HHM-Notes 2 PDF

Smartworld.asia Specworld.
in
LECTURE NOTES ON
Hydraulics and Hydraulic Machines
Department of Civil Engineering
smartworlD.asia
Smartzworld.com 1 jntuworldupdates.org
Smartworld.asia Specworld.in
Governors for Turbines

Pendulum or actuator
To Reduce Speed
g
u
n
g
i
i
Rated Speed
To increase
w
T
o
n
e
s
r
r
t
i
Speed
Rated Speed
Lever
To Reduce Speed
fulcrum
From turbine shaft
mechanis
To increase
m
Speed
Distribution
Gear valve
Pump
Oil
Sump Servomotor or relay
cylinder
smartworlD.asia
Oil pressure governor
A Governor is a mechanism to regulate the speed of the shaft of a turbine. The turbine is
coupled to the shaft of the generator, which is generating power/electricity. The power
generated should have uniform rating of current and frequency which in turn depends on
the speed of the shaft of the turbine. Fig shows the oil pressure governor for a turbine.
The main component parts of the governor are:
1. The servomotor or Relay cylinder
2. The distribution valve or control valve
3. Actuator or Pendulum
4. Oil Sump
5. Gear pump which runs by tapping power from the power shaft by belt drive
6. A pipe system communicating with the control valve, servomotor and the sump
When the turbine is subjected to its normal load, it runs at the normal speed N. When the
load on the turbine increases or decreases the speed of the turbine also will accordingly
decrease ot increase.
The oil pressure governor will restore the speed to the normal value. The normal position
of the governor at the normal speed is shown in fig.
As the load on the turbine increases, the speed decreases in turn reducing the speed of the
vertical bar of the governor. The fly balls of the centrifugal governor are brought to a
lower level, thereby bringing the displacement lever downward. This through the fulcrum
lifts the piston of the control valve and thereby opens the valve A and closes the valve B.
Oil is pumped through valve A and into the servomotor, thereby pushing the piston of the
servomotor backwards. This in turn increases the inlet area of the discharge into the
turbine, thereby increasing the speed.
Similarly, with decrease in load on the turbine, the fly balls move farther away from the
vertical shaft of the governor, thereby lifting the displacement lever upwards. This
through the fulcrum lowers the piston of the control valve and thereby opens the valve B
and closes the valve A. Oil is pumped through valve B and into the servomotor, thereby
pushing the piston of the servomotor forwards. This in turn decreases the inlet area of the
discharge into the turbine, thereby decreasing the speed.
In both the cases mentioned above, the process continues until the normal position is
reached.
smartworlD.asia
HYDRAULIC TURBINES
Introduction:
The device which converts h ydraulic energy into mechanical energy or vice versa is
known as Hydraulic Machines . The h ydraulic machines which convert h ydraulic
energy into mechanical energy are known as
Turbines and that convert mechanical energy into h ydraulic energy is known as Pumps .
Fig . shows a general layout of a h ydroelectric plant .
Headrace
hL
Turbine
Penstock
Hg
H
Animation as in the PPT
Tailrace
smartworlD.asia
Head
hL
H
Hg
Tail Race
It consists of the following:

1 . A Dam constructed across a river or a channel to store water. The reservoir is also
known as Headrace.
2 . Pipes of large diameter called Penstocks which carry water under pressure from
storage reservoir to the turbines . These pipes are usuall y made of steel or
reinforced concrete.
3 . Turbines having different t ypes of vanes or buckets or blades mounted on a
wheel called runner.
4 . Tailrace which is a channel carrying water away from the turbine after the water
has worked on the turbines . The water surface in the tailrace is also referred to as
tailrace .
Important Terms:
Gross Head (H g ): It is the vertical difference between headrace and tailrace.
Net Head:(H): Net head or effective head is the actual head available at the inlet of
the to work on the turbine .
H=Hg -hL
Where h L is the total head loss during the transit of water from the headrace to
smartworlD.asia
tailrace which is m ainl y head loss due to friction, and is given b y
2
hf  4 f LV
2gd
Where f is the coefficient of friction of penstock depending on the type of material of
penstock
L is the total length of penstock
V is the mean flow velocit y of water through the p enstock
D is the diameter of penstock and
g is the acceleration due to gravit y
TYPES OF EFFICIENCIES
Depending on the considerations of input and output, the efficiencies
can be classified as
(i) H ydraulic Efficiency
(ii) Mechanical Efficiency Turbine Runner
(iii) Overall efficienc y
(i) H ydraulic Efficiency: ( h ) Shaft
It is the ratio of the power
developed b y the runner of a
turbine to the power supplied at the inlet Inlet of turbine
of a turbine. Since the power supplied is hydraulic, and the probable loss is between
the striking jet and vane it is rightly called hydraulic efficiency.
If R.P. is the Runner Power and W.P. is the Water Power
smartworlD.asia
 R.P. (01)
h  W.P.
7. Mechanical Efficiency: (m)

It is the ratio of the power available at the shaft to the power developed by the
runner of a turbine. This depends on the slips and other mechanical problems that
will create a loss of energy between the runner in the annular area between the
nozzle and spear, the amount of water reduces as the spear is pushed forward and
vice -versa .
and shaft which is purel y mechanical and hence mechanical efficiency.
If S . P . is the Shaft Power

 S.P. (02)
m
R.P.
(iii) Overall Efficiency: ( )

It is the ratio of the power available at the shaft to the power supplied at the inlet of
a turbine . As this covers overall problems of losses in energy, it is known as
overall efficienc y. This depends on both the h ydraulic losses and the slips and
other mechanical problems
that will create a loss of energy between the jet power supplied and the power
generated at the shaft available for coupling of the generator.
  S.P.
W.P.
(03)
From Eqs 1,2 and 3, we have
 = h x m
Classification of Turbines
The h ydraulic turbines can be classified based on t ype of energy at the inlet,
direction of flow through the vanes, head available at the inlet, discharge through
the vanes and specific speed . They can b e arranged as per the following table:
Turbine Type of Direction Specific

Head Discharge
Name Type energy of flow Speed
High
Low
Pelton Head > Tangential
Impulse Kinetic Low <35 Single jet
Wheel 250m to to runner
smartworlD.asia
35 – 60 Multiple jet
1000m
Medium Radial flow Medium
Francis Medium
60 m to 60 to 300
Turbine Mixed Flow
Reaction Kinetic + 150 m
Turbine Pressure High
Kaplan Low High Axial Flow 300 to 1000
Turbine < 30 m
As can be seen from the above table, an y specific t ype can be explained b y
suitable construction of sentences b y selecting the other items in the table along the
row .
PELTON WHEEL OR TURBINE

Pelton wheel, named after an eminent engineer, is an impulse turbine wherein the
flow is tangential to the runner and the available energy at the entrance is completel
y kinetic energy. Further, it is preferred at a very high head and low discharges with
low specific speeds . The pressure available at the inlet and the outlet is
atmospheric .
Animation:
(i) The water jet has to reduce
and increase as the spear is Breaking jet
brought forward and
backward
(ii) The wheel has to rotate as the
jet strikes
smartworlD.asia
The main components of a Pelton turbine are:
(i) Nozzle and flow regulating arrangement:
Water is brought to the h ydroelectric plant site through large penstocks at the end
of which there will be a nozzle, which converts
the pressure energy completel y into Penstock
kinetic energy. This will convert the Nozzle
liquid flow into a high -speed jet,
which strikes the buckets or
vanes mounted on the runner,
Wheel Spear
which in -turn rotates the runner of
the turbine. The amount of water striking the vanes is controlled b y the forward
and backward motion of the spear . As the water is flowing in the annular area
between the annular area between the
nozzle opening and the spear, the flow gets reduced as the spear moves forward
and vice - versa.
(ii) Runner with buckets:
Runner is a circular disk mounted on a shaft on the periphery of
Buckets
Shaft
Runner
which a number of buckets are fixed equall y spaced as shown in Fig . The
buckets are made of cast -iron cast -steel, bronze or stainless steel depending
upon the head at the inlet of the turbine. The water jet strikes the bucket on the
smartworlD.asia
0
splitter of the bucket and gets deflected through ( ) 160 - 170 .
(iii) Casing:
It is made of cast - iron or fabricated steel plates . The main function of the casing
is to prevent splashing of water and to discharge the water into tailrace .
(iv) Breaking jet:

Even after the amount of water striking the buckets is comple tel y stopped, the
runner goes on rotating for a very long time due to inertia. To stop the runner in a
short time, a small nozzle is provided which directs the jet of water on the back of
bucket with which the rotation of the runner is reversed . This jet i s called as
breaking jet .
Vane
Deflection jet
angle of jet

3 D Picture of a jet striking the splitter and getting split in to two parts and deviating.
u2 Vw2

 V2
Vr2 Vf2
smartworlD.asia
u1 Vr1
Deflection angle
V1=Vw1 u
Vf1=0
Velocit y triangles for the jet striking the bucket

From the impulse -momentum theorem, the force with which the jet strikes tthe bucket
along the direction of vane is given b y
F x = rate of change of momentum of the jet along the direction of vane motion
F x = (Mass of water / second) x change in velocit y along the x direction
  aV1 Vw1 Vw2  


  aV1 Vw1 Vw2  
Work done per second b y the jet on the vane is given b y the product of Force exerted on
the vane and the distance moved b y the vane in one second
W . D . /S = F x x u
 aV1 Vw1 Vw2 u
Input to the jet per second = Kinetic energy of the jet per second
1
  aV13 
2
Efficiency of the jet = Output / sec ond  Workdone / sec ond

Input / sec ond Input / sec ond
 aV1Vw1 Vw2 u
 1  aV
3
2 u V V 
2 1
smartworlD.asia
 w1 w2
V12
From inlet velocit y triangle, V w 1 = V 1
Assuming no shock and ignoring frictional losses through the vane, we have V r 1 = V r 2
= (V 1 – u 1 )
In case of Pelton wheel, the inlet and outlet are located at the same radial distance from
the centre of runner and hence u 1 = u 2 = u
From outlet velocit y triangle, we have V w 2 = V r 2 Cos  - u 2
= (V 1 –u )Cos  - u
Fx   aV1V1  V1 u Cos u
Fx   aV1 V1 u 1 Cos
Substituting these values in the above equation for efficiency, we have
  2u V1  V12 u cos u

V1
2u
 2  V1 u  V1 u
cos V1 
2u
 2 V1 u 1 cos 
V1 
The above equation gives the efficiency of the jet striking the vane in case of Pelton
wheel .
To obtain the maximum efficiency for a given jet velocit y and vane angle, from maxima
-minima, we have
d
0 d u
d
 d   22 1 cos uV1 u 
2
du V 0du
1
V 1 -2u = 0
or u  V1
2
i . e . When the bucket speed is maintained at half the velocity of the jet, the efficiency of
a Pelton wheel will be maximum . Substituting we get,
max 
1
2u
2u smartworlD.asia
2 2u u 1 cos 
max  1 cos
2
From the above it can be seen that more the value of cos , more will be the efficiency.
Form maximum efficiency, the value of cos  should be 1 and the value of  should be 0
0 0
. This condition makes the jet to completel y deviate by 180 and this, forces the jet
striking the bucket to strike the successive bucket on the back of it acting like a breaking
0
jet . Hence to avoid this situation, at least a small angle of  =5 should be provided .
Dec -06/Jan07
6 a. i)Sketch the layout of a PELTON wheel turbine showing the details of
nozzle, buckets and wheel when the turbine axis is horizontal(04) ii) Obtain an
expression for maximum - efficiency of an impulse turbine.
(06)
July 06
6 (a) With a neat sketch explain the l ayout of a h ydro -electric plant (06)
(b) With a neat sketch explain the parts of an Impulse turbine. (06)
Jan 06
6 (a) What Is specific speed of turbine and state Its significance. (04)
(b) Draw a neat sketch of a h ydroelectric plant and mention the
function of each component . (08)
Jan 05
6 (a) Classify the turbines based on head, specific speed and h ydraulic
actions . Give examples for each . (06)
smartworlD.asia
(b) What is meant b y Governing of turbines? Explain with a neat sketch
the governing of an impulse turbine (06)
July 04
5 (a) Explain the classification of turbines . (08)
The head at the base of the nozzle of a Pelton wheel is 640 m . The outlet vane angle of
o
the bucket is 15 . The relative velocit y at the outlet is reduced b y 15% due to friction
along the vanes . If the discharge at outlet is without whirl find the ratio of bucket speed
to the jet speed . If the jet diameter is 100 mm while the wheel diameter is 1 . 2 m, find
the spe ed of the turbine in rpm, the force exerted b y the jet on the wheel, the Power
developed and the h ydraulic efficiency. Take C v =0.97.
Solution:
o
H = 640 m; =15 ; V r 1 = 0 . 85 V r 2 ; V w 2 = 0; d = 100 mm; D = 1 . 2 m;
C v = 0 . 97; K u = ?; N = ?; F x = ?; P = ?; h = ?
We know that the absolute velocit y of jet is given b y
V  Cv 2 g H  0.97 2 10 640 109.74 m/s

Vw2=0
 u2

Vr2 V2=Vf2
smartworlD.asia
u1 Vr1
Deflection angle
V1=Vw1 u
Vf1=0
Let the bucket speed be u

Relative velocit y at inlet = V r 1 = V 1 - u = 109 . 74 - u
Relative velocit y at outlet = V r 2 = (1 -0 . 15)V r 1 = 0 . 85(109 . 74 - u )
But V r 2 cos  = u  0 . 85(109 . 74 -u )cos15
Hence u = 49 . 48 m/s
DN
But u  and hence
60
N  60 u  6049.48  787.5 rpm (Ans)

D  1.2
Jet ratio = m = u  49.48  0.45

V 109.74

Weight of water supplied =  Q = 10 1000  0.12 109.742  8.62 kN/s
4
Force exerted = Fx   aV1 Vw1 Vw2 
But V w 1 = V 1 and V w 2 = 0 and hence

F 1000  0.12 109.742  94.58 kN
x
4
Work done/second = F x x u = 94 . 58 x 49 . 48 = 4679 . 82 kN/s

Kinetic Energy/second = 1  aV 3  1 1000  0.12 109.743  5189.85 kN/s
2 1
2 4
H ydraulic Efficiency =   Work done/s  4679.82 100  90.17%

h
Kinetic Energy/s 5189.85
Dec 06 -Jan 07
smartworlD.asia
A PE LTON wheel turbine is having a mean runner diameter of 1 . 0 m and is running at
1000 rpm . The net head is 100 . 0 m . If the side clearance is 20° and discharge is 0 . 1 m
3
/s, find the power available at the nozzle and
h ydraulic efficiency of the turbine . (10)
Solution:
o 3
D = 1 . 0 m; N = 1000 rpm; H = 100 . 0 m;  = 20 ; Q = 0 . 1 m /s; WD/s = ? and h =
?
Assume C v = 0 . 98
We know that the velocit y of the jet is given b y
V  Cv 2 g H  0.98 2 10 1000 43.83 m/s

The absolute velocity of the vane is given b y
 11000
uDN 52.36 m/s
60 60
This situation is impracticable and hence the data has to be modified . Clearl y state the
assumption as follows:
Assume H = 700 m (Because it is assumed that the t yping and seeing error as 100 for
700)
Absolute velocit y of the jet is given b y
V  Cv 2 g H  0.98 2 10 700 115.96 m/s
52.36 Vw2

 V2
Vr2 Vf2
Deflection angle
52.36 Vr1
V1=115.96 u
Vf1=0
smartworlD.asia
Power available at the n ozzle is the given b y work done per second
WD/second =  Q H =  g Q H = 1000x10x0 . 1x700 = 700 kW
H ydraulic Efficiency is given b y
  2 u V u 1 cos 2 52.36

2
115.96 52.36(1  cos 20)  96.07%
h V 21 115.96
1
July 06
A Pelton wheel has a mean bucket speed of 10 m/s with a jet of water flowing at the rate
of 700 lps under a head of 30 m . The buckets deflect the jet through an angle of 160° .
Calculate the power given b y water to the runner and the h ydraulic efficiency of the
turbine . Assume the coefficient of nozzle as 0 . 98 . (08)
Solution:
3 o
u = 10 m/s; Q = 0 . 7 m /s;  = 180 -160 = 20 ; H = 30 m; C v = 0 . 98;
WD/s = ? and h = ?
2
Assume g = 10m/s
V  Cv 2 g H  0.98 2 10 30 24 m/s
10 Vw2

 V2
Vr2 Vf2
Deflection angle
10 Vr1
V1=24 u
Vf1=0
V r 1 = V 1 -u = 24 – 10 = 14 m/s
Assuming no shock and frictional losses we have V r 1 = V r 2 = 14 m/s
V w 2 = V r 2 Cos  - u = 14 x Cos 20 – 10 = 3 . 16 m/s
We know that the Work done b y the jet on the vane is given by WD/s 
aV1 Vw1 Vw2 u   Q u Vw1 Vw2  as Q = aV 1
smartworlD.asia
1000 0.7 10 24 3.16190.12 kN -m/s (Ans)
1  aV 3  1  QV 2  1 1000 0.7 242  201.6 kN -m/s

IP/s = KE/s 
2 1
2 1
2
H ydraulic Efficiency = Output/ Input = 190 . 12/201 . 6 = 94 . 305% It can
also be directly calculated b y the derived equation as
  2 u V u 1 cos2 210 24 101 cos 20 94.29% (Ans)

h V 21 24
1
Jan 06
A Pelton wheel has to develop 13230 kW under a net head of 800 m while running at a
speed of 600 rpm . If the coefficient of Jet C y = 0 . 97, speed
ratio =0 . 46and the ratiooftheJetdiameteris
1 /16 of wheel diameter . Calculate
i) Pitch circle diameter ii) the diameter of jet
iii) the quantit y of water supplied to the wheel
iv) the number of Jets required .

Assume over all efficiency as 85%. (08)
Solution:
P = 13239 kW; H = 800 m; N = 600 rpm; C v = 0 . 97;  = 0 . 46 (Speed ratio) d/D =
1/16; o = 0 . 85; D = ?; d = ?; n = ?;
2 3
Assume g = 10 m/s and  = 1000 kg/m
We know that the overall efficiency is given b y
3
Output P 13239 10
o     0.85
Input  Q H 10 1000 Q  800
3
Hence Q = 1 . 947 m /s (Ans)
Absolute velocit y of jet is given b y
V  Cv 2 g H  0.97 2 10 800 122.696 m/s

Absolute velocit y of vane is given b y
u  2 g H  0.46 210800  58.186 m/s

The absolute velocity of vane is also given b y
u
D N
60 smartworlD.asia
and hence
D  60 u  6058.186 1.85 m (Ans)

N  600
d  1.85 115 . 625 mm (Ans)

16
  3
Discharge per jet = q d 2 V  0.115625 2 122.696 1.288 m /s
4 4
No . of jets = n  Q  1.947  2 (Ans)

q 1.288
July 05
Design a Pelton wheel for a head of 80m . and speed of 300 RPM . The Pelton wheel
develops 110 kW . Take co - eficient of velocit y= 0 . 98, speed ratio= 0 . 48 and overall
efficiency = 80%. (10)
Solution:
H = 80 m; N = 300 rpm; P = 110 kW; C v = 0 . 98, K u =0 . 48; o = 0 . 80
2 3
Assume g = 10 m/s and  = 1000 kg/m
We know that the overall efficiency is given b y
3
Output P 110 10
     0.8
o
Input QH 10 1000 Q 80
3
Hence Q = 0 . 171875 m /s
Absolute velocit y of jet is given b y
V  Cv 2 g H  0.98 2 10 80 39.2 m/s
Absolute velocit y of vane is given b y u 

2 g H  0.48 21080 19.2 m/s
DN
u and hence
60
60 u 6019.2
D  1.22 m (Ans)
N  300
Single jet Pelton turbine is assumed
Q
smartworlD.asia
The diameter of jet is given b y the discharge continuit y equation

0.171875 4 4

d 2 V  d 2 39.2 
Hence d = 74 . 7 mm
The design parameters are
Single jet
Pitch Diameter = 1 . 22 m
Jet diameter = 74 . 7 mm
Jet Ratio = m  D  1.22 16.32

d 0.0747
No . of Buckets = 0 . 5x m + 15 = 24
Jan 05
It is desired to generate 1000 kW of power and survey reveals that 450 m of static head
3
and a minimum flow of 0 . 3 m /s are available. Comment whether the task can be
accomplished b y installing a Pelton wheel run at 1000 rpm and having an overall
efficiency of 80% .
Further, design the Pelton wheel assuming suitable data for coefficient of
velocit y and coefficient of drag. (08)
Solution:
3
P = 1000 kW; H = 450 m; Q = 0 . 3 m /s; N = 1000 rpm; o = 0 . 8
3 2
Assume C v = 0 . 98; K u =0 . 45;  = 1000 kg/m ; g = 10 m/s
3
Output P 1000 10
o    0.74
Input QH 10 1000 0.3 450
For the given conditions of P, Q and H , it is not possible to achieve the desired
efficiency of 80%.
To decide whether the task can be accomplished b y a Pelton turbine compute the
specific sp eed N s
N P
Ns  5 ;
H 4
where N is the speed of runner, P is the power developed in kW and H is the head
available at the inlet .
smartworlD.asia
1000 1000
Ns 5 15.25
<35 450 4
Hence the installation of single jet Pelton wheel is justified . Absolute
velocit y of jet is given b y
V  Cv 2 g H  0.98 2 10 450 92.97 m/s

Absolute velocit y of vane is given b y u 
2 g H  0.48 21080 19.2 m/s
DN
u and hence
60
60 u 6019.2
D  1.22 m (Ans)
N  300
Single jet Pelton turbine is assumed
The diameter of jet is given b y the discharge continuit y equation
 
Q d 2 V  d 2 39.2 
0.171875 4 4
Hence d = 74 . 7 mm
The design parameters are
Single jet
Pitch Diameter = 1 . 22 m
Jet diameter = 74 . 7 mm
Jet Ratio = m  D  1.22 16.32

d 0.0747
No . of Buckets = 0 . 5x m + 15 = 24
July 04
A double jet Pelton wheel develops 895 MKW with an overall efficienc y of 82% under a
head of 60m . The speed ratio = 0 . 46, jet ratio = 12 and the nozzle coefficient = 0 . 97 .
Find the jet diameter, wheel diameter and wheel
speed in RPM . (12)
Solution:
smartworlD.asia
No . of jets = n = 2; P = 895 kW; o = 0 . 82; H = 60 m; K u = 0 . 46; m = 12;
C v = 0 . 97; D = ?; d = ?; N = ?
We know that the absolute velocit y of jet is given b y
V  Cv 2 g H  0.97 2 10 60  33.6 m/s

The absolute velocity of vane is given b y
u  Ku 2 g H  0.46 210 60 15.93 m/s

Overall efficiency is given b y
3 3
  P and hence Q  P  895 10 1.819 m /s
o QH  H 10 103 0.82 60
3
Discharge per jet = q  Q  1.819  0.9095 m /s
n 2
From discharge continuit y equation, discharge per jet is also given b y
d2 d2
q V 33.6  0.9095
4 4
d  0.186 m
D
Further, the jet ratio m 12 
d
Hence D = 2 . 232 m
D N
Also u  and hence N  60 u  6015.93 136 rpm
60  D  2.232
Note: Design a Pelton wheel: Width of bucket = 5 d and depth of bucket is 1 . 2 d
The following data is related to a Pelton wheel:

Head at the base of the nozzle = 80m; Diameter of the jet = 100 mm;
3
Discharge of the nozzle = 0 . 3m /s; Power at the shaft = 206 kW; Power
absorbed in mechanical resistance = 4 . 5 kW . Determine (i) Power lost in
the nozzle and (ii) Power lost due to h ydraulic resistanc e in the runner .
Solution:
2 2 3
H = 80 m; d = 0 . 1m; a = ¼ d = 0.007854 m ; Q = 0.3 m /s; SP = 206 kW; Power
absorbed in mechanical resistance = 4.5 kW.
From discharge continuity equation, we have, Q = a x
smartworlD.asia
V = 0.007854 x V 0.3
V = 38.197 m/s
Power at the base of the nozzle =  g Q H
= 1000 x 10 x 0.3 x 80 = 240 kW Power
3
corresponding to the kinetic energy of the jet = ½  a V
= 218.85 kW
(i) Power at the base of the nozzle = Power of the jet + Power lost in the nozzle
Power lost in the nozzle = 240  218.85 = 21.15 kW (Ans)
(ii) Power at the base of the nozzle = Power at the shaft + Power lost in the
(nozzle + runner + due to mechanical
resistance)
Power lost in the runner = 240 – (206 + 21.15 + 4.5) = 5.35 kW (Ans)
3
The water available for a Pelton wheel is 4 m /s and the total head from reservoir to the
nozzle is 250 m. The turbine has two runners with two jets per runner. All the four jets
have the same diameters. The pipeline is 3000 m long. The efficiency if power
transmission through the pipeline and the nozzle is 91% and efficiency of each runner is
90%. The velocity coefficient of each nozzle is 0.975 and coefficient of friction 4f for the
pipe is 0.0045. Determine:
(i) The power developed by the turbine; (ii) The diameter of the jet and (iii) The diameter
of the pipeline.
Solution:
3
Q = 4 m /s; Hg = 250 m; No. of jets = n = 2 x 2 = 4; Length of pipe = l = 3000 m;
Efficiency of the pipeline and the nozzle = 0.91 and Efficiency of the runner =
h = 0.9; Cv = 0.975; 4f = 0.0045
Efficiency of power transmission through pipelines and nozzle =
 H g  hf  0.91  250  hf

H
g 250
smartworlD.asia
Hence hf = 22.5 m
Net head on the turbine = H = Hg  hf = 227.5 m
Velocity of jet = V1  Cv 2 g H  0.975 2 10 227.5  65.77 m/s

3
(i) Power at inlet of the turbine = WP = Kinetic energy/second = ½  a V
2
WP = ½ x 4 x 65.77 = 8651.39 kW
  Power developed by turbine  Power developed by turbine  0.9
h
WP 8651.39
Hence power developed by turbine = 0.9 x 8651.39 = 7786.25 kW (Ans)
Total discharge 4.0
(ii) Discharge per jet = q   1.0 m3 /s
No. of jets 4
 2
 2
But q  d V1 1.0  d 65.77
4 4
Diameter of jet = d = 0.14 m (Ans)
(iii) If D is the diameter of the pipeline, then the head loss through the pipe is given by =
hf
2 2
4 f LV fLQ
h   5 (From Q=aV)
f 2gD 3D
2
0.0045 3000 4
h  5  22.5
f 3D
Hence D = 0.956 m (Ans)
The three jet Pelton wheel is required to generate 10,000 kW under a net head of 400 m.
o
The blade at outlet is 15 and the reduction in the relative velocity while passing over the
blade is 5%. If the overall efficiency of the wheel is 80%, Cv = 0.98 and the speed ratio =
0.46, then find: (i) the diameter of the jet, (ii) total flow (iii) the force exerted by a jet on
the buckets (iv) The speed of the runner.
Solution:
No of jets = 3; Total Power P = 10,000 kW; Net head H = 400 m; Blade
o
angle =  = 15 ; Vr2 = 0.95 Vr1 ; Overall efficiency = o = 0.8; Cv = 0.98;
Speed ratio = Ku = 0.45; Frequency = f = 50 Hz/s.
smartworlD.asia
3
P 10,000 10
We know that o   0.8 
gQH 1000 10 Q 400
3
Q = 3.125 m /s (Ans)
Discharge through one nozzle = q  Q  3.125 1.042 m3 /s
n 3
3
Velocity of the jet = V1  Cv 2 g H  0.98 2 10 400  87.65 m /s
 2  2
But q  d V1 1.042  d 87.65
4 4
d = 123 mm (Ans)
3
Velocity of the Vane = u  Ku 2 g H  0.46 2 10 400  41.14 m /s
Vr1 = (V1u1)=87.6541.14 = 46.51 m/s

Vr2 = 0.95 Vr1 = 0.95 x 46.51 = 44.18 m/s
Vw1 = V1 = 87.65 m/s
Vw2 = Vr2 cos u2 = 44.18 cos 1541.14 = 1.53 m/s
Force exerted by the jet on the buckets = Fx =  q(Vw1+Vw2)
Fx = 1000 x 1.042 (87.65+1.53) = 92.926 kN (Ans)

D
Jet ratio = m  10 (Assumed) d
D = 1.23 m
DN
u
60
Hence N  60 u  60 41.14 =638.8 rpm (Ans)
D  1.23
smartworlD.asia
Reaction Turbines
Reaction turbines are those turbines which operate under hydraulic pressure energy and
part of kinetic energy. In this case, the water reacts with the vanes as it moves through
the vanes and transfers its pressure energy to the vanes so that the vanes move in turn
rotating the runner on which they are mounted.
The main types of reaction turbines are

8. Radially outward flow reaction turbine: This reaction turbine consist a
cylindrical disc mounted on a shaft and provided with vanes around the perimeter.
At inlet the water flows into the wheel at the centre and then glides through
radially provided fixed guide vanes and then flows over the moving vanes. The
function of the guide vanes is to direct or guide the water into the moving vanes
in the correct direction and also regulate the amount of water striking the vanes.
The water as it flows along the moving vanes will exert a thrust and hence a
torque on the wheel thereby rotating the wheel. The water leaves the moving
vanes at the outer edge. The wheel is enclosed by a water-tight casing. The water
smartworlD.asia
is then taken to draft tube.
9. Radially inward flow reaction turbine: The constitutional details of this turbine
are similar to the outward flow turbine but for the fact that the guide vanes
surround the moving vanes. This is preferred to the outward flow turbine as this
turbine does not develop racing. The centrifugal force on the inward moving body
of water decreases the relative velocity and thus the speed of the turbine can be
controlled easily.
The main component parts of a reaction turbine are:
(1) Casing, (2) Guide vanes (3) Runner with vanes (4) Draft tube
Casing: This is a tube of decreasing cross-sectional area with the axis of the tube
being of geometric shape of volute or a spiral. The water first fills the casing and
then enters the guide vanes from all
sides radially inwards. The decreasing cross-sectional area helps the velocity of
the entering water from all sides being kept equal. The geometric shape helps the
entering water avoiding or preventing the creation of eddies..
Guide vanes: Already mentioned in the above sections.

Runner with vanes: The runner is mounted on a shaft and the blades are fixed on
the runner at equal distances. The vanes are so shaped that the water reacting with
them will pass through them thereby passing their pressure energy to make it
rotate the runner.
Draft tube: This is a divergent tube fixed at the end of the outlet of the turbine
and the other end is submerged under the water level in the tail race. The water
after working on the turbine, transfers the pressure energy there by losing all its
pressure and falling below atmospheric pressure. The draft tube accepts this water
at the upper end and increases its pressure as the water flows through the tube and
increases more than atmospheric pressure before it reaches the tailrace.
smartworlD.asia
(iv) Mixed flow reaction turbine: This is a turbine wherein it is similar to inward flow
reaction turbine except that when it leaves the moving vane, the direction of water
is turned from radial at entry to axial at outlet. The rest of the parts and
functioning is same as that of the inward flow reaction turbines.
(v) Axial flow reaction turbine: This is a reaction turbine in which the water flows
parallel to the axis of rotation. The shaft of the turbine may be either vertical or
horizontal. The lower end of the shaft is made larger to form the boss or the hub.
A number of vanes are fixed to the boss. When the vanes are composite with the
boss the turbine is called propeller turbine. When the vanes are adjustable the
turbine is called a Kaplan turbine.
D1
D2
Shaft
Moving
Guide vanes
Guide
smartworlD.asia
Inward radial flow reaction turbine
smartworlD.asia
smartworlD.asia
Runn
Shaft
Guide vanes
Volute Volute
Moving
Draft Tube
Francis Turbine Cross -
smartworlD.asia
section
Hydraulics and Hy draulic Machines
smartworlD.asia
Guide vane
smartworlD.asia
Derivation of the efficiency of a reaction turbine
R1
R2
G H
Vw 2
F u2
 
V f2
V2
Vr 2
smartworlD.asia
E
Tangen
t
Wheel B
Tangen
t
V f1
V1 Vr 1
 D

C
A u1 Vw 1
Let
R 1 = Radius of wheel at inlet of the v ane
R 2 = Radius of wheel at outlet of the vane
 = Angular speed of the wheel
Tangential speed of the vane at inlet = u 1 = R 1
Tangential speed of the vane at outlet = u 2 =  R 2

The velocit y triangles at inlet and outlet are drawn as shown in Fig .
 and  are the angles between the absolute velocities of jet and vane at inlet and outlet
respectivel y
 and  are vane angles at inlet and outlet respectivel y
The mass of water striking a series of vanes per second =  a V 1
where a is the area of jet or flow a nd V 1 is the velocit y of flow at inlet . The momentum
of water striking a series of vanes per second at inlet is given b y the product of mass of
water striking per second and the component of velocity of flow at inlet
=  a V 1 x V w 1 (V w 1 is the velocit y component of flow at inlet along tangential

direction)
Similarl y momentum of water striking a series of vanes per second at outlet is given b y
=  a V 1 x (V w 2 ) ( V w 2 is the velocit y component of flow at outlet along
smartworlD.asia
tangential direction and  becaus e the velocit y
component is acting in the opposite direction)

Now angular momentum per second at inlet is given b y the product of momentum of
water at inlet and its radial distance =  a V 1 x V w 1 x R 1
And angular momentum per second at inlet is given b y =  a V 1 x V w 2 x
R2
Torque exerted by water on the wheel is given by impulse momentum theorem as the rate
of change of angular momentum
T =  a V 1 x V w 1 x R 1  a V 1 x V w 2 x R 2
T =  a V 1 (V w 1 R 1 + V w 2 R 2 )
Workdone per second on the wheel = Torque x Angular velocity = T x 
WD/s =  a V 1 (Vw1 R 1 + V w2 R 2 ) x 
=  a V 1 ( V w 1 R 1 x  + V w 2 R 2 x )
As u1 = R 1 and u2 = R 2 , we can simplify the above equation as
WD/s =  a V 1 (Vw1 u 1 + V w2 u 2 )
In the above case, always the velocit y of whirl at outlet is given b y both magnitude
and direction as V w 2 = ( Vr 2 Cos   u 2 )
If the discharge is radial at outlet, then V w 2 = 0 and hence the equation reduces to
WD/s =  a u 1 V 1 V w 1
3
KE/s = ½  a V 1
Efficiency of the reaction turbine is given b y
 aV V u V u 
   1
1
w1 1 w2 2
Workdone/second 3
Kinetic Energy/second  2  aV1
2 V u
  w1 1
V u  velocit y of whirl at outlet is to be substituted as along

w2 2
2
V1 with its sign .
Note: The value of the
V w 2 = (Vr 2 Cos   u 2 )
smartworlD.asia
Summary
(i) Speed ratio = u1 where H is the Head on turbine

2gH
V 1
(ii) Flow ratio = where V f 1 is the velocit y of flow at inlet

2gH
(iii) Discharge flowing through the reaction turbine is given b y
Q=D1 B1 Vf1 =D2 B2 Vf2
Where D 1 and D 2 are the diameters of runner at inlet and exit
B 1 and B 2 are the widths of runner at inlet and exit
V f 1 and V f 2 are the Velocit y of flow at inlet and exit
If the thickness ( t ) of the vane is to be considered, then the area through which
flow takes place is given b y (  D 1  nt ) where n is the number of vanes mounted on
the runner.
Discharge flowing through the reactio n turbine is given b y
Q = (  D 1  nt ) B 1 V f 1 = (  D 2  nt ) B 2 V f 2
2
p V
(iv)The head ( H ) on the turbine is given b y H  1
 1
g 2g
Where p 1 is the pressure at inlet .

(v) Work done per second on the runner =  a V 1 ( Vw 1 u 1  Vw 2 u 2 ) =  Q (
Vw 1 u 1  Vw 2 u 2 )
D N
(vi) u  1
1
60
D N
(vii) u2  2
60
Work done per second
(viii) Work done per unit weight =
Weight of water striking per second
=  Q Vw1u1 Vw2 u2   1 V u V u 
Qg g w1 1 w2 2
If the discharge at the exit is radial, then Vw 2 = 0 and hence
Work done per unit weight = 1 V u 

g w1 1
(ix) H ydraulic efficiency = R.P.   Q Vw1u1 Vw2 u2   1 V u V u 

W .P. gQH g H w1 1 w2 2
smartworlD.asia
If the discharge at the exit is radial, then Vw 2 = 0 and hence
H ydraulic efficiency = 1 V u 
g H w1 1
Blade
smartworlD.asia
Velocity
Francis Turbine installation with straight
Dr . M . N . S he sha Pra ka sh , Pro f e sso r, J . N . N . C o lleg e o f E ng i nee ri ng , Sh i mo g a 13

WORKING OF A KAPLAN TURBINE
Kaplan Turbine installation with an Elbow
The reaction turbine developed b y Victor Kaplan (1815 - 1892) is an improved version
of the older propeller turbine . It is particularl y suitable for generating h ydropower in
locations where large quantities of water are available under a relativel y low head .
smartworlD.asia
Consequentl y the specific speed of these turbines is high, viz . , 300 to 1000 . As in the
case of a Francis turbine, the Kaplan turbine is provided with a spiral casing, guide vane
assembl y and a draft tube. The blades of a Kaplan turbine, three to eight in number are
pivoted around the central hub or boss, thus permitting adjustment of their orientation for
changes in load and head . This arrangement is generall y carried out b y the governor
which also moves the guide vane suitabl y. For this reason, while a fixed blade propeller
turbine gives the best performance under the desi gn load conditions, a Kaplan turbine
gives a consistentl y high efficiency over a larger range of heads, discharges and loads .
The facilit y for adjustment of blade angles ensures shock -less flow even under non -
design conditions of operation .
Water entering radiall y from the spiral casing is imparted a substantial whirl
component b y the wicket gates . Subsequentl y, the curvature of the housing makes the
flow become axial to some extent and finall y then relative flow as it enters the runner, is
tangential to th e leading edge of
the blade as shown in Fig 1(c), Energy transfer from fluid to runner
depends essentiall y on the extent to which the blade is capable of
extinguishing the whirl component of fluid . In most Kaplan runners as in
Francis runners, water leaves the wheel axiall y with almost zero whirl or
tangential component . The velocit y triangles shown in Fig 1(c) are at the
inlet and outlet tips of the runner vane at mid radius, i . e. , midway
between boss periphery and runner periphery.
Com parison between Reaction and Im pulse Turbines
SN Reaction turbine Impulse turbine
1 Only a fraction of the available All the available hydraulic energy is
hydraulic energy is converted into converted into kinetic energy by a nozzle
kinetic energy before the fluid and it is the jet so produced which
enters the runner. strikes the runner blades.
2. Both pressure and velocity change as It is the velocity of jet which changes,
the fluid passes through the runner. the pressure throughout remaining
Pressure at inlet is much higher than atmospheric.
at the outlet.
smartworlD.asia
3 The runner must be enclosed within Water-tight casing is not necessary.
a watertight casing (scroll casing). Casing has no hydraulic function to
perform. It only serves to prevent
splashing and guide water to the tail race
4. Water is admitted over the entire Water is admitted only in the form of jets.
circumference of the runner . There may be one or more jets striking
equal number of buckets simultaneously.
5. Water completely fills at the passages The turbine does not run full and air has
between the blades and while flowing a free access to the buckets
between inlet and outlet sections does
work on the blades
6. The turbine is connected to the tail race The turbine is always installed above the
through a draft tube which is a gradually tail race and there is no draft tube used
expanding passage. It may be installed
above or below the tail race
7. The flow regulation is carried out by Flow regulation is done by means of
means of a guide-vane assembly. Other a needle valve fitted into the nozzle.
component parts are scroll casing, stay
ring, runner and the draft tube
KAPLAN TURBINE - SUMMARY

1 . Peripheral velocities at inlet and outlet are same and given b y
 Do N
u1  u2 
60
where D o is the outer diameter of the runner

2 . Flow velocities at inlet and outlet are same. i . e. V f 1 = V f 2 3 .
Area of flow at inlet is same as area of flow at outlet

Q Do2  Db2 
4
where D b is the diameter of the boss .
smartworlD.asia
The external diameter of an inward flow reaction turbine is 0 . 5 m . The width of the
wheel at inlet is 150 mm and the velocit y of flow at inlet is 1 . 5 m/s . Find the rate of
flow passing through the turbine.
Solution:
D 1 = 0 . 5 m, B 1 = 0 . 15 m, V f 1 = 1 . 5 m/s, Q = ?
Discharge through the turbine = Q =  D 1 B 1 V f 1 =  x 0 . 5 x 0 . 15 x 1 . 5
3
Q = 0 . 353 m /s (Ans)
The external and internal diameters of an inward flow reaction turbine are 600 mm and
200 mm respectivel y and the breadth at inlet is 150 mm . If the velocit y of flow through
3
the runner is constant at 1 . 35 m /s, find the discharge through turbine and the width of
wheel at outlet .
Solution:
D 1 = 0 . 6 m, D 2 = 0 . 2 m, B 1 = 0 . 15 m, V f 1 = V f 2 = 1 . 35 m/s, Q = ?, B 2 = ?
Discharge through the turbine = Q =  D 1 B 1 V f 1 =  x 0 . 6 x 0 . 15 x 1 . 35
3
Q = 0 . 382 m /s (Ans)
Also discharge is given b y Q =  D 2 B 2 V f 2 =  x 0 . 2 x B 2 x 1 . 35  0 . 382
smartworlD.asia
B 2 = 0 . 45 m/s (Ans)
An inward flow reaction turbine running at 500 rpm has an external diameter is 700 mm
and a width of 180 mm . If the gu ide vanes are at 20º to the wheel tangent and the
absolute velocit y of water at inlet is 25 m/s, find (a) discharge through the turbine (b)
inlet vane angle.
Solution:
N = 500 rpm, D 1 = 0 . 7 m, B 1 = 0 . 18 m, a = 20º, V 1 = 25 m/s, Q = ?,  = ? We
know that the peripheral velocit y is given b y
 D N  0.7500
u 1
 18.33 m / s
1
60 60
From inlet velocit y triangle, we have
V f 1 = V 1 Sin x Sin 20 = 8 . 55 m/s
Vw 1 = V 1 Cos  = x Cos 20 = 23 . 49 m/s

Vw1
 u1

Vr1 Vf1
V1
V
Tan  
f1 8.55 1.657

V
u1 23.49 18.33
w1
 = 58 . 89º (Ans)
smartworlD.asia
Q =  D 1 B 1 V f 1 =  x 0 . 7 x 0 . 18 x 8 . 55 = 3 . 384 m /s (Ans)
3
A reaction turbine works at 450 rpm under a head of 120 m . Its diameter at inlet is 1 . 2
2
m and the flow area is 0 . 4 m . The angle made b y the absolute and relative velocities
at inlet are 20º and 60º respectivel y with the tangential velocit y. Determine (i) the
discharge through the turbine (ii) power developed (iii) efficiency. Assume radi al
discharge at outlet .
Solution:
2
N = 450 rpm, H = 120 m, D 1 = 1 . 2 m, a 1 = 0 . 4 m ,  = 20º and  = 60º
Q = ?,  = ?, Vw 2 = 0
We know that the peripheral velocit y is given b y
 D N  1.2450
u 1
  28.27 m / s
1
60 60
V
f1
Tan   V u
w1 1
V
Tan 60  f1
V
 28.27
w1
Hence V f 1 = ( V w 1 – 28 . 27) Tan 60 (01)

V
f1
Further Tan    Tan 20
V
w1
Hence V f 1 = ( V w 1 ) Tan 20 (02)

From equations 1 and 2, we get
(V w 1 – 28 . 27) Tan 60 = V w 1 Tan 20
Hence V w 1 = 35 . 79 m/s
V f 1 = 35 . 79 x Tan 20 = 13 . 03 m/s
3
Discharge Q =  D 1 B 1 V f 1 = a 1 V f 1 = 0 . 4 x 13 . 03 = 5 . 212 m /s (Ans)
Work done per unit weight of water =
1 V u  1 35.7928.27101.178 kN m / N
smartworlD.asia g w1 1 10
Water Power or input per unit weight = H = 120 kN -m/N
  101.178 
H ydraulic efficiency = 84.31% 120
The peripheral velocit y at inlet of an outward flow reaction turbine is 12 m/s . The
internal diameter is 0 . 8 times the external diameter. The vanes are radial at entran ce
and the vane angle at outlet is 20º . The velocit y of flow through the runner at inlet is 4
m/s . If the final discharge is radial and the turbine is situated 1 m below tail water level,
determine:
1 . The guide blade angle
2 . The absolute velocity of water leaving the guides 3 . The
head on the turbine
4 . The h ydraulic efficiency
Solution:
u 1 = 12 m/s, D 1 = 0 . 8 D 2 ,  = 90º,  = 20 º, V f 1 = 4 m/s, Vw 2 = 0, Pressure head at
outlet = 1m,  = ?, V 1 = ?, H = ?, h = ?
 u2
V2=Vf 2
Vr2
V1
Vr1= Vf1
 u1
V
f1 4 , Hence  = 18 . 44 º
From inlet velocit y triangle, Tan   
u1 12
Absolute velocit y of water leaving guide vanes is
u
D N
1
smartworlD.asia
and u 
D N
2
V  u 2 V 2  12 2  42 12.65 m/s
1 1 f1
1
60 2
60
Comparing the above 2 equations, we have 60 u1  60 u2 and hence u1  u2

D D D D
1 2 1 2
Hence u  D2 u  12 15 m/s

2 D1 1 0.8
From outlet velocit y triangle, V 2 = V f 2 = u 2 tan 20 = 15 tan 20 = 5 . 46 m/s As Vw 2
=0
Work done per unit weight of water = Vw1u1  12 12 14.4 kN  m/N
g 10
Head on turbine H
Energy Head at outlet = WD per unit weight + losses
 V2  Vw u 1 
H 1  2
  1
 and hence
   
 2g  g 
 5.462 
10.  1  14.4 16.89 m
2g

H ydraulic efficiency =  Vw1u1 12 12 100 85.26 %
 
h
g H 10 16.89
Jan/Feb 2006
An inward flow water turbine has blades the inner and outer radii of which are 300 mm
and 50 mm respectively. Water enters the blades at the outer periphery with a velocit y of
45 m/s making an angle of 25º with the tangent to the wheel at the inlet tip . Water leaves
the blade with a flow velocit y of 8 m/s . If the blade angles at inlet and outlet are 35º and
25º respectivel y, determine
(i) Speed of the turbine wheel

(ii) Work done per N of water (08)
Solution:
smartworlD.asia
D 1 = 0 . 6 m; D 2 = 0 . 1 m, V 1 = 45 m/s, 25º, V 2 = 8 m/s, 35º, 25º,
N = ?, WD/N = ?
V
f1
Sin   Sin25  0.423
V1
Hence V f 1 = 0 . 423 x 45 = 19 . 035 m/s
V
f1
Tan   tan 25  0.466
V
w1
Hence Vw 1 = 40 . 848 m/s

V
f1 10.035
Tan   tan 35  0.7 
V u
w1 1 40.848 u1
u 1 = 13 . 655 m/s
D N
u1  1 and hence N  60 u1  6013.655 434.65 RPM (Ans)
60  D1  0.6
G H
Vw2
F u2
 
Vf2
Vr2 V2
E
Tangent
Tangent
Vf1
V1 Vr1
smartworlD.asia
 D

C
A u1 Vw1
u D
2  2 N   0.1869.3  4.552 m/s
60 60
V
f1 19.035
Ignoring shock losses, V r 2 =Vr1 =   33.187 m/s
sin  sin 35
Vw 2 = V r 2 cos  - u 2 = 33 . 187 cos 25 – 4 . 552 = 25 . 526 m/s
Work done per unit weight of water = 1 V u V u 

g w1 1 w2 2
1
WD / N  40.848 13.655  25.526 4.552 67.4 m/s (Ans) g
July/Aug 2005
A reaction turbine 0 . 5 m dia develops 200 kW while running at 650 rpm and requires a
3
discharge of 2700 m /hour; The pressure head at entrance to the turbine is 28 m, the
elevation of the turbine casing above the tail
water level is 1 . 8 m and the water enters the turbine with a velocit y of 3 . 5 m/s .
Calculate (a) The effective head and efficiency, (b) The speed, discharge and power if the
same machine is made to operate under a head of 65 m
Solution:
2 3
D = 0 . 5 m, P = 200 kW, N = 650 rpm, Q = 2700/60 = 0 . 75 m /s,
p
1
V 1 = 3 . 5 m/s,  28 m
g
The effective head = H =Head at entry to runner –Kinetic energy in tail race + elevation
of turbine above tailrace
2 2
H  p1  V2  28  3.5 1.8  29.1875 m (Ans)
g 2g 210
3
P 200 10
H ydraulic efficiency =    100  91.36 %
0  g Q H 1000 10 0.75  29.1875
Further unit quantities are given b y
Unit speed = smartworlD.asia

Nu 
N1
H1

N2
H2
Q1 Q2
Unit Discharge = Qu  
H1 H2
Unit Power = P  P1  P2
u 3 3
H 2 H 2
1 2
650  N 2
Nu  120.31
29.1875 65
N 2 = 969 . 97 rpm (Ans)
Q  0.75  Q2  0.1388
u
29.1875 65
3
Q 2 = 1 . 119 m /s (Ans)
P 
u
200
3
 P2 1.268
3
2 2
29.1875 65
P 2 = 664 . 49 kW (Ans)
July/Aug 2005
A Francis turbine has inlet wheel diameter of 2 m and outlet diameter of 1 . 2 m . The
runner runs at 250 rpm and water flows at 8 cumecs . The blades have a constant width of
200 mm . If the vanes are radial at inlet and the discharge is radiall y outwards at exit,
make calculations for the angle of guide vane at inlet and blade angle at outlet (10)
Solution:
3
D 1 = 2 m, D 2 = 1 . 2 m, N = 250 rpm, Q = 8 m /s, b = 0 . 2 m, Vw 1 = u 1 ,
Vw 2 = 0,  = ?,  = ?
u2

V2= Vf 2
Vr2
smartworlD.asia
V1
Vr1= Vf 1

u1= Vw 1
 D N  2 250
u  1   26.18 m/s
1
60 60
D N
u2  2
  1.2 250 15.71m/s
60 60
Q=D1bVf1 =D2bVf2
8=x2x0.2xVf1
Hence V f 1 = 6 . 366 m/s
Similarl y 8 =  x 1 . 2 x 0 . 2 x V f 2
V f 2 = 10 . 61 m/s
  V f 1  6.366
tan
u1 26.18
 = 13 . 67º(Ans) 
V
tan   f2  10.61 
u2 15.71
 = 34 . 03º (Ans)
Determine the overall and h ydraulic efficiencies of an inward flow reaction turbine using
the following data. Output Power = 2500 kW, effective head = 45 m, diameter of runner
= 1 . 5 m, width of runner = 200 mm, guide vane angle = 20 , runner vane angle at inlet
= 60  and specific speed = 100 .
Solution:
P = 2500 kW, H = 45 m, D 1 = 1 . 5 m, b 1 = 0 . 2 m,  = 20 ,  = 60 ,
N s = 110, o = ? , h = ?
smartworlD.asia Vw1
u1
Vr1  Vf1
V1
Vr2
Vf2=V2

u2
We know that specific speed is given b y
5
N P N H 4 100 45 5 4
N s  5
and hence N  s   233 rpm
4
H P 2500
D
u  N   1.5233 18.3 m / s
1
1
60 60
But from inlet velocity triangle, we have
V V
u  f1
 f1
1
tan  tan
V V
18.3  f1
 f1
and hence V f 1 = 8 . 43 m/s
tan 20 tan 60
V
V 8.43
f1
w1  tan   tan 20  23.16 m/s
V w 2 = 0 and hence

h  Vw1u1  23.16 18.3 100  94.18 % (Ans)
gH 10 45
3
Q =  D 1 b 1 V f 1 =  x 1 . 5 x 0 . 2 x 8 . 43 = 7 . 945 m /s
smartworlD.asia
3
P 2500 10
   100  69.93 % (Ans)
o
gQH 1000 10 7.945 45
Determine the output Power, speed, specific speed and vane angle at exit of a Francis
runner using the following data . Head = 75 m, H ydraulic efficiency = 92%, overall
efficiency = 86 %, runner diameters = 1 m and 0 . 5 m, width = 150 mm and guide blade
angle = 18 . Assume that the runner vanes are set normal to the periphery at inlet .
Solution:
Data: H = 75 m, h = 0 . 92, o = 0 . 86, D 1 = 1 m, D 2 = 0 . 5 m,  = 18 ,
Vw 1 = u 1 , P = ?, N = ?, = ?
Vw u u2
h  1 1
 1
gH gH
2
u1 = 0.92 x 10 x 75 =
690 u1 = 26.27 m/s
 D N  1.0N
u 1   26.27 m / s
u1=Vw1
1
60 60

N = 501 . 7 RPM Vr1=Vf1
V1
Vf1 = u1 tan 26.27 x tan 18 = 8.54 m/s
Q=D1 b1 Vf1 =
3
=  x 1 . 0 x 0 . 15 x 8 . 54 = 4 . 02 m /s
u1 u2 and hence u
 2 = 0 . 5 x u 1 = 13 . 135 m/s
D1 D2 V2=Vf2
Assuming V f 1 = V f 2 Vr2
From outlet velocit y triangle, we have 
V u2
 8.54  0.65
f2
tan 
u2 13.135
Hence  = 33 
o P  P  0.86
 g Q H 1000 10 4.02 75
Hence P = 2592 . 9 kW (Ans)
Specific speed =
smartworlD.asia
N s  N 5P  501.7 2592.9 115.75 RPM
H4
75
5
The following data is given for a Francis turbine . Net Head = 60 m; speed N = 700 rpm;
Shaft power = 294 . 3 kW; o = 84%; h = 93%; flow ratio = 0 . 2; breadth ratio n = 0 .
1; Outer diameter of the runner = 2 x inner diameter of the runner . The thickness of the
vanes occupies 5% circumferential area of the runner, velocity of flow is constant at inlet
and outlet and discharge is radial at outlet . Determine:
(i) Guide blade angle

(ii) Runner vane angles at inlet and outlet
(iii) Diameters of runner at inlet and outlet
(iv) Width of wheel at inlet
Solution
H = 60 m; N = 700 rpm; P = 294 . 3 kW; o = 84%; h = 93%;
V
f1 Vw1
flow ratio =  0.2
2gH u1 
Vr1 Vf1
V f 1  0.2 210 60  6.928 m/s V1
Breadth ratio B1  0.1

D1
D1=2xD2
V f 1 = V f 2 = 6 . 928 m/s
Thickness of vanes =
5% of circumferential area of runner
Vr2
Actual area of flow = 0 . 95 π D1 B 1 Vf2=V2
Discharge at outlet = Radial and hence 
V w 2 = 0 and V f 2 = V 2 u2
We know that the overall efficiency is
given b y
smartworlD.asia
3
P 294.310
0  ;0.84 
gQH 1000 10 Q60
3
Q = 0 . 584 m /s
Q = 0 . 95 π D1 B 1 V f 1 = 0 . 95 π D 1 x (0 . 1 D 1 ) x 6 . 928 = 0 . 584
Hence D 1 = 0 . 531 m (Ans)
B1  0.1 and B = 53 . 1 mm (Ans)
D 1
1
D
u  1 N  0.531700 19.46 m/s
1
60 60
V u
H ydraulic efficiency   ;0.93  Vw1 19.46
w1 1
h
gH 1060
V w 1 = 28 . 67 m/s
V
f
From Inlet velocit y triangle tan 

1  6.928  0.242
V
w
1 28.67
Hence Guide blade angle = α = 13 . 58˚ (Ans)
V
tan 
f1 6.928  0.752

V
u1 28.67 19.46
w1
Vane angle at inlet =  = 37 ˚ (Ans)
u2 
 D2 N

 0.5312 700  9.73 m/s
60 60
From outlet velocit y triangle, we have
t
 6.928 
a
0.712 n
9.73 

V
f2
u2
 = 35 . 45 ˚(Ans)
Diameters at inlet and outlet are D 1 = 0 . 531m and D 2 = 0 . 2655 m
smartworlD.asia
A Kaplan turbine develops 9000 kW under a net head of 7 . 5 m . Overall efficiency of
the wheel is 86% The speed ratio based on outer diameter is 2 . 2 and the flow ratio is 0 .
66 . Diameter of the boss is 0 . 35 times the external diameter of the wheel . Determine
the diameter of the runner and the specific speed of the runner.
 2.2 Solution:
P = 9000 kW; H = 7 . 5 m; o = 0 . 86; Speed ratio = 2 . 2; flow ratio = 0 .
66;
D b = 0 . 35 D o ;
u1
2gH
u1  2.2 210 7.5  26.94 m/s

Vf1
 0.66
2gH
V f  0.66 210 7.5 8.08 m/s

1
3
P 9000 10
0  ;0.86 
gQH 1000 10 Q7.5
3
Q = 139 . 5 m /s
smartworlD.asia
 
Q Do2  Db2 V f 1  Do2 0.35Do 2 8.08 139.5
4 4
D o = 5 . 005 m (Ans)
 D N  5.005 N
u o   26.94 m/s
60 60
N =102 . 8 rpm (Ans)
Ns N P  102.8 9000  785.76 rpm (Ans)

5 5
4 4
H 7.5
A Kaplan turbine working under a head of 25 m develops 16,000 kW shaft power. The
outer diameter of the runner is 4 m and hub diameter is 2 m . The guide blade angle is 35˚
. The hydraulic and overall efficiency are
90% and 85% respectivel y. If the velocit y of whirl is zero at outlet, determine runner
vane angles at inlet and outlet and speed of turbine .
Solution
H = 25 m; P = 16,000 kW; D b = 2 m; D o = 4 m;  = 35˚; h = 0 . 9;
0 P
smartworlD.asia
o = 0 . 85; V w 2 = 0;  = ?;  = ?; N = ?
; 0.85 
16000 10
3
gQH 1000 10 Q25

3
Q = 75 . 29 m /s
 
Q Do2  Db2 V f 1  42 22 V f 1  75.29
4 4
V f 1 = 7 . 99 m/s
From inlet velocit y triangle,
Vf1
tan 
V
w1
7.99
Vw1  11.41m/s
tan 35
From H ydraulic efficiency
V u
h  w1 1
gH
11.41u1
0.9 
1025
u 1 = 19 . 72 m/s
V
f1 7.99  0.9614
tan  
u1 Vw1 19.72 11.41
 = 43 . 88 ˚ (Ans)
For Kaplan turbine, u 1 = u 2 = 19 . 72 m/s and V f 1 = V f 2 = 7 . 99 m/s
From outlet velocit y triangle

V
tan   7.99  0.4052
f2
u2 19.72
 = 22 . 06 ˚ (Ans)
 Do N  4 N
u1  u2   19.72
m/s 60 60
N = 94 . 16 rpm (Ans)
 smartworlD.asia u2
V2=Vr2
Vr2
V1
Vr1
Vf1
 
Vw1
1
A Kaplan turbine works under a head of 22 m and runs at 150 rpm . The diameters of the
runner and the boss are 4 . 5 m and 12 m respectivel y. The flow ratio is 0 . 43 . The inlet
vane angle at the extreme edge of the runner is 163˚19′. If the turbine discharges radially
at outlet, determine the discharge, the h ydraulic efficiency, the guide blade angle at the
extreme edge of the runner and the outlet vane angle at the extreme edge of the manner.
Solution:
H = 22 m; N = 150 rpm; D o = 4 . 5 m; D b = 2 m; 163˚19′ V  
V
f1
 0.43
2g H
V V f 2 = V f 1 ; Q = ?; h = ?;  ,
u2

V2=Vr2
smartworlD.asia
Vr2
V1
Vr1
Vf1
 
Vw1
1
 D N  4.5 150
u1  u2  o   35.34 m/s
60 60
V f 1  0.43 21022  9.02 m/s

V
tan180  
f1
u1 Vw1 
9.02
tan180 16319'  0.2997
35.34 Vw1 
V w 1 = 5 . 24 m/s
H ydraulic efficiency is given b y
V u
h   5.24 35.34  84.17%
w1 1
gH 10 22
V
f1 9.02
tan    1.72
V
5.24
w1
 = 59 . 85˚ (Ans)
Vf2 9.02
tan     0.2552
u2 35.34
 = 14 . 32 ˚ (Ans)
smartworlD.asia
A kaplan turbine is to be designed to develop 7,350 kW . The net available head is 5 . 5
m . Assume that the speed ratio as 0 . 68 and the overall

rd
efficiency as 60%. The diameter of the boss is ⅓ of the diameter of the runner. Find
the diameter of the runner, its speed and its specific speed .
Solution:
P = 7350 kW, H = 5 . 5 m
V
f1
 0.68 V f 1  0.68 210 5.5  7.13 m/s
2gH and hence
u
1
 2.09 u  2.2 210 5.5  23.07 m/s
1
2gH and hence

3
P 7350 10
0  ; 0.6 
gQH 1000 10 Q 5.5
3
Q = 222 . 72 m /s

Do2  Db2 V f 1   D 2
D 2 
Q 
o    7.13  222.72
o
4 4  3 
D o = 6 . 69 m (Ans)
 D N  6.69 N
u o   23.07 m/s
60 60
N =65 . 86 rpm (Ans)
Ns  N P  65.86 7350  670.37 rpm (Ans)

5 5
4 4
H 5.5
smartworlD.asia
MOMENTUM EQUATION FOR FLUIDS
Session – II
Net force experienced by fluid along x-direction.
F  m V  U 
x
t x x
  Fx  mVx  U x  
 Fy  mVy  U y  
Where m is the mass flow

rate m = Q
V = Final velocity of fluid along the direction.
U = Initial velocity of fluid along the direction.
 Capability of Momentum and Energy Equations 
Momentum Equation Energy Equation
Applicable
smartworlD.asia
To any fluid flow
To steady flow where energy
changes are zero or known
Velocity and pressure at one

Velocity distribution at one end of
point on the stream line with
control volume.
Information independent knowledge of
required Total forces on the boundaries of energy changes
control distribution at the other
Pressure variation or velocity
end.
variation along stream line
Solution Average final velocity of stream Velocity variation or pressure

gives or total force variation along stream lime
Solution
Actual velocity distribution or
will not Tangential forces due to friction
pressure distribution
give
When energy changes are known

When energy changes are
and detailed information of flow
Best unknown and only overall, is required.
application knowledge of flow is required.
Eg: Velocity and
Eg: Total force, Mean velocity
Pressure distribution.
 Force Exerted by Jet on Plates 

Case-I
To compute the impact of field jet on stationary flat plate held normal to the
jet.
V
y
V x
V
V – Velocity of jet striking the plate
smartworlD.asia
a – Area of cross section of jet.
 m = aV
Force exerted by plate on fluid jet along x –

direction = F x = m [Vx - Ux]
Force exerted by the jet on the plate along x – direction will be equal and
opposite to that of force exerted by plate on the jet.
 Force exerted by jet on plate along x – direction = Fx = m (Ux -

Vx) Fx = av [V - 0]
2
Fx = av
Work done by the jet = Force x Velocity of plate

(ii) Force x 0
(iii) 0
Case-II
To compute the impact of jet on a stationary flat plate held inclined to the
direction of jet.
NORMAL TO PLATE
V
y
V x
(90 )

Force exerted by jet on vane along normal direction.
(iii) Fn = m [Un – Vn]
smartworlD.asia
Fn = aV [(Vsin) – O]
2
Fn = aV sin]
Fy
Fn
(90 - )
Fx
Fx = Fn cos (90 - )
2
Fx = [aV sin] sin
2 2
Fx = aV sin 
Fy = Fn sin (90 - )
2
Fy = [aV sin] cos
2
Fy = aV sin cos
Work done by the jet on vane

(v) Force x Velocity of vane
(vi) Force x 0
(vii) 0
Case-III
To compute the impact of jet on a moving flat plate held normal to the jet.
y (V – U)
x
V U
(V – U)
smartworlD.asia
V = Velocity of jet striking the plate
U = Velocity of vane along the direction of vane.
Adopting the concept of relative velocity, the system can be considered to be

a stationary plate, the jet striking the vane with a relative velocity (V – U).
 m = Q 

a(V - U)
2
Fx = a(V - U)
Work done by the jet on plate = Force x Velocity of

2
plate = a (V - U) x U
Case-IV
To compute the impact of jet on a moving flat plate held inclined to the
direction of jet.
V U
 (V - U)
V = Velocity of jet
U = Velocity of plate along the direction of jet.
Adopting the concept of relative velocity, the above case can be considered
to be fixed vane with a jet velocity of (V – U).
smartworlD.asia
Fn = a (V – U)
2
2
Fx = a (V - U) sin 
2
2
Fy = a (V - U) sin cos
Work done by the jet on vane plate along x – direction

= Fx x Velocity of plate along x – direction
2 2
= a (V - U) sin  U
Case-V
To compute the impact of jet on a stationery symmetrical curved plate, the jet
striking the plate at its centre.
x


V
m = aV
smartworlD.asia
= Fx = m [Ux – Vx]
Fx = (aV) [V – (–Vcos)]
2
Fx = aV (1 + cos]
Work done by the jet on plate is zero since the plate is stationery.
Case-VI
To compute the impact of jet on a moving symmetrical curved plate, the jet
x

U
V
Adopting relative velocity concept, the system can be considered to be a jet

of relative velocity (V – U) striking a fixed plate.
smartworlD.asia
(V – U)


(V – U)
m = a (V – U)
Fx = m [Ux – Vx]
Fx = a (V – U) [(V – U) – (–V – U) cos]
2
Fx = a (V – U) (1 + cos]
7
Work done by the jet on plate = Force x Velocity of date

= Fx U
2
= a(V – U) (1 + cos] U
Case-VII
striking the plate at one of the tips tangentially.
x


smartworlD.asia
V
m = aV
Fx = m [Ux – Vx]
Fx = aV [Vcos – (–Vcos)]
2
Fx = aV (1 + cos]
Fy = m [Uy – Vy]
Fx = aV [Vsin – Vsin]
Fx = 0
MOMENTUM EQUATION FOR FLUIDS

Session – II
Net force experienced by fluid along x-direction.
F  m V  U 
x
t x x
  Fx  mVx  U x  
 Fy  mVy  U y  
Where m is the mass flow

rate m = Q
V = Final velocity of fluid along the direction.
U = Initial velocity of fluid along the direction.
 Capability of Momentum and Energy Equations 
Applicable
smartworlD.asia
Momentum Equation
To any fluid flow

Energy Equation
To steady flow where energy

changes are zero or known
Velocity and pressure at one

Velocity distribution at one end of
point on the stream line with
control volume.
Information independent knowledge of
required Total forces on the boundaries of energy changes
control distribution at the other
Pressure variation or velocity
end.
variation along stream line
Solution Average final velocity of stream Velocity variation or pressure

gives or total force variation along stream lime
Solution
Actual velocity distribution or
will not Tangential forces due to friction
pressure distribution
give
When energy changes are known

When energy changes are
and detailed information of flow
Best unknown and only overall, is required.
application knowledge of flow is required.
Eg: Velocity and
Eg: Total force, Mean velocity
Pressure distribution.
 Force Exerted by Jet on Plates 

Case-I
To compute the impact of field jet on stationary flat plate held normal to the
jet.
V
y
V x
V
V – Velocity of jet striking the plate
smartworlD.asia
a – Area of cross section of jet.
 m = aV
Force exerted by plate on fluid jet along x –

direction = F x = m [Vx - Ux]
Force exerted by the jet on the plate along x – direction will be equal and
opposite to that of force exerted by plate on the jet.
 Force exerted by jet on plate along x – direction = Fx = m (Ux -

Vx) Fx = av [V - 0]
2
Fx = av
Work done by the jet = Force x Velocity of plate

(iv) Force x 0
(v) 0
Case-II
To compute the impact of jet on a stationary flat plate held inclined to the
direction of jet.
NORMAL TO PLATE
V
y
V x
(90 )

Force exerted by jet on vane along normal direction.
(iv) Fn = m [Un – Vn]
smartworlD.asia
Fn = aV [(Vsin) – O]
2
Fn = aV sin]
Fy
Fn
(90 - )
Fx
Fx = Fn cos (90 - )
2
Fx = [aV sin] sin
2 2
Fx = aV sin 
Fy = Fn sin (90 - )
2
Fy = [aV sin] cos
2
Fy = aV sin cos
Work done by the jet on vane

(viii) Force x Velocity of vane
(ix) Force x 0
(x) 0
Case-III
To compute the impact of jet on a moving flat plate held normal to the jet.
y (V – U)
x
V U
(V – U)
smartworlD.asia
V = Velocity of jet striking the plate
U = Velocity of vane along the direction of vane.
Adopting the concept of relative velocity, the system can be considered to be

a stationary plate, the jet striking the vane with a relative velocity (V – U).
 m = Q 
a(V - U)
2
Fx = a(V - U)
Work done by the jet on plate = Force x Velocity of

2
plate = a (V - U) x U
Case-IV
To compute the impact of jet on a moving flat plate held inclined to the
direction of jet.
V U
 (V - U)
V = Velocity of jet
U = Velocity of plate along the direction of jet.
Adopting the concept of relative velocity, the above case can be considered
to be fixed vane with a jet velocity of (V – U).
smartworlD.asia
Fn = a (V – U)
2
2
Fx = a (V - U) sin 
2
2
Fy = a (V - U) sin cos
Work done by the jet on vane plate along x – direction

= Fx x Velocity of plate along x – direction
2 2
= a (V - U) sin  U
Case-V
x


V
m = aV
smartworlD.asia
= Fx = m [Ux – Vx]
Fx = (aV) [V – (–Vcos)]
2
Fx = aV (1 + cos]
Case-VI
To compute the impact of jet on a moving symmetrical curved plate, the jet
x

U
V
Adopting relative velocity concept, the system can be considered to be a jet

of relative velocity (V – U) striking a fixed plate.
smartworlD.asia
(V – U)


(V – U)
m = a (V – U)
Fx = m [Ux – Vx]
Fx = a (V – U) [(V – U) – (–V – U) cos]
2
Fx = a (V – U) (1 + cos]
Work done by the jet on plate = Force x Velocity of date

= Fx U
2
= a(V – U) (1 + cos] U
Case-VII
striking the plate at one of the tips tangentially.
x


smartworlD.asia
V
m = aV
Fx = m [Ux – Vx]
Fx = aV [Vcos – (–Vcos)]
2
Fx = aV (1 + cos]
Fy = m [Uy – Vy]
Fx = aV [Vsin – Vsin]
Fx = 0
IMPACT OF JET ON VANES

Session – III
 Problems - 1 
A jet of water 50 mm diameter strikes a flat plate held normal to the
direction of jet. Estimate the force exerted and work done by the jet if.
(viii) The plate is stationary
(ix) The plate is moving with a velocity of 1 m/s away from the jet along
the line of jet.
(x) When the plate is moving with a velocity of 1 m/s towards the jet along
the same line.
The discharge through the nozzle is 76 lps.
 Solution: 
-3
d = 50 mm = 50 x 10 m
II -3 2
a= x (50 x 10 )
smartworlD.asia
4
-3 2
a = 1.9635 x 10 m
Q = aV
-3 -3
76 x 10 = 1.9635 x 10 x V
V = 38.70 m/s
Case a) When the plate is stationary

2
Fx = aV
-3 2
Fx = 1000 x (1.9635 x 10 ) x (38.70)
Fx = 2940.71 N
Work done/s = Fx x U
Work done/s = F x x 0
Work done/s = 0
Case b) V = 38.70 m/s ()

U = 1 m/s ()
2
Fx = a (V - U)
-3 2
Fx = 1000 x 1.9635 x 10 x (38.7 - 1)
Fx = 2790 TN
Work done/s = F x x U
Work done/s = 2790.7 x 1
Work done/s = 2790.7 Nm/s or J/s or W
Case c) V = 38.70 m/s ()

U = 1 m/s ()
2
Fx = a (V - U)
-3 2
Fx = 1000 x 1.9635 x 10 x (38.7 + 1)
Fx = 3094.65 N
smartworlD.asia
Work done/s = 3094.65 x 1
Work done/s = 3094.65 Nm/s
 Problems - 2 
A jet of water 50 mm diameter exerts a force of 3 kN on a flat vane held
perpendicular to the direction of jet. Find the mass flow rate.
 Solution: 
-3
d = 50 mm = 50 x 10 m
II -3 2
a= x (50 x 10 )
4
-3 2
a = 1.9635 x 10 m
2
Fx = aV
-3 2
3000 = 1000 x 1.9635 x 10 x V
V = 39.09 m/s
m = Q
m = aV
-3
m = 1000 x 1.9635 x 10 x 39.09
m = 76.75 kg/s
Problems - 3 
A jet of data 75 mm diameter has a velocity of 30 m/s. It strikes a flat plate
o
inclined at 45 to the axis of jet. Find the force on the plate when.
The plate is stationary
The plate is moving with a velocity of 15 m/s along and away from the jet.
Also find power and efficiency in case (b)
 Solution:
-3 -3 2
d = 75 x 10 m a = II x (75 x 10 )
4
-3 2
V = 30 m/s a = 4.418 x 10 m
smartworlD.asia
o
 = 45
Case a) When the plate is stationary

2 2
Fx = aV sin 
-3 2 2
1000 x 4.418 x 10 x 30 x Sin 45
1988.10 N
Case b) When the plate is moving

V = 30 m/s ()
U = 15 m/s ()
2 2
Fx = a (V - U) sin 
-3 2 2
Fx = 1000 x 4.418 x 10 x (30 - 15) sin 45
Fx = 497.03 TN
Output power = Work done/s

Output power = Fx x U
Output power = 497.03 x 15
Output power = 7455.38 W
Input power = Kinetic energy of jet/s

1 2
Input power = x mxV
2
1
x aVx V
2
Input power =
2
1 3 3
Input power = x1000 x 4.418 x10 x 30
2
Input power = 59643 W
O/P
Efficiency of the system = x100
I/P
7455.38
Efficiency of the system =
smartworlD.asia
x100 59643
Efficiency of the system = 12.5%
 Problem – 4 
A 75 mm diameter jet having a velocity of 12 m/s impinges a smooth flat
o
plate, the normal of which is inclined at 60 to the axis of jet. Find the impact of jet
on the plate at right angles to the plate when the plate is stationery.
What will be the impact if the plate moves with a velocity of 6 m/s in the
direction of jet and away from it. What will be the force if the plate moves towards
the plate.
 Solution 
-3
d = 75 x 10 m

x 75 x10 2
3
a=
4
-3 2
a = 4.418 x 10 m
Normal
o
60
o
 = 30
When the plate is stationery

2
Fn = aV sin
-3 2
Fn = 1000 x (4.418 x 10 ) 12 sin30
Fn = 318.10 N
When the plate is moving away from the jet

2
Fn = a (V – U) sin
smartworlD.asia
-3 2
Fn = 1000 x 4.418 x 10 (12 – 6) sin30
Fn = 79.52 N
When the plate is moving towards the jet

2
Fn = a (V + U) sin
-3 2
Fn = 1000 x 4.418 x 10 (12 + 6) sin30
Fn = 715.72 N
 Problem – 5 
A vertical flat plate is hinged at its top. A jet of water strikes at the centre of
the plate. Due to the impact of jet, the plate attains equilibrium at an angle ‘’ with
aV 2
the vertical. Show that sin =
where W
 – Mass density of fluid

a – area of cross section of jet.
V – Velocity of jet
W – Weight of the plate
 Solution 
x
Hinge
Hinge
 W
x x
Fn
INITIAL FINAL
smartworlD.asia  x W
x
90 - C
B
C
Fn
MHinge = 0
– Fn x AB + W x CA sin = 0
2 x
– aV sin (90 - )  + W  x sin = 0
cos 
2
aV = W sin
2
sin = aV
W
 Problem – 6 
A square plate weighing 140 N has an edge of 300 mm. The thickness of the
plate is uniform. It is hung so that it can swing freely about the upper horizontal
edge. A horizontal jet of 20 mm diameter having 15 m/s velocity impinges on the
plate. The centre line of jet is 200 mm below. The centre line of jet is 200 mm below
the upper edge of plate. Find what force must be applied at the lower edge of plate in
order to keep it vertical.
200
Fx 300
smartworlD.asia 300
P
Hinge
0.2 m
0.3 m
W = 140 N
Fn

a x 20 x 103 2
4
-6 2
a = 314.16 x 10 m
V = 15 m/s
MHinge = 0
Fx x 0.2 + P x 0.3 = 0
2
aV = 0.2 = P x 0.3
-6 2
1000 x 314.16 x 10 x 0.2 x 15 = P x 0.3
P = 47.12 N
Show that the force exerted by a jet on a hemispherical stationery vane is
twice the force exerted by the same jet on flat stationery normal vane.
smartworlD.asia Fx = aV
2
(DERIVE)
(DERIVE)
2
Fx = aV (1 + cos)
2
= aV (1 + cos)
2
= 2aV
2
Fx 2  2aV
Fx1 aV2
 Fx2 = 2Fx1 


A jet of water of diameter 50 mm strikes a stationary, symmetrical curved plate
with a velocity of 40 m/s. Find the force extended by the jet at the centre of plate along
o
its axis if the jet is deflected through 120 at the outlet of the curved plate.
Solution:
o
Angle of deflection = 120
smartworlD.asia
-3
d = 50 x 10 m

a= x 50 x103 2
4
-3 2
a = 1.963 x 10 m
V = 40 m/s
o
 = 60
2
Fx = aV (1+ cos)
-3 2
Fx = 1000 x 1.963 x 10 x 40 (1 + cos60)
Fx = 4711-2 N
A jet of water strikes a stationery curved plate tangentially at one end at an
o
angle of 30 . The jet of 75 mm diameter has a velocity of 30 m/s. The jet leaves at
o
the other end at angle of 20 to the horizontal. Determine the magnitude of force
exerted along ‘x’ and ‘y’ directions.
Solution:
30 m/s
o
20 x
o
30
smartworlD.asia
30 m/s
d = 50 x 10 m
-3

x 75 x10 2
3
a=
4
-3 2
a = 4.418 x 10 m
Fx = m [Ux - Vx]
Fx = aV [30 cos 30 – (-30 cos 20)]
-3
Fx = 1000 x 4.418 x 10 x 30 (30 cos 30 + 30cos20)
Fx = 7179.90 N
10
A jet of water of diameter 75 mm strikes a curved plate at its centre with a
velocity of 25 m/s. The curved plate is moving with a velocity of 10 m/s along the
o
direction of jet. If the jet gets deflected through 165 in the smooth vane, compute.
a) Force exerted by the jet.
b) Power of jet.
c) Efficiency of jet.
-3
d = 75 mm = 75 x 10 m

x 75 x10 
3 2
a=
4
-3 2
a = 4.418 x 10 m
Solution:
smartworlD.asia 165
o
o
 = 15
V = 25 m/s
U = 10 m/s
2
Fx = a (V – U) (1 + cos)
-3 2
Fx = 1000 x 4.418 x 10 [25 – 10] x (1 + cos 15)
Fx = 1954.23 N
11
Power of jet = Work done/s

Power of jet = F x x U
Power of jet = 1954.23 x 10
Power of jet = 19542.3 W
1 2
Kinetic energy of jet/s = mV
2
Kinetic energy of jet/s =

1
2
 3

1000 x 4.418 x10 x 25 25
2
Kinetic energy of jet/s = 34515.63 W
 = Out put
In put 
= 19542.3
34515.63 
 = 56.4 % 
smartworlD.asia
12

Session – IV
 Problems - 11 
A symmetrical curved vane is moving with a velocity of ‘U’ and a jet of
velocity ‘V’ strikes at the centre along the direction of motion.
Derive expressions for
(xi) Force exerted along the direction of motion.
(xii) Work done/s.
(xiii) Efficiency of the system.
(xiv) Maximum efficiency.
 Solution 
2
Fx = a (V - U) (1 + cos)
2
Work done/s = a (V - U) (1 + cos) U
Work done / s
Efficiency =
smartworlD.asia
K.E.sup plied / s
 = aV U 1cos U

2
1
2
 = aV U11cos
2
U x aV . V2
2
 = 2V  U 1  cos
2
 U V 3
 = 2 V U  2U V  U 1 
2 2 3
cos U V
3
For maximum efficiency

d = 0
dU
= 0 = 2V  4UV 3U 1cos 

2 2
d
3
dU V
2 2
V – 4UV + 3U = 0
(V – 3U) (V – U) = 0
V – 3U = 0 or V–U=0
(V – U)  0
V
 V = 3U or U =
3
1
For maximum efficiency velocity of vane should be x velocity of jet 3
2V  U 1cos  U
2
max = 3
V
Substituting U = V
3
16 2 
max = cos  
27  2
if the vane is hemispherical  = 0
16
max =
27
max = 59.25%

smartworlD.asia
Problems - 12 
o
A jet of water from a nozzle is deflected through 60 from its direction by a
curved plate to which water enters tangentially without shock with a velocity of
30m/s and leaver with a velocity of 25 m/s as shown in figure. If the discharge from
the nozzle is 0.8 kg/s, calculate the magnitude and direction of resultant force on the
vane.
 Solution 
25 m/s
o
60 x
25 m/s
m = 0.8 kg/s
Fx = m (Ux - Vx)
Fx = 0.8 (30 – 25 cos60)
Fx = 14 N ()
Fy = m (U y – Vy)
Fy = 0.8 (0 – 25 sin60)
Fy = 17.32 N ()
Fx = 14 N

Fy = 17.32 N
smartworlD.asia
 
R=
R = 22.27 N
Fx2 Fy
2
-1
 Fy 
 = tan  

 F
 x 
= 51.05
 Problems - 13 
A jet of water 50 mm in diameter impinges on a fixed cup which deflects the
o
jet by 165 as shown in figure. If the reaction of the cup was found to be 26.5 N
when the discharge was 980 N/minute compute the ratio of.
Actual force to theoretical force of jet.
Velocity of outlet to velocity at inlet.
 Solution 
30 m/s
o
165
 
V = 9.45 m/s  
-3
d = 50 x 10 m
 -3 2
== (50 x 10 )
4
-3 2
a = 1.963 x 10 m
smartworlD.asia
 = 15
W m g
o
980
m x 9.81
60
m = 1.665 kg/s
Fx = m (Ux – Vx)
Fx = 1.665 (9.45 + 9.45 cos
15) Fx = 30.93 N
F 26.5
act =
Fth 30.93
Fact
= 0.857
F
th
Let, V1 be the actual velocity at

out Fx act = m ( Ux – Vx)
26.5 = 1.665 (9.45 + V1 cos15)

V1 = 6.964 m/s
Velocity at outlet  6.694

Velocity at inlet 6.45
Velocity at outlet 
0.708
Velocity at inlet
 Problem – 14 
In a laboratory setup, a symmetrical curved vane which deflects the
o
centerline of jet by 30 support a total mass of 180 grams. Determine the discharge
that must be supplied for balancing the vane. The jet diameter is 5 mm and vane co-
efficient is 0.75.
Factual
Note: Co-efficient of impact = Ci =
F
theoretical
smartworlD.asia
30 30
-3 2
d = 5 x 10 m

d= x 5x103 2
4
-5 2
a = 1.963 x 10 m
W = mg
W = 0.180 x 9.81
W = 1.7658 N
F
Ci = act
F
th
1.7658
0.75 =
F
theoretical
1.7658
 Theoretical =
0.75
= 2.3544 N
2
F = aV (1 + cos)
-3 2
2.354 = 1000 x 1.963 x 10 x V (1 + cos30)
2
V = 0.6426
V = 0.8016 m/s
Q = aV
-5
Q = 1.963 x 10 x 0.8016
-5 3
Q = 1.5735 x 10 m /s
Case-VIII
smartworlD.asia
To derive expressions for the force exerted, work done and efficiency of
impact of jet on a series of flat vanes mounted radially on the periphery of a circular
wheel.
OR
To show that efficiency of impact of jet on radially mounted flat vanes is
50% when the jet strikes normally on the vane.
smartworlD.asia V U
Let us consider flat vanes mounted radially on the periphery of a circular

wheel. V is the velocity of jet and ‘U’ is the velocity of vane. The inpact of jet on
vanes will be continuous since vanes occupy one after another continuously.
Fx = m (Ux – Vx)
Fx = aV [(V – U) – 0]
Fx = aV (V – U)
Work done/s or Power = Fx U

Power = aV (V – U) U
O/P
Efficiency =  =
I/P
 = aVV  UU
1
aVV 2
2
 = 2V  UU
2
V
Conduction for maximum efficiency:

2 VU  U 2 
= 2
V
d 0
dU
d 0 = 2 V  2U
2
dU V
V
U  2
 Efficiency is maximum when the vane velocity is 50% of velocity of jet.
 VV
smartworlD.asia
2V  
 max =
 22
1 V2
=
2
= 50%
Case-IX
To derive expression for the force exerted, power and efficiency of impact of
jet on a series of symmetrical curved vanes mounted on the periphery of a wheel.
smartworlD.asia 

Fx = (aV) (Ux – Vx)

Fx = (aV) [(V – U) + (V – U) cos]
Fx = aV [(V – U) (1 + cos)
Power = work done/s

Power = Fx x U
Power = aV(V – U) (1 + cos) U
1
Input = mV2
2
1
Input = a V3
2
=O/P
I/P
 = aVV  U1  cos U

1
aV3
2
 = 2V  1U1  cos U

aV3
2
Condition for maximum efficiency
 = 2VU  U 1  cos

2
U V 2

d 2
0 V  2U1  cos 
dU V 2
V – 2U = 0
V
U=
smartworlD.asia
2
1
Vane velocity = x velocity of jet
2
 V V
2V  1  cos 
 2 2
max =
V2
1  cos 
max =
2
If the vanes are hemispherical  = 0

H cos 
max =
2
max = 1 or 100%
10

Session – V
Case X: Force exerted by a jet of water on an asymmetrical curved vane when

the jet strikes tangentially at one of the tips:
U2 = U Vw2
2
V2 2
Vr2 Vf2OUTLET VELOCITY TRIANGLE

y
2
U 1 x
smartworlD.asia
V1

Vf1
1 1 Vr1
INLET VELOCITY TRIANGLE

U
Vw1
Fx = m [Ux - Vx]
Fx = aVr1 [(Vw1 – U) – (-(Vw2 + U))]
Fx = aVr1 [Vw1 + Vw2]
Vw2
2
Vr2 V2
Fx = aVr1 [(Vw1 - U) – (-(U – Vw2))]

Fx = aVr1 [Vw1 – Vw2]
Fx = aVr1 [Vw1 ± V w2]
Work done/s = aVr1 [Vw1 ± V w2] U
Work done for unit mass flow rate = [Vw1 ± V w2] U

U
Work done for unit weight flow rate = [V w1 ± V w2]
g
 Problem: 
A jet of water impinges a curved plate with a velocity of 20 m/s making an
o o
angle of 20 with the direction of motion of vane at inlet and leaves at 130 to the
direction of motion at outlet. The vane is moving with a velocity of 10 m/s.
Compute.
(xv) Vane angles, so that water enters and leaves without shock.
(xvi) Work done/s
smartworlD.asia
 Solution: 
U Vw2
 2 o
50 Vf2
Vr2 V2
130o
V1
Vf1
o Vr1
1 = 20 1
U
Vw1

V1 = 20 m/s
U1 = U2 = 10 m/s
Assuming number loss Vr1 = Vr2
Vw1 = 20 cos 20 = 18.79 m/s
Vf1 = 20 sin 20 = 6.84 m/s
V
f1
tan  1 = Vw1 U

6.84
tan  1 = 18.79 10
o
tan  1 = 37.88
Vf 1
sin  1 =
V
r1
6.84
sin 37.88 =
V
r1
smartworlD.asia
Vr1 = 11.14 m/s
Vr2 = Vr1 = 11.14 m/s
V
r2  U
sin130 sin (180 130 2 )
10 sin130
sin (150 - 2) =
11.14
sin (50 -  2) = 0.6877

o
 2 = 6.55
Work done per unit mass flow rate

(viii) (Vw1 + Vw2) U
(ix) [18.79 + (Vr2 cos  2 -
U)]
(x) [18.79 + 11.14 cos 6.55 -
10] 10
(xi) 198.57 W/kg

Case XI: Work done by water striking the vanes of a reaction turbine.
Note:
D2
2 R2
D1 U2
2
2
R1
U1
1
smartworlD.asia
U1 =
D1 N
60
U1 = R1
N
U2 D2 = R2
= U2
60
2. Angular Momentum Principle:

Torque = Rate of change of angular momentum
T = (Q)  [Vw1 R1 – Vw2 R2]

Vw2
U2
2
Vr2 V2 2
Vf2

V1 Vr1 Vf1
1
1
U1
Vw1
 smartworlD.asia
- Inlet tip 
 - Outlet tip 
U1 D1 N
- Tangential velocity of wheel at inlet =
60
U2 D 2 N
- Tangential velocity of wheel at outlet =
60
V1 - Absolute velocity of fluid at inlet
V2 - Absolute velocity of fluid at outlet
Vw1 - Tangential component of absolute velocity at inlet – velocity of wheel
at inlet = V1 cos 1.
Vw2 - Tangential component of absolute velocity at outlet – velocity of wheel
at outlet = V2 cos 2.
Vf1 - Absolute velocity of flow at inlet
Vf2 - Absolute velocity of flow at outlet
Vr1 - Relative velocity at inlet
Vr2 - Relative velocity at outlet
1 - Guide angle or guide vane angle at inlet

1 - Vane angle at inlet

2 - Vane angle at outlet
By angular momentum equation
T = m [Vw1 R1 – (-Vw2 R2)]

T = m [Vw1 R1 + Vw2 R2]
T = m [Vw1 R1 ± Vw2 R2] ----- (1)
Work done/s or power = T x Angle velocity

Work done/s or power = T 
Work done/s or power = m [Vw1 R1 ± V w2 R2] 

Work done/s or power = m [Vw1 (R1) ± V w2 (R2)]
Work done/s or power = m [Vw1 U1 ± V w2 U2]
Work done per unit mass flow rate = [Vw1 U1 ± V w2 U2]

1 (V U ± V U )
Work done per unit weight flow rate = w1 1 w2 2
smartworlD.asia
g
m V U V U 
Efficiency of the system =  = w1 1 w2 2
1 2
m V1
2
2 V U V U 
= w1 1 w2 2
2
V1
 Problem: 
A jet of water having a velocity of 35 m/s strikes a series of radial curved
o
vanes mounted on a wheel. The wheel has 200 rpm. The jet makes 20 with the
o
tangent to wheel at inlet and leaves the wheel with a velocity of 5 m/s at 130 to
tangent to the wheel at outlet. The diameters of wheel are 1 m and 0.5 m. Find
Vane angles at inlet and outlet for radially outward flow turbine.
Work done
Efficiency of the system

 Solution 
V1 - 35 m/s
N - 200 rpm
o
1 - 20
o
2 - 180 – 130 = 50
V2 - 5 m/s
D1 - 1m
D2 - 0.5 m
U1 = D1 N
60
U1 = x1x 200
60
U1 = 10.47 m/s
U2 = D 2 N
smartworlD.asia
60
U2 = x 0.5 x 200
60
U2 = 5.236 m/s
Vw1 = V1 cos 1
Vw1 = 35 cos 20
Vw1 = 32.89 m/s
Vf1 = V1 sin 1
Vf1 = 11.97 m/s
V1
Vr1 Vf1
1U 1 1
Vw1

V
f1
tan  1 = V U 
w1 1
11.97
tan  1 = 32.89 10.47
o
 1 = 28.10
Vw2
U2
2
Vf2
Vr2
Vf2 = 5 sin 50
Vf2 = 3.83 m/s
smartworlD.asia
Vw2 = 5 cos 50
Vw2 = 3.214 m/s
V
f2
tan 2 = U V
2 w2
3.83
tan 2 =
5.236 3.214
o
tan  2 = 24.38
Work done per unit mass flow rate = [Vw1 U1 + Vw2 U2]
Work done per unit mass flow rate = [32.89 x 10.47 + 3.214 x
5.236] Work done per unit mass flow rate = 362.13 W/kg
2V U  V U 
Efficiency =  = 1 1 2 2
2
V1
Efficiency =  = 232.89 x10.47  3.214 x

5.236 35
2
Efficiency =  = 0.5896 or 58.96 %
8
DIMENSIONAL ANALYSIS
Session – VI
It is a mathematical technique which makes use of study of dynamics as an

art to the solution of engineering problems.
 Fundamental Dimensions 

All physical quantities are measured by comparison which is made with
respect to a fixed value.
Length, Mass and Time are three fixed dimensions which are of importance
in fluid mechanics and fluid machinery. In compressible flow problems, temperature
is also considered as a fundamental dimensions.
 Secondary Quantities or Derived Quantities 

Secondary quantities are derived quantities or quantities which can be
expressed in terms of two or more fundamental quantities.
smartworlD.asia
 Dimensional Homogeneity 
In an equation if each and every term or unit has same dimensions, then it is
said to have Dimensional Homogeneity.
V = u + at
2
m/s m/s m/s  s
-1 -1 -2
LT = (LT ) + (LT ) (T)
 Uses of Dimensional Analysis 

It is used to test the dimensional homogeneity of any derived equation.
It is used to derive equation.
Dimensional analysis helps in planning model tests.
 Dimensions of quantities 

o o
1. Length LM T
o o
2. Mass L MT
o o
3. Time L M T
2 o o
4. Area LMT
3 o o
5. Volume LMT

o -1
(iii) Velocity LM T
o -2
(iv) Acceleration LM T
-1
(v) Momentum LMT
-2
(vi) Force LMT
2 -2
(vii) Moment or Torque L MT
-2
(viii) Weight LMT
-3 o
(ix) Mass density L MT
(x) Weight density L-2MT-2
o o o
(xi) Specific gravity LM T
(xii) Specific volume L3M-1To
(xiii) Volume flow rate L3MoT-1
(xiv) Mass flow rate LoMT-1
-3
(xv) Weight flow rate LMT
(xvi) Work done L2MT-2
2 -2
(xvii) Energy L MT
2 -3
(xviii) Power L MT
o -2
(xix) Surface tension L MT
(xx)
(xxi) smartworlD.asia
Dynamic viscosity
Kinematic viscosity
(xxii) Frequency
L-1M+1T-1
L2MoT-1
LoMoT-1
(xxiii) Pressure L-1MT-2
(xxiv) Stress L-1MT-2
(xxv) E, C, K L-1MT-2
-1 2
(xxvi) Compressibility LM T
(xxvii) Efficiency LoMoTo
(xxviii) Angular velocity LoMoT-1
-2
(xxix) Thrust LMT
(xxx) Energy head (Energy/unit L2MoT-2
mass) o o
LM T
(xxxi) Energy head (Energy/unit
weight)

2
DIMENSIONAL ANALYSIS
Session – VII
 Methods of Dimensional Analysis 
There are two methods of dimensional analysis.
Rayleigh’s method
Buckingham’s ( – theorem) method
Rayleigh’s method
Rayleigh’s method of analysis is adopted when number of parameters or
variables are less (3 or 4 or 5).
Methodology
X1 is a function of
X2, x3, X4, ……, Xn then it can be written as
X1 = f(X2, x3, X4, ……, Xn)
a b c
X1 = K (X2 , x3 , X4 , ……)
smartworlD.asia
Taking dimensions for all the quantities
a b c
[X1] = [X2] [X3] [X4] ……
Dimensions for quantities on left hand side as well as on the right hand side
are written and using the concept of Dimensional Homogeneity a, b, c …. can be
determined.
Then,
a b c
X1 = K  X2  X3  X4  ……
 Problems 1: Velocity of sound in air varies as bulk modulus of electricity K, 

K
Mass density . Derive an expression for velocity in form C =

 Solution:
C = f (K, )
a b
C = M  K 
M – Constant of proportionality
1
a b
[C] = [K]  []
o -1 -1 -2 a 3 ob o -1
[LM T ] = [L MT ] [L MT ] C – Velocity – LM T
K – Bulk modulus – L-1 MT-2
-3 o
[LM T ] = [L o -1 -a+(-36) M T ]
a+b -2a  - Mass density – L MT
- a – 3b = 1
a+b=0
- 2b = 1
1
b=
2
1
a=
2
C = MK1/2 -1/2
K
C=M

If, M = 1, C =
K

smartworlD.asia
 Problem 2: Find the equation for the power developed by a pump if it depends
on bead H discharge Q and specific weight  of the fluid. 

 Solution: 
P = f (H, Q, )
a b c
P = K  H  Q 
a b c
[P] = [H]  [Q]  []
2 -3 o oa -2 -2 b -2 -2 c
[L MT ] = [LM T ]  [L MT ]  [L MT ]
2 = a + 3b – 2c 2 -3
1=c Power = L MT
o o
-3=-b-2 Head = LM T
3 o -1
Discharge =L M T
-2 -2
-3= -b–2 Specific Weight = L MT
b=-2+3
b=1
2=a+3–2
a=1

1 1 1
P = K  H  Q 
P = K  H  Q 
When, K=1
P = H  Q 
 Problem 3: Find an expression for drag force R on a smooth sphere of diameter D

moving with uniform velocity V in a fluid of density  and dynamic viscosity .. 


 Solution: 
R = f (D, V, , )
a b c d
R = K  D  V  , 
a b c d
[R] = [D]  [V]  []  []
-2 o oa o -1 b -3 o c -1 -1 d
[LMT ] = [LM T ]  [LM T ]  [L MT ]  [L MT ]
c+d=1 -2
Force = LMT
smartworlD.asia
c=1–d o o
Diameter = LM T
o -1
Velocity = LM T
–b–d=–2 3 o
b=2–d Mass density = L MT
1 = a + b – 3c – d
1 = a + 2 – d – 3 (1 – d) – d
1 = a + 2 – d – 3 + 3d – d
a=2–d
2-d 2-d 1-d d

R=KD V  ,
Dd2  Vd2  d

R=K  d
D V 
d
2 2  
R = K  V D  
VD 
2 2 
R = V D   
 
VD 

2  VD 
R = V 2
D  

  
2 2
R = V D  [NRe]
smartworlD.asia

 Problem 4: The efficiency of a fan depends on the density  dynamic viscosity

, angular velocity , diameter D, discharge Q. Express efficiency in terms of
dimensionless parameters using Rayleigh’s Method. 
o o o
 - L M T
 Solution:  -3 o
 - L MT
 = f (, , , D, Q)  -1 -1
a b c d e  - L MT
 = k     D  Q  o o -1
a b c d e -L M T
[] = []  []  []  [D]  [Q] o o
D - LM T
o o o -3 oa -1 -1 b o o -1 c o od
[L M T ] = [L MT ]  [L MT ]  [L M T ]  [LM T ] 
3 o -1 -1 o o o
[L M T ]  [L M T ]  [L-3a-b+d+3e  Ma+b  T-b-c-e]
a+b=0
a=–b
–b–c–e=0
c=–b–e
smartworlD.asia
– 3a – b + d + 3e = o
+ 3b – b + d + 3e = 0
d = – 2b – 3e
-b b -b-e
 = K     D-2b-3e  Q e
1 b 1 1 2
 = K  b  be  D  D3 

2 b e
Q
e

=K


b   Q 
 2  3 
 D   D 
  Q 
=Q  2 , 3 
 D D 

 Problem 5: The capillary rise H of a fluid in a tube depends on its specific weight 
H  
 and surface tension  and radius of the tube R prove that .
 2 
R  R 
 Solution: 
H = f (, , R)
a b c
H = K    R
a b c
[H] = []  []  [R]
o o -2 -2 a o -2 b o oc
[LM T ] = [L MT ]  [L MT ]  [LM T ]
[LMoTo] =  [L-2a+c  Ma+b  T -2a-2b] o o
H - LM T
–2a + c = -2 -2
 - L MT 

1a+b=0 o -2
- L MT
–2a – 2b = 0 o o
R - LM T 
 c 1  a
=   2

smartworlD.asia
c 1
b
02
1cb=
  2 
 c1  1c
 
2 c
H=K   2    R
c 1
H=K    c  R
2 2 c
1
 2  2
c
H=K   2
 
1
2
 Rc
1 c
R  2  2 R
 12  12
H  

=K 
  c 1 1
R
2
R   2  
-b b 1-2b
H = K    R
b
 R
  R 
b 2
H=K b

b
  
H=K  2
 R 
  
  
.
2
 R R 
H
2. Buckingham’s  Method
This method of analysis is used when number of variables are more.
Buckingham’s  Theorem
If there are n – variables in a physical phenomenon and those n-variables
contain ‘m’ dimensions, then the variables can be arranged into (n-m) dimensionless
groups called  terms.
Explanation:
If f (X1, X2, X3, ……… Xn) = 0 and variables can be expressed using m
dimensions then.
f (1, 2, 3, ……… n - m) = 0
smartworlD.asia
Where, 1, 2, 3, ……… are dimensionless groups.
Each  term contains (m + 1) variables out of which m are of repeating type

and one is of non-repeating type.
Each  term being dimensionless, the dimensional homogeneity can be used

to get each  term.
 Selecting Repeating Variables 

1. Avoid taking the quantity required as the repeating variable.
2. Repeating variables put together should not form dimensionless group.
3. No two repeating variables should have same dimensions.
4. Repeating variables can be selected from each of the following properties.
a. Geometric property  Length, height, width, area
b. Flow property  Velocity, Acceleration, Discharge
c. Fluid property  Mass density, Viscosity, Surface tension

DIMENSION ANALYSIS
Session – VIII
Problem 1: Find an expression for drag force R on a smooth sphere of diameter D

moving with uniform velocity V in a fluid of density  and dynamic viscosity ..
 Solution: 
-2
f(R, D, V, , ) = 0 R = LMT
o o
D = LM T
Here, n = 5, m = 3 -1
V = LT
-3
 Number of  terms = (n – m) = 5  = ML
-1 -1
 –3=2  = L MT
 f (1, 2, 3) = 0 
Let D, V,  be the repeating variables.
a1 b1 c1
1 = D V  R
a1 b1 -3 c1
smartworlD.asia
o o o -1 -2
[L M T ] = [L] [LT ] [ML ] [LMT ]
a b c c -b
LoMoTo = [L] 1+ 1-3 1+1 [M] 1+1 [T] 1-2
(xi) b
1=2
b1 = –2
c1 + 1 = 0
c1 = – 1
a1 + b1 – 3c1 + 1 = 0
a1 + 2 + 3 + 1 = 0
a1 = – 2
-2 -2 -1
1 = D  V   R
R
1 = 2 2
D V 
a2 b2 c2
2 = D V  
a b c
o o o 2 -1 2 -3 2 -1 -1
[L M T ] = [L] [LT ] [ML ] [L MT ]
a b -3c -1 c +1 -b -1
[LoMoTo] = [L] 2+ 2 2 [M] 2 [T] 2
– b2 – 1 = 0

b2 = – 1
c2 = – 1
a2 + b2 – 3c2 – 1 =
0 a2 – 1 + 3 – 1 = 0
a2 = – 1
-1 -1 -1
2 = D  V  
2 = 
VD
f (1, 2) = 0
 R  
f ,  =0
 2 2 
D V  VD 
R   
 
2 2  
D V VD 
smartworlD.asia
R V
 VD 
2
D
2   




 Problem 2: The efficiency of a fan depends on density , dynamic viscosity

, angular velocity , diameter D and discharge Q. Express efficiency in terms
of dimensionless parameters. 


 Solution: 
o o o
f (, , , D, Q) = 0 =L M T
-3
 = ML
Here, n = 6, m = 3 -1 -
 = L MT
 Number of  terms = 3  1 -1
 =T
 f (1, 2, 3) = 0  D=L
3 -1
Q=L T
Let, D, ,  be the repeating variables.
a1 b1 c1
1 = D   
o o o a1 -1 b1 -3 c1 -1 -1
[L M T ] = [L] [T ] [ML ] [L MT ]
a -3c c +1 -b -1
[LoMoTo] = [L] 1 1-1 [M] 1 [T] 1
b1 = – 1
2
c1 = –1
a1 – 3 c1 – 1 =
0 a1 = –2
-2 -1 -1
1 = D   

1 =
D2 . . 
a2 b2 c2
2 = D   Q
o o o a2 -1 b2 -3 c2 3 -1
[L M T ] = [L] [T ] [ML ] [L T ]
o o o a2+3-3C2 c2 -b2-1
[L M T ] = [L] [M] [T]
c2 = 0
-b2 - 1 =
0 b2 = – 1
a2 + 3 – 3c2 = 0
a2 + 3 = 0
a2 = -3
smartworlD.asia
2 = D
-3
Q
-1
   Q
o
2 =
D3
a3 b3 c3
3 = D   
o o o a3 -1 b3 -3 c3 o o o
[L M T ] = [L] [T ] [ML ] [M L T ]
a c c -b
[LoMoTo] = [L] 3-3 3 [M] 3 [T] 3
b3 = 0
c3 = 0
a3 = 0
3 = 
f (1, 2, 3) = 0
   
 
,
D2
f  3 , =0
  D 
   
 
 
2 , 3 
D
  D 

 Problem 3: The resisting force of a supersonic plane during flight can be
considered as dependent on the length of the aircraft L, velocity V, viscosity ,
mass density , Bulk modulus K. Express the fundamental relationship between
resisting force and these variables. 

 Solution: 
f (R, L, K, , , V) = 0
n=6
  Number of  terms = 6 – 3 = 3 
 f (1, 2, 3) = 0 
Let, L, V,  be the repeating variables.

a1 b1 c1
1 = L V  K
o o o a1 -1 b1 -3 c1 -1 -2
L M T = [L] [LT ] [ML ] [L MT ]
a b -3c -1 c +1 -b -2
L M T = [L]
o o o 1+ 1 1 [M] 1 [T] 1
smartworlD.asia
b1 = –2
c1 = –1
a1 + b1 – 3c1 – 1 =
0 a1 – 2 + 3 – 1 = 0
a1 = 0
o -1 -1
1 = L  V   K
K
2
1 = V 
a2 b2 c2
2 = L V  R
o o o a2 -1 b2 -3 c2 -2
L M T = [L] [LT ] [ML ] [LMT ]
a b 3c +1 c +1 -b -2
LoMoTo = [L] 2+ 2- 2 [M] 2 [T] 2
-b2 – 2 =
0 b2 = – 2
c2 = – 1

a2 + b2 – 3c2 + 1 =
0 a1 + 2 + 3 + 1 = 0
a2 = –2
-2 -2 -1
2 = L  V   R
R
2 = 2
L V 2
a3 b3 c3
3 = L V  
o o o a3 -1 b3 -3 c3 -1 -1
L M T = [L] [LT ] [ML ] [L MT ]
a b 3c -1 c +1 -b -1
LoMoTo = [L] 3+ 3- 3 [M] 3 [T] 3
-b3 – 1 =
0 b3 = – 1
c3 + 1 = 0
c3 = – 1
smartworlD.asia
a3 + b3 – 3c3 – 1 =
0 a1 – 1 + 3 – 1 = 0
a3 = –1
-1 -1 -1
3 = L  V  
2 = 
LV 
 K R  
f 2 , 22 , 0
V  L V  LV
R  K  
2 2 = 2 , 
LV  V  LV
2 2  K  
R = L V  2 , 
V
  LV

 Problem 4: Using Buckingham  - theorem, show that velocity of fluid through a 

D  
circular orifice is given by V = 2gh   , .
H
 VH 
 Solution: 
We have, f (V, D, H, , , g) = 0
-1 -1 -1 -3
V = LT , D = L, H = L,  = L MT ,  = ML , g =
-2
LT n = 6
m=3
 Number of  terms = (6 – 3) =
3 Let H, g and  be repeating variables
a1 b1 c1
1 = H g  V
o o o a1 -2 b1 -3 c1 -1
[L M T ] = [L] [LT ] [ML ] [LT ]
c +b1-3c +1 c -2b -1
[LoMoTo] = [L] 1 1 [M] 1 [T] 1
-2b1 = 1
smartworlD.asia
1
b1 =  2
c1 = 0
a1 + b1 – 3c1 + 1 = 0
1
a1  –0+1=0
2
1
a1 = 
2
1 1 o
1 = H 2 g 2   V
V
1 =
gH
a2 b2 c2
2 = H g  D
o o o a2 -2 b2 -3 c2
[L M T ] = [L] [LT ] [ML ] [L]
a b 3c +1 c -2b
[LoMoTo] = [L] 2+ 2- 2 [M] 2 [T] 2
– 2b2 = 0

b2 = 0
c2 = 0
a2 + b2 – 3c2 + 1 =
0 a2 = –1
-1 o o
2 = H  g   D
H
2 =
D
a3 b3 c3
3 = H g  
o o o a3 -2 b3 -3 c3 -1 -1
[M L T ] = [L] [LT ] [ML ] [L MT ]
c +1 a b c -1
[MoLoTo] = [M] 3 [L] 3+ 3-3 3
-2b -1
[T] 3 c3 = – 1
1
b3 = – 2
1
a3 – +3–1=0
smartworlD.asia
2
3
c3 = –
2
3 1 -1
3 = H 2 g 2  
3 = 
3
 gH
3 = 
 gH.H
f (1, 2, 3) = 0
 V H  
f , ,  =0
 gh D  gH  H

 
V H  
=  , 
 
gH D  gH  H 
D  
v= 2gH  

, 

H
 VH 
7

 Problem 5: Using dimensional analysis, derive an expression for thrust P

developed by a propeller assuming that it depends on angular velocity , speed
of advance V, diameter D, dynamic viscosity , mass density , elasticity of the
fluid medium which can be denoted by speed of sound in the medium C. 


 Solution: 
-2
f (P, , V, D, , , C) = P = LMT
o o -1
0n=7 =L M T
o -1
m=3 V = LM T
D=L
Taking D, V and  as repeating variables.
-1 -1
 = L MT
-3
a b c  = ML
1 V 1
1 = D 1  P
-1
C = LT
o o o a1 -1 b1 -3 c1 -2
[L M T ] = [L] [LT ] [ML ] [LMT ]
c b -3c +1 c +1 -b -2
[LoMoTo] = [L] 1+ 1 1 [M] 1 [T] 1
smartworlD.asia
– b1 –2 =
0 b1 = –2
c1 +1 = 0
c1 = –1
a1 + b1 – 3c1 + 1 =
0 a1 – 2 + 3 + 1 = 0
a1 = –2
-2 -2 -1
1 = D  V   P
P
1 = 2 2
D V
a2 b2 c2
2 = D V  
o o o a2 -2 b2 -3 c2 -1
[L M T ] = [L] [LT ] [ML ] [T ]
a b -3c c -b -1
[LoMoTo] = [L] 2+ 2 2 [M] 2 [T] 2
– b2 – 1 =
0 b2 = – 1
c2 = 0

a2 – 1 + 0 =
0 a2 = –1
1 -1 o
2 = D  V  
D
2 = V
a3 b3 c3
3 = D V  
o o o a3 -1 b3 -3 c3 -1 -1
[M L T ] = [L] [LT ] [ML ] [L MT ]
a b -3c -1 c +1 b -1
[MoLoTo] = [L] 3+ 3 3 [M] 3 [T]- 3
b3 = – 1
c3 – 1 + 3 - 1 =
0 c3 = – 1
-1 -1 -1
3 = D  V  

3 = 
VD
smartworlD.asia
4 = D
o o o
a4
V
b4
a4

c4
C
-1 b4 -3 c4 -1
M L T = [L] [LT ] [ML ] [LT ]
a b -3c +1 c -b -1
MoLoTo = [L] 4- 4 4 [M] 4 [T] 4
b4 = –
1 c4 = 0
a4 – 1 + 0 + 1 =
0 a4 = 0
o -1 o
4 = D  V   C
C
4 =
V
f (1, 2, 3, 4) = 0
 P D C 
f , , , 0
 2 2 
 DV  V VD V 
2 2 D  C
P=DV  , , 
 
 V VD V 
9

 Problem 6: The pressure drop P in a pipe depends on mean velocity of flow V,

length of pipe l, viscosity of the fluid , diameter D, height of roughness
projection K and mass density of the liquid . Using Buckingham’s method
obtain an expression for P. 


 Solution: 
-1 -2
f (P, V, l, , D, K, ) = 0 P = L MT
o -1
n=7 V = LM T
o o
 number of  terms = 7 – 3 = 4 l = LM T
-1 -1
 = L MT
o o
Let D, V,  be the repeating variables K = LM T
-3
1 = D
a1
V
b1

c1
P  = ML
o o o a1 -1 b1 -3 c1 -1 -2
[L M T ] = [L] [LT ] [ML ] [L MT ]
[LoMoTo] = [L]a1+b1-3c1-1 [Mc1+1] [T-b1-2]

-b1 – 2 =
0 b1 = - 2
c1 = - 1
smartworlD.asia
a1 + b1 – 3c1 – 1 =
0 a1 – 2 + 3 – 1 =
0 a1 = 0
o -2 -1
1 = D  V 
 P
P 1 = V 2 
a2 b2 c2
2 = D V  l
o o o a2 -1 b2 -3 c2
[L M T ] = [L] [LT ] [ML ] [L]
[LoMoTo] = [L]a2+b2-3c2+1 [M]c2 [T] –b2
b2 = 0
c2 = 0
a2 + 0 + 0 + 1 =
0 a2 = – 1
10

-1 o o
2 = D  V  
l
L 2 = D
a3 b3 c3
3 = D V  K
o o o a3 -1 b3 -3 c3
[L M T ] = [L] [LT ] [ML ] [L]
[LoMoTo] = [L]a3+b3-3c3+1 [M]c3 [T] –b3
b3 = 0
c3 = 0
a3 + b3 – 3c3 + 1 =
0 a3 = – 1
K
3 = D
a4 b4 c4
4 = D V  
o o o a4 -1 b4 -3 c4 -1 -1
[L M T ] = [L] [LT ] [ML ] [L MT ]
smartworlD.asia
[LoMoTo] = [L]a4+b4-3c4-1 [M]c4+1 [T] –b4-1
b4 = –1
c4 = –1
a4 + b4 – 3c4 – 1 =
0 a4 – 1 + 3 – 1 =
0 a4 = –1
-1 -1 -1
4 = D  V  
4 = 
VD
 P l K  
f , , ,  =0
 2 
V
 D D VD 

P V   L K  
2
 , , 
 
D
 D VD 
11

MODEL ANALYSIS
Session – IX
Before constructing or manufacturing hydraulics structures or hydraulics

machines tests are performed on their models to obtain desired information about
their performance. Models are small scale replica of actual structure or machine. The
actual structure is called prototype.
 Similitude / Similarity 

It is defined as the similarity between the prototype and it’s model.
 Types of Similarity 

There are three types of similarity.
o Geometric similarity
o Kinematic similarity
Dynamic similarity
 Geometrical Similarity 

Geometric similarity is said to exist between the model and prototype if the
smartworlD.asia
ratio of corresponding linear dimensions between model and prototype are equal.
i.e. Lp  h p  Hp ............  Lr
L m h m Hm
Lr  scale ratio / linear ratio
Ap  L 2 Vp  L 3
r r
A V
m m
 Kinematic Similarity 
Kinematic similarity exists between prototype and model if quantities such at
velocity and acceleration at corresponding points on model and prototype are same.
 V1  p  V2 p  V3 p ...........  V
V 1  m V 2 m  V 3  m
r
Vr  Velocity ratio
 Dynamic Similarity 

Dynamic similarity is said to exist between model and prototype if ratio of
forces at corresponding points of model and prototype is constant.
 F1  p
 F2 p  F3 p ...........  F
F 1 m
 F 2  m  F3  m R
FR Force ratio

 Dimensionless Numbers 
Following dimensionless numbers are used in fluid mechanics.
1. Reynold’s number
2. Froude’s number
3. Euler’s number
4. Weber’s number
5. Mach number
1. Reynold’s number
It is defined as the ratio of inertia force of the fluid to viscous force.
Fi
 NRe 
F
v
Expression for NRe
Fi = Mass x Acceleration
Fi =  x Volume x Acceleration
smartworlD.asia
Fi =  x Volume x Change in velocity
Time
Fi =  x Q x V
2
Fi = AV
FV  Viscous force
FV =  x A
V
FV =  A
y
V
FV =  A
L
2
NRe = AV
V
 A
L
VL
NRe = 
In case of pipeline diameter is the linear dimension.
NRe = VD


2. Froude’s Number (Fr)

It is defined as the ratio of square root of inertia force to gravity force.
Fr = Fi
F
g
Fi = m x a
Fi =  x Volume x Acceleration
2
Fi = AV
Fg = m x g
Fg =  x Volume x g
Fg =  x A x L x g
2
AV
F =
xAxLxg
2
V
smartworlD.asia
F =
Lg
F = V
Lg
3. Euler’s Number (u)

It is defined as the square root of ratio of inertia force to pressure force.
u = Fi
Fp
Fi = Mass x Acceleration
Velocity
Fi =  x Volume x
Time
Fi =  x Q x
2
V Fi = AV
Fp = p x A
2
AV 
u = V
pA p

u = v
p

4. Weber’s Number (Wb)

It is defined as the square root of ratio of inertia force to surface tensile force.
F
i
Wb =
Fp
2
Fb = AV
Fs =  x L
2
AV L
Wb = V
L 
V
Wb =

L
smartworlD.asia
5. Mach Number (M)
It is defined as the square root of ratio of inertia force to elastic force.
M= Fi
F
e
2
Fi = AV
Fe = K x A
K  Bulk modulus of elasticity
A  Area
2
AV
M=
KA
V
M=
K/
V
M=C
C  Velocity of sound in fluid.

MODEL LAWS (SIMILARITY LAWS)
1. Reynold’s Model Law

For the flows where in addition to inertia force, similarity of flow in model
and predominant force, similarity of flow in model and prototype can be established
if Re is same for both the system.
This is known as Reynold’s Model Law.
Re for model = Re for prototype
(NRe)m = (NRe)p
 VD  VD 
   
   
  m   p
m  V m  Dm
p  Vp  Dp
=1
m
p

r  Vr  Dr  1
r
smartworlD.asia
Applications:
i) In flow of incompressible fluids in closed pipes.
ii) Motion of submarine completely under water.
iii) Motion of air-planes.
2. Froude’s Model Law

When the force of gravity is predominant in addition to inertia force then
similarity can be established by Froude’s number. This is known as Froude’s model
law.
(Fr)m = (Fr)p
   V 
 V   
   
gL
  m 
gL
p
 
 V  =1
 

gL
r
Applications:
Flow over spillways.
Channels, rivers (free surface flows).
Waves on surface.
Flow of different density fluids one above the other.

MODEL ANALYSIS
Session – X
3. Euler’s Model Law

When pressure force is predominant in addition to inertia
force, similarity can be established by equating Euler number of
model and prototype. This is called Euler’s model law.
(u)m = (u)p
   
   
 V   Vp 
 
m
 
 pm   pp 
 
 m  p
Application: Turbulent flow in pipeline where viscous force and
smartworlD.asia
surface tensile forces are entirely absent.

4. Mach Model Law

In places where elastic forces are significant in addition to
inertia, similarity can be achieved by equating Mach numbers for
both the system.
This is known as Mach model law.
Mm = M
     
   V   V 
 V   p    
K  K    1
m
 
 m   p   K 
    
 m  p 
 
Applications:
22. Aerodynamic testing where velocity exceeds speed of
sound.
23.
smartworlD.asia
Eg: Flow of airplane at supersonic speed.
Water hammer problems.

5. Weber’s Model Law:

If surface tension forces are predominant with inertia force,
similarity can be established by equating Weber number of model
and prototype.
Wm = W 
   
 V   V 
   
     
L
 m L
p
  
 V 
  1
  
L
  r
smartworlD.asia

Applications:
(xxi) Flow over wires with low heads.
(xxii) Flow of very thin sheet of liquid over a surface.
(xxiii) Capillary flows.
smartworlD.asia

 Problem 1: A pipe of diameter 1.5 m is required to transmit

-2
an oil of S = 0.9 and viscosity 3 x 10 poise at 3000 lps. Tests
o
were conducted on 15 cm diameter pipe using water at 20 C.
o
Find velocity and rate of flow of model if  water at 20 C is 0.01
poise.
smartworlD.asia

 Solution
Dp = 1.5 m
Sp = 0.9
-2 -3 2
p = 3 x 10 poise = 3 x 10 Ns/m
-3 3 3
Qp = 3000 lps = 3000 x 10 m /s = 3 m /s
Dm = 0.15
m Sm = 1
Vm = ?
Qm = ?
Ap Vp = Qp
Vp = 1.698 m/s
m = 0.01 poise
= 0.001 poise
3
m = 1000 kg/m
3
p = 0.9 x 1000 = 900 kg/m
smartworlD.asia

(Re)m = (Re)p Dp = 1.5 m

Sp = 0.9
m V D m
p V p D p p = 3 x 10 -2 poise
=3x

-3 2
m
m p 10 Ns/m
Qp = 3000 lps = 3000 x
-3 3 3
1000 x Vm x 0.15
 900 x 1.698 x 1.5
10 m /s = 3 m /s
Dm = 0.15 m
0.001 3 x 10 3 Sm = 1
Vm = ?
Vm = 5.094 m/s Qm = ?
A p V p = Qp
Q = AmVm Vp = 1.698 m/s
m = 0.01 poise
Q =  0.15 5.094
2
= 0.001 poise
3
4 m = 1000 kg/m
3 3
Q = 0.09 m /s p = 0.9 x 1000 = 900 kg/m
Q = 90 lps.
smartworlD.asia

 Problem 2: In a 1 in 40 model of spillway velocity and

3
discharge are 2 m/s and 2.5 m /s. Find the corresponding
velocity and discharge in prototype.
smartworlD.asia

 Solution
Since it is a spillway problem, L 1
Froude’s law of similarity is used.
L = m 
Lp 40
(F)m = (F)p Vm = 2 m/s
3
 V  V  Qm = 2.5 m /s
   
  
gL 
 gL m  p
2 Vp
9.81 x 1  9.81 x 40
Vp = 12.65 m/s
smartworlD.asia

For a spillway,
2.5
QL
2.5
Qp  Lp
2.5
Qm Lm
Qp
2.5  40
2.5
3
Qp = 25298.22 m /s
smartworlD.asia
10

 Problem 3: Experiments area to be conducted on a model

ball which is twice as large as actual golf ball. For dynamic
similarity, find ratio of initial velocity of model to that of actual
ball. Take fluid in both cases as air at STP.
It is a case of motion of fully submerged body.
 Reynolds’s number of flow determines dynamic similarity.
smartworlD.asia
11

 Solution
 (Re)m = (Re)p V m  dm = V p  dp
m =  p V dp
m 
m = p Vp dm
    V 1
 Vd   Vd  m 
  m   p Vp 2
dm Vm = 0.5 Vp
2
dp
smartworlD.asia
12

 Problem 4: o
Water at 15 C flows at 4 m/s in a 150 mm
o
diameter pipe. At what velocity oil at 30 C must flow in a 75 mm
diameter pipe for the flows to be dynamically similar? Take

o -6 2
kinematic viscosity of water at 15 C as 1.145 x 10 m /s and
o -6 2
that for oil at 30 C as 3 x 10 m /s.
smartworlD.asia
13

 Solution
Vp = 4 m/s  Vd   Vd 
   
dp = 0.15 m   m    p
Vm = ? Vm x 0.075 4 x 0.15
6 6
Dm = 0.075 m 3 x 10  1.145 x 10
  6 2
   1.145 x 10 m /s Vm = 20.96 m/s
 p
  6 2
   3 x 10 m /s
 m
smartworlD.asia
14

 Problem 5: A model with linear scale ratio (model to
prototype) x, of a mach 2 supersonic aircraft is tested in a wind
tunnel where in pressure is y times the atmospheric pressure.
Determine the speed of model in tunnel given that velocity of
sound m atmospheric air is Z.
smartworlD.asia
15

 Solution
L
m x C=Z
Lp V
2
M=2 C
Pm = y patm V 2
Z
m = y atm Vp = 2Z
smartworlD.asia
16

Dynamic similarity in this case is established by Reynold’s Model

law.
(Re)m = (Re)p
 VL   VL 
   
 m   p
y
 xV xL
atm m m 
p x V p x L p
m p

y atm  Vm  x  atm  2Z
m 1 p
2 Z
Vm = xy
smartworlD.asia
17

Surge Tank
Surge is the instantaneous rise in pressure due to sudden partial or complete closure of
valve on the downstream end of a long pipeline. Surge tanks are generally built as a part
of hydroelectric plant. In a long pipeline (Penstock), conveying water from a reservoir to
the turbines, there will be sudden fluctuations in the discharge at the outlet of the pipeline
with the varying load on the generator coupled to the turbine. There will be need for the
generator speed to be cut down suddenly due to decrease in load which in turn decreases
the discharge. This affects over a long pipeline instantaneously increasing the pressure at
the outlet, thereby bursting the pipe. If there is an open tank whose level is kept well
above the supply reservoir, located closer to the outlet, it can temporarily accommodate
the additional supply of water coming from both the reservoir and the backwater from
the control valve.
Similarly, there will be need for the generator speed to be increased suddenly due to
smartworlD.asia
increase in the load which in turn increases the discharge. This additional supply of
discharge which has to be obtained from the reservoir in turn immediately increases the
flow velocity in the pipeline thereby decreasing the pressure. This results in crushing of t
he pipe as the external pressure is far more than the internal pressure. The surge tank if
provided can augment the supply of water due to sudden increase in discharge
temporarily and prevent the damage to the pipeline.
The surge tank is an open topped large chamber provided so as to communicate freely
with the pipe line bringing water from the reservoir. The upper lip of the surge tank is
situated at a suitable height above the maximum water level in the reservoir. When the
turbine is working under steady load and the flow through the pipe is uniform there will
be a normal pressure gradient OE. The water level in the surge tank will be lower than
that in the reservoir by GE which represents the loss of head in the pipe line due to
friction . If now the rate of flow in the pipe line is suddenly decreased, there will be a
sudden pressure rise and this will result in a

sudden rise in the water level in the surge tank so that the hydraulic gradient is now
along OF . In this situation, the water level in the surge tank will be higher than that in
the reservoir. This condition prevails only for a short duration. The surge tank acts as an
auxiliary storage reservoir
Normal
HGL for
rapidly F
O G
E
Surge
HGL for D
increased
A B Penstoc
smartworlD.asia SURGE TANK

C
to collect the flow down the pipe when the flow through the pipe is reduced or stopped .
The excess water is accumulated in the surge tank. This arrangement eliminates the
instantaneous expansion of the pipe line and thus prevents pipe bursting. Similarly, due
to increased flow condition during excess of water requirement will result in a sudden
decrease in the water level in the surge tank so that the hydraulic gradient is now along
OD .
Other Types of Surge Tanks, Besides the simple cylindrical surge tank, other types
are also adopted.
(i) Conical surge tank (ii) Surge tank with internal bell -mouthed spillway
(iii) Differential surge tank
Fig. a shows a conical surge tank which is similar to the simple surge tank described
earlier, except in this case the tank has a conical shape.

Fig. b shows a surge tank provided with internal bell -mouthed spill way. This
arrangement allows the overflow to be conveniently disposed of.
Fig. c shows a differential surge tank. This has the advantage that for the same stabilising
effect its size can be very much less than that of the ordinary surge tank . Inside the surge
tank there is a riser pipe provided with ports at its bottom. When there is an increase in
pressure in the pipe, some small quantity of water enters the surge tank through these
ports but the major bulk of the incoming flow mounts to the top of the riser and th en
spills over into the tank . Thus this provides a substantial retarding head while in the
ordinary surge tank the head only builds up gradually as the tank gets filled - It may
further be realized that the water is not allowed to waste in the differential tank
smartworlD.asia
(b) Surge tank with internal
(a) Conical Surge tank
bell-mouthed spillway
Riser
Ports
(c) Differential Surge tank

Unit Quantities
In the studies of comparison of the performances of turbines of different output, speeds
and different heads, it is convenient to determine the output, the speed and the discharge,
when the head on the turbine is reduced to unit y, i . e . 1 m . The conditions of the
turbine under unit head are such that the efficiency of the turbine remains unaffected .
Thus the velocit y triangles under working conditions and under unit head are
geometricall y similar.
Given a turbine every velocit y vector ( V 1 , U 1 , Vw 1 , V f 1 ) is a function of H

where H is the head on the turbine. With this basic concept, we can determine the speed,
discharge and power under unit head .
Unit Speed ( Nu ):
This is the speed of a turbine working under a unit head
Let N be the speed of turbine, H be the head on the turbine and u be the peripheral velocit
y.
We know that the peripheral velocit y u is given b y
u
D N
smartworlD.asia
where D is the mean diameter of the runner which is treated as 60
constant and N is the speed of the runner, Hence

uN
But u  K u 2 H and hence u  H
Hence N  H
i . e . N K1 H , where K 1 is the proportionalit y constant .

From definition of Unit speed, it is the speed of a turbine when working
under unit head . Hence at H=1 , N=N u . Substituting, we get
N u K1 1
N
N Nu H or Nu  (01)
H
Unit Discharge ( Qu ) :
This is the discharge through the turbine working under a unit head

Consider the Q as the discharge through a turbine. From discharge continuit y equation,
Q = a x V , where a is the cross -sectional area of flow and V is the mean flow velocit y.
For a given turbine, the cross - sectional area is constant and hence Q  V
But V  Cv 2g H and hence V  H and hence Q H
i . e . , Q K 2 H where K 2 is the proportionalit y constant .

From definition of Unit discharge, it is the discharge through the turbine
when working under unit head . Hence at H=1 , Q=Q u . Substituting, we get
Qu K 2 1
Q
Q Qu H or Qu  (02)
H
Unit Power (P u ) :
This is the Power developed b y the turbine working under a unit head Consider
the P as the power developed by the turbine.
We know that the efficiency of turbine is given b y
 P
QH smartworlD.asia
Where  is the weight densit y of the fluid/water passing through the turbine, Q is the
discharge through the turbine and H is the head under which the turbine is working . But
efficiency of a turbine and weight densit y of water are constants and hence, we can write
PQH
From discharge continuit y equation, Q = a x V , where a is the cross - sectional area of
flow and V is the mean flow velocit y.
For a given turbine, the cross - sectional area is constant and hence Q  V
But V  Cv 2g H and hence V  H and hence Q H

Substituting, we get
P  H H or P K 3 H H
where K 3 is the proportionalit y constant .

From definition of Unit Power, it is the power developed b y the turbine when working
under unit head . Hence at H=1 , P=P u . Substituting, we get
Pu K 3 1 1
P P
P Pu H H or Pu   3 (03)
2
H H H
Unit Speed, Unit discharge and Unit Power is definite characteristics of a turbine.
If for a given turbine under heads H 1 , H 2 , H 3 ,…. the corresponding speeds are N 1 , N
2 , N 3 ,…, the corresponding discharges are Q 1 , Q 2 , Q 3 ,…. and the powers developed
are P 1 , P 2 , P 3 ,…. Then
N
Unit speed = N  N1  N 2  3
u
H1 H2 H3
Unit Discharge = Q  Q1  Q2  Q3
u
H H H
1 2 3
Unit Power = P  P1  P2  P3 or P  P1  P2  P3
smartworlD.asia
u u 3 3 3
2 2 2
H H1 H H2 H H 3 H1 H2 H3
Thus if speed, discharge and power developed b y a turbine under a certain head are
known, the corresponding quantities for an y other head can be determined .
Specific Speed of a Turbine (N s )

The specific speed of a turbine is the speed at which the turbine will run when
developing unit power under a unit head . This is the t ype characteristics of a turbine .
For a set of geometricall y similar turbines the specific speed will have the same value.
Consider the P as the power developed by the turbine. We know

that the efficiency of turbine is given b y
P

QH
Where  is the weight densit y of the fluid/water passing through the turbine, Q is the
discharge through the turbine and H is the head under

which the turbine is working . But efficiency of a turbine and weight densit y of water are
constants and hence, we can write
b
D
smartworlD.asia b
D
PQH
Discharge is given by the product of cross sectional area of flow and the flow velocit y.
Cross sectional area is  d b and hence
Q=DbVf
But V  Cv 2g H and hence V  H
And u  K u 2 H and hence u  H

Further, the peripheral velocit y is given by
D N
u where D is the mean diameter of the runner . 60
From the above two equations of u , we can write that

DN  H
H
or D
N
But in turbines the width of flow area b is proportional to the diameter D . Hence D  b,
with which
H
b
N
H H
Hence P  H
N N
5
H 2
or P
N2
5 5
2 H 2 H 2
or N  K
P P
Simplifying further
5
H4
N K
smartworlD.asia
P
But from the definition of specific speed, it is the speed of a turbine when it is working
under unit head developing unit power. Hence when H = 1 and P = 1 . N = N s . Hence
154
N s K and K  N s
1
Substituting we get
H 54
NNs
P
N P
or N s  5
4
H
Examination questions
Dec/Jan 07
Define unit power, unit speed, unit discharge and specific speed with reference to h
ydraulic turbines . Derive expressions for these terms . (06)

July 06
Derive expressions for specific speed of a turbine (06)
A turbine is to operate under a head of 25 m at 200 rpm . The discharge is
3
9 m /s . If the efficiency is 90 %, determine :
i) Power generated ii) Speed and Power at a head of 20 m . (07)
Jan 06
What is specific speed of a turbine and ex plain its significance (04)
Jan 05
Define and derive an expression for specific speed of a turbine, indicating
its significance. (08)
Define the terms unit power, unit speed and unit discharge with reference
to a h ydraulic turbine. Also give the expressions for these terms (06)
July 04
Define specific speed of a h ydraulic turbine . Derive an equation for
specific speed in terms of operating speed, power and head (08)
smartworlD.asia

Dec/Jan 07
Suggest a suitable type of a turbine to develop 7000 kW power under a head of 20 m,
while operating at 220 rpm . What are the considerations fo r your suggestion? (04)
Solution:
P = 7000 kW; H = 20 m; N = 220 rpm .
We know that speci fic speed of a turbine is given b y
Ns  N P
5
H4
N s  220 7000 435 rpm

5
4
20
As the specific speed is between 300 and 1000, Kaplan turbine can be suggested .
Jan 06
smartworlD.asia
3
A turbine is to operate under a head of 25 m at 200 rpm . The disc harge is 9 m /s . If
the efficiency is 90%, determine the performance of the turbin e
under a head of 20 m (08)
Solution:
3
H 1 = 25 m; N 1 = 200 rpm; Q = 9 m /s;  = 0 . 90, H 2 = 20 m; N 2 = ?; Q 2 = ?
P 1 = ?, P 2 = ?
We know that
P

QH
P
0.9   
10 1000 9 25
P 1 = 2025 kW
N N
Unit speed = N  1
 2
u
H H
1 2

Unit Discharge = Q  Q1  Q2
u
H1 H2
u 3 3
2
H1 H2 2
N  200  N 2  40
u
25 20
N 2 = 178 . 9 rpm(Ans)
Q  9  Q2 1.8
u
25 20
3
Q 2 = 8 . 05 m /s (Ans)
P  2025
3
 P23 16.2
u
2 2
25 20
P 2 = 1449 kW (Ans)
July 04
Suggest a suitable type of turbine to develop 7500 kW of power under a head of 25 m,
smartworlD.asia
while operating at 220 rpm . If the same turbine has to work under a head of 10 m, what
power would devel op? What would be the new
speed? (12)
Solution:
P 1 = 7500 kW; H 1 = 25 m; N 1 = 220 rpm; H 2 = 10 ; P 2 = ? ; N 2 = ? We
know that specific speed of a turbine is given b y
N P
Ns  5
4
H
s
 220 7500 
N 340.8 rpm
5
4
25
As the specific speed is between 300 and 1000, Kaplan turbine can be suggested .

Unit speed = N u  N1  N 2
H1 H2
u 3 3
2 2
H1 H2
N u  220  N 2  44
25 10
N 2 = 139 . 14 (Ans)
P  7500  P23  60
u 3
2 2
25 10
P 2 = 1897 . 4 kW (Ans)
smartworlD.asia
Dr . M . N . S he sha Pra ka sh , Pro f e sso r, J . N . N . C o lleg e o f E ng i nee ri ng , Sh i mo g a 9

HHM-Notes 2 PDF

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

HHM-Notes 2 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

HHM-Notes 2 PDF

Uploaded by

Copyright:

Available Formats

Smartworld.asia Specworld.

Department of Civil Engineering

Governors for Turbines

Fig . shows a general layout of a h ydroelectric plant .

Animation as in the PPT

It consists of the following:

7. Mechanical Efficiency: (m)

If S . P . is the Shaft Power

(iii) Overall Efficiency: ( )

Turbine Type of Direction Specific

PELTON WHEEL OR TURBINE

(iv) Breaking jet:

Velocit y triangles for the jet striking the bucket

F x = (Mass of water / second) x change in velocit y along the x direction

  aV1 Vw1 Vw2  

Efficiency of the jet = Output / sec ond  Workdone / sec ond

Fx   aV1 V1 u 1 Cos

Substituting these values in the above equation for efficiency, we have

  2u V1  V12 u cos u

V  Cv 2 g H  0.97 2 10 640 109.74 m/s

Let the bucket speed be u

N  60 u  6049.48  787.5 rpm (Ans)

Jet ratio = m = u  49.48  0.45

H ydraulic Efficiency =   Work done/s  4679.82 100  90.17%

V  Cv 2 g H  0.98 2 10 1000 43.83 m/s

V  Cv 2 g H  0.98 2 10 700 115.96 m/s

  2 u V u 1 cos 2 52.36

V  Cv 2 g H  0.98 2 10 30 24 m/s

1  aV 3  1  QV 2  1 1000 0.7 242  201.6 kN -m/s

  2 u V u 1 cos2 210 24 101 cos 20 94.29% (Ans)

iv) the number of Jets required .

V  Cv 2 g H  0.97 2 10 800 122.696 m/s

u  2 g H  0.46 210800  58.186 m/s

D  60 u  6058.186 1.85 m (Ans)

d  1.85 115 . 625 mm (Ans)

No . of jets = n  Q  1.947  2 (Ans)

Absolute velocit y of vane is given b y u 

Jet Ratio = m  D  1.22 16.32

V  Cv 2 g H  0.98 2 10 450 92.97 m/s

Jet Ratio = m  D  1.22 16.32

V  Cv 2 g H  0.97 2 10 60  33.6 m/s

u  Ku 2 g H  0.46 210 60 15.93 m/s

The following data is related to a Pelton wheel:

 H g  hf  0.91  250  hf

Net head on the turbine = H = Hg  hf = 227.5 m

Velocity of jet = V1  Cv 2 g H  0.975 2 10 227.5  65.77 m/s

Vr1 = (V1u1)=87.6541.14 = 46.51 m/s

Fx = 1000 x 1.042 (87.65+1.53) = 92.926 kN (Ans)

The main types of reaction turbines are

Guide vanes: Already mentioned in the above sections.

Francis Turbine Cross -

Hydraulics and Hy draulic Machines

Derivation of the efficiency of a reaction turbine

Tangential speed of the vane at outlet = u 2 =  R 2

=  a V 1 x V w 1 (V w 1 is the velocit y component of flow at inlet along tangential

=  a V 1 x (V w 2 ) ( V w 2 is the velocit y component of flow at outlet along

component is acting in the opposite direction)

V u  velocit y of whirl at outlet is to be substituted as along