Professional Documents
Culture Documents
Micromachining Gorilla Glass
Micromachining Gorilla Glass
030
KEYWORDS
Gorilla Glass, isotropic etching, glass micromachining Table 1: The comparison of different glasses and silicon.
INTRODUCTION
Glass is widely used in MEMS, including packaging,
microfluidics optical and RF applications. Soda lime glass
has been used in fabrication of fluidic microchannels
which are chemically stable and relatively inexpensive
[2,3]. Pyrex 7740 (Borosilicate glass) is the most
commonly used in anodic bonding in packaging thanks to
high heat resistance, similar thermal expansion coefficient
(compared to silicon), high electrical isolation and high
transparency in visible light [1] [4,5]. The material
properties of various glasses are summarized in Table 1 Figure 2: Chemically Strengthened Gorilla Glass
[6,7]. Recently, Gorilla glass, chemically-strengthened
glass, has been commercialized by Corning for
touch-screen applications. Gorilla glass adapts the Traditionally, there are several techniques used in
ion-exchange process to allow potassium ions to diffusion glass micromachining, including mechanical drilling, laser
and to form a compressive stress layer on the glass micromachining, deep reactive ion etching (DRIE) and wet
surfaces. The chemical treatment greatly enhances its etching [8]. Mechanical or ultrasonic drillings typically
mechanical properties, making Gorilla glass immune to generate very rough surfaces and do not offer small
cracks and flaws (Figure 2). While Gorilla glass has many features. DRIE requires expensive equipment and metal
properties attractive to MEMS, including hardness masks to create bombardment of high-energy ions.
(resistance to scratching), high fracture toughness, Initially, we investigated laser micromachining for Gorilla
flexibility and antibacterial resistance. Nevertheless, to the glass using femtosecond lasers with wavelength 532nm.
best of our knowledge, there has been no study in the Laser micromachining has been used for Pyrex, and
micromachining of Gorilla Glass. features can be as small as 10-15 μm. Nevertheless, it has
been found challenging to create microstructures with
Gorilla glass due to its intrinsic high stress, and the
microstructures crack at the sharp edges. Micromachining
of Gorilla glass is isotropic and it prevents creation of sharp
corners. In this paper, the process has been optimized with
an additive of HCl to reduce surface roughness.
EXPERIMENT
Materials: Two different generations of Gorilla glass have
Figure 1: Corning's Gorilla Glass undergoes a 4-point been studied (Gorilla 1 and Gorilla 3). The glasses were cut
978-1-5386-2732-7/17/$31.00 ©2017 IEEE 1218 Transducers 2017, Kaohsiung, TAIWAN, June 18-22, 2017
into small pieces (2cm×2cm) with a dicing saw. The Figure 3: The etching rates for Gorilla glass with various
conventional surface scribing with diamond pens etching solutions based on BOE, HF and HF/HCl.
unfortunately created irregular shapes, and glass broke
uncontrollably. The glass was cleaned using Piranha
solutions (H2SO4: H2O2) for 30mins.
1219
The method that we studied here is not limited to
Gorilla 1 and 3. Several new generation of Gorilla glass are
also commercialized from Corning, including Gorilla glass
4, Gorilla glass SR+ and Gorilla glass 5. It may be worthy
to study wet etching of these new glasses and investigate
their applications in MEMS.
CONCLUSIONS
This paper presents characterizations of wet etching of
a new glass, Gorilla glass. The ratio HF:HCl=8:1 was
found optimal for Gorilla glass in order to achieve fast
etching rate and smooth surfaces. Two different
microstructures were fabricated on Gorilla glass, including
etched-through hole arrays and microcantilever. The
Figure 6: An array of etched-through Gorilla glass mechanical properties of micocantilever made of Gorilla
(thickness 500um). glass was measured. The cantilevers were able to deform
12.26 degrees. The result shows the feasibility to use
Figure 7 shows the set-up of bending test for Gorilla glass in MEMS application.
microcantilevers made of Gorilla glass. Figure 8 shows the
corresponding load and tip deflection. Interestingly, the ACKNOWLEDGEMENTS
cantilevers were able to deform 12.26 degrees without
The device was fabricated using Nano Fabrication
breaking, which was very closed to the observation in the 4
Core (nFab) at Wayne State University. We acknowledge
points bending test (Figure 1). Our results show the
the staff support during the device fabrication. This work
feasibility to use Gorilla glass in MEMS.
was supported by NSF CAREER Award (1055932).
REFERENCES
[1] C. Iliescu, J. Jing, F.E.H. Tay, J. Miao, T. Sun,
“Characterization of masking layers for deep wet
etching of glass in an improved HF/HCl solution”,
Surf. Coat. Technol., 198 (2005), pp. 314–318.
[2] Li X, Abe T, Esashi M. Deep reactive ion etching of
Pyrex glass using SF 6 plasma[J]. Sensors and
actuators A: Physical, 2001, 87(3): 139-145.
[3] Lanford W A, Davis K, Lamarche P, et al. Hydration
of soda-lime glass[J]. Journal of non-crystalline solids,
1979, 33(2): 249-266.
[4] Cozma A, Puers B. Characterization of the
Figure7: The setup for bending testing of microcantilever electrostatic bonding of silicon and Pyrex glass[J].
made of Gorilla glass. Journal of Micromechanics and Microengineering,
1995, 5(2): 98.
[5] Lee D J, Ju B K, Lee Y H, et al. Glass-to-glass anodic
bonding for high vacuum packaging of
microelectronics and its stability[C]//Micro Electro
Mechanical Systems, 2000. MEMS 2000. The
Thirteenth Annual International Conference on. IEEE,
2000: 253-258.
[6] Phillips D C, Sambell R A J, Bowen D H. The
mechanical properties of carbon fibre reinforced Pyrex
glass[J]. Journal of Materials Science, 1972, 7(12):
1454-1464.
[7] Pavelchek E K, Doremus R H. Fracture strength of
soda-lime glass after etching[J]. Journal of Materials
Science, 1974, 9(11): 1803-1808.
[8] C. Iliescu, F.E.H. Tay, Wet etching of glass,
Figure 8: The load vs deformation of microcantilever Semiconductor Conference, 1 (2005), pp. 35-44.
made of Gorilla glass.
1220