Cam & Groove Couplings: Standard Federal Mil A-A-59326A

a1-c&g 9/18/07 1:46 PM Pagina 1
CAM & GROOVE COUPLINGS FED MIL / EN / DIN

A.1.
STANDARD
CAM & GROOVE COUPLINGS

Federal Mil A-A-59326A
The standard for cam & groove couplings is based on the US Military
Specification Mil-C-27487. The Mil-C-27487 specified the casting methods,
materials, dimensions, tolerances, pressure ratings and inspection proce-
dures. In 1998, the original Mil-C-27487 specification was replaced by a new
Federal Military standard: A-A-59326A. Federal Mil A-A-59326A guarantees
interchangeability of couplings designed to the same specification.
Interchangeability with other brands

Between manufacturers cam & groove couplings are interchangeable with
the exception of 1/2" (12.7 mm), 5" (127 mm) and 8" (203.2 mm).
The A-A-59326A Mil-specification does not apply to 5" and 8" cam & groove cou-
plings, due to the presence of two versions of cam & groove couplings in today’s
market.
FED MIL / EN / DIN

Limitations: Hose shanks with larger serrations are not designed to be
assembled with a ferrule or sleeve. Hose damage can result if they are
swaged. The larger shank serrations will cut into the inner wall of the hose
resulting in leakage or permanent hose failure.
N.B.: Cam & groove couplings must never be used for steam or compressed air
applications.
EN 14420-7
The European standard EN 14420-7 was approved by CEN in September

2004, and was applied to cam & groove couplings manufactured to American
“military specification” MIL-C-27487 / A-A-59326A. This American standard
does not apply to the hose connection side, but only to the coupling side.
Cam & groove couplings produced to EN 14420-7 are interchangeable with

those produced to the original MIL-C-27487 standard, but differ in terms of
hose tail design, thread, part number etc. A flat thread seal has been added
to the female threaded parts, and a smooth hose shank complying with
EN 14420-2 / DIN 2817 has been added for assembly with RK safety clamps
complying with EN 14420-3 / DIN 2817.
N.B.: European standard EN 14420-7 replaces DIN 2828 but does not replace
MIL-C-27487 and Federal Mil A-A-59326A.
DIN 2828
Couplings produced to DIN 2828 are interchangeable with those produced

to the original MIL-C-27487 standard, but differ in terms of hose tail design,
thread, part number etc. A flat thread seal has been added to the female
threaded parts, and a smooth hose shank complying with DIN 2817 has been
added for assembly with RK safety clamps complying with DIN 2817.
A.1.1
a1-c&g 9/18/07 1:47 PM Pagina 2
PRODUCT RANGE
OPERATION
To connect
1. Open the coupler by pulling back the locking lever above the cam handles, whilst rotating the handles
away from the body of the coupler.
2. Insert the adaptor into the coupler
3. Close the coupler by rotating the cam handles towards the body of the coupler. Locking occurs when
the cam handles are closed. The coupler is properly closed when the locking levers on both the cam
handles assemblies are flush. For extra security, insert safety clip through the holes above the cam
handles. Line pressure, which moves the coupler and adaptor independently, increases the pressure
on the cam face, ensuring increased locking leverage. Under normal conditions, safety locks are not
necessary, but are recommended. The adaptor and the coupler are designed to minimize the fluid
turbulence and the abrasion from dry products when connected.
To disconnect
4. Be sure that the hose-coupling connection is depressurized before disconnecting.
5. Open the coupler by pulling back the locking lever above the cam handles, whilst rotating the handles
away from the body of the coupler.
6. Remove the adaptor from the coupler.
7. Close the coupler by rotating the cam handles towards the body of the coupler. Locking the coupler
when not in use will help protect it from accidental damage.
FEATURES
6 1. Stainless steel triangular handles, pin, ring and safety pin are standard on all
7 material versions. Handles manufactured by investment casting.
1
2. Holes for safety pin inserts
2 9 3. Earthing lug
4 8 4. Reinforced coupling section for increased mechanical strength
1
5. Long hose shank to ensure secure fixing
6. Marked with cam & groove type
1 7. Marked with diameter

8. Marked with standard compliance: MS (Military Specification) or DIN (Deutsche
1 Industrienorm)
9. Marked with material identification: stainless steel, brass, bronze, aluminium,
5
polypropylene
10. Seals are available in NBR (standard), EPDM (for polypropylene), PTFE, CSM,
FPM, FEP/Silicone, PTFE/EPDM and PTFE/FPM
11. Safety couplers are available with monoblock safety boddy
3 10 11 12 12. Coupling insurance by brand name LMC-Couplings®
APPLICATION
Cam & groove couplings are used for hose-to-hose or hose-to-pipe / manifold connections for the transfer of liquids or dry bulk products
with the exception of liquid gas and steam.
A.1.2 Chapter A: Quick couplings

a1-c&g 9/18/07 1:47 PM Pagina 3

A.1.
PRODUCT RANGE
WORKING PRESSURE

INCH 1/2" 3/4"-2" 2.1/2" 3" 4" 5" 6" 8"
Working pressure Bar Psi Bar Psi Bar Psi Bar Psi Bar Psi Bar Psi Bar Psi Bar Psi
Brass 11 150 18 250 11 150 9 125 7 100 5 75 5 75 - -
Bronze - - 18 250 11 150 9 125 7 100 - - - - - -
Aluminium 11 150 18 250 11 150 9 125 7 100 5 75 5 75 5 75
Stainless steel 11 150 18 250 16 225 14 200 7 100 7 100 7 100 3 50
TEMPERATURE RANGE
The working pressures shown above refer to ambient temperatures using elastomer seals. Higher temperatures and / or PTFE seals will
reduce the rated coupling pressure. In the case of polypropylene, the maximum working temperature is 70°C / 160°F, at which
temperature the working pressures shown above should be reduced by 40%.
Hose, coupling, seal and assembly method must be chosen in relation with the desired application and temperature range.
FED MIL / EN / DIN

MATERIAL
Coupling
LMC-Couplings cam & groove couplings are available in the following materials:
Stainless steel: ASTM A666 grade 316 / 1.4401

Brass: ASTM B584 grade C85700
Bronze: ASTM B584 grade C84400
Aluminium: ASTM B85 grade 380
Polypropylene: LMC’s polypropylene cam & groove couplings contain 25-30% fiberglass reinforcements
Production method
All sizes of brass and bronze cam & groove couplings are shell-moulded or sand cast.
The type of aluminium is a sand cast 713-T5 alloy, which can be anodised if required.
Stainless steel couplings are investment-cast in a range of common sizes and are electro-polished for clean applications.
The stainless steel quality for cam & groove couplings is standard AISI 316 / 1.4401
Polypropylene couplings are made from polypropylene reinforced with 25%-30% acid-resistant fibreglass.
Chapter A: Quick couplings A.1.3

a1-c&g 9/18/07 1:47 PM Pagina 4
CAM & GROOVE COUPLINGS FED MIL / EN / DIN W W W . L M C - C O U P L I N G S . C O M
Materials and sizes
INCH 1/2” 3/4”-2” 2.1/2” 3”-4” 5”-6” 8”

Materials
ND
and sizes 13 20-50 65 75-100 125-150 200
Brass -
Bronze - -
Aluminium
Stainless steel
Polypropylene - - -
Available
- Not available
Material
Seal
Standard seal
The standard cam & groove seal consists of a standard square-section, available in:
VLXB... : NBR - Silicone free (standard for all materials, except for polypropylene)
VLXE... : EPDM (standard for material polypropylene)
VLXV... : FPM
VLXH... : CSM
Closed seal
VLXPSG closed cam & groove seals are designed for extreme chemical applications. These seals combine the best properties of two
different materials; the pressure set of the rubber Silicone core and the chemical resistance provided by the FEP encapsulation.
Encapsulation of the Silicone core ensures improved operational safety, when compared with an open envelope seal.
VLXPSG seals are produced without the use of animal derived ingredients, ADI free. This reduces the risk of BSE prion contamination.
VLXPSG closed cam & groove seals resist high temperature operation: from -60°C / -76°F up to 204°C / 399°F.
FEP envelope
VLXPSG...: Silicone core (standard)
FPM core (on request)
Open envelope seal

The open envelope seal consists of a U-section PTFE envelope and a square-section EPDM core. The construction method used for the
open envelope seal ensures excellent compression properties. The PTFE envelope allows the seal to withstand temperatures up to
200°C / 392°F.
PTFE envelope
VLXP...: EPDM core (standard)
FPM and Silicone core (on request)

a1-c&g 9/18/07 1:47 PM Pagina 5

A.1.
Closed envelope seal

The closed envelope seal removes all contact between chemicals and the seal core. The fully-closed PTFE envelope
completely encapsulates the FPM. The maximum temperature for this type is 200°C / 392°F.
PTFE envelope
VLXPG...: FPM core (standard)
MVQ core (on request)
Thread seal
Female threaded coupler and adaptor components complying with EN 14420-7 / DIN 2828 standards contain a thread
seal. Female threaded cam & groove couplings are sealed by screwing a male BSPT / BSP thread up to the thread seal.
Thread seals are available in: PTFE - PU
X2RP...: PTFE
X2RV...: PU
FED MIL / EN / DIN

Properties seals
REF. ASTM POLYMER TRADE NAME HARDNESS °C °F + PROPERTIES -
VLXB... NBR Acrylonitrile Butadiene Perbunan® 60 +/- 5 -30°C -22°F Oil based hydraulic Ozone,
Shore A 120°C 248°F fluid, fats, animal and sunlight
vegetable oils, flame weather
retardant, liquids, grease,
water and air
VLXE... EPDM Ethylene-propylene- Keltan® 70 +/- 5 -40°C -40°F Acids, steam, alcohol Oil,
Diene Rubber Shore A 145°C 293°F greases
VLXV... FPM Fluorocarbon Viton® 70 +/- 5 -30°C -22°F Mineral oils and greases, Steam
Shore A 200°C 392°F alifatic, aromatic, and also
special chlorinated hydro-
carbons, petrol, diesel fuels,
silicon oils and greases
VLXH... CSM Chlorosylfonated Hypalon® 70 +/- 5 -40°C -40°F Acids and oils, obsolescent Chlorine
polyethylene Shore A 140°C 284°F and ozone resistant
VLXPSG... FEP / Fluorinated ethylene propylene / Teflon® FEP / 60 +/- 5 -60°C -76°F Resistant to almost all kinds Hardness
MVQ Silicone Silicone Shore D 204°C 399°F of chemical products, steam,
oils... Excellent self-lubricating
and anti adhesive properties
VLXP... PTFE / Poly tetrafluorethylene / Teflon® / 85 +/-5 -25°C -13°F Alcohols, acids Hardness
EPDM Keltan® Shore D 100°C 212°F Oil, greases
VLXP...V PTFE / Poly tetrafluorethylene / Teflon® / 85 +/-5 -10°C 14°F Mineral oils and greases, Low temp.
FPM Fluorocarbon Viton® Shore D 200°C 392°F alifatics, aromatics
VLXPG... PTFE / Poly tetrafluorethylene / TFMTM PTFE / 74 +/- 5 -15°C 5°F Acids and oils, obsolescent Benzene,
FPM Fluorocarbon Viton® Shore D 200°C 392°F and ozone resistant toluene,
petrol
Perbunan® is a registered trademark of Bayer AG / Keltan® is a registered trademark of DSM / Viton® is a registered trademark of DuPont Performance Elastomer
Hypalon® is a registered trademark of DuPont Performance Elastomer / Teflon® is a registered trademark of DuPont Performance Elastomer
Silplus® is a registered trademark of General Electric Co / TFMTM is a registered trademark of Dyneon.

a1-c&g 9/18/07 1:47 PM Pagina 6
ASSEMBLY
Hose
Worm drive clamps
RK safety clamps to EN-14420-3 / DIN 2817
RKP safety clamps to EN-14420-3 / DIN 2817
Pipe
FLEXOLINE® safety clamps
Welding: butt welding and socket welding (see pg. A.1.27)
THREADS
Three different types of thread are generally used for cam & groove couplings:
BSP = British Standard Pipe thread

BSPT = British Standard Piper Taper thread
NPT = National Pipe Taper thread
In Europe, BSP and BSPT threads are more commonly used than NPT threads. NPT threads are typically American threads. Since many
American industrial machines and products are exported to European markets, couplings with NPT threads are a regular requirement. The
main difference between the three thread types referred to above is the seal method used. Although BSP threads are sealed using a seal
or o-ring, BSPT and NPT threads are sealed by their conical thread.
THREAD DESCRIPTION STANDARD TYPICAL CALL OUT SEALING METHOD PROPERTIES
BSP British standard pipe EN ISO 228-1 G1 Parallel thread 55° degree thread angle
Pressure tight joint is Trucation of rood and crest
obtained with a seal are round
or o-ring
BSPT British standard EN 10226-1 R1 Conical thread. 55° degree thread angle
pipe taper DIN 2999-1 Pressure tight joint is Trucation of rood and crest
achieved by the thread are round
NPT National pipe thread ANSI B 1.20.1 NPT 1 Conical thread 60° degree round angle
(American standard pipe thread) Pressure tight joint is Trucation of rood and crest
achieved by the thread are flat
Cam & groove threads
COUPLING TYPE STANDARD ON REQUEST
ADAPTOR
Female threaded A BSP EN ISO 228-1 NPT ANSI B 1.20.1

Male threaded F BSPT EN 10226-1 / DIN 2999-1 NPT ANSI B 1.20.1
COUPLER
Female threaded D BSP EN ISO 228-1 NPT ANSI B 1.20.1

Male threaded B BSPT EN 10226-1 / DIN 2999-1 NPT ANSI B 1.20.1

a1-c&g 9/18/07 1:47 PM Pagina 7
A.1.
TESTING

The following aspects of LMC’s cam & groove couplings are tested by the Research & Development department:
Adaptor and coupler dimensions

Material quality
Handle strength
Seal properties
Thread dimensions
Impact resistance
Adaptor and coupler dimensions

High-technology measuring equipment
High-technology measuring tools are used to measure the specific dimensions of cam &
groove couplings to ensure compliance with the dimensions required under the Federal Mil
A-A-59326A, European EN 14420-7 and the German DIN 2828 standards. Although ordinary
measuring systems are unable to give sufficiently precise dimensions for this purpose, our
high-technology measuring system is able to measure complex cam & groove coupling product
FED MIL / EN / DIN

positions and shapes.
Dimension gauges
The shape of the adaptor coupling enables the interchangeability of coupler parts. Specially
designed gauges are used in addition to measurement systems. The use of test gauges
minimises inspection times, ensures interchangeability and maintains seal properties when
using specially-designed seals, such as envelope seals.
Two gauges are used for each dimension; one small and the other larger. In the first stage of
testing, the small gauge is passed across the head of the adaptor section. If the gauge can not
pass, the adapter head falls within the permissible – (minus) tolerances.
If the larger gauge passes across the adaptor head with no interruption, the component is
compliant and its dimensions fall within the permissible + (plus) tolerances.
Material quality
An in-house spectroscope is used to identify the materials used in the cam & groove couplings.
The spectroscope analyses the precise quantity of all materials of the coupling.
We can therefore offer our customers a guarantee that the materials used comply fully with the
relevant standard.

a1-c&g 9/18/07 1:47 PM Pagina 8
Handle strength
LMC handles are designed to resist a wide range of applications in many industries. All standard handles are investment-cast and
triangular in section. The production method and triangular section guarantees excellent mechanical properties. The wear resistance
of this material was tested using a Rockwell hardness tester. LMC handles achieve better test results than sintered handles.
Sintered handles begin to fracture when subjected to a load of 14710 Newton, LMC handles do not even start to bend until subjec
ted to a load of 9807 Newton. Even when subjected to a load of 23536 NewtonLMC cam & groove handles still show no sign of fracture.
60000
(*) Fractured.
50000
(0, ) Bend, not fracture.
30000
Load N (Newton)
25000
Investment cast handle LMC
20000 Sintered handle
* *
10000 Investment cast handle others
0 0
0.0 2.5 5.0 7.5 10.0 12.5 15.0

Bending stroke (mm) Bend investment cast LMC handle Fractured sintered handle
Seal properties
After chemical structure, seal compression set has the next most significant effect on the seal of cam & groove couplings. A seal of
correct hardness will ensure that the cam & groove coupling is sealed properly and safely. Cam & groove seal hardness is tested using
a durometer.
Thread dimensions
All cam & groove threads are tested using thread gauges. Our production site has gauges for all dimensions and all standards.
Impact resistance
Impact resistance tests were carried out on 3” and 4” aluminium couplers and seven other brands in order to test the mechanical
strength of LMC cam & groove couplings. A 2.3 kg / 5 lbs weight was dropped from a height of 1.5 metres / 5 feet, and the impact on
the coupler body measured.
BRAND PRODUCTION METHOD

Impact E Gravity cast
Drop weight impact on F Gravity cast
bowl of coupler G Sand cast
A
H High pressure die cast
B Original ID: A I High pressure die cast
ID after impact: B J Squeeze die cast
K High pressure die cast
LMC High pressure die cast

a1-c&g 9/18/07 1:47 PM Pagina 9

A.1.

Size 3”
Type C C C C C C C B B C C D C
Brand E F G H H I J K K K K K LMC
Original ID A 92.14 91.72 91.98 92.21 92.01 92.53 91.98 92.24 92.42 92.74 92.58 92.15 93.54
1 91.75 89.43 89.86 91.06 91.67 90.98 91.16 91.43 91.12 91.48 91.59 91.31 93.17
2 91.38 88.65 90.57 90.54 90.08 89.57 91.00 90.43 90.68 91.20 90.75 92.57
3 90.73 90.54 90.27 89.06 88.66 90.26 90.30 90.28 91.11 90.38 92.57
4 90.56 90.25 90.09 90.12 89.28 90.68 90.30 92.35
5 90.16 90.05 89.83 90.65 89.78 92.19
6 90.11 90.00 90.47 89.72 91.92
7 89.55 89.49 91.89
8 89.35 89.44 91.87
Impact times B
9 89.37 89.33 91.79

10 89.33 91.77
11 89.22 91.76
12 89.14 91.55
13 91.68
14 91.58
15 91.58
16 91.65
17 91.61
18 91.19
FED MIL / EN / DIN

19 91.15
20 91.18
21 91.08
22 90.58
23 90.05
Measurements in mm
Adaptor unable to fit in coupler
Coupler cracked
Test result
The impact resistance test showed that the product quality of cam & groove couplings is variable. Nine couplers from different
manufacturers were also tested.
Five brands of adaptor were unable to fit the corresponding coupler following a single impact from a 2.3 kg / 5 lbs weight dropped
from a height of 1.5 metres / 5 feet. It took 18 such impacts before LMC-Couplings couplers were unable to fit their adaptors.
The average number of impacts required before fractures became aparent was 4.25. LMC-Couplings couplers resisted 23 impacts before
showing signs of fracture; a result far in excess of the average value.
94.50
0*
FUNCTIONAL
0* 0*
92.50 0* 0*
0* 0*
0* 0*
0* 0*
0*
0*
DX (MM)
1* 17 *
2* 1* 1* 1* 1*
1* 1*
1* 1* 18 *
2* 2*
3* 2*
90.50 2*
2* 2*
1*
1*
DISABLED
88.50
C(E) C(F) C(G) C(H) C(H) C(I) C(J) B(K) B(K) C(K) C(K) D(K) C(LMC)

a1-c&g 9/18/07 1:48 PM Pagina 10
COATINGS
Sometimes standard cam & groove coupling materials, like stainless steel, are not sufficiently resistant to extremely aggressive chemicals.
However, at LMC-Couplings, our couplings feature high-resistance coatings, such as:
ECTFE
PTFE
PFA
PVDF
ECTFE (up to 1000µm)

ECTFE (Ethylene chlorotrifluoroethylene) coatings are designed to resist highly-concentrated and aggressive chemicals. Couplings
with an ECTFE-coating show excellent electric isolating and fire properties and resist to temperatures up to 150°C / 302°F.
PFA (up to 200µm)

The key quality of a PFA (Perfluoroalkoxy) coating is the temperature resistance up to 260°C / 500°F. Their effective anti-ad-hesive
layer makes PFA coatings particularly well-suited to food and pharmaceutical industry applications.
PTFE (up to 40µm)

PTFE (Poly tetrafluoroethylene) coatings are only 40µ thick. PTFE-coated couplings can withstand temperatures up to 260°C / 500°F.
Like PFA-coated couplings, PTFE couplings have excellent anti-adhesive qualities and are suitable for food industry applications.
PVDF (up to 800µm)

Like ECTFE coatings, PVDF (Polyvinylidene fluoride) coatings can resist highly-concentrated and aggressive chemicals, but with the
added advantage of high temperature resistance up to 260°C / 500°F. These couplings are wear-proof and also suitable for food
industry applications.
PTFE liner
LMC-Couplings is able to provide his customers PTFE lined couplings. Our PTFE
facility has been specially built to meet the highest industrial requirements.
This room is separated from other production facilities to ensure a clean
and dust-free working environment. PTFE lined couplings are used in the phar-
maceutical, cosmetics and food industry for applications with a temperature
range of maximum 40°C / 104°F. Contact our sales department for
more information.

a1-c&g 9/18/07 1:48 PM Pagina 11

A.1.
ACCESSORIES

All LMC-Couplings, cam & groove couplings (stainless steel, brass, bronze, aluminium and
polypropylene)* as standard are supplied with stainless steel investment-cast triangular-section
handles. Stainless steel provides the best chemical resistance. Their triangular section and
1
investment-casting production method improves the mechanical strength of the handle.
Even greater security and safety is ensured by LMC’s cam & groove couplings with patented
safety handles. Simply push the nut on the handle downwards and the coupling connection is
sealed. The safety version of LMC’s cam & groove couplings can be made extra-secure by
using the safety pin, as on all standard LMC-Couplings cam & groove couplings. 2
Where dust caps (type DC) are used to terminate hose or pipe assemblies, LMC’s lockable han-
dles offer even higher safety levels. These patented L-shaped handles are physically locked, so
FED MIL / EN / DIN

that the dust cap can only be removed by unlocking the handles with a key. When using dust
caps safety handles are recommended for extra security.

3
* With exception of 8"
1 2 3
Handle types
TYPE HANDLE MATERIAL REFERENCE 1/2" 3/4" 1" 1.1/4" 1.1/2" 2" 2.1/2" 3" 4" 5" 6" 8"
Investment-cast Stainless steel VLHRPR

triangular handle standard
Investment-cast Brass VLHRPM - - - - - -
triangular handle
Safety locking handle Stainless steel VLHRPR S - - - - - - -
Cap L-handle Stainless steel VLHRPR L - - - -
available
- not available
8" aluminium with 4 handles

4" polypropylene with 3 handles
1/2” with 1 handle for all materials

a1-c&g 9/18/07 1:48 PM Pagina 12
CROSS REFERENCES
Cam & groove couplings
COUPLING TYPE DESCRIPTION EN REFERENCE COMMON USED REF.
A Adaptor, female threaded Federal Mil - 633-ABS
A Adaptor, female threaded EN 14420-7 / DIN 2828 AF 633-ABSF

with thread seal
B Coupler, female threaded EN 14420-7 / Federal Mil BF 633-BB
C Coupler, with serrated hose shank Federal Mil - 633-C
C Coupler, with smooth hose shank EN 14420-7 / DIN 2828 CC 633-CC
D Coupler, female threaded Federal Mil - 633-DBS
D Coupler, female threaded EN 14420-7 / DIN 2828 DF 633-DBSF

with thread seal
E Adaptor, with serrated hose shank Federal Mil - 633-E
E Adaptor, with smooth hose shank EN 14420-7 / DIN 2828 EC 633-EC
F Adaptor, male threaded Federal Mil / EN 14420-7 FF 633-FB
K Female dust cap Federal Mil / EN 14420-7 DC 634-B
P Male dust plug Federal Mil / EN 14420-7 DP 634-A
Cam & groove coupling VL A * 13 *

Material
A: Aluminium -: Federal Mil A-A-59326A
B: Bronze Size D: EN 14420-7 / DIN 2828
M: Brass S: With safety handles
P: Polypropylene SD: EN 14420-7 / DIN 2828 with safety handles
R: Stainless steel N: NPT thread
Cam & groove seals
Cam & groove coupling VL X * 13 Size
Seal
Material
B: NBR square seal
E: EPDM square seal
V: FPM square seal
H: CSM square seal
P: PTFE / EPDM open envelope seal
PG: PTFE / FPM closed envelope seal
PSG: FEP / Silicone closed square seal

a1-c&g 9/18/07 1:49 PM Pagina 13

A.1.
DIMENSIONS

FED MIL / EN / DIN
ND Inch A B C D E F G H J K L
13 1/2" 30 40 31 46 13 31 66 10 46 14 33
20 3/4" 115 50 33 49 19 55 85 14 49 21 34
25 1" 138 62 40 60 24 40 98 20 60 26 41
32 1.1/4” 178 81 46 68 31 46 104 26 70 35 48
40 1.1/2” 185 87 48 70 38 48 109 32 73 38 50
50 2" 195 90 54 79 48 54 124 43 79 46 57
65 2.1/2” 208 111 55 85 62 55 135 54 87 56 59
80 3" 250 143 57 90 75 57 159 66 92 73 62
100 4" 270 171 61 101 100 61 169 89 101 98 65
125 5" 300 - 61 101 122 61 188 118 105 128 65
150 6" 400 254 67 112 150 67 240 140 111 144 73
M N O P S T U V W X Y Z AA
13 24 37 14 10 62 28 24 52 37 14 4 26
13 32 40 19 14 76 25 32 57 40 19 10 26
13 43 48 23 19 92 36 43 69 49 23 10 23
13 50 55 28 25 98 41 58 77 55 28 10 40
13 56 36 36 31 102 44 56 78 56 36 10 42
13 68 62 46 43 117 49 68 87 62 46 10 48
13 85 86 56 56 129 51 85 98 68 56 10 49
13 102 88 73 64 153 51 102 108 70 73 10 51
13 126 78 98 89 168 55 126 118 78 98 12 53
13 - 83 118 118 188 56 - 103 63 118 12 58
16 - 82 150 138 230 60 - 108 68 150 12 58
Dimensions in mm and are given as illustration only.

a1-c&g 9/18/07 1:49 PM Pagina 14
a1-c&g 9/18/07 1:49 PM Pagina 15
W W W . L M C - C O U P L I N G S . C O M
A.1.

TYPE A: ADAPTOR FEMALE THREADED
ND Inch Thread Material Weight/pc Reference

EN ISO 228-1 Kg
15 1/2” G 1/2 Aluminium 0.02 VLAA013
20 3/4” G 3/4 Aluminium 0.04 VLAA019
25 1” G1 Aluminium 0.05 VLAA025
32 1.1/4” G 1.1/4 Aluminium 0.09 VLAA032
40 1.1/2” G 1.1/2 Aluminium 0.11 VLAA038
65 2.1/2” G 2.1/2 Aluminium 0.24 VLAA063
15 1/2” G 1/2 Stainless steel 0.07 VLAR013

20 3/4” G 3/4 Stainless steel 0.11 VLAR019
25 1” G1 Stainless steel 0.15 VLAR025
32 1.1/4” G 1.1/4 Stainless steel 0.24 VLAR032
FED MIL / EN / DIN

15 1/2” G 1/2 Brass 0.07 VLAM013

20 3/4” G 3/4 Brass 0.10 VLAM019
25 1” G1 Brass 0.15 VLAM025
32 1.1/4” G 1.1/4 Brass 0.20 VLAM032
40 1.1/2” G 1.1/2 Brass 0.29 VLAM038
50 2” G2 Brass 0.35 VLAM050
65 2.1/2” G 2.1/2 Brass 0.72 VLAM063
80 3” G3 Brass 0.73 VLAM075
100 4” G4 Brass 1.48 VLAM100
125 5” G5 Brass 1.79 VLAM125 A.1
150 6” G6 Brass 3.38 VLAM150
20 3/4” G 3/4 Bronze 0.12 VLAB019

25 1” G1 Bronze 0.16 VLAB025
32 1.1/4” G 1.1/4 Bronze 0.22 VLAB032
40 1.1/2” G 1.1/2 Bronze 0.29 VLAB038
50 2” G2 Bronze 0.47 VLAB050
65 2.1/2” G 2.1/2 Bronze 0.81 VLAB063
80 3” G3 Bronze 0.80 VLAB075
100 4” G4 Bronze 1.46 VLAB100
15 1/2” G 1/2 Polypropylene 0.02 VLAP013

20 3/4” G 3/4 Polypropylene 0.02 VLAP019
25 1” G1 Polypropylene 0.03 VLAP025
32 1.1/4” G 1.1/4 Polypropylene 0.05 VLAP032
40 1.1/2” G 1.1/2 Polypropylene 0.07 VLAP038
Coupling standard: Federal Mil A-A-59326A

Female thread: EN ISO 228-1, BSP
ANSI B 1.20.1, NPT on request
Stainless steel: AISI 316 / 1.4401
ND 200 stainless steel on request available

a1-c&g 9/18/07 1:50 PM Pagina 16
TYPE B: COUPLER MALE THREADED
ND Inch Thread Material Coupler Handles Weight/pc Reference

EN 10226-1 seal Kg
15 1/2” R 1/2 Aluminium NBR 1 0.07 VLBA013
20 3/4” R 3/4 Aluminium NBR 2 0.10 VLBA019
25 1” R1 Aluminium NBR 2 0.16 VLBA025
32 1.1/4” R 1.1/4 Aluminium NBR 2 0.27 VLBA032
15 1/2” R 1/2 Stainless steel NBR 1 0.12 VLBR013

20 3/4” R 3/4 Stainless steel NBR 2 0.20 VLBR019
25 1” R1 Stainless steel NBR 2 0.29 VLBR025
32 1.1/4” R 1.1/4 Stainless steel NBR 2 0.47 VLBR032
15 1/2” R 1/2 Brass NBR 1 0.17 VLBM013

20 3/4” R 3/4 Brass NBR 2 0.21 VLBM019
25 1” R1 Brass NBR 2 0.32 VLBM025
32 1.1/4” R 1.1/4 Brass NBR 2 0.45 VLBM032
40 1.1/2” R 1.1/2 Brass NBR 2 0.52 VLBM038
50 2” R2 Brass NBR 2 0.64 VLBM050
65 2.1/2” R 2.1/2 Brass NBR 2 0.94 VLBM063
80 3” R3 Brass NBR 2 1.38 VLBM075
100 4” R4 Brass NBR 2 1.94 VLBM100
125 5” R5 Brass NBR 2 3.98 VLBM125
150 6” R6 Brass NBR 2 3.65 VLBM150
20 3/4” R 3/4 Bronze NBR 2 0.22 VLBB019

25 1” R1 Bronze NBR 2 0.34 VLBB025
32 1.1/4” R 1.1/4 Bronze NBR 2 0.53 VLBB032
40 1.1/2” R 1.1/2 Bronze NBR 2 0.59 VLBB038
65 2.1/2” R 2.1/2 Bronze NBR 2 1.12 VLBB063
15 1/2” R 1/2 Polypropylene EPDM 2 0.07 VLBP013

20 3/4” R 3/4 Polypropylene EPDM 2 0.08 VLBP019
25 1” R1 Polypropylene EPDM 2 0.11 VLBP025
32 1.1/4” R 1.1/4 Polypropylene EPDM 2 0.21 VLBP032
40 1.1/2” R 1.1/2 Polypropylene EPDM 2 0.21 VLBP038
Coupling standard: Federal Mil A-A-59326A / EN 14420-7 / DIN 2828

Male thread: EN 10226-1 / DIN 2999-1, BSPT

a1-c&g 9/18/07 1:50 PM Pagina 17
A.1.

TYPE C: COUPLER WITH SERRATED HOSE SHANK
ND Inch For hose Collar Material Coupler Handles Weight/pc Reference

mm seal Kg
15 1/2” 13 x Aluminium NBR 1 0.07 VLCA013
20 3/4” 19 - Aluminium NBR 2 0.12 VLCA019
25 1” 25 - Aluminium NBR 2 0.17 VLCA025
32 1.1/4” 32 - Aluminium NBR 2 0.28 VLCA032
15 1/2” 13 - Stainless steel NBR 1 0.13 VLCR013

20 3/4” 19 x Stainless steel NBR 2 0.25 VLCR019
25 1” 25 x Stainless steel NBR 2 0.37 VLCR025
32 1.1/4” 32 x Stainless steel NBR 2 0.59 VLCR032
FED MIL / EN / DIN

15 1/2” 13 x Brass NBR 1 0.15 VLCM013

20 3/4” 19 - Brass NBR 2 0.23 VLCM019
25 1” 25 - Brass NBR 2 0.36 VLCM025
32 1.1/4” 32 - Brass NBR 2 0.49 VLCM032
40 1.1/2” 38 - Brass NBR 2 0.62 VLCM038
50 2” 50 - Brass NBR 2 0.77 VLCM050
65 2.1/2” 63 - Brass NBR 2 1.07 VLCM063
80 3” 75 - Brass NBR 2 1.58 VLCM075
100 4” 100 - Brass NBR 2 4.13 VLCM100
125 5” 125 - Brass NBR 2 3.32 VLCM125
150 6” 150 - Brass NBR 2 6.05 VLCM150
20 3/4” 19 - Bronze NBR 2 0.25 VLCB019

25 1” 25 - Bronze NBR 2 0.39 VLCB025
32 1.1/4” 32 - Bronze NBR 2 0.55 VLCB032
40 1.1/2” 38 - Bronze NBR 2 0.74 VLCB038
50 2” 50 - Bronze NBR 2 0.87 VLCB050
65 2.1/2” 63 - Bronze NBR 2 1.32 VLCB063
80 3” 75 - Bronze NBR 2 1.96 VLCB075
100 4” 100 - Bronze NBR 2 3.01 VLCB100
15 1/2” 13 - Polypropylene EPDM 2 0.07 VLCP013

20 3/4” 19 - Polypropylene EPDM 2 0.08 VLCP019
25 1” 25 - Polypropylene EPDM 2 0.12 VLCP025
32 1.1/4” 32 - Polypropylene EPDM 2 0.23 VLCP032
40 1.1/2” 38 - Polypropylene EPDM 2 0.23 VLCP038

Assembly: worm drive clamps, buckling, binding and band clamps
Hose shank and collar are subject to change without prior notice

a1-c&g 9/18/07 1:51 PM Pagina 18
TYPE D: COUPLER FEMALE THREADED
ND Inch Thread Material Coupler Handles Weight/pc Reference

EN ISO 228-1 seal Kg
15 1/2” G 1/2 Aluminium NBR 1 0.06 VLDA013
20 3/4” G 3/4 Aluminium NBR 2 0.12 VLDA019
25 1” G1 Aluminium NBR 2 0.16 VLDA025
32 1.1/4” G 1.1/4 Aluminium NBR 2 0.28 VLDA032
15 1/2” G 1/2 Stainless steel NBR 1 0.13 VLDR013

20 3/4” G 3/4 Stainless steel NBR 2 0.23 VLDR019
25 1” G1 Stainless steel NBR 2 0.31 VLDR025
32 1.1/4” G 1.1/4 Stainless steel NBR 2 0.49 VLDR032
15 1/2” G 1/2 Brass NBR 1 0.16 VLDM013

20 3/4” G 3/4 Brass NBR 2 0.22 VLDM019
25 1” G1 Brass NBR 2 0.32 VLDM025
32 1.1/4” G 1.1/4 Brass NBR 2 0.46 VLDM032
40 1.1/2” G 1.1/2 Brass NBR 2 0.54 VLDM038
50 2” G2 Brass NBR 2 0.67 VLDM050
65 2.1/2” G 2.1/2 Brass NBR 2 0.94 VLDM063
80 3” G3 Brass NBR 2 1.40 VLDM075
100 4” G4 Brass NBR 2 2.09 VLDM100
125 5” G5 Brass NBR 2 2.58 VLDM125
150 6” G6 Brass NBR 2 5.02 VLDM150
20 3/4” G 3/4 Bronze NBR 2 0.23 VLDB019

25 1” G1 Bronze NBR 2 0.35 VLDB025
32 1.1/4” G 1.1/4 Bronze NBR 2 0.50 VLDB032
40 1.1/2” G 1.1/2 Bronze NBR 2 0.66 VLDB038
65 2.1/2” G 2.1/2 Bronze NBR 2 0.95 VLDB063
15 1/2” G 1/2 Polypropylene EPDM 2 0.07 VLDP013

20 3/4” G 3/4 Polypropylene EPDM 2 0.08 VLDP019
25 1” G1 Polypropylene EPDM 2 0.13 VLDP025
32 1.1/4” G 1.1/4 Polypropylene EPDM 2 0.21 VLDP032
40 1.1/2” G 1.1/2 Polypropylene EPDM 2 0.23 VLDP038

Female thread: EN IS0 228-1, BSP

a1-c&g 9/18/07 1:51 PM Pagina 19
A.1.

TYPE E: ADAPTOR WITH SERRATED HOSE SHANK
ND Inch For hose Collar Material Weight/pc Reference

mm Kg
15 1/2” 13 - Aluminium 0.03 VLEA013
20 3/4” 19 x Aluminium 0.05 VLEA019
25 1” 25 x Aluminium 0.09 VLEA025
32 1.1/4” 32 x Aluminium 0.12 VLEA032
40 1.1/2” 38 x Aluminium 0.19 VLEA038
65 2.1/2” 63 x Aluminium 0.45 VLEA063
200 8” 200 - Aluminium 3.60 VLEA200
15 1/2” 13 x Stainless steel 0.07 VLER013

20 3/4” 19 x Stainless steel 0.14 VLER019
25 1” 25 x Stainless steel 0.25 VLER025
32 1.1/4” 32 x Stainless steel 0.37 VLER032
FED MIL / EN / DIN

15 1/2” 13 - Brass 0.11 VLEM013

20 3/4” 19 x Brass 0.16 VLEM019
25 1” 25 x Brass 0.24 VLEM025
32 1.1/4” 32 x Brass 0.33 VLEM032
40 1.1/2” 38 x Brass 0.44 VLEM038
50 2” 50 x Brass 0.73 VLEM050
65 2.1/2” 63 x Brass 0.96 VLEM063
80 3” 75 x Brass 1.25 VLEM075
100 4” 100 x Brass 1.91 VLEM100
125 5” 125 x Brass 4.54 VLEM125
150 6” 150 x Brass 5.07 VLEM150
20 3/4” 19 x Bronze 0.18 VLEB019

25 1” 25 x Bronze 0.29 VLEB025
32 1.1/4” 32 x Bronze 0.40 VLEB032
40 1.1/2” 38 x Bronze 0.56 VLEB038
50 2” 50 x Bronze 0.80 VLEB050
65 2.1/2” 63 x Bronze 1.12 VLEB063
80 3” 75 x Bronze 1.67 VLEB075
100 4” 100 x Bronze 1.96 VLEB100
15 1/2” 13 x Polypropylene 0.01 VLEP013

20 3/4” 19 x Polypropylene 0.03 VLEP019
25 1” 25 x Polypropylene 0.04 VLEP025
32 1.1/4” 32 x Polypropylene 0.07 VLEP032
40 1.1/2” 38 x Polypropylene 0.09 VLEP038

Hose shank and collar are subject to change without prior notice

a1-c&g 9/18/07 1:51 PM Pagina 20
TYPE F: ADAPTOR MALE THREADED

EN 10226-1 Kg
15 1/2” R 1/2 Aluminium 0.03 VLFA013
20 3/4” R 3/4 Aluminium 0.07 VLFA019
25 1” R1 Aluminium 0.09 VLFA025
32 1.1/4” R 1.1/4 Aluminium 0.12 VLFA032
40 1.1/2” R 1.1/2 Aluminium 0.18 VLFA038
65 2.1/2” R 2.1/2 Aluminium 0.36 VLFA063
15 1/2” R 1/2 Stainless steel 0.09 VLFR013

20 3/4” R 3/4 Stainless steel 0.16 VLFR019
25 1” R1 Stainless steel 0.26 VLFR025
32 1.1/4” R 1.1/4 Stainless steel 0.40 VLFR032
15 1/2” R 1/2 Brass 0.09 VLFM013

20 3/4” R 3/4 Brass 0.15 VLFM019
25 1” R1 Brass 0.23 VLFM025
32 1.1/4” R 1.1/4 Brass 0.30 VLFM032
40 1.1/2” R 1.1/2 Brass 0.35 VLFM038
50 2” R2 Brass 0.51 VLFM050
65 2.1/2” R 2.1/2 Brass 0.80 VLFM063
80 3” R3 Brass 0.94 VLFM075
100 4” R4 Brass 1.71 VLFM100
125 5” R5 Brass 3.32 VLFM125
150 6” R6 Brass 3.78 VLFM150
20 3/4” R 3/4 Bronze 0.16 VLFB019

25 1” R1 Bronze 0.24 VLFB025
32 1.1/4” R 1.1/4 Bronze 0.31 VLFB032
40 1.1/2” R 1.1/2 Bronze 0.42 VLFB038
50 2” R2 Bronze 0.66 VLFB050
65 2.1/2” R 2.1/2 Bronze 0.95 VLFB063
80 3” R3 Bronze 1.25 VLFB075
100 4” R4 Bronze 2.32 VLFB100
15 1/2” R 1/2 Polypropylene 0.02 VLFP013

20 3/4” R 3/4 Polypropylene 0.03 VLFP019
25 1” R1 Polypropylene 0.05 VLFP025
32 1.1/4” R 1.1/4 Polypropylene 0.08 VLFP032
40 1.1/2” R 1.1/2 Polypropylene 0.10 VLFP038


a1-c&g 9/18/07 1:52 PM Pagina 21
A.1.

TYPE DC: FEMALE DUST CAP
ND Inch Material Coupler Handles Weight/pc Reference

seal Kg
15 1/2” Aluminium NBR 1 0.05 VLKA013
20 3/4” Aluminium NBR 2 0.10 VLKA019
25 1” Aluminium NBR 2 0.14 VLKA025
32 1.1/4” Aluminium NBR 2 0.24 VLKA032
15 1/2” Stainless steel NBR 1 0.13 VLKR013

20 3/4” Stainless steel NBR 2 0.18 VLKR019
25 1” Stainless steel NBR 2 0.25 VLKR025
32 1.1/4” Stainless steel NBR 2 0.43 VLKR032
FED MIL / EN / DIN

15 1/2” Brass NBR 1 0.12 VLKM013

20 3/4” Brass NBR 2 0.13 VLKM019
25 1” Brass NBR 2 0.27 VLKM025
32 1.1/4” Brass NBR 2 0.41 VLKM032
40 1.1/2” Brass NBR 2 0.48 VLKM038
65 2.1/2” Brass NBR 2 0.77 VLKM063
100 4” Brass NBR 2 1.87 VLKM100
125 5” Brass NBR 2 2.10 VLKM125
150 6” Brass NBR 2 3.72 VLKM150
20 3/4” Bronze NBR 2 0.18 VLKB019

25 1” Bronze NBR 2 0.31 VLKB025
32 1.1/4” Bronze NBR 2 0.49 VLKB032
40 1.1/2” Bronze NBR 2 0.56 VLKB038
65 2.1/2” Bronze NBR 2 0.92 VLKB063
15 1/2” Polypropylene EPDM 2 0.07 VLKP013

20 3/4” Polypropylene EPDM 2 0.07 VLKP019
25 1” Polypropylene EPDM 2 0.10 VLKP025
32 1.1/4” Polypropylene EPDM 2 0.20 VLKP032
40 1.1/2” Polypropylene EPDM 2 0.22 VLKP038

Standard hole for chain

a1-c&g 9/18/07 1:52 PM Pagina 22
TYPE DP: MALE DUST PLUG
ND Inch Material Weight/pc Reference

Kg
15 1/2” Aluminium 0.02 VLPA013
20 3/4” Aluminium 0.03 VLPA019
25 1” Aluminium 0.05 VLPA025
32 1.1/4” Aluminium 0.07 VLPA032
15 1/2” Stainless steel 0.06 VLPR013

20 3/4” Stainless steel 0.08 VLPR019
25 1” Stainless steel 0.13 VLPR025
32 1.1/4” Stainless steel 0.25 VLPR032
15 1/2” Brass 0.07 VLPM013

20 3/4” Brass 0.09 VLPM019
25 1” Brass 0.13 VLPM025
32 1.1/4” Brass 0.20 VLPM032
40 1.1/2” Brass 0.24 VLPM038
50 2” Brass 0.40 VLPM050
65 2.1/2” Brass 0.59 VLPM063
80 3” Brass 0.72 VLPM075
100 4” Brass 1.03 VLPM100
125 5” Brass 1.60 VLPM125
150 6” Brass 1.80 VLPM150
20 3/4” Bronze 0.10 VLPB019

25 1” Bronze 0.15 VLPB025
32 1.1/4” Bronze 0.24 VLPB032
40 1.1/2” Bronze 0.32 VLPB038
65 2.1/2” Bronze 0.60 VLPB063
100 4” Bronze 1.42 VLPB100
15 1/2” Polypropylene 0.01 VLPP013

20 3/4” Polypropylene 0.02 VLPP019
25 1” Polypropylene 0.02 VLPP025
32 1.1/4” Polypropylene 0.04 VLPP032
40 1.1/2” Polypropylene 0.05 VLPP038


a1-c&g 9/18/07 1:53 PM Pagina 23
A.1.
CAM & GROOVE COUPLINGS EN 14420-7 / DIN 2828

TYPE A: ADAPTOR FEMALE THREADED WITH THREAD SEAL
ND Inch Thread Thread Material Weight/pc Reference

EN ISO 228-1 seal Kg
20 3/4” G 3/4 PTFE Stainless steel 0.11 VLAR019D
25 1” G1 PTFE Stainless steel 0.18 VLAR025D
32 1.1/4” G 1.1/4 PTFE Stainless steel 0.31 VLAR032D
50 2” G2 PU Brass 0.71 VLAM050D

65 2.1/2” G 2.1/2 PU Brass 0.80 VLAM063D
Coupling standard: EN 14420-7 / DIN 2828
FED MIL / EN / DIN

Thread seal: PTFE for stainless steel coupling
PU for brass coupling Thread seal
TYPE E: ADAPTOR WITH SMOOTH HOSE SHANK
ND Inch For hose Material Weight/pc Reference

mm Kg
20 3/4” 19 Stainless steel 0.13 VLER019D
25 1” 25 Stainless steel 0.20 VLER025D
32 1.1/4” 32 Stainless steel 0.33 VLER032D
20 3/4” 19 Brass 0.14 VLEM019D

25 1” 25 Brass 0.21 VLEM025D
32 1.1/4” 32 Brass 0.35 VLEM032D
40 1.1/2” 38 Brass 0.45 VLEM038D
50 2” 50 Brass 0.66 VLEM050D
65 2.1/2” 63 Brass 0.98 VLEM063D
80 3” 75 Brass 1.26 VLEM075D
100 4” 100 Brass 2.69 VLEM100D

Shank standard: EN 14420-2 / DIN 2828
Assembly: RK safety clamps EN 14420-3 / DIN 2817, FLEXOLINE® safety clamps (see chapter D)
Stainless steel: AISI 316 / 1.4401 Smooth hose shank
and collar

a1-c&g 9/18/07 1:53 PM Pagina 24
CAM & GROOVE COUPLINGS EN 14420-7 / DIN 2828
TYPE D: COUPLER FEMALE THREADED WITH THREAD SEAL
ND Inch Thread Thread Material Coupler Weight/pc Reference

EN ISO 228-1 seal seal Kg
20 3/4” G 3/4 PTFE Stainless steel NBR 0.18 VLDR019D
25 1” G1 PTFE Stainless steel NBR 0.29 VLDR025D
32 1.1/4” G 1.1/4 PTFE Stainless steel NBR 0.58 VLDR032D

Thread seal: PTFE - white for stainless steel coupling
Stainless steel: AISI 316 / 1.4401 Thread seal
Brass available upon request
TYPE C: COUPLER WITH SMOOTH HOSE SHANK
ND Inch For hose Coupler Material Weight/pc Reference

mm seal Kg
20 3/4” 19 NBR Stainless steel 0.24 VLCR019D
25 1” 25 NBR Stainless steel 0.35 VLCR025D
32 1.1/4” 32 NBR Stainless steel 0.59 VLCR032D
20 3/4” 19 NBR Brass 0.25 VLCM019D

25 1” 25 NBR Brass 0.38 VLCM025D
32 1.1/4” 32 NBR Brass 0.63 VLCM032D
40 1.1/2” 38 NBR Brass 0.69 VLCM038D
65 2.1/2” 63 NBR Brass 1.18 VLCM063D
100 4” 100 NBR Brass 2.71 VLCM100D

Stainless steel: AISI 316 / 1.4401 Smooth hose shank
and collar

a1-c&g 9/18/07 1:53 PM Pagina 25
A.1.
CAM & GROOVE SAFETY COUPLINGS

TYPE D: COUPLER FEMALE THREADED WITH SAFETY HANDLES

EN ISO 228-1 Kg
25 1” G 1” Stainless steel 0.47 VLDR025S
40 1.1/2” G 1.1/2” Stainless steel 0.82 VLDR038S

Female thread: EN IS0 228-1, BSP
Version: monoblock safety body
TYPE B: COUPLER MALE THREADED WITH SAFETY HANDLES
FED MIL / EN / DIN

EN 10226-1 Kg
25 1” R1 Stainless steel 0.45 VLBR025S
40 1.1/2” R 1.1/2 Stainless steel 0.75 VLBR038S

TYPE C: COUPLER WITH SERRATED HOSE SHANK AND SAFETY HANDLES
ND Inch For hose Collar Material Weight/pc Reference

mm Kg
25 1” 25 - Stainless steel 0.51 VLCR025S
40 1.1/2” 38 x Stainless steel 0.90 VLCR038S
50 2” 50 x Stainless steel 1.33 VLCR050S

Collar is subjet to change without prior notice

a1-c&g 9/18/07 1:54 PM Pagina 26
CAM & GROOVE SAFETY COUPLINGS
TYPE C: COUPLER WITH SMOOTH HOSE SHANK AND SAFETY HANDLES
ND Inch For hose Material Weight/pc Reference

mm Kg
40 1.1/2” 38 Stainless steel 0.79 VLCR038SD
50 2” 50 Stainless steel 1.06 VLCR050SD

TYPE DC: FEMALE DUST CAP WITH SAFETY HANDLES

Kg
25 1” Stainless steel 0.43 VLKR025S
40 1.1/2” Stainless steel 0.70 VLKR038S

Standard chain access
SAFETY REBUILDING SET

Kg
25 1” Stainless steel 0.10 VLHRPR2S
32 - 65 1.1/2” - 2” Stainless steel 0.13 VLHRPR3S
80 - 125 3”-5” Stainless steel 0.17 VLHRPR4S
Safety rebuilding set: Safety handle stainless steel AISI 304 - 1.4301
Pull ring stainless steel AISI 304 - 1.4301
Safety pin stainless steel AISI 304 - 1.4301
Safety hook stainless steel AISI 304 - 1.4301
VLHRPR2S VLHRPR4S SAFETY
VLHRPR3S HOOK

a1-c&g 9/18/07 1:54 PM Pagina 27
A.1.
CAM & GROOVE WELDING COUPLINGS
Butt weld vs socket weld

Cam & groove couplings can be welded on hoses, pipes an other welding couplings by using:
cam & groove couplings with butt weld connection

cam & groove couplings with socket weld connection
Butt welding
Welding ends with a butt weld connection are used for welding the majority of cam & groove
Butt weld connection
couplings. A butt weld connection consists of a 30° chamfered welding end.
Socket welding
In socket welding, the pipe or hose slides partially inside the coupling. Both components are then
welded together at the point of insertion. Stainless steel socket welding couplings provide a tight
and integral line system that remains unaffected by shock, vibration or termal distortion.
Socket weld connection

Welding dimensions
The welding dimensions for cam & groove couplings are based on inch sizes.
FED MIL / EN / DIN

ND INCH A mm B mm
15 1/2" 21.34 2.0

20 3/4" 26.67 2.3
25 1" 33.40 2.6
A
32 1.1/4” 42.16 2.6
40 1.1/2” 48.26 2.6 B
50 2" 60.33 2.9

65 2.1/2” 76.03 2.9
80 3" 88.90 3.2
100 4" 114.30 3.6
A
125 5" 139.70 4.0
150 6" 168.28 4.5
TYPE AWB: ADAPTOR WITH BUTT WELD CONNECTION

Kg
15 1/2” Stainless steel 0.11 VLAWBR013
20 3/4” Stainless steel 0.16 VLAWBR019
25 1” Stainless steel 0.26 VLAWBR025
32 1.1/4” Stainless steel 0.41 VLAWBR032
30°
Welding end: butt weld end to inch size


a1-c&g 9/18/07 1:55 PM Pagina 28
CAM & GROOVE WELDING COUPLINGS
TYPE DWB: COUPLER WITH BUTT WELD CONNECTION

Kg
15 1/2” Stainless steel 0.12 VLDWBR013
20 3/4” Stainless steel 0.20 VLDWBR019
25 1” Stainless steel 0.29 VLDWBR025
32 1.1/4” Stainless steel 0.50 VLDWBR032
150 6” Stainless steel 3.67 VLDWBR150 30°
Welding end: butt weld end to inch size

TYPE AWS: ADAPTOR WITH SOCKET WELD CONNECTION

Kg
15 1/2” Stainless steel 0.07 VLAWSR013
20 3/4” Stainless steel 0.11 VLAWSR019
25 1” Stainless steel 0.15 VLAWSR025
32 1.1/4” Stainless steel 0.24 VLAWSR032
Welding end: socket weld end to inch size

TYPE DWS: COUPLER WITH SOCKET WELD CONNECTION

Kg
15 1/2” Stainless steel 0.13 VLDWSR013
20 3/4” Stainless steel 0.23 VLDWSR019
25 1” Stainless steel 0.36 VLDWSR025
32 1.1/4” Stainless steel 0.48 VLDWSR032
Welding end: socket weld end to inch size


a1-c&g 9/18/07 1:55 PM Pagina 29
A.1.
CAM & GROOVE FLANGE COUPLINGS

TYPE AF: ADAPTOR WITH FIXED FLANGE IN COMPLIANCE WITH EN/DIN
ND Inch Material Welding neck flange Total Weight/pc Reference

length* Kg
15 1/2” Stainless steel DIN 2633 - PN 10/16 92.0 0.82 VLAFDR013
20 3/4” Stainless steel DIN 2633 - PN 10/16 95.0 1.22 VLAFDR019
25 1” Stainless steel DIN 2633 - PN 10/16 105.0 1.35 VLAFDR025
32 1.1/4” Stainless steel DIN 2633 - PN 10/16 114.0 2.05 VLAFDR032

Flange standard: EN 1092-1/ 11 B1; DIN 2633 form C, PN 10/16
FED MIL / EN / DIN

*Total length flange coupling in mm and is subject to change without prior notice
TYPE AF: ADAPTOR WITH FIXED FLANGE IN COMPLIANCE WITH ASTM

length* Kg
15 1/2” Stainless steel ASTM - ASA 150 lbs 105.0 0.81 VLAFA1R013
20 3/4” Stainless steel ASTM - ASA 150 lbs 113.0 0.96 VLAFA1R019
25 1” Stainless steel ASTM - ASA 150 lbs 123.0 1.36 VLAFA1R025
32 1.1/4” Stainless steel ASTM - ASA 150 lbs 131.0 1.91 VLAFA1R032

Flange standard: ASTM A 182 and ASME B16.5, RF, ASA 150 lbs

a1-c&g 9/18/07 1:56 PM Pagina 30
CAM & GROOVE FLANGE COUPLINGS
TYPE DF: COUPLER WITH FIXED FLANGE IN COMPLIANCE WITH EN/DIN

length* Kg
15 1/2” Stainless steel DIN 2633 PN 10/16 81.0 0.92 VLDFDR013
20 3/4” Stainless steel DIN 2633 PN 10/16 90.0 1.16 VLDFDR019
25 1” Stainless steel DIN 2633 PN 10/16 96.0 1.39 VLDFDR025
32 1.1/4” Stainless steel DIN 2633 PN 10/16 111.0 2.34 VLDFDR032

Flange standard: EN 1092-1/ 11 B1; DIN 2633 form C, PN 10/16
TYPE DF: COUPLER WITH FIXED FLANGE IN COMPLIANCE WITH ASTM

length* Kg
15 1/2” Stainless steel ASTM - ASA 150 lbs 94.0 0.62 VLDFA1R013
20 3/4” Stainless steel ASTM - ASA 150 lbs 108.0 0.90 VLDFA1R019
25 1” Stainless steel ASTM - ASA 150 lbs 114.0 1.09 VLDFA1R025
32 1.1/4” Stainless steel ASTM - ASA 150 lbs 128.0 1.70 VLDFA1R032

Flange standard: ASTM A 182 and ASME B16.5, RF, ASA 150 lbs

a1-c&g 9/18/07 1:56 PM Pagina 31
A.1.
CAM & GROOVE SPOOL COUPLINGS

TYPE AA: SPOOL ADAPTOR

Kg
40 1.1/2” Aluminium 0.20 VLAAA038
50 2” Aluminium 0.30 VLAAA050
50-80 2” - 3” Aluminium 0.48 VLAAA050075
65 2.1/2” Aluminium 0.49 VLAAA063
80 3” - 4” Aluminium 0.81 VLAAA075100
20 3/4” Stainless steel 0.22 VLAAR019

25 1” Stainless steel 0.36 VLAAR025
40 1.1/2” Stainless steel 0.82 VLAAR038
40-50 1.1/2” - 2” Stainless steel 0.96 VLAAR038050
50-80 2” - 3” Stainless steel 1.46 VLAAR050075
80-100 3” - 4” Stainless steel 2.55 VLAAR075100
FED MIL / EN / DIN

40 1.1/2” Brass 0.59 VLAAM038
50 2” Brass 0.90 VLAAM050
65 2.1/2” Brass 1.49 VLAAM063
80 3” Brass 1.45 VLAAM075
100 4” Brass 2.33 VLAAM100

Version: monoblock
TYPE DD: SPOOL COUPLER
ND Inch Material Coupler Weight Reference

seal kg
40 1.1/2” Stainless steel NBR 0.96 VLDDR038
50 2” Stainless steel NBR 1.29 VLDDR050

Version: monoblock

a1-c&g 9/18/07 1:56 PM Pagina 32
CAM & GROOVE SPOOL COUPLINGS
TYPE DA: SPOOL COUPLER - ADAPTOR

Coupler-Adaptor Coupler-Adaptor Kg
50-80 2” - 3” Aluminium 0.75 VLDAA050075
80-50 3” - 2” Aluminium 1.14 VLDAA075050
80-100 3” - 4” Aluminium 1.30 VLDAA075100
100-50 4” - 2” Aluminium 1.26 VLDAA100050
100-80 4” - 3” Aluminium 1.51 VLDAA100075
100-150 4” - 6” Aluminium 1.92 VLDAA100150
50-80 2” - 3” Stainless steel 1.75 VLDAR050075

50-80 2” - 3” Brass 1.96 VLDAM050075

80-50 3” - 2” Brass 2.80 VLDAM075050
100-50 4” - 2” Brass 3.22 VLDAM100050
100-80 4” - 3” Brass 4.31 VLDAM100075
150-100 6” - 4” Brass 8.16 VLDAM150100

Version: monoblock

a1-c&g 9/18/07 1:57 PM Pagina 33
A.1.
CAM & GROOVE REDUCING COUPLINGS

TYPE A: REDUCING ADAPTOR FEMALE THREADED
ND - Inch Thread EN ISO 228-1 Material Weight/pc Reference

Adaptor
thre Kg
20 - 3/4" G 1/2 Polypropylene 0.03 VLAP019013
40 - 1.1/2" G 1.1/4 Polypropylene 0.23 VLAP038032

TYPE B: REDUCING COUPLER MALE THREADED
ND - Inch Thread EN 10226-1 Material Weight/pc Reference

Coupler Kg
FED MIL / EN / DIN

40 - 1.1/2” R1 Aluminium 0.31 VLBA038025
50 - 2” R 1.1/2 Aluminium 0.37 VLBA050038
80 - 3” R2 Aluminium 0.86 VLBA075050
100 - 4” R3 Aluminium 1.20 VLBA100075
20 - 3/4” R 1/2 Polypropylene 0.07 VLBP019013

40 - 1.1/2” R 1.1/4 Polypropylene 0.23 VLBP038032

Male thread: EN 10226-1, BSPT
TYPE C: REDUCING COUPLER WITH SERRATED HOSE SHANK
ND - Inch For hose Material Weight/pc Reference

Coupler mm Kg
50 - 2” 38 Aluminium 0.44 VLCA050038
80 - 3” 50 Aluminium 0.86 VLCA075050
80 - 3” 100 Aluminium 1.10 VLCA075100
100 - 4” 75 Aluminium 1.20 VLCA100075
20 - 3/4” 13 Polypropylene 0.07 VLCP019013

40 - 1.1/2” 32 Polypropylene 0.24 VLCP038032


a1-c&g 9/18/07 1:57 PM Pagina 34
CAM & GROOVE REDUCING COUPLINGS
TYPE D: REDUCING COUPLER FEMALE THREADED
ND - Inch Thread EN ISO 228-1 Material Weight/pc Reference

Coupler Kg
40 - 1.1/2” G1 Aluminium 0.32 VLDA038025
50 - 2” G 1.1/2 Aluminium 0.39 VLDA050038
80 - 3” G2 Aluminium 0.72 VLDA075050
100 - 4” G3 Aluminium 1.11 VLDA100075

TYPE E: REDUCING ADAPTOR WITH SERRATED HOSE SHANK
ND - Inch For hose Material Weight/pc Reference

Adaptor mm Kg
20 - 3/4” 13 Polypropylene 0.03 VLEP019013
40 - 1.1/2” 32 Polypropylene 0.08 VLEP038032

TYPE F: REDUCING ADAPTOR MALE THREADED
ND - Inch Thread EN 10226-1 Material Weight/pc Reference

Adaptor Kg
20 - 3/4” R 1/2 Polypropylene 0.03 VLFP019013
40 - 1.1/2” R 1.1/4 Polypropylene 0.09 VLFP038032

Male thread: EN 10226-1, BSPT

a1-c&g 9/18/07 1:57 PM Pagina 35
A.1.
CAM & GROOVE SEALS

SQUARE SEAL - NBR
ND Inch OD Ø +/- 0.3 mm ID Ø +/- 0.2 mm Height +/- 0.2 mm Weight/pc Reference
Kg
15 1/2” 26.5 17.5 4.0 0.002 VLXB013
20 3/4” 35.0 22.0 5.5 0.005 VLXB019
25 1” 40.0 27.0 6.4 0.007 VLXB025
32 1.1/4” 50.0 35.0 6.4 0.009 VLXB032
40 1.1/2” 56.0 41.0 6.4 0.010 VLXB038
50 2” 67.0 51.0 6.4 0.010 VLXB050
65 2.1/2” 80.0 60.0 6.4 0.020 VLXB063
80 3” 95.0 76.0 6.4 0.020 VLXB075
100 4” 124.0 102.0 6.4 0.030 VLXB100
125 5” 150.5 124.0 6.4 0.050 VLXB125
150 6” 180.0 153.0 6.4 0.060 VLXB150
200 8” 232.5 203.5 7.9 0.070 VLXB200
Material: NBR - Silicone free

Colour: Black
FED MIL / EN / DIN

Dimensions in compliance with EN 14420-7, with exception of ND 15, ND 125, ND 150 and ND 200
See chapter E for more information regarding chemical resistance
SQUARE SEAL - EPDM
Kg
15 1/2” 26.5 17.5 4.0 0.002 VLXE013
20 3/4” 35.0 22.0 5.5 0.005 VLXE019
25 1” 40.0 27.0 6.4 0.007 VLXE025
32 1.1/4” 50.0 35.0 6.4 0.009 VLXE032
40 1.1/2” 56.0 41.0 6.4 0.010 VLXE038
50 2” 67.0 51.0 6.4 0.010 VLXE050
65 2.1/2” 80.0 60.0 6.4 0.020 VLXE063
80 3” 95.0 76.0 6.4 0.020 VLXE075
100 4” 124.0 102.0 6.4 0.030 VLXE100
125 5” 150.5 124.0 6.4 0.050 VLXE125
150 6” 180.0 153.0 6.4 0.060 VLXE150
Material: EPDM
Colour: Black yellow marked

a1-c&g 9/18/07 1:58 PM Pagina 36
CAM & GROOVE SEALS
SQUARE SEAL - FPM
Kg
15 1/2” 26.5 17.5 4.0 0.002 VLXV013
20 3/4” 35.0 22.0 5.5 0.005 VLXV019
25 1” 40.0 27.0 6.4 0.007 VLXV025
32 1.1/4” 50.0 35.0 6.4 0.009 VLXV032
40 1.1/2” 56.0 41.0 6.4 0.010 VLXV038
50 2” 67.0 51.0 6.4 0.010 VLXV050
65 2.1/2” 80.0 60.0 6.4 0.020 VLXV063
80 3” 95.0 76.0 6.4 0.020 VLXV075
100 4” 124.0 102.0 6.4 0.030 VLXV100
125 5” 150.5 124.0 6.4 0.050 VLXV125
150 6” 180.0 153.0 6.4 0.060 VLXV150
Material: FPM
Colour: Green
SQUARE SEAL - CSM
Kg
15 1/2” 26.5 17.5 4.0 0.002 VLXH013
20 3/4” 35.0 22.0 5.5 0.005 VLXH019
25 1” 40.0 27.0 6.4 0.007 VLXH025
32 1.1/4” 50.0 35.0 6.4 0.009 VLXH032
40 1.1/2” 56.0 41.0 6.4 0.010 VLXH038
50 2” 67.0 51.0 6.4 0.010 VLXH050
65 2.1/2” 80.0 60.0 6.4 0.020 VLXH063
80 3” 95.0 76.0 6.4 0.020 VLXH075
100 4” 124.0 102.0 6.4 0.030 VLXH100
125 5” 150.5 124.0 6.4 0.050 VLXH125
150 6” 180.0 153.0 6.4 0.060 VLXH150
Material: CSM
Colour: Black green marked

a1-c&g 9/18/07 1:58 PM Pagina 37
A.1.
CAM & GROOVE SEALS

CLOSED SEAL - FEP / SILICONE
Kg
15 1/2” 26.6 17.5 4.0 0.002 VLXPSG013
20 3/4” 35.0 22.2 5.5 0.004 VLXPSG019
25 1” 39.7 27.0 6.5 0.006 VLXPSG025
32 1.1/4” 49.2 34.5 6.5 0.010 VLXPSG032
40 1.1/2” 55.5 41.3 6.5 0.012 VLXPSG038
50 2” 66.7 50.8 6.5 0.014 VLXPSG050
65 2.1/2” 79.4 60.3 6.5 0.018 VLXPSG063
80 3” 95.5 76.2 6.5 0.022 VLXPSG075
Material: FEP encapsulation - Silicone core

Colour: Translucent outside / red inside
Seal and seal dimensions not specified by EN 14420-7 / FED MIL A-A59326A
FDA conformity certificate on request available
FED MIL / EN / DIN

OPEN ENVELOPE SEAL - PTFE / EPDM
Kg
15 1/2” 26.2 17.5 4.0 0.002 VLXP013
20 3/4” 35.3 21.2 5.5 0.004 VLXP019
25 1” 39.0 23.0 6.4 0.006 VLXP025
32 1.1/4” 49.5 32.4 6.4 0.009 VLXP032
40 1.1/2” 55.2 35.2 6.4 0.012 VLXP038
50 2” 66.0 47.0 6.4 0.014 VLXP050
63 2.1/2” 79.0 58.5 6.4 0.020 VLXP063
80 3” 94.5 76.3 6.4 0.022 VLXP075
100 4” 124.0 102.0 6.4 0.032 VLXP100
Material: PTFE envelope / EPDM core

Colour: White outside / black inside

a1-c&g 9/18/07 1:58 PM Pagina 38
CAM & GROOVE SEALS
OPEN ENVELOPE SEAL - PTFE / FPM
Kg
15 1/2” 26.2 17.5 4.0 0.002 VLXP013V
20 3/4” 35.3 21.2 5.5 0.004 VLXP019V
25 1” 39.0 23.0 6.4 0.006 VLXP025V
32 1.1/4” 49.5 32.4 6.4 0.009 VLXP032V
40 1.1/2” 55.2 35.2 6.4 0.012 VLXP038V
50 2” 66.0 47.0 6.4 0.014 VLXP050V
65 2.1/2” 79.0 58.5 6.4 0.020 VLXP063V
80 3” 94.5 76.3 6.4 0.022 VLXP075V
100 4” 124.0 102.0 6.4 0.032 VLXP100V
Material: PTFE envelope / FPM core

Colour: White outside / black grey marked inside
CLOSED ENVELOPE SEAL - PTFE / FPM
Kg
15 1/2” 26.5 13.5 4.5 0.002 VLXPG013
20 3/4” 35.0 18.0 5.7 0.004 VLXPG020
25 1” 41.8 23.5 6.5 0.006 VLXPG025
32 1.1/4” 48.0 30.0 6.5 0.009 VLXPG032
40 1.1/2” 56.0 35.5 6.5 0.010 VLXPG038
50 2” 67.0 46.5 6.5 0.012 VLXPG050
65 2.1/2” 81.5 60.0 6.6 0.016 VLXPG065
80 3” 94.0 76.0 6.6 0.018 VLXPG075
100 4” 122.5 100.5 6.6 0.024 VLXPG100
Material: TFMTM PTFE enveloppe / FPM core; TFMTM is a registered trademark of Dyneon
Colour: Translucent outside / black inside
FDA conformity certificate on request available
On request cam & groove seals made of anti-microbiological rubber available

a1-c&g 9/18/07 1:58 PM Pagina 39
A.1.
CAM & GROOVE SEALS

THREAD SEAL - PTFE
ND Inch OD Ø mm ID Ø mm Height mm Weight/pc Reference

kg
20 3/4” 26.0 19.0 1.5 0.001 X2RP020
25 1” 33.0 24.0 2.0 0.002 X2RP025
32 1.1/4” 42.0 33.0 2.0 0.002 X2RP032
40 1.1/2” 48.0 39.0 2.0 0.003 X2RP038
50 2” 60.0 49.0 2.0 0.004 X2RP050
65 2.1/2” 76.0 63.0 2.5 0.006 X2RP065
80 3” 88.0 77.0 3.0 0.010 X2RP075
100 4” 114.0 100.0 3.0 0.015 X2RP100
Material: PTFE
Colour: White
Seal dimensions in compliance with EN 14420-5
FED MIL / EN / DIN

THREAD SEAL - PU
ND Inch OD Ø mm ID Ø mm Height mm Weight/pc Reference

kg
20 3/4” 26.0 19.0 1.5 0.001 X2RV020
25 1” 33.0 24.0 2.0 0.001 X2RV025
32 1.1/4” 42.0 33.0 2.0 0.001 X2RV032
40 1.1/2” 48.0 39.0 2.0 0.001 X2RV038
50 2” 60.0 49.0 2.0 0.002 X2RV050
65 2.1/2” 76.0 63.0 2.5 0.003 X2RV065
80 3” 88.0 77.0 3.0 0.005 X2RV075
100 4” 114.0 100.0 3.0 0.008 X2RV100
Material: PU
Colour: Brown
Seal dimensions in compliance with EN 14420-5

a1-c&g 9/18/07 1:58 PM Pagina 40
CAM & GROOVE ACCESSORIES
STANDARD HANDLE

Kg
15 - 20 1/2” - 3/4” Stainless steel 0.02 VLHRPR1
25 1” Stainless steel 0.03 VLHRPR2
32 - 65 1.1/4” - 2.1/2” Stainless steel 0.06 VLHRPR3
80 - 100 3” - 4” Stainless steel 0.11 VLHRPR4
150 6” Stainless steel 0.25 VLHRPR6
25 1” Brass 0.04 VLHRPM2

32-65 1.1/4” - 2.1/2” Brass 0.08 VLHRPM3
80-125 3” - 5” Brass 0.10 VLHRPM4
150 6” Brass 0.26 VLHRPM6
Standard handle: Handle stainless steel AISI 304 - 1.4301

Safety pin stainless steel AISI 304 - 1.4301
SAFETY REBUILDING SET

Kg
25 1” Stainless steel 0.10 VLHRPR2S
32 - 65 1.1/2” - 2” Stainless steel 0.13 VLHRPR3S
80 - 100 3” -4” Stainless steel 0.17 VLHRPR4S
Safety rebuilding set: Safety handle stainless steel AISI 304 - 1.4301
Safety pin stainless steel AISI 304 - 1.4301 VLHRPR2S VLHRPR4S SAFETY
Safety hook stainless steel AISI 304 - 1.4301 VLHRPR3S HOOK
PULL RING
ND Inch Nr of wires ID mm OD mm Material Weight/pc Reference

kg
15 - 65 1/2” - 2.1/2” 2 30.0 34.0 Stainless steel 0.005 VLRR1
80 - 150 3” - 6” 3 30.0 34.5 Stainless steel 0.007 VLRR2
Stainless steel AISI 304 - 1.4301

a1-c&g 9/18/07 1:59 PM Pagina 41
A.1.
CAM & GROOVE ACCESSORIES

PIN

Kg
15-20 1/2” - 3/4” Stainless steel AISI 304 0.002 VLPR1
25 1” Stainless steel AISI 304 0.004 VLPR2
32-65 1.1/4” - 2.1/2” Stainless steel AISI 304 0.008 VLPR3
80-100 3” - 4” Stainless steel AISI 304 0.014 VLPR4
S-HOOK
Material Weight/pc Reference

Kg
Stainless steel AISI 304 0.002 KETRS
Brass 0.002 KETMS
FED MIL / EN / DIN

SAFETY PIN
Material Weight/pc Reference

Kg
Galvanized steel 0.018 VLBVS2
Stainless steel AISI 304 0.018 VLBVR2
CHAIN WITH S-HOOK
Length Material Weight/pc Reference

mm Kg
200 Stainless steel AISI 304 0.015 KETR200
150 Brass 0.013 KETM150
CAP L-HANDLE 90°

Kg
32-65 1.1/4” - 2.1/2” Stainless steel AISI 304 0.08 VLHRPR3L
80-100 3” - 4” Stainless steel AISI 304 0.16 VLHRPR4L
150 6” Stainless steel AISI 304 0.27 VLHRPR6L
L-handle: Patented handle stainless steel AISI 304 - 1.4301

Pull ring: stainless steel AISI 304 - 1.4301
Safety pin: stainless steel AISI 304 - 1.4301

a1-c&g 9/18/07 1:59 PM Pagina 42

Cam & Groove Couplings: Standard Federal Mil A-A-59326A

Uploaded by

Copyright:

Available Formats

Cam & Groove Couplings: Standard Federal Mil A-A-59326A

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Cam & Groove Couplings: Standard Federal Mil A-A-59326A

Uploaded by

Copyright:

Available Formats

a1-c&g 9/18/07 1:46 PM Pagina 1

CAM & GROOVE COUPLINGS FED MIL / EN / DIN

CAM & GROOVE COUPLINGS

Interchangeability with other brands

FED MIL / EN / DIN

The European standard EN 14420-7 was approved by CEN in September

Cam & groove couplings produced to EN 14420-7 are interchangeable with

Couplings produced to DIN 2828 are interchangeable with those produced

CAM & GROOVE COUPLINGS FED MIL / EN / DIN

1 7. Marked with diameter

3 10 11 12 12. Coupling insurance by brand name LMC-Couplings®

A.1.2 Chapter A: Quick couplings

CAM & GROOVE COUPLINGS FED MIL / EN / DIN

CAM & GROOVE COUPLINGS

FED MIL / EN / DIN

Stainless steel: ASTM A666 grade 316 / 1.4401

Chapter A: Quick couplings A.1.3

CAM & GROOVE COUPLINGS FED MIL / EN / DIN W W W . L M C - C O U P L I N G S . C O M

Materials and sizes

INCH 1/2” 3/4”-2” 2.1/2” 3”-4” 5”-6” 8”

Open envelope seal

A.1.4 Chapter A: Quick couplings

CAM & GROOVE COUPLINGS FED MIL / EN / DIN W W W . L M C - C O U P L I N G S . C O M

Closed envelope seal

CAM & GROOVE COUPLINGS

FED MIL / EN / DIN

REF. ASTM POLYMER TRADE NAME HARDNESS °C °F + PROPERTIES -

Chapter A: Quick couplings A.1.5

CAM & GROOVE COUPLINGS FED MIL / EN / DIN W W W . L M C - C O U P L I N G S . C O M

BSP = British Standard Pipe thread

THREAD DESCRIPTION STANDARD TYPICAL CALL OUT SEALING METHOD PROPERTIES

Cam & groove threads

COUPLING TYPE STANDARD ON REQUEST

Female threaded A BSP EN ISO 228-1 NPT ANSI B 1.20.1

Female threaded D BSP EN ISO 228-1 NPT ANSI B 1.20.1

A.1.6 Chapter A: Quick couplings

CAM & GROOVE COUPLINGS FED MIL / EN / DIN W W W . L M C - C O U P L I N G S . C O M

CAM & GROOVE COUPLINGS

Adaptor and coupler dimensions

Adaptor and coupler dimensions

FED MIL / EN / DIN

Chapter A: Quick couplings A.1.7

CAM & GROOVE COUPLINGS FED MIL / EN / DIN W W W . L M C - C O U P L I N G S . C O M

0.0 2.5 5.0 7.5 10.0 12.5 15.0

BRAND PRODUCTION METHOD

A.1.8 Chapter A: Quick couplings

CAM & GROOVE COUPLINGS FED MIL / EN / DIN W W W . L M C - C O U P L I N G S . C O M

CAM & GROOVE COUPLINGS

9 89.37 89.33 91.79

FED MIL / EN / DIN

Chapter A: Quick couplings A.1.9

CAM & GROOVE COUPLINGS FED MIL / EN / DIN W W W . L M C - C O U P L I N G S . C O M

ECTFE (up to 1000µm)

PFA (up to 200µm)

PTFE (up to 40µm)

PVDF (up to 800µm)

A.1.10 Chapter A: Quick couplings

CAM & GROOVE COUPLINGS FED MIL / EN / DIN W W W . L M C - C O U P L I N G S . C O M

CAM & GROOVE COUPLINGS