ONE POINT REPAIR GUIDE

1. NO POWER
If the unit doesn’t work by no power problem, repair the set according to the following
guide.

1-1. FUSE & BRIDGE DIODE

1-1-1. Solution
Please check and replace F901, BD901, TH901 on SMPS board.

1-1-2. How to troubleshoot (Countermeasure)

1) Check if the fuse F901 is open or short-circuit.
2) Check if the bridge diode DB901 is short-circuit by over current with a digital multi meter.
3) Check if the NTC thermistor TH901 is normal or open.

i
m
jo
1-1-3. Service hint (Any picture / Remark)

< F901 > < BD901 > < TH901 >

If F901 is not short-circuit, If BD901 is short-circuit, If TH901 is open,
replace it with a same replace it with a new one. replace it with a new one.
specifications one.

3-2
 ONE POINT REPAIR GUIDE
NO POWER
If the unit doesn’t work by no power problem, repair the set according to the following
guide.

1-2. D929
1-2-1. Solution
Please check and replace D929 on SMPS board.

1-2-2. How to troubleshoot (Countermeasure)

1) Check the Anode-Cathod Voltage of D929 with a digital multi-meter, it is normally 0.2 ~ 0.3 V.
If it doesn’t have any voltage, it’s destroyed. Replace it with a new one.

1-2-3. Service hint (Any picture / Remark)

i
m
jo

< SMPS schematic diagram >

3-3
 ONE POINT REPAIR GUIDE
2. NO BOOTING WHEN POWER ON THE SET
The set doesn’t work when press the power button on the front board or the remote
control.

2-1. FLASH MEMORY

2-1-1. Solution
Please check and replace IC101 on MAIN board.

2-1-2. How to troubleshoot (Countermeasure)

1) Check 3.7 V to CN304 and CN105 in standby mode.
If there is no 3.7 V, check the SMPS.
2) Check 5.6 V, 12 V, F+, F- and PVDD when power on the set.
- If the set doesn’t work regardless of what the KEY1 changes high to low while pressing the power button.
X101 and X102 work normally but, if you can not power on the set, replace IC101 with a new one on
the MAIN board.

2-1-3. Service hint (Any picture / Remark)

 XWX

i OZYU^]_ro¡P
m
rl€ X
O—•]WP  XWY
O`U_ZW[to¡P
jo
w~ y†j{ys
OyXX`P

pjXWY

< Signal check point >

3-4
 ONE POINT REPAIR GUIDE
3. VFD IS NOT DISPLAYED WHEN POWER ON THE SET
When power on the set, any icons or characters on VFD are not displayed.

3-1. VFD
3-1-1. Solution
Please check and replace DIG502 on FRONT board.

3-1-2. How to troubleshoot (Countermeasure)

1) Check if VKK, FL+ and FL- are output from SMPS to VFD via the MAIN board.
2) Check if IC102 outputs VFD_D0, VFD_CLK and VFD_STB to the FRONT board.
3) Check the GR signal(pulse signal) of IC501 on the FRONT board.
Check the SG signal(pulse signal) of IC501 on the FRONT board.
If the GR and SG signal isn’t output, replace IC501 with a new one.
If the GR and SG signal is output, replace DIG502 with a new one.

3-1-3. Service hint (Any picture / Remark)

i
m
nyGšŽ•ˆ“ nyGšŽ•ˆ“
h‰–œ›GZWG
jo
yZY^O{wZW[P
znGšŽ•ˆ“

znGšŽ•ˆ“
h‰–œ›GZWG

j“Š’G›ŒG—Š›œ™ŒSGˆ•‹G›Œ•G‹™ˆŽG›–G
Œ•“ˆ™ŽŒG›U
ŠŒŠ’G›ŒGžˆŒ–™”G–•G‹Œ›ˆ“šU

< Waveform of GR and SG signal >

3-5
 ONE POINT REPAIR GUIDE
4. NO OPERATION OF MD
When no sound output in the CD function, you can not listen to music reading data
from a CD disc if the servo motors in MD don’t work. This step is for checking the
SPINDLE MOTOR among them.

4-1. SPINDLE MOTOR

4-1-1. Solution
Please check and replace IC301, IC302 on MAIN board.

4-1-2. How to troubleshoot (Countermeasure)

1) Check the SPDO signal from pin16 of IC302.
If no signal, check 3.3 V(RF) and X301.
2) Check the SPIN- & SPIN+ from IC301 to CN303 for driving SPINDLE motor. It is about 3.6 Vp-p.
If no signal, check +1.8 V and +5 V for IC301.
3) Check if the FFC cable is solidly connected between CN303 and MD.
4) Check the MD.
If the spindle motor is sort-circuit or has any trouble, it can not rotate CD discs.
Please check the function after changing another MD.

4-1-3. Service hint (Any picture / Remark)

i
m zwT
—•] ›–GjuZWZ

pjZWX
jo
ˆ‰–œ›G
ZU]} —T—

zwT ›–GjuZWZ

zwRG›–GjuZWZ

zwR
—•\ ›–GjuZWZ

< Waveform of SP- & SP+ < Signal check point >
for driving SPINDLE motor >

3-6
 ONE POINT REPAIR GUIDE
NO OPERATION OF MD
When no sound output in the CD function, you can not listen to music reading data
from a CD disc if the servo motors in MD don’t work. This step is for checking the
SLED MOTOR among them.

4-2. SLED MOTOR

4-2-1. Solution
Please check and replace IC301, IC302 on MAIN board.

4-2-2. How to troubleshoot (Countermeasure)

1) Check the SLDO signal from Pin15 of IC302.
If no signal, check 3.3 V(RF) and X301.
2) Check the SLED+ & SLED- from IC301 to CN303 for driving SPINDLE motor. It is about 2.9 Vp-p.
If no signal, check +1.8 V and +5 V for IC301.
3) Check if the FFC cable is solidly connected between CN303 and MD.
4) Check the MD.
If the sled motor is sort-circuit or has any trouble, it can not move the pickup module.
Please check the function after changing another MD.

4-2-3. Service hint (Any picture / Remark)

i
m
z sR
—•Z ›–GjuZWZ

h‰–œ›G
YU`} —T— pjZWX
jo
zsT ›–GjuZWZ
zwT ›–Gju[W\
zsRG›–GjuZWZ
zwRG›–Gju[W\

z sT
—•[ ›–GjuZWZ

< Waveform of SLED- & SLED+ < Signal check point >
for driving SLED motor >

3-7
 ONE POINT REPAIR GUIDE
NO OPERATION OF MD
When no sound output in the CD function, you can not listen to music reading data
from a CD disc if the servo motors in MD don’t work. This step is for checking the
TRAY OPEN / CLOSE MOTOR among them.

4-3. TRAY OPEN / CLOSE MOTOR

4-3-1. Solution
Please check and replace IC301, IC302 on MAIN board.

4-3-2. How to troubleshoot (Countermeasure)

1) Check MOT_OPEN & MOT_CLOSE signals from Pin104, 105 of IC801 to IC301.
If no signal, check +1.8 V & + 5 V to IC301.
2) Check LOAD± from IC301 to CN303 for driving the tray open / close motor. It is about 3.85 Vp-p.
If no signal, check +5 V to IC301. If it has any trouble, replace it with a new one.
3) Check if the FFC cable is solidly connected between CN303 and MD.
4) Check the MD.
If the tray motor is sort-circuit or has any trouble, it can not open or close the tray.
Please check the function after changing another MD.

4-3-3. Service hint (Any picture / Remark)

i
m tv{†vwlu
^—•G–GpjZWX
svR
—•\ –GjuZWY

h‰–œ›G
ZU_\} —T—
pjZWX
jo
tv{†vwlu
tv{†jsvzl
svT ›–GjuZWZ
svRG›–GjuZWZ

tv{†jsvzl svT
]—•G–GpjZWX —•[ ›–GjuZWY

< Waveform < Signal check point >

for driving TRAY open / close motor >

3-8
 ONE POINT REPAIR GUIDE
NO OPERATION OF MD
When no sound output in the CD function, you can not listen to music reading data
from a CD disc if the pickup module in MD doesn’t work. This step is for checking the
LASER TRACKING ACTUATOR.

4-4. LASER TRACKING ACTUATOR

4-4-1. Solution
Please check and replace IC301, IC302 on MAIN board.

4-4-2. How to troubleshoot (Countermeasure)

The tracking actuator makes the laser beam be positioned in the center of a track on CD disc.
1) Check the TRD signal from Pin14 of IC302.
If no signal, check 3.3 V(RF) and X301.
2) Check TR- & TR+ from IC301 to CN301 for driving the tracking actuator.
If no signal, check +1.8 V and +5 V for IC301.
3) Check if the FFC cable is solidly connected between CN301 and MD.
4) Check the MD.
If the pickup module has any trouble, it can not move the laser beam on the left or right side.
Please check the function after changing another MD.

4-4-3. Service hint (Any picture / Remark)

i
m {T
—•X\ –GjuZWX

pjZWX
jo
{yT ›–GjuZWX
{yRG›–GjuZWX
{R
—•X[ –GjuZWX

< Waveform of TR± < Signal check point >

for driving TRACKING actuator >

3-9
 ONE POINT REPAIR GUIDE
NO OPERATION OF MD
When no sound output in the CD function, you can not listen to music reading data
from a CD disc if the pickup module in MD doesn’t work. This step is for checking the
LASER FOCUSING ACTUATOR.

4-5. LASER FOCUSING ACTUATOR

4-5-1. Solution
Please check and replace IC301, IC302 on MAIN board.

4-5-2. How to troubleshoot (Countermeasure)

The focusing actuator makes the laser beam keep a regular interval with the surface of a CD disc.
1) Check the FOD signal from Pin13 of IC302.
If no signal, check 3.3 V(RF) and X301.
2) Check F- & F+ from IC301 to CN301 for driving the focusing actuator.
If no signal, check +1.8 V and +5 V for IC301.
3) Check if the FFC cable is solidly connected between CN301 and MD.
4) Check the MD.
If the pickup module has any trouble, it can not move the laser beam on the top or bottom side.
Please check the function after changing another MD.

4-5-3. Service hint (Any picture / Remark)

i
m
{T mR
—•XZ –GjuZWX

pjZWX
jo
mRG›–GjuZWX

mT ›–GjuZWX

mT
—•X] –GjuZWX

< Waveform of TR± < Signal check point >

for driving FOCUSING actuator >

3-10
 ONE POINT REPAIR GUIDE
5. NO SOUND
There is no sound output in the CD FUNCTION, repair the set according to the follow-
ing guide.

5-1. IN THE CD FUNCTION

5-1-1. Solution
Please check and replace IC602, IC801 on MAIN board.

5-1-2. How to troubleshoot (Countermeasure)

1) Check CD_BCK, CD_LRCK, & CD_DATA signals from IC302 to IC801.
If no signal, check if the RF & servo signals from MD is entered to IC302.
Refer to the “No operation of MD” guide on Item 4.
2) Check the following I2S signal flow. < I2S audio signal Interface >
- DAC_BCK: IC801_Pin87 --> IC602_Pin4
- DAC_LRCK : IC801_Pin88 --> IC602_Pin5 (44.1 kHz)
- DAC_DATA : IC801_Pin83 --> IC602_Pin6,9
- DAC_MCLK : IC801_Pin86 --> IC401_Pin44
If there is any trouble, check the power for each IC. The power is normal but, if the signal waveform to
the IC is distorted or no signal, replace it with a new one.
3) Check if “Digital audio AMP block” on Item 5-2 is normal.

5-1-3. Service hint (Any picture / Remark)

i
m
{T BU9543KV
P/UP
RF+ SERVO DSP
jo
MLC9800
khj†tjsrGOX]U`Zto¡P
MCS LOGIC khj†ijrGOXU[to¡P
khj†kh{h
DAC-BCK/LRCK/MCLK/DATA khj†syjrGO[[UXro¡P

PWM
PS9850
Or PS9851

< I2S Signal Flow > < Waveform of I2S audio interface signals >

3-11
 ONE POINT REPAIR GUIDE
NO SOUND
There is no sound output by DIGITAL AUDIO AMP DAMAGE, repair the set according
to the following guide.

5-2. BY DIGITAL AUDIO AMP DAMAGE (IN ALL FUNCTIONS)

5-2-1. Solution
Please check and replace IC700, IC701(Only RAT376) on MAIN board.

5-2-2. How to troubleshoot (Countermeasure)

1) Check FL±, FR± & SW± signals from IC602 to IC700 & 701 each input function.
If no signal, check if I2S audio signals are entered to IC602.
Refer to “I2S audio signal interface” on Item 5-1.
2) Check PVDD.
If PVDD is abnormal, check the SMPS.
3) Check +12 V for driving the gate of AMP IC.
a. All the powers are normal, but if +12 V is low, there is possible for AMP IC to be damaged.
b. Remove L711, L712, L713 and L714 one by one.
When removed a inductance, if +12 V is recovered, AMP IC connected to it was damaged.
c. Replace AMP IC with a new one.
4) Check the impedance between IC700/IC701_OUT-A/OUT-B & GND.

i
a. If the impedance is 0 Ω, AMP IC must be damaged.
b. After removing the heat sink, replace it with a new one.
m
5-2-3. Service hint (Any picture / Remark)
jo
pj^WW
mySGms

•‹œŠ›ˆ•ŠŒ

pj^WX z~

< Signal check point >

3-12
 ONE POINT REPAIR GUIDE
NO SOUND
There is no sound output in the USB FUNCTION, repair the set according to the fol-
lowing guide.

5-3. IN THE USB FUNCTION

5-3-1. Solution
Please check and replace IC801 on MAIN board & IC505 on USB board.

5-3-2. How to troubleshoot (Countermeasure)

1) Check +5VU to USB board.
If the USB LED are turned on, the voltage is okay, if so not, check +5.6 V to pin4 of CN501.
2) Check USB D± from MAIN board to USB board.
a. Check USB_DN/DP signals to IC801(pin116, 117).
b. Check USB± signals from IC504 to CN501 (pin2, 3).
If there is any trouble, check the power for each IC. The power is normal but , if the signal waveform to
the IC is distorted or no signal, replace it with a new one.
3) Check if “Digital audio AMP block” on item 5-2 is normal.

5-3-3. Service hint (Any picture / Remark)

i
USB CON
REG IC
m USB
P-CTRL
-/+D

DAC_DATA
DAC_LRCK
jo
IC801 IC602
MLC9800 PS9850 AMP IC
DAC_BCK TAS5612
PWM
DAC_MCLK
kT ›–G—•Z –Gju[WX

kRG›–G—•GY –Gju[WX

< USB function signal flow > < Waveform of USB D± signal >

3-13
 ONE POINT REPAIR GUIDE
NO SOUND
There is no sound output in the AUX FUNCTION, repair the set according to the fol-
lowing guide.

5-4. IN THE AUX FUNCTION

5-4-1. Solution
Please check and replace IC401 on MAIN board.

5-4-2. How to troubleshoot (Countermeasure)

1) Check AUX_L/R signals to IC401 (Pin7, 8).
2) Check if DAC_BCK, DAC_LRCK, & DAC_MCLK are entered from IC801 to IC401.
3) Check if ADC_DATA is entered from IC401 to IC801.
If no signal, check +5 V & +3.3 V(ADC) for IC401. If is NG, replace it a new one.
4) Check the following I2S signal flow from IC801 to IC602. (Refer to Item 5-1.)
If there is any trouble, check the power for each IC. The power is normal but, if the signal waveform to
the IC is distorted or no signal, replace it with a new one.
5) Check if the digital audio AMP block is okay. Refer to “Digital Audio AMP” guide on Item 5-2.
If AMP is damaged, replace it with a new one.

5-4-3. Service hint (Any picture / Remark)

i
{T
IC401
{T
m
AUX_L/R
AUX
hkj†kh{hGG›–Gy[W`
CS5346

khj†ijr ›–Gy[W_
DAC_MCLK ADC_DATA
DAC_BCK
DAC_LRCK IC602 khj†syjr ›–Gy[W^
AMP IC
jo
IC801
MLC9800 PS9850 TAS5612
DAC_DATA PWM
DAC_MCLK
khj†tjsr ›–Gy[W]

h| †sG›–Gy[Y\ h| †yG›–Gy[Y[

< AUX function signal flow > < Signal check point >

3-14
 ONE POINT REPAIR GUIDE
NO SOUND
There is no sound output in the TUNER FUNCTION, repair the set according to the
following guide.

5-5. IN THE TUNER FUNCTION

5-5-1. Solution
Please check and replace IC401, TU100 on MAIN board.

5-5-2. How to troubleshoot (Countermeasure)

1) Check if TUNER_LR is entered from Pin1,3 of TU100 to IC401(Pin23, 24).
If no signals, Check +3.3 V for Tuner power.
Check if the Tuner control signals (CLK, DAT, CE, RST, SLT) are entered from IC102 to TU100.
If it doesn’t work, replace TUNER with a new one.
2) Check if DAC_BCK, DAC_LRCK, & DAC_MCLK are entered from IC501 to IC202.
3) Check if ADC_DATA is entered from IC401 to IC801.
If no signal, check +5 V & +3.3 V(ADC) for IC401. If is NG, replace it a new one.
4) Check the following I2S audio signal flow from IC801 to IC602. (Refer to Item 5-1.)
If there is any trouble, check the power for each IC. The power is normal but, if the signal waveform to
the IC is distorted or no signal, replace it with a new one.
5) Check if the digital audio AMP block is okay. Refer to “Digital Audio AMP” guide on Item 5-2.
If AMP is damaged, replace it with a new one.

i
m
5-5-3. Service hint (Any picture / Remark)

{T {|uly†y ›–Gj[ZW
IC401 TUNER_L/R hkj†kh{hGG›–Gy[W`
{T TUNER
CS5346
jo
khj†ijr ›–Gy[W_
DAC_MCLK ADC_DATA
DAC_BCK
DAC_LRCK IC602 AMP IC khj†syjr ›–Gy[W^
IC801
MLC9800 PS9850 TAS5612
DAC_DATA PWM
DAC_MCLK
khj†tjsr ›–Gy[W]

{|uly†s ›–Gj[Y`

< TUNER IN function signal flow > < Signal check point >

3-15
 AUDIO ELECTRICAL TROUBLESHOOTIHG GUIDE
1. POWER (SMPS)

No 3.7 VA
YES
NO
Is F901 normal? Replace F901 (Use the same fuse).
YES
NO
Is BD901 normal? Replace BD901.
YES
NO
Is TH901 normal? Replace TH901.
YES
Is Vcc
NO
(10 V ~ 18 V) supplied to Is D904 normal?
IC901 Pin7?
NO

YES Check or replace D904.

Is D922 normal?
NO

i Replace D922.
m
YES
Is there NO
about 2.5 V at Replace IC903.
IC903 Pin1?
YES
NO
Is D923 normal? Replace D923.
jo
YES
NO
Is D921 normal? Replace D921.
YES
NO
Is D924 normal? Replace D924.
YES
NO
Is D925 normal? Replace D925.
YES

Power line of I/O PCB is short.

3-16
 AUDIO ELECTRICAL TROUBLESHOOTIHG GUIDE

No PVDD
YES
NO
Is F901 normal? Replace F901 (Use the same fuse).
YES
NO
Is BD901 normal? Replace BD901.
YES
NO
Is TH901 normal? Replace TH901.

Is Vcc NO
(10 V ~ 18 V) supplied to NO
Is D905 normal?
IC902 Pin7?
YES

YES Check or replace D905.

i Is Q910 base "H"?

NO
m YES
• Check P-CTRL "H" signal from μ-COM. •
Check PC902.

Check or replace Q910.

jo
NO
Is Q902 normal? Replace Q902.
YES
NO
Is D929 normal? Replace D929.
YES

Is there about 2.5 V NO

at IC904 Pin1? Replace IC904.

YES

Power line of main PCB is short.

3-17
AUDIO ELECTRICAL TROUBLESHOOTIHG GUIDE

No 12 V

YES

Is Vcc NO
(15 V) supplied to Q953 Check or replace D921.
collector?

YES

Is the NO Check P-CTRL “H” signal

13 V Supplied to Q953
base? from μ-COM.

YES

Check or replace Q953.

i
m
No 5 V

YES
jo
Is Vcc NO
(6 V) supplied to IC951 Check or replace D923.
Pin1?

YES

Check NO Check P-CTRL

IC951 Pin4 "H". “H”’ signal from μ-COM.

YES

Check or replace IC951.

3-18
AUDIO ELECTRICAL TROUBLESHOOTIHG GUIDE

No VFD

YES

NO
Is D925 normal? Check or replace D925.

YES

NO
Is ZD951 normal? Check or replace ZD951.

YES

NO
Is Q951 normal? Check or replace Q951.

YES

Check or replace VFD.

i
m
jo

3-19
 AUDIO ELECTRICAL TROUBLESHOOTIHG GUIDE
2. μ-COM PART CHECK
μ-COM PART
CHECK
YES

Check if NO
voltage of CN105 Pin10 Refer to
SMPS troubleshooting.
is 3.7 VA.

YES

Check NO
both end voltage of Check if output of
D102, D105. D105(MBR0540) is 3.7 V.

YES
NO NO
Check if IC102_Pin49 and
IC102_Pin36,59 are 3.5 V.

i
Check D102, D105. Replace D102, D105.

YES
m
X101:32.768kHz YES
X102:9.8304MHz
Check the operation.

YES
jo
OK OK

3. IC101(S24CS16A01) CHECK
CHECK
IC102 PIN47,48
YES

NO NO
Pin47: DATA Check μ-COM Refer to μ-COM troubleshooting.
Pin48: CLK. voltage 3.5 V.

YES YES
NO
Check μ-COM. Replace μ-COM.

YES

OK OK

3-20
 AUDIO ELECTRICAL TROUBLESHOOTIHG GUIDE
4. FLD DISPLAY CHECK

FLD DISPLAY CHECK

YES

Check NO
CN104 Pin1,2,3 input Refer to SMPS troubleshooting.
voltage.

YES
Check if both end voltage
of F1,F2 are over 3.4 V
VKK : over 26 V.
YES

Check CN304
connection and power NO
Pin14,15,16(VKK,FL-,FL+), Check CN304 connection.
Pin11(3.7 VA).
YES

YES

i
Check each
m Pin voltage.

YES

OK
Check
IC501(ET6315) voltage NO
If voltage is Not 3.7 VA,
jo
Pin30 VKK:-26 V check input and output of D501.
Pin13, 43:+5 V. YES
NO
YES Check IC501. Replace IC501.

YES

Check OK
IC102->IC501
data communication NO
Pin3->Pin9 STB Check input data
Pin2->Pin7 DATA IC102 Pin2,3,4.
Pin4->Pin8 CLK YES
Check output data IC102 Pin2.
YES YES
NO
FLD light on? Check IC102. Replace IC102.

YES YES

OK OK

3-21
 AUDIO ELECTRICAL TROUBLESHOOTIHG GUIDE
5. PWM MODULATION CHECK
PWM MODULATION PART CHECK

YES

Check NO Refer to
CN105 Pin10 3.7 VA.
SMPS troubleshooting.

YES
• Check IC602(PS9850) VDD 3.3 V
(Pin16,24,29,32,35,40,48,61,64)
• Check VDD Core 1.2 V (Pin1,21,43,57,59,60)
• Check X602(19.2 MHz)
YES

Check NO NO
Check X602
X602(19.2 MHz) Replace X602(19.2 MHz).
(19.2 MHz).
operation.

YES

i
YES
m
Check
IC602(PS9850) OK
Pin51 CLK input.
jo
YES

Check
IC102(LC87Fxx) Check line
NO resistor output NO
Pin41:PWM RESET Replace R636,R637,R638.
RST: R636 / SCL: R637 /
Pin45:PWM SDA SDA: R638.
Pin46:PWM SCL
output.
YES
YES

OK

3-22
AUDIO ELECTRICAL TROUBLESHOOTIHG GUIDE

YES

Check
IC602(PS9850) NO Check NO
CD Assy communication Refer to
input data
Pin4, 5, 6. CD troubleshooting.
Pin4, 5, 6
PWM wave.
YES
YES
Check NO Check each line
IC602(PS9850) input
resistor output.
data.

YES

OK

i
m
Check
PWM
modulator output NO Check NO
FL: Pin31(+),30(-) IC602(PS9850). Replace IC602(PS9850).
FR: Pin28(+),27(-)
jo
and others.
YES

YES

OK OK

3-23
 AUDIO ELECTRICAL TROUBLESHOOTIHG GUIDE
6. POWER AMP PART CHECK

POWER AMP PART CHECK

YES

Check NO
CN105 Pin2: +12 V Refer to SMPS troubleshooting.
Pin13,15: 29 V.

YES

Check IC700, IC701

Pin30,31,38,39,42,43,50,51 input voltage.

YES

Check each IC603 NO

Check each line resistor output voltage.
Pin64:+12 V input.

YES

i
m
Check PWM Modulator input
IC700 Pin4,5,10,11 / IC701 Pin4, 5.

YES

Check IC701, IC702

jo
Pin28,29,36,37,43,44,52,53.

YES

Check output NO
Replace the coil.
line coil.

YES

OK

3-24
 AUDIO ELECTRICAL TROUBLESHOOTIHG GUIDE
7. TUNER / AUX FUNCTION CHECK

FUNCTION CHECK

YES

Check IC401 NO
(CS5346) Pin7,8, Check JK401,TU100.
23,24 input.

YES

Check IC401 NO Check IC401 NO Check CN105 Pin7: +5 V

(CS5346) Pin9 output Pin5: +5 V
Pin9,10: +3.3 V.
data. Pin46: +3.3 V.

YES YES

i
Check
m NO
Check IC401
Pin5: +5 V, NO
Check IC401
Pin41: SDOUT,
IC801(MLC9800) Pin42: SLCK,
Pin6: High,
input data. Pin43: LRCK,
Pin46: 3.3 V. Pin44: MCLK.

YES
jo
IC501(MLC9800)
output data.

YES

OK

3-25
 AUDIO ELECTRICAL TROUBLESHOOTIHG GUIDE
8. TUNER FUNCTION CHECK

TUNER FUNCTION CHECK

YES

Check tuner NO Check tuner module voltage

module(TU100)
operation. (Pin4: +3.3 V).

YES

Check IC102 Pin21, 22, 23, 24, 25

NO
data in/output. Check tuner module data.
YES

Refer to function check.

i
m
jo

3-26
 CDP ELECTRICAL TROUBLESHOOTIHG GUIDE
1. CD FUNCTION

CD FUNCTION

YES

Can the NO NO Is Motor_open/close

disc insert? Is load +,- ok? OK? (IC301 Pin10,11)
YES
YES YES
Check IC301.

NO
Is Motor ok?
Check loading motor.
(about 12 Ω)

NO Focus/ NO
NO OPU driving (Focus Check IC301
Disc reading tracking/sled signal
and tracking) is ok? (Motor drive IC).
is ok?

i is ok?

YES
m YES
NO
Is the PD(CN301 Check OPU
Is no signal at spk?
Pin12) about 180mV? (pick-up).
YES

Check
jo
the signal of NO
Check Vcc of IC302.
IC302 Pin34,35,36.

YES

Check
the signal (16.0344 MHz) NO NO Replace Cristal
Check Cristal (X301).
of IC302 (X301).
Pin31.

YES

Check IC801 NO
input/output and Replace IC801.
control line.

YES
Refer to function
check.

3-27
 CDP ELECTRICAL TROUBLESHOOTIHG GUIDE
2. USB FUNCTION

USB FUNCTION

YES

Plug-in usb device.

YES

NO NO
Display “NO USB”. Check USB_5V. Check CN401.

YES

YES

Check USB_D+/D- NO
Display “READ”. Check usb jack (JK501).
(R501,R502).

YES

i
m YES

NO
Display “NO FILE”. Check IC801(Pin116, 117). Replace IC801.

YES
jo
Check usb audio file in usb device
(MP3, WMA file is playable)

3-28
 WAVEFORMS
1. SDRAM

CLK IC802 Pin38

1
DATA
IC802 Pin53
2

ADDRESS
IC802 Pin35
3
CS
IC803 Pin1
4

i
m
2. SERVO
jo
5 IC801 Pin63

CD-16M

3-29
 FE
6 IC302 Pin61

TE
7 IC302 Pin62
FOD
8 IC302 Pin13
RF
IC302 Pin63
9

i
m
3. AUDIO PATH
jo
IC801 Pin100
10
CD_BCK
IC801 Pin102
CD_LRCK
11

CD_DATA
12 IC801 Pin101

3-30
 DAC_MCK
IC801 Pin86
13

DAC_BCK
14 IC801 Pin87

DAC_LRCK IC801 Pin88

15

DAC_DATA
IC801 Pin83
16

i
m
4. USB
jo
USB_5V

17
D+ IC801 Pin116

D- IC801 Pin117
18

3-31
WIRING DIAGRAM

(CDM-345)

i
m
CN301

CN303

CN901

jo
CN902
CN903
6PIN
CN105

CN401
CN104

CN304
CN302

CN502

CN501

3-33 3-34
BLOCK DIAGRAMS
1. OVERALL BLOCK DIAGRAM
16.93MHZ
12.288MHZ
A,B,C,D,E,F
DECK MECHANISM L
PD BU9543KV FL+
DAC-BCK/LRCK/MCLK
LD
RF+ SERVO DSP FL- AMP
PWM TAS5612
FDO DAC-DATA FR+
P/UP TDO PS9850 R
SLEDs
s,Fs,Ts

CD-BCK/ LRCK/ DOUTA

SUBSYQ; BUSY; CD-16M
SLDO FR-
SPDO

CD_MCK/ CD_R/W

DAC-MCLK
9543-RST;
CD_DIN_DOUT

PWM-DAT
PWM-RST

PWM-CLK
SPINDLEs
M
AM5890S

SD; OTW
LOAD
MOTOR
s EEPROM

PDN
IC

i
DAT
9.8304MHZ

CLK
m
OP/CL
SPI-DO/DI/CLK/ CS
RESET; MU
TE I2S CLK ADC-RST
OP/CL LI MIT MLC9800 MICOM

32.766khz
ADC-DAT
CS5346
LC87F5M64A

SDRAM
EM638165TS-6G
DSCK#,CKE,CS0#,RAS0#
DMA[0..11],DB[0..15]
jo
MCS LOGIC

ADC-DATA
ADC(6CH) ADC-CLK

DAT, CLK, RST, CE, INT

A[0.. 18], DB[0..15]

P-SENSE
RST, WEN#,CE#

STB

CLK

DO
R/L

R/L
P-CTRL

12MHZ
D+/-

VFD DRIVER
ET6315
FLASH KEY RMC
MX25LB005BMC
VFD Standby LED
USB CON
AUX TUNER +12V POWER
REG IC
I/F
VOLUME LED 3.7V

3-35 3-36
2. SMPS BLOCK DIAGRAM
SMPS
On/Off FL+
‫م‬ ‫م‬
Snubber
Block FL-
ࣧ
Vkk
CN901
On/Off
‫م‬ ‫م‬
T ‫م‬ 5V LDO 5V
R 5.6VA
Main A
SMPS IC 12V 12V
‫م‬ N CN902/3
Block Regulation
S On/Off
Block

i
3.7VA

m
‫م‬
‫م‬

Noise Y-Cap Feedback

Filter
Photo coupler CD P.CTL
Block
(X-cap
Line Filter)

F
U
Y-Cap
jo ‫م‬
Snubber
Block

‫م‬
On/Off

T
R
A
Photo coupler ‫م‬ ‫م‬ P.CTL

S
E AMP N
SMPS IC PVDD
S ‫م‬

With FET
Feedback
‫م‬ Block
Photo coupler

3-37 3-38
 IMPORTANT SAFETY NOTICE COMPONENTS ARE SHADED ON THE SCHEMATIC NOTE :

CIRCUIT DIAGRAMS WHEN SERVICING THIS CHASSIS, UNDER NO

CIRCUMSTANCES SHOULD THE ORIGINAL DESIGN BE
FOR EASY IDENTIFICATION.
THIS CIRCUIT DIAGRAM MAY OCCASIONALLY DIFFER
FROM THE ACTUAL CIRCUIT USED. THIS WAY,
1. Shaded( ) parts are critical for safety.
Replace only with specified part number.
2. Voltages are DC-measured with a digital voltmeter
1. SMPS CIRCUIT DIAGRAM MODIFIED OR ALTERED WITHOUT PERMISSION
FROM THE LG CORPORATION. ALL COMPONENTS
IMPLEMENTATION OF THE LATEST SAFETY AND
PERFORMANCE IMPROVEMENT CHANGES INTO
during Play mode.
SHOULD BE REPLACED ONLY WITH TYPES IDENTICAL THE SET IS NOT DELAYED UNTIL THE NEW SERVICE
TO THOSE IN THE ORIGINAL CIRCUIT. SPECIAL LITERATURE IS PRINTED.

12

11

10

i
8

m
7

3
jo
2

CAUTION:
Danger if fuse is incorrectly replaced.
Replace only with the type identical to fuse rating Warning
1
and(or) model name described in main label. Parts that are shaded are critical with
respect to risk of fire or electrical shock. SMPS
EBY60749101 Rev 7.1
2010.11.09
A B C D E F G H I J K L M N O P Q R S T

3-39 3-40
2. MICOM & AD CIRCUIT DIAGRAM

12

11

10

i
8

m
7

3
jo
2

1
µ-COM & AD
EBY61070801(#1) Rev 1.9
2010.11.09
A B C D E F G H I J K L M N O P Q R S T

3-41 3-42
3. PWM & AMP CIRCUIT DIAGRAM

12

11

10

i
8

m
7

3
jo
2

1
PWM & AMP
EBY61070801(#2) Rev 1.9
2010.11.09
A B C D E F G H I J K L M N O P Q R S T

3-43 3-44
4. CD DSP & SERVO CIRCUIT DIAGRAM

12

11

10
9 7 6 5

i
8

m
16
1
13
7
3
14
15

6 10 12 11 17 18

3
jo 4

1
: WAVEFORM NUMBER CD DSP & SERVO
EBY61070801(#3) Rev 1.9
2010.11.09
A B C D E F G H I J K L M N O P Q R S T

3-45 3-46
5. FRONT CIRCUIT DIAGRAM

12

11

10

i
8

m
7

3
jo
2

1
FRONT
EBY61070901 Rev 2.2
2010.11.09
A B C D E F G H I J K L M N O P Q R S T

3-47 3-48
6. USB CIRCUIT DIAGRAM

12

11

10

i
8

m
7

3
jo
2

1
USB
EBY61071001 Rev 1.5
2010.11.09
A B C D E F G H I J K L M N O P Q R S T

3-49 3-50
CIRCUIT VOLTAGE CHART

1. SMPS Board
P.OFF(STANBY) P.ON (Unloaded) CD_PLAY (USB insert) Location Pin No. Specification EE Mode (V) Margin Playback Mode (V) Margin
Location Cap Mode Voltage Current Voltage Current Voltage Current 43 (VDD_CORE) 1.08~1.32 1.24 0.08 1.24 0.08
(V) (mA) (V) (mA) (V) (mA)
48 (VDD_IO) 2.97~3.63 3.22 0.41 3.22 0.41
3.7VA C923 330uF/16 3.70 40 3.70 200 3.70 220
57 (VDD_CORE) 1.08~1.32 1.24 0.08 1.24 0.08
5.0V(Main) C951 100uF/16 0 0 5.0 40 5.0 200
59 (VDDA) 1.08~1.32 1.24 0.08 1.24 0.08
F+ - - -24 0 -19 132 -19.0 136
61 (VDD_VIN2) 2.20~3.30 3.22 0.08 3.22 0.08
F- C952 - -24 0 -23.5 130 -23.5 130
64 (VDD_VIN1) 2.20~3.30 3.22 0.08 3.22 0.08
VKK C926 47u/50 -26 10 -26.5 10 -26 10
IC700 AMP (TAS5612)
12V C921 100/50 0 0 12 100 12 115
56 (GVDD_B) 10.8~13.2 11.6 1.6 11.6 1.06
PVDD C932 1000/35 0 0 21.5 600 21.5 600
64 (VDD) 10.8~13.2 11.7 1.5 11.7 1.07
25 (GVDD_C) 10.8~13.2 11.7 1.03 11.7 1.06
2. MAIN Board 26 (GVDD_D) 10.8~13.2 11.7 1.03 11.7 1.06
30 (PVDD_D) 0~34 21.5 12.1 21.5 12.1
Location Pin No. Specification EE Mode (V) Margin Playback Mode (V) Margin
31 (PVDD_D) 0~34 21.5 12.1 21.5 12.1
IC101 EEPROM (M24C16)
39 (PVDD_C) 0~34 21.5 12.1 21.5 12.1
8 (VCC) 1.8~5.5 3.4 2.1 3.4 2.1
42 (PVDD_B) 0~34 21.5 12.1 21.5 12.1

i
IC102 MICOM (LC87F5M64A)
50 (PVDD_A) 0~34 21.5 12.1 21.5 12.1
9 (VDD2) 2.8~5.5 3.4 0.6 3.4 0.6
51 (PVDD_A) 0~34 21.5 12.1 21.5 12.1

m
36 (VDD3) 2.8~5.5 3.4 0.6 3.4 0.6
55 (GVDD_A) 10.8~13.2 11.7 1.03 11.7 1.06
59(VDD1) 2.8~5.5 3.4 0.6 3.4 0.6
IC801 (MLC9800)
IC301 MOTOR IC
2 (AVDD33) 2.97~3.63 3.2 0.43 3.2 0.43
8 (VCC1) 4.3~13.2 4.95 0.65 4.93 0.63
13 (VDD12) 1.08~1.32 1.2 0.12 1.1 0.22
19 (VCC2) 4.3~Vcc1 4.95 0.65 4.93 0.63
30 (IOVDD33) 2.97~3.63 3.2 0.43 3.2 0.43
IC302 SERVO (BU9543KV)
47 (VDD12) 1.08~1.32 1.2 0.12 1.1 0.22
1 (AVDD1) 2.7~3.6 3.24 0.36 3.24 0.36
51 (IOVDD33) 2.97~3.63 3.2 0.43 3.2 0.43
17 (DVDD) 2.7~3.6 3.24 0.36 3.24 0.36
33 (DVDD)
26 (VDD_CORE)
37 (VDD_CORE)
47 (DVDD)
53 (DVDD2)
58 (AVDD2)

5 (VLC)
14 (VA)
30 (VA)
2.7~3.6
1.35~1.65
1.35~1.65
2.7~3.6
2.7~3.6
2.7~3.6

3.13~5.25
4.75~5.25
4.75~5.25
3.24
1.56
1.56
3.24
3.24
3.24

4.94
4.94
4.94
IC401 ADC (CS5346)
0.36
0.09
0.09
0.36
0.36
0.36

0.31
0.31
0.31
jo 3.24
1.56
1.56
3.24
3.24
3.24

4.94
4.94
4.94
0.36
0.09
0.09
0.36
0.36
0.36

0.31
0.31
0.31
84 (IOVDD33)
94 (VDD12)
113 (IOVDD33)
115 (USBVDD33)
120 (PLL1VDD12)
122 (PLL3VDD12)
124 (PLL2VDD12)

1 (VDD)
3 (VDDQ)
2.97~3.63
1.08~1.32
2.97~3.63
2.97~3.63
1.08~1.32
1.08~1.32
1.08~1.32

3.0~3.6
3.0~3.6
3.2
1.2
3.2
3.2
1.2
1.2
1.2

3.2
3.2
IC802 SDRAM
0.43
0.12
0.43
0.43
0.12
0.12
0.12

0.4
0.4
3.2
1.2
3.2
3.2
1.2
1.2
1.2

3.26
3.26
0.43
0.12
0.43
0.43
0.12
0.12
0.12

0.34
0.34
9 (VDDQ) 3.0~3.6 3.2 0.4 3.26 0.34
36 (VLS) 3.13~5.25 3.24 2.01 3.24 2.01
14 (VDD) 3.0~3.6 3.2 0.4 3.26 0.34
46 (VD) 3.13~3.47 3.24 0.23 3.24 0.23
27 (VDD) 3.0~3.6 3.2 0.4 3.26 0.34
IC602 PWM (PS9850)
43 (VDDQ) 3.0~3.6 3.2 0.4 3.26 0.34
16 (VDD_IO) 2.97~3.63 3.23 0.4 3.23 0.4
49 (VDDQ) 3.0~3.6 3.2 0.4 3.26 0.34
21 (VDD_CORE) 1.08~1.32 1.24 0.08 1.24 0.08
IC803 Flash
24 (VDD_IO) 2.97~3.63 3.22 0.41 3.22 0.41
8 (VDD) 2.7~3.6 3.2 0.4 3.2 0.4
29 (VDD_IO) 2.97~3.63 3.22 0.41 3.22 0.41
32 (VDD_IO) 2.97~3.63 3.22 0.41 3.22 0.41
35 (VDD_IO) 2.97~3.63 3.24 0.39 3.24 0.39
40 (VDD_IO) 2.97~3.63 3.24 0.39 3.24 0.39

3-51 3-52
 MEMO

Location Value EEMode Play back Rec voltage

No. (uF) Spec (+) (-) Gap Margin (+) (-) Gap Margin (+) (-) Gap Margin
C118 1000uF 6.3V 3.5V 0V 3.5V 2.8V 3.44V 0V 3.44V 2.86V 3.39V 0V 3.39V 2.91V
C302 100uF 16V 0.22V 0V 0.22V 15.78V 3.31 0V 3.31 12.69V 3.26 0.03 3.23V 12.77V
C304 100uF 16V 0V 0V 0V 16V 1.65V 0V 1.65V 14.35V 1.64 0.03 1.61V 14.39V
C311 47uF 16V 0.22V 0.13V 0.09V 15.78V 3.17V 2.44V 0.73V 12.83V 3.1 2.37 0.73V 15.27V
C313 100nF 50V 0V 0V 0V 50V 4.97V 0V 4.97V 45.03V 4.92 0 4.92V 45.08V
C317 100uF 6.3V 0V 0V 0V 6.3V 1.57V 0V 1.57V 4.73V 1.57 0 1.57V 4.73V
C326 100uF 16V 0V 0V 0V 16V 4.97V 0V 4.97V 11.03V 4.92 0 4.92V 11.08V
C336 3.3uF 50V 0V 0V 0V 50V 1.65V 1.65V 0V 48.35V 1.65 1.64 0.01V 49.99V
C338 47uF 16V 0.22V 0V 0.22V 15.78V 3.31 0V 3.31 12.69V 3.25 0.03 3.22V 12.78V
C347 100uF 16V 0.11V 0V 0.11V 15.89V 1.65V 0V 1.65V 14.35V 1.64 0.03 1.61V 14.39V
C357 47uF 16V 0.22V 0V 0.22V 15.78V 3.31V 0V 3.31V 12.69V 3.25 0.03 3.22V 12.78V
C406 47uF 16V 0.22V 0V 0.22V 15.78V 3.31V 0V 3.31V 12.69V 3.26 0 3.26V 12.74V
C408 100uF 16V 0V 0V 0V 16V 2.49V 0V 2.49V 13.51V 0 0 0V 16V
C410 47uF 16V 0.24V 0V 0.24V 15.76V 4.97V 0V 4.97V 11.03V 3.65 0 3.65V 12.35V

i
C423 47uF 16V 0V 0V 0V 16V 4.02V 0V 4.02V 11.98V 1.41 0 1.41V 14.59V
C613 10uF 16V 0V 0V 0V 16V 1.25V 0V 1.25V 14.75V 1.24 0 1.24V 14.76V
C6A0 470uF 10V 0V 0V 0V 10V 1.25V 0V 1.25V 8.75V 1.24 0 1.24V 8.76V

m
C6A1 100pF 50V 0.18V 0V 0.18V 49.82V 1.65V 0V 1.65V 48.35V 3.25 0 3.25V 46.75V
C825 47uF 16V 0.2V 0V 0.2V 15.8V 3.31V 0V 3.31V 12.69V 3.26 0 3.26V 12.74V
C827 47uF 16V 0V 0V 0V 16V 1.19V 0V 1.19V 14.81V 1.18V 0V 1.18V 14.82V
C828 47uF 16V 0.2V 0V 0.2V 15.8V 3.31V 0V 3.31V 12.69V 3.26V 0V 3.26V 12.74V
C848 47uF 16V 0V 0V 0V 16V 1.19V 0V 1.19V 14.81V 1.18V 0V 1.18V 14.82V
C849 100nF 50V 0.22V 0V 0.22V 49.78V 3.32V 0V 3.32V 46.68V 3.26V 0V 3.26V 46.74V
C8F6 47uF 16V 0.2V 0V 0.2V 15.8V 3.31V 0V 3.31V 12.69V 3.26 0 3.26V 12.74V
C8F7 47uF

3. FRONT Board
Location Pin No.

13 (VDD)
43 (VDD)
30 (VEE)
16V 0V

Specification

4.5~5.5
4.5~5.5
VDD-35
0V 0V

EE Mode (V)

3.5
3.5
-25.8
16V 1.19V

IC501 VFD (ET6315)

0V

Margin

-1
-1
9.2
jo
1.19V 14.81V 1.18

Playback Mode (V)

3.48
3.48
-25.5
0 1.18V

Margin

-1.02
-1.02
9.5
14.82V

Value EE Mode Playback Rec voltage

Location No. Spec
(uF) (+) (-) Gap Margin (+) (-) Gap Margin (+) (-) Gap Margin

C510 47uF 16V 3.5V 0V 3.5V 12.5V 3.5V 0V 3.5V 12.5V 3.4V 0V 3.4V 12.6V
C514 47uF 35V 0V -25.9V 25.9V 9.1V 0V -25V 25V 10V 0V -24.2V 24.2V 10.8V
C516 100uF 16V 3.6V 0V 3.6V 12.4V 3.6V 0V 3.6V 12.4V 3.6V 0V 3.6V 12.4V
C549 47uF 16V 6.2V 0V 6.2V 9.8V 6.1V 0V 6.1V 9.9V 5.7V 0V 5.7V 10.3V
C551 100uF 16V 5V 0V 5V 11V 5V 0V 5V 11V 5V 0V 5V 11V

3-53 3-54