A

Seminar report

On
Automatic Sun Tracking System (ASTS)
Submitted in partial fulfillment of the requirement for the award of degree
of Electronics

SUBMITTED TO: SUBMITTED B

 Preface
I have made this report file on the topic Automatic Sun Tracking System (ASTS; I have tried
my best to elucidate all the relevant detail to the topic to be included in the report. While in the
beginning I have tried to give a general view about this topic.

My efforts and wholehearted co-corporation of each and everyone has ended on a successful note.
I express my sincere gratitude to …………..who assisting me throughout the preparation of this
topic. I thank him for providing me the reinforcement, confidence and most importantly the track
for the topic whenever I needed it.
 Acknowledgement
I would like to thank our respected … and … for giving me such a wonderful opportunity to
expand my knowledge for my own branch and giving me guidelines to present a seminar report. It
helped me a lot to realize of what we study for.

Secondly, I would like to thank my parents who patiently helped me as i went through my work
and helped to modify and eliminate some of the irrelevant or unnecessary stuffs.

Thirdly, I would like to thank my friends who helped me to make my work more organized and
well-stacked till the end.

Next, I would thank Microsoft for developing such a wonderful tool like MS Word. It helped my
work a lot to remain error-free.

Last but clearly not the least, I would thank The Almighty for giving me strength to complete my
report on time.
 :
CONTENTS

o INTRODUCTION
o STRUCTURE OF ASTS
 Motor selection
 Solar sensor
o WORKING OF ASTS
 Basic principle
 Sun tracking sensors(STS)
 Night time fault detector(NTFD)
 Day time fault detector(DTFD)
 Night and Cloud detection
o CONTROL STRATEGY OF ASTS
 Automatic control
 Manual control
o CONCLUSION
o REFERENCES
 Automatic Sun Tracking System (ASTS)
INTRODUCTION:

In remote areas the sun is a cheap source of electricity because instead of hydraulic
generators it uses solar cells to produce electricity. While the output of solar cells depends on the
intensity of sunlight and the angle of incidence. It means to get maximum efficiency; the solar
panels1 must remain in front of sun during the whole day. But due to rotation of earth those
panels can’t maintain their position always in front of sun. This problem results in decrease of
their efficiency. Thus to get a constant output, an automated system is required which should be
capable to constantly rotate the solar panel. The Automatic Sun Tracking System (ASTS) was
made as a prototype to solve the problem, mentioned above. It is completely automatic and keeps
the panel in front of sun until that is visible. The unique feature of this system is that instead of
taking the earth as its reference, it takes the sun as a guiding source. Its active sensors constantly
monitor the sunlight and rotate the panel towards the direction where the intensity of sunlight is
maximum. In case the sun gets invisible e.g. in cloudy weather, then without tracking the sun the
ASTS keeps rotating the solar panel in opposite direction to the rotation of earth. But its speed of
rotation is same as that of earth’s rotation2. Due to this property when after some time e.g. half an
hour when the sun again gets visible, the solar panel is exactly in front of sun. Moreover the
system can manage the errors and also provides the error messages on the LCD display. In manual
mode, through the software (GUI) at computer, the solar panel can be rotated at any desired angle.

Fig. 1: Automatic Sun Tracking System—Dishes and PV.

 Fig. 2: Automatic Sun Tracking System—Heliostat and Parabolic Trough.

ASTS can be used for Parabolic Trough tracker, Dishes tracker, PV (Photovoltaic
generator) tracker, Heliostat, Solar Furnace and so on. Even though the theory of the controller
system is similar to all the applications, there are some differences: the precision requirement for
dishes tracker is more strict than PV tracker, while the Heliostat and solar furnace need the
strictest precision requirement, and more difficult to apply solar sensor to make a closed-loop
control system. So, when design these systems, selection of motor type, controller type and
tracking mode should be different.

STRUCTURE OF ASTS:
ASTS is a hybrid hardware/software project. Its general structural diagram is shown in figure-3.

The software includes:

• VB 6.0 based GUI.
• Microsoft Access Database.
• Embedded Software (written in C) for microcontroller AT89c52.

The hardware includes:

• Solar panel assembly structure containing six functional sensors, stepper motor and solar cells.
• System Control Unit containing LCD, Keypad, Error Indicators and Emergency Stop switch.
• Complete PCB containing two microcontrollers (89c52). First one is the “Master
Microcontroller” which controls the automatic operation of ASTS. While second one, the “Slave
Microcontroller” serially communicates (RS232) with VB software in computer.
 Figure3. General Assembly of ASTS

MOTOR SELECTION:

There are many types of motor can be selected in ASTS design. Currently, several types of
motors being used in the area of ASTS around the world are: Step-motor, Servo-motor, AC
asynchronous motor, permanent magnetic DC servo motor, permanent magnetic brushless
synchronous motor, etc.
Generally speaking, as the gear ratio is high for the transmission system, motor control
precision has very small impact to the tracking precision. For example, for a system with the gear
ratio of 20000:1, the tracker only covers an angle of 0.314mrad when a one complete circle is
finished by the motor. Therefore, all kinds of the motor can satisfy the precision of the tracking
system. However the feature of each type of motor is different.

Fig. 4: AC asynchronous motor with encoder

First of all, let’s take a look at the AC asynchronous motor. To use this kind of motor, we
need an encoder to locate the position of the tracker. In our project, we install an encoder at the
end of AC motor. The PLC accepts the pulse to locate the tracker, while the transducer is used to
adjust the tracker’s speed. Certainly, we can install an encoder at the end of the transmission to
ensure the position of the tracker.
The obvious advantage to use AC asynchronous motor is its price. Even though it can
achieve all the needed functions, AC asynchronous motor is too heavy, too large, and too low in
 efficiency to be installed. Also, for this type of motor, the torque at low speed is very small. In
addition to these disadvantages, it needs the work frequency be above 5Hz to function properly.
The lowest work frequency in our project is 10Hz. As such, the possibility for us to use AC
asynchronous motor in the future is eliminated.
Secondly, let’s compare the features of DC Servo-Motor and AC servo-motor.
There are two types of DC servo-motor: motor with brush and motor without
brush. Motor with brush is low in cost, simple in structure, and high in start torque. Also it has
wide range of speed adjustment, is easy to control. Though it needs maintenance from time to time,
it is very convenient to repair (replace the brush). However it produces electro-magnetic interfere.
Motor without brush is small in size, light in weight, high in output, fast in response, small in
inertia, smooth in spinning, stable in output torque, low motor maintenance fee, high in efficiency,
low in electro-magnetic radiation, long life, and can be applied in different working environments.
However it has more complex control system.
AC servo-motor is also a type of motor without brush. There are two types of AC servo-
motor: synchronous AC motor and asynchronous AC motor. Currently, synchronous AC motor is
generally used in movement control. It can cover a wide power range, which could be up to a very
high power level. Nowadays, with the fast development of semiconductor technology, the shift
frequency of power assembly, and the processing speed of micro-computer have been increased
significantly. As such, it is possible to put the AC motor controller into a two-axial coordinate
system to control the directional current components, in order to achieve the performance similar to
the DC motor.

Fourthly, the comparison between AC servo-motor and step motor is done.

AC servo-motor runs smoothly during low speed period; while step-motor is apt to
have low- frequency vibration.
In terms of the frequency-torque Characteristics, the output torque of step-motor decreases
with the increasing of rotation speed. Furthermore the decrease is steep in high-speed range. AC
servo-motor has a comparably stable output torque, when the rotation speed is within the rated
rotation speed. It gives the constant output power when the rotation speed is beyond the rated
value.
Step-motor doesn’t have the overload capability; while AC servo-motor posses a
satisfactory overload capability. The Panasonic AC servo-system is an example: The maximum
Output torque is three times big of the rated output torque, which can be used to overcome the
inertia load during the start period. As the step-motor doesn’t have the overload capability, a
much bigger size of step-motor is needed. Obviously the step-motor will be over-sized during
normal operation.
Controller’s type of Step-motor is open-loop type. It is easy to have the error of “step loss”
 or blockage when the start frequency is high or the load is heavy. Also it is easy to have the error
of overshoot when it is stopped. So, to make sure the precision of control be achieved, designer
needs to pay more attention to the speed-increase or speed-decrease periods. AC servo-motor
system is a closed-loop system. It is possible for the driver-component to sample the signal from
the motor encoder to complete a “position cycle” and “speed cycle” internally. As such, AC
servo-motor system generally will not have the errors of “step loss” or “overshooting”, and is
more reliable in terms of controlling performance.
Step-motor needs 200 to 400 mil-seconds to accelerate from still to a typical
working speed of several hundred rpm. AC servo-motor is better in terms of acceleration
performance. For example, Panasonic MSMA 400W needs only a few mil-seconds to accelerate
from still to its rated speed of 3000RPM. So it is clear that step-motor’s performance is not so
good. However it’s cheaper. Started from late 70s and early 80s, with the development of micro-
process technology, high-power, high-performance semiconductor technology, and manufacturing
technology of permanent magnetic material, the performance price ratio of AC servo-system has
been improved significantly. Price of AC servo-system also is gradually deceasing in recent years.
AC servo motor is becoming the dominant product.

The conclusion is that all the motors, step-motor, AC asynchronous motor, DC motor
with/without brush, AC servo-motor, can be applied in ASTS. Asynchronous AC motor is the
cheapest. But it is big in size, and low in technical specification. The step-motor has a simple
controlling mode and is also low in price. AC servo-motor has the best performance and wide
power range. Its price is also the highest. As for the performance and price for permanent
magnetic DC brushless motor, they are both rated between step-motor and AC servo-motor. Its
performance is close to servomotor. For the situations that the output torque is not very high (less
than 2 NM ), permanent magnetic DC brushless motor is a good option.

SOLAR SENSOR:

Dish type tracking controller and PV tracking controller can be both applied as four-
quadrants solar sensor to correct tracking bias. It is known that solar sensor will lose its
functionality temporally when it’s cloudy. In the area of solar thermal generation, solar sensor
system usually follows the equation based on the astronomic formula to locate the position of the
sun. When a MPU (micro-processor unit) is applied to calculate the sun’s position, because of its
low process speed and low precision, it’s necessary to include a solar sensor to make a closed
loop system. If the tracking system uses a PC or a high-performance DSP as the controller, the
bias for the calculated sun position will be within one percent of mrad (milliradian), when the
system clock is precisely set (Direct time from GPS is an option). No solar sensor is needed to
track the sun, especially when the slope error and the gear-diastema are all small. Exception
happens when the motor is a step-motor and the output torque is not enough. The situation can
lead to a blockage of the motor (For example, a windy weather), which will fail the tracking
system to track the sun precisely. As such, a closed loop solar sensor is recommended in such

system. There are many kinds of solar sensor. The four- quadrants sensor was used in our project
as shown in Figure 5.

Fig. 5: Four quadrant Sensor

In four quadrant sensor system, the Photovoltaic current will be bigger for the quadrant of
bigger solar facular area, which will indicate whether the sun’s incident ray is parallel with the
axial direction of the sensor, then to adjust the angle by the motor. It should be stressed during the
solar sensor design that the inside wall of the solar sensor needs to be blacken to avoid
misjudgment by the reflection of sunray inside the solar sensor

WORKING OF ASTS:

Basic Principal:

The basic functional blocks of this system are six sensors1, and their operation depends upon the
intensity of light falling on solar panel. All sensors (each with different functionality) send their
output to microcontroller AT89c52. Then the microcontroller executes predefined task in its
software. These sensors are being used with following names and functionality:

Sun Tracking Sensors (STS)

These two sensors are mounted in “V” shape (figure-6) exactly in the middle of the solar panel .
The automatic sun tracking is accomplished according to following 3-step diagram.
 Figure6. Basic Automatic Sun Tracking Operation
• Step-1 shows that when the sun is in front of solar panel, both sensors i.e. STS-1 and STS-2 are
getting same amount of light.
• In step-2, after some time as the earth rotates the solar panel gets repositioned with respect to
sun and STS-1 obtains less amount of light. At this point the LDR i.e. STS-1 sends signal to the
microcontroller (figure 3). Then the controller1 rotates motor, resulting the rotation of solar panel
towards the sun.
• Finally step-3 shows the reorientation of solar panel. The process continues until the end of day.

Figure7. Interface of LDR with Microcontroller

Night Time Fault Detector (NTFD)
In routine work of the system if a general fault2 occurs during nighttime then the next morning it
would not work. So at the next sunrise, this sensor detects whether the solar panel is ready for
tracking or not. As shown in figure-8, the NTFD is mounted in east of the solar panel so in normal
conditions it does not work because it gets lesser intense light (predefined) as compared to the
middle sensors i.e. STS-1 and STS-2, but as the fault arises, it starts working.
Day Time Fault Detector (DTFD)
Except some special conditions e.g. cloudy weather etc, the ASTS is supposed to track the sun the
whole day. If the panel stops rotation then DTFD detects this type of fault. The mounting strategy
of this sensor is same as that of NTFD except that it is mounted in the west.
Night and Cloud Detection
In a cloudy day light intensity is less than a normal day. Similarly during night, light intensity is
far less than a cloudy day. So the night and cloud sensors work on this principle to detect the
event. To sense a smaller change in light intensity cloud sensor is more sensitive than the Night
sensor. In case of Night event, the microcontroller stops all operations of the system and
repositions the solar panel towards east to track the sun for next morning.

CONTROL STRATEGY OF ASTS

For a successful operation, the ASTS has two types of control approach:
• Automatic Control
• Manual Control
Automatic Control
With the help of an efficient algorithm (written in C) only one Master Microcontroller1 is being
used to manage the automatic operation of ASTS. This controller has following functions:
• Senses all of six sensors.
• Drives stepper motor.
• Drives LCD.
• Controls the warning indicators e.g. buzzer, LED’s etc.
• Communicates (by parallel port) with the slave microcontroller. The central driving components
of automatic control are only six sensors. Their operation has been explained on the previous
page.
Manual Control
As no human made system is so perfect so an unpredictable fault may occur in the any system.
That is why a manual control option was also kept in ASTS. While designing this part of control
two objectives were kept in mind:
• The manual control should work efficiently.
• It should be as user friendly as possible. Following two approaches have been used to
accomplish the manual control.
• Stand Alone System Control Unit
• Computer based control unit
Stand Alone System Control Unit
It is a simple user interface, which includes onboard LCD, Keypad, Buzzer and a complete PCB
of the system circuit. The LCD (Hitachi HD44780) displays different messages, which can help
the user in manually operating the system. While the keypad includes keys of Numeric Digits,
Emergency Stop, clock wise rotation and counter clockwise rotation. Using keypad a user can
manually rotate the solar panel by entering angle from 0o to 180o. The angle value is limited to
only 180 values because after sunrise, the earth almost rotates only 180 degrees and then the sun
disappears. The advantage of this unit is that to run the system it does not need computer but its
disadvantage is that at a time it controls only one solar panel. In figure-3 this unit shown in
yellow color, in middle of solar panel and computer terminal.
 Figure 8. Flow Chart showing automatic operation of ASTS
Computer Based Control Unit
This is completely software based control, written in VB 6.0. It incorporates a GUI (figure-10)
and a Database, linked with Microsoft Access. Using this software the computer serially
communicates (RS232) with the ASTS. The Slave microcontroller (89c51) of the system makes
 this communication successful. Due to some fault if the solar panel stops rotating, then with the
help of this software a user can:
• rotate the solar panel manually.
• stop all operations of ASTS (in emergency case)
The database of this system can be used to keep records, which can be retrieved even after a long
time. While saving the new data, the database automatically takes the date and time from the
computer and keeps them saved along with the data, entered by the human being. The advantages
of computer-based control include:
• Facility of Database.
• At a time this software can handle three ASTS systems.
• It has an attracting GUI

Figure 9. VB based GUI of ASTS

CONCLUSION

Although ASTS is a prototype towards a real system, but still its software and hardware
can be used to drive a real and very huge solar panel. A small portable battery can drive its control
circuitry. Therefore by just replacing the sensing instrument, its algorithm and control system can
be used in RADAR and moveable Dish Antennas.
REFERENCE
www.google.com
www.wikipedia.com