LM7900

Product Order Technical Tools & Support &
Folder Now Documents Software Community
LM158, LM158A, LM258, LM258A

LM358, LM358A, LM358B, LM2904, LM2904B, LM2904V
SLOS068V – JUNE 1976 – REVISED SEPTEMBER 2018
Industry-Standard Dual Operational Amplifiers

1 Features 3 Description
•
1 Wide Supply Range of 3 V to 36 V (B Version) The LM358B and LM2904B devices are the next-
• Supply-Current of 300 µA (B Version, Typical) generation versions of the industry-standard LM358
and LM2904 devices, which include two high-voltage
• Unity-Gain Bandwidth of 1.2 MHz (B Version)
(36-V) operational amplifiers (op amps). These
• Common-Mode Input Voltage Range Includes devices provide outstanding value for cost-sensitive
Ground, Enabling Direct Sensing Near Ground applications, with features including low offset
• Low Input Offset Voltage of 3 mV at 25°C (A and (300 µV, typical), common-mode input range to
B Versions, Maximum) ground, and high differential input voltage capability.
• Internal RF and EMI Filter (B Version) The LM358B and LM2904B devices simplify circuit
• On Products Compliant to MIL-PRF-38535, All design with enhanced features such as unity-gain
Parameters Are Tested Unless Otherwise Noted. stability, lower offset voltage of 3 mV (maximum at
room temperature), and lower quiescent current of
On All Other Products, Production Processing
300 µA (typical). High ESD (2 kV, HBM) and
Does Not Necessarily Include Testing of All integrated EMI and RF filters enable the LM358B and
Parameters. LM2904B devices to be used in the most rugged,
environmentally challenging applications.
2 Applications
The LM358B and LM2904B devices are available in
• Merchant Network and Server Power Supply Units micro-size packages, such as TSOT-8 and WSON,
• Multi-Function Printers as well as industry standard packages, including
• Power Supplies and Mobile Chargers SOIC, TSSOP, and VSSOP.
• Motor Control: AC Induction, Brushed DC, Device Information(1)
Brushless DC, High-Voltage, Low-Voltage, PART NUMBER PACKAGE BODY SIZE (NOM)
Permanent Magnet, and Stepper Motor
LM358B(2), LM2904B(2),
• Desktop PC and Motherboard LM358, LM358A,LM2904, SOIC (8) 4.90 mm × 3.90 mm
LM2904V, LM258, LM258A
• Indoor and Outdoor Air Conditioners
LM358, LM358A, LM2904,
• Washers, Dryers, and Refrigerators LM2490V
TSSOP (8) 3.00 mm × 4.40 mm
• AC Inverters, String Inverters, Central Inverters, LM358, LM358A LM2904,
VSSOP (8) 3.00 mm × 3.00 mm
and Voltage Frequency Drives LM2904V, LM258, LM258A
• Uninterruptible Power Supplies LM358, LM2904 SO (8) 5.20 mm × 5.30 mm
• Programmable Logic Controllers LM358, LM2904, LM358A,
PDIP (8) 9.81 mm × 6.35 mm
LM258, LM258A
• Electronic Point-of-Sale Systems
LM158, LM158A CDIP (8) 9.60 mm × 6.67 mm
Single-Pole, Low-Pass Filter LM158, LM158A LCCC (20) 8.89 mm × 8.89 mm
RG RF (1) For all available packages, see the orderable addendum at

the end of the data sheet.
(2) Package is for preview only
R1 VOUT
VIN
C1
1
f-3 dB =
2pR1C1
VOUT
VIN (
= 1+
RF
RG (( 1
1 + sR1C1 (
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. UNLESS OTHERWISE NOTED, this document contains PRODUCTION
DATA.
LM158, LM158A, LM258, LM258A
SLOS068V – JUNE 1976 – REVISED SEPTEMBER 2018 www.ti.com
Table of Contents
1 Features .................................................................. 1 9.1 Overview ................................................................. 17
2 Applications ........................................................... 1 9.2 Functional Block Diagram ....................................... 17
3 Description ............................................................. 1 9.3 Feature Description................................................. 18
9.4 Device Functional Modes........................................ 18
4 Revision History..................................................... 2
5 Device Comparison Table..................................... 4 10 Application and Implementation........................ 19
10.1 Application Information.......................................... 19
6 Pin Configuration and Functions ......................... 5
10.2 Typical Application ............................................... 19
7 Specifications......................................................... 6
11 Power Supply Recommendations ..................... 20
7.1 Absolute Maximum Ratings ...................................... 6
7.2 ESD Ratings.............................................................. 6 12 Layout................................................................... 20
12.1 Layout Guidelines ................................................. 20
7.3 Recommended Operating Conditions....................... 7
12.2 Layout Examples................................................... 21
7.4 Thermal Information .................................................. 7
7.5 Electrical Characteristics: LM358B and LM358BA ... 8 13 Device and Documentation Support ................. 22
7.6 Electrical Characteristics: LM2904B and 13.1 Documentation Support ........................................ 22
LM2904BA ................................................................. 9 13.2 Related Links ........................................................ 22
7.7 Electrical Characteristics: LM358, LM358A ............ 10 13.3 Receiving Notification of Documentation Updates 22
7.8 Electrical Characteristics: LM2904, LM2904V ........ 11 13.4 Community Resources.......................................... 22
7.9 Electrical Characteristics: LM158, LM158A ............ 12 13.5 Trademarks ........................................................... 22
7.10 Electrical Characteristics: LM258, LM258A .......... 13 13.6 Electrostatic Discharge Caution ............................ 22
7.11 Typical Characteristics .......................................... 14 13.7 Glossary ................................................................ 23
8 Parameter Measurement Information ................ 16 14 Mechanical, Packaging, and Orderable
9 Detailed Description ............................................ 17 Information ........................................................... 23
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision U (January 2017) to Revision V Page
• Changed the data sheet title ................................................................................................................................................. 1

• Changed first four items in the Features section ................................................................................................................... 1
• Changed the first item in the Applications section and added four new items ...................................................................... 1
• Changed voltage values in the first paragraph of the Description section ............................................................................. 1
• Changed text in the second paragraph of the Description section......................................................................................... 1
• Added devices LM358B and LM2904B to data sheet ............................................................................................................ 1
• Changed the first three rows of the Device Information table and added a a cross-referenced note for PREVIEW-
status devices ......................................................................................................................................................................... 1
• Added Device Comparison table ........................................................................................................................................... 4
• Added a table note to the Pin Functions table ...................................................................................................................... 5
• Changed "free-air temperature" to "ambient temperature" in the Absolute Maximum Ratings condition statement ............. 6
• Changed all entries in the Absolute Maximum Ratings table except TJ and Tstg .................................................................. 6
• Deleted lead temperature and case temperature from Absolute Maximum Ratings.............................................................. 6
• Changed device listings and their voltage values in the ESD Ratings table ......................................................................... 6
• Changed "free-air temperature" to "ambient temperature" in the Recommended Operating Conditions condition
statement ............................................................................................................................................................................... 7
• Changed table entries for all parameters in the Recommended Operating Conditions table ................................................ 7
• Added rows to the Thermal Information table, and a table note regarding device-package combinations .......................... 7
• Added two Electrical Characteristics tables with five additional devices, and redistributed the seven original devices
differently among the tables ................................................................................................................................................... 8
• Deleted the Operating Conditions table................................................................................................................................ 13
• Added a condition statement to the Typical Characteristics section .................................................................................... 14
• Changed specific voltages to a Recommended Operating Conditions reference ............................................................... 17
2 Submit Documentation Feedback Copyright © 1976–2018, Texas Instruments Incorporated
Product Folder Links: LM158 LM258 LM258A LM358 LM358A LM358B LM2904 LM2904B LM2904V
LM158, LM158A, LM258, LM258A
www.ti.com SLOS068V – JUNE 1976 – REVISED SEPTEMBER 2018
Revision History (continued)

• Changed unity-gain bandwidth from 0.7 MHz for all devices to 1.2 MHz for B-version devices.......................................... 18
• Changed slew rate from.3 V/µs for all devices to o.5 V/µs for B-version devices................................................................ 18
• Changed the Input Common Mode Range section in multiple places throughout ............................................................... 18
• Changed VCC to VS in the Application Information section .................................................................................................. 19
• Subscripted the suffixes fro RI and RF .................................................................................................................................. 19
• Changed Operational Amplifier Board Layout for Noninverting Configuration with an image that includes a dual op amp 21
• Added Preview designation to the LM358B and LM2904B devices in Table 1 ................................................................... 22
Changes from Revision T (April 2015) to Revision U Page
• Changed data sheet title......................................................................................................................................................... 1

• Added Receiving Notification of Documentation Updates section and Community Resources section ............................. 22
Changes from Revision S (January 2014) to Revision T Page
• Added Applications section, ESD Ratings table, Feature Description section, Device Functional Modes, Application
and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation
Support section, and Mechanical, Packaging, and Orderable Information section ............................................................... 1
Changes from Revision R (July 2010) to Revision S Page
• Converted this data sheet from the QS format to DocZone using the PDF on the web ........................................................ 1
• Deleted Ordering Information table ........................................................................................................................................ 1
• Updated Features to include Military Disclaimer .................................................................................................................... 1
• Added Typical Characteristics section.................................................................................................................................. 14
• Added ESD warning ............................................................................................................................................................. 23
Copyright © 1976–2018, Texas Instruments Incorporated Submit Documentation Feedback 3

LM158, LM158A, LM258, LM258A
5 Device Comparison Table

SUPPLY TEMPERATURE VOS (MAXIMUM IQ / CH (TYPICAL AT INTEGRATED EMI
PART NUMBER PACKAGE
VOLTAGE RANGE AT 25°C) 25°C) FILTER
LM358B 3 V–36 V –40°C to 85°C 3 mV 300 µA Yes D, PW
LM2904B 3 V–36 V –40°C to 125°C 3 mV 300 µA Yes D, PW
LM358 3 V–32 V 0°C to 70°C 7 mV 350 µA No D, PW, DGK, P, PS
LM2904 3 V–26 V –40°C to 125°C 7 mV 350 µA No D, PW, DGK, P, PS
LM358A 3 V–32 V 0°C to 70°C 3 mV 350 µA No D, PW, DGK, P
LM2904V 3 V–32 V –40°C to 125°C 3 mV 350 µA No D, PW
LM158 3 V–32 V –55°C to 125°C 5 mV 350 µA No JG, FK
LM158A 3 V–32 V –55°C to 125°C 3 mV 350 µA No JG, FK
LM258 3 V–32 V –25°C to 85°C 5 mV 350 µA No D, DGK, P
LM258A 3 V–32 V –25°C to 85°C 3 mV 350 µA No D, DGK, P
LM158, LM158A, LM258, LM258A
6 Pin Configuration and Functions
D, DGK, P, PS, PW, and JG Packages

8-Pin SOIC, VSSOP, PDIP, SO, TSSOP, and CDIP FK Package
Top View 20-Pin LCCC
Top View
OUT1
NC
NC
NC
V+
OUT1 1 8 V+
IN1± 2 7 OUT2
20
19
IN1+ 3 6 IN2±
NC 4 18 NC
V± 4 5 IN2+
IN1± 5 17 OUT2
NC 6 16 NC
Not to scale
IN1+ 7 15 IN2±
NC 8 14 NC
10
11
12
13
9
Not to scale
NC
V±
NC
IN2+
NC
NC - No internal connection
Pin Functions
PIN I/O DESCRIPTION
SOIC, SSOP, CDIP, PDIP, SO,
NAME LCCC (1)
TSSOP, CFP (1)
IN1– 5 2 I Negative input
IN1+ 7 3 I Positive input
IN2– 15 6 I Negative input
IN2+ 12 5 I Positive input
OUT1 2 1 O Output
OUT2 17 7 O Output
Negative (lowest) supply or ground (for single-
V– 10 4 —
supply operation)
1, 3, 4, 6, 8, 9, 11,
NC — — No internal connection
13, 14, 16, 18, 19
V+ 20 8 — Positive (highest) supply
(1) For a listing of which devices are available in what packages, see Device Comparison Table.

LM158, LM158A, LM258, LM258A
7 Specifications
7.1 Absolute Maximum Ratings
over operating ambient temperature range (unless otherwise noted) (1)
MIN MAX UNIT
LM358B, LM358BA,
–0.3 ±20 or 40
LM2904B, LM2904BA
LM158, LM258, LM358,
Supply voltage, VS = ([V+] – [V–]) V
LM158A, LM258A, LM358A, –0.3 ±16 or 32
LM2904V
LM2904 –0.3 ±13 or 26
LM358B, LM358BA,
LM2904B, LM2904BA,LM158,
–32 32
Differential input voltage, VID (2) LM258, LM358, LM158A, V
LM258A, LM358A, LM2904V
LM2904 –26 26
LM358B, LM358BA,
–0.3 40
LM2904B, LM2904BA
LM158, LM258, LM358,
Input voltage, VI Either input V
LM158A, LM258A, LM358A, –0.3 32
LM2904V
LM2904 –0.3 26
Duration of output short circuit (one amplifier) to ground at (or below) TA = 25°C,
Unlimited s
VS ≤ 15 V (3)
LM158, LM158A –55 125
LM258, LM258A –25 85
LM358B, LM358BA –40 85
Operating ambient temperature, TA °C
LM358, LM358A 0 70
LM2904B, LM2904BA,
–40 125
LM2904, LM2904V
Operating virtual-junction temperature, TJ 150 °C
Storage temperature, Tstg –65 150 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) Differential voltages are at IN+, with respect to IN−.
(3) Short circuits from outputs to VS can cause excessive heating and eventual destruction.
7.2 ESD Ratings

VALUE UNIT
LM358B, LM358BA, LM2904B, AND LM2904BA
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) ±2000
V(ESD) Electrostatic discharge V
Charged-device model (CDM), per JEDEC specification JESD22-C101 (2) ±750
LM158, LM258, LM358, LM158, LM258A, LM358A, LM2904, AND LM2904V
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) ±500
V(ESD) Electrostatic discharge (2)
V
Charged-device model (CDM), per JEDEC specification JESD22-C101 ±1000
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
LM158, LM158A, LM258, LM258A
7.3 Recommended Operating Conditions

over operating ambient temperature range (unless otherwise noted)
MIN MAX UNIT
LM358B, LM358BA, LM2904B,
3 36
LM2904BA
VS Supply voltage, VS= ([V+] – [V–]) LM158, LM258, LM358, LM158A, V
3 30
LM258A, LM358A, LM2904V
LM2904 3 26
VCM Common-mode voltage V– VS – 2 V
LM358B, LM358BA –40 85
LM2904B, LM2904BA, LM2904,
–40 125
LM2904V
TA Operating ambient temperature °C
LM358, LM358A 0 70
LM258, LM258A –20 85
LM158, LM158A –55 125
7.4 Thermal Information

LM258, LM258A, LM358, LM358A, LM358B, LM358BA, LM2904, LM158, LM158A
LM2904B, LM2904BA, LM2904V (2)
THERMAL METRIC (1) D DGK P PS PW FK JG UNIT
(SOIC) (VSSOP) (PDIP) (SO) (TSSOP) (LCCC) (CDIP)
8 PINS 8 PINS 8 PINS 8 PINS 8 PINS 20 PINS 8 PINS
RθJA Junction-to-ambient thermal
124.7 181.4 80.9 116.9 171.7 — — °C/W
resistance
RθJC(top) Junction-to-case (top)
66.9 69.4 70.4 62.5 68.8 5.61 14.5 °C/W
thermal resistance
RθJB Junction-to-board thermal
67.9 102.9 57.4 68.6 99.2 — — °C/W
resistance
ψJT Junction-to-top
19.2 11.8 40 21.9 11.5 — — °C/W
characterization parameter
ψJB Junction-to-board
67.2 101.2 56.9 67.6 97.9 — — °C/W
characterization parameter
RθJC(bot) Junction-to-case (bottom)
— — — — — 12.1 — °C/W
thermal resistance
(1) For more information about traditional and new thermal metrics, see Semiconductor and IC Package Thermal Metrics.
(2) For a listing of which devices are available in what packages, see Device Comparison Table

LM158, LM158A, LM258, LM258A
7.5 Electrical Characteristics: LM358B and LM358BA

For VS = (V+) – (V–) = 5 V to 36 V (±2.25 V to ±18 V), TA = 25 °C, RL = 10 kΩ connected to VS / 2, and VCM = VOUT = VS / 2
(unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP (1) MAX UNIT
OFFSET VOLTAGE
1 3
LM358B
TA = –40°C to 85°C 4
VOS Input offset voltage mV
0.5 1.8
LM358BA
TA = –40°C to 85°C 2.5
dVOS/dT Input offset voltage drift TA = –40°C to 85°C ±3.5 µV/°C
Power-supply rejection
PSRR ratio ±1 15 µV/V
(ΔVIO/ΔVS)
Channel separation, dc At dc 120 dB
INPUT VOLTAGE RANGE
Common-mode input (V–) (V+) – 1.5

VCM VS = 3 V to 36 V V
voltage range TA = –40°C to 85°C (V–) (V+) – 2
Common-mode rejection (V–) < VCM < (V+) – 1.5 V 80 103

CMRR dB
ratio (V–) < VCM < (V+) – 2 V TA = –40°C to 85°C 70 96
INPUT BIAS CURRENT
10 35
IB Input bias current nA
TA = –40°C to 85°C 50
0.5 4
IOS Input offset current nA
TA = –40°C to 85°C 5
NOISE
En Input voltage noise ƒ = 0.1 to 10 Hz 8 µVPP
en Input voltage noise density ƒ = 1 kHz 40 nV/√Hz
INPUT IMPEDANCE
ZID Differential 10 || 0.1 MΩ || pF
ZIC Common-mode 4 || 1.5 GΩ || pF
OPEN-LOOP GAIN
70 140
AOL Open-loop voltage gain VS = 15 V, VO = 1 V to 11 V, RL ≥ 2 kΩ V/mV
TA = –40°C to 85°C 35
FREQUENCY RESPONSE
GBW Gain-bandwidth product 1.2 MHz
SR Slew rate G = +1 0.5 V/µs
φm Phase margin G = +1, RL = 10 kΩ, CL = 20 pF 56 º
tS Settling time To 0.1%, VS = 5 V, 2-V step , G = +1, CL = 100 pF 4 µs
tOR Overload recovery time VIN × gain > VS 30 µs
Total harmonic distortion +
THD + N G = +1, ƒ = 1 kHz, VO = 3.53 VRMS, RL = 100 kΩ 0.001%
noise
OUTPUT
IOUT = 50 µA 1.35 1.5
Positive Rail (V+) IOUT = 1 mA 1.4 1.6
Voltage output swing from
VO IOUT = 5 mA 1.5 1.75 V
rail
IOUT = 50 µA 0.1 0.15
Negative Rail (V-)
IOUT = 1 mA 0.75 1
ISC Short-circuit current VS = 20 V ±40 60 mA
CLOAD Capacitive load drive 100 pF
Open-loop output
RO f = 1 MHz, IO = 0 A 300 Ω
resistance
POWER SUPPLY
Quiescent current per VS = 5 V; VO = 2.5 V; IO = 0 A 300 460

IQ µA
amplifier VS = 36 V; VO = 2.5 V; IO = 0 A TA = – 40°C to 85°C 800
(1) All typical values are TA = 25°C.
LM158, LM158A, LM258, LM258A
7.6 Electrical Characteristics: LM2904B and LM2904BA

For VS = (V+) – (V–) = 5 V to 36 V (±2.25 V to ±18 V), TA = 25 °C, RL = 10 kΩ connected to VS / 2, and VCM = VOUT = VS / 2
(unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP (1) MAX UNIT
OFFSET VOLTAGE
1 3
LM2904B
TA = –40°C to 125°C 4
0.5 1.8
LM2904BA
TA = –40°C to 125°C 2.5
dVOS/dT Input offset voltage drift TA = –40°C to 125°C ±3.5 µV/°C
Power-supply rejection ratio
PSRR ±1 15 µV/V
(ΔVIO/ΔVS)
Channel separation, dc At dc 120 dB
INPUT VOLTAGE RANGE
Common-mode input voltage (V–) (V+) – 1.5

VCM VS = 3 V to 36 V V
range TA = –40°C to 125°C (V–) (V+) – 2
(V–) < VCM < (V+) – 1.5 V 80 103
CMRR Common-mode rejection ratio dB
(V–) < VCM < (V+) – 2 V TA = –40°C to 125°C 70 96
INPUT BIAS CURRENT
10 35
IB Input bias current nA
TA = –40°C to 125°C 50
0.5 4
IOS Input offset current nA
TA = –40°C to 125°C 5
NOISE
En Input voltage noise ƒ = 0.1 to 10 Hz 8 µVPP
en Input voltage noise density ƒ = 1 kHz 40 nV/√Hz
INPUT IMPEDANCE
ZID Differential 10 || 0.1 MΩ || pF
ZIC Common-mode 4 || 1.5 GΩ || pF
OPEN-LOOP GAIN
70 140
AOL Open-loop voltage gain VS = 15 V; VO = 1 V to 11 V; RL ≥ 2 kΩ V/mV
TA = –40°C to 125°C 35
FREQUENCY RESPONSE
GBW Gain-bandwidth product 1.2 MHz
φm Phase margin G = +1, RL = 10 kΩ, CL = 20 pF 56 º
tS Settling time To 0.1%, VS = 5 V, 2-V step , G = +1, CL = 100 pF 4 µs
tOR Overload recovery time VIN × gain > VS 30 µs
Total harmonic distortion +
THD + N G = +1, ƒ = 1 kHz, VO = 3.53 VRMS, RL = 100 kΩ 0.001%
noise
OUTPUT
IOUT = 50 µA 1.35 1.5
Positive rail (V+) IOUT = 1 mA 1.4 1.6
VO Voltage output swing from rail IOUT = 5mA 1.5 1.75 V
IOUT = 50 µA 0.1 0.15
Negative rail (V–)
IOUT = 1 mA 0.75 1
ISC Short-circuit current VS = 20 V ±40 60 mA
CLOAD Capacitive load drive 100 pF
RO Open-loop output resistance f = 1 MHz, IO = 0 A 300 Ω
POWER SUPPLY
VS = 5 V; VO = 2.5 V; IO = 0 A 300 460
IQ Quiescent current per amplifier µA
VS = 36 V; VO = 2.5 V; IO = 0 A TA = –40°C to 125°C 800

LM158, LM158A, LM258, LM258A
7.7 Electrical Characteristics: LM358, LM358A

For VS = (V+) – (V–) = 5 V, TA = 25 °C, (unless otherwise noted)
PARAMETER TEST CONDITIONS (1) MIN TYP (2) MAX UNIT
OFFSET VOLTAGE
3 7
LM358
VS = 5 V to 30 V; VCM = 0 V; VO = 1.4 TA = 0°C to 70°C 9
V LM358A 2 3
TA = 0°C to 70°C 5
LM358 TA = 0°C to 70°C 7
dVOS/dT Input offset voltage drift µV/°C
LM358A TA = 0°C to 70°C 7 20
Input offset voltage vs power
PSRR VS = 5 V to 30 V 65 100 dB
supply (ΔVIO/ΔVS)
VO1/ VO2 Channel separation f = 1 kHz to 20 kHz 120 dB
INPUT VOLTAGE RANGE
VS = 5 V to 30 V LM358
(V–) (V+) – 1.5
VS = 30 V LM358A
VCM Common-mode voltage range V
VS = 5 V to 30 V LM358
TA = 0°C to 70°C (V–) (V+) – 2
VS = 30 V LM358A
CMRR Common-mode rejection ratio VS = 5 V to 30 V; VCM = 0 V 65 80 dB
INPUT BIAS CURRENT
–20 –250
LM358
TA = 0°C to 70°C –500
IB Input bias current VO = 1.4 V nA
–15 –100
LM358A
TA = 0°C to 70°C –200
2 50
LM358
TA = 0°C to 70°C 150
IOS Input offset current VO = 1.4 V nA
2 30
LM358A
TA = 0°C to 70°C 75
10
dIOS/dT Input offset current drift pA/°C
LM358A TA = 0°C to 70°C 300
NOISE
en Input voltage noise density f = 1 kHz 40 nV/√Hz
OPEN-LOOP GAIN
25 100
TA = 0°C to 70°C 15
FREQUENCY RESPONSE
GBW Gain bandwidth product 0.7 MHz
OUTPUT
VS = 30 V; RL = 2 kΩ TA = 0°C to 70°C 4
Positive rail VS = 30 V; RL ≥ 10 kΩ 2 3 V
VO Voltage output swing from rail
VS = 5 V; RL ≥ 2 kΩ 1.5
Negative rail VS = 5 V; RL ≤ 10 kΩ TA = 0°C to 70°C 5 20 mV
–20 –30
VS = 15 V; VO = 0 V; VID
Source LM358A –60
=1V
TA = 0°C to 70°C –10 mA
IO Output current 10 20
VS = 15 V; VO = 15 V;
Sink TA = 0°C to 70°C 5
VID = –1 V
LM358 12
µA
VID = –1 V; VO = 200 mV 30
ISC Short-circuit current VS = 10 V; VO = VS / 2 ±40 ±60 mA
POWER SUPPLY
Quiescent current per VO = 2.5 V; IO = 0 A 350 600

IQ TA = 0°C to 70°C µA
amplifier VS = 30 V; VO = 15 V; IO = 0 A 500 1000
(1) All characteristics are measured under open-loop conditions, with zero common-mode input voltage, unless otherwise specified.
Maximum VS for testing purposes is 30 V for LM358 and LM358A.
LM158, LM158A, LM258, LM258A
7.8 Electrical Characteristics: LM2904, LM2904V

OFFSET VOLTAGE
Non-A suffix 3 7
devices TA = –40°C to 125°C 10
VS = 5 V to maximum; VCM = 0 V; VO = 1.4
V 1 2
A-suffix
devices TA = –40°C to 125°C 4
dVOS/dT Input offset voltage drift TA = –40°C to 125°C 7 µV/°C
Input offset voltage vs power
PSRR VS = 5 V to 30 V 65 100 dB
supply (ΔVIO/ΔVS)
INPUT VOLTAGE RANGE
(V–) (V+) – 1.5
VCM Common-mode voltage range VS = 5 V to maximum V
TA = –40°C to 125°C (V–) (V+) – 2
CMRR Common-mode rejection ratio VS = 5 V to maximum; VCM = 0 V 65 80 dB
INPUT BIAS CURRENT
–20 –250
TA = –40°C to 125°C –500
Non-V suffix 2 50
device TA = –40°C to 125°C 300
V-suffix 2 50
device TA = –40°C to 125°C 150
dIOS/dT Input offset current drift TA = –40°C to 125°C 10 pA/°C
NOISE
OPEN-LOOP GAIN
25 100
TA = –40°C to 125°C 15
FREQUENCY RESPONSE
OUTPUT
RL ≥ 10 kΩ VS – 1.5
VS = maximum; RL =
22
Non-V suffix 2 kΩ
device VS = maximum; RL ≥
23 24
Positive rail 10 kΩ V
VO Voltage output swing from rail TA = –40°C to 125°C
VS = maximum; RL =
26
2 kΩ
V-suffix device
VS = maximum; RL ≥
27 28
10 kΩ
Negative rail VS = 5 V; RL ≤ 10 kΩ TA = –40°C to 125°C 5 20 mV
–20 –30
VS = 15 V; VO = 0 V; VID = 1 V Source
TA = –40°C to 125°C –10
mA
10 20
IO Output current VS = 15 V; VO = 15 V; VID = –1 V Sink
TA = –40°C to 125°C 5
Non-V suffix device 30
VID = -1 V; VO = 200 mV µA
V-suffix device 12 40
POWER SUPPLY
VO = 2.5 V; IO = 0 A 350 600
IQ Quiescent current per amplifier TA = –40°C to 125°C µA
VS = maximum; VO = maximum / 2; IO = 0 A 500 1000
Maximum VS for testing purposes is 26 V for LM2904 and 32 V for LM2904V.

LM158, LM158A, LM258, LM258A

OFFSET VOLTAGE
3 5
LM158
TA = –55°C to 125°C 7
VOS Input offset voltage VS = 5 V to 30 V; VCM = 0 V; VO = 1.4 V mV
2
LM158A
TA = –55°C to 125°C 4
LM158 TA = –55°C to 125°C 7
LM158A TA = –55°C to 125°C 7 15 (3)
Input offset voltage vs power supply
PSRR VS = 5 V to 30 V 65 100 dB
(ΔVIO/ΔVS)
INPUT VOLTAGE RANGE
VS = 5 V to 30 V LM158
(V–) (V+) – 1.5
VS = 30 V LM158A
VS = 5 V to 30 V LM158
TA = –55°C to 125°C (V–) (V+) – 2
VS = 30 V LM158A
INPUT BIAS CURRENT
–20 –150
LM158
TA = –55°C to 125°C –300
–15 –50
LM158A
TA = –55°C to 125°C –100
2 30
LM158
TA = –55°C to 125°C 100
2 10
LM158A
TA = –55°C to 125°C 30
10
LM158A TA = –55°C to 125°C 200
NOISE
OPEN-LOOP GAIN
50 100
TA = –55°C to 125°C 25
FREQUENCY RESPONSE
SR Slew rate G = +1 V/µs
VS = 30 V; RL = 2 kΩ TA = –55°C to 125°C 4
VS = 5 V; RL ≥ 2 kΩ 1.5
–20 –30
VS = 15 V; VO = 0 V; VID = 1 V Source LM158A –60
TA = –55°C to 125°C –10 mA
IO Output current
VS = 15 V; VO = 15 V; VID = –1 10 20
Sink
V TA = –55°C to 125°C 5
VID = –1 V; VO = 200 mV 12 30 µA
POWER SUPPLY
VO = 2.5 V; IO = 0 A 350 600
VS = 30 V; VO = 15 V; IO = 0 A 500 1000
(3) On products compliant to MIL-PRF-38535, this parameter is not production tested.
LM158, LM158A, LM258, LM258A

OFFSET VOLTAGE
3 5
LM258
TA = –25°C to 85°C 7
VOS Input offset voltage VS = 5 V to 30 V; VCM = 0 V; VO = 1.4 V mV
2 3
LM258A
TA = –25°C to 85°C 4
LM258 TA = –25°C to 85°C 7
LM258A TA = –25°C to 85°C 7 15
Input offset voltage vs power supply
PSRR VS = 5 V to 30 V 65 100 dB
(ΔVIO/ΔVS)
INPUT VOLTAGE RANGE
VS = 5 V to 30 V LM258
(V–) (V+) – 1.5
VS = 30 V LM258A
VS = 5 V to 30 V LM258
TA = –25°C to 85°C (V–) (V+) – 2
VS = 30 V LM258A
INPUT BIAS CURRENT
–20 –150
LM258
TA = –25°C to 85°C –300
–15 –80
LM258A
TA = –25°C to 85°C –100
2 30
LM258
TA = –25°C to 85°C 100
2 15
LM258A
TA = –25°C to 85°C 30
10
LM258A TA = –25°C to 85°C 200
NOISE
OPEN-LOOP GAIN
50 100
TA = –25°C to 85°C 25
FREQUENCY RESPONSE
OUTPUT
VS = 30 V; RL = 2 kΩ TA = –25°C to 85°C 4
VS = 5 V; RL ≥ 2 kΩ 1.5
–20 –30
VS = 15 V; VO = 0 V; VID = 1 V Source LM258A –60
TA = –25°C to 85°C –10 mA
IO Output current
VS = 15 V; VO = 15 V; VID = –1 10 20
Sink
V TA = –25°C to 85°C 5
VID = –1 V; VO = 200 mV 12 30 µA
POWER SUPPLY
VO = 2.5 V; IO = 0 A 350 600
VS = 30 V; VO = 15 V; IO = 0 A 500 1000

LM158, LM158A, LM258, LM258A
7.11 Typical Characteristics

Typical characteristics section is applicable for LM158, LM158A, LM258, LM258A, LM358, LM358A, LM2904, and LM2904V
20 0.36
18 0.34 –55C
16 0C
0.32
Supply Current (mA)

Input Current (nAdc)
14 125C
12 0.3
10 0.28
8
0.26
6 5Vdc
15Vdc 0.24
4
30Vdc
2 0.22
0 0.2
–55 –35 –15 5 25 45 65 85 105 125 0 5 10 15 20 25 30
Temperature (°C) Supply Voltage (Vdc)
Figure 1. Input Current vs. Temperature Figure 2. Supply Current vs. Supply Voltage
160 100
RL=20K 90 CMRR
140
RL=2K 80
120
Avol Voltage Gain (dB)
70
100
CMRR (dB)
60
80 50
40
60
30
40
20
20 10
0 0
0 5 10 15 20 25 30 35 40 0.1 1 10 100 1000
V+ Supply Voltage (Vdc) Frequency (kHz) C001
Figure 3. Voltage Gain vs. Supply Voltage Figure 4. Common-Mode Rejection Ratio vs. Frequency
3.5 0.50
VOUT
3.0 0.45
2.5
0.40
Voltage (V)
Voltage (V)
2.0
0.35
1.5
0.30
1.0
0.25
0.5
VOUT
0.0 0.20
0 4 8 12 16 20 24 28 32 36 40 0 2 4 6 8 10
Time ( s) C001
Time ( s) C001
Figure 5. Voltage Follower Large Signal Response (50 pF) Figure 6. Voltage Follower Small Signal Response (50 pF)
LM158, LM158A, LM258, LM258A
Typical Characteristics (continued)

Typical characteristics section is applicable for LM158, LM158A, LM258, LM258A, LM358, LM358A, LM2904, and LM2904V
20 8
Output Voltage (Vdc) relative to Vcc

17.5 7
15
Output Swing (Vp-p)
6
12.5
5
10
4
7.5
3
5
2.5 2
0 1
1 10 100 1k 0.001 0.01 0.1 1 10 100
Frequency (kHz) Output Sink Current (mAdc)
Figure 7. Maximum Output Swing vs. Frequency Figure 8. Output Sourcing Characteristics
(VCC = 15 V)
10 90
5Vdc
80
15Vdc
30Vdc Output Current (mAdc) 70
Output Voltage (Vdc)
1 60
50
40
0.1 30
20
10
0.01 0
0.001 0.01 0.1 1 10 100 –55 –35 –15 5 25 45 65 85 105 125
Output Sink Current (mAdc) Temperature (°C)
Figure 9. Output Sinking Characteristics Figure 10. Source Current Limiting

LM158, LM158A, LM258, LM258A
8 Parameter Measurement Information

900 Ω
VCC+
VCC+
− 100 Ω
VO −
+ VI = 0 V
VI VO
RS
CL +
VCC− RL
VCC−
Figure 11. Unity-Gain Amplifier Figure 12. Noise-Test Circuit
LM158, LM158A, LM258, LM258A
9 Detailed Description
9.1 Overview
These devices consist of two independent, high-gain frequency-compensated operational amplifiers designed to
operate from a single supply over a wide range of voltages. Operation from split supplies also is possible if the
difference between the two supplies is within the supply voltage range specified in the Recommended Operating
Conditions section, and VS is at least 1.5 V more positive than the input common-mode voltage. The low supply-
current drain is independent of the magnitude of the supply voltage.
Applications include transducer amplifiers, dc amplification blocks, and all the conventional operational amplifier
circuits that now can be implemented more easily in single-supply-voltage systems. For example, these devices
can be operated directly from the standard 5-V supply used in digital systems and easily can provide the required
interface electronics without additional ±5-V supplies.
9.2 Functional Block Diagram
VCC+
≈6-µA ≈6-µA ≈100-µA

Current Current Current
Regulator Regulator Regulator
OUT
IN−
IN+ ≈50-µA
Current
Regulator
GND (or VCC−)
To Other Amplifier
COMPONENT COUNT
Epi-FET 1
Diodes 2
Resistors 7
Transistors 51
Capacitors 2

LM158, LM158A, LM258, LM258A
9.3 Feature Description

9.3.1 Unity-Gain Bandwidth
The unity-gain bandwidth is the frequency up to which an amplifier with a unity gain may be operated without
greatly distorting the signal. These devices have a 1.2-MHz unity-gain bandwidth (B Version).
9.3.2 Slew Rate

The slew rate is the rate at which an operational amplifier can change its output when there is a change on the
input. These devices have a 0.5-V/µs slew rate (B Version).
9.3.3 Input Common Mode Range

The valid common mode range is from device ground to VS – 1.5 V (VS – 2 V across temperature). Inputs may
exceed VS up to the maximum VS without device damage. At least one input must be in the valid input common-
mode range for the output to be the correct phase. If both inputs exceed the valid range, then the output phase is
undefined. If either input more than 0.3 V below V– then input current should be limited to 1 mA and the output
phase is undefined.
9.4 Device Functional Modes

These devices are powered on when the supply is connected. This device can be operated as a single-supply
operational amplifier or dual-supply amplifier, depending on the application.
LM158, LM158A, LM258, LM258A
10 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
10.1 Application Information

The LMx58 and LM2904 operational amplifiers are useful in a wide range of signal conditioning applications.
Inputs can be powered before VS for flexibility in multiple supply circuits.
10.2 Typical Application

A typical application for an operational amplifier is an inverting amplifier. This amplifier takes a positive voltage on
the input, and makes it a negative voltage of the same magnitude. In the same manner, it also makes negative
voltages positive.
RF
RI Vsup+
VOUT
+
VIN
Vsup-
Figure 13. Application Schematic
10.2.1 Design Requirements

The supply voltage must be chosen such that it is larger than the input voltage range and output range. For
instance, this application scales a signal of ±0.5 V to ±1.8 V. Setting the supply at ±12 V is sufficient to
accommodate this application.
10.2.2 Detailed Design Procedure

Determine the gain required by the inverting amplifier using Equation 1 and Equation 2:
VOUT
AV
VIN (1)
1.8
AV 3.6
0.5 (2)
Once the desired gain is determined, choose a value for RI or RF. [Subscripts should be fixed in the
accompanying figures and equations also.] Choosing a value in the kilohm range is desirable because the
amplifier circuit uses currents in the milliampere range. This ensures the part does not draw too much current.
This example uses 10 kΩ for RI which means 36 kΩ is used for RF. This was determined by Equation 3.
RF
AV
RI (3)

LM158, LM158A, LM258, LM258A
Typical Application (continued)

10.2.3 Application Curve
2
VIN
1.5
VOUT
1
0.5
Volts
0
-0.5
-1
-1.5
-2
0 0.5 1 1.5 2
Time (ms)
Figure 14. Input and Output Voltages of the Inverting Amplifier
11 Power Supply Recommendations
CAUTION
Supply voltages larger than specified in the recommended operating region can
permanently damage the device (see the Absolute Maximum Ratings).
Place 0.1-µF bypass capacitors close to the power-supply pins to reduce errors coupling in from noisy or high-
impedance power supplies. For more detailed information on bypass capacitor placement, see the Layout
section.
12 Layout
12.1 Layout Guidelines

For best operational performance of the device, use good PCB layout practices, including:
• Noise can propagate into analog circuitry through the power pins of the circuit as a whole, as well as the
operational amplifier. Bypass capacitors are used to reduce the coupled noise by providing low-impedance
power sources local to the analog circuitry.
– Connect low-ESR, 0.1-µF ceramic bypass capacitors between each supply pin and ground, placed as
close to the device as possible. A single bypass capacitor from V+ to ground is applicable for single-
supply applications.
• Separate grounding for analog and digital portions of circuitry is one of the simplest and most-effective
methods of noise suppression. One or more layers on multilayer PCBs are usually devoted to ground planes.
A ground plane helps distribute heat and reduces EMI noise pickup. Make sure to physically separate digital
and analog grounds, paying attention to the flow of the ground current.
• To reduce parasitic coupling, run the input traces as far away from the supply or output traces as possible. If
it is not possible to keep them separate, it is much better to cross the sensitive trace perpendicular as
opposed to in parallel with the noisy trace. [Things in parallel never cross, by definition]
• Place the external components as close to the device as possible. Keeping RF and RG close to the inverting
input minimizes parasitic capacitance, as shown in Layout Examples.
• Keep the length of input traces as short as possible. Always remember that the input traces are the most
sensitive part of the circuit.
• Consider a driven, low-impedance guard ring around the critical traces. A guard ring can significantly reduce
leakage currents from nearby traces that are at different potentials.
LM158, LM158A, LM258, LM258A
12.2 Layout Examples
Place components close to

device and to each other to
reduce parasitic errors
Run the input traces as far
VS+
away from the supply lines
as possible RF
OUT1 V+
RG
GND IN1í OUT2
GND
VIN IN1+ IN2í
R IN
Ví IN2+
Only needed for Use low-ESR, ceramic
dual-supply bypass capacitor
operation
VSí
GND
(or GND for single supply) Ground (GND) plane on another layer
Figure 15. Operational Amplifier Board Layout for Noninverting Configuration
RIN
VIN +
VOUT
RG
RF
Figure 16. Operational Amplifier Schematic for Noninverting Configuration

LM158, LM158A, LM258, LM258A
13 Device and Documentation Support
13.1 Documentation Support

13.1.1 Related Documentation
• Texas Instruments, Circuit Board Layout Techniques.
13.2 Related Links

The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to order now.
Table 1. Related Links

TECHNICAL TOOLS & SUPPORT &
PARTS PRODUCT FOLDER ORDER NOW
DOCUMENTS SOFTWARE COMMUNITY
LM158 Click here Click here Click here Click here Click here
LM158A Click here Click here Click here Click here Click here
(1)
LM358B Click here Click here Click here Click here Click here
LM2904B (1) Click here Click here Click here Click here Click here
LM2904V Click here Click here Click here Click here Click here
(1) Device is currently Preview
13.3 Receiving Notification of Documentation Updates

To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
13.4 Community Resources

The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
13.5 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
13.6 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
LM158, LM158A, LM258, LM258A
13.7 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms and definitions.
14 Mechanical, Packaging, and Orderable Information

The following pages include mechanical packaging and orderable information. This information is the most-
current data available for the designated devices. This data is subject to change without notice and without
revision of this document. For browser based versions of this data sheet, see the left-hand navigation pane.

PACKAGE OPTION ADDENDUM
www.ti.com 27-Sep-2018
PACKAGING INFORMATION
Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) (6) (3) (4/5)
5962-87710012A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-
87710012A
LM158FKB
5962-8771001PA ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 8771001PA
LM158
5962-87710022A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-
87710022A
LM158AFKB
5962-8771002PA ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 8771002PA
LM158A
LM158AFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-
87710022A
LM158AFKB
LM158AJG ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 LM158AJG
LM158AJGB ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 8771002PA
LM158A
LM158FKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-
87710012A
LM158FKB
LM158JG ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 LM158JG
LM158JGB ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 8771001PA
LM158
LM258AD ACTIVE SOIC D 8 75 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -25 to 85 LM258A
& no Sb/Br)
LM258ADGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS CU NIPDAU | Level-1-260C-UNLIM -25 to 85 (M3L, M3P, M3S, M3
& no Sb/Br) CU NIPDAUAG U)
LM258ADR ACTIVE SOIC D 8 2500 Green (RoHS CU NIPDAU | CU SN Level-1-260C-UNLIM -25 to 85 LM258A
& no Sb/Br)
LM258ADRE4 ACTIVE SOIC D 8 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -25 to 85 LM258A
& no Sb/Br)
LM258ADRG4 ACTIVE SOIC D 8 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -25 to 85 LM258A
& no Sb/Br)
LM258AP ACTIVE PDIP P 8 50 Green (RoHS CU NIPDAU | CU SN N / A for Pkg Type -25 to 85 LM258AP
& no Sb/Br)
Addendum-Page 1
(1) Drawing Qty (2) (6) (3) (4/5)
LM258APE4 ACTIVE PDIP P 8 Pb-Free CU NIPDAU N / A for Pkg Type -25 to 85 LM258AP
(RoHS)
LM258D ACTIVE SOIC D 8 75 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -25 to 85 LM258
& no Sb/Br)
LM258DG4 ACTIVE SOIC D 8 75 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -25 to 85 LM258
& no Sb/Br)
LM258DGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS CU NIPDAU | Level-1-260C-UNLIM -25 to 85 (M2L, M2P, M2S, M2
LM258DGKRG4 ACTIVE VSSOP DGK 8 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -25 to 85 (M2L, M2P, M2S, M2
& no Sb/Br) U)
LM258DR ACTIVE SOIC D 8 2500 Green (RoHS CU NIPDAU | CU SN Level-1-260C-UNLIM -25 to 85 LM258
& no Sb/Br)
LM258DRG3 ACTIVE SOIC D 8 2500 Green (RoHS CU SN Level-1-260C-UNLIM -25 to 85 LM258
& no Sb/Br)
LM258DRG4 ACTIVE SOIC D 8 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -25 to 85 LM258
& no Sb/Br)
LM258P ACTIVE PDIP P 8 50 Green (RoHS CU NIPDAU | CU SN N / A for Pkg Type -25 to 85 LM258P
& no Sb/Br)
LM258PE4 ACTIVE PDIP P 8 50 Pb-Free CU NIPDAU N / A for Pkg Type -25 to 85 LM258P
(RoHS)
LM2904AVQDR ACTIVE SOIC D 8 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 L2904AV
& no Sb/Br)
LM2904AVQDRG4 ACTIVE SOIC D 8 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 L2904AV
& no Sb/Br)
LM2904AVQPWR ACTIVE TSSOP PW 8 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 L2904AV
& no Sb/Br)
LM2904AVQPWRG4 ACTIVE TSSOP PW 8 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 L2904AV
& no Sb/Br)
LM2904D ACTIVE SOIC D 8 75 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 LM2904
& no Sb/Br)
LM2904DE4 ACTIVE SOIC D 8 75 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 LM2904
& no Sb/Br)
LM2904DG4 ACTIVE SOIC D 8 75 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 LM2904
& no Sb/Br)
LM2904DGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS CU NIPDAU | Level-1-260C-UNLIM -40 to 125 (MBL, MBP, MBS, MB
Addendum-Page 2
(1) Drawing Qty (2) (6) (3) (4/5)
LM2904DGKRG4 ACTIVE VSSOP DGK 8 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 (MBL, MBP, MBS, MB
& no Sb/Br) U)
LM2904DR ACTIVE SOIC D 8 2500 Green (RoHS CU NIPDAU | CU SN Level-1-260C-UNLIM -40 to 125 LM2904
& no Sb/Br)
LM2904DRE4 ACTIVE SOIC D 8 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 LM2904
& no Sb/Br)
LM2904DRG3 ACTIVE SOIC D 8 2500 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 LM2904
& no Sb/Br)
LM2904DRG4 ACTIVE SOIC D 8 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 LM2904
& no Sb/Br)
LM2904P ACTIVE PDIP P 8 50 Green (RoHS CU NIPDAU | CU SN N / A for Pkg Type -40 to 125 LM2904P
& no Sb/Br)
LM2904PE4 ACTIVE PDIP P 8 TBD Call TI Call TI -40 to 125
LM2904PSR ACTIVE SO PS 8 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 L2904
& no Sb/Br)
LM2904PW ACTIVE TSSOP PW 8 150 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 L2904
& no Sb/Br)
LM2904PWR ACTIVE TSSOP PW 8 2000 Green (RoHS CU NIPDAU | CU SN Level-1-260C-UNLIM -40 to 125 L2904
& no Sb/Br)
LM2904PWRG3 ACTIVE TSSOP PW 8 2000 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 L2904
& no Sb/Br)
LM2904PWRG4-JF ACTIVE TSSOP PW 8 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 L2904
& no Sb/Br)
LM2904QDR ACTIVE SOIC D 8 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 2904Q1
& no Sb/Br)
LM2904QDRG4 ACTIVE SOIC D 8 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 2904Q1
& no Sb/Br)
LM2904VQDR ACTIVE SOIC D 8 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 L2904V
& no Sb/Br)
LM2904VQDRG4 ACTIVE SOIC D 8 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 L2904V
& no Sb/Br)
LM2904VQPWR ACTIVE TSSOP PW 8 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 L2904V
& no Sb/Br)
LM2904VQPWRG4 ACTIVE TSSOP PW 8 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 L2904V
& no Sb/Br)
Addendum-Page 3
(1) Drawing Qty (2) (6) (3) (4/5)
LM358AD ACTIVE SOIC D 8 75 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 LM358A

& no Sb/Br)
LM358ADE4 ACTIVE SOIC D 8 75 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 LM358A
& no Sb/Br)
LM358ADG4 ACTIVE SOIC D 8 75 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 LM358A
& no Sb/Br)
LM358ADGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS CU NIPDAU | Level-1-260C-UNLIM 0 to 70 (M6L, M6P, M6S, M6
LM358ADGKRG4 ACTIVE VSSOP DGK 8 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 (M6L, M6P, M6S, M6
& no Sb/Br) U)
LM358ADR ACTIVE SOIC D 8 2500 Green (RoHS CU NIPDAU | CU SN Level-1-260C-UNLIM 0 to 70 LM358A
& no Sb/Br)
LM358ADRE4 ACTIVE SOIC D 8 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 LM358A
& no Sb/Br)
LM358ADRG4 ACTIVE SOIC D 8 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 LM358A
& no Sb/Br)
LM358AP ACTIVE PDIP P 8 50 Green (RoHS CU NIPDAU | CU SN N / A for Pkg Type 0 to 70 LM358AP
& no Sb/Br)
LM358APE4 ACTIVE PDIP P 8 50 TBD Call TI Call TI 0 to 70 LM358AP
LM358APW ACTIVE TSSOP PW 8 150 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 L358A

& no Sb/Br)
LM358APWR ACTIVE TSSOP PW 8 2000 Green (RoHS CU NIPDAU | CU SN Level-1-260C-UNLIM 0 to 70 L358A
& no Sb/Br)
LM358APWRG4 ACTIVE TSSOP PW 8 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 L358A
& no Sb/Br)
LM358BIDR PREVIEW SOIC D 8 2500 TBD Call TI Call TI -40 to 85
LM358D ACTIVE SOIC D 8 75 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 LM358
& no Sb/Br)
LM358DG4 ACTIVE SOIC D 8 75 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 LM358
& no Sb/Br)
LM358DGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS CU NIPDAU | Level-1-260C-UNLIM 0 to 70 (M5L, M5P, M5S, M5
LM358DGKRG4 ACTIVE VSSOP DGK 8 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 (M5L, M5P, M5S, M5
& no Sb/Br) U)
Addendum-Page 4
(1) Drawing Qty (2) (6) (3) (4/5)
LM358DR ACTIVE SOIC D 8 2500 Green (RoHS CU NIPDAU | CU SN Level-1-260C-UNLIM 0 to 70 LM358

& no Sb/Br)
LM358DRE4 ACTIVE SOIC D 8 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 LM358
& no Sb/Br)
LM358DRG3 ACTIVE SOIC D 8 2500 Green (RoHS CU SN Level-1-260C-UNLIM 0 to 70 LM358
& no Sb/Br)
LM358DRG4 ACTIVE SOIC D 8 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 LM358
& no Sb/Br)
LM358P ACTIVE PDIP P 8 50 Green (RoHS CU NIPDAU | CU SN N / A for Pkg Type 0 to 70 LM358P
& no Sb/Br)
LM358PE3 ACTIVE PDIP P 8 50 Pb-Free CU SN N / A for Pkg Type 0 to 70 LM358P
(RoHS)
LM358PE4 ACTIVE PDIP P 8 50 Green (RoHS CU NIPDAU N / A for Pkg Type 0 to 70 LM358P
& no Sb/Br)
LM358PSR ACTIVE SO PS 8 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 L358
& no Sb/Br)
LM358PW ACTIVE TSSOP PW 8 150 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 L358
& no Sb/Br)
LM358PWR ACTIVE TSSOP PW 8 2000 Green (RoHS CU NIPDAU | CU SN Level-1-260C-UNLIM 0 to 70 L358
& no Sb/Br)
LM358PWRG3 ACTIVE TSSOP PW 8 2000 Green (RoHS CU SN Level-1-260C-UNLIM 0 to 70 L358
& no Sb/Br)
LM358PWRG4 ACTIVE TSSOP PW 8 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 L358
& no Sb/Br)
LM358PWRG4-JF ACTIVE TSSOP PW 8 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 0 to 70 L358
& no Sb/Br)
PLM358BIDR ACTIVE SOIC D 8 2500 TBD Call TI Call TI -40 to 85
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
Addendum-Page 5
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LM258A, LM2904 :
• Automotive: LM2904-Q1
• Enhanced Product: LM258A-EP, LM2904-EP
NOTE: Qualified Version Definitions:
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
• Enhanced Product - Supports Defense, Aerospace and Medical Applications
Addendum-Page 6
PACKAGE MATERIALS INFORMATION
www.ti.com 14-Oct-2018
TAPE AND REEL INFORMATION
*All dimensions are nominal

Device Package Package Pins SPQ Reel Reel A0 B0 K0 P1 W Pin1
Type Drawing Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LM258ADGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LM258ADR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
LM258ADR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
LM258ADR SOIC D 8 2500 330.0 12.8 6.4 5.2 2.1 8.0 12.0 Q1
LM258ADRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
LM258ADRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
LM258DGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LM258DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
LM258DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
LM258DR SOIC D 8 2500 330.0 12.8 6.4 5.2 2.1 8.0 12.0 Q1
LM258DRG3 SOIC D 8 2500 330.0 12.8 6.4 5.2 2.1 8.0 12.0 Q1
LM258DRG3 SOIC D 8 2500 330.0 15.4 6.4 5.2 2.1 8.0 12.0 Q1
LM258DRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
LM258DRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
LM2904AVQDR SOIC D 8 2500 330.0 12.5 6.4 5.2 2.1 8.0 12.0 Q1
LM2904AVQDRG4 SOIC D 8 2500 330.0 12.5 6.4 5.2 2.1 8.0 12.0 Q1
Pack Materials-Page 1

(mm) W1 (mm)
LM2904AVQPWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1
LM2904AVQPWRG4 TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1
LM2904DR SOIC D 8 2500 330.0 12.8 6.4 5.2 2.1 8.0 12.0 Q1
LM2904DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
LM2904DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
LM2904DRG3 SOIC D 8 2500 330.0 12.8 6.4 5.2 2.1 8.0 12.0 Q1
LM2904DRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
LM2904DRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
LM2904PSR SO PS 8 2000 330.0 16.4 8.2 6.6 2.5 12.0 16.0 Q1
LM2904PWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1
LM2904PWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1
LM2904PWRG3 TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1
LM2904PWRG4-JF TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1
LM2904QDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
LM2904VQDR SOIC D 8 2500 330.0 12.5 6.4 5.2 2.1 8.0 12.0 Q1
LM2904VQPWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1
LM2904VQPWRG4 TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1
LM358ADR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
LM358ADR SOIC D 8 2500 330.0 12.8 6.4 5.2 2.1 8.0 12.0 Q1
LM358ADR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
LM358ADRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
LM358ADRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
LM358APWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1
LM358APWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1
LM358APWRG4 TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1
LM358DR SOIC D 8 2500 330.0 12.8 6.4 5.2 2.1 8.0 12.0 Q1
LM358DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
LM358DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
LM358DRG3 SOIC D 8 2500 330.0 12.8 6.4 5.2 2.1 8.0 12.0 Q1
LM358DRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
LM358DRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
LM358PSR SO PS 8 2000 330.0 16.4 8.2 6.6 2.5 12.0 16.0 Q1
LM358PWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1
LM358PWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1
LM358PWRG3 TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1

(mm) W1 (mm)
LM358PWRG4 TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1
LM358PWRG4-JF TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1
*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM258ADGKR VSSOP DGK 8 2500 364.0 364.0 27.0
LM258ADR SOIC D 8 2500 340.5 338.1 20.6
LM258ADR SOIC D 8 2500 367.0 367.0 35.0
LM258ADR SOIC D 8 2500 364.0 364.0 27.0
LM258ADRG4 SOIC D 8 2500 340.5 338.1 20.6
LM258ADRG4 SOIC D 8 2500 367.0 367.0 35.0
LM258DGKR VSSOP DGK 8 2500 364.0 364.0 27.0
LM258DGKR VSSOP DGK 8 2500 332.0 358.0 35.0
LM258DR SOIC D 8 2500 367.0 367.0 35.0
LM258DR SOIC D 8 2500 340.5 338.1 20.6
LM258DR SOIC D 8 2500 364.0 364.0 27.0
LM258DRG3 SOIC D 8 2500 364.0 364.0 27.0
LM258DRG3 SOIC D 8 2500 333.2 345.9 28.6
LM258DRG4 SOIC D 8 2500 340.5 338.1 20.6
LM258DRG4 SOIC D 8 2500 367.0 367.0 35.0
LM2904AVQDR SOIC D 8 2500 340.5 338.1 20.6
LM2904AVQDRG4 SOIC D 8 2500 340.5 338.1 20.6
LM2904AVQPWR TSSOP PW 8 2000 367.0 367.0 35.0
LM2904AVQPWRG4 TSSOP PW 8 2000 367.0 367.0 35.0
LM2904DGKR VSSOP DGK 8 2500 364.0 364.0 27.0
LM2904DGKR VSSOP DGK 8 2500 332.0 358.0 35.0
LM2904DGKR VSSOP DGK 8 2500 358.0 335.0 35.0
LM2904DR SOIC D 8 2500 364.0 364.0 27.0
LM2904DR SOIC D 8 2500 367.0 367.0 35.0
LM2904DR SOIC D 8 2500 340.5 338.1 20.6
LM2904DRG3 SOIC D 8 2500 364.0 364.0 27.0
LM2904DRG4 SOIC D 8 2500 367.0 367.0 35.0
LM2904DRG4 SOIC D 8 2500 340.5 338.1 20.6
LM2904PSR SO PS 8 2000 367.0 367.0 38.0
LM2904PWR TSSOP PW 8 2000 364.0 364.0 27.0
LM2904PWR TSSOP PW 8 2000 367.0 367.0 35.0
LM2904PWRG3 TSSOP PW 8 2000 364.0 364.0 27.0
LM2904PWRG4-JF TSSOP PW 8 2000 367.0 367.0 35.0
LM2904QDR SOIC D 8 2500 367.0 367.0 38.0
LM2904VQDR SOIC D 8 2500 340.5 338.1 20.6
LM2904VQPWR TSSOP PW 8 2000 367.0 367.0 35.0
LM2904VQPWRG4 TSSOP PW 8 2000 367.0 367.0 35.0
LM358ADR SOIC D 8 2500 340.5 338.1 20.6
LM358ADR SOIC D 8 2500 364.0 364.0 27.0
LM358ADR SOIC D 8 2500 367.0 367.0 35.0
LM358ADRG4 SOIC D 8 2500 367.0 367.0 35.0
LM358ADRG4 SOIC D 8 2500 340.5 338.1 20.6
LM358APWR TSSOP PW 8 2000 367.0 367.0 35.0
LM358APWR TSSOP PW 8 2000 364.0 364.0 27.0
LM358APWRG4 TSSOP PW 8 2000 367.0 367.0 35.0
LM358DGKR VSSOP DGK 8 2500 358.0 335.0 35.0
LM358DGKR VSSOP DGK 8 2500 364.0 364.0 27.0
LM358DGKR VSSOP DGK 8 2500 332.0 358.0 35.0
LM358DR SOIC D 8 2500 364.0 364.0 27.0
LM358DR SOIC D 8 2500 367.0 367.0 35.0
LM358DR SOIC D 8 2500 340.5 338.1 20.6
LM358DRG3 SOIC D 8 2500 364.0 364.0 27.0
LM358DRG4 SOIC D 8 2500 340.5 338.1 20.6
LM358DRG4 SOIC D 8 2500 367.0 367.0 35.0
LM358PSR SO PS 8 2000 367.0 367.0 38.0
LM358PWR TSSOP PW 8 2000 364.0 364.0 27.0
LM358PWR TSSOP PW 8 2000 367.0 367.0 35.0
LM358PWRG3 TSSOP PW 8 2000 364.0 364.0 27.0
LM358PWRG4 TSSOP PW 8 2000 367.0 367.0 35.0
LM358PWRG4-JF TSSOP PW 8 2000 367.0 367.0 35.0
MECHANICAL DATA
MCER001A – JANUARY 1995 – REVISED JANUARY 1997
JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE
0.400 (10,16)
0.355 (9,00)
8 5
0.280 (7,11)
0.245 (6,22)
1 4
0.065 (1,65)
0.045 (1,14)
0.063 (1,60) 0.310 (7,87)

0.020 (0,51) MIN
0.015 (0,38) 0.290 (7,37)
0.200 (5,08) MAX

Seating Plane
0.130 (3,30) MIN
0.023 (0,58)
0°–15°
0.015 (0,38)
0.100 (2,54) 0.014 (0,36)
0.008 (0,20)
4040107/C 08/96
NOTES: A. All linear dimensions are in inches (millimeters).

B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification.
E. Falls within MIL STD 1835 GDIP1-T8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

PACKAGE OUTLINE
PW0008A SCALE 2.800
TSSOP - 1.2 mm max height
SMALL OUTLINE PACKAGE
C
6.6 SEATING PLANE
TYP
6.2
A PIN 1 ID 0.1 C
AREA
6X 0.65
8
1
3.1 2X
2.9
NOTE 3 1.95
4
5
0.30
8X
0.19
4.5 1.2 MAX
B 0.1 C A B
4.3
NOTE 4
(0.15) TYP
SEE DETAIL A
0.25
GAGE PLANE
0.75 0.15
0 -8 0.05
0.50
DETAIL A
TYPICAL
4221848/A 02/2015
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm per side.
4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side.
5. Reference JEDEC registration MO-153, variation AA.
www.ti.com
EXAMPLE BOARD LAYOUT
PW0008A TSSOP - 1.2 mm max height
8X (1.5)
8X (0.45) SYMM
(R0.05)
1 TYP
8
SYMM
6X (0.65)
5
4
(5.8)
LAND PATTERN EXAMPLE

SCALE:10X
SOLDER MASK METAL UNDER SOLDER MASK

METAL OPENING
OPENING SOLDER MASK
0.05 MAX 0.05 MIN

ALL AROUND ALL AROUND
NON SOLDER MASK SOLDER MASK

DEFINED DEFINED
SOLDER MASK DETAILS

NOT TO SCALE
4221848/A 02/2015
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.

7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
PW0008A TSSOP - 1.2 mm max height
8X (1.5)
SYMM (R0.05) TYP
8X (0.45)
1
8
SYMM
6X (0.65)
5
4
(5.8)
SOLDER PASTE EXAMPLE

BASED ON 0.125 mm THICK STENCIL
SCALE:10X
4221848/A 02/2015
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated

LM7900

Uploaded by

Copyright:

Available Formats

LM7900

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LM7900

Uploaded by

Copyright:

Available Formats

Product Order Technical Tools & Support &

Folder Now Documents Software Community

LM158, LM158A, LM258, LM258A

Industry-Standard Dual Operational Amplifiers

Single-Pole, Low-Pass Filter LM158, LM158A LCCC (20) 8.89 mm × 8.89 mm

RG RF (1) For all available packages, see the orderable addendum at

Changes from Revision U (January 2017) to Revision V Page

• Changed the data sheet title ................................................................................................................................................. 1

2 Submit Documentation Feedback Copyright © 1976–2018, Texas Instruments Incorporated

Revision History (continued)

Changes from Revision T (April 2015) to Revision U Page

• Changed data sheet title......................................................................................................................................................... 1

Changes from Revision S (January 2014) to Revision T Page

Changes from Revision R (July 2010) to Revision S Page

Copyright © 1976–2018, Texas Instruments Incorporated Submit Documentation Feedback 3

5 Device Comparison Table

4 Submit Documentation Feedback Copyright © 1976–2018, Texas Instruments Incorporated

6 Pin Configuration and Functions

D, DGK, P, PS, PW, and JG Packages

Copyright © 1976–2018, Texas Instruments Incorporated Submit Documentation Feedback 5

7.2 ESD Ratings

6 Submit Documentation Feedback Copyright © 1976–2018, Texas Instruments Incorporated

7.3 Recommended Operating Conditions

7.4 Thermal Information

Copyright © 1976–2018, Texas Instruments Incorporated Submit Documentation Feedback 7

7.5 Electrical Characteristics: LM358B and LM358BA

Common-mode input (V–) (V+) – 1.5

Common-mode rejection (V–) < VCM < (V+) – 1.5 V 80 103

Quiescent current per VS = 5 V; VO = 2.5 V; IO = 0 A 300 460

(1) All typical values are TA = 25°C.

8 Submit Documentation Feedback Copyright © 1976–2018, Texas Instruments Incorporated

7.6 Electrical Characteristics: LM2904B and LM2904BA

Common-mode input voltage (V–) (V+) – 1.5

(1) All typical values are TA = 25°C.

Copyright © 1976–2018, Texas Instruments Incorporated Submit Documentation Feedback 9

7.7 Electrical Characteristics: LM358, LM358A

Quiescent current per VO = 2.5 V; IO = 0 A 350 600

10 Submit Documentation Feedback Copyright © 1976–2018, Texas Instruments Incorporated

7.8 Electrical Characteristics: LM2904, LM2904V

Copyright © 1976–2018, Texas Instruments Incorporated Submit Documentation Feedback 11

7.9 Electrical Characteristics: LM158, LM158A

12 Submit Documentation Feedback Copyright © 1976–2018, Texas Instruments Incorporated

7.10 Electrical Characteristics: LM258, LM258A

Copyright © 1976–2018, Texas Instruments Incorporated Submit Documentation Feedback 13

7.11 Typical Characteristics

Supply Current (mA)

14 Submit Documentation Feedback Copyright © 1976–2018, Texas Instruments Incorporated

Typical Characteristics (continued)

Output Voltage (Vdc) relative to Vcc

Figure 9. Output Sinking Characteristics Figure 10. Source Current Limiting

Copyright © 1976–2018, Texas Instruments Incorporated Submit Documentation Feedback 15

8 Parameter Measurement Information

Figure 11. Unity-Gain Amplifier Figure 12. Noise-Test Circuit

16 Submit Documentation Feedback Copyright © 1976–2018, Texas Instruments Incorporated

9.2 Functional Block Diagram

≈6-µA ≈6-µA ≈100-µA

GND (or VCC−)

Copyright © 1976–2018, Texas Instruments Incorporated Submit Documentation Feedback 17

9.3 Feature Description

9.3.2 Slew Rate