Professional Documents
Culture Documents
How Do You Set System Gain Structure?: by Chuck Mcgregor
How Do You Set System Gain Structure?: by Chuck Mcgregor
INTRODUCTION
BACKGROUND YOU NEED TO KNOW
Realistically, audio signals at or near the noise floor of a system are not useful because the signal will not be
significantly louder than the noise. Therefore, some minimum usable level must be assumed below which the
electronic noise is considered objectionable. A signal to noise ratio of 20 dB is considered minimally acceptable
for good intelligibility. For a high quality system 30 dB would be a better figure to use. Using this value, the
range from this minimum signal level (30 dB above the noise floor) to the clipping level is the usable signal range
window for the system (also called the dynamic range in my way of thinking). However, for purposes of this
paper, the maximum output to noise floor is used as the dynamic range.
Every audio system with more than one electronic component has a "system gain structure". Gain structuring for
a system occurs in the signal processing chain between the mixer or another signal source and the power
amplifiers. One usual scenario is to set all the signal processors to unity gain and turn the amplifier inputs to
maximum. Unfortunately as you will see, given the different maximum outputs and noise levels of typical signal
processors, this method will may not come close to the best gain structure.
We will be dealing with the signal voltage levels on the interconnecting cables from the output of the mixer (or
signal source if there is no mixer) up to the input of the amplifier. For the convenience of using simple numbers,
this analysis uses relative dB, as a voltage ratio where dB = 20 x log (V1/V2), and dBu, where 0 dBu = 0.775V.
V1 and V2 are simply two voltages.
To set proper gain structure, the interconnections between devices must be constant voltage interfaces. This
means an output device's voltage at any point in time is unaffected by whether or not it is connected to the
device(s) it is driving. This type of interface is characterized by the output impedance of a device being 1/10 or
less of its load. For example, if the output impedance is 100 Ohms, the total load it drives must be 1000 Ohms or
greater. Virtually all professional audio equipment meets this criterion when a single device drives only one other
device. However when one device drives multiple devices, such as a mixer feeding a number of power amplifiers,
this may not be true. In this case a distribution amplifier may be needed to divide the load between its multiple
outputs.
The last thing to consider is the power handling of the loudspeaker(s). As long as the amplifier does not exceed
the loudspeaker's power handling capability and the system is operated without clipping, you should never blow a
properly manufactured loudspeaker. The safest criteria to use in selecting an amplifier is the RMS rating of the
loudspeaker. In reality, most loudspeakers can handle peak signals in excess of this rating. A reasonable choice is
an amplifier whose rating that is 2 times (+3 dB) the RMS rating of the loudspeaker. The RMS sine wave used to
rate amplifiers has an inherent peak power component of 3 dB. So this all works out to a 6 dB allowance for
power peaks over the loudspeaker's RMS rating. This is a pretty safe figure for the way most professional
loudspeakers are rated (pink noise with a 6 dB peak factor) and given the peak to RMS content of most audio
signals. However, sustained sine wave signals from the likes of a synthesizer could exceed the loudspeakers RMS
capability by 3 dB without clipping the system. If you expect these kinds of signals and you expect to drive the
system to maximum output levels with them, use the loudspeaker's RMS rating as the power rating for the
amplifier.
With these basics in mind, we're ready to examine how to achieve proper gain structure in detail.
Each device is represented by what looks like a bar. Rather than a bar, picture it as a tall, narrow window. The
maximum output or clipping point from the specifications for each device defines the top of the window using the
absolute dBu scale on the right. The published noise floor (or signal-to-noise ratio) specification below maximum
output determines the height of the window. The relative dB scale on the left is used to determine this height. All
usable signals must pass between the top and bottom of the window. However, remember that your low level
signals won't be near the noise floor. Realistically the minimum usable signal is one that is at least 30 dB above
the noise floor.
Next, a horizontal line is drawn across the top of the lowest window (in this case the amplifier). This is the system
clip level, and for the rest of the analysis this line stays in the same place. Another line is drawn across the highest
bottom window sill (in this case the mixer). The relative dB scale is used to measure the distance in dB between
the 1st and 2nd lines. As you can see, it is only 72 dB for this set of devices and gain structure. That's equal to the
performance of your average consumer cassette deck -- and you thought that professional equipment
automatically guaranteed a professional grade audio system. Oh well, live and learn!
Now subtract 30 dB to find the "true" dynamic range (30 dB above the noise floor to the clipping level). The
result is 42 dB. Measurements of the maximum dynamic ranges for acoustic instruments and voice yield
maximum figures in excess of 40 dB. This means our system really doesn't have enough dynamic range to
reproduce them.
The noise floor line is redrawn through the highest window sill (in this case still the mixer). Because this ends up
12 dB lower than in FIGURE 2 relative to the system clip level, we see that the system's overall window height is
now 84 dB. This is a 12 dB improvement - much better. Note that the absolute device clip levels no longer relate
to the absolute dB scale except for the amplifier's input after its input attenuator. Our usable signal range (from 30
dB above the noise floor) is 54 dB. This means our system is now able to squeak out enough range to reproduce
the dynamic range of instrumental and vocal sources.
Unfortunately, the mixer is still the primary noise source by 3 dB over the signal delay. However, according to
their published specifications, the mixer should have some 6 dB better noise performance than the signal delay. It
should also be obvious the signal delay is the weakest dynamic range link because it has the shortest window.
Therefore, we must conclude that there is more that can be done to optimize the system's gain structure.
lined up on the system clip level line. To do this, start with FIGURE 1 and work from left to right in signal flow
fashion. If you move a window up you need gain between it and the next device. If you move a window down
you need a pad.
First, move the mixer window down so its top is even with the graphic EQ window. This movement is measured
on the relative dB scale, which in this case is -6 dB. Therefore, you need a 6 dB pad at the input of the graphic
EQ.
Next, move BOTH the mixer and graphic EQ windows down together so the graphic EQ window is even with the
top of the notch filter window. This also turns out to be -6 dB. Therefore, a 6 dB pad is needed between the EQ
and notch filter.
Now, move the mixer, graphic EQ and notch filter windows together so the top of the notch filter window is even
with the top of the signal delay window. To do this, move ALL the previous devices up 3 dB. This means you
need 3 dB of gain between the notch filter and signal delay.
Repeat the process again by moving the windows of the first four devices together so the top of the signal delay
window is even with the limiter window. This distance equals 3 dB. This means 3 dB of gain is needed between
the signal delay and limiter.
Lastly, you must lower ALL device windows to line up with the input to the amplifier. They are moved the
distance between the top of the limiter and the top of the amplifier. In this example the distance is 18 dB. (In the
actual system this would usually be done with the amplifier input attenuator.)
After completing all these steps, the tops of the windows end up on the system's clip level line as shown in
FIGURE 3 (+3 dB on the absolute dB scale). Looking back from inside the amplifier after its input attenuator, all
devices appear as though they are clipping at +3 dB. In reality, they are all clipping at their specified device clip
levels. If one device is clipping -- everything is clipping.
Measure the distance between the system's clip level line and the bottom of the shortest window using the
left-hand scale. This result is 90 dB which is 18 dB better than the raw system gain structure in FIGURE 1. The
"true" dynamic range, considering a 30 dB above the noise floor signal as the minimum, is now 60 dB. Also, the
primary noise source is now the signal delay. This is the weak link, which agrees exactly with the published
specifications for all the devices. It also should be apparent that more of the usable signal window within each
device is being used. What a concept.
In some cases, pads or gain will not have any effect on the overall usable signal range. For example, in FIGURE
3, the 3 dB of gain at the output of the signal delay could be omitted. The 18 dB pad for the amplifier input would
become only 15 dB, and the top of the limiter window would end up 3 dB above the system clip level. The key
here is that the bottom of its window is still well below the noisiest device (in this case the signal delay). You can
use this reasoning to save yourself the hassle of making up small pads or small amounts of gain. If you omit one
of these along the chain you MUST move all the devices preceding it up or down in your chart by the dB of gain
or loss that you are omitting. Otherwise, you will not see the effects of the omission on the noise floor.
Background Noise
Now that you have set up proper system gain structure on paper, it is time to hook-up the system and do the same
thing for real. Once completed, audibly evaluate the noise floor heard from the speakers. If all is quiet, pack up
and go home. If the noise floor is too high, there are two possibilities:
A. The maximum sound level is higher than necessary, which means you over-designed the maximum capability
for the system. If this is the case, turn down the amplifier input attenuator. You will lower the noise, and the
maximum output level for the system will be reduced by the amount you decide is over-kill.
B. The maximum sound level you can get out of the system IS necessary, which means your system does not
have enough usable signal range. You now have three choices; the first two are compromises.
1. Accept the noise and achieve the maximum sound level you need.
2. Turn the amplifier input down to make the noise acceptable. This will, of course, reduce the maximum output
level capability for the system. (Sorry, you can't have it both ways unless you pick choice 3.)
3. Change the primary noise source in the system to something with lower noise performance.
A similar chart for setting up proper system gain can be created for any system. Using graph paper, make a
vertical absolute dB scale from about +30 dB to -120 dB so you can plot increments for 3 dB or less. The relative
dB scale simply uses the same graph increments for plotting and measuring distances in dB.
You could also follow this procedure by using some simple math. If you don't trust your addition and subtraction,
or would rather work with pictures (they are more dramatic and will quickly show errors in your thinking) cut out
rectangular paper bars (windows) like those shown in the figures. The length of each should equal the distance in
dB between the device clip level and its noise floor. Be sure to convert noise figures to noise below maximum
output.
Write in the clip level for each device on its window. Using these numbers and the absolute dB scale, position the
top of each window on the graph paper in signal flow order from left to right. Move these "paper cut-outs" up and
down on the chart as outlined above, by measuring the distances using the relative dB scale. You can very quickly
determine the necessary pads and gains -- probably faster than with a calculator.
A way to check your work is take the maximum output for the first device and subtract the dB for the all the pads
and the gain to that number, including the pad before the amplifier. The result should equal the maximum input
sensitivity for the amplifier. This calculation should give math mavens an interesting insight into the gain
structure process.
To actually adjust a system you need to do exactly what you did on paper except you are now doing it for real.
You start from the console output and find out what you need (gain or loss) to adjust its maximum output signal
so that it just drives the next device into clipping. And so on.
You don't need to know the specifications of the equipment. When you go through the system you'll find out what
those specifications are in terms of maximum output levels. As you should have understood by going through the
exercise on paper, the noise floors of the equipment will take care of themselves. Some device (like the signal
delay in the above example) will be the weak link. There is nothing you can do to make this better except to
replace it with a device with a better maximum output to noise floor window (better signal to noise ratio
specification.
Because of production variations and possibly conservative specifications, you may be able to pick up a few more
dB of dynamic range by adjusting the pads or gain values you determined on paper. If things are not reasonably
close to your on-paper calculations, you have a problem such as bad wiring or a mis-adjusted or defective device.
What To Adjust
When you set gain in the system, the attenuation or gain needed between devices can be added externally or by
using a device's input level control, if it has one. DO NOT ADJUST ANY DEVICE'S OUTPUT LEVEL
CONTROL - this should be left at maximum. This is because it is rarely the last thing in the internal circuitry
before the output connector. Unlike some input level controls, it usually does NOT adjust actual gain. Therefore
using it will squash the dynamic range in that device's output stage and you may end up making things worse,
even though the signal level is matched up to the next device. Use an output control only if you KNOW
ABSOLUTELY that it is a simple attenuator feeding its output connector. The reason it usually is not is that this
topology would cause changes in the output impedance when the control is set for anything other than maximum.
Among other things this could would wreak havoc with - guess what - the gain structure. If the device has a noise
floor below other devices when you have set the overall gain structure, you can use output gain. But reduce it
only by 3 dB less than the amount between the device's noise floor and the device that determines the noise floor
of the system. This is because if you bring its gain, and hence its noise floor, up to the worst case device its noise
will add to the worst case device and give you 3 dB less dynamic range.
To find the clip points in a system, you need to use an oscilloscope and a pink noise test signal. There is really no
good substitute for this equipment to set gain structure. Sine wave signals are not recommended as they only
show one frequency at a time and you can easily miss something. The pink noise should be full-range (20 Hz - 20
kHz) and have at least a 6 dB peak to average ratio. If you can find one with a 10 dB peak to average ratio, you
will more closely simulate real audio signals.
If you must use sine wave signals, you will have to check each and every EQ boost frequency or range of
frequencies very carefully. When measuring electronic crossovers or other frequency response limiting devices,
only a full-range pink noise signal will allow you to see full-range signal energy losses easily. (See sections on
crossovers and band limited devices.) If using sine waves you must set the frequency to the center point of each
frequency band of the crossover or the center of the band pass for a band limited device.
For simple systems (e.g. no electronic crossover), there is "poor man's" method where you use a Piezoelectric
tweeter and a 400 Hz sine wave to find clip levels. Basically, you connect the tweeter directly to the output of
each device. When the device hits clipping, the tweeter will emit a very noticeable buzzing sound due to the
harmonics in the clipped signal. For high-powered amplifiers, a resistive pad should be used to avoid burning out
the tweeter. This method is detailed more rigorously by Pat Brown of Syn-Aud-Con. You can find this
information as a PDF file on the internet at http://www.synaudcon.com/downloads/piezo.pdf.
Doing It
You start the whole procedure by inputting the pink noise test signal into to mixing console. Set it so that it's
output just clips as seen on the oscilloscope. Make sure it is the output of the mixing console that is clipping.
Determine this by reducing the master fader. The clipping should stop. If it doesn't, you are clipping something
before the output fader. While you're at this point, note the reading on the output meter. This is a good indication
of what the meter will read when you have reached the system's maximum output after you set its gain structure.
If you are using sine waves this will NOT be a reliable indication.
Once completed, if the system noise levels are low enough, you may want to increase the setting of the
amplifier(s) input level control. This will make the mixer more sensitive for operation. If you reduce the amplifier
input level control, something in the front end of the system will clip first. This means the amplifier will not reach
full output. But it WILL reproduce that clipped signal and possibly damage the loudspeakers. Either way -- if you
choose to increase or reduce the amplifier's input sensitivity from the optimum gain structure setting -- you really
don't gain (pun intended) anything.
There is possible exception to this: by reducing the amplifier's input level control, the output meters on the
console will indicate you have reached the system's maximum output before the amplifier's clip. This is useful so
that a less than capable mixing engineer will THINK he's pushing things to the limit but there will still be
something left in the amplifiers. This may help protect the loudspeakers but, bear in mind, it will limit the
maximum output of the system to something less than it could be.
Note that to reach a system's maximum output analog Vu meters on mixing consoles may "peg" before the system
clips. If you can afford the reduction in dynamic range, operating the system so the meters don't peg means you'll
never clip the system. Generally, this means you won't ever blow the loudspeakers assuming the amplifiers are
chosen not to exceed the loudspeaker's maximum ratings.
Up to now we've looked at a simple systems. Here is where gain structure gets more complicated. However the
ideas are exactly the same. You just have to think about what specific pieces of equipment do and/or about more
signal paths.
Parts 1 - 3 assumed devices in the signal chain have no gain (unity gain devices). However, a device may have
gain or loss, or you may want to allow for boosts in an EQ, which may be needed to tune the system. EQ boosts
are like adding overall gain to the device. In such cases, as illustrated in FIGURE 4, input of the device's window
is shifted down below the output of the device's window. The distance will be the gain in dB for this device or the
desirable dB boost you choose for the EQ. In this case, it is assumed the boosts will be limited to a maximum of 6
dB. Match the top of the window of the preceding device to this line. On the output side you still use the top of
the window to match it to the next device.
When adjusting gain in an actual system, first set up the system with the EQ set to flat. Then make any EQ
adjustments. If all your EQ is cut only, you can usually leave everything as is. However, if you add ANY EQ
boosts, you will then have to redo the gain structure starting from the input to the EQ by finding the new
maximum level it can accept without clipping. This will of course require attenuation at the input to the EQ input.
In some instances a device might introduce a loss in signal level. The procedure is similar except that the output
side of the device's window is shifted to below the input of the device's window a distance equal to the loss in dB.
Use this new output point to match the device to the top of the window of the following device. In the example it
is assumed the limiter threshold is set so the maximum signal through the limiter is 6 dB below its maximum
output. However, on the input side you still use the top of the device's window for matching to the preceding
device's window. The relative signal level prior to the limiter is 6 dB higher. As shown in FIGURE 4, everything,
including the noise floor is raised 6 dB. The system dynamic range is still determined by the signal delay, because
that is still the smallest "window" in the overall picture.
Because the maximum input of the amplifier (after its input attenuator) is still + 3 dB it has remained in the same
position throughout
Another variation in this procedure is when a system has several branches, such as a mixer feeding multiple
sub-systems. You have to separately analyze each branch and include in each analysis the source common to all
branches (the mixer in the example FIGURE 5). This will automatically optimize the system so that the common
source and all the branches clip at once. To do this, the mixer In FIGURE 5 must feed each branch through a
separate pad. Note that the dynamic range is different in each branch.
To balance the multiple branch systems acoustically in the actual system, you will probably need different
operating levels in the branches than what the optimized electronic gain structure provides. An example would be
a central cluster with delayed balcony speakers. To balance operating levels in these instances, use the branch that
is lowest in acoustic level as your reference branch (i.e. the one you are itching to turn up because it isn't loud
enough - but don't touch that dial). Use the input attenuation on the amplifiers for each of the OTHER branches.
This will reduce their output levels and achieve proper acoustic balance with the reference branch. This will also
have the effect of lowering the noise levels and reducing the maximum capability of the other branches. In this
case, less capability is acceptable because you have determined that the maximum capability can't be used in
these branches unless you drive the reference branch into clipping.
However, if you find, for example, that you have to significantly reduce the maximum output capability of the
central cluster so you won't clip the balcony system, then your balcony system is under-powered. Instead of
attenuating the central cluster, you could add gain prior to the balcony system amplifiers (or "unattenuate" the
amplifier input). While this will balance the system, the balcony amplifiers will be driven into clipping before the
central cluster amplifiers.
In this situation, the only way you can have your cake and eat it too, is to increase the size of the balcony
amplifier, which translates to more voltage (power) capability for the balcony speakers. You will not spot this
problem by analyzing the electronic gain structure. This could only have been spotted on paper with proper
analysis of the acoustic output for each branch based on speaker sensitivities and listening distances.
Electronic Crossovers:
Electronic crossovers require special attention. Consider a full-range signal with equal energy per octave (e.g.
pink noise). A crossover will divide the total energy of such a signal among two or more frequency bands. This
causes an inherent signal loss at each band-limited output, compared to the full-range crossover input signal. In
effect, crossovers are NOT unity gain devices when fed a full-range signal. You can approximate these losses by
calculating how much of the total energy is in each frequency band by using the following procedure:
Example: A 3-way crossover with frequency bands of 50 Hz - 125 Hz, 125 Hz - 500 Hz, 500 Hz -10 kHz.
1. Multiply the lowest frequency in each band by 2 until you get to the highest frequency for that band. The
number of times you multiplied = the number of octaves. Round off the results for each band to the nearest whole
octave [= 1, 2, 4].
2. Add up the total octaves from all bands [= 7].
3. Divide the octaves in each band by the total octaves [= 0.14, 0.29, 0.57]
4. Push the LOG key for each result [= -0.9, -0.6, -0.2].
5. Multiply each result by 10 to find the approximate losses [= -9 dB, -6 dB, -2 dB].
Note the low frequency output is down almost 10 dB. That is why many systems have problems achieving
enough drive levels for the subwoofers.
Now you must draw horizontal lines on the output side of the crossover's window. Draw these lines at a distance
below the top of the window equal to the loss in dB for each output as found above. This line for each crossover
output is used to match up the crossover window to the top of the window of the device it feeds (usually an
amplifier). In the example, a different pad would be needed for each output (assuming the amplifiers have equal
input sensitivities). The top of the window of the device feeding the crossover is still matched to the top of the
crossover's window.
In the actual system, the amplifier input levels are adjusted to acoustically balance the system similarly to a
multiple branch system. Use the frequency band that you want to turn up the most - typically the subwoofer (but
of course you won't turn it up - right?) as the reference output. Balance the other bands to it by turning DOWN
their amplifier input level controls.
Once you have the system balanced to your acoustical liking, you may find that amplifier input level controls, in
particular for horn amplifies, may be set too low for them to reach full output - even with a single frequency sine
wave in their pass band. You can increase all the amplifier input level controls by the same amount to get some or
all of this unusable capability back for limited frequency range signals. Keep in mind, however, that this will have
two consequences: It will raise the acoustic noise floor of the system and the capability for full-range signals will
remain the same. However, some amplifiers will clip before the signal processing in the system.
This is another situation where you must accept a compromise or change amplifier sizes to get a better match in
gain and capability between the different frequency bands.
There is a more general case, similar to the crossover scenario. If you have full-range signals at the input of a
device that limits the frequency response -- such as with high or low pass filters -- there will be an energy loss
from its input to output. Calculate this loss using the same procedure outlined in the previous section on
electronic crossovers. The significant energy of full range music signals effectively spans about 9 octaves
(approximately 30 Hz to 15 kHz).
Example: An under balcony system band limited from 150 Hz to 5 kHz.
1. Multiply the lowest frequency limit of the device by 2 until you get to the highest frequency limit for the
device. The number of times you multiplied = the number of octaves. Round off the results to the nearest whole
octave [= 5].
2. Divide the number of octaves by the 9 full-range octaves [= 0.56].
3. Push the LOG key for this result [= -0.3].
4. Multiply this result by 10 to find the approximate loss [= -3 dB].
Now you must draw a horizontal line on the output side of the device's window. The line is drawn at a distance
below the top of the window equal to the loss in dB as found in #4 above. This line is used to match up the
device's window to the top of the window of the following device.
The purpose of a system limiter in a properly gain structured system is to prevent any signals from exceeding the
system's maximum level. As such, it is used as an "emergency" device meaning it is intended to provide a hard,
never-to-exceed maximum output level. Limiter/compressors with soft-knee thresholds are not as ideal for
protection. You really want something that doesn't do anything up to a certain point then stops any further
increase cold in its tracks. Because you need some margin between the device's maximum input and its limiting
threshold they are a bit tricky to implement properly without compromising the system's dynamic range.
Just as with any other device you must introduce the limiter using its input, output, noise floor specifications, and
gain setting just as with any other device in the system. Because of the way they work, the threshold setting is
used as the maximum input. For proper functioning the threshold should be set to at least 3 dB lower than the
maximum output signal from the device preceding it. The limiter's output gain should be used to adjust its
maximum output at threshold to about 2 dB below the input level of the device it feeds. This allows a little
"margin for error" in the protection.
If you think about it, the only point you can put a limiter in a properly gain structured system that will truly work
perfectly is at the output of the signal source. It would be set so that the input level to system would never allow
the first device it feeds to clip. This is technically practical if only one signal source is used at a time (i.e. not
mixed with others). Therefore, if you are simply switching between multiple input sources, put your limiting
device at the output of the switcher. The system sees one input source and really doesn't care which one it is and
no input signal can drive the system into clipping.
With multiple mixed sources and a properly set system gain structure, the next best place to put the device is at
the output of the mixer. This is because any mixer output voltage at any frequency exceeding the system's
maximum output will clip the system somewhere. With multiple branch systems you might think to use a limiter
on each branch. But with proper gain structure they would either all work at once or compress some part(s) of the
system and not others, thus upsetting the acoustic balance. Thus a single limiter for each main output that is
controlled by the operator makes the most sense. "Controlled by the operator" means outputs such as a separate
sub-woofer output where the acoustic balance is actively "mixed" by the operator based on the input signal
content. You should make sure the operator can see when a threshold is exceeded to avoid clipping the mixer.
If the noise floor of the mixer is low enough compared to the other devices in the system you can allow more than
the 3 dB margin the mixer has above the limiter's threshold. You can do this by reducing a pad between the mixer
and the limiter. You can also lower the limiter's threshold level (and increase the output of the limiter by the same
amount) if the noise floor of the limiter allows this.
Because it is used as a "hard-line" device, you should set the compression ratio to maximum (10:1 or higher if
available). As to any attack and release settings, they do not affect the gain structure. However, as the limiter is
intended to function only as an emergency protection device, there is every reason to use the fastest attack and
release times. You are not going for sound quality here; you are protecting the system from any overdrive. So get
into and out of protection as fast as possible. If you think sound quality IS important, then you are not thinking
correctly. What you should have thought about is a more powerful system that would rarely be pushed into
limiting. In other words if the system is constantly pushed into limiting, it is under-designed.
SUMMARY
Gain structure is only a problem because invariably we use equipment with different input/output capabilities and
noise floors. There is no easy way to properly set system gain except to analyze each device in relation to the
device that feeds it and in relation to the entire signal path. Fortunately, the little information you need is readily
available on equipment specification sheets. By working out proper gain structure on paper before you purchase
and wire up the equipment, you can spot potential problems and make appropriate substitutions. In any case, with
the gain properly structured, you can make significant, or in some cases, spectacular improvements in the
system's dynamic range and its noise floor. In the example system, 18 dB is certainly a spectacular improvement.