Bahan Reading Hydraulic Pneumatic
Bahan Reading Hydraulic Pneumatic
Bahan Reading Hydraulic Pneumatic
G. H. Waghmare
Professor, Mechanical Engineering, Yeshwantrao Chavan College of Engineering, Nagpur, India.
ABSTRACT
In general we use three methods for transmitting power from one point to another. Mechanical
transmission is through shafts, gears, chains, belts, etc. Electrical transmission is through wires,
transformers, etc. Fluid power is through liquids or gas in a confined space. We shall discuss a
structure of hydraulic systems and pneumatic systems. We will also discuss the advantages and
disadvantages and compare hydraulic, pneumatic, and mechanical systems. Fluid power is the
technology that deals with the generation, control and transmission of forces and movement of
mechanical element or system with the use of pressurized fluids in a confined system. Both liquids
and gases are considered fluids. In this article the energy analysis of the pneumatic system is
implemented in the simulation model. Previous research has shown the comparison of methods for
the investigation on the energetic behaviour of pneumatic drives and its practical application.
Concerning the analysis of the methods for determination the energy efficiency, the presented
model is based on exergy analysis.
Key words: Exergy, Gases, Hydraulic, liquid, Pneumatic.
Cite this Article: Aakash M Bodh and Prof. G.H. Waghmare, Study, Design and Improvement of
Pumping System Efficiency of Hydraulic Pneumatic Reciprocating Pump. International Journal of
Mechanical Engineering and Technology, 7(5), 2016, pp. 127–132.
http://www.iaeme.com/ijmet/issues.asp?JType=IJMET&VType=7&IType=5
1. INTRODUCTION
Fluid power system includes a hydraulic system (hydra meaning water in Greek) and a pneumatic system
(pneuma meaning air in Greek). Oil hydraulic employs pressurized liquid petroleum oils and synthetic oils,
and pneumatic employs compressed air that is released to the atmosphere after performing the work.
Perhaps it would be in order that we clarify our thinking on one point. By the term “fluid” we refer to air or
oil, for it has been shown that water has certain drawbacks in the transmission of hydraulic power in
machine operation and control. Commercially, pure water contains various chemicals (some deliberately
included) and also foreign matter, and unless special precautions are taken when it is used, it is nearly
impossible to maintain valves and working surfaces in satisfactory condition. In the cases where the
hydraulic system is closed (i.e., the one with a self-contained unit that serves one machine or one small
group of machines), oil is commonly used, thus providing, in addition to power transmission, benefits of
lubrication not afforded by water as well as increased life and efficiency of packings and valves. It should
be mentioned that in some special cases, soluble oil diluted with water is used for safety reasons. The
application of fluid power is limited only by the ingenuity of the designer, production engineer or plant
engineer. If the application pertains to lifting, pushing, pulling, clamping, tilting, forcing, pressing or any
other straight line (and many rotary) motions, it is possible that fluid power will meet the requirement.
Fluid power applications can be classified into two major segments:
Stationary hydraulics: Stationary hydraulic systems remain firmly fixed in one position. The
characteristic feature of stationary hydraulics is that valves are mainly solenoid operated. The applications
of stationary hydraulics are as follows: Production and assembly of vehicles of all types. Machine tools
and transfer lines. Lifting and conveying devices. Metal-forming presses. Plastic machinery such as
injection-molding machines. Rolling machines. Lifts. Food processing machinery. Automatic handling
equipment and robots. Mobile hydraulics: Mobile hydraulic systems move on wheels or tracks such as a
tower crane or excavator truck.
4. LITERATURE SURVEY
• Paper named” Process simulation of energy behaviour of pneumatic drives" says that In this article the
energy analysis of the pneumatic system is implemented in the simulation model. Previous research has
shown the comparison of methods for the investigation on the energetic behaviour of pneumatic drives and
its practical application .Concerning the analysis of the methods for determination the energy efficiency, the
presented model is based on exergy analysis. Exergy analysis is able to consider all energy losses as well as
the influence of the temperature behaviour on the available useful pneumatic energy.
• Paper named” Design of High Speed Rotary Valves for Pneumatic Applications "says that Valves based on
rotating geometry have long been sought by designers for their simplicity, compactness, and desirable
dynamic properties. Unfortunately, they generally involve tight sealing surfaces with significant relative
motion, making them particularly prone to problems of wear, leakage, and seizure. These inherent
weaknesses are easily overcome in applications involving low pressures or low actuation speeds but become
more significant in applications with high pressures and/or high speeds.
• Paper named “Controller Design for Simulation Control of Intelligent Pneumatic Actuators (IPA) System
says that Intelligent Pneumatic Actuators (IPA) is a system for application that requires better control and
accuracy. The purpose of this paper is to present a controller design for simulation control of an IPA system
using Proportional-Integrative (PI) controller and pole-placement feedback controller. Before the controller
is designed, model identification is used to obtain the plant using transfer function. The flow for the
controller design starts with the theory, mathematical calculation, procedures and the implementation of the
simulation control by using MATLAB software. Furthermore, simulation results are compared and analyzed
to illustrate the performance of the proposed controllers.
5. OPERATING EFFICIENCIES
5.1. General
Water pumping stations will normally operate automatically to satisfy the hydraulic requirements of the
system. Supervisory or remote control of electric motors will be provided on the larger installations to
reduce operator time and to provide a means for optimal control of energy costs, and to allow for energy
conservation measures. For optimal control of energy costs, particularly for larger pump stations, the
control system will allow the operators to schedule pump operations so that station electrical consumption
is minimized at the same time adequate storage for fire protection and system pressures are maintained.
Energy costs comprise the major component of the operating costs of water supply systems. The largest
quantity of energy is usually consumed by treated water pumping stations. The overall operating cost
associated with a particular pump station will be dependent upon the following factors: the pumps, the
distribution system, the pump drivers, and the governing energy rate schedule. The design analysis for the
distribution system and pump station and the cost evaluation will consider these factors.
6. ANALYSIS FIGURES
Following results shows Total deformation and total stress are under Permissible values
9. RESULTS
Thus we have studied hydraulic pneumatic reciprocating pump. When we use it for testing purpose, it can
be used for both hydraulic and pneumatic pumps. It is found more efficient.
From the simulation it is found that the pump is bearing an equivalent stress and also total deformation
is under desired limits.
REFERENCE
[1] Travis L. Brown, Prasad atlurijames P. Schmiedeler” Design of High Speed Rotary Valves For
Pneumatic Applications” Aerospace and Mechanical Engineering, University of Notre Dame,
Notre Dame, Indiana
[2] Elvira Rakova*, Jürgen Weber “Process simulation of energy behaviour of pneumatic drives” Dresden
University of Technology, Institute for Fluid Power (IFD), Helmholtzstr. 7a, D-01069 Dresden,
Germany
[3] Ahmad 'Athif Mohd Faudzia,*, Khairuddin bin Osmanb, M.F. Rahmatc, Nu'man Din Mustafaa, M.
Asyraf Azmana, Koichi Suzumori “Controller Design for Simulation Control of Intelligent Pneumatic
Actuators (IPA) system graduate School of Natural Science and Technology, Okayama University,
Okayama, Japan
[4] Bhaumika, A Kumaraswamyb,*, S Guruprasada “Design & development of test rig for investigation of
contact Mechanics phenomena in reciprocating hydraulic sealsar & DE ( Engrs.), Dighi, Pune, 411015,
India B defence Institute of Advanced Technology (DU), Girinagar, Pune, 411025, India
[5] Nilesh Bodkhe, Sanghshil L. Kanekar and Tushar G. Bhore, Design, Analysis & Fabrication of
Pneumatic Material Handling System. International Journal of Mechanical Engineering and
Technology (IJMET), 6(8), 2015, pp.12–23.
[6] Wang, W. & Gao, Z. (2003). A comparison study of advanced state observer design techniques.
Proceedings of the American Control Conference, Denver, Colorado, USA,pp. 4754-4759.
[7] Vivas, A. & Mosquera, V. (2005). Predictive functional control of a PUMA robot. ICGST,ACSE 05
Conference, Cairo, Egypt, pp. 372-387.
[8] Rodriguez-Angeles, A. & Nijmeijer, H. (2004). Synchronizing Tracking Control for Flexible Joint
Robots via Estimated State Feedback. ASME Journal of Dynamic Systems,
[9] Mohd. Rehan Khan and Dr. Ajeet Kumar Rai, An Experimental Study of Exergy in A Corrugated Plate
Heat Exchanger. International Journal of Mechanical Engineering and Technology (IJMET), 6(11),
2015, pp.16–22.