HM-TR v2.

2
HM-TR Series UHF Wireless Transparent Data Transceiver

General
The HM-TR series UHF wireless transparent data transceiver, developed by Hope
Microelectronics Co. Ltd, is designed for applications that need wireless data transmission. It
features high data rate, longer transmission distance, programmable frequencies, configurable
UART formats and low sleep current make it ideal choice. The communication protocol is self
controlled and completely transparent to users. The module can be embedded to your existing
design so that low cost high performance wireless data communication can be utilized easily.

Features
1. FSK (Frequency Shift Keying) modulation, high interference immunity
2. 2-way half-duplex communication
3. 315/433/868/915MHz ISM band, globally license free.
4. Programmable frequencies, allowing be used in FDMA (Frequency Division Multiple
Access) applications
5. Self controlled RF to UART protocol translation, reliable and easy to use.
6. Configurable UART format, with data rate from 300~19200bps
7. Using ENABLE pin to control duty-cycle to satisfy different application requirements
8. High performance, long transmission range. >300m in open area
9. Standard UART interface, with TTL or RS232 logic level available
10. Compact size, standard 0.1” pinch SIP connector and SMA antenna socket
11. No RF tuning needed in application

Application Areas
1．Remote control, remote measurement system 5. Data collection
2. Wireless metering 6. IT home appliance
3. Access control 7. Smart house products
4. Identity discrimination 8. Data store and forward repeater

Overview and Pin assignment

HM-TR/232 HM-TR/TTL

Note: The ‘232’ version has a on-board MAX232CSE converter, which is not fitted on the ‘TTL’ version
 HM-TR v2.2

Pin name note

1 VDD Power supply
2 DTX Data output from module
3 GND Ground
4 DRX Data input to module
5 CONFIG If this pin is high at power on, module will enter configure
mode, while it communicates if set low
6 ENABLE If this pin is low in normal mode, the module will enter sleep
mode immediately. Assert high will awaken

Parameters
pamameter condition min typical max
Power supply 4.5 5.0 5.0 V
Operate temperature -35 25 80 ℃

Operate frequency HM-TR433 430.24 434 439.75 MHz

HM-TR868 860.48 869 879.51
HM-TR915 900.72 915 929.27

Max output power HM-TR433 3 5 dBm

HM-TR868 -2 0
HM-TR915 -2 0
Transmitting power Pmax-21 Pmax Pmax dBm

Receive sensitivity HM-TR433 -105 -100 dBm

HM-TR868 -102 -95
HM-TR915 -102 -95

TX current HM-TR433 26 mA
HM-TR868 28.5
HM-TR915 30

RX current HM-TR433 15 mA
HM-TR868 16
HM-TR915 17
 HM-TR v2.2
continued

Sleep current HM-TR433/TTL 1 uA

HM-TR868/TTL 1
HM-TR915/TTL 1

Reference distance HM-TR433/TTL 330 m

HM-TR868/TTL 220
HM-TR915/TTL 230

Modulate deviation 15 240 kHz

Receiver bandwidth 67 400 kHz
UART data rate 300 9600 19200 bps
UART data bits 5 8 9 bit
UART parity check None Odd Even
UART stop bits 1 1 2 bit
ANT connector SMA female
Module size 24×43mm

Quick Setup
Connect HM-TR/232 to the RS232 connector of serial fitted PC or connect HM-TR/TTL to
MCU(micro controller unit)’s UART directly，apply power supply, both RED and GREEN status
LED will blink 3 times to indicate it is ready for your application. If CONFIG pin is low at power
on, module will enters normal mode for data transmission, or CONFIG is high the module enters
configure mode to setup work parameters

Note: MCU=Micro Controller Unit, PC=Personal Computer, GPIO=General Purpose Input/Output

Normal mode connection
In normal mode, the ENABLE pin controls the module work or sleep, module will enter
sleep mode as soon as the pin is low level.
 HM-TR v2.2

Configure mode connection (HM-TR/232)

Configure mode connection (HM-TR/TTL)

In configure mode, the module work parameters can be setup via the HM-TR setup utility,
with the communication format between module and computer fixed at: 9600, 8, N, 1. see below:
 HM-TR v2.2
HM-TR SETUP UTILITY

“Read” button: Read the parameters the module currently use;

“Write” button: Write new configuration to module;
“Default” button: Recover module parameters as default value

Ordering Information
Model Logic Level
HM-TRxxx/TTL TTL
HM-TRxxx/232 RS232
232 versions usually are used in PC or equivalent, TTL version suited for simple 5V MCU system.

Module Naming Rule

HM-TR 315 / TTL

Logic Level：TTL—TTL
232—RS232

Frequency： 315 band—315MHz;

433 band—434MHz；
868 band—869MHz；
915 band—915MHz。
TX or RX：TR—TX and RX
Product Code
 HM-TR v2.2
Mechanical outline:

This document may contain preliminary information and is subject

to change by Hope Microelectronics without notice. Hope
Microelectronics assumes no responsibility or liability for any use of
the information contained herein. Nothing in this document shall
operate as an express or implied license or indemnity under the
HOPE MICROELECTRONICS CO.,LTD intellectual property rights of Hope Microelectronics or third parties.
Address: Rm B.8/F LiJingGe Emperor The products described in this document are not intended for use
Regency 6012 ShenNan Rd, Shenzhen, China in implantation or other direct life support applications where
Tel: 86-755-82973805 malfunction may result in the direct physical harm or injury to
Fax: 86-755-82973550 persons. NO WARRANTIES OF ANY KIND, INCLUDING, BUT
Email: sales@hoperf.com NOT LIMITED TO, THE IMPLIED WARRANTIES OF
hopefsk@hoperf.com MECHANTABILITY OR FITNESS FOR A ARTICULAR PURPOSE,
Website: http://www.hoperf.com ARE OFFERED IN THIS DOCUMENT.
http://www.hoperf.cn
http://hoperf.en.alibaba.com ©2006, HOPE MICROELECTRONICS CO.,LTD. All rights reserved.