Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Week 2 Secured

Download as pdf or txt
Download as pdf or txt
You are on page 1of 10

v1

ho / H

Fire: Condition of flash over Fire: process of combustion


QAT
time of burning W
330 A H
No flash over conditions (empirical)
Aw H 1/2  0.8 m5/2 also correpond to rate of buring
of 80 g / s for wood
Beyond above limit, lower limit of burning for flash
over condition, is a function of ventilation factor as

m&lim it 50.0  33.3 Aw H 1/ 2 g / s


B. Bhattacharjee B. Bhattacharjee
2 3
DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI

v1 v1
ho / H ho / H

Fire: process of combustion Fire: process of combustion


q&c q&L  q&w  q&R  q&B ; q&R rate of heat loss by radiation
q&c rate of heat release due to combustion through the openings;
q&L rateof heat loss due to replacement of q&B rate of heat storage in the gas;
hot gases by cold; (small generally neglected).
q&w rate of heat loss through the walls,
ceiling and floor;
B. Bhattacharjee B. Bhattacharjee
4 5
DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI
v1 v1
ho / H ho / H

Fire: Condition of flash over Fire: Condition of flash over


q&c 0.09 Aw H 1/ 2 'H c q&L m&F c pF (Tg  To )
q&R Aw  F V (T g4  T04 ) k W Mass flow rate of gases is assumed to same as air
inlet rate
T g4 ? T04 ; V 5.67 u 10  8 W / m 2 / o K 4 1
m&F m&air 0.52 AW H 2

q&R Aw  F V T 4
g
F 1  exp(  KxF )
q&L 0.52c pF (Tg  Ta ) Aw H 1/2
xF Flame thickness
K emission coefficient 1.1

B. Bhattacharjee B. Bhattacharjee
6 7
DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI

v1
ho / H

Fire: Condition of flash over Fire: process of combustion


Conduction heat loss is model through heat diffusion
equation and can be treated using Finite difference

The gas temperature Tg is unknown, conductivity is


function of temperature hence non-linear problem
can be solved by trial and error to estimate gas
temperature

Results obtained by Patterson is given

B. Bhattacharjee B. Bhattacharjee
8 9
DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI
Fire: process of combustion Fire: process of combustion

B. Bhattacharjee B. Bhattacharjee
10 11
DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI

General Outline Concrete


• Cement hydrates (binder) + aggregates.
™ Effect of fire on materials. • Cement hydrates is C-S-H gel structure.
Specific surface of cement (Blains
method) is about 300 m2/kg.
The hydrates have a very high surface
area, 1000 times that of cement, hence
surface forces have a major role to play
and surface forces start dominating the
properties.
B. Bhattacharjee
B. Bhattacharjee
2 DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI
DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI
Concrete Concrete On Heating
C-S-H has got water bonded chemically, it At 100ºc to 150ºc – capillary water
also has gel pores which contain ‘gel evaporates. There is no structure change,
water’ and there are larger capillary only some surface energy has been
pores.. added, which will make it try to absorb
water.
At 200 - 400ºc – the adsorbed water is
Hence we can say C-S-H gel has
lost. There will now be shrinkages and
chemically bonded water. since it is under restraint, there will be
Adsorbed water (gel water, held by fine cracks. The gel structure will start to
surface forces) collapse.
B. Bhattacharjee B. Bhattacharjee
DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI

Concrete on heating Concrete on heating


At 400 - 600ºc – the heat starts attacking Beyond 300ºc the residual strength
the water, which bonded chemically and reduces progressive till at 800ºc there is
the cementing property is lost.(this is an no structure. Spalling will be seen at
irreversible reaction.). 800ºc.
At 600 - 800ºc – the Ca(OH)2 (which was a If aggregate has CaCO3 contact, at 600ºc
by product of hydration).breaks down to the CaCO3 gives CaO + CO2 . The reaction
CaO + H2O. now the entire concrete has can be explosive in nature.
degenerated completely.

B. Bhattacharjee B. Bhattacharjee
DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI
Materials Concrete Materials Concrete

B. Bhattacharjee B. Bhattacharjee
8 9
DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI

Materials Concrete Steel on heating


Steel is an alloy Fe – C.
During fire there is thermal expansion
and at 550ºc, steel loses most of its
structure, hence if it is still loaded, it will
warp. Once cooled, it will regain some
structure, but cannot regain its original
structure and strength.
Fire resistance of mild steel is the time
required for the steel to reach 550ºc.

B. Bhattacharjee
B. Bhattacharjee
10 DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI
DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI
Materials Steel Materials Steel

B. Bhattacharjee B. Bhattacharjee
12 13
DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI

Timber on heating Timber on heating


Wood is cellulose embedded in lignin. If large surface area of wood is
The cellulose is a long chain molecule. exposed to heat, then pyrolysis
When heated, the long chain may break takes place.
and cross linking may occur, this is Charring occurs in logs where entire
charring (usually seen in logs).
wood is not exposed to high
If the long chains disintegrate then
temperature immediately.
volatile gases takes place and the timber
burns. When occurs some structure is
retained.
B. Bhattacharjee B. Bhattacharjee
DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI
Plastics on heating Plastics on heating
They don’t have a fixed melting
point. The important feature of polymer is
They soften and over a period of the gases or smoke they produce
time, and melt. can be toxic with cyanide gases.
(Tg) is glass transition temperature
for thermoplastics.

B. Bhattacharjee B. Bhattacharjee
DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI

Structures Gypsum

B. Bhattacharjee B. Bhattacharjee
18 19
DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI
Gypsum Steel members
Encasing in Concrete
Gypsum(CaSO4.2H2O) this is very useful
since it will absorb a lot of heat while
losing the water and the remaining CaSO4
is also a good insulator. Gypsum boards
are used.
Water column: the columns are
interconnected to an overhead tank which
also has a vent for vapour escape.
B. Bhattacharjee
B. Bhattacharjee DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI
20
DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI

Water filled column Water filled column

B. Bhattacharjee B. Bhattacharjee
22 23
DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI
General Outline Design for fire Resistance
Temperature attained = 550ºC – failure.
Reinforced concrete: Temperature of
™ Designing for Fire resistance. rebar = 550ºc – failure.
™ Steel member Conductivity of concrete is very low of
™ Fire resistant steel the order of 1 -2 W/mºC
IS code: more fire resistance dictates
more cover, but cannot be increased
indefinitely. More the cover, more the
strain in the steel, also extra material.
.
B. Bhattacharjee
B. Bhattacharjee
2 DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI
DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI

v1 v1
ho / H ho / H
DESIGN FOR FIRE RESISTANCE
DESIGN FOR FIRE RESISTANCE (STEEL)
Design of a simple Steel section for fire
resistance: Heat transfer to steel
‘l’ = thickness of the material . Qin = AsHV[(Tg i+1 +273)4 – (Ts i +273)4]ǻt +
Tg = Ta + 345(log 8t +1) hc As [(Tg i+1 – Ts i)] ǻt kW
The steel section is engulfed in fire. This will cause an increase in the heat
content of the steel = ȡs VCs(Ts i+1 – Tsi).
= Q stored

B. Bhattacharjee B. Bhattacharjee
4 5
DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI
v1 v1
ho / H ho / H

DESIGN FOR FIRE RESISTANCE DESIGN FOR FIRE RESISTANCE


Example: Section as shown
By equating Heat input Qin to heat stored Example: box Section as shown 200mm u
Qstored , we can work out the time required 200mm with thickness of 15 mm engulfed
for the temperature required for the in fire from all sides
temperature of steel TS to reach 550ºc. Properties: H =0.65
V=5.71e-8;ȡs =7850kg/cu.m
hc=0.023 kW/sq.m qK
Cs= 0.54kJ/kg

B. Bhattacharjee B. Bhattacharjee
6 7
DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI

v1
ho / H

DESIGN FOR FIRE RESISTANCE


Assume time step of 120 secs and
ambient temperature of 25 qC.
A=AsHV[(Tg i+1 +273)4 – (Ts i +273)4]/ ȡs VCs
B= hc As [(Tg i+1 – Ts i)] / ȡs VCs
After first step temperature is 64 and
after 2nd it is 119.
After 8 steps temperature is 555 deg C.
Thus Fire resistance is 16 minutes

B. Bhattacharjee
8
DEPARTMENT OF CIVIL ENGINEERING, IIT DELHI

You might also like