MEMBUAT COUNTER 7 SEGMENT DENGAN DUA PUSH BUTTON

I. TUJUAN

Siswa dapat mengetahui tentang counter up dan counter down

Siswa dapat memahami fungsi dan aplikasi counter up dan counter down

Siswa dapat membuat program counter up dan counter down

II. ALAT DAN BAHAN

1. PC
2. Program Arduino IDE
3. Protoboard
4. LED Display 7 Segment
5. Kabel jumper
6. 1 Resistor 330Ω dan 2 Resistor 10kΩ
7. Arduino UNO

III. LANGKAH KERJA

1. Siapkan alat dan bahan

2. Rangkai seperti pada gambar

3. Hubungkan Arduino UNO ke PC, dan buka program Arduino IDE

4. Pastikan Arduino UNO anda telah terhubung dengan software. Pilih tab Tools >> Port (pastikan
sudah anda centang)
5. Masukan program yang berada di bawah kesimpulan, dengan cara copy paste
6. Pilih simbol centang untuk verifikasi kode
 7. Save pada tempat yang anda inginkan
8. Lalu klik simbol anak panah untuk mengupload kode
9. Dan lihat hasilnya

int a = 2;

int b = 3;

int c = 4;

int d = 6;

int dp = 5;

int e = 7;

int f = 8;

int g = 9;

int tb1 = 13;

int tb2 = 12;

int counter = 0;

int buttonUpState = 0;

int lastButtonUpState = 0;

int buttonDownState = 0;

int lastButtonDownState = 0;

void setup(){

Serial.begin(9600);

pinMode(a, OUTPUT);

pinMode(b, OUTPUT);

pinMode(c, OUTPUT);

pinMode(d, OUTPUT);

pinMode(e, OUTPUT);

pinMode(f, OUTPUT);
 pinMode(g, OUTPUT);

pinMode(dp, INPUT);

digitalWrite(dp , LOW);

void loop(){

buttonUpState = digitalRead(tb1);

buttonDownState = digitalRead(tb2);

if (buttonUpState != lastButtonUpState){

if (buttonUpState == HIGH){

if (counter == 9){

counter = -1;

counter++;

Serial.println(counter);

changeNumber(counter);

delay(300);

else{

Serial.println("OFF");

delay(50);

if (buttonDownState != lastButtonDownState){

if (buttonDownState == HIGH){

if (counter == 0){
 counter = 10;

counter--;

Serial.println(counter);

changeNumber(counter);

delay(300);

else{

Serial.println("OFF");

delay(50);

changeNumber(counter);

void changeNumber(int buttonPress){

switch (buttonPress)

case 0:

digitalWrite(a, LOW);

digitalWrite(b, LOW);

digitalWrite(c, LOW);

digitalWrite(d, LOW);

digitalWrite(e, HIGH);

digitalWrite(f, HIGH);

digitalWrite(g, HIGH);

break;
case 1:

digitalWrite(a, HIGH);

digitalWrite(b, LOW);

digitalWrite(c, LOW);

digitalWrite(d, HIGH);

digitalWrite(e, LOW);

digitalWrite(f, LOW);

digitalWrite(g, HIGH);

break;

case 2:

digitalWrite(a, LOW);

digitalWrite(b, LOW);

digitalWrite(c, HIGH);

digitalWrite(d, LOW);

digitalWrite(e, LOW);

digitalWrite(f, HIGH);

digitalWrite(g, LOW);

break;

case 3:

digitalWrite(a, LOW);

digitalWrite(b, LOW);

digitalWrite(c, LOW);

digitalWrite(d, LOW);

digitalWrite(e, LOW);

digitalWrite(f, LOW);

digitalWrite(g, LOW);
 break;

case 4:

digitalWrite(a, HIGH);

digitalWrite(b, LOW);

digitalWrite(c, LOW);

digitalWrite(d, HIGH);

digitalWrite(e, HIGH);

digitalWrite(f, LOW);

digitalWrite(g, LOW);

break;

case 5:

digitalWrite(a, LOW);

digitalWrite(b, HIGH);

digitalWrite(c, LOW);

digitalWrite(d, LOW);

digitalWrite(e, HIGH);

digitalWrite(f, LOW);

digitalWrite(g, LOW);

break;

case 6:

digitalWrite(a, LOW);

digitalWrite(b, HIGH);

digitalWrite(c, HIGH);

digitalWrite(d, LOW);

digitalWrite(e, HIGH);

digitalWrite(f, LOW);
 digitalWrite(g, LOW);

break;

case 7:

digitalWrite(a, LOW);

digitalWrite(b, LOW);

digitalWrite(c, LOW);

digitalWrite(d, HIGH);

digitalWrite(e, HIGH);

digitalWrite(f, HIGH);

digitalWrite(g, HIGH);

break;

case 8:

digitalWrite(a, LOW);

digitalWrite(b, LOW);

digitalWrite(c, LOW);

digitalWrite(d, LOW);

digitalWrite(e, LOW);

digitalWrite(f, LOW);

digitalWrite(g, LOW);

break;

case 9:

digitalWrite(a, LOW);

digitalWrite(b, LOW);

digitalWrite(c, LOW);

digitalWrite(d, LOW);

digitalWrite(e, HIGH);
 digitalWrite(f, LOW);

digitalWrite(g, LOW);

break;