1) Adj item: [RSSI Ref- SSG ANT [Panel [Panel test mode] Adjust with the ana-
Very Adjust: [✳✳✳] erence (Very Narrow)] AF VTVM Ext.SP tuning After input signal log signal.
Narrow] 2) Adj item: 2) Adj item: [Low], Oscilloscope connec- mode] from SSG, press
[NvL RRSSI]→ [Low’], [Center], Distortion tor [ ],[ ] [ ] key to store the
[NvL’ RRSSI]→ [High’], [High] meter adjustment value.
[NvC RRSSI]→ SSG output: 12dB Dummy [PC test
[NvH’ RRSSI]→ SINAD level –3dB load mode] [PC test mode]
[NvH RRSSI] (MOD: 1kHz, [ ],[ ] After input signal
SSG output: 12dB Dev: ±1.5kHz) from SSG, press
SINAD level –3dB [Apply] button to
*5: Because “RSSI reference adjust” of NXDN Narrow is adjusted by adjusting “RSSI reference adjust [Analog Narrow]”, it is not necessary to
adjust “RSSI reference adjust” of NXDN Narrow.
5. Open 1) Adj item: [An SQL] 1) Adj item: [Open SSG ANT [Panel test mode] “Open Squelch”
Squelch Adjust: [✳✳✳] Squelch (Narrow)] AF VTVM Ext.SP After input signal will not be adjusted
adjust *6 2) Adj item: 2) Adj item: [Low], Oscillo- connec- from SSG, press correctly if MOD
(Squelch [AnL SQL]→ [Low’], [Center], scope tor [ ] key to store the and Deviation are
level 5 [AnL’ SQL]→ [High’], [High] Distortion adjustment value. wrong.
adjust) [AnC SQL]→ SSG output: 12dB meter
[AnH’ SQL]→ SINAD level +1dB Dummy [PC test mode]
[Analog [AnH SQL] (MOD: 1kHz, load After input signal
Narrow] SSG output: 12dB Dev: ±1.5kHz) from SSG, press
SINAD level +1dB [Apply] button to
[Analog 1) Adj item: [Aw SQL] 1) Adj item: [Open

Wide] Adjust: [✳✳✳] Squelch (Wide)]
[AwL SQL]→ [Low’], [Center],
[AwL’ SQL]→ [High’], [High]
[AwC SQL]→ SSG output: 12dB
[AwH’ SQL]→ SINAD level +1dB
[AwH SQL (MOD: 1kHz,
SINAD level +1dB
(MOD: 1kHz,
Dev: ±3kHz)
[NXDN 1) Adj item: [Nv SQL] 1) Adj item: [Open Adjust with the ana-
Very Adjust: [✳✳✳] Squelch (Very Narrow)] log signal.
Narrow] 2) Adj item: 2) Adj item: [Low], This item is ad-
[NvL SQL]→ [Low’], [Center], justed under the
[NvL’ SQL]→ [High’], [High] condition that MOD
[NvC SQL]→ SSG output: 12dB is “non” due to the
[NvH’ SQL]→ SINAD level –2dB circuit configura-
[NvH SQL] (MOD: non) tion.
SSG output: 12dB
SINAD level –2dB
(MOD: non)
*6: Because “Squelch (Open) adjust” of NXDN Narrow is adjusted by adjusting “Squelch (Open) adjust [Analog Narrow]”, it is not necessary to
adjust “Squelch (Open) adjust” of NXDN Narrow.
59
NX-700/700H
ADJUSTMENT
Specifications /
Item Test-
equipment
6. Low RSSI 1) Adj item: [An LRSSI] 1) Adj item: [Low SSG ANT [Panel test mode]
at –118dBm Adjust: [✳✳✳] RSSI (Narrow)] Ext.SP After input signal
adjust *7 2) Adj item: 2) Adj item: [Low], connec- from SSG, press
[AnL LRSSI]→ [Low’], [Center], tor [ ] key to store the
[Analog [AnL’ LRSSI]→ [High’], [High] adjustment value.
Narrow] [AnC LRSSI]→ SSG output:
[AnH’ LRSSI]→ –118dBm (0.28µV) [PC test mode]
[AnH LRSSI] (MOD: 1kHz, After input signal
SSG output: Dev: ±1.5kHz) from SSG, press
–118dBm (0.28µV) [Apply] button to
[Analog 1) Adj item: [Aw LRSSI] 1) Adj item: [Low

Wide] Adjust: [✳✳✳] RSSI (Wide)]
[AwL LRSSI]→ [Low’], [Center],
[AwL’ LRSSI]→ [High’], [High]
[AwC LRSSI]→ SSG output:
[AwH’ LRSSI]→ –118dBm (0.28µV)
[AwH LRSSI] (MOD: 1kHz,
SSG output: Dev: ±3kHz)
–118dBm (0.28µV)
(MOD: 1kHz,
Dev: ±3kHz)
[NXDN 1) Adj item: [Nv LRSSI] 1) Adj item: [Low Adjust with the ana-
Very Adjust: [✳✳✳] RSSI (Very Narrow)] log signal.
Narrow] 2) Adj item: 2) Adj item: [Low],
[NvL LRSSI]→ [Low’], [Center],
[NvL’ LRSSI]→ [High’], [High]
[NvC LRSSI]→ SSG output:
[NvH’ LRSSI]→ –118dBm (0.28µV)
[NvH LRSSI] (MOD: 1kHz,
SSG output: Dev: ±1.5kHz)
–118dBm (0.28µV)
(MOD: 1kHz,
Dev: ±1.5kHz)
*7: Because “RSSI at –118dBm adjust” of NXDN Narrow is adjusted by adjusting “RSSI at –118dBm adjust [Analog Narrow]”, it is not necessary to
adjust “RSSI at –118dBm adjust” of NXDN Narrow.
7. High RSSI 1) Adj item: [An HRSSI] 1) Adj item: [High SSG ANT [Panel test mode]
at –80dBm Adjust: [✳✳✳] RSSI (Narrow)] Ext.SP After input signal
adjust *8 2) Adj item: 2) Adj item: [Low], connec- from SSG, press
[AnL HRSSI]→ [Low’], [Center], tor [ ] key to store the
[Analog [AnL’ HRSSI]→ [High’], [High] adjustment value.
Narrow] [AnC HRSSI]→ SSG output:
[AnH’ HRSSI]→ –80dBm (22.4µV) [PC test mode]
[AnH HRSSI] (MOD: 1kHz, After input signal
SSG output: Dev: ±1.5kHz) from SSG, press
60
NX-700/700H
ADJUSTMENT
Specifications /
Item Test-
equipment
[Analog 1) Adj item: [Aw HRSSI] 1) Adj item: [High SSG ANT [Panel test mode]
Wide] Adjust: [✳✳✳] RSSI (Wide)] Ext.SP After input signal
2) Adj item: 2) Adj item: [Low], connec- from SSG, press
[AwL HRSSI]→ [Low’], [Center], tor [ ] key to store the
[AwL’ HRSSI]→ [High’], [High] adjustment value.
[AwC HRSSI]→ SSG output:
[AwH’ HRSSI]→ –80dBm (22.4µV) [PC test mode]
[AwH HRSSI] (MOD: 1kHz, After input signal
SSG output: Dev: ±3kHz) from SSG, press
Dev: ±3kHz) ment value.
[NXDN 1) Adj item: [Nv HRSSI] 1) Adj item: [High Adjust with the ana-
Very Adjust: [✳✳✳] RSSI (Very Narrow)] log signal.
Narrow] 2) Adj item: 2) Adj item: [Low],
[NvL HRSSI]→ [Low’], [Center],
[NvL’ HRSSI]→ [High’], [High]
[NvC HRSSI]→ SSG output:
[NvH’ HRSSI]→ –80dBm (22.4µV)
[NvH HRSSI] (MOD: 1kHz,
SSG output: Dev: ±1.5kHz)
–80dBm (22.4µV)
(MOD: 1kHz,
Dev: ±1.5kHz)
*8: Because “RSSI at –80dBm adjust” of NXDN Narrow is adjusted by adjusting “RSSI at –80dBm adjust [Analog Narrow]”, it is not necessary to
adjust “RSSI at –80dBm adjust” of NXDN Narrow.
8. Tight 1) Adj item: [An SQLT] 1) Adj item: [Tight SSG ANT [Panel test mode]
Squelch Adjust: [✳✳✳] Squelch (Narrow)] AF VTVM Ext.SP After input signal
adjust 2) Adj item: 2) Adj item: [Low], Oscillo- connec- from SSG, press
(Squelch [AnL SQLT]→ [Low’], [Center], scope tor [ ] key to store the
level 9 [AnL’ SQLT]→ [High’], [High] Distortion adjustment value.
adjust) [AnC SQLT]→ SSG output: 12dB meter
[AnH’ SQLT]→ SINAD level +6dB Dummy [PC test mode]
[Analog [AnH SQLT] (MOD: 1kHz, load After input signal
Narrow] SSG output: 12dB Dev: ±1.5kHz) from SSG, press
SINAD level +6dB [Apply] button to
[Analog 1) Adj item: [Aw SQLT] 1) Adj item: [Tight

Wide] Adjust: [✳✳✳] Squelch (Wide)]
[AwL SQLT]→ [Low’], [Center],
[AwL’ SQLT]→ [High’], [High]
[AwC SQLT]→ SSG output: 12dB
[AwH’ SQLT]→ SINAD level +6dB
[AwH SQLT (MOD: 1kHz,
SINAD level +6dB
(MOD: 1kHz,
Dev: ±3kHz)
61
NX-700/700H
TERMINAL FUNCTION
Display unit (X54-3640-10) Pin No. Name Function
Pin No. Name Function J901 (MIC jack)
CN901 (to TX-RX unit A/2 CN597) 1 BLC MIC key backlight control.
1~6 SPO Speaker input. Power output of switched power supply.
2 SB
7 GND Ground. DC13.6V±15%, 200mA typ.
8 80C 8V input. 3 E Ground.
9,10 SB Power input of switched power supply. 4 PTT/TXD PTT: PTT input, TXD:S erial data output.
11 NC Non connection. 5 ME MIC ground.
12 /PSW Detection signal output of power switch. 6 MIC MIC signal input.
13,14 GND Ground. HOOK: Hook detection,

7 HOOK/RXD
RXD: Serial data input.
15 MIC MIC signal output.
8 DM MIC data detection.
16 ME MIC ground.
17 GND Ground.
18 AFO RX filtered AF signal input. TX-RX unit (X57-7380-XX) (A/2)
19 /PRST Display MCU reset signal input. Pin No. Name Function
20~23 GND Ground. CN595 (to Option board)
24 SHIFT Control signal input of Beat-shift function. 1 OPT1
25 NC Non connection. 2 OPT3
26 5C 5V output. 3 26P_RD
27 TXD Serial data signal input. 4 26P_TD
28 RXD Serial data signal output. 5 NC
29,30 GND Ground. 6 OPT4
CN902 (to internal speaker) 7 OPT10
1 GND Ground. 8 OPT5
2 SPO Speaker output. 9 DGND
CN905 (to LCD ASSY) 10 AGND
1 V5 LCD Drive voltage output. 11 AI
2 V4 LCD Drive voltage output. 12 AO
3 V3 LCD Drive voltage output. 13 AGND Refer to “CN595 26-pin connector specifi-
4 V2 LCD Drive voltage output. 14 5V cation”.
5 V1 LCD Drive voltage output. 15 OPT9

6 Vdd LCD Driver DC power supply. 16 DTI
7 Vss LCD Driver Ground. 17 OPT8
8 Vdd LCD Driver DC power supply. 18 OPT11
9 D7 LCD Driver data output. 19 OPT7
11 D5 LCD Driver data output. 21 TXO
12 D4 LCD Driver data output. 22 RXEO
13 D3 LCD Driver data output. 23 RXEI
14 D2 LCD Driver data output. 24 TXI
16 D0 LCD Driver data output. 26 POW
17 /WR LCD Driver WR signal output. CN597 (to Display Unit CN901)
18 A0 LCD Driver address output. 1,2 GND Ground
19 /RES LCD Driver Reset signal output. 3 RXD Serial data signal input
20 /CS LCD Driver Chip-select signal output. 4 TXD Serial data signal output
62
NX-700/700H
TERMINAL FUNCTION
Pin No. Name Function Pin No. Name Function
5 NC No connection 3 SPO Speaker input.
6 50C 5V output. 4 PA Control signal output of PA function.
7 SHIFT Control signal output of Beat-shift function 5 HOR Control signal output of Horn alert function.
8~11 GND Ground 6 GND Ground.
12 /PRST Display MCU reset signal output CN403
13 AFO RX filtered AF signal output 1 IGN Ignition sense input.
14 GND Ground 2 GND Ground.
15 ME MIC ground
16 MIC MIC signal input TX-RX unit (X57-7380-XX) (B/2)
17,18 GND Ground Pin No. Name Function
19 /PSW Detection signal input of power switch CN901 (to TX-RX unit A/2 CN600)
20 NC No connection 1 AUXIO6 AUX input/output 6.
21,22 SB Power output of switched power supply 2 AUXIO7 AUX input/output 7.
23 80C 8V output 3 AUXIO1 AUX input/output 1.
24 GND Ground 4 AUXIO2 AUX input/output 2.
25~30 SPO Speaker output 5 RXD2 Serial data output 2.
CN600 (to TX-RX unit B/2 CN901) 6 AUXIO3 AUX input/output 3.
1 NC No connection. 7 TXD2 Serial data input 2.
2~7 SB Power output of switched power supply. 8 AUXIO4 AUX input/output 4.
8 AFO RX filtered AF signal output. 9 AUXIO8 AUX input/output 8.
9 DI Data signal input. 10 AUXIO5 AUX input/output 5.
10 50C 5V output. 11 AUXIO9 AUX input/output 9.
11 GND Ground. 12 AUXO1 AUX input 1.
12 DEO RX Detected signal output. 13 TXD0 Serial data input 0.
13 MI2 External MIC signal input. 14 AUXO2 AUX input 2.
14 ME MIC ground. 15 RXD0 Serial data output 0.
15 GND Ground. 16 GND Ground.
16 RXD0 Serial data input 0. 17 ME MIC ground.
17 AUXO2 AUX output 2. 18 MI2 External MIC signal output.
18 TXD0 Serial data output 0. 19 DEO RX Detected signal input.
19 AUXO1 AUX output 1. 20 GND Ground.
20 AUXIO9 AUX input/output 9. 21 50C 5V input.
21 AUXIO5 AUX input/output 5. 22 DI Data signal output.
22 AUXIO8 AUX input/output 8. 23 AFO RX filtered AF signal input.
23 AUXIO4 AUX input/output 4. 24 SB Power input of switched power supply.
24 TXD2 Serial data output 2. 25 SB Power input of switched power supply.
26 RXD2 Serial data input 2. 27 SB Power input of switched power supply.
29 AUXIO7 AUX input/output 7. 30 NC No connection.
30 AUXIO6 AUX input/output 6. J901 (ACC. D-Sub 25pin)
CN705 1 NC
Refer to “D-sub 25-pin connector specifica-
1 SB Power output of switched power supply. 2 RXD1
tion”.
2 SPI Speaker output. 3 TXD1
63
NX-700/700H
TERMINAL FUNCTION
Pin No. Name Function Pin No. Name Function
4 AUXIO9 19 DEO
5 DI 20 AUXIO5
6 MI2 21 AUXIO4
7 GND 22 AUXIO3
tion”.
8 AUXIO8 23 AUXIO2
9 TXD2 24 AUXIO1
10 RXD2 25 ME
11 GND
tion”.
12 AUXIO7 Solder Land
13 AUXIO6 Name Description
14 SB to GPS receiver
15 AUXO2 DGND Ground
16 AUXO1 RXD2 Data input
17 AFO 5V_2 5V power supply
18 GND
Solder Pad Interface Description

Rating and Condition
Pin Name I/O SignalType
Parameter Min Typ Max Unit
VIH 2.7 - 3.5 V
VIL –0.3 - 0.7 V
OPT1 I/O Digital/CMOS Out/CMOS In with Interrupt
VOH (Io=–2mA) 2.8 - 3.4 V
VOL (Io=2mA) - - 0.7 V
VIH 2.7 - 3.5 V
VIL –0.3 - 0.7 V
VOH (Io=–2mA) 2.8 - 3.4 V
VOL (Io=2mA) - - 0.7 V
VIH 2.7 - 3.5 V
26P_RD I Digital/CMOS In with Interruput VIL –0.3 - 0.7 V
Baud Rate - - 19200 bps
VOH (Io=–2mA) 2.8 - 3.4 V
26P_TD O Digital/CMOS Out VOL (Io=2mA) - - 0.7 V
VIH 2.7 - 3.5 V
VIL –0.3 - 0.7 V
OPT4 I/O Digital/CMOS Out/CMOS In
VOH (Io=–2mA) 2.8 - 3.4 V
VOL (Io=2mA) - - 0.7 V
Output Amplitude - 0.28 - Vp-p
OPT10 Coupling Capacitor 0.1 uF

O Digital/Analog
(USEL) Allowable Load 100 - - kΩ
Pull Down Registor - 470 - kΩ
64
NX-700/700H
TERMINAL FUNCTION
VIH 2.7 - 3.5 V
VIL –0.3 - 0.7 V
VOH (Io=–2mA) 2.8 - 3.4 V
VOL (Io=2mA) - - 0.7 V
DGND - -
AGND - -
Input Level - 3.3 - Vp-p
OPT9
I Analog Coupling Capacitor - 0.01 - uF
(STON)
Input Impedance 22 - - kΩ
DTI I Analog Coupling Capacitor - 0.1 - uF
VIH 2.7 - 3.5 V
VIL –0.3 - 0.7 V
VOH (Io=–2mA) 2.8 - 3.4 V
VOL (Io=2mA) - - 0.7 V
VIH 2.7 - 3.5 V
VIL –0.3 - 0.7 V
VOH (Io=–2mA) 2.8 - 3.4 V
VOL (Io=2mA) - - 0.7 V
VIH 2.7 - 3.5 V
VIL –0.3 - 0.7 V
VOH (Io=–2mA) 2.8 - 3.4 V
VOL (Io=2mA) - - 0.7 V
VIH 2.7 - 3.5 V
VIL –0.3 - 0.7 V
VOH (Io=–2mA) 2.8 - 3.4 V
VOL (Io=2mA) - - 0.7 V
Output Level - 130 - mVp-p
TXO O Analog Coupling Capacitor - 0.1 - uF
Allowable Load 100 - - kΩ
RXEO O Analog Coupling Capacitor - 0.1 - uF
allowable Load 100 - - kΩ
Input Level - 640 - mVp-p
RXEI I Analog Coupling Capacitor 0.1 uF
TXI I Analog Coupling Capacitor 0.1 uF
VIH 2.7 - 3.5 V
VIL –0.3 - 0.7 V
VOH (Io=–2mA) 2.8 - 3.4 V
VOL (Io=2mA) - - 0.7 V
65
NX-700/700H
TERMINAL FUNCTION
Ouput Voltage (Iout=100mA) 7.6 8.0 8.4 V
POW - Power
Output Current - - 100 mA
VIH 2.7 - 25 V
RXD2 I Digital/CMOS In with Interrupt VIL –10 - 0.6 V
VOH(Io=-8mA) 4.3 - 5.2 V
TXD2 O Digital/CMOS Out VOL(Io=8mA) - - 0.5
Output Voltage (Iout=100mA) 4.65 5.0 5.2 V
5V_2 - Power
Output Voltage (Iout=100mA) 3.2 3.3 3.4 V
33V - Power
CN595 26-pin connector specification (Rating/Condition)

Pin No. Pin Name I/O Signal Type
VIH 2.7 - 3.5 V
VIL –0.3 - 0.7 V
1 OPT1 I/O Digital/CMOS Out/CMOS Inwith Interrupt
VOH (Io=–2mA) 2.8 - 3.4 V
VOL (Io=2mA) - - 0.7 V
VIH 2.7 - 3.5 V
VIL –0.3 - 0.7 V
VOH (Io=–2mA) 2.8 - 3.4 V
VOL (Io=2mA) - - 0.7 V
VIH 2.7 - 3.5 V
3 26P_RD I Digital/CMOS Inwith Interrupt VIL –0.3 - 0.7 V
Baud Rate 19200 bps
VOH (Io=–2mA) 2.8 - 3.4 V
4 26P_TD O Digital/CMOS Out VOL (Io=2mA) - - 0.7 V
Baud Rate 19200 bps
5 NC - -
VIH 2.7 - 3.5 V
VIL –0.3 - 0.7 V
6 OPT4 I/O Digital/CMOS Out/CMOS In
VOH (Io=–2mA) 2.8 - 3.4 V
VOL (Io=2mA) - - 0.7 V
Output Amplitude - 0.28 - Vp-p
OPT10 Coupling Capacitor 0.1 uF

7 O Digital/Analog
(USEL) Allowable Load 100 - - kΩ
Pull_Down Register - 470 - kΩ
VIH 2.7 - 3.5 V
VIL –0.3 - 0.7 V
VOH (Io=–2mA) 2.8 - 3.4 V
VOL (Io=2mA) - - 0.7 V
66
NX-700/700H
TERMINAL FUNCTION
9 DGND - -
10 AGND - -
Input Amplitude - 0.5 - Vp-p
11 AI - Analog Coupling Capacitor - 0.1 - uF
Output Amplitude - 50.0 - mVp-p
12 AO O Analog Coupling Capacitor - 0.1 - uF
13 AGND - -
Output Voltage
4.7 5.0 5.1 V
14 5V - Power (Iout=200mA)
OPT9
15 I Analog Coupling Capacitor - 0.01 - uF
(STON)
16 DTI I Analog Coupling Capacitor - 0.1 - uF
VIH 2.7 - 3.5 V
VIL –0.3 - 0.7 V
VOH (Io=–2mA) 2.8 - 3.4 V
VOL (Io=2mA) - - 0.7 V
VIH 2.7 - 3.5 V
VIL –0.3 - 0.7 V
VOH (Io=–2mA) 2.8 - 3.4 V
VOL (Io=2mA) - - 0.7 V
VIH 2.7 - 3.5 V
VIL –0.3 - 0.7 V
VOH (Io=–2mA) 2.8 - 3.4 V
VOL (Io=2mA) - - 0.7 V
VIH 2.7 - 3.5 V
VIL –0.3 - 0.7 V
VOH (Io=–2mA) 2.8 - 3.4 V
VOL (Io=2mA) - - 0.7 V
21 TXO O Analog Coupling Capacitor - 0.1 - uF
22 RXEO O Analog Coupling Capacitor - 0.1 - uF
23 RXEI I Analog Coupling Capacitor 0.1 uF
67
NX-700/700H
TERMINAL FUNCTION
24 TXI I Analog Coupling Capacitor 0.1 uF
VIH 2.7 - 3.5 V
VIL –0.3 - 0.7 V
VOH (Io=–2mA) 2.8 - 3.4 V
VOL (Io=2mA) - - 0.7 V
Output Voltage
7.6 8.0 8.4 V
26 POW - Power (Iout=100mA)
CN595 26-pin connector specification (Function)

Pin No. Pin Name Device I/O Connection Description/Function
[COR]
Conv/LTR
L: Not activity receiving
H: Activity receiving
[TOR]
ANI board O Aux Input Conv/LTR
1 OPT1 L: Not activity receiving
H: Activity receiving
[LOK]
Conv
L: TX Complete
VGS-1 I BUSY BUSY indication
ANI board I KEY TX requirement input
2 OPT3
VGS-1 I PLAY PLAY indication
ANI board - - -
3 26P_RD
VGS-1 I SO Serial data input
ANI board - - -
4 26P_TD
VGS-1 O SI Serial data output
5 NC - - - -
ANI board O PTT PTT signal output
6 OPT4
VGS-1 O EN Enable signal output
OPT10 ANI board - - -

7
(USEL) VGS-1 O USEL UART speed select signal output
ANI board O Emergency Emergency signal output
8 OPT5
VGS-1 O RST Reset signal output
ANI board - A- GND
9 DGND
VGS-1 - DGND DGND
ANI board - A- GND
10 AGND
VGS-1 - AGND AGND
ANI board - - -
11 AI
VGS-1 I AO VGS Audio signal input
68
NX-700/700H
TERMINAL FUNCTION
Pin No. Pin Name Device I/O Connection Description/Function
ANI board - - -
12 AO
VGS-1 O AI VGS Audio signal output
ANI board - A- GND
13 AGND
VGS-1 - AGND AGND
ANI board - - Note: POW and 5V can not be used simultaneously.
14 5V
VGS-1 O 5C 5V power supply
OPT9 ANI board I Sidetone Side tone signal input

15
(STON) VGS-1 - - -
ANI board I Data out Data signal input
16 DTI
VGS-1 - - -
ANI board I Tone Control Speaker mute signal input
17 OPT8
VGS-1 - - -
ANI board O Man-Down Man-Down signal output
18 OPT11
VGS-1 - - -
ANI board I MIC Mute MIC mute signal input
19 OPT7
VGS-1 - - -
ANI board I Aux Output Emergency signal input
20 OPT2
VGS-1 - - -
ANI board - - -
21 TXO
VGS-1 - - -
ANI board - - -
22 RXEO
VGS-1 - - -
ANI board - - -
23 RXEI
VGS-1 - - -
ANI board - - -
24 TXI
VGS-1 - - -
ANI board - - -
25 OPT6
VGS-1 - - -
ANI board O A+ 8V power supply
26 POW
VGS-1 - - Note: POW and 5V can not be used simultaneously.
D-sub 25-pin connector specification

Pin No. Pin Name I/O A/D
1 NC (Non-connection) - - -
Input Voltage Range –30 30 V
Threshold Low 0.5 1.3 V
RXD1
2 Serial data input 1. I Digital Threshold High 1.75 2.6 V
RS-232C level.
Baud Rate 11520 bps
CL 100 pF
Voltage Swing (3kΩ Load) ±5 ±9 V
TXD1
3 Serial data output 1. O Digital Baud Rate 11520 bps
RS-232C level.
CL 100 pF
69
NX-700/700H
TERMINAL FUNCTION
VIH 4 - 5.2 V
AUXIO9 VIL –0.5 - 1 V

4 I/O Digital
AUX input/output 9. VOH (Io=–1.5mA) 4 - 5.2 V
VOL (Io=1.5mA) - - 1.1 V
DI Input Voltage range (STD Deviation) - 0.5 - Vp-p

5 I Analog
Data signal input. Freq Response (STD Dev.) 20~9600Hz –3 3 dB
Audio Level (STD Deviation) - 5 - mVrms
MI2
6 I Analog Allowable Freq 300 3000 Hz
External MIC input.
Input Impedance - 600 - Ω
7 GND (Ground) - GND
VIH 4 - 5.2 V

8 I/O Digital
VOL (Io=1.5mA) - - 1.1 V
VOH (Io=–1.5mA) 3.7 - 5.2 V
TXD2
9 Serial data output 2. O Digital VOL (Io=1.5mA) - - 1.1 V
TTL level.
CL 100 pF
VIH 2.8 - 5.2 V
RXD2
10 Serial data input 2. I Digital VIL - - 0.65 V
TTL level.
CL 100 pF
VIH 4 - 5.2 V
AUXIO7/
BER_DATA VIL –0.5 - 1 V
12 I/O Digital
AUX input/output 7. VOH (Io=–1.5mA) 3.7 - 5.2 V
BER data input.
VOL (Io=1.5mA) - - 1.1 V
VIH 4 - 5.2 V
AUXIO6/
BER_CLK VIL –0.5 - 1 V
13 I/O Digital
AUX input/output 6. VOH (Io=–1.5mA) 3.7 - 5.2 V
BER CLK input.
VOL (Io=1.5mA) - - 1.1 V
SB Voltage This parameter depends on Battery Voltage
14 Power output after - Power
power switch. Supply Current - - 2 A
The type of this port is open collector.
AUXO2
15 O Digital VOL 0.4 V
AUX output 2.
IOL –500 mA
The type of this port is open collector.
AUXO1
16 O Digital VOL 0.4 V
AUX output 1.
IOL –500 mA
Output Level 0.7 Vp-p
AFO Coupling Capacitor 0.1 uF
17 RX filtered audio O Analog
output. allowable Load 100 - - kΩ
allowable freq 300 3000 Hz
70
NX-700/700H
TERMINAL FUNCTION
Output Level - 0.28 - Vp-p
Coupling Capacitor - 4.7 - uF
DEO allowable Load 47 - - kΩ
19 Detected signal O Analog
output. Freq. Response (STD Dev) Wide; 20~4800Hz –6 1 dB
Freq. Response (STD Dev) Wide; 4800-7200Hz –24 1 dB
Freq. Response (STD Dev) Narrow; 20-4800Hz –15 1 dB
VIH 4 - 5.2 V

20 I/O Digital
VOL (Io=1.5mA) - - 1.1 V
VIH 4 - 5.2 V

21 I/O Digital
VOL (Io=1.5mA) - - 1.1 V
VIH 4 - 5.2 V

22 I/O Digital
VOL (Io=1.5mA) - - 1.1 V
VIH 4 - 5.2 V

23 I/O Digital
VOL (Io=1.5mA) - - 1.1 V
VIH 4 - 5.2 V

24 I/O Digital
VOL (Io=1.5mA) - - 1.1 V
25 ME (Mic ground) - Analog This is GND port for Microphone.
71
A B C D E F G H I J
1 NX-700/700H PC BOARD
DISPLAY UNIT (X54-3640-10) Component side view (J79-0157-29)
2
C956
C955
C963
C949
C950
C951
C952
C953
C954
R974
R968
R969
R970
R982
R967
R971
R972
R973
R962
LEFT
UP
PSW
3 D929
D916
D915
D922
D914
R925
C922
4
D912
R923 C924
R924 C925
R922
D919
D920
D921
R945
R921
C923
5 D935
DM/KVL
HK/RXD
MIC LEFT
ME DOWN
J901
PTT/TXD
6 E
SB
BLC/AFO
D927
D931
D932
PF1 PF2
8
DISPLAY UNIT (X54-3640-10) Foil side view (J79-0157-29)
D913
Q902
R907 IC905 CP909

R963
D910
D904
L905
R952
R926
4 3
Q901
5 4 R935 C927
C913
C948 CP917
G
S
D
IC901 5 1
9 R902 1 8 C957
R909
BLC/AFO 8 1
R912
R911
C906 C907
C926 R934 IC907

Q904
R997
R927
SB C912 L902 C917

4 5
4 3
R906
C911
E
R916 R917
C928 C921
IC908 100
1
R996
C967
C946 R946
R947 R944
R936
C905
L904
R915
C919
C920
PTT/TXD 5 1
4 3
5 1
Q908
D906
ME C910 L901
C929
C941
IC902
MIC R905 R914

R948
R918 R938 R939
R908
HK/RXD R913
10
D902
D901
D903
C918
DM/KVL R949
C908 C938
R901
IC911
X901
C909
Q910 C936
R919
C965
C947
GND 30
CN901 4 3
SPO 2
R950
C915
RXD
5C
SHIFT
GND
GND
AFO
ME
GND
/PSW
SB
8C
SPO
SPO
C940
IC903
R937
R942
/PRST
29 GND
GND
GND
GND
GND
GND
L908
TXD
SPO
SPO
SPO
11
MIC
C939
NC
NC
SB
C916 5 1 R943
Q909
GND
1
C942
D907 1 5 25
R958
C930
C903 C914 L903 LDM 26 5

IC904
C964
R957
R930
3 4
Q911
G
S
R940 TH901
CP912
D
R955 CP907 CP908 CP910

R929 R941
R977
R978
R979
1 + C944
CN902
R953 4 3
12
R956
R954
R999
L906
C933
C945
R933
C934
2 5 4 IC909
/CS 20
C931 C932
IC906
V5 1
R965 5 1
V4
V3
V2
V1
VDD
VSS
VDD
D7
D6
D5
D4
D3
D2
D1
D0
/WR
AO
/RES
Q905
Q906
8 1
+ C943
+ C935 CN905
R931 R932
13
72
14
J K L M N O P Q R S
PC BOARD NX-700/700H 1
DISPLAY UNIT (X54-3640-10) Component side view (J79-0157-29)

2
R988 R990 Ref. No. Address Ref. No. Address
Q913
1 6 R976 R989 R960 Q913 2K D924 5K
C963
R981
R991 C958
3 4 D908 4N D925 5N
R974
R982
R973
RIGHT
UP
D911 4M D926 3M
D936 D912 4H D927 6E 3
D914 3C D928 6K
D917
D918
D926
D915 3G D929 3D
D916 3H D930 5P
D917 3K D931 6I
D918 3L D932 6G 4
D908
D919 5H D933 6O
D911
R923 C924
D920 5G D934 6M
D923
D924
D925
R904
R920
D921 5I D935 5D
D922 3I D936 3P
D930 5
D923 5L
RIGHT
DOWN
6
Component side
D928
D933
D934
Layer 1
Layer 2
PF3 PF4
Layer 3
Layer 4 7
J79-0157-29
Foil side
DISPLAY UNIT (X54-3640-10) Foil side view (J79-0157-29) 8

J79-0157-29
Ref. No. Address Ref. No. Address
IC901 9D Q905 12C
R966
R964 IC902 10E Q906 12C
C962
R900
IC903 11F Q908 10E 9

R992
IC904 11G Q909 11B
76
48
25
75 IC905 9F Q910 10E

IC906 12F Q911 12B
IC907 9F D901 10C
10
IC908 9F D902 10B
IC909 12G D903 10B
IC910 12K D904 9B
C961
IC913
IC911 10I D906 10D

IC912 13L D907 11D 11
IC913 11L D910 9E
51
50 Q901 9D D913 9C
Q902 9E D937 12L
CP912
CP910
Q904 9E
R979
24
12
1
11 10
/CS 20
D937
IC910
C966
R986 Component side

5 4 R928
IC912
20 1 8 1 L907
Layer 1
C959 R998 C960 Layer 2
Layer 3 13
Layer 4
Foil side
73
14
14
13
12
11
10
9
8
7
6
5
4
3
2
1
74
A
BATT CHK
R422 R426
Q405
R632
R633
Q411
R678
C618
3 4
1 5
R445
R415
R444
C435
C438
6 1
4 3
B
Q406
C825
CN405
D410
R413
IC513
C589
C588
D508
IC715
(DM) 1 IC512
GND R433
D504
RXD 4 3 D411
TXD
D512
C817 TTL
C592
C593
NC
R634
5C 5 1 R831
R842
R651
IC403
SHIFT/MODEL 6 GMD
C585 C584
GND
R674
R672
1 6 R671 F501
(LCDDO)
R644
R654
R658
R650
(LCDDI) D511
C590 C515
L522
R673 7
12
R670 R669
R523
C587
RST2(LCDCLK) 3 4
1
5
R506
HOR
J79-0129-29 A/2
(LCDCB)
13
6
AFO C586 R663 R668
GND
Q501
ME C527 R662 R667
MIC R661 IC517 R666 PA
CN597
GND R575
C
GND R660 R665

J701
CN705
19
24
R640
C583
18
PSW
EXT. SP
SPO
I
G
O
NC R659 R664 RS-232C
R630
SB
5 1
4 3
IC507
SB
D507
R648 R646 C596
D506
L506
8C C582 9 8 SPI
R578
R580
R583
GND
R690
SPO C595
8
5
SPO R576
C591
C581
SPO R641 1 SB
C614
SPO R579 1 8
IC514
SPO 20 19
1
4
R582 R639 IC516
SPO 30
R689
R642 CN403
R585 4 5
C615
IC518
C580
2
1
CN549
R586
NX-700/700H
C820
R826
C422
R637
D509
D510
2 1 R588 R638
D
R590 Q709
+
R652 5 4
R656 C612
R593 C807
C613
+
16 1 C429 C806
C534 IC515
R401
R595
R592
R589
R636
8 1
+
OPT10 C616 C473 R823 R403
C594 C406
C805
OPT11
BSC1 BSC0
AGND C432
DGND
C410
E
26P_RD
R534 C549 C551
FLDM
C557
C550
Q403
26P_TD
+
L511
C554
C555
C559
C560
C558 R922 C401
TXD2 CN401 CN402
+B GND
RXD2
C556 C548 C547 C552 L903
PC BOARD
L508
OPT1 R603
R684 C537
C538
C539
C540
C403
D404
F
R919
R918
OPT3
F401
L403
OPT4
L402
L401
OPT5
C419
C421
C545 C543
5V_1 C553 2 OPT3 OPT1 1
26P_TD 26P_RD C546 D405
C561
OPT4 C562
D408
DTI C563 OPT5 OPT10 L512 C427

OPT8 C566 GND C428
G
AO AI C565
C567 GND
CN595
L517
TXO C569 DTI OPT9 C568
C571 OPT11 OPT8 C570
OPT7 OPT2 OPT7 C572
C573 RXEO TXO
C575 TXI RXEI C574
OPT2 C576
C577 26 OPT6 25
C579 C578
OPT9
C449
C448
Component side view (J79-0129-29 A/2)
RXEO
H
L509
TXI
5 1
4 3
IC407
L510
RXEI
R123
R127
C137
C440
C439 R125
33V 5V_2 DGND

OPT6
1
R124 C135
TX-RX UNIT (X57-7380-XX) (A/2) -10: K -12: HK
POW
D102
I
R119 C126
+
C138
C139
R117
C119 R120
C133
C130
C127
C125
L106
R85 C26 R20 R9 C447 4 3 R115

R121
R15
R131
IC406 R116
CV
L35
C471
4 3
L32
R11
R417
4
1
5 1
R14 C20
C19
IC4 C29 R37 R36 R30 R21

R126
R25 C17 C450 C434

5 1 C27
IC101
R22
J
C452 C437
18
19
C25
C21 25 1
R34 R33 + C34
R52
R51
R49
+ C35
C28
5
8
C33 R38 IC3

+ C32
L31
C14
R23 C22
C132
C47 R48 R
C54 C
C5
D3 Q2 R130
J K L M N O P Q R S

Component side view (J79-0129-29 A/2)

R150 IC1 10L Q106 8K
IC2 9K Q201 10N
C188 IC3 9J Q202 10N 3
IC102
IC4 12J Q212 10O

IC5 11J Q403 2E
C182 IC101 7J Q405 9B
IC102 3K Q406 9B
C179 4
IC103 7K Q411 10B
C198
TH102
R161 IC201 10N Q501 11C
3 4
IC202 9O Q709 5D
IC203 10P D3 12J
IC205 7N D21 9K 5
C173 IC206 7O D102 5I
C167
L107 IC403 5B D207 10M
C174
L108 IC406 8J D208 9M
C151 +
L109
C165 IC407 12H D209 9M
IC507 10C D210 8M 6
C141
C145
C148
C149
TH101
C163
C124
R122
IC512 12B D404 6F
IC513 8B D405 6G
IC514 9D D408 5G
R140 R273
IC515 8D D410 10B
C157 C289 C298
R126 C132 7
R139
1 8 IC516 8D D411 10B

R284
R292
R288 R287
R286
R297 R296
R299
IC103
R143
C162
1 8
4 3
IC205
5 1
4 3
5 1
IC206
IC101
R132
R134 R921
R135 4 5 R145 IC517 9C D504 13B
R310
C356
4 5 R147 R156
R142
R144
IC518 7D D506 8C
R130
G
R138
C156
D C197
S
D210
Q105 R302
R562
Q106 IC715 4B D507 8C

C299 R285
C293 R291
C301
R565
C302
Q1 12K D508 8B
17
Q5 8
Q3 S
4 3 Q2 8J D509 9D
R26
C450 C434
C452 C437
D 6 1
R82 L221
G
1
Q3 8J D510 8D
C222
C194 C193
R84
R83
5
Q2
C296 R290
C357
C297
D R333
S Q5 8K D511 8C
C221
C229
L31 C195 G Q15 D209 C223

71 D21 R315
R353
C224 C212
C14 C295 C294

Q15 9K D512 9B
C190
32 13 L33 L1 1 24
R223 R227
C17
18
C232
R228
R210
R80
R216
11 12
R12
C16
19 R338
Q105 8K
L219
C19 C11 C8 9
R6
C218
IC3
C13
X1
IC202
C20 C351
R10 C219 C227 R334
C15
C21 25 1 7 C288 R283

1 6
3 4
IC2
R7
L223
6 C220 C233
D208 CD201 C226
C353 C352 R226
R331 R215
R21
R23 C22
C27
C25
C23
R18 C24
5 C7 Q212 R329 12 13 R232

C291 C290
R5
R239 R224
C6 R86 4 3
C28
C358
L34
C230
R218
R22 6 1 C225
C336
R225
R1 C3 L218 C202 C201

C12
R2
C1
R88 R3 C2
C5
R209
R330 C354
R25
+ C32
R328
R37 R36 R30
Q201
C355 5 4
R229 10
4 3
5 1
C213
C228 R219
C286 R282 IC203

R236
C235
IC1
R220
R31
C287
C214 Q202
+ C34 8 1
R231
C334
D207
R212 R211
R548
IC201
1 5
3 4
C237
R245
C244
C231
R4 C285 C284 CF203
+ C35
R222
C9
R221 RAGC
R29 IFDET
L217
C47 R48 R44 C31

R47
VAGC
C54 C46
C282
R35
R27 R28
R49 5 4 LO
R51 IC5 R276
R52 8 1
11
R274
R275
R278
C55
R352
BPF GND Component side
R342
Layer 1
C29
R248
C245
C37
Layer 2
R34 R33
C33 R38
C18
Q1 R17
4 3
5 1
IC4
D3
Layer 3
R13
R89
Layer 4 12
Layer 5
Layer 6
Foil side
13
75
14
A B C D E F G H I J
Foil side view (J79-0129-29 A/2)
Ref. No. Address Ref. No. Address Ref. No. Address

IC204 11F Q13 10I D14 11I
IC401 7M Q14 10I D15 11J L116
3 IC402 6N Q101 7I D16 11I
IC404 6P Q102 7J D18 11J
C184
C186
IC405 5N Q203 8E D19 9I
C178 R149 C183
L115
IC408 5M Q204 9D D20 9I
IC409 7N Q205 10D D101 9H D109
4
L114
IC410 12J Q208 10G D103 5F
C176
IC501 12P Q210 7G D104 6F
IC502 10Q Q401 3P D105 6E C177
D108
IC503 12Q Q402 4P D107 6D C175
CN511 CN513
R148
5 IC504 10N Q404 4P D108 5D

L113
CN517
IC505 10P Q407 5P D109 4D
C136
C134
IC506 13P Q408 5P D201 10E D103
IC508 10O Q409 7O D202 10F

L112
C171
L110
D104
IC509 9P Q410 7N D205 9H C169
R146
D107
6 IC510 12O Q412 6N D213 7E

L111
C158
C154
IC511 9O Q413 5P D215 7D
C172
D105
R137
R154
C170
C164
IC701 12M Q414 5P D216 7E C159

R141 C155
IC702 8N Q415 7O D217 7E
CN502 CN504 CN508 CN520
IC703 12L Q416 5N D218 7E D218 D213
7 IC704 10M Q417 12I D401 3O
C342
C311 R107 C105 E C
R105 Q101
C341
R304
R103 C104
C101
C103
C328
R101
C102
D216 R319 D217
R113 L102
Q102
IC705 12L Q701 12K D403 4P
C111 L101
R303 L229
R294
R102
R106
R104
R306 L222 R109 C109 B E
D215
C338
R341
C337
C Q210
L230
R340
R347
C316 R110
C112
IC706 8M Q702 11L D406 3P
C335
L220
C106
C116
R111
C308
R112
C304
R108
R322
C107
R339
C110
B
C329
IC707 12M Q703 12M D407 4N R305 C300
C315 R307 R301
IC708 8N Q704 7P D409 4N CN505 CN503
8 CN527
IC709 8O Q705 8P D412 5N
R202
L202 C207
L201 C216 C211 Q203

C206
C77
C217
IC710 11M Q706 8R D501 13O
C61
C49 C53
C48
L16
L204
L8
R61
R332
R46
R63
L206 C215 C210 R205 C208 L12
IC711 11L Q707 8R D502 13O R235 C66 C57
R346
R213 D20
C238
R234
D6
L205 C234 C348
C78
IC712 9L Q708 10L D503 9O
C62
C52
R79
L18
C239 C73 C68 R59 R39
R45 L7
R238 C71
C203
L20
IC713 11K Q710 5Q D702 11L
NARROW
9
R240
C44
CF202
D19
L36
R75 R76 C97
C69 C56
C65
Q204
C36 C45
L15
D101
Q6
R93 R
C242 R56
IC714 11L D5 9J D703 11L C96
R77 R78
C333 R327
R60
D5
C263
C261
L208 C240
C95
R74
R204 C204
C332 R314
L28
C93 R71 C92

R264
Q6 9I D6 9J D704 7O R243
R242
C359 R343
R207
D205
C264
R73
R72
C91
C94
L27
L207 R201 Q13 S
C90
R69
C98 D
Q7 9K D7 11I D705 8O C243
C89
R66
D202 R266 G
D201 Q14 R70
CN540
R244
R208
R265 Q12
R247
Q9 10I D8 11J D706 9L

Q205
Q208
R268 Q10
Q9
R325 C331
C205 R206
C266
R313 C330
R324 R203
R67 C38
D
C268
10
G
Q10 10J D11 11H D707 9M

C80 C79
C269
L211
CF201
C246
WIDE
G C85
D
S
L22
R267 R269 S
Q11 10K D12 11J
L23
CN510 C270
L26
C87 R65
C88
R64
L213
C84
C272 C81 C82

Q12 10J D13 11H C275 C72 C70
L215
L25
C283 R279
C64
C76 D18
CN543
C67
C280
R281
R277
R280
R256 R250
L17
C267
R320 L19
D13
D11
CN507
D15
D12
L212 D16
D14
11
C279
C252 R271 C42

C39
R91
L41 C41
C262
D7
C51
L13
R90
L10
L11
L14
R42
L2
Component side
L3
IC204 L40 C50 R43 C43 L4

1 6
C247
L209
L214
Layer 1 XF202 3 4
R257 R321
R261
Layer 2
R263
C260
R270
C276
C265
C259 C462 C460

L210
R441
R443 C461
R438
Layer 3
R450
5 4
C256 C464 IC410
12 Layer 4 R442 8 1 C459 +
Layer 5 C465
R436
3
1
C467
Q417
L406
Layer 6
4
5
C466
Foil side
13
76
14
J K L M N O P Q R S

Foil side view (J79-0129-29 A/2)
C809
C811 C810
R411
C417
R410 3
D406
D401 Q401
R404
C405
R402
D403
Q402
R408
R409
C475
C445 L405 G R825

C801 4
C446 +
C411
R407
Q404 D C802
C415
D409 D407
R828
Q710
R448
C468 S
C443 R430 1 6 Q414
R827
C804
C454 IC405
C441 Q413 C803
3 4
R431 L404
R423
C474
R424
Q408
R432
C431
C430
D412
5
IC408
4 3
5 1
Q407
R440
CN542
C463 R447
C136
C134
Q416
C456
4 3
6 1
R419 R418
3
1
C453
IC402
C425
R437
4
C409 C426 C433
O
C413 C424 6
I
+
R446
C436
IC404
Q412
R428
R429
R425 R420
R421
G C597
D
G
R449 S
Q410
NC/RSSI 1
520 SB
Q409 SB
R405 SB C611
C420 R406
SB
1 5
IC401
3 4
SB
4 3 7
C455 C442
SB
C451 C444
C118 L104 L105

AFO
DI/RTS
C610
E C IC409 Q415 50C C609
C120
C115 R114
C121 D704 Q704

R113 L102
Q102 GND
C123
C128
DEO
09 B E C122 5 1 R784 MI2 C608
C765
C750 ME
CN600
C117
L103
GND C607
C112
C762
C116
R111 RXD0
R112
C108 C744 AUXO2 C606
R804
TXD0
C766
R722 R716 C707 C729 R749 Q705 AUXO1 C605

C742 R753
1 8 R767 C751 AUXIO9/CTS

R724 R787
C721
C787
R813 C791
C794
1 8 IC708 AUXIO5 C604
C736
R748
R768
C763
4 5 AUXIO8
R789
R725 IC706 D705 AUXIO4 C603

4 5 R765 TXD2/AUXIO9
C715 R759 AUXIO3 C602
8
C782 R796 R793
RXD2/DI R815
C748 R766 C770 AUXIO2 C601 C793 R809
R745
AUXIO1
C757
R773
C600 R812
Q707
R739
R741
1 8 C773 AUXIO7/BER DT
R779
R786
C764
G
S
AUXIO6/BER CK 30
D
C706 IC709 G
C783 R797
C784 R798
C599
R816
5 4
C49 C53
C48 C815 R714 4 5 D

R705
C712
R774
L8
IC702 C598 S Q706

R46 R710 8 1 R731 R775 R801
C57 R57 D706 C816 R806 C795
C720
C701
C776
D6
R833
R835
R834
C777 R822
C52
R39 CN509 CN506

C75
R45 L7
C813
9
C44
12
R693
R544
L502
C518
R93 R92
56 C63 R685
R557
R558
R538
R539
R553
C516
R540
R541
R695
R696
C517
R554
R694
C790
C36 C45
D707
Q7
4
R574 R584
CN611
IC509
C732
L24
C83 IC712 IC511 R686

R733 R552
L503
R915 C536
C789 R821
X501
C86 R68
C529
4 3
5 1
C532 C531 R542

5
8
D503
4 3 R537
4 3
R62
R734
13
24
S Q11 R818 R536 R543

C90
R69
D IC704
R596 R594
6 1
R66
G C522 L905
CN516
Q708
C799
R820
5 1
Q12 IC508 R581 R533 C513
X502
R817 1 5
C714 R717
C710
C774 IC505 R532 R531

R836
10 1 6
R545 C521 L523
L521 R561
R726
C725
R730
3 4 R529
C528
R698
C514
C530
D
10
8
IC502
R802 R799
C785
R846
3 4 R567 R527
C85
R800 IC504 R516

L22
R795 R790 R560

R794
R572
S R805 R528
1
R803 R814 C779 C511

R697
L26
7 R65 R511
CN612
R512
R520
R780
C778
C767
C82 R810 C792 R792

C788
C509
R677
R629
R687
R688
R625
C621
C544
R624
C814
8
C542 +
8
C70 R791 R521

R819 C798
R785 C775
IC713
IC711
IC710
IC714
4 3 R507
R781
R525
R524
C76 D18 C769

CN512
5 1 C541
R701 R706
R569
R680
R616
R615
R617
R611
R612
R618
R620
R619
1
C761 R788
R807 R808 C507
C754
D15
D12
C512
C797 C796 C786 R783
C745 R764 R776
C749 C752 R777
R772 C753 R778
C768
R510
C508
R841
C503
R556
R501
C506
C505
C824
C504
Q702
R845
R770
11
R782
D8
C740 R577 R515 R514

R91
C51
L11
C741
R747
C738
R750
D703
R720
L4 R843 R771 R606
R43 C43
R727 C737
R751
C818
C718 C734
D702 R691
C747
C719 R755 R605

R769
G
1 8 D R763 IC510
C722
R729
S R692
IC705 Q703 C746
R760
4 5 R607
460 C716
C743
R758
R746
C711 C731 R752
R587
R438
R709
4
1
R721
R707
R761
IC707
R608
C724
C821 C502
R837
R756
TH701
R762
C458
C457
R610 C501 12
5
R838
IC501
IC503
C459 +
Q701
R503
D
L904 L501
G
S
C717 R738
R728
C726
R704 R708
R732
C735 R568
R703
R435 R434 R718 C723

R436
C730 R744
R591
R597
R623
R628
R627
R621
R622
R676
R602
R715 C533
R604
R614
C705 R740
C727
1 8
R713 R551
C702
L406 R712 IC703 R737

4 3
CN614
C535
C709 4 5 5 1 C708 R681 C520

C620
IC701 R683 1 4
R600
R601
R599
R598
R682
L518 L507 2 3 C523 R509 R504 R522
D501
D502
IC506
13
J79-0129-29 A/2
77
14
A B C D E F G H I J
TX-RX UNIT (X57-7380-XX) (B/2) -10: K -12: HK
Component side view (J79-0129-29 B/2)
2
R902
R903
R911
R912
C911
C912
R904
C913
R905
C914
R906
C916
R907
C917
R908
C918
C919
R909
C920
R910
C921
R913
C909
C910
C923
25 14
4
13 1
C905 C906 C904

Component side D906
D905
5
L902
L901
Layer 1
C901
C908
J79-0129-29 B/2 C915 C903
Layer 2 C902
Layer 3
NC/RSSI 30
AUXIO6/BER CK 1
AUXIO7/BER DT
AUXIO1
AUXIO2
RXD2/DI
AUXIO3
TXD2/AUXIO9
AUXIO4
AUXIO8
AUXIO5
AUXIO9/CTS
AUXO1
TXD0
AUXO2
RXD0
GND
ME
MI2
DEO
GND
50C
DI/RTS
AFO
SB
SB
SB
SB
SB
SB
Layer 4
Layer 5 Ref. No. Address
6
Layer 6 D905 5G
CN901
Foil side D906 5H
7 TX-RX UNIT (X57-7380-XX) (B/2) -10: K -12: HK

Foil side view (J79-0129-29 B/2) R901
R914
8
Q901
Q902
B
C
C
B
C
C
C907
C922
C
C
C
C
E
J79-0129-29 B/2 D910 D914
9 D909 D913
D901 D902 D903 D904 D907 D908 D911 D912
13 1
J901
25 14
10
Component side
Layer 1
Layer 2
Layer 3
11 Layer 4
Layer 5
Layer 6
Foil side
12
Q901 8G D904 9E D911 9F
Q902 8H D907 9E D912 9F
D901 9C D908 9E D913 9H
13 D902 9D D909 9G D914 9H
D903 9D D910 9G
78
14
IC102
RA30H1317M123 : K
RA60H13171123 : HK
26 PIN BOARD TO BOARD CONNECTOR

1 4
ANT
2
1
1
AI
26
TD
RD
NC
AO
R150
DTI
TXI
50C
80C
IGN
TXO
CN595
GND
GND
RXEI
GND
OPT1
OPT3
OPT4
OPT5
OPT9
OPT8
OPT7
OPT2
OPT6
RXEO
DGND
OPT11
CN705
OPT1O
CN403
1
SB
SPI
SPO
CN901 CN597 PA
30 1 HOR
GND GND
GND EXT SP
GND GND
6
RXD RXD
TXD TXD
CN902 5C 5C
2 NC NC CN401 +
SHIFT SHIFT
SPO 13.6V
GND GND
GND GND CN402 –
GND GND GND
1 GND GND CN901
PRST PRST CN600
INT SP 30 1
AFO AFO
GND GND AUXIO6 AUXIO6
ME ME AUXIO7 AUXIO7
DISPLAY UNIT TX-RX UNIT
MIC MIC AUXIO1 AUXIO1
X54-364 X57-738 A/2 AUXIO2 AUXIO2
GND GND
GND GND RXD2 RXD2
AUXIO3 AUXIO3 J901
PSW PSW
NC NC TXD2 TXD2 13 AUXIO6
SB SB AUXIO4 AUXIO4 25 ME
SB SB AUXIO8 AUXIO8 12 AUXIO7
AUXIO5 AUXIO5 24 AUXIO1
80C 80C 11 GND
GND GND AUXIO9 AUXIO9 23 AUXIO2
J901 SPO SPO AUXO1 AUXO1 10 RXD2
8 AUXIO3
DM SPO SPO TXD0 TXD0 22
9 TXD2
HK AUXO2 AUXO2 AUXIO4
MIC SPO SPO 21
ME SPO SPO RXD0 RXD0 8 AUXIO8
PTT 20 AUXIO5
SPO SPO GND GND GND
E 7
SB SPO SPO ME ME 19 DEO
BLC 1 30 MI2 MI2 6 MI2
1 18 GND
DEO DEO DI
5
GND GND 17 AFO
50C 50C 4 AUXIO9
/WR
/RES
/CS
V5
V4
V3
V2
V1
VDD
VSS
VDD
D7
D6
D5
D4
D3
D2
D1
D0
A0
1 20 16 AUXO1
INTERCONNECTION DIAGRAM
DI DI 3 TXD1
CN905 AFO AFO 15 AUXO2
SB SB 2 RXD1
14 SB
SB SB 1 NC
SB SB
SB SB
LCD SB SB
SB SB
NC NC TX-RX UNIT
1
/SCRST
/SCREQ
/SCSS
/SCWKUP
/SCBFS
DGND
DGND
SCTXD
SCSCK
SCRXD
SCBSY
SCTAM2
NC
SCTAM1
33M
SCMOSI
SCBCK
SCMISO
DGND
DGND
20
1
30 X57-738 B/2
1 5 1 3
CN549
20 PIN BOARD TO BOARD CONNECTOR

AUDIO IC 80C AVR
LA4425A NJM78M08FA-ZB
IC715 IC403
79
NX-700/700H
A B C D E
NX-700/700H
TX-RX UNIT (X57-738X-XX) (A/2)
SCHEMATIC DIAGRAM
1 (K) R : 13.57V (HK) R : 13.6V
T : 13.14V T : 12.57V
∗L401
L402
CN401 +B
L403 (K) (HK) IC405
C421 0.047u
C419 1000p
C427 470p
C428 100p
1000u25
22ZR-10D
LT1616ES6-PBF
F401
R : 13.57V R : 13.6V
DSA3A1
C401
C403
470p
5A
+
D405
D404
T : 13.14V T : 12.57V
4 3
L404 SHDN FB 5.01V
5 2
VIN GND
CN402 6 1 D409
SW BooST 50M
1SS388F
C454
470p
R430
120k
0.01u
C468
SURGE REVERSE
ABSORPTION PROTECTION
C430 4.7u
C431 4.7u
L405
R431
18k
22uH
IC405,D407,409
CRS02-Q
4.7u16
D407
C446
DC/DC
+
C475
C445
R432
10u
10u
Converter (50M)
22k
2 VOLTAGE
REGULATOR (33M)
R446
IC408
R448
4.99V 3.32V 33A

10
5.01V 3.29V
0
XC6204B332M Q416 3.29V

SSM6L05FU-F
1 5
VIN VOUT 33A_2
2 1.88V
C409 0.01u
C463
4
C426 0.01u
VSS
C441 0.01u
C456 0.01u
C413 1u
R437
50MC
XC6204B332P1
470k
1u
C424 1u
C443 1u
C453 1u
3 4
VIN
VoUT
Q412 5.00V
R449
CE NC
R428
3.89V 1.49V
22
10k
2SA1955A-F
IC402
R440
1k
VOLTAGE 0V DC SW 15M
VSS
D408 (50MC)
NC
REGULATOR (33A)
CE
1SS388F
R429
5
XC6205B152PRN
1SS301F
10k
D412
R447
DC SW (50IF)
47k
0V
1
VIN
2
3
VoUT
C442 0.01u
C455 0.01u
C451 2.2u
C444 1u
IC409
0.01u
C474
VSS
Q410
NC
REVERSE
CE
SSM3K15TE(F)
R421
CURRENT
470k
PREVENTION
1
2
3
DC SW
(OR 33M/SBC 2) (50MC)
3 1.57V
IC401
R405
VOLTAGE
270k
XC6108C23CMN REGULATOR (15M)

4 3
(K) VSEN VIN 33M
2
C420
R : 3.63V
0.1u
VSS Q405 SCTAM1

T : 3.51V 5 1 2SA1955A-F R415 3.31V
CD VoUT
3.3k
(HK) 33BU
DC SW 0V Q411
R : 3.64V 3.31V
1SS388F
(SCTAM1) 2SA1955A-F REVERSE
D411
T : 3.39V VOLTAGE DC SW CURRENT
DETECTOR (BINT) (33BU) DC SW
C435
C438
PREVENTION
10u
10u
(33BU)
R406
(33BU)
100k
Q406
/BINT
R444
UPA672T-A 2.97V
2.7k
R433
R422
1k
D410
R413
REVERSE
470k
0V 10k
CURRENT
1SS388F PREVENTION
R445
(BACK UP BATTERY)
CN405
R426
470k
47k
BATT CHK
/BINT
VOLTAGE
4 C415 REGULATOR (80C)
/RST
470p
SB
(K) (HK)
R : 13.56V R : 13.59V IC403 R : 8.01V
T : 13.13V T : 12.50V NJM78M08FA-ZB T : 8.01V
1 3
IN oUT 80C
Q404 GND
C411
470p
R407
R : 0V 1
47k
4.7u25
2SJ645
47u25
C422
C432
C473
C429
T : 7.93V
+
+
4.7u
0.1u
2 Q407
R402
DC SW 12A02CH
470
(SB) 80T
R418
10k
R423 DC SW (80T)
HSC119
4.7k
R409
R404
02DZ18F-X
68k
10k
D406
REVERSE
OVER DC
D401
CURRENT D406
SUPPLY 0V R : 8.01V
PREVENTION TXC
PROTECTION REVERSE T : 0V
Q413
R410
(K)
680k
D403 CURRENT
R : 1.77V PREVENTION DTC114EE
Q401 T : 1.71V Q408
DTC114EE 1SS416 (BLVL)
12A02CH
(HK) 80R
1.88V Q402 R : 1.77V
R419
0V DTC114EE T : 1.63V R : 8.01V

10k
R424 DC SW (80R)
5 4.7k T : 0V
C405
470p
DC SW
(SB) VOLTAGE Q414
R411
C417
470p
100k
SW (OVER DC REGULATOR (50C) R : 0V DTC114EE

SUPPLY IC404 T : 8.01V
PROTECTION) TA7805FQ 4.99V
R408
1 2
10k IN oUT 50C
GND R : 4.96V
C425 0.1u
C433 0.1u
Q409 T : 0V
10u10
12A02CH
C436
3
+
DC SW
(IGN) 50R
R420
47k
Q403 R425 DC SW (50R)

DTC114TE 4.7k
CN403
1 R401
R : 0V RXC
2 1M T : 4.96V
/OVRB
1000p
0.01u
Q415
C406
C410
R403
100k
BLVL
/IGN
SBC
DTC114EE
1
14.34V
IC406
L406 R450 TK71733S 3.30V
68u 0
SSM5H01TU-F
1 5
6 2
VIN VoUT 33C
R417
47k
Q417
GND
C434 1000p
DC SW
C437 0.22u
C450 0.01u
3 4
C464 22p
C452 1u
C471 1u
oN/oFF NP/VREF
R442
330k
0.22u
C447
VOLTAGE
REGULATOR (33C)
IC410
C465 1u
C466 1u
C467 1u
XC9101D09AKR
R434
33
1 8 IC407
EXT VSS XC6204B332M 3.28V
R436 2 7
7.84V LSEN VoUT/FB 1 5
R435 0 C462 VIN VOUT 33GPS
3 6 2
VIN CC/GAIN VSS
10 4 5 470p
C439 0.01u
3 4
R438
CE/SS CLK
150k
C440 1u
CE NC
R443
0.01u
C448
C449
22k
2.2u
4.7u16
C458
C459
C457
+
1u
1u
DC/DC VOLTAGE
C461
R441
C460
180p
CONVERTER
0.1u
REGULATOR (33GPS)
12k
(150C)
X57-738X-XX L401
0-10 K NO
0-12 HK L92-0179-05 150C 1
7
80
X57-738 (A/2) 1/16
F G H I J

SCHEMATIC DIAGRAM NX-700/700H
50C 50C
Q5
R79
EMD9 4.62V
56
R : 4.96V
470p
C77
470p
C48
T : 0.78V
R61
470p
R46
22k
22k
C73
R60
39n
L20
56k
RX
D6 C49 C57 L12 C66 D20 C68
HVC131 470p 2p 68n 470p HVC131 1000p
PLL FIN
C61
5.6n
5.6n
C53
22p
2.03V
18p
L16
T/R SW
L8
PLL FIN PLL FIN
T/R SW T/R SW Q6 2.30V
2SC5636
R : 0V
470p
C69
R56
330
Q2 T : 4.96V BUFFER AMP
DTA114YE 0.76V PLL FIN (PLL FIN)
PLL FIN
T/R SW T/R SW
C36 TX 0.77V
1000p D5 C45 C56 L15 C65 D19
PLL FIN
T/R SW HVC131 470p 3p 82n 470p HVC131
5.6n
5.6n
4.7k
C52
C62
39p
39p
R39
L18
L7
4.7k
R63
Q3
R45
R59
22k
22k
SSM3K15TE(F)
470k
R26
470p
470p
C78
C44
BYPASS
DIODE
D3
DA221
CV
C33
33p
FC-R : 5.52V IC4
RIPPLE FC-T : 4.91V R38
LMC7101BIM5
FILTER 10M
1 OUTPUT 5
0.1u
C37
14.34V Q1 13.72V V-
180k
R33
2SC5383-T111
R89 R17 2
V+
0 0 3 4 R85
R13
10k
14.30V
INPUT+ INPUT- 470k
R20 1k
100p
100p
C29
C26
BUFFER AMP
R34
47k
C18
1u (VCO TUNE)
ASSIST
/T_R
150C
50C
50C
2
50C
33C
L35
33C L33
R12
10
3.30V
L34
TEMP
SENSOR
C15 0.01u
R84
220
IC2 IC3
LM73CIMKX-0 3.31V C16 0.01u PLL IC
R918 4 3 3.17V
I2CCK SMBCLK VDD
5 2
0.01u
0
0.01u
C13
C6
ALERT GND
R18
12
11
10
R919 6 1
10
9
8
7
I2CDT SMBDAT ADDR

100
R5
0.01u
0
C194
OSCout
NC
OSC
2.7k
GND_OSC
VCC_SOC
/OSC_AC_GND
R83
4.98V
3.32V 13
LD/PS2 6
3.21V L31 14 CPout1
VCCcp 2 5
47p
VCCcp1
C7
X1 BUFFER AMP 15
(19.2MHz) C195 CPout2 4
0.01u L1 R6 R10 16 LD/PS1
VC VCC /FVco 3
Q15 /Fin
R21
4.7u 17
2SK1215-E(E) 4.7k 0 FVco 2 10
18 Fin
C190 VCCcp2 1
VCC
GND oUTPUT
100p
C14
VCC_digital
C11
0.01u
4.7k
39p
0V
R7
R86
0.64V
100
Max_out
19.2MHz
Mod_in
R80
18k
Clock
0.01u
C193
GND
Data
R82
18p
/CS
C8
1k
R23
1k
21
22
19
20
23
25
24
C22 100p
C23 100p
C25 100p
C24 0.1u
C27 0.1u
1.65V
R3 3.27V
L32 C19 100p
270k
3.32V C20 100p
100p
C5
100p
IC1
C17
100p
C21 100p
C28
HVC131
R88
LMC7101BIM5
0
D21
TCXO MOD 1 OUTPUT 5

V-
R11 10
R14 10
R15 10
33C 2
V+
3 4 R4 C9 R9
22k
R1
4.7k
INPUT+ INPUT- 220k 10u
R22
BUFFER AMP 1.65V
470p
0.1u
0.1u
47k
C12
22k
C1
C2
C3
(TCXO MODULATION)
R2
1u
TCXO_MOD
/PCS_RF
SDO1
SCK1
PLD
CV
2 2 2
1 1 1
81
X57-738 (A/2) 2/16
K L M N O
NX-700/700H SCHEMATIC DIAGRAM TX-RX UNIT (X57-738X-XX) (A/2)
D7,11,13,14 R : 3.46V
VCO T : 0V
C93
5p
FREQUENCY RX VCO R67
CONTROL Q9
2SK508NV(K52) 0.74V
150
1000p
R42 L3 C50 R90 D11 C67
C38
R70 C91 TX
0 10u 470p 0 33p
1SV282-F
1SV282-F
C79
150k 22p
8p
D13
1SV325F
C88
100p
C42
D7
100n
L27
17.5n
220n
220n
C72
3.83V
10p
L10
L19
L23
0.5p Q13
R64
270
2SC5636
1SV282-F
0.01u
C80
C84
220n
8p
D14
L13
3.3u
L25
1000p
L40
R71
C92
BUFFER AMP
100
(VCO)
470p
C39
D8,12,15,16 R : 0V
VCO T : 3.56V
FREQUENCY TX VCO R66
CONTROL Q10
L4 D12 2SK508NV(K52) 120
R43 C51 R91 C64
1000p
C89
0 10u 470p 0 56p
C81
1SV282-F
0.75p
1SV282-F
9p
C76
C87
1SV325F
D15
100p
C43
L2
D8
0.5p
35.5n
220n
220n
C70
L11
R65
270
L22
L17
7p
1SV278F
0.01u
C82
C85
D18
1SV282-F
8p
220n
3.3u
D16
L14
L26
L41 TX
R352 MODULATION
0 Q12
470p
C41
2SJ347F
R51
47k
C54 R49
1u 12k Q11 T/R SW
R52
(VCO)
68k
SSM6L05FU-F
R62
470p
VCO MOD
C90
R69
47k
C55
0.1u 470k
470p
C86
R68
IC5
C83
1k
L24
1u
TC75W51FK(F) 1.65V
CV R28 1 8 R92 R93
VDD
47k 7 0 0 R : 0.02V
100k
100p
R29
R27
68k
C31
1.65V 4.98V Q7 T : 3.31V

2
C46
47p
2SC5383-T111 4.21V
R25 R30 R36 R37 R35 3 6
100k
R44
0 0 390 10k 1k 4 5
470p
R : 3.01V VSS
R47
4.7k
C63
R57
RIPPLE
0
T : 3.00V FILTER
0.047u35
R31 10u20
0.15u35
+
C34
+
+
C32
C35
VCO MODULATION/
100k
R48
4.87V
BUFFER AMP (CV)
C75
10u
150
C47
1u
VCO_MOD
/T_R
50C
2 2
50R
50C
33C
50R
4.86V C215
R333
L206
R346 R202 L202 100p
1k
22k 47 560n
R205 R332 C210 L204 C217 C222 C223
0.01u
0.01u
C348
C207
330k 0 10p 47n 47p 0.01u 0.01u
C238
470p
R234
C208
220
R213 0.01u
4.35V
C211
C216
L201
100n
68p
68p
1k 0.66V Q203
C206
2SC5636
10p
0.01u
0.01u
C239
C357
R353
560n
R235
IF IC
L205
100
R227
47k
0
IC202
2nd LOCAL TK10931VTL-G
BUFFER AMP (X3)
1 24 R315 C234 R240
C212 OSC<B> RFin
2 0 0.01u 100k
0.1u
OSC<E> GND 23 0.74V
C232 0.1u
3
MIXo COMPo 22 RX
W : 2.89V R210 10 R228 100k
N : 0.29V
4
VCC 4.92V COMPi 21 Q204
R238
2SC3356(R23)
C224 R338 10k R223
R330
5 NAMPo 20
0
10
AMIFi 1st
0.1u C218 0.1u 270k C351 R334 IF AMP
4.97V
6
AMIFdecp NAMPi 19
R206
WIDE
22k
C203
C205
R203
0.1u
0.1u
1u 0
22k
R216 C227 0.1u R229

7
FMIFi AGC 18
CF201 W : 0.99V
L72-1017-05 0 C219 4.7u 8 17 22k
N : 1.09V
C202
0.1u
FMIFdecp1 AGCAMPo
C355
C354
0.1u
W : 0.99V
10u
C330 R313 IN oUT C331 C220 4.7u 9 16 R232

N : 1.09V CF SW FMIFdecp2 RFAGCo
0.1u 0 0.1u 10k
(W/N) C226 82p 10
D201 RSSIo 15
R325
R324
CD201 LIMo
1.8k
1.8k
DAN235E
D202 11 14
DAN235E QUADi AMSW
R218 12 13 R226
Narrow L79-1850-05 FMDETo AMDETo
10k 22k
R201
CF202
15k
SW CF SW R215
L72-1021-05
C233 1u
(W/N) (W/N)
C353 0.1u
C352 0.1u
R225 15k
R224 10k
2.7k
R208
C332 R314 IN oUT C333

15k
R329
2
5.6k
Q201 Q212
C221
0.01u
0.01u
C336
C225
C229
C230
0.1u
10u
10u
DTA114EE 0.1u 1.5k 0.1u EMD9

R327
3.3k
R204
R207
22k
22k
R331
47k
SW
1000p
C358
(W/N)
W : 0V
C204
0.1u
Q202 N : 3.29V
DTC144EE
C201
0.01u
VCO_MOD,/T_R
R328
1k
W : 3.27V
FM_DET
N : 0.02V
W_/N
2 2 2
1 1 1
82
X57-738 (A/2) 3/16
P Q R S T

BUFFER AMP R : 2.15V T/R R : 0V RF
(RF) T : 4.23V SW T : 4.94V PRE-DRIVE AMP
1.12V Q14 C98 R77 D101 C102 R103 C104 R107 C105 C109
2SC5636
TX C94 10p 0 HVC131 1000p 18 470p 180 470p 33p
RF DRIVE AMP
100n
2.2k
R75
L28
Q101
15p
L101
R102
R109
R104
4.7k
R78
82n
270
270
470
2SC5108(Y)F Q102 C118
0.96V 1.99V 2SC5455-A 56p TX
3.3k
R72
4.79V 1.22V
1000p
0.94V 7.70V
1000p
C95
R74
270
C96
1.76V
R114
L102
68n
330
R111
R112
2.7k
C106
C107
1.8k
470p
470p
R105
R106
R108
33k
100
10k
R73
10k
R101
C112
470p
R113
3.3k
22
HVC131
C115
470p
D205
T/R
SW
7.88V
R76
R : 2.82V
47
L36 T : 0V
50C
470p
C71
0.1u
C97
C116
470p
C111
470p
R110
22
R264
50R 4.7k
C101
0.01u
C103
470p
C261
0.01u
C263
470p
L103
C110
470p
C117
470p
C270
470p
R269
80T
47
4.60V
C108
4.7u
1000p
C268
L211
R267
100n
2.2k
R266
C264
470p
10k
R280
1k
0.87V C269 L213 L215 R279 C283
R343 C359 10p 47n 47n 47 470p
Q208
R281
0 470p
C272
C275
C280
R277
2SC5636
27p
18p
18p
120
120
2.03V
R265
3.3k
1000p
C266
R268
270
BUFFER AMP
(LOCAL)
50C
50R
80T
50R
50R
33A_2
C267
470p
L39-1498-05
L212
L208
R263 L210
R271
2.2k
47
C260
470p
C242
470p
R242
220
4.33V IC204
R274
1k
SPM5001
4.34V
L209 1 6 L214
L39-1498-05 G1 G2 L39-1498-05
2 5 C279 R276 RX
D1 S1
XF202 3 4 1000p 33
0.01u
C243
560n
R243
L207
58.05MHz D2 S2
100
R250 R320 R256 oUT IN R257 R321 R261 C259
R275
R278
180
180
1st 0.93V
0 0 180 3 6 0 0 0 0.01u C276
470p
0.01u
0.01u
C262
C265
MIXER
C252
C256
R270
1
2
5
4
RX C240 R247
1p
1p
68
0.01u 100k
C246
Q205 0.01u
2SC3356(R23)
1st 0.74V
R244
IF AMP
0
50R R209
10 33A_2
C213
0.1u
4.95V
R219
10k
5
4
R211
1k
MCP6021-E/OT
VIN-
VDD
0.01u
C228
IC201
R342
R248
470k
IC203
0
TC75W51FK(F)
1 VoUT
VIN+
VSS
R239 5 4
R220
47k
VSS
CF203 10k 6 3
2
1.39V 450kHz
0.01u
C245
C247
0.1u
1.39V C231 2
C235
R236
100k
47p
0.1u oUT IN R231 C334

C244
R212
R245
7
100k
47p
0
2.2k 0.1u
R221
R222
8 1
2.2k
BUFFER AMP
18k
VDD
(2nd IF DET)
W_/V
3.29V
0.01u
C237
C214
0.1u
BUFFER AMP
2
(RSSI/VAGC)
1
IF_DET
VAGC
RSSI
2 2
1 1
83
X57-738 (A/2) 4/16
U V W X Y

∗IC102
TH1
DRAINBIAS
ANTENNA
RFoUTPUT
GATEBIAS
RFINPUT
SWITCH
TH100
∗D103
C124
470p
R122
-t °
100k
3.3k
L407CDB
L112 L113 L114 L115
1
ANT
4
L104 D104 C165 5T 5T 5T 5T R150
33n ∗R124
L105 L407CDB 120p 0
∗C163
∗C171
∗C182
∗C173
∗C179
∗C186
∗C188
∗C167
∗C174
∗C177
R : 0V
L116
9.5T
∗R125
18p
C121 39n C135
9p
TX T : 1.60V
L110
10T
9p 470p
∗R123
∗R127
C122
C120
C123
C128
C137
22p
22p
33p
33p
18p
∗C169
∗C176
∗C184
C158
C154
1/4W
1/4W
470p
R137
R154
100p
240
240
POWER POWER POWER
DET DET DET
HSM88AS-E
HSM88AS-E
HSM88AS-E
L111
02DZ5.6F-X,Y
5T
C130 100p
C133 470p
C125 22p
C127 47p
D108
D109
D107
(K)
∗L107
4.7u25
∗C139
L108
L109
D102
FC-H : 3.80V
L106
+
FC-L : 2.80V
(HK) R : 0V
C155
C159
470p
100p
FC-H : 4.57V T : 0.8V
FC-L : 4.22V
PM DRAIN BIAS
∗R146
C170
C175
C183
470p
470p
470p
R148
R149
∗C138
150k
(K) (HK)
56k
3.3u
PROTECTION
FC-H : 13.12V FC-H : 12.38V FC-H : 2.04V
FC-L : 13.41V FC-L : 13.12V FC-L : 0.70V
L7091CER
+B
R141
C164
D105
18p
0
C141
C136
C145
C148
C149
C134
470p
470p
47u25
100p
100p
C151
R131
22p
47p
+
220
C172
C178
470p
470p
R147
8.2k
ANTENNA
SWITCH
80T
R140
R126 100k
100k
∗R115
TH2
AUTO AUTO
∗R139
POEWR CONTROL POEWR CONTROL
TH102
820p
R161
C198
470p
∗R120
-t °
100k
3.3k
IC101 IC103
∗R143
NJM2904V-ZB NJM2904V-ZB
∗C162
1 8 1 8
V+ V+
7 7
2 R134 2
3 6 ∗R132 100k 3 6
4 5 4 5 ∗R145
GND GND
∗R116
∗R135
SW
(RF PWER H/L)
C157
∗R142
R121
C132 Q105 470p

R130
100k
100k
DTC114EE
470p
Q106
1000p
SW
C197
R144
100k
(RF PWER H/L) 2SK1830F

R119 R138
10k
100k
R156
C119 R117
0
C156
100p
0
C126
470p
THP2
THP
470p
DSW
/H_L
MPL
APC
80T
MP
+B
2 2 2
150C
80R
HVC131
D215
1000p
C329
L220
1000p
C300
R339
R294
ANTENNA
220
0
5.43V SWITCH
1000p
C308
C304
270n
R306
L222
0.1u
4.7k
C328
R340
27p
0
RX C282 C287 L223 C297 R302 C335 C311 R304
0.88V
1000p 15p 150n 15p 0 150p 1000p 2.2k
1000p
1000p
1000p
1000p
C301
C290
C284
C294
VARI-CAP TUNE VARI-CAP TUNE 0.12V C315 R305 R322 R347 R341 C316
L221
L218
L219
1000p 0 0 0 0 18p
1000p
1000p
6T
6T
6T
C338
C337
Q210
1SV283F
1SV283F
1SV283F
1SV283F
L217
C291
R291
2SC3357-A
C302
C285
C295
D208
D209
D210
D207
R282
R283
R290
100k
100k
100k
100k
6T
12p
12p
12p
12p
LNA
L229
L230
4T
4T
1SV283F
1SV283F
D213
D216
D218
D217
R301
R307
12
1k
1000p
1000p
1000p
1000p
C286
C288
C296
C299
2
R303
R319
VARI-CAP VARI-CAP
100k
100k
TUNE TUNE
1000p
R286 R285
FL : 1.63V
C293
FC : 2.45V
FH : 4.36V
1000p
1000p
C341
C342
100k
R299
100k FL : 1.63V
IC205 IC206 FC : 2.45V
LMC7101BIM5 LMC7101BIM5 FH : 3.86V
14.33V 1 OUTPUT 5 14.33V 1 OUTPUT 5

V- V-
R296
R287
270k
270k
150C R273 2 2
V+ V+
0 3 4 3 4
C289
C298
0.1u
0.1u
INPUT+ INPUT- INPUT+ INPUT-

R288
R297
100k
100k
R292
R284
BUFFER AMP BUFFER AMP

10k
10k
(BPF TUNE) (BPF TUNE)

R921
C356
470p
R310
470k
0
RFAGC
TV1
TV2
2 2 2
1 1 1
X57-738X-XX D103 IC102 L107 R115 R116 R120 R123 R124 R125 R127 R132 R135 R139 R142 R143 R145 R146 C138 C139 C162 C163 C167 C169 C171 C173 C174 C176 C177 C179 C182 C184 C186 C188
0-10 K NO RA30H1317M123 NO 47k 22k 47k 270 39 39 270 330k 330k 100k 820k 82k 100k 82k 3.3u NO 820p NO 43p 2p 0.5p 47p NO 1.5p 0.5p 39p 22p 3p 0.5p 18p
0-12 HK L407CDB RA60H13171123 L92-0179-05 56k 18k 56k 220 47 47 220 100k 390k 120k 390k 100k 47k 120k NO 4.7u NO 9p 27p 6p 0.3p 22p 18p 5p 0.3p 36p 27p 6p 0.3p 15p
84
X57-738 (A/2) 5/16
Z AA AB AC AD

HD2
X2_CLKIN
15M
33M
3 3 3
4 4 4
5 5 5
/HRDY
/DRST
/HINT
L502
L503
4 /BER_EN
3
1000p
R841
C508
R510
R515
470k
100k
1.48V 3.31V
0
5
C512
C514
R525
100k
0.1u
0.1u
15M_1
33M_1
4 R532 100
R524 0
R698 0
R528 0
R697 0
R511
R514
MCDIAF
R521
R520
3
22
47k
47k
0
D1
D0
D3
D5
D2
D4
R533 0
A16
A17
/MCCSAF
M13
G10
G11
G13
G12
C11
C12
C13
H13
H12
H11
H10
N13
D11
D12
D13
B12
B13
K13
K12
K11
K10
E10
E11
E12
E13
F10
F11
F12
F13
L13
L12
J13
J12
J11
J10
C824 1000p
R552 100k
R554 100k
R556 100k
R557 100k
6
CLKMD1
D1
BDX1
X1
BFSX1
CLKMD3
D0
TMS
EMU0
CLKMD2
A18
A16
D3
HD3
TDI
D5
HPI16
TDo
TCK
D2
RS
HD2
A17
D4
CLKoUT
X2_CLKIN
CVDD3
CVSS5
DVSS3
DVDD3
HPIENA
DVSS2
DVSS4
EMU1_oFF
TRST
ToUT
A13
A19 M12
4 A12 DVSS7
A20 N12 R536 0
B11 BCLKX1 MCSCKAF
CVSS9 L11
C503 A11 CVSS8
DVDD5 M11 R537 0
0.1u D10 HD1 FSDET
D6 D6
C10 N11 C518 1u
D7 D7 CVDD5
B10 L10
D8 D8 INT3 INT3
A10 M10
D9 D9 INT2
D9 N10
D10 D10 INT1 /DINT
C9 K9
D11 D11 INT0 /SYMTIM
B9 L9
D12 D12 NMI /DWUP
A9 M9
HD4 HBIL
D8 N9 R558 100k
D13 D13 IACK
C8 K8
3 D14 D14 BDX2 BDX2
R501 B8
D15 D15 L8 R538 100
100k BDX0 MCDICN
5 A8
HD5 M8 R539 0
HD0
C504 B7 N8
R553
CVDD6 DVSS6
100k
0.1u A7 IC502 C516 0.1u
CVSS10 K7
C7 DSP DVDD4
/RD HDS1
D7 L7 R540 100
DVSS8 HRDY
A6 N7
/HDS2 HDS2 BFSX2 /BFSX2
C506 B6 M7 R541 100
DVDD6 BFSX0 /MCCSXCN
0.1u C6 C517 0.1u
A0 A0 N6
D6 CVDD4
A1 A1 M6 R696 6
A5 HINT
A2 A2 L6 100k
B5 CVSS7
A3 A3 K6
C5 BCLKX2 BCLKX2
HD6 N5
D5 BCLKX0
A4 A4 M5
A4 BDR2 BDR2
A5 A5 L5 R544
B4 HCNTL1
A6 A6 K5 100k
C4 BDR0 MCDOCN
A7 A7 N4
A3 BFSR2 BFSR2
A8 A8 M4
B3 BFSR0 /MCCSRCN
A9 A9 L4
C505 C3 BCLKR2 BCLKR2
CVDD7 K4
0.1u A2 BCLKR0
A21 N3
B2 DVSS5
DVSS9
M3 R542 100k
HCNTL0
N2 R543
BCLKR1
N1 0
R686 100k
R693 100k
R694 100k
R695 100k
CVSS6
MP_MC
MSTRB
IoSTRB
CVDD1
CVDD2
READY
DVDD1
DVDD2
HoLDA
CVSS1
CVSS2
CVSS3
CVSS4
DVSS1
BFSR1
HR_W
BDR1
HoLD
R584
MSC
R_W
HCS
HAS
HD7
A22
A10
A11
A12
A13
A14
A15
R685
IAQ
0
BIo
DS
PS
XF
IS
100k
3
M1
B1
J1
K1
L1
C1
H1
A1
D1
G1
F1
E1
J3
K3
L3
M2
H3
J2
D3
G3
K2
C2
L2
H2
J4
F3
D2
E3
G2
H4
D4
F2
G4
E2
F4
E4
R507
R529 0
R512
/MCCSAF
100k
0
R531
R516
R527
100k
100k
100k
A11
A10
A13
A15
A12
A14
MCDOAF
MCSCKCN 6
3
33M_1
R567
150
15M_1 R560
0 BCLKR0
C511
C509
C513
C507
0.1u
0.1u
0.1u
0.1
RXC
BCLKX0
5 1
/SCRST
/CS3
/WR
HD7
7 7 7
5
2 2 2
1
85
X57-738 (A/2) 6/16
AE AF AG AH AI

HD2 HD2
X2_CLKIN X2_CLKIN
33BU
33M
50C
3 3 3
4 4 4
5 5 5
/CS0
/CS2
/RD
/RD
SCTAM1
A16
4 4
D10
D12
D0
D14
D8
D3
D6
D5
D2
D2
D7
D7
3 D
3.31V
A0
G3
G2
G1
E6
E5
E4
E3
E2
E1
E6
E1
F6
F5
F4
F3
F2
F1
F6
F4
F3
F1
3 C515
5
1u
NC
NC3
A0
A16
DQ10
DQ0
NC2
DQ8
DQ6
DQ5
oE
DQ12
DQ2
DQ2
CE
CE
VCC2
DQ14
DQ7
DQ7
VSS2
4
G4 D6 L522
A16 A16 VCC1
G1 D6 G5 D1
oE A15 A15 A15 A15 VSS1
G2 D5 G6 C6
3.31V D9 DQ9 A11 A11 DQ3 DQ1 D1
G3 D4 H1 C4
L501 D11 DQ11 A19 A19 A9 A9 IC503 A5
G4 D3 H2 C3
VCC A20 A20 A10 A10 NC1
G5 D2 H3 SRAM C1
D13 DQ13 A5 A5 A11 A11 DQ5 D5
C501
C502
G6 IC501 D1 H4 B6
1u
1u
D15 DQ15 A1 A1 A12 A12 DQ0 D0

H1 FLASH ROM C6 H5 B5
VSS1 A14 A14 A13 A13 A7
H2 C5 H6 B4
D1 DQ1 A10 A10 A14 A14 A4
H3 C4
D3 DQ3 A21 4
DQ4
CE2
H4 C3
WE
A0
A1
A3
A6
A8
A2
D4 DQ4 A18 A18
H5 C2
D6 DQ6 A6 A6
B1
A1
B3
B2
A3
A6
A5
A2
A4
H6 C1
VSS2 A2 A2
D
WP/ACC
RESET
RY/BY
A1
3
A0
A3
A6
A8
A5
A2
A4
A7
A13
A17
A12
WE
A3
A7
A9
A4
A8
3
B1
A1
B3
B6
B5
B2
A3
A6
A5
B4
A2
A4
/WR
D4
R522
470k
R509
A13
A12
A17
0
A3
A9
A8
A7
A4
3 D
R504
/FRST
100k
/WR
/WP
5
33M
L905
L904
IC504 RTC
R561
DELAY
47k
R551
3.31V RESET (MCU) RV5C386A 3.31V

100
IC505 R545
IC506 L523
TC7SH08FU-F 0 1 10 33BU
XC6109C29ANN 32KOUT VDD
3.31V
2 9
1 INB 5 SCL OSCIN
VCC 1 4
VIN VoUT 3 8
2 INA SDA OSCOUT
32768Hz
4 7
X501
3 4 INTRB CLKC
GND 2 3
VSS CD 5 6
0.01u
C520
oUTY VSS INTRA

0.01u
C523
C522 8
C521
D 0.01u
0.01u
D
I2CCK
I2CDT
/RINT
D
32K
8 IC509
0.01u
C529
TC7WT125FUF 4.99V
1 G1 8 50C
VCC
2 A1 7
3 Y2 G2 6
AIO7
4 Y1 5
GND
33M A2
D
SCTAM1
BUFFER AMP
(BER CLK/BER DATA)
AIO6
6 6 6
BCLKR0
BCLKX0
RST
1 1 1
2 2
SCBSY
7 7
/BER_EN
BDX2
/BFSX2
HD7
BCLKR2
BCLKX2
/SCRST
BDR2
INT3
BFSR2
BUFFER AMP
(OP : 20PIN BER CLK/BER DATA)
L506
IC507
TC7SH126FU-F 3.31V
SCRXD
2 1 G 5
VCC
2 INA SCTXD 9
R575
10k
3 4
GND
oUTY
R593
C527
0
R578 0
R576 0
R580 0
R579 0
R583 0
R582 0
R585 0
R586 0
R589 0
R588 0
R592 0
R590 0
R595 0
2 0.01u
D
C534
100p
D
20
19
18
17
16
15
14
13
12
11
10
2
1
CN549
86
X57-738 (A/2) 7/16
AJ AK AL AM AN

HD2 HD2
X2_CLKIN R572 22 X2_CLKIN
ASQDET
33A_2
33A_2
3 R720 R577
4 100k 1k
5
C18
C16
U18
U17
R13
B16
B18
B17
A18
A17
V18
V17
T17
T16
F15
N4
C5
C3
U2
U1
D5
D6
D4
B2
B1
A3
A2
A1
V2
V1
F3
T1
J4
NC21
NC11
NC1
ADC1
3
NC30
NC20
NC10
NC29
NC28
NC26
NC23
NC19
NC18
NC16
NC13
NC9
NC8
NC6
NC3
NC25
NC15
NC5
NC22
NC12
NC2
MICIR
NC27
NC24
NC17
NC14
NC7
NC4
IFIR
R569
4 22 A4
5 XTALI
B4
XTALo
A10
32K 32I
A12
DSPCK
B11
/RINT CKo
A11
/HINT USRCKI
H18
A0 ADD0
J18
A1 ADD1
8 K18
A2 ADD2
L18
A3 ADD3
M18
A4 ADD4
N18
A5 ADD5
J17
A6 ADD6
K17
A7 ADD7
M17
A8 ADD8
N17
A9 ADD9
P17
A10 ADD10
K16
A11 ADD11
L16
A12 ADD12
M16
A13 ADD13
P16
A14 ADD14
J15
A15 ADD15
K15
A16 ADD16
M15
A17 ADD17
N15
A18 ADD18
P15
A19 ADD19
J16
4 A20 ADD20
H15
5 ADD21
G17
D0 DT0
H16 IC510
D1 DT1
G15 MCU
D2 DT2
F18
D3 DT3
F17
D4 DT4
G16
D5 DT5
E18
D6 DT6
E17
D7 DT7
F16
D8 DT8
D18
D9 DT9
D17
D10 DT10
B15
D11 DT11
D16
D12 DT12
8 C15
D13 DT13
D15
D14 DT14
E15
D15 DT15
A15
/WR WRITE
8 A16
/RD READ
B14
BHE
C14
BLE
A13
CS4
D13
/CS3 CS3
C13
8 /CS2 CS2
B13
CS1
A14
/CS0 CS0
B12
/HRDY HRADY
D14
/HDS2 HDS2
R18
TXD0 TXD0
T18
RXD0 RXD0
R16
RTS0 RTS0
R15
CTS0 CTS0
U15
TXD1 TXD1
T15
RXD1 RXD1
V15
TXD2 TXD2
6 V14
RXD2 RXD2
T14
MICADC0
MICADC1
TXD3
MoDDAC
SPCS00
SPCS01
SPCS02
SPCS10
SPCS11
SPCS12
SPDAC
SPCK0
SPCK1
MICVR
PWM1
PWM2
KEYo0
KEYo1
KEYo2
KEYo3
KEYo4
KEYI0
KEYI1
KEYI2
KEYI3
KEYI4
ADC4
ADC5
ADC6
ADC7
ADC8
ADC9
RXD3
SPo0
SPo1
SPI0
SPI1
SCK
SDT
TI
5 9
AMT
J1
K1
U11
H1
T11
V11
J3
C10
U10
K3
U6
H3
U5
A9
J2
G3
T10
K2
L2
U12
H2
R9
T6
T8
T5
V13
U4
V6
U7
V8
V5
T12
P4
V12
R14
R4
T4
V4
V7
1 RXD3
R587 1k
R568 1k
2 I2CCK
10u6.3
R591
C533
C535
+
0.1u
SCBSY
1k
I2CDT
OPT10SEL
R611
R612
1M
1M
R597
OPT11
OPT1
1k
OPT3
OPT8
OPT6
OPT5
OPT2
OPT7
OPT4
D D
I2CCK 9
6
I2CDT
TONESW
R687 4.7k
/EVCS
STSW
TONE
SDO0
SCK0
BEEP
RXAF
W_/N
/PCS
MOD
BLVL
R688 4.7k
MIC
1 1 1
9
I2CCK
I2CDT
SDO1
SCK1
THP2
8
/WP
MPL
9
CV
2 2 2
5 5 5
33A_2 R503 1k
6 6 6
32K
SCBSY
87
X57-738 (A/2) 8/16
AO AP AQ AR AS

HD2 HD2
X2_CLKIN X2_CLKIN
ASQDET
15M
33A_2
33M
33M
3.29V R603
0.01u
C540
C538
C539
C537
0.1u 33A
0.1u
1u
0
U16
C17
K14
P12
P13
V16
J14
M1
G5
G4
H5
U3
H4
C4
D3
B3
K5
K4
A5
P7
P8
E6
E5
E4
F5
T3
F4
T2
L1
L3
J5
E12
DGND11
AVCC1
NC36
NC35
L508
NC34
DGND10
AGND9
AGND8
AGND6
AGND3
DGND13
DGND9
DGND8
DGND6
AGND5
DGND15
DGND5
AGND2
DGND12
AVCC10
AGND7
AGND4
DGND14
DGND7
DGND4
AVCC9
AVCC8
AVCC6
AVCC5
AVCC2
AVCC4
DGND3 2
E11
DGND2
E10
DGND1
L5 C547 0.1u 33M_4
DVDIo7
P6 C548 0.1u
DVDIo6
P11 C549 0.1u
DVDIo5
L903
L14 C550 0.1u
DVDIo4
H14 C551 0.01u
DVDIo3
E13 C552 1u
DVDIo2
E7
DVDIo1
M5 C554 0.1u 3.31V 2
DVDD10
N5 C555 0.1u
DVDD9
P9 C556 0.1u
DVDD8
P10 C557 0.1u
DVDD7
N14 C558 0.1u
DVDD6
M14 C559 0.01u
DVDD5
G14 C560 1u
DVDD4
F14
DVDD3 D ASQDET
E9 1.48V
DVDD2 L511 BSHIFT
E8 15M
DVDD1
B5
GPIo11 /H_L
C6
GPIo10
B6
GPIo9 1
A6 R680 0
R677
470k
GPIo8
U8 SBC
GPIo7
R8 R681 0 D
GPIo6
R7
GPIo5 /INAMT
T7 R622 0
GPIo4
R682 0 33M
V10
GPIo3
R676
R625
R624
100k
100k
100k
U9 R683 0
GPIo2
V9 D
GPIo1 /OVRB
T9
GPIo0 /INT25P
C11 R618 1k
SIMRST /IGN
D12 R619 1k
SIMCK /PSW
C12 R620 1k
SIMDT /BINT
R621 0 C621 2
R5
SYMTIM /SYMTIM 9 1
R6 0.01u D
FSDET FSDET
R2
TXRVE TXC
P3
TRAMP DSW
P2
TMoD /PRST
M4
PSTPA W_/V
R1 R623 100k
PSTIF
N3
PSTPLL MM
N2
RXRVE MM2
P1
RXSLT /T_R
L4
PSRRF RXC
M2
R627 100k
R628 100k
PSRIF 6
M3 450K
PSRPLL
N1
R684
RSSIT
100k
PLD
D8 R615 0
VFRM /DWUP
D7 R616 0 D
VoINT /DINT
C7 ∗R922 0
MCo2
D10
MCCS2
C8 R617 1k
MCCK2 PLD
D9
C814
470p
R629
MCCR1 /MCCSRCN
1M
B7
MCCX1 /MCCSXCN
C9 D
MCo1 MCDOCN
B8
MCI1 MCDICN
A7
MCCK1 MCSCKCN
B10
MCCS0 /MCCSAF
B9
MCo0 MCDOAF
D11
MCI0 MCDIAF
FCDADC
BSCAN0
BSCAN1
IFADCN
IFADCP
SQDAC
A8
TEST0
TEST1
TEST2
TEST3
MCCK0 MCSCKAF
RTCK
ADC0
DAC0
ADC3
ADC2
TRST
BooT
RSTo
IFVR
TMS
TCK
RST
TDo
R3
TDI
IFR
AGCDAC /SCSW
D1
G1
R11
F1
E1
U13
N16
L15
P18
G18
R10
T13
C2
U14
H17
L17
E16
V3
D2
E3
G2
C544
R12
F2
R17
E2
100p
R614
470k
C541
0.1u
D D 9
R606 10k
R608 1k
C542
R845
R602
R604
10u6.3
1k
1k
0
+
D R701 R706
100k 68k
9 9 9
R691 100k 33A-2
R692 100k
ASQAPC
R610
R605
R607
1k
1k
RST
1k
1 1 1
ASSIST
RFAGC
/FRST
VAGC
6
RSSI
THP
2 2 2
5 /DRST
6 6
SCBSY
X57-738X-XX R922
0-10 K NO
0-12 HK 0
88
X57-738 (A/2) 9/16
AT AU AV AW AX

HD2
X2_CLKIN 2
80C
50C
33M
33GPS
2 2
/PCS_RF
R915
33M-4 0
IC511
TC7SH08FU-F 3.31V
L521
1 INB 5
3.31V VCC
2 INA
3 4 D503
GND
IC508 oUTY 1SS416
SM5023CNDH-G X502
0.01u
C536
18.432MHz AND REVERSW
4 3 C530 CURRENT
Q VSS (PCS RF/HD2)
5 2 0.01u 3 2 PREVENTION
VDD XT oUTPUT GND (PCS RF)
6 1 R594 D
XTN INHN
4 1 1k
R581
470k
VCC VC
C528
0.1u
0.01u
C532
R596
BUFFER AMP
100k
(18.432MHz)
C531
0.1u D
D
BSHIFT
/PCS
1 1 1
50C
L507
80C L518
33GPS
13
9
26P_RD
26P_TD
TXO
DT1
OPT11
OPT1
G_RXD2
OPT10
RXEO
25P_TXD2
TXI
OPT3
OPT8
OPT9
OPT6
OPT5
OPT2
OPT4
OPT7
RXEI
D501
L510
L509
1SS388F
D502 D
1SS388F
R598 1k
R599 1k
R600 1k
R601 1k
9 13
D501,502
L517
LINE
PROTECTION
450K 450K
PLD PLD
13 13
OPT10
DTI
TXI
TXO
9 9 9
OPT11
OPT1
26P_RD
26P_RD
RXEO
OPT3
OPT9
OPT8
OPT6
OPT5
26P_TD
26P_TD
AO
OPT2
OPT4
OPT7
RXEI
RXEI
AI
RXEO
C567 1000p
C579 1000p
C543 100p
C545 100p
C546 100p
C553 100p
C561 100p
C562 100p
C563 100p
C565 100p
C566 100p
C568 100p
C569 100p
C570 100p
C571 100p
C572 100p
C573 100p
C574 100p
C575 100p
C576 100p
C577 100p
C578 100p
9
L512
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
1
4
5
6
CN595
CONTROL (E23-1278-05) VCO (E23-1278-05) RX-IF GND DIGITAL GND
CN506 CN509 CN611 CN512 CN516 CN527 CN540 CN543 R562 0 R534 0
R548 0
CN612 CN614
RX-IF (E23-1278-05) RX-FRONT (E23-1278-05)
R565 0 R574
CN503 CN505 CN507 CN510 CN502 CN504 CN508 0 C620
0.01u
D D
TX-MODULE (E23-1278-05) TX-DRIVE (E23-1278-05) AVR (E23-1278-05)
CN511 CN513 CN517 CN520 CN542
89
X57-738 (A/2) 10/16
AY AZ BA BB BC
2 2 2
33A_2
33A_2
IF_DET
OPT10
R726
10
3.28V BUFFER AMP 11
(2nd IF DET) 2nd IF BUFF
3.28V
C729
0.1u
5
R : 0V 1.63V
MCP6021-E/OT
T : 1.63V
VIN-
VDD
IC706
MIC AA TC75W51FK(F)
0.01u
IC704
C714
R730
R733
R717
1.63V
47k
10k
33k
C707 R716 1 8
VDD
1 VoUT
0.1u 0 7
VIN+
VSS
OPT10
C721
220p
R724
56k
R725
C736
100p
R749
82k
1.65V R722 68k 2
3
2
68k 3 6 R748 R753 C742 R766 C748

C710 C732
1200p
C715
1.63V DTI
4 5
0.01u 0.01u 1.63V 0 56k 0.1u 100k 0.1u
R759
VSS
100k
1.31V 1.31V
0.01u
C725
R734
22k
LPF/SUM AMP MIC SUM2
MIC
IC702 C744
C706
330p
TC75W51FK(F) 0.1
1.65V 1.63V
R714 5 4
VSS 1.62V IC708
C701 R705 100k 6 3 3.28V
MOD TC7W53FK(F)
3.3u 100k 2 R739
C712
R710
1.63V
100k
68p
1 8 R767 C762
1.62V 0 CoMMoN VCC
R741
100k
7 2 7 47k 0.1u
INH CH0 TXI
8 1 R731 3
VEE 6 R768 C763
1 VDD CH1 TXO
0 4
R745
100k
3.28V GND 5 47k 0.1u
LPF (MOD) A
C720
R765
AF SW
1k
0.1u (TXO/TXI) 13
MOD SMF
SCSW(MIC)
/SCSW
33A-2
VREF
D704,705
AF DETECTOR Q704,705
(LIMIT) LIMIT
D704 Q704
RB706F-40 2SC4738(GR)F 11
R784
150k
1000p
C791
C765
C750
0.1u
1u
D705
C751
R813
0.1u
4.7k
C766
RB706F-40
1u
R815
100k
R809
100k
R787
270k
Q705 C794
2SA1832(GR)F MUTE (MI2)
R793
10u
0
Q707
450K R779 MUTE (MI1) 2SJ243-A
1.62V 470k 1.62V 3.26V
Q706
PLD MIC SUM1 2SJ243-A
1 C764 R786 C773 R796 C782 C787 C795
13 22p 39k 0.1u 10k 0.1u 10u 3.25V 10u
R816
100k
33A-2
R804
R812
680
4.7k
3.28V R : 3.31V
T : 0V
1000p
C793
9 SUM AMP
8
7
6
5
(AI/TONE/MI1/MI2)
/(MOD/DI)
VDD
R798 C784
1
IC709 680k 0.1u
C770
0.1u
TC75W51FK(F)
VSS
R797 C783 R806

MOD SUM 2
330k 0.1u 5.6k
1
3
2
R789
1.63V 0
R801
100k
R773 680k
1.63V
C757 15p
R774 470k
C815 10u
R775
82k
C816 10u
1
9 13
11 11
6 10 10
13
PLD
MM2
MM
1 1 1
13 13
9 9 9
MI2
MI1
ME
90
X57-738 (A/2) 11/16
BD BE BF BG BH

2
50R
33A_2
33A_2
OPT10 OPT10
11 11 11
SQ VOLTAGE
CONTROL
D702 R755
HSC119 10k
2 2 2
W_/N
FMDET
APC
R843
470
R729
100k
ASQ DET C722
R746
10k
R837
4.7k
3.28V 47p
C818
1u
NOISE
DETECTOR (SQ)
R750
3.3k
8
7
5
D703
R760
VDD
RB706F-40
R838
IC705 1.5k
0
C719
BRF/BUFFER
0.1u
TC75W51FK(F) C740
AMP (SQ)
4700p
R761
VSS
100k
C741
0.15u
1000p
C738
R747
330k
1
3
2
R762
470k
C734
ASQ BPF
TH701
100k
-t °
R707 0.01 Q702
15k C716 2SC4617(Q)
220p R727 NOISE
R721
2.2k
1000p
AMP
C821
R709
8.2k
R751
270k
C737
0.1u
C718
270
220p
Q701
SSM3K15TE(F)
R715
47k
VREF VREF
33A_2
IC703 3.28V
TC75W51FK(F)
1200p
C705
R718
1 8 VIN8
0
VDD
7
C727
R740
100k
82p
2 R737 R744 C735

R703 R712 3 6 47k 47k 4.7u
10k 68k 4 5
VSS
C709
220p
LPF
C730
C723
560p
0.1u
(APC/DEO)
APC SMF
DEO BUFF
C717
0.1u
RXAF SMF
IC701
TC75S51FE(F)
3.28V
1 IN+ 5
C708 VDD
1.64V 1200p 2 1.62V
VSS
C702 R704 R713 3 4 SCSW(RXAF)
1u 56k 56k IN- oUT
1.62V IC707
R732
47k
LPF (RXAF) TC7W53FK(F)

C711
R738
180p
R708
68k
1k 5 4 10
A GND
R728 6 3
CH1 VEE
0 7 2
CH0 INH
8 1
VCC CoMMoN
3.28V
C731
0.1u
RXAF/RXEI SW
C726
C724
0.1u
0.1u
10
R752
1k
0V
10 10
PLD
ASQAPC
ASQDET
/SCSW
RXAF
W_/N
AMT
1 1 1
RXEO
RXEI
9 9 9
MI2 MI2
MI1 MI1
ME ME
91
X57-738 (A/2) 12/16
BI BJ BK BL BM
33A-2
50C
OPT10 /INAMT
11 11
/INAMT
1
2
SDO0
SCK0
/EVCS
2 2
TV1
TV2
MP
TCXO_MOD
VCO_MOD
1
C776
R833 100
R834 100
R835 100
1u
C777 1.62V
1000p
12
11
10
9
8
6
5
4
3
2
1
VIN1
VoUT1
DI
LD
CLK
VIN3
VDD
VIN2
VIN4
VoUT3
VoUT2
VoUT4
M62364FP-F
R817
3.28V
47k
1.62V
IC712
DAC
Q708
VDAREF
2SA1832(GR)F
RESET
C799
VoUT5
VoUT6
VoUT7
VoUT8
GND
VIN5
VIN6
VIN7
VIN8
D0
0.1u
R820
470k
OPT10
21
SW
20
13
16
18
19
23
15
22
14
17
24 R818
R836 OPT10SEL
33k
0 R821
1000p
C774
C789 4.7u 0
C790 10u R822
C813 10u D706 D707 100

1.62V
EMZ6.8N EMZ6.8N
LINE LINE
VREF PROTECTION PROTECTION
(DI) (DEO)
VIN8
33A-2
9
VREF
IC711
1000p
3.28V
C754
R783
TC75W51FK(F) R810
0
R780
100k
1.62V OPT6
1 8 RX SUM 1k
VDD
7
VGS REC SEL
1.62V
C779
VREF
68p
2
IC713
R802
R799
3
27k
R795
220k
6
56k
TC7W53FK(F)
4 5 5 4
VSS 1.62V A GND
C761
0.01u
R781
100k
6 3
CH1 VEE
C778
R794
0.1u
SUM AMP 7 2
0
(AF) / VREF CH0 INH

8 1 C797
VCC CoMMoN AO DEO
0.1u
DI
3.28V AO SW
R800
R803
4.7k
15k
C788
R790
0.1u 1
220k
6
10
C767
3.28V
0.1u
1
IC710
2
R770
56k
TC7W53FK(F) 50C
C745 R764 R776
0.01u 120k 330k 1 8
CoMMoN VCC
R807
2 7 AFO BEFF
10k
C749 C752 R777 INH CH0

0.1u 0.01u 150k 3 6
VEE CH1 IC714
4 5 R792 TC75S51FE(F)
R756 R758 C747 R771 C753 R778 4.98V
15k 10k 0.01u 100k 0.01u 390k GND A
C786
R808
0.1u
1k 1 IN+ 5
10k
VDD
AF SW 2
0.01u
0.01u
C743
C746
C796
R763
0.1u
18k
(AI TONE OPT9/VREF) VSS

C785 R805 3 4
R772
12k
SIDE TONE MUTE 0.1u 82k IN- oUT

C792 47p C798 R819
R782 R785 C775 R791 LEVEL
15k 10k 0.1u 560k 0.1u 0
SHIFT (TXD) R814
100k
R846
3.3k
0.01u
0.01u
R769 Q703
C768
C769
R788
22k
SSM3K15TE(F)
4.7k
TONE SW
9
TONESW
STSW
TONE
BEEP
1 1 1
AFO
OPT9
AFO
AI
9 9 9
MI2 MI2
MI1 MI1
ME ME
92
X57-738 (A/2) 13/16
BN BO BP BQ BR

SB
SB
R826
10k
R825 C801 C802 R828
10k 1u 1u 0
/INAMT
R827
3.3k
0V
R662 470k
R823 Q710
R663 470k DTC363EU
4.7k
C820
AF
1u
50C Q709 MUTE
/INT25P DTC114EE
R659 100k
R660 100k
R661 100k
R672 100k
R673 100k
R674 100k
C591
DA204U
0.01u DC
D512
LINE SW
PROTECTION
IC514 (AID9)
TC7WBD125AFK 4.98V
1 8
18
17
16
15
14
13
oE1 VCC
2 7 PA
R646
R648
6.8k
6.8k
I2CCK A1 oE2
A0
P16
P13
P15
P17
P14
3 6 19 12 HOR
I2CDT B2 B1 SCL P12 AO2
4 5 20 11
GND A2 SDA IC517 P11 AO1
21 10
4.98V VCC I/O P10 AIO9
22 EXPANDER 9
INT GND
23 8
A1 P07 AIO8
LEVEL SHIFT 24 7
C596
0.1u
9 A2 P06 AIO7
(I2CCK/I2CDT)
P00
P01
P02
P03
P04
P05
R671
R670
100k
100k
1
6
5
2
4
50C R664 100k
REVERSE LINE R665 100k
33M CURRENT PROTECTION
DA204U
PREVENTION (RXD2)
D511
R666 100k
R640
10k
(OR G RXD2) 12
R651
D506 R667 100k
1k
RXD2
1SS416 R668 100k
R842
REVERSE 1k R669 100k
D507 CURRENT
PREVENTION
1SS416
R658
(OR RXD2)
AIO1
AIO3
AIO6
AIO5
AIO2
AIO4
G_RXD2
0
12 12
AIO6,AIO7 9 9 9
50C
0.01u
IC513
C618
R678
100k
TC7SET08FU-F
1 INB 5
VCC 4.98V
2 INA
TXD2
3 4 R644
GND RXD2/DI
oUTY 0
BUFFERAMP (TXD2)
TXD2/AUXIO9
LINE D508
PROTECTION DA204U
25P_TXD2
DEO
DI R650
0 TXD0
33M
0.01u
C595
IC516
R641 100k
R642 100k
R638 100k
TC7WH126FU-F RXD0
R637 10k
R639 1k
1 G1 8
VCC ME
2 A1 7 3.31V
MI2
R656
3 Y2 G2 6
470
RXD3 DEO
4 Y1 5
GND
A2
IC518
LEVEL SHIFT ADM202EARNZ
CTS0
(RXDO/CTSO)
50MC 9 8 C614
R2oUT R2IN
RXD0 10 7 1u
T2IN T2oUT DI/RTS
11 6
1SS416
1SS416
REVERSE C615
D510
D509
T1IN V- AFO
CURRENT 12 5 1u
PREVENTION R1oUT C2-
13 4
26P_RD
R652
R1IN C2+
100k
14 3
T1oUT C1-
15 2 C616
GND V+
16 1 1u
VCC C1+
C592
100p
C593
100p
50M C613
0.01u
C612
R690
R689
470k
470k
IC515 5.01V
5.01V RS-232C 1u
TC7WT126FU-F
9 DRIVER
1 G1 8
VCC
2 A1 7
RTS0
3 Y2 G2 6
4 Y1 5
GND
A2
0.01u
C594
LEVEL SHIFT
(TXDO/RTSO)
TXD0
R636
0
26P_TD
AFO
9 9 9
MI2
MI1 MI1
ME ME
93
X57-738 (A/2) 14/16
BS BT BU BV BW
NX-700/700H TX-RX UNIT (X57-738X-XX) (A/2)

SCHEMATIC DIAGRAM
SB
IC715
GND1
GND2
LA4425A
OUT
VCC
IN
13.54V
1
5
2
1.34V 1000p
47u25
C805
C807
+
1000p
1000p
C803
C804
6.38V
330u16
C806
+
1000p
C809
1000p
C811
CN705
1 SB
2 SPI
R831 3 SPO
PA 0 4 PA
HOR 5 HOR
6 GND
C810
470p TX-RX UNIT (X57-738X-XX) (B/2): D-SUB25
D901 D903 D907 D911
J701 LINE LINE LINE LINE
PROTECTION PROTECTION PROTECTION PROTECTION
EXT.SP (BER CK) (AUXIO1) (AUXIO3) (AUXIO8)
D902 D904 D908 D912
LINE LINE LINE LINE
PROTECTION PROTECTION PROTECTION PROTECTION
(BER DT) (AUXIO2) (AUXIO4) (AUXIO5)
DA204U
DA204U
DA204U
DA204U
D901
D911
D903
D907
A
DA204U
DA204U
DA204U
DA204U
D908
D902
D912
D904
CN600 CN901 R902

30 AUXIO6/BER CK 1 100
12 AIO6 13
C598 1000p R903 C911 100p
9 AIO6 100
29 AUXIO7/BER DT 2
AIO7 12
C599 1000p R904 C912 100p
AIO7 470 J901
28 AUXIO1 3
AIO1 24 27
C600 1000p R905 C913 100p
27 AUXIO2 4 470 13
AIO2 23 13
C601 1000p C914 100p 25
RXD2/DI 25
RXD2/DI 26 5 12
10 12
R906 C915 100p 24
24
25 AUXIO3 6 470 11
AIO3 22
C602 1000p R907 C916 100p 23
TXD2/AUXIO9 23
TXD2/AUXIO9 24 7 470 10
9 10
R908 C917 100p 22
22
23 AUXIO4 8 470 9
AIO4 21 9
C603 1000p R909 C918 100p 21
21
22 AUXIO8 9 470 8
AIO8 8 8
C604 1000p R910 C919 100p 20
20
21 AUXIO5 10 470 7
AIO5 20
C605 1000p R911 C920 100p 19
AUXIO9/CTS 19
R654 20 11 470 6
AIO9 4 6
0 C921 100p 18
19 AUXO1 12
AO1 5
C606 1000p R912 5
470 17
TXD0 18 TXD0 13 17
3 4
17 AUXO2 14 C909 100p 4
AO2 16
C607 1000p OVER DC 16
SUPPLY PROTECTION R913
470 3
RXD0 16 RXD0 15 3
2 15
15 GND 16 C910 100p 15
2
ME 14 ME 17 2
L901 19 14
MI2 13 MI2 18
6 1
DEO 12 DEO 19
C904
100p
02DZ18F-X
C908
100p
C608 100p 26
1000p
11 GND 20
C902
D905
C906
100p
A
A A A
C905
100p
10 50C 21
A A L902
C609 1000p
DI/RTS 25
DI/RTS 9 22
5
AFO 8 AFO 23
17
C610 100p
F501 16
7 SB 24
6 SB 25
2A
1000p
C923
C901 100p
C903 100p
02DZ18F-X
5 SB 26 REVERSE REVERSE
1SS355
1SS355
D906
D909
D913
4 SB 27 CURRENT CURRENT
PREVENTION A PREVENTION
3 SB 28 (SB) (SB)
1000p
C611
2 SB 29
A A A
NC/RSSI 15
1 30 OVER DC Q901 Q902
02DZ18F-X
02DZ18F-X
SUPPLY QSX6 QSX6

1000p
C597
1000p
1000p
R901 R914
C922
C907
D910
D914
PROTECTION
470 470
DC SW DC SW
(AUXO1) A (AUXO1) A
OVER DC OVER DC
SUPPLY SUPPLY
PROTECTION PROTECTION
SPO
50C
SB
9 9 9
MI1 MI1
ME ME
94
X57-738 (A/2) 15/16, X57-738 (B/2) 1/1
BX BY BZ CA CB
R924
1k
1000p
C925
R925
1k
1000p
C922
"PF4" VOL UP
R922
CN902 1k
1000p
C923
CH UP "PF3" VOL DOWN
2
SP 1
R923
1k
1000p
C924
CH DOWN "PF2" "PF1"
TX-RX UNIT (X57-738X-XX) (B/2)
R921
R920
R904
HSC119 100
HSC119 100
HSC119 100
CN597 CN901 D908,911,912
D911
D908
D912
30 1
SPO SPO KEY MATRIX
29 2
SPO SPO
28 3
SPO SPO
KO1
KO0
KO2
KI1
KI0
KI3
KI2
27 4
C580 SPO SPO
26 5 15
100p SPO SPO
25 6 3.12V
SPO SPO SPO
C581 PSW POWER
24 7
GND GND
1000p 23 8 8C
80C 8C 8C
C582 22 9
SB SB
1000p 21 10
SB SB SB
C583 20 11
R630 NC NC
1k 1000p 19 12
/PSW PSW /PSW
18 13
GND GND
C584 17 14
GND GND
100p 16 15
MIC MIC
9 C585
100p 15 16
ME ME
C586 14 17
GND GND R901
0.01u 13 18 0
AFO AFO AFO
12 19 /PRST
RST2 (LCDCE) /PRST
C587 1000p 11 20
(LCDCLK) GND
02DZ18F-X,Y
Q501 10 21 5C
UPA672T-A (LCDDI) GND
DC SW
1000p
9 22 TXD
C914
D907
(LCDDO) GND
8 23 RXD
GND GND
/PRST
R506
470k
D907
OVER DC
R523 47k SUPPLY
PROTECTION
C588 1000p 7 24
SHIFT/MODEL SHIFT
6 25
5C NC
C589 5 26
0.01u
C817
NC 5C
1000p
4 27
TXD TXD
D504 3 28
RXD1 RXD RXD
1SS416 C825 2 29
GND GND
R633 100p 1 30
REVERSE (DM) GND
SCRXD
0 CURRENT
PREVENTION
L901
L902
MINISMDC020F
(RXD)
1u
1u
C908 1000p
C909 1000p
C903 0.01u
R632
C965 0.1u
10k
LINE
D906
PROTECTION
v
(SB)
33M C910 C912
R634
10k
100p 100p
SCTXD J901 C911 100p

TXD1 8 DM/KVL DM/KVL
C590 7 HK/RXD 5.01V HK/RXD
0.01u 6 MIC
5 ME 5.01V
IC512
9 TC7SET08FU-F 4 PTT/TXD PTT/TXDO
3 E
4 oUTY 3
GND 2 SB 13.52V
2
1 BLC/AFO 5.01V R902
5 INA 1
50C VCC 1k
AVRM16080MAAB
AVRM16080MAAB
AVRM16080MAAB
4.98V INB D901 D904

C906 2200p
C907 1000p
02DZ18F-X,Y
C905 0.1u
SURGE SURGE
LEVEL SHIFT
ABSORPTION ABSORPTION
D901
D903
D902
D904
(AND ITXD1/SCTXD)
(DM/KVL) (BLC/AFO)
v
D902 D903
9 SURGE OVER DC
ABSORPTION SUPPLY
(HK/RXD) PROTECTION
MI1
ME
95
X57-738 (A/2) 16/16, X54-364 1/3
CC CD CE CF CG
NX-700/700H SCHEMATIC DIAGRAM
8.00V Q910 7.97V

12A02CH LCD KEY
8C
D921
D931
D919
D923
D925
D933
R938
LCD
10k
R931
R932
TX/RX LED
470
7.27V
560
TX/RX LED (BUSY) BACK
B30-2281-05
B30-2281-05
B30-2281-05
B30-2281-05
B30-2282-05
B30-2282-05
(TX) LIGHT
SW
R939
D920
D926
D936
D935
D922
D932
D924
D934
10k
R :0V R : 5.00V
B30-2282-05
B30-2282-05
Q905 Q906 D915-926 D927-936
T : 5.00V T : 0V
DTC114EE DTC114EE LCD KEY
Q908 BACK LIGHT BACK LIGHT
D930
D916
D918
D915
D928
D929
D917
D927
DTC114EE
1000p
C941
1000p
1000p
C931
C932
R953
R958
R963
R966
R955
R965
R957
R964
270
270
270
270
820
820
390
390
R :0V R :1.98V
T : 1.86V T : 0V 4.99V
0.76V
5C
B30-2304-05
R956
D914
R937
R954
TX/RX
100
47k
Q909,911
47
LED
Q909 DIMMER SW
BLC1 0V (LCD BACK LIGHT)
DTC114EE
GREEN
RED DIMM Q911
SSM3K15TE(F)
1000p
C942
R919 16 5.00V
10k
IC903
8.00V 7.87V XC6204B502PR IC904
5.02V XC6204B332M 3.31V
R918 4 3 L903 L908
VIN CE VOLTAGE 1 5
10 VIN VOUT
C915
2 REGULATOR
4.7u
C930
R930
VSS (5C) 1u
10k
C940
C939
C964
0.1u
VSS
10u
5 1
1u
VoUT NC 3 4
CE NC
C916
1u
5.02V VOLTAGE
REGULATOR (33C)
15 15 15
16
33C
8C
5C 5C 5C
R916
IC908
10k
AF BUFFER AMP
R936
47k
(AFO) TC7SH08FU-F
IC902 4 oUTY 3
R917 10k
TC75S51FE(F) GND
5.02V 2
C921
15
0.1u
1 IN+ 5 5 INA 1
C919 VDD VCC
1000p 5.02V INB
C928
2
0.1u
C929
VSS
0.1u
C918 R913
0.1u 82k R915 3 4 AND GATE
(TXD1/RXD0)
47k IN- oUT
C920
120p
R914
100k
16
AFOSW
BLC2
/PRST
5C
19
TXD
LCDADJ
RXD
DM/KVL
PTT/TXD0 17 17
DUAL BUS IC907

D910 BUFFER TC7WH126FU-F
(RXD0/RXD1)
REVERSE CURRENT
PREVENTION(HK/RXD) 5 A2 4 19
GND
6 Y1 3
C917 7 G2 Y2 2
0.1u 5C 5C 8 A1 1
VCC BUCNT2
5.02V 5.02V G1
C927
R935
0.1u
R911
R912
R927
47k
4.7k
47k
33k
IC901
R909
100k
TC7W66FK-F
/PRST
1 8 ON HOOK
1SS416
IN oUT1 VCC : 0V
D910
2 7
oUT IN1 CoNT1
3 6 Q902 Q904
CoNT2 oUT_IN2 DTC144EE DTC144EE
4 5 IC905
GND IN_oUT2 BUS BUFFER TC7SH126FU-F TXD1
Q901 (TXD0)
R999
RXD1
100
AFO/BLC SW SSM3K15TE(F) 4 oUTY 3 RXD0

GND
2
C913
AFO SW
0.1u
TXD0 18 18
5 INA 1
R907
100k
HK/RXD0 SW VCC BUCNT1

5.02V G 2.23V
R934
R905
C926
47k
0.1u
DM/KVL 1k TH901
R940
270k
100k
HK/RXD
-t °
R908
47k
R929 R941
IC906 DC/DC CONVERTER 470k 120k
PTT/TXDO R906
LM2682MMX
DA204U
(N100C) IC909
D913
R926
330 4.86V
10k
LMC7101BIM5
R933 5 4
GND VoUT
100 6 3 4 INPUT- INPUT+ 3
4.7u25
C944
VIN C2-
7 2
1000p
2
C933
C934
C1+ C2+
+
4.7u25
LINE
C943
V+
1u
PROTECTION 8 1
NC C1- 5 1
+
(PTT/TXDO) V-
OUTPUT
C935 -9.69V
0.01u
C945
4.7u25 BUFFER AMP

+ (LCD CONTRAST ADJ)
5C
96
X54-364 2/3
CH CI CJ CK CL

LCD 1
/RES
VDD
VDD
/WR
VSS
/CS
D0
D1
D2
D3
D4
D5
D6
D7
A0
V1
V2
V3
V4
V5
DISPLAY UNIT (X54-3640-10) CN905
11
1
20
10
19
18
16
13
3
15
5
12
2
17
14
4
2
C954 1u
C953 1u
C952 1u
C951 1u
C950 1u
C949 1u
-4.29V
3.30V
C956
0.01u
1000p
C958
R989
470k
R991
R981
C963
100p
R982
20
470k
10k
10k
C955 33C-2
Q913
R974 10k
R972 10k
R971 10k
R970 10k
R969 10k
R968 10k
R967 10k
R973 10k
UPA672T-A R976 100p FLASH ROM
IC913
R962
0
0
29AL16D7KCCA
R960
33C 25
0
A1 A0
3.30V 3.30V 26 24
/CS0 CE A1 A2
23
20
19
18
17
16
15
14
13
12
11
LCD R900 27 A2 A3
8
7
6
5
RESET VSS1 22
TC7WZ245FK-F
B1
B1
TC74LCX245FK
B3
B6
B8
A4
G
B5
A3
VCC
B2
VCC
B2
B4
B7
oE
SW 0
28 21
/RD oE A4 A5
IC910
IC912
29 20
0.01u
0.01u
C960
C959
R990
R988
4.7k
D0 DQ0 A5 A6
47k
30 19
GND
GND
D8 DQ8 A6 A7
DIR
DIR
31 18
A1
A2
A1
A2
A3
A4
A5
A6
A7
A8
D1 DQ1 A7 A8 3
32 17
1
10
3
9
5
2
2
4
7
D9 DQ9 A17 A19
R998
33 16
0
D2 DQ2 A18 /CS1
34 15
BUS BUFFER BUS BUFFER D10 DQ10 RY/BY
/WR
A1
D1
R928
D0
D3
D6
D5
D2
D4
D7
(A1-A2) (D0-D7) 35 14
10k
3.30V D3 DQ3 NC3
20 20 36 13 R986
D11 DQ11 NC2
37 12 10k
VCC RESET
/CS3 38 11
C962 D4 DQ4 WE /WR
33C L907 39 10
0.1u D12 DQ12 NC1
40 9
D5 DQ5 A19 /CS2
41 8
21 D13 DQ13 A8 A9
5C 42 7
D6 DQ6 A9 A10
43 6 21
CP909
CP917
D14 DQ14 A10 A11

100k
100k
44 5
D7 DQ7 A11 A12
45 4
D15 DQ15/A-1 A12 A13
46 3
1SS416
VSS2 A13 A14
D937
15 15 R992 47 2
L905 BYTE A14 A15
KI1
KO1
KI0
KI3
KO0
KI2
KO2
5C 0 48 1
A17 A16 A15 A16 4
0.01u
C948
C957
100p
5.02V
R952
1000p
C966
0 20
16 16
AFOSW
DIMM
BLC1
BLC2 D937
RED
GREEN
BUCNT1
BUCNT2 REVERSE
D1
D10
D0
D3
D6
D8
D9
D5
D2
D4
D7
CURRENT
PREVENTION
19 (SRAM WR)
20 21
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
19
/KI1
BUCNT1
KO1
D1
/KI0
/KI3
/KI2
D0
D10
KO0
D3
D6
D8
D9
D5
BUCNT2
LEDG
KO2
D2
D4
AVCC
D7
LEDR
AVSS
VREF
LCDADJ 1
LCDADJ
2
DIMM
L904
C967 R944 3
17 /LCDRST 75
1000p 100k 4 D11 D11
WP 74
5 D12 D12
R996 AFOSW 73
D13 D13
R945 0 6 72
4.7k
BYTE D14 D14 5
R946 0 71
7 D15 D15
CNVSS 70
8 A0
BLC1 69
9 A1 A1
BLC2 68
C946 100p A2 A2
67
A3 A3
R947 470k 66
A4 A4
R948 10k 65
/PRST 10 A5 A5
RST2 IC911 64
R949 1k 11 30620SPGPU3C A6 A6
Xout 63
12 A7 A7
MCU
11.0592MHz
VSS 62
13 VSS
X901
C938
10p
Xin
C961
61
5.02V
1u
C947 0.1u A8 A8
14 60
VCC1 VCC2
R950 47k 59
15
C936
A9 A9
10p
18 /NMI 58
R942 16 A10 A10
LDM 57
0 17 A11 A11
17 DM/KVL DM/KVL 56
PTT/TXD0
R943 18
/PTT
A12
55
A12 6
1k 19 A13 A13
12KEY_1 54
20 A14 A14
12KEY_2 53
21 A15 A15
12KEY_3 52
22 A16 A16
12KEY_4 51
23 A17 A17
12KEY_10
12KEY_11
12KEY_12
12KEY_5
26 12KEY_8
12KEY_9
24
/HOLD
/HLDA
12KEY_6
BCLK
RXD1
RXD0
TXD1
TXD0
/RDY
/BHE
/CS3
/CS2
/CS1
/CS0
25
/WR
ALE
A19
A18
/RD
NC
NC
12KEY_7
31
41
20 21
30
40
50
38
39
43
46
48
49
28
29
33
36
35
45
32
42
27
34
37
44
47
R977 47k
R978 47k
R979 47k
CP910
CP912
CP908
CP907
100
100
0
0
R997
0
/CS1
/CS0
/CS3
/CS2
/WR
A19
TXD1
RXD1
TXD0
RXD0
/RD
18 L906 21
33C
7
DGND DGND
Note : The components marked with a dot (•) are parts of foil side. 97
X54-364 3/3
NX-700/700H BLOCK DIAGRAM
CN401
DCin +B 33C
F401 IC2
(13.6V) F53-0328-05 LM73CIMKX-0
CN402
GND DCDC I2CCK TEMP
Converter 50M I2CDT SENSOR ASSIST
IC402 33C 50C
IC405 X1
XC6204B332P1 XC6204B332P1 33C L77-3014-05 LM
3.3V AVR 33M
IC408 Q405 VCTCXO
XC6204B332M 2SA1955A-F TCXO_MOD BUFF BUFF
19.2MHz
3.3V AVR 33A DC SW SCTAM1 IC1 Q15
Q416 LMC7101BIM5 2SK1215-E(E) IC3
SSM6L05FU /BINT PLL F
Q412
2SA1955A-F SBC_2 DC SW 33A2
DC SW 50MC Q411 IC
D408 TC7
1SS301F 33M 2SA1955A-F SCK1, SDO1, /PCS_RF
IC409 SBC_2 DC SW 33BU
XC6205B152PRN CN405 PLD IC5
Q404 1.5V AVR 15M /RST Buck UP Battery TC75W
2SJ645 VCO_MOD
RESET /RST
DC SW SB
IC506
XC6109C29ANLN Fin
SBC_2
IC401 8V AVR
XC6108C23CMN 80C 50C
IC403 Q407 50R
Detect /BINT NJM78M08FA-ZB 12A02CH SW
DC SW 80T 2nd Local /T_R
X3 BPF
50C
TXC
Q408 Q203
Protect SBC_2 12A02CH 2SC5636
D401
02DZ18F-X,Y DC SW 80R
Q401 SBC
DTC114EE RXC CF201
(Wide)
DCDC 150C D201 D202
Converter DAN235E DAN235E
CN403 IC410 IF IC
XC9101D09AKR CF CF
E41-0927-05 SW SW IC202
1 TK10931VT
/IGN 5V AVR 50C
Q403 IC404 33C
2 DTC114TE TA7805FQ Q409 CF202
12A02CH (Narrow)
SW
DC SW 50R Q201 DTA114EE
W_/N Q202 DTC144EE
RXC
W_/N SW CD
3.3V AVR 33C
IC406 Q212 CD201
TK71733S EMD9 L79-1850-05
Main_CLK /RST
3.3V AVR 33GPS 33M 15M
IC407
XC6204B332M
RFAGC, ASSIST,
/T_R, W_/N, W_/V
SCK1, SDO1
X502
IC508 L77-3015-05
SM5023CNDH-G CV, THP, THP2, RS
VCTCXO VAGC, PLD, M
Main_CLK BUFF
18.432MHz
SCTAM1 33M 450k
BSHIFT
SCBSY SCBSY
SCRXD 33M 15M
SCTXD Main_CLK IC703(1/2)
TC75W51FK
/SYMTIM, FSDET, /DWUP, /DINT LPF
(for production)
/MCCSRCN, /MCCSXCN, MCDOCN, MCDICN ASQAPC

/MCCSAF, MCDOAF, MCDIAF
CN549
MCSCKAF AI
IC511 TONE
HD2 TC7SH08FU-F OPT9
/PCS_RF
/PCS
IC701
IC502 TC7SH08FU-F TC75S51FE(F)
BCLKX0 IC505 R567 MCSCKCN
DSP LPF
C544
100p
IC509 150 IC510 RXAF

TC7WT125FUF BCLKR0 MCU
RXEO
BER_CLK BUFF
BER_DATA A[0-20], D[0-15], /RD, /WR
/CS0, /CS2, /CS3, /HRDY, /WP
/FRST, /DRST, /HINT, /HDS2
/BER_EN
IC706(1/2)
TC75W51FK(F)
LPF
MIC
33M
IC702(2/2)
IC501 TC75W51FK(F)
FLASH ROM LPF
/RINT MOD
32K
TONESW, AMT, STS
MM, MM2, INAMT, /
TXD[0-3], IFC, TXC, R
OPT10SEL, /EVCS, S
I2CCK, I2CDT
33BU /OVRB, /IGN, /P
33BU CTS0, RXD[0-3]
/INT25P
IC503
SRAM IC504
RTC
RV5C386A OPT[1-8]
X501 OPT11
/RST 32.768kHz
L77-1802-05
98
BLOCK DIAGRAM NX-700/700H
150C 50C
Ripple Q1 Ripple Q7
FILTER 2SC5383-T111 FILTER 2SC5383-T111
/T_R
T/R SW
Q11
ASSIST BUFF SSM6L05FU
Q12
IC4 2SJ347F
LMC7101BIM5
50C D103 L407CDB : HK
80T 80T SB D104 L407CDB
D101,205 PRE-
HVC131 D105 L7091CER
DRIVE DRIVE FINAL
LOOP VCO T/R ANT ANT
FILTER Q9,Q10 BUFF BUFF AMP AMP AMP SW LPF
SW
2SK508NV(K52) IC102
Q13 Q14 Q101 Q102 RA30H1317M123 : K
2SC5636 2SC5636 2SC5108(Y)F 2SC5455-A RA60H13171123 : HK
IC5(1/2) TEMP
TC75W51FK(F) 80T DET
CV IC712(7/8)
PWR THP,THP2
IC5(2/2) M62364FP-F APC APC DET
TC75W51FK(F) DAC
VCO_MOD MP D107,108,109
D5,6 D19,20 50C /H_L IC101,103 HSM88AS-E
50R NJM2904V-ZB
HVC131 HVC131
Fin T/R BPF T/R /EVCS, SCK0, SDO0
SW X2 BUFF LPF
SW BPF
50C
Q6 Q208
SW 2SC5636 2SC5636
Q5 EMD9
/T_R Q2 DTA114YE
50C IC204
SPM5001
50R 50R XF202 50R L209,212,214 D207,208 80R D213,216
MCF L39-1498-05 D209,210 D217,218
1SV283F 1SV283F
IF IF 1st
AMP AMP MIXER BPF LNA BPF
Q204 Q205 Q210
2SC3356(R23) 2SC3356(R23) 2SC3357-A
150C 150C
IF IC IC712(4/8) IC712(3/8)
IC202 VAGC M62364FP-F M62364FP-F
TK10931VTL-G IC203(1/2) TV2 TV1
TC75W51FK(F) DAC BUFF DAC BUFF
RSSI IC205 IC206

IC203(2/2) LMC7101BIM5 LMC7101BIM5
TC75W51FK(F) /EVCS, SCK0, SDO0 /EVCS, SCK0, SDO0
50R
IF_DET IC705(2/2)
BUFF TC75W51FK(F)
IC705(1/2) Q702 D703
IC201 TC75W51FK(F) 2SC5383-T111 RB706-40
CF203 MCP6021-E/0T
SW BPF AMP DET BUFF ASQDET
Q701
SSM3K15TE(F)
RFAGC, ASSIST, DSW
T_R, W_/N, W_/V, /H_L
SCK1, SDO1
V, THP, THP2, RSSI, ASQDET

33A2 SB
VAGC, PLD, MPL, BLVL
SB
SPI
BUFF AMP
IC704
MCP6021-E/0T IC715 HOR CN705
LA4425A 6pin Option Connector
PA
33A2
IC711(1/2)
TC75W51FK(F) Ext SP JACK
R781 R780
100k
IC703(1/2) IC703(2/2) IC712(8/8) SPO J701

TC75W51FK(F) TC75W51FK(F) M62364FP-F E11-0425-05
LPF LPF DAC DEO BUFF VREF
100k
APC
APC MI2 VOLTEGE D905
/EVCS, SCK0, SDO0 SW OPT10 PROTECT 02DZ18F-X,Y
ME
AI IC710 Q708 DI
OPT10SEL BER_CLK VOLTEGE D906
TONE TC7W53FK(F) 2SA1832(GR)F LEVEL SHIFT 50C BER_DATA DEO
VREF AFO PROTECT 02DZ18F-X,Y
OPT9 Q709 TC7WBD125AFK
DTC114EE SURGE D901 D904
STSW IC711(2/2) IC712(5/8) Q710 PROTECT D907 D908
D911 D912
IC701 TC75W51FK(F) M62364FP-F DTC363EU IC517 AUXIO[1-9]
IC707 I2CCK I2CCK VOLTEGE
TC75S51FE(F) TC7W53FK(F) DAC MUTE I2CDT IC514 I2CDT I/O Expander AUXO1 INVERTER PROTECT
IC713
LPF TC7W53FK(F) AUXO2 Q901,Q902 D910,914
F SUM INAMT QSX6 02DZ18F-X,Y
/EVCS, SCK0, SDO0
/SCSW AO SB CN600-CN901 D909,913
IC513 50C D-SUB UNIT 1SS355
RXEO RXEI AMT TC7SET08FU-F
BEEP OPT6 /INT25P
D704,705 RD706F-40
Q704 2SC4738(GR)F TXD2
TXD2 BUFF
Q705 2SA1832(GR)F MM2
DTI LIMIT Q707
IC706(1/2) IC706(2/2) 2SJ243-A 25P_TXD2
TXO IC709(2/2)
TC75W51FK(F) TC75W51FK(F) IC708 TC75W51FK(F) MUTE MI2
TC7W53FK(F) IC516 RXD2
LPF SUM TC7WH126FU-F RXD2
SUM MUTE MI1 G_RXD2
TXI AI LEVEL SHIFT
Q706 50MC D506,507
/SCSW TONE 2SJ243-A 50MC 1SS416
MM
IC702(2/2) IC702(1/2) IC709(1/2) IC712(1/8) TXD0
TC75W51FK(F) TC75W51FK(F) TC75W51FK(F) M62364FP-F RXD0
RXD0
LPF LPF DAC TCXO_MOD CTS0
SUM IC712(2/8) RTS0
M62364FP-F IC518 CTS0
/EVCS, SCK0, SDO0 50MC RS-232C Driver
ESW, AMT, STSW, BEEP, TONE, /PRST DAC VCO_MOD
MM2, INAMT, /SCSW, RTS0, PBSHIFT ADM202EARNZ
IC712(6/8)
[0-3], IFC, TXC, RXC, SBC M62364FP-F /EVCS, SCK0, SDO0 TXD0
10SEL, /EVCS, SCK0, SDO0
DAC DI RTS0
25P_TXD2
/OVRB, /IGN, /PSW, /BINT /EVCS, SCK0, SDO0 50MC

G_RXD2
CTS0, RXD[0-3]
/INT25P IC515
LEVEL SHIFT
TC7WT126FU-F
PBSHIFT
26P_RD
26P_TD
SCRXD
IC512
OPT10
/PRST
OPT[1-8]
RXEO
RXD1
/PSW
OPT9
POW
RXEI
5V_1
TC7SET08FU-F
TXO
SPO
AFO
OPT11
MI1
80C
50C
CN556
CN557
TXI
DTI
ME
AO
SB
AI
TXD1
SCTXD
CN595 CN597
26pin Option Board Display UNIT
99
NX-700/700H
LEVEL DIAGRAM
Receiver Section
Radio Frequency 58.05MHz 450kHz
–121.5dBm –104dBm
–118dBm –120.0dBm –109.5dBm –112.5dBm –118.0dBm –72.0dBm
ANT
D213 RF AMP 1st MIX DBM IF AMP IF AMP FM SYSTEM IC
D216~218 Q210 D207~D210 IC204 XF202 Q205 Q204 IC202 CF203
BPF BPF ATT MCF CF
Buff AMP Buff AMP Buff AMP

Q9 Q10 Q208 CF
RX VCO BPF CF201
CF202
W: –85.5dBm W: –92.0dBm
0dBm 0dBm N: –83.0dBm N: –93.0dBm
SG input level for 12dB SINAD are obtained Measured by

connecting SG to each point via a 0.01μF capacitor.
Transmitter Section
5.2mVrms W: 244mVrms W: 241mVrms

4.0mVrms 48.2mVrms 69.2mVrms N: 122mVrms N: 121mVrms
MIC (MIC SUM1) (MIC SUM2) (ASIC) (MOD SMF) (MOD SUM)
6 7 6 1 K2 K3 6 1 2 1
IC709 IC706 IC510 IC702 IC709
MIC input : 3kHz DEV. (Wide), 1.5kHz DEV. (Narrow) at 1kHz MOD.
Transmitting frequency : Center frequency
100
NX-700/700H
LEVEL DIAGRAM
Audio Frequency
–82.0dBm –82.0dBm 186mVrms 226mVrms 226mVrms 96mVrms 4.00Vrms
IF AMP (EVOL)
IC201 (ASIC) (RXAF SMF) (RX SUM) VOL=20 (SP AMP)
E1 K1 3 4 6 7 13 14 1 4
IC510 IC701 IC711 IC712 IC715 J701
4Ω
AF VTVM
AF level obtained when the AF output level is adjusted for 4.00V/4Ω

with the front panel AF VOL control. Measured with AF voltmeter
connected to the external speaker jack, receiving a –53dBm SSG
signal modulated at 1kHz, DEV. WIDE 3kHz (NARROW 1.5kHz).
W: 358mVrms W: 222mVrms W: 222mVrms

N: 174mVrms N: 111mVrms N: 111mVrms
(EVOL)
DEV, BAL (VCO_MOD) (TX VCO)
1 3 6 7
IC712 IC5 Q10
30W : K
5.5dBm 6.7dBm +18.5dBm 50W : HK
D103 : HK ANT
Buff AMP Drive AMP Drive AMP Drive AMP Final AMP D104,D105,
Q13 Q14 Q101 Q102 IC102 D215
MOD TX VCO SW ANT Filter
Gate
bias D107 D108 D109
DET DET DET
VCTCXO PC DC DC
MB 19.2MHz MP AMP AMP
IC101 IC103
101
NX-700/700H
SPECIFICATIONS
GENERAL
Frequency Range........................................136~174MHz
Number of Channels...................................512
Zones ..........................................................128
Max. Channels per Zone.............................250
Channel Spacing .........................................Analog: 12.5/25 kHz Digital: 6.25/12.5 kHz
Operating Voltage .......................................10.8~15.7V
Operating Temperature Range ...................–22°F~+140°F (–30°C~+60°C)
Frequency Stability .....................................±2.0ppm
Antenna Impedance ...................................50Ω
Dimensions (W x H x D) .............................6.30” x 1.77” x 618” in. (160 x 45 x 157 mm)
(Projections not included)
Weight ........................................................3.03 lbs. (1.38 kg)
RECEIVER
Sensitivity ..................................................Digital @6.25kHz (3% BER): 0.20µV Digital @12.5kHz (3% BER): 0.28µV
Analog 12dB SINAD: 0.25µV
Selectivity ..................................................Analog @25kHz: –80dB Analog @12.5kHz: –70dB
Intermodulation Distortion .........................Analog @25kHz: –75dB Analog @12.5kHz: –75dB
Spurious Response.....................................Analog: –90dB
Audio Distortion ..........................................Less than 3%
Audio Output .............................................4W
TRANSMITTER
RF Power Output........................................1~30W: K 10~50W: HK
Spurious Response.....................................73dB
FM Hum and Noise (Typ) ............................Analog @25kHz: 50dB Analog @12.5kHz: 45dB
Modulation .................................................16K0F3E, 14K4F1D, 11K0F3E, 8K30F1E, 8K10F1E, 8K10F1D, 8K30F1D, 8K30F7W,
4K00F1E, 4K00F1D, 4K00F7W, 4K00F2D
Analog measurements made per TIA/EIA 603

KENWOOD reserves the right to change specifications without prior notice or obligation.
2967-3, Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan
P.O. BOX 22745, 2201 East Dominguez Street, Long Beach, Amsterdamseweg 37, 1422 AC Uithoorn, The Netherlands
CA 90801-5745, U.S.A.
Via G. Sirtori, 7/9 20129 Milano, Italy

6070 Kestrel Road, Mississauga, Ontario, Canada L5T 1S8
Bolivia, 239-08020 Barcelona, Spain

Rembrücker Str. 15, 63150 Heusenstamm, Germany
(A.C.N. 001 499 074)

Leuvensesteenweg 248 J, 1800 Vilvoorde, Belgium 16 Giffnock Avenue, Centrecourt Estate, North Ryde, N.S.W. 2113 Australia
L’Etoile Paris Nord 2, 50 Allée des Impressionnistes, Unit 3712-3724, Level 37, Tower one Metroplaza, 223 Hing Fong Road,
Bp 58416 Villepinte, 95944 Roissy Ch De Gaulle Cedex Kwai Fong, N.T., Hong Kong
KENWOOD House, Dwight Road, Watford, Herts., 1 Ang Mo Kio Street 63, Singapore 569110
WD18 9EB United Kingdom
A B C D E F G H I J K L M N O P Q R S
1 NX-700/700H PC BOARD PC BOARD NX-700/700H 1
DISPLAY UNIT (X54-3640-10) Component side view (J79-0157-29) DISPLAY UNIT (X54-3640-10) Component side view (J79-0157-29)
2 2
R988 R990 Ref. No. Address Ref. No. Address
1 6 R976 R989 R960 Q913 2K D924 5K
C956
C955
Q913
C963
R981
C949
C950
C951
C952
C953
C954
R991 C958
3 4 D908 4N D925 5N
R974
R968
R969
R970
R982
R967
R971
R972
R973
R962
LEFT RIGHT
UP UP
D911 4M D926 3M
PSW
3 D929 D936 D912 4H D927 6E 3
D914 3C D928 6K
D916
D917
D915
D922
D918
D926
D914 D915 3G D929 3D
R925
D916 3H D930 5P
C922 D917 3K D931 6I
4 D918 3L D932 6G 4
D908
D919 5H D933 6O
D911
D912
R923 C924
R924 C925
R922
D920 5G D934 6M
D919
D920
D921
D923
D924
D925
R904
R945
R921
C923
R920
D921 5I D935 5D
D922 3I D936 3P
5 D935 D930 5
D923 5L
DM/KVL
HK/RXD
MIC LEFT RIGHT
ME DOWN DOWN
J901
PTT/TXD
6 E 6
SB Component side
BLC/AFO
D927
D931
D928
D933
D934
D932
Layer 1
Layer 2
PF1 PF2 PF3 PF4
Layer 3
7 Layer 4 7
J79-0157-29
Foil side
8
DISPLAY UNIT (X54-3640-10) Foil side view (J79-0157-29) DISPLAY UNIT (X54-3640-10) Foil side view (J79-0157-29) 8
J79-0157-29
D913
Q902
R907 R963 IC905 CP909 IC901 9D Q905 12C

D910
D904 R966
L905
R952
R926
4 3
IC902 10E Q906 12C
Q901
5 4 R935 C927 R964

C913
C948 CP917
G
S
D
IC901 5 1
C962
R900
9 R902 1 8 C957 IC903 11F Q908 10E 9
R909
BLC/AFO 8 1 R992
R912
R911
C906 C907
C926 R934 IC907

Q904
R997
R927
SB C912 L902 C917

4 5
IC904 11G Q909 11B
4 3
R906
C911
E
C928 C921
R916 R917
100 76
48
25
IC908 1 IC905 9F Q910 10E
R996
C967
C946 R946
R947 R944
R936 75
C905
L904
C919
R915
C920
PTT/TXD 5 1
4 3
5 1
Q908
D906
C910
ME L901
C929
IC906 12F Q911 12B
C941
IC902
MIC R905 R914

R948 IC907 9F D901 10C
R918 R938 R939
R908
HK/RXD R913
10 10
D902
D901
D903
C918
R949
DM/KVL IC908 9F D902 10B
C908 C938
R901
IC909 12G D903 10B

IC911
X901
C909
Q910 C936
R919
C965
C947 IC910 12K D904 9B
GND 30
CN901 4 3 C961
IC913
SPO 2
R950
C915
IC911 10I D906 10D

RXD
5C
SHIFT
GND
GND
AFO
ME
GND
/PSW
SB
8C
SPO
SPO
C940
IC903
R937
R942
/PRST
IC912 13L D907 11D

29 GND
GND
GND
GND
GND
GND
L908
TXD
SPO
SPO
1 SPO
11 11
MIC
C939
NC
NC
SB
C916 5 1 R943
Q909
GND IC913 11L D910 9E
C942
D907 1 5 25 51
R958
C930
C903 C914 L903 IC904 LDM 26 50 Q901 9D D913 9C

C964
R957
R930
3 4
Q902 9E D937 12L
Q911
G
S
R940 TH901
CP912
D
R955 CP907 CP908 CP910

R929 R941 Q904 9E
R977
R978
R979
1 + C944
CN902
4 3
24
12 R953 12
R956
R954
R999
L906
C933
C945 11 10
R933
C934
2 5 4 IC909
/CS 20
C931 C932
IC906
V5 1
R965 5 1
V4
V3
V2
V1
VDD
VSS
VDD
D7
D6
D5
D4
D3
D2
D1
D0
/WR
AO
/RES
D937
IC910
Q905
Q906
C966
8 1
5 4
R986 Component side
+ C943 R928
IC912
+ C935 CN905
20 1 8 1 L907
Layer 1
R931 R932 C959 R998 C960 Layer 2
13 Layer 3 13
Layer 4
Foil side
14 14
TX-RX UNIT (X57-7380-XX) (A/2) -10: K -12: HK TX-RX UNIT (X57-7380-XX) (A/2) -10: K -12: HK
J701
Component side view (J79-0129-29 A/2) Component side view (J79-0129-29 A/2)
EXT. SP
Q403
2 1 R401 2
R403
C406
CN403
C410
2
R831 Ref. No. Address Ref. No. Address

R150 IC1 10L Q106 8K
IC2 9K Q201 10N
CN402
CN705
C806
GND
3 3
GMD
HOR
SPO
SPI
PA
SB
IC102 C188 IC3 9J Q202 10N
IC4 12J Q212 10O
6
1
+
5 IC5 11J Q403 2E

C805
C182 IC101 7J Q405 9B
+
IC715 IC102 3K Q406 9B
4 4
C807
C179
IC103 7K Q411 10B
C401
C198
TH102
1 R161 IC201 10N Q501 11C
+ 1 2 3 4
R826 D408 IC202 9O Q709 5D
C820
R823
IC203 10P D3 12J
C403
Q709
C125
IC205 7N D21 9K
C427
C428
L106
5 5
L401 C127
O C130 C173 IC206 7O D102 5I
C167
C133
+ C137 + L107 IC403 5B D207 10M
C135
D102
CN401
C139
G
C429
C473
IC403 C174
+B
L402
R127 L108 IC406 8J D208 9M
I C151 +
R125
R124
L403 L109
C165 IC407 12H D209 9M
6 R123 IC507 10C D210 8M 6
C141
C145
C148
C149
TH101
C163
D405
C124
R122
C422
+ D404 IC512 12B D404 6F
IC513 8B D405 6G
C432
F501
C421 IC514 9D D408 5G

F401 C419
C614 C615 C613 R131 R140 R273
IC515 8D D410 10B
C138 C157 C289 C298
7 7
R120
R126 C132
R139
R121 1 8 IC516 8D D411 10B
R284
R292
R288 R287
R286
R297 R296
R299
C616
IC103
R143
C162
C593 1 8
4 3
IC205
5 1
4 3
5 1
IC206
8
IC101
R132
R134 R921
R135 4 5 R145 IC517 9C D504 13B
R310
C592 IC518 C356
4 5 R147 R156
R117
C119
R142
R144
IC518 7D D506 8C
R115
R116
R130
G
R138
C156
R650 C197
16
R119 C126 D
9
D210
D508 Q105 R302
R562
R654 Q106 IC715 4B D507 8C
C299 R285
C293 R291
RS-232C
C618 C301
R565
R678 R644 R690 R689 R656 C612
C302
Q1 12K D508 8B
TTL
8 1 5 R658
R417
Q5 8
IC513 4 3 Q2 8J D509 9D
3 4 R651 D506 R637 Q3 S
R26
C595
C450 C434
C452 C437
D 6 1 L221
D511
G R82
D507
8
4 3
5 1
IC406
D510 Q3 8J D510 8D
C222
C438
IC516
IC515
C194 C193
R84
R83
R842 R640
Q2
C296 R290
C357
C297
D
C594
R333 Q5 8K D511 8C
R669
R668
R667
R666
R665
R664
C435 S
C221
C229
D509 L31 C195 G Q15 D209 C223
C447
C471 D21 R315
R415 6 1 R353
C224 C212
R674 C14 C295 C294
Q15 9K D512 9B
R641
R639
R642
R638
C190
L1 1 24
R673 7 L32 13 L33
R223 R227
C17
Q405 18
C232
R228
R652
R636 R210
R648 R646 C596
24 R80
R216
R11 12
R413
R12
C16
IC517
19
R9
R672 R338
Q105 8K
L219
9 C19 C11 C8 9
R6
C218
IC3
D512 C13
X1
R422 R426
IC202
4 3 19 R14 C20 C351
C219 C227
12 5 4
R10 R334
C15
6 1 13 18 IC514 C21 25 1 7 C288 R283
1 6
3 4
IC2
8 1 R15 R7
L223
6 C220 C233
R671
R670
R663
R662
R661
R660
R659
Q406 CD201 C226

D208
C353 C352 R226

R331 R215
R21
R23 C22
C27
C25
C591
C23
R18 C24
L35 C7 Q212 R329 12 13 R232
C291 C290
R5
Q411
R239 R224
C6 R86 4 3
D411
C28
C358
L34
C230
R218
4 3 R22 6 1
C527
R575
C225
R444
C336
R225
R576
R579
R582
R586
R585
R588
R590
R593
C534
R1 C3 L218 C202 C201
C12
R2
C1
R88 R3 C2
C5
R209
5 1 R330
R433
C354
R25
+ C32
R328
R445 R37 R36 R30
BATT CHK
IC507
Q201
C355 5 4
10 R229 10
4 3
5 1
D410 C213
C228 R219
C286 R282 IC203
IC1
R236
C235
R220
R31
C287
C214 Q202
+ C34 8 1
R231
C334
D207
R212 R211
R548
IC201
1 5
3 4
C237
R245
C244
L506 C231
19
C285 C284
1
CF203
R922
+ C35 R4
R222
C9
R583 R589 R918 CV R221 RAGC
CN549 R919 R29 IFDET
R580 R592
L217
C47 R48 R44 R47 C31
L512
CN405
R578 R595 VAGC

C543
C546
C562
C565
C568
C570
C572
C574
C576
C578
20
C54 C46
C282
2
R35
R27 R28
L508 R49 LO
L511 5 4
R603
L903
OPT6 25
R51 IC5 R276

OPT1 1
C560 8 1
R52
26P_RD
OPT10
AI
GND
OPT9
OPT8
OPT7
TXO
RXEI
C559
11 11
R274
R275
R278
C540 C55
C555
C556 C548 C547 C552
C554 C539 Component side

C551
R506 CN595 BPF GND

C538 R352
C817
26P_TD
R342
OPT11
Q501
RXEO
1 6
3 4
2 OPT3
OPT4
OPT5
OPT2
Layer 1
GND
C29
R248
C245
C37
DTI
TXI
AO
R85 C26 R20
R634
C577 26
Layer 2
R34 R33
C33 R38
R523 C18
IC512
Q1 R17
4 3
5 1
4 3
5 1
C545
C553
C561
C563
C566
C567
C569
C571
C573
C575
C579
IC4
C550
D3
C558
L522 R684 C537 Layer 3

R13
R89
C557 4 3
C590 C515 L517
C549
IC407
12 12
C439
5 1
Layer 4
C585 C584 C448 Layer 5
R534
DGND
C449 C440
L509
L510
C588
C589
Layer 6
R633
C582
C586
R630 C581
C580
R632 D504
C825 C587 C583 Foil side
BSC1 BSC0 FLDM 33V 5V_2 DGND
30
1 (DM)
GND
RXD
TXD
NC
5C
SHIFT/MODEL
GND
(LCDDO)
(LCDDI)
(LCDCB)
AFO
GND
ME
MIC
GND
GND
PSW
NC
SB
SB
8C
GND
SPO
SPO
SPO
SPO
SPO
SPO
RST2(LCDCLK)
13 13
CN597
26P_RD
26P_TD
OPT10
OPT11
AGND
RXEO
RXD2
TXD2
OPT1
OPT3
OPT4
OPT5
OPT8
OPT7
OPT2
OPT9
OPT6
POW
5V_1
RXEI
TXO
DTI
TXI
J79-0129-29 A/2
14 14
TX-RX UNIT (X57-7380-XX) (A/2) -10: K -12: HK TX-RX UNIT (X57-7380-XX) (A/2) -10: K -12: HK
Foil side view (J79-0129-29 A/2) Foil side view (J79-0129-29 A/2)
2 2

IC204 11F Q13 10I D14 11I
C809
IC401 7M Q14 10I D15 11J L116
C811 C810
R411
C417
3 IC402 6N Q101 7I D16 11I R410 3
D406
IC404 6P Q102 7J D18 11J
C184
D401 Q401
R404
C405
C186
IC405 5N Q203 8E D19 9I
C178 R149 C183
R402
D403
Q402
L115
R408
IC408 5M Q204 9D D20 9I
R409
C475
IC409 7N Q205 10D D101 9H D109
C445 L405 G R825
4 4
L114
C801
IC410 12J Q208 10G D103 5F C446 +
C411
R407
Q404 D C802
C176 C415
IC501 12P Q210 7G D104 6F D409 D407
R828
Q710
R448
C468 S
IC502 10Q Q401 3P D105 6E C177 C443 R430 1 6 Q414
R827
C804
D108 C454 IC405
C441 Q413 C803
IC503 12Q Q402 4P D107 6D 3 4
R431
C175 L404
R423
C474
R424
CN511 CN513
Q408
R432
R148
IC504 10N Q404 4P D108 5D
C431
C430
D412
5 5
L113
IC408
4 3
5 1
CN517
Q407
R440
IC505 10P Q407 5P D109 4D
CN542
C463 R447
C136
C134
Q416
C456
4 3
6 1
IC506 13P Q408 5P D201 10E D103 R419 R418
1
C453
IC402
C425
IC508 10O Q409 7O D202 10F
L112
R437
C171
5
L110
D104
IC509 9P Q410 7N D205 9H C169 C409 C426 C433
R146
D107
6 6
O
IC510 12O Q412 6N D213 7E C413 C424
I
+
L111
C158
C154
R446
C436
IC404
IC511 9O Q413 5P D215 7D
C172
D105
R137
R154
C170 Q412
R428
C164
IC701 12M Q414 5P D216 7E C159
R429
R425 R420
R141 C155
R421
G C597
D
IC702 8N Q415 7O D217 7E
G
R449 S
Q410
NC/RSSI 1
CN502 CN504 CN508 CN520 SB
Q409 SB
IC703 12L Q416 5N D218 7E R405 SB C611
C420 R406
D218 D213 SB
1 5
IC401
3 4
SB
7 4 3 7
C455 C442
SB
C451 C444
IC704 10M Q417 12I D401 3O AFO C610
C342
C311 R107 C105 E C C118 L104 L105 Q415 DI/RTS
R105 Q101
C341
IC409 50C C609

R304
C120
C115 R114
R103 C104 D704
C328
C101
C103
R101
C102
D216 R319 D217 C121 Q704
R113 L102
Q102 GND
C123
C128
IC705 12L Q701 12K D403 4P
C111 L101
L229
R294
R303 R784
DEO
C608
R102
R106
R104
L222 R109 C109 B E C122 5 1 MI2
C765
R306
D215
C338
R341
C337
C750 ME
CN600
C Q210
C117
L230
R340
L103
GND C607
R347
C316 R110
C112
IC706 8M Q702 11L D406 3P
C335
L220
C106
C762
C116
R111 RXD0
C308
R112
C304
R108
R322
C107
R339
C110 C108 C744 AUXO2 C606

B
R804
E
C329 TXD0
C766
R722 R716 C707 C729 R749 Q705 AUXO1 C605
C742 R753
IC707 12M Q703 12M D407 4N C300 1 8 R767 C751 AUXIO9/CTS
R305 R724 R787
C721
C787
R813 C791
C794
1 8 IC708 AUXIO5 C604
C736
R748
R768
C763
4 5 AUXIO8
R789
C315 R307 R301 R725 IC706 D705 AUXIO4 C603
R765
IC708 8N Q704 7P D409 4N CN505 CN503 C715
4 5
R759
TXD2/AUXIO9
AUXIO3 C602
8 8
C782 R796 R793

RXD2/DI R815
CN527 C748 R766 C770 AUXIO2 C601 C793 R809
R745
IC709 8O Q705 8P D412 5N AUXIO1
R202
L202 C207
C757
R773
C600 R812
Q707
R739
R741
1 8 C773 AUXIO7/BER DT
R779
R786
C764
L201 C216 C211 Q203
G
S
AUXIO6/BER CK 30
D
C706 IC709 G
C783 R797
C784 R798
C599
C206
R816
C77 5 4
C217
IC710 11M Q706 8R D501 13O
C61
C49 C53
C48 C815 4 5 D
R714
L16
R705
C712
L204 R774
L8
R61 IC702 C598 S Q706
R332
R46 R710 8 1 R731 R775 R801
R63
L206 C215 C210 R205 C208 L12 C816
IC711 11L Q707 8R D502 13O R235 C66 C57 R57 D706 C720 R806 C795
R346
R213
C701
D20 C776
C238
R234
D6
R833
R835
R834
L205 C234 C348
C78 C777
IC712 9L Q708 10L D503 9O R822
C62
C52
R79
L18
C239 C68 R59 R39 CN509 CN506
C75
C73
R45 L7
R238 C71 C813
C203
L20
IC713 11K Q710 5Q D702 11L
NARROW
9 9
R240
C44
CF202
D19
12
1
L36
R75 R76 C97
R693
R544
L502
C518
C69
R93 R92
C56 C63 R685
C65
Q204
R557
R558
R538
R539
R553
C516
R540
R541
R695
R696
C517
R554
R694
C790
C36 C45
D707
L15
D101
Q6
C242 R56
IC714 11L D5 9J D703 11L C96 Q7
1
R574 R584
CN611
IC509
R77 R78
C732
C333 R327
L24
R60
D5
C263
C261
L208 C240 IC712 IC511

C95
R74
C83 R686
R204 C204
C332 R314
R733 R552
L28
L503
R915 C536
C789 R821
X501
C93 R71 C92
R264
C86 R68
Q6 9I D6 9J D704 7O
C529
R243
4 3
5 1
C532 C531 R542
8
R242
C359 R343
D503
R207
R537
D205
C264 4 3 4 3
R62
R73
R72
C91
C94
L27
R734
13
24
L207 R201 Q13 S Q11 R818 R536 R543
C90
R69
C98 D IC704
R596 R594
Q7 9K D7 11I D705 8O C243 6 1
C89
R66
D202 R266 G C522 L905
CN516
Q708
Q14 C799
R820
D201 R70 5 1
CN540
R244
R208
R265 Q12 IC508 R581 R533 C513
X502
R817
R247
1 5
Q9 10I D8 11J D706 9L
Q205
Q208
C714 R717
C710
R268 C774 IC505 R532 R531
R836
Q10 1 6
R545 C521 L523

Q9
L521 R561
R325 C331
C205 R206
R726
C725
R730
C266 3 4 R529
R313 C330
R324 R203
C528
R698
C514
C530
R67 C38
D
C268
10 10
G
IC502
Q10 10J D11 11H D707 9M
R802 R799
C785
R846
C80 C79
3 4 R527
C269
L211 R567
CF201
C246
WIDE
G C85
D
R800 IC504
S
R516
L22
R795 R790 R560
R794
R572
R267 R269 S R805 R528
Q11 10K D12 11J
L23
5
C270 R803 R814 C779 C511
CN510 R697
L26
C87 R65 R511
CN612
C88
R64
L213
R512
C84
C272 R520
R780
C778
C767
C81 C82 R810 C792 R792
C788
Q12 10J D13 11H C509
R677
R629
R687
R688
R625
C621
C544
R624
C814
8
5
C542 +
5
C275 C72 C70 R791 R521
R819 C798
R785 C775
IC713
IC711
IC710
L215
L25
C283 R279
C64
IC714
4 3 R507
R781
R525
R524
C76 D18 C769
CN512
CN543
C67
C280
R281
R277
R280 5 1 C541
R701 R706
R569
R680
R616
R615
R617
R611
R612
R618
R620
R619
R256 R250
4
L17 C761 R788
C267
R320 L19 R807 R808 C507
C754
D13
D11
CN507
D15
D12
L212 D16 C512

D14 C797 C796 C786 R783
C745 R764 R776

C749 C752 R777
R772 C753 R778
C768
R510
C508
R841
C503
R556
R501
C506
C505
C824
C504
Q702
R845
R770
11 11
C279
C252
R782
R271 C42
D8
C740 R515 R514

C39
R577
R91
L41 C41
C262
D7
C51
L13
R90
L10
L11
L14
C741
R747
C738
R750
D703
R42
R720
L2
Component side
L3
IC204 L4 R843 R771 R606

L40 C50 R43 C43
R727 C737
R751
C818
C718 C734
1 6 D702
C247
R691
L209
L214
C747
Layer 1 3 4 C719 R755 R605
R769
XF202 G
IC510
R257 R321
R261 1 8 D R763
C722
R729
S R692
Layer 2 IC705 Q703 C746
R760
4 5 R607
R263
C260
R270
C276
C716
C265
C259 C462 C460
R758
C743
R746
C711 C731 R752

L210
R587
R441
R443 C461
R438
Layer 3 R709
1
R721
R707
R761
IC707
R450
5 4 R608
C724
C821 C502
R837
C256 R756
TH701
R762
C464 IC410
C458
C457
R610
12 Layer 4 C501 12
8
R838
IC501
IC503
R442 C459 +
Q701
8 1 R503
D
L904 L501
G
S
C717 R738
R728
C726
R732
R704 R708
C465 C735 R568
Layer 5
R703
R435 R434 R718 C723

R436
C730 R744
R591
R597
R623
R628
R627
R621
R622
R676
R602
R604
R614
R715 C705 R740 C533
3
1
C467
Q417
C727
1 8
R713 R551
C702
L406 4 3
Layer 6 R712 IC703 R737
CN614
4
5
C535
C466 4 5 5 1 C708 R681 C520
C709
C620
IC701 R683 1 4
R600
R601
R599
R598
Foil side R682
L518 L507 2 3 C523 R509 R504 R522
D501
D502
IC506
13 13
J79-0129-29 A/2
14 14
A B C D E F G H I J
TX-RX UNIT (X57-7380-XX) (B/2) -10: K -12: HK
Component side view (J79-0129-29 B/2)
2
R902
R903
R911
R912
C911
C912
R904
C913
C914
R906
C916
R907
C917
R908
C918
C919
R909
C920
R910
R905
C921
R913
C909
C910
C923
25 14
4
13 1
C905 C906 C904

Component side D906
D905
5
L902
L901
Layer 1
C901
C908
J79-0129-29 B/2 C915 C903
Layer 2 C902
Layer 3
NC/RSSI 30
AUXIO6/BER CK 1
AUXIO7/BER DT
AUXIO1
AUXIO2
RXD2/DI
AUXIO3
TXD2/AUXIO9
AUXIO4
AUXIO8
AUXIO5
AUXIO9/CTS
AUXO1
TXD0
AUXO2
RXD0
GND
ME
MI2
DEO
GND
50C
DI/RTS
AFO
SB
SB
SB
SB
SB
SB
Layer 4
Layer 5 Ref. No. Address
6
Layer 6 D905 5G
CN901
Foil side D906 5H
7 TX-RX UNIT (X57-7380-XX) (B/2) -10: K -12: HK

Foil side view (J79-0129-29 B/2) R901
R914
8
Q901
Q902
B
C
C
B
C
C
C907
C922
C
C
C
C
E
J79-0129-29 B/2 D910 D914
9 D909 D913
D901 D902 D903 D904 D907 D908 D911 D912
13 1
J901
25 14
10
Component side
Layer 1
Layer 2
Layer 3
11 Layer 4
Layer 5
Layer 6
Foil side
12
Q901 8G D904 9E D911 9F
Q902 8H D907 9E D912 9F
D901 9C D908 9E D913 9H
13 D902 9D D909 9G D914 9H
D903 9D D910 9G
14
(K) R : 13.57V (HK) R : 13.6V HD2 HD2 HD2 HD2 HD2 HD2 HD2 HD2
T : 13.14V T : 12.57V
∗IC102 2 2 2 2 2
LCD
X2_CLKIN X2_CLKIN X2_CLKIN X2_CLKIN R572 22 X2_CLKIN X2_CLKIN X2_CLKIN X2_CLKIN
TH1
DRAINBIAS
ANTENNA
RFoUTPUT
GATEBIAS
∗L401 SB SB
RFINPUT
D7,11,13,14 R : 3.46V R : 2.15V T/R R : 0V SWITCH SB
BUFFER AMP RF
VCO T : 0V ASQDET ASQDET
C93
T : 4.23V SW T : 4.94V
5p
PRE-DRIVE AMP
15M
FREQUENCY (RF)
33A-2
33BU
15M
33M
33M
33A_2
33A_2
33A_2
80C
TH100
50C
50C
50C
33M
33M
33M
50R
RX VCO
33A_2
33A_2
33A_2
33A_2
∗D103
33GPS
R67
C124
470p
R122
R826
-t °
100k
Q9
3.3k
10k
L402 CONTROL IC715
IF_DET
50C 50C 1.12V D101 L407CDB R603
GND1
GND2
CN401 +B 2SK508NV(K52) 0.74V Q14 C98 R77 C102 R103 C104 R107 C105 C109 3.29V LA4425A
0.01u
150 R825 C801 C802 R828
C540
C538
C539
C537
33A
OUT
VCC
0.1u
0.1u
1000p
R42 L3 C50 R90 D11 C67 L112 L113 L114 L115
1u
2SC5636
C38
1
ANT R720 R577 0 10k 1u 1u 0
IN
L403 (K) (HK) IC405 Q5 R70 C91 C94 10p 0 HVC131 1000p 18 470p 180 470p 33p 3 3 3 3 3 3 3
C421 0.047u
TX TX L104 D104 5T 5T 5T 5T
C419 1000p
RF DRIVE AMP C165 R150
C427 470p
C428 100p
1000u25
R79
4.62V 13.54V
100n
10u
22ZR-10D
LT1616ES6-PBF 0 470p 0 33p
2.2k
F401
1SV282-F
4 4 4 4 4 4 4
R75
R : 13.57V R : 13.6V EMD9 OPT10 OPT10 OPT10 OPT10
L28
56
∗R124
DSA3A1
1SV282-F 33n /INAMT /INAMT
C401
Q101 100k 1k
C403
470p
1
5A
+
5
2
4
C79
R827
150k 22p 15p
3.3k
L101
D405
D404
R102
R109
R104
T : 13.14V T : 12.57V 5 5 5 5 5 5 5
8p
4.7k
120p 0
D13
R78
82n
1.34V
270
270
470
4 3 2SC5108(Y)F Q102 C118 L105 L407CDB
∗C163
∗C171
C18
C16
U18
U17
U16
C17
1SV325F
R13
B16
B18
B17
K14
R726
∗C182
∗C173
∗C179
∗C186
∗C188
A18
A17
P12
P13
∗C167
∗C174
∗C177
R : 0V
V18
V17
V16
T17
T16
F15
J14
R : 4.96V
L116
M1
9.5T
G5
G4
∗R125
470p
N4
C5
C3
U2
U1
H5
U3
H4
C4
D5
D6
D4
D3
B2
B1
B3
SHDN FB
18p
K5
K4
39n
A3
A2
A1
A5
P7
P8
10
V2
V1
E6
E5
E4
F3
T1
F5
T3
F4
T2
L1
L3
C88 2SC5455-A 56p C121 C135
J4
J5
C77
470p
11 11 11 11 11 11
100p
5.01V 0.96V
9p
TX TX 3.28V BUFFER AMP 0V
/HRDY
L404
/DRST
/CS0
C42
/HINT
C48
/CS2
/RD
/RD
1.99V T : 1.60V
L110
SCTAM1
T : 0.78V
D7
5 2
10T
3.3k
R72
1.22V
100n
/INAMT
1000p
47u25
4.79V (2nd IF DET) 2nd IF BUFF
L27
17.5n
R61
C805
C807
470p
220n
220n
R46
VIN GND E12
22k
22k
+
C72
C73
R60
39n
3.83V 8.00V 7.97V
10p
L20
L10
L19
L23
56k
NC21
NC11
NC1
ADC1
DGND11
0.5p 9p 470p
1000p
1000p
AVCC1
1000p
3
NC30
NC20
NC10
0.94V 7.70V
NC29
NC28
NC26
NC23
NC19
NC18
NC16
NC13
NC36
NC9
NC8
NC6
NC3
NC25
NC15
NC35
L508
NC5
D409
NC22
NC12
MICIR
NC2
NC27
NC24
NC17
NC14
NC34
DGND10
NC7
NC4
AGND9
AGND8
AGND6
AGND3
DGND13
DGND9
DGND8
DGND6
AGND5
DGND15
DGND5
AGND2
DGND12
AVCC10
DGND14
AGND7
AGND4
DGND7
DGND4
IFIR
AVCC9
AVCC8
AVCC6
1
AVCC5
AVCC2
Q13 Q910
AVCC4
C803
C804
2
1000p
CN402 6 1 DGND3
L502
L503
C95
R64
R74
2 2 2
270
270
C96
SW BooST 50M RX 2SC5636 1.76V R569 E11 SQ VOLTAGE 6.38V 12A02CH LCD KEY
1SV282-F
∗R123
∗R127
C122
C120
C123
C128
C137
4
R114
L102
D6 L12 D20 3.28V 8C
0.01u
C49 C57 C66 C68 R662 470k
22p
22p
33p
33p
DGND2
68n
18p
330
22
C80
C84
4
∗C169
∗C176
∗C184
1SS388F A4 C729 CONTROL
C454
470p
R430
220n
A16
8p
120k
/PCS_RF
Q710
C158
C154
/BER_EN
1/4W
1/4W
470p
D14
R137
R154
100p
E10
L13
R823
330u16
XTALI
240
240
0.01u
C468
SURGE REVERSE 0.1u
C806
68n 3 5 DGND1
+
3.3u
D921
D931
R111
470p 2p 470p 1000p R915 DTC363EU
1000p
D919
D923
D933
D925
R112
R938
HVC131 HVC131 B4
L25
R841
2.7k
R663 470k
C106
C508
C107
1.8k
470p
470p
1000p
R510
R515
R105
R106
R108
4 4
470k
SDO0 LCD
100k
10k
R931
5
R932
ABSORPTION PROTECTION PLL FIN D702 TX/RX LED
C430 4.7u
C431 4.7u
33k
100
10k
L40 C547 0.1u R755
R71
C92
BUFFER AMP 1.48V 3.31V XTALo R : 0V 1.63V
470
L5 7.27V
560
100
0 4.7k
R73
33M_4 33M-4
0
10k
C61
5.6n
5.6n
C820
C53
22p
2.03V 5 BACK
18p
L405
L16
R101
C112
470p
R113
T/R SW A10 DVDIo7 AF TX/RX LED (BUSY)
L8
MCP6021-E/OT
3.3k
PLL FIN PLL FIN (VCO) T : 1.63V SCK0
1u
VIN-
VDD
IC706
D10
D12
D0
D14
D8
D3
D6
POWER POWER POWER
D5
D2
D2
D7
D7
22
B30-2281-05
B30-2281-05
B30-2281-05
B30-2281-05
B30-2282-05
B30-2282-05
32K 32I C548 0.1u 10k 50C LIGHT
HVC131
2.30V 3 P6 HSC119 MUTE (TX)
/RES
R431
Q6 Q709
C115
470p
T/R SW T/R SW
VDD
VDD
D TC75W51FK(F)
/WR
470p
VSS
DET DET DET A12
18k
/CS
C39
D205
22uH D8,12,15,16 R : 0V T/R 3.31V DVDIo6 MIC AA /EVCS /INT25P SW
HSM88AS-E
HSM88AS-E
HSM88AS-E
D0
D1
D2
D3
D4
D5
D6
D7
2SC5636 DTC114EE
A0
V1
V2
V3
V4
V5

NX700 (H)

Uploaded by

Copyright:

Available Formats

NX700 (H)

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

NX700 (H)

Uploaded by

Copyright:

Available Formats

VHF DIGITAL TRANSCEIVER

Key top Panel assy

4-3. Radio NOTE

4-4. DC Power and wiring

5. INSTALLATION PLANNING – CONTROL STATIONS

5-2. Radio location

License and frequency allocated by FCC Frequency range RF power Type

Are you using YES See page 9.

Are you using YES See page 7.

Are you using YES See page 10.

Are you using YES

Are you using YES

2. How to Enter Each Mode Notes:

4. Panel Tuning Mode Note:

1-1. Connecting the KCT-46 cable to the transceiver

FIg. 2-1 FIg. 2-2 FIg. 2-3

4. Voice Guide & Storage Unit

Note: You must setup using the KPG-111D. : Cushion

Note: You must setup using the KPG-111D.

TX-RX unit (A/2)

■ FINAL shield case (F10-2489-13) installation

■ Power supply cable installation procedure Fig. 4-2

Fig. 7-2 Fig. 7-3

■ Removing the lithium cell (W09-0971-05)

1st MIX MCF SP

Base band Circuit

Fig. 1 Frequency configuration

3. Receiver System 3-2. First Mixer

–118dBm –120.5dBm –114.5dBm –112.5dBm –104dBm

BPF BPF MCF

Buff AMP Buff AMP Buff AMP

3-4. Audio amplifier circuit 3-5. Squelch Circuit

IC705 (2/2) Q702 D703 IC705 (1/2)

SW AGC SW AMP LPF IC510

LPF LPF AMP IC712 AMP VCTCXO

IC702 IC702 IC709

MOD TX VCO SW ANT Filter

IC405 Q412 50MC TXC

IC408 33A RXC

8. Signaling Circuit 9. Compander Circuit

8-2. Decode (QT/DQT/DTMF/2TONE/MSK)

Q105 Transistor SW (RF Power H/L) Variable Capaci-

D501,502 Diode Line Protection D912 Diode Line Protection (AUXIO5)

• Tolerance (More than 10pF) (Less than 10pF)

4 2A B09-0681-03 CAP (KAP-2)

- G10-1322-04 FIBROUS SHEET (PANEL-SP) C919 CK73HB1H102K CHIP C 1000PF K

28 2B G13-2047-04 CUSHION (DC SCREW) C930 CK73GB1E105K CHIP C 1.0UF K

33 2B G53-1643-04 PACKING (DC CORD) C936 CC73HCH1H100D CHIP C 10PF D

A 2B N09-2292-05 HEXAGON HEAD SCREW C966,967 CK73HB1H102K CHIP C 1000PF K

C13 CK73HB1E103K CHIP C 0.010UF K C97 CK73HB1A104K CHIP C 0.10UF K

C19-23 CC73HCH1H101J CHIP C 100PF J C104-107 CK73HB1H471K CHIP C 470PF K

C31 CC73HCH1H101J CHIP C 100PF J C118 CC73HCH1H560J CHIP C 56PF J

C36 CK73HB1H102K CHIP C 1000PF K C123 CC73HCH1H330J CHIP C 33PF J

C42,43 CC73HCH1H101J CHIP C 100PF J C128 CC73HCH1H330J CHIP C 33PF J

C52 CC73HCH1H390G CHIP C 39PF G C137 CC73FCH1H180J CHIP C 18PF J

C57 CC73HCH1H020B CHIP C 2.0PF B C148 CC73HCH1H101J CHIP C 100PF J

C65,66 CK73HB1H471K CHIP C 470PF K C162 CK73HB1H821K CHIP C 820PF K K

C71 CK73HB1H471K CHIP C 470PF K C167 CM73F2H430J CHIP C 43PF J K

C77,78 CK73HB1H471K CHIP C 470PF K C171 CC73GCH1H0R5B CHIP C 0.5PF B K