SN74LS245

Octal Bus Transceiver

The SN74LS245 is an Octal Bus Transmitter/Receiver designed for
8-line asynchronous 2-way data communication between data buses.
Direction Input (DR) controls transmission of Data from bus A to bus
B or bus B to bus A depending upon its logic level. The Enable input
(E) can be used to isolate the buses.
http://onsemi.com
• Hysteresis Inputs to Improve Noise Immunity
• 2-Way Asynchronous Data Bus Communication LOW
• Input Diodes Limit High-Speed Termination Effects POWER
• ESD > 3500 Volts
SCHOTTKY
LOGIC AND CONNECTION DIAGRAMS DIP (TOP VIEW)

VCC E B1 B2 B3 B4 B5 B6 B7 B8
20 19 18 17 16 15 14 13 12 11

20

PLASTIC
1 2 3 4 5 6 7 8 9 10 N SUFFIX
CASE 738
DIR A1 A2 A3 A4 A5 A6 A7 A8 GND

TRUTH TABLE
INPUTS
OUTPUT
E DIR 20

L L Bus B Data to Bus A 1

L H Bus A Data to Bus B
H X Isolation SOIC
DW SUFFIX
H = HIGH Voltage Level
L = LOW Voltage Level CASE 751D
X = Immaterial

GUARANTEED OPERATING RANGES

Symbol Parameter Min Typ Max Unit
ORDERING INFORMATION
VCC Supply Voltage 4.75 5.0 5.25 V
Device Package Shipping
TA Operating Ambient 0 25 70 °C
Temperature Range SN74LS245N 16 Pin DIP 1440 Units/Box
IOH Output Current – High – 3.0 mA SN74LS245DW 16 Pin 2500/Tape & Reel
– 15 mA
IOL Output Current – Low 24 mA

 Semiconductor Components Industries, LLC, 1999 1 Publication Order Number:

December, 1999 – Rev. 6 SN74LS245/D
 SN74LS245

DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)

Limits
Symbol Parameter Min Typ Max Unit Test Conditions
Guaranteed Input HIGH Voltage for
VIH Input HIGH Voltage 2.0 V
All Inputs
0.8 Guaranteed Input LOW Voltage for
VIL Input LOW Voltage V
All Inputs
VT+–VT– Hysteresis 0.2 0.4 V VCC = MIN
VIK Input Clamp Diode Voltage – 0.65 – 1.5 V VCC = MIN, IIN = – 18 mA
2.4 3.4 V VCC = MIN, IOH = – 3.0 mA
VOH
O Output HIGH Voltage
2.0 V VCC = MIN, IOH = MAX

0.25 0.4 V IOL = 12 mA VCC = VCC MIN,

VOL
O Output LOW Voltage VIN = VIL or VIH
0.35 0.5 V IOL = 24 mA per Truth Table

IOZH Output Off Current HIGH 20 µA VCC = MAX, VOUT = 2.7 V

IOZL Output Off Current LOW – 200 µA VCC = MAX, VOUT = 0.4 V
A or B, DR or
20 µA VCC = MAX, VIN = 2.7 V
E
IIH I
Input
t HIGH C
Currentt
DR or E 0.1 mA VCC = MAX, VIN = 7.0 V
A or B 0.1 mA VCC = MAX, VIN = 5.5 V
IIL Input LOW Current – 0.2 mA VCC = MAX, VIN = 0.4 V
IOS Output Short Circuit Current (Note 1) – 40 – 225 mA VCC = MAX
Power Supply Current
Total, Output HIGH 70
ICC mA
A VCC = MAX
Total, Output LOW 90
Total at HIGH Z 95
Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (TA = 25°C, VCC = 5.0 V, TRISE / TFALL ≤ 6.0 ns)

Limits
Symbol Parameter Min Typ Max Unit Test Conditions
tPLH 8.0 12
Propagation Delay, Data to Output ns
tPHL 8.0 12
CL = 45 pF,
F,
tPZH Output Enable Time to HIGH Level 25 40 ns RL = 667 Ω
tPZL Output Enable Time to LOW Level 27 40 ns
tPLZ Output Disable Time from LOW Level 15 25 ns CL = 5.0 pF,
tPHZ Output Disable Time from HIGH Level 15 25 ns RL = 667 Ω

http://onsemi.com
2
 SN74LS245

PACKAGE DIMENSIONS

N SUFFIX
PLASTIC PACKAGE
CASE 738–03
ISSUE E

–A–
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
20 11 Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
B 3. DIMENSION L TO CENTER OF LEAD WHEN
1 10 FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD
FLASH.
C L
INCHES MILLIMETERS
DIM MIN MAX MIN MAX
A 1.010 1.070 25.66 27.17
B 0.240 0.260 6.10 6.60
–T– C 0.150 0.180 3.81 4.57
K D 0.015 0.022 0.39 0.55
SEATING
PLANE M E 0.050 BSC 1.27 BSC
F 0.050 0.070 1.27 1.77
E N G 0.100 BSC 2.54 BSC
J 0.008 0.015 0.21 0.38
G F K 0.110 0.140 2.80 3.55
J 20 PL
L 0.300 BSC 7.62 BSC
D 20 PL 0.25 (0.010) M T B M M 0_ 15 _ 0_ 15_
0.25 (0.010) M T A M N 0.020 0.040 0.51 1.01

D SUFFIX
PLASTIC SOIC PACKAGE
CASE 751D–05
ISSUE F

D
A q
NOTES:
1. DIMENSIONS ARE IN MILLIMETERS.
20 11 2. INTERPRET DIMENSIONS AND TOLERANCES
M

PER ASME Y14.5M, 1994.

B

X 45 _

3. DIMENSIONS D AND E DO NOT INCLUDE MOLD

H
M

PROTRUSION.
E
10X

4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.

0.25

5. DIMENSION B DOES NOT INCLUDE DAMBAR

PROTRUSION. ALLOWABLE PROTRUSION SHALL
BE 0.13 TOTAL IN EXCESS OF B DIMENSION AT
1 10 MAXIMUM MATERIAL CONDITION.

MILLIMETERS
DIM MIN MAX
20X B B A 2.35 2.65
A1 0.10 0.25
0.25 M T A S B S B 0.35 0.49
C 0.23 0.32
D 12.65 12.95
E 7.40 7.60
e 1.27 BSC
A H 10.05 10.55
h 0.25 0.75
L

SEATING L 0.50 0.90

PLANE q 0_ 7_
18X e A1 T C

http://onsemi.com
3
 SN74LS245

ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.

PUBLICATION ORDERING INFORMATION

North America Literature Fulfillment: ASIA/PACIFIC: LDC for ON Semiconductor – Asia Support
Literature Distribution Center for ON Semiconductor Phone: 303–675–2121 (Tue–Fri 9:00am to 1:00pm, Hong Kong Time)
P.O. Box 5163, Denver, Colorado 80217 USA Toll Free from Hong Kong 800–4422–3781
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada Email: ONlit–asia@hibbertco.com
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: ONlit@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–8549
N. American Technical Support: 800–282–9855 Toll Free USA/Canada Phone: 81–3–5487–8345
Email: r14153@onsemi.com
EUROPE: LDC for ON Semiconductor – European Support
German Phone: (+1) 303–308–7140 (M–F 2:30pm to 5:00pm Munich Time) Fax Response Line: 303–675–2167
Email: ONlit–german@hibbertco.com 800–344–3810 Toll Free USA/Canada
French Phone: (+1) 303–308–7141 (M–F 2:30pm to 5:00pm Toulouse Time)
Email: ONlit–french@hibbertco.com ON Semiconductor Website: http://onsemi.com
English Phone: (+1) 303–308–7142 (M–F 1:30pm to 5:00pm UK Time)
For additional information, please contact your local
Email: ONlit@hibbertco.com
Sales Representative.

http://onsemi.com SN74LS245/D
4