Cat SircoverBypass-gb PDF
Cat SircoverBypass-gb PDF
Cat SircoverBypass-gb PDF
svr_099_b_1_cat
SIRCOVER BY-PASS
svr_059_a_1_cat
appli_114_a
Changeover switches with fully visualised breaking
from 125 to 3200 A
• SIRCOVER with 3 stable positions (I, O, II) are 3 or 4 pole devices from 125 A
to 3200 A. They are available enclosed in a steel or polyester enclosure from
125 to 1600 A.
• A connection kit for copper bars allows the link between the 2 connection
terminals of one pole (fig 1 and 2) and the bridging of the upstream and
downstream link for ratings 2000, 2500 and 3200A (fig 3).
acces_231_a_1_cat
acces_226_c_2_cat
SIRCOVER I-0-II
svr_051_a_1_cat
(1)
3P 4100 3013
125 A
4P 4100 4013(1)
3P 3P
3P 4100 3016(1) 2694 3014(5)(6) 1509 3012(7)
160 A 4109 0019
4P 4100 4016(1) 4P 4P
2694 4014(5)(6) 1509 4012(7)
3P 4100 3019
200 A
4P 4100 4019 Type S2
(1)
200 mm
3P 4100 3025 Black IP55 1400 1020
250 A Black 4109 0025 3P 3P
1421 2113
4P 4100 4025(1) 4199 5012(2) 2694 3021(5)(6) 1509 3025(7)
320 mm
(1) Black IP65 1400 1032(2)
3P 4100 3039 4P 4P
400 A 1423 2113(2) 4109 0039 2694 4021(5)(6) 1509 4025(7)
4P 4100 4039(1)
3P 4100 3063(1) 4P 4P
630 A 4109 0063 2694 4051(5)(6) 1509 4063(7)
4P 4100 4063(1)
3P 4100 3080(1)
800 A 4109 0080 3P
4P 4100 4080(1) 1509 3080(7)
3P 4100 3120(1) 4P
1 250 A 200 mm 4109 0120 1509 4080(7)
4P 4100 4120(1) S4 type 1401 1520
Black
Black IP65
2799 7052(2)
3P 4100 3160(1) 1443 3113(2) 320 mm
1 600 A 1401 1532(2) 3P
4P 4100 4160(1) 1509 3160(7)
4109 0160
3P 4100 3180 4P
1 800 A 1509 4160(7)
4P 4100 4180
3P 4100 3200
2 000 A
4P 4100 4200 1st contact
NO/NC
3P 4100 3250 included
Black Black IP65 320 mm (3)
2 500 A included
4P 4100 4250 2799 7012(2) 2799 7146(2) 2799 3018(2)
2nd contact
NO/NC
3P 4100 3320 4409 0022(4)
3 200 A
4P 4100 4320
* 1 piece required per pole.
(1) Available enclosed (see pages 498 and 500 "Enclosed changeover switches").
(2) Standard.
(3) See page 281 "Copper bars connection kits".
(4) 2 pieces: one for position I and one for position II.
(5) To shroud front switch top and bottom 2 references required.
(6) To fully shroud front, rear, top and bottom 4 references required.
(7) 2 pieces: one for top side and another for bottom side.
SIRCOVER I - I+II - II
svr_051_a_1_cat
Shaft for
No. of External external Auxiliary Terminal Terminal
Rating (A) poles Switch body Direct handle handle handle Bridging bar* contacts shrouds screens
3P 4190 3013(1)
125 A
4P 4190 4013(1)
3P 3P
3P 4190 3016(1)
2694 3014(4)(5) 1509 3012(6)
160 A 4109 0019
4P 4P
4P 4190 4016(1)
2694 4014(4)(5) 1509 4012(6)
3P 4190 3019
200 A
4P 4190 4019
200 mm
3P 4190 3025(1) S2 type
Black 1400 1020
250 A Black IP65 4109 0025
4199 5012(2) 320 mm 3P 3P
4P 4190 4025(1) 1423 2114(2)
1400 1032(2) 2694 3021(4)(5) 1509 3025(6)
4P 4P
3P 4190 3039(1)
2694 4021(4)(5) 1509 4025(6)
400 A 4109 0039
4P 4190 4039(1)
1st/2nd contact
3P 4190 3050(1)
NO/NC
500 A 4109 0050
4109 0021(3) 3P 3P
4P 4190 4050(1)
2694 3051(4)(5) 1509 3063(6)
4P 4P
3P 4190 3063(1)
2694 4051(4)(5) 1509 4063(6)
630 A 4109 0063
4P 4190 4063(1)
3P 4190 3080(1)
800 A 4109 0080
3P
4P 4190 4080(1)
1509 3080(6)
4P
3P 4190 3120(1)
200 mm 1509 4080(6)
1 250 A 4109 0120
4P 4190 4120(1) S4 type 1401 1520
Black
Black IP65
2799 7052(2)
3P 4190 3160(1) 1443 3114(2) 320 mm
1 600 A 1401 1532(2) 3P
4P 4190 4160(1)
1509 3160(6)
4109 0160
4P
3P 4190 3180
1509 4160(6)
1 800 A
4P 4190 4180
* 1 piece required per pole.
(1) Available enclosed (see pages 498 and 500 "Enclosed changeover switches").
(2) Standard.
(3) 2 pieces: one for position I and one for position II.
(4) To fully shroud front, rear, top and bottom 4 references required.
(5) To shroud front switch top and bottom 2 references required.
(6) 2 pieces: one for top side and another for bottom side.
SIRCOVER BY-PASS
svr_059_a_4_cat
Shaft for
No. of Switch body External external Auxiliary Terminal Terminal
Rating (A) poles I-0-II Direct handle handle handle Bridging bar contacts shrouds screens
SIRCOVER BY-PASS
acces_129_b_1_cat
acces_153_a_2_cat
SIRCOVER
Switching External
S4 type handle Rating (A) type IP(1) Handle Reference
125 … 630 I - 0 - II IP55 S2 type 1421 2113
125 … 630 I - 0 - II IP65 S2 type 1423 2113
S3 type handle 125 … 630 I - I+II - II IP65 S2 type 1423 2114
800 … 1800 I - 0 - II IP65 S4 type 1443 3113(2)
800 … 1800 I - I+II - II IP65 S4 type 1443 3114(2)
S2 type handle 2000 … 3200 I - 0 - II IP65 2799 7146(2)
(1) IP: Degree of protection according to standard IEC 60529.
(2) Double lever handle.
acces_150_a_1_cat
acces_151_a_1_cat
acces_152_a_2_cat
SIRCOVER BY-PASS
Switching External
Rating (A) type IP(1) Handle Reference
125 … 200 I - 0 - II IP55 S2 type 1421 2113
125 … 200 I - 0 - II IP65 S2 type 1423 2113
250 ... 630 I - 0 - II IP65 S3 type 1433 3113
800 … 1600 I - 0 - II IP65 4199 7146
(1) IP: Degree of protection according to standard IEC 60529.
Use Dimensions
Enables S type handles to be fitted in place Adds 12 mm to the depth.
of existing older style Socomec handles.
Adapter can also be utilised as a spacer to
increase the distance between the panel
door and the handle lever.
acces_187_a_1_cat
To be ordered
Color in multiples of External IP(1) Reference
Black 10 IP65 1493 0000
(1) IP: Degree of protection according to standard IEC 60529.
Description Reference
Shaft guide 1429 0000
SIRCOVER
Shaft length Dimension X
Rating (A) (mm) (mm) Reference
125 … 400 200 mm 210 … 310 1400 1020
125 … 400 320 mm 210 … 430 1400 1032
500 … 630 200 mm 280 … 390 1400 1020
acces_144_b_1_cat
SIRCOVER BY-PASS
Shaft length Dimension X
Rating (A) (mm) (mm) Reference
acces_202_a_1_cat
Bridging bars
acces_208_a_2_cat
svr_068_a_1_x_cat
252
74 74
37 37 60
Top or bottom flat connection - Fig. 1
acces_232_a_1_cat
Quantity to order
155
Fig. 3
Top or bottom bridging connection -Fig. 3
B
Quantity to order
Rating (A) Piece per pole(1) Reference
acces_230_b_1_x_cat
(1) Example for 3 pole device equipped upstream only: order 3 times the indicated quantities.
(2) Bolt set is provided with the accessories.
Characteristics
Operating current Ie (A)
Nominal A - 250 400 VAC 24 VDC 48 VDC
Rating (A) current (A) -13VAC AC-13 DC-13 DC-13
125 … 3200 16 12 8 14 6
Terminal shrouds
Use Advantage
Protection against direct contact with Perforations allowing remote
terminals or connecting parts. thermographic inspection without removal.
No. of
Rating (A) poles Position Reference
125 … 200 3P top / bottom / front (I) / rear (II) 2694 3014(1)(2)
125 … 200 4P top / bottom / front (I) / rear (II) 2694 4014(1)(2)
250 … 400 3P top / bottom / front (I) / rear (II) 2694 3021(1)(2)
250 … 400 4P top / bottom / front (I) / rear (II) 2694 4021(1)(2)
500 … 630 3P top / bottom / front (I) / rear (II) 2694 3051(1)(2)
500 … 630 4P top / bottom / front (I) / rear (II) 2694 4051(1)(2)
(1) To shroud front switch top and bottom 4 references required for a SIRCOVER and 6
acces_206_a_2_cat
Terminal screens
Use
Top or bottom protection against direct contact with terminals or connection parts.
Use
Safety isolating separation between the terminals, essential for use at 690 VAC
or in a polluted or dusty atmosphere.
The terminal shrouds also provide phase separation from 125 to 630 A.
125 to 500 A
Thermal current Ith (40°C) 125 A 160 A 200 A 250 A 400 A 500 A
Rated insulation voltage Ui (V) 800 800 800 800 800 1000
Rated impulse withstand voltage Uimp (kV) 8 8 8 8 8 12
Overload capacity
Rated short-time withstand current 0.3 s. ICW (kA eff.) 15 15 15 17 17 25
Rated peak withstand current (kA peak) (6) 20 20 20 30 30 45
Connection
Minimum Cu cable section (mm2) 35 50 50 95 185 240
Minimum Cu busbar section (mm2)
Maximum Cu cable section (mm2) 50 95 95 150 240 240
Maximum Cu busbar width (mm) 25 25 25 32 32 40
Tightening torque min (Nm) 9 9 9 20 20 20
Mechanical characteristics
Durability (number of operating cycles)(7) 10 000 10 000 10 000 10 000 10 000 5 000
Weight of 3 P switch (kg) 1.5 1.6 1.8 2 3 3.5
Weight of 4 P switch (kg) 1.6 1.7 1.9 2.1 3.5 4
(1) Category with index A = frequent operation - Category with index B = infrequent operation.
(2) With terminal shrouds or phase barrier.
(3) 3-pole device with 2 pole in series for the "+" and 1 pole for the "-".
(4) 4-pole device with 2 pole in series by polarity.
(5) The power value is given for information only, the current values vary from one manufacturer to another.
(6) For a rated operational voltage Ue = 400 VAC.
(7) Increased endurances: please consult us.
630 to 3200 A
Thermal current Ith (40°C) 630 A 800 A 1250 A 1600 A 1800 A 2000 A 2500 A 3200 A
Rated insulation voltage Ui (V) 1000 1000 1000 1000 1000 1000 1000 1000
Rated impulse withstand voltage Uimp (kV) 12 12 12 12 12 12 12 12
Overload capacity
Rated short-time withstand current 0.3 s. ICW (kA eff.) 25 50 65 100 100 100 100 110
Rated peak withstand current (kA peak) (6) 45 55 80 110 110 110 110 120
Connection
Minimum Cu cable section (mm2) 2 x 150 2 x 185
Minimum Cu busbar section (mm2) 2 x 30 x 5 2 x 40 x 5 2 X 60 X 5 2 x 80 x 5 2 x 80 x 5 3 x 100 x 5 4 x 100 x 5 4 x 100 x 5
Maximum Cu cable section (mm2) 2 x 300 2 x 300 4 X 185 6 x 185 6 x 185
Maximum Cu busbar width (mm) 50 63 63 100 100 125 125 125
Tightening torque min (Nm) 20 20 40 40 40 40 40
Mechanical characteristics
Durability (number of operating cycles)(7) 5 000 3 000 3 000 4 000 4 000 3 000 3 000 3 000
Weight of 3 P switch (kg) 3.5 17.5 22.5 34 34 50 50 50
Weight of 4 P switch (kg) 4 21 27.5 42 42 60 60 60
(1) Category with index A = frequent operation - Category with index B = infrequent operation.
(2) With terminal shrouds or phase barrier.
(3) 3-pole device with 3 pole in series for the "+" and 1 pole for the "-".
(4) 4-pole device with 2 pole in series per polarity.
(5) The power value is given for information only, the current values vary from one manufacturer to another.
(6) For a rated operational voltage Ue = 400 VAC.
(7) Increased endurances: please consult us.
A Z1
10 M Z
II
Y Y B
U 8.5 1
W
CA
V
2
A
350
AC
BA
AA
II I
0
125
L1
svr_072_i_1_x_cat
CA
H HA
X T T T H E min.
I
60 45
J C 18
Terminal
Overall dimensions shrouds Switch body Switch mounting Connection
Rating A A J J M M X X
(A) 3p. 4p. C E min AC H HA 3p. 4p. 3p. 4p. N T U V W 3p. 4p. Y Z Z1 AA BA AC
125 221 251 218 208 ... 436 235 148 25 182 212 156 186 101 36 20 25 8.5 56 50 3,5 28 124 135 115 10
160 221 251 218 208 ... 436 235 148 25 182 212 156 186 101 36 20 25 8.5 56 50 3,5 28 124 135 115 10
200 221 251 218 208 ... 436 235 148 25 182 212 156 186 101 36 20 25 8.5 56 50 3,5 28 124 135 115 10
250 262 312 218 208 ... 436 280 148 25 223 273 196 246 116 50 25 30 11 61 61 3,5 30 124 160 130 15
400 262 312 218 208 ... 436 280 148 25 223 273 196 246 116 50 35 35 11 61 61 3,5 30 124 170 140 15
500 319 379 295 285 ... 513 401 225 25 272 332 246 306 176 65 32 37 13 70.5 65.5 5 43 180 235 205 15
630 319 379 295 285 ... 513 400 225 25 272 332 246 306 176 65 45 50 13 70.5 65.5 5 43 180 260 220 20
800 386 466 375 425 ... 577 459 298 29 306.5 386.5 255 336 250 80 50 60.5 15 48 48 7 66.5 253.5 321 26.5
1250 386 466 375 425 ... 577 459 298 29 306.5 386.5 255 336 250 80 60 65 16x11 48 48 7 66.5 255.5 330 29.5
1600 478 598 375 425 ... 577 461 298 29 306.5 388.5 347 467 250 120 90 43.5 12.5x5 54 54 8 66.5 255.5 288 15
1800 478 598 375 425 ... 577 461 298 29 388.5 518.5 347 467 250 120 90 43.5 12.5x5 54 54 8 66.5 255.5 288 15
A
M 51.5 436.5
=
330
330
461
258
250
380
=
svr_128_c_1_x_cat
A Z2
10 M Z1
1
Z
II
U 8.5 Y Y Y
W
CA
V
2
AC
BA
AA
N
I II I
0
L1
CA
X T T T H
I
J C 18
=
250 to 630 A
A B C C. External double lever handle: 800 to 1600 A
330
1. Terminal shrouds
2. Direct handle operation:
- 125 to 200 A: L1 = 140 mm,
125
=
- 800 to 1600 A: L1 = Ø 330 mm.
210
svr_070_i_1_x_cat
H HA 45
E min. 103
61
Terminal
Overall dimensions shrouds Switch body Switch mounting Connection
A A E J J M M X X
Rating (A) 3+6p. 4+8p. C min AC H HA 3+6 p. 4+8 p. 3+6 p. 4+8 p. N T U V W 3+6p. 4+8p. Y Z Z1 Z2 AA BA AC
125 221 251 313 320 235 243 25 182 212 156 186 101 36 20 25 8,5 56 50 3.5 28 124 219 135 115 10
160 221 251 313 320 235 243 25 182 212 156 186 101 36 20 25 8,5 56 50 3.5 28 124 219 135 115 10
200 221 251 313 320 235 243 25 182 212 156 186 101 36 20 25 8,5 56 50 3.5 28 124 219 135 115 10
250 262 312 313 298 280 243 25 223 273 196 246 116 50 25 30 11 61 61 3.5 30 124 219 160 130 10
400 262 312 313 298 280 243 25 223 273 196 246 116 50 35 35 11 61 61 3.5 30 124 219 170 140 15
500 319 379 432 417 401 362 25 272 332 246 306 176 65 32 37 13 70.5 65.5 5 43 180 317 235 205 15
630 319 379 432 417 400 362 25 272 332 246 306 176 65 45 50 13 70.5 65.5 5 43 180 317 260 220 20
800 386 466 560 550 459 479 29 306.5 386.5 255 335 250 80 50 60.5 15 48 48 7 66.5 253.5 439.5 321 26.5
1250 386 466 560 550 459 479 29 306.5 386.5 255 335 250 80 60 65 16x11 48 48 7 66.5 253.5 439.5 320 29.25
1600 478 598 560 550 461 479 29 388.5 518.5 347 467 250 120 90 43.5 12.5x5 54 54 8 66.5 253.5 439.5 288 15
Connection terminals
SIRCOVER and SIRCOVER BY-PASS 800 A SIRCOVER and SIRCOVER BY-PASS 1250 A SIRCOVER 1600 to 3200 A
SIRCOVER BY-PASS 1600 A
ø9 16 x 11
ø12.5
5 5
12.5
10 33
15 28.5
ø 15
15
svr_078_b_1_x_cat
svr_077_a_1_x_cat
svr_098_a_1_x_cat
25 25
8.5 33 8.5 15.75 28.5 15.75 30 30
45 45
50 60 90
Front operation
Handle type Direction of operation Door drilling
S2 type 0 With lock With lock
o RONIS EL11AP CASTELL K
I+II 20 20
Ø 26 Ø 37
Ø78 90
° 4 Ø 5.5
28
90
4Ø7 2 Ø 6.5
28
.5
Ø 37 Ø 37
I II 4Ø7 4Ø7
1414
125
24
22
14 14
14 14
26
45
.5
svr_138_a_1_gb_cat
79
45°
45°
73
3.
Ø D (1)
5
20 20 20 20
Front operation
Handle type Direction of operation Door drilling
S4 type With lock With lock
0
20 20 RONIS EL11AP CASTELL K
or
I+II
Ø 26 Ø 37
4 Ø 7 (2)
90 4 Ø 5.5
28
Ø78 2 Ø 6.5
°
28
°
.5
90
Ø 37 Ø 37
350
1414
4Ø7 4Ø7
I II
24
22
14 14
14 14
26
Ø D (1)
svr_139_a_1_gb_cat
.5
79
45°
45°
73
3.
5
20 20 20 20
60
Front operation
Handle type Direction of operation Door drilling
C type With lock
CASTELL K
50 50
II 96
° 28
90
4 Ø 6.5
300
0
25
50
50
90
svr_140_a_1_gb_cat
I
Ø 31 4 x Ø 6.5 Ø 31 3 x Ø 6.5
Front operation
Handle type Direction of operation Door drilling
S2 type With lock With lock
0 RONIS EL11AP CASTELL K
90 20 20
°
° Ø 26
90 Ø 37
Ø78
4 Ø 5.5
28
4Ø7 2 Ø 6.5
28
.5
I II Ø 37 Ø 37
4Ø7 4Ø7
1414
125
24
22
14 14
14 14
26
svr_141_a_1_gb_cat
45
.5
79
45°
45°
73
3.
Ø D (1)
5
20 20 20 20
(1) Ø31 to Ø37: rear screw mounting Ø37: front clip mounting.
Front operation
Handle type Direction of operation Door drilling
S3 type 0 With lock With lock
RONIS EL11AP CASTELL K
90 20 20
°
°
90
Ø78 Ø 26 Ø 37
4Ø7 4 Ø 5.5
28
2 Ø 6.5
28
.5
I II
Ø 37 Ø 37
4Ø7 4Ø7
1414
210
24
22
14 14
14 14
26
svr_142_a_1_gb_cat
.5
79
45°
45°
Ø D (1)
73
3.
5
61 20 20 20 20
(1) Ø31 to Ø37: rear screw mounting Ø37: front clip mounting.
Front operation
Handle type Direction of operation Door drilling
C type With lock
CASTELL K
50 50
II 96
° 28
90
4 Ø 6.5
300
0
25
50
50
90
svr_143_a_1_gb_cat
I Ø 31
4 x Ø 6.5 Ø 31 3 x Ø 6.5