Model HS35

DrawWorks Optical Encoder BEI Sensors 

This specially configured DrawWorks Model HS35 encoder combines rugged, heavy-duty
features into a unique through-shaft style for use as a winch-turns counter in the
DrawWorks system of oil rigs. It incorporates dual bearings and shaft seals for NEMA 4
and 13 (IP65) ratings, a hard-anodized metal housing and a sealed connector. It comes
with a standard 1”-14 diameter threaded connection and a convertible adapter that allows
its use in systems with a 5/8”-18 threaded connection. This encoder has an UL, cUL, and
ATEX/CENELEC intrinsically safe rating when installed with the proper barriers (refer to
BEI P/N 924-60004-XXX series on the back of this specification sheet). This barrier is
high performance, galvanically isolated and carries US and European agency approvals.
It is suitable for ALL Hazardous locations, regardless of gas and dust types.

EN 55011 and EN 61000-6-2 CENELEC EEX ia IIC T4

U.S. Standards Class I, Group A,B,C & D; Canadian Standards

Class II Group E, F & G Class I, Zone 0, Group IIC

Mechanical Specifications Electrical Specifications Environmental Specifications

Shaft Bore: 0.375” diameter through with Code: Incremental Enclosure Rating: NEMA 4/13 (IP65)
convertible adapter for 1” or 5/8” air coupler. Output Format: 2 channels (A and B) in Temperature: -40° to +80°C standard
Starting Torque at 25°C: 7in-oz quadrature ± 27° electrical, with index and Shock: 50 G/s for 11 msec duration
Shaft Material: 416 stainless steel complements (see figure 1) Vibration: 5 to 2000 Hz @ 20 G’s
Bearing Housing: Die cast aluminum Cycles Per Shaft Turn: Up to 5,000 (see Humidity: 98% RH without condensation
Bearing Life: 7.5 x109 revs (50,000 hrs at Table A)
2500 RPM) Supply Voltage: 5 or 9V
Maximum RPM: 6,000 RPM (also see Current Requirements: 120mA (typical)
frequency response) Output Device: 5V/OC, 9V/OC,
Moment of Inertia: 0.019 oz-in-sec2 5V/OCR,40mA max current sink; 5 or 5V/V
Weight: Approximately 18 oz. line driver 100mA source/sink; 5V only
Frequency Response: 150kHz
Output Termination Pinouts: See Table 1

HS35 DrawWorks Ordering Options for assistance, call 800.350.2727

Use this diagram, working from left to right to construct your model number (example: HS35F-1-14-SS-200-ABZC-4469-SM18-EX-S)
All notes and tables referred to can be found on the back of this page.  

HS35F SS SM18 S

THREADING: CYCLES PER TURN: COMPLEMENTS: CONNECTOR:

1-14= 1” threaded bore (Enter cycles) See C= Complementary SM18= MS3102F18S-1P,
1-14L= 1” threaded bore Table A outputs (5V/V) 10 Pin Connector
100-S= 1” straight bore INTRINSIC SAFETY:
EX= Intrinsically safe rated
OUTPUT IC: encoder. Must be installed
SHAFT SEAL: NO. OF CHANNELS:
TYPE: 5V/OC: (open collector) with proper IS barriers
SS= Shaft Seal A= Single Channel
Hollow Shaft 3.5” 9V/OC: (open collector)
AB= Dual Channel in Quadrature SPECIAL FEATURES:
Diameter 5V/OCR: (open collector
ABZ= Dual Channel w/Index For shaft insert assembly, add –S to model number
AZ= Single Channel w/Index with internal pull-
and specify one of the following P/N on your
up resistor)
Purchase Order.
5V/V: (line driver)
31386-001: 1”-14 threads on both ends
31386-002: 1”-14 threads on female end, 5/8”-18
threads on male end
31386-003: 1”-14 threads on female end, 5/8”-18
threads on male end and adapter nut

Tel:805-968-0782 / 800-350-2727 | Fax: 805-968-3154 / 800-960-2726

7230 Hollister Ave., Goleta, CA 93117 | www.beisensors.com
Specification No. 02093-001 Rev. 06/11
 
 Model HS35
BEI Sensors 
DrawWorks Optical Encoder
Figure 1 Table 1 Table A
Output Waveforms  Output Terminations  Disc Resolutions
1 CYCLE (cycles per turn)
PIN ABZ ABZC 32, 100, 250, 360, 500, 512, 600, 1000, 1024,
90 Deg. 1200, 1650, 1800, 2000, 2048, 2100, 2500,
A CH A CH A 2881, 2884, 3600, 3710, 4096, 5000
HI
All the Components You Need
A LO B CH B CH B
for a Complete Solution for Any
C INDEX, Z INDEX, Z Hazardous Environment—
B
All from One Source
D +V SUPPLY VOLTAGE
Z
E —

A F 0V/ (CIRCUIT COMMON)

G CASE GROUND
B
H N/C A
Z
I N/C CH B

CCW Rotation Viewing Face J N/C CH Z

HS35 DrawWorks Dimensions  You no longer need to search through a

TOLERANCES: .XX = ±0.01, .XXX = ±0.005 stack of catalogs, mixing and matching
MS Connector Termination
sensors and barriers. With BEI’s ATEX-
approved components you can put
together a full system—encoder, cable
and barrier—with complete confidence
that all components will work together
perfectly. Integrating all three differential
data inputs, as well as power and ground
into a single, galvanically isolated barrier
reduces both engineering and installation
time. What’s more, this complete system
is Intrinsically Safe rated for ALL Gas and
Dust groups. Let us provide you with one
complete system that’s easy to specify,
easy to install, and can be used
anywhere.
BEI Intrinsic Safety Barrier
SUPPLY OUTPUT TYPE BARRIER
VOLTAGE TO FROM PART
BARRIER BARRIER NUMBER
12-24 VDC Vout = 5 VDC 924-60004-002
12-24 VDC Vout = Vin 924-60004-003
Vout = Open
12-24 VDC 924-60004-004
Collector
M18 Cable Assembly:
Part # Cable Length
924-31186-1810 10 feet
924-31186-1820 20 feet
These commodities, technology or software if exported from the United States must be in accordance with the 924-31186-1830 30 feet
Bureau of Industry, and Security, Export Administration regulations. Diversion contrary to U.S law is prohibited.
924-31186-1850 50 feet
Tel:805-968-0782 / 800-350-2727 | Fax: 805-968-3154 / 800-960-2726
7230 Hollister Ave., Goleta, CA 93117 | www.beisensors.com
Specification No. 02093-001 Rev. 06/11