E&H Transmitter

Operating Instructions
Cerabar S PMC71, PMP71/72/75

Pressure transmitter
BA271P/00/en/11.05
71009589
valid from
Software version 02.01
Hardware version 02.00
Overview documentation Cerabar S PMC71, PMP71/72/75 with 4...20 mA HART
Overview documentation
Device Documentation Content Remarks
Cerabar S 4...20 mA HART Technical Information TI383P Technical data – The documentation is located on the ToF Tool
CD. The CD is enclosed with every device
ordered with the "HistoROM/M-DAT"
option. The "HistoROM/M-DAT" option is
selected in the order code via feature 100
Additional option 1" or 110 "Additional
option 2", version "N".
– The documentation is also available via the
Internet. → See: www.endress.com →
Download
Operating Instructions BA271P – Identification – The documentation is supplied with the

– Installation device.
– Wiring – The documentation is also available via the
– Operation Internet. → See: www.endress.com →
– Commissioning, Description of Download
Quick Setup menus
– Maintenance
– Trouble-shooting and spare parts
– Appendix: Illustration of menu
Operating Instructions BA274P – Examples of configuration for – The documentation is located on the ToF Tool
pressure and level measurement CD. The CD is enclosed with every device
– Description of parameters ordered with the "HistoROM/M-DAT"
– ’Trouble-shooting option. The "HistoROM/M-DAT" option is
– Appendix: Illustration of menu selected in the order code via feature 100
Additional option 1" or 110 "Additional
option 2", version "N".
– The documentation is also available via the
Internet. → See: www.endress.com →
Download
Brief Operating Instructions KA218P – Wiring – The documentation is supplied with the
– Operation without on-site device. See cover of the terminal
display compartment.
– Description of Quick Setup menus
– Operation HistoROM®/M-DAT
Functional Safety Manual SD190P – Safety function with Cerabar S – The documentation is supplied with the
– Behaviour in operation and failure devices showing version "E" in feature 100
– Commissioning and iterative tests "Additional options 1" or in feature 110
– Settings "Additional options 2".
– Technical safety characteristic → See also Technical Information TI383P,
quantities chapter "Ordering information".
– Management Summary
2 Endress+Hauser
Cerabar S PMC71, PMP71/72/75 with 4...20 mA HART Table of contents
Table of contents
1 Safety instructions . . . . . . . . . . . . . . . . 4 8 Trouble-shooting . . . . . . . . . . . . . . . . . 46
1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 8.1 Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
1.2 Installation, commissioning and operation . . . . . . . . 4 8.2 Response of outputs to errors . . . . . . . . . . . . . . . . . 53
1.3 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . 4 8.3 Confirming messages . . . . . . . . . . . . . . . . . . . . . . . 54
1.4 Notes on safety conventions and icons . . . . . . . . . . . 5 8.4 Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
8.5 Repair of Ex-certified devices . . . . . . . . . . . . . . . . . 55
2 Identification . . . . . . . . . . . . . . . . . . . . 6 8.6 Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
8.7 Returning the device . . . . . . . . . . . . . . . . . . . . . . . 65
2.1 Device designation . . . . . . . . . . . . . . . . . . . . . . . . . 6 8.8 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
2.2 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 8.9 Software history . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
2.3 CE mark, declaration of conformity . . . . . . . . . . . . . 7
2.4 Registered trademarks . . . . . . . . . . . . . . . . . . . . . . . 7
9 Technical data . . . . . . . . . . . . . . . . . . . 67
3 Installation . . . . . . . . . . . . . . . . . . . . . . 8
10 Appendix . . . . . . . . . . . . . . . . . . . . . . . 67
3.1 Incoming acceptance and storage . . . . . . . . . . . . . . . 8
3.2 Installation conditions . . . . . . . . . . . . . . . . . . . . . . . 8 10.1 Operating menu for on-site display, ToF Tool,
3.3 Installation instructions . . . . . . . . . . . . . . . . . . . . . . 8 FieldCare and HART handheld terminal . . . . . . . . . 67
3.4 Post-installation check . . . . . . . . . . . . . . . . . . . . . . 15 10.2 Operating matrix HART Commuwin II . . . . . . . . . . 73
10.3 Patents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . 15
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
4.1 Connecting the device . . . . . . . . . . . . . . . . . . . . . . 15
4.2 Connecting the measuring unit . . . . . . . . . . . . . . . 17
4.3 Potential matching . . . . . . . . . . . . . . . . . . . . . . . . 20
4.4 Overvoltage protection (optional) . . . . . . . . . . . . . . 20
4.5 Post-connection check . . . . . . . . . . . . . . . . . . . . . . 20
5 Operation . . . . . . . . . . . . . . . . . . . . . . 21
5.1 On-site display (optional) . . . . . . . . . . . . . . . . . . . . 21
5.2 Operating elements . . . . . . . . . . . . . . . . . . . . . . . . 22
5.3 On-site operation –
on-site display not connected . . . . . . . . . . . . . . . . . 26
on-site display connected . . . . . . . . . . . . . . . . . . . . 28
5.5 HistoROM®/M-DAT (optional) . . . . . . . . . . . . . . 30
5.6 Operation via HART handheld terminal . . . . . . . . . 33
5.7 ToF Tool operating program . . . . . . . . . . . . . . . . . 34
5.8 FieldCare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
5.9 Commuwin II operating program . . . . . . . . . . . . . . 35
5.10 Locking/unlocking operation . . . . . . . . . . . . . . . . . 36
5.11 Factory setting (reset) . . . . . . . . . . . . . . . . . . . . . . 37
6 Commissioning. . . . . . . . . . . . . . . . . . 39
6.1 Function check . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
6.2 Selecting language and measuring mode . . . . . . . . 39
6.3 Position adjustment . . . . . . . . . . . . . . . . . . . . . . . . 40
6.4 Pressure measurement . . . . . . . . . . . . . . . . . . . . . . 41
6.5 Level measurement . . . . . . . . . . . . . . . . . . . . . . . . 43
7 Maintenance. . . . . . . . . . . . . . . . . . . . 46
7.1 Exterior cleaning . . . . . . . . . . . . . . . . . . . . . . . . . 46
Endress+Hauser 3
Safety instructions Cerabar S PMC71, PMP71/72/75 with 4...20 mA HART
1 Safety instructions
1.1 Designated use

The Cerabar S is a pressure transmitter for measuring pressure and level.
The manufacturer accepts no liability for damages resulting from incorrect use or use other than that
designated.
1.2 Installation, commissioning and operation

The device has been designed to operate safely in accordance with current technical, safety and EU
standards. If installed incorrectly or used for applications for which it is not intended, however, it is
possible that application-related dangers may arise, e.g. product overflow due to incorrect
installation or calibration. For this reason, the instrument must be installed, connected, operated
and maintained according to the instructions in this manual: personnel must be authorised and
suitably qualified. The manual must have been read and understood, and the instructions followed.
Modifications and repairs to the device are permissible only when they are expressly approved in
the manual. Pay particular attention to the technical data on the nameplate.
1.3 Operational safety
1.3.1 Hazardous areas (optional)

Devices for use in hazardous areas are fitted with an additional nameplate (→ see Page 6). If the
device is to be installed in an explosion hazardous area, then the specifications in the certificate as
well as all national and local regulations must be observed. A separate Ex documentation is enclosed
with the device and is an integral part of this documentation. The installation regulations,
connection values and Safety Instructions listed in this document must be observed. The
documentation number of the related Safety Instructions (XA...) is also indicated on the additional
nameplate.
• Ensure that all personnel are suitably qualified.
1.3.2 Functional Safety SIL 2 (optional)

If using devices for SIL 2 applications, the separate manual on functional safety (SD190P) must be
observed thoroughly.
4 Endress+Hauser
Cerabar S PMC71, PMP71/72/75 with 4...20 mA HART Safety instructions
1.4 Notes on safety conventions and icons

In order to highlight safety-relevant or alternative operating procedures in the manual, the following
conventions have been used, each indicated by a corresponding icon in the margin.
Symbol Meaning
#
Warning!
A warning highlights actions or procedures which, if not performed correctly, will lead to
personal injury, a safety hazard or destruction of the instrument.
"
Caution!
Caution highlights actions or procedures which, if not performed correctly, may lead to
personal injury or incorrect functioning of the instrument.
!
Note!
A note highlights actions or procedures which, if not performed correctly, may indirectly
affect operation or may lead to an instrument response which is not planned.
0
Device certified for use in explosion hazardous area
If the device has this symbol embossed on its nameplate, it can be installed in an explosion
hazardous area or a non-explosion hazardous area, according to the approval.
Explosion hazardous area
- Symbol used in drawings to indicate explosion hazardous areas.

– Devices used in hazardous areas must possess an appropriate type of protection.
Safe area (non-explosion hazardous area)
. Symbol used in drawings to indicate, if necessary, non-explosion hazardous areas.

– Devices used in hazardous areas must possess an appropriate type of protection. Lines
used in hazardous areas must meet the necessary safety-related characteristic quantities.
% Direct voltage
A terminal to which or from which a direct current or voltage may be applied or supplied.
&
Alternating voltage
A terminal to which or from which an alternating (sine-wave) current or voltage may be
applied or supplied.
)
Grounded terminal
A grounded terminal, which as far as the operator is concerned, is already grounded by
means of an earth grounding system.
*
Protective grounding (earth) terminal
A terminal which must be connected to earth ground prior to making any other connection
to the equipment.
+
Equipotential connection (earth bonding)
A connection made to the plant grounding system which may be of type e.g. neutral star or
equipotential line according to national or company practice.
Endress+Hauser 5
Identification Cerabar S PMC71, PMP71/72/75 with 4...20 mA HART
2 Identification
2.1 Device designation
2.1.1 Nameplate
Cerabar S
Order Code: 1
3
D-79689 Maulburg
Ser.-No.: 2
Made in Germany,
5
MWP 4 Span 6
P 7
8 U= 9 12
Mat. 10
11
13 14 14
15
P01-PMx7xxxx-18-xx-xx-xx-001
Fig. 1: Nameplate for Cerabar S

1 Order code
See the specifications on the order confirmation for the meanings of the individual letters and digits.
2 Serial number
3 Degree of protection
4 MWP (Maximum working pressure)
5 Symbol: Note: pay particular attention to the data in the "Technical Information"!
6 Minimum/maximum span
7 Nominal measuring range
8 Electronic version (output signal)
9 Supply voltage
10 Wetted materials
11 ID number of notified body with regard to Pressure Equipment Directive (optional)
12 ID number of notified body with regard to ATEX (optional)
13 GL-symbol for GL marine certificate (optional)
14 SIL-symbol for devices with SIL2/ 61508 Declaration of conformity (optional)
15 Layout identification of the nameplate
Devices for use in hazardous areas are fitted with an additional nameplate.
1
2
4 5 Dat.: 6
P01-xMD7xxxx-18-xx-xx-xx-002
Fig. 2: Additional nameplate for devices for hazardous areas

1 EC type examination certificate number
2 Type of protection e.g. II 1/2 G EEx ia IIC T4/T6
3 Electrical data
4 Safety Instructions number e.g. XA 235-P
5 Safety Instructions index e.g. A
6 Device manufacture data (month and year)
6 Endress+Hauser
Cerabar S PMC71, PMP71/72/75 with 4...20 mA HART Identification
! Note!
• The MWP (maximum working pressure) is specified on the nameplate. This value refers to a
reference temperature of 20°C (68°F) or 100°F for ANSI flanges.
• The pressure values permitted at higher temperatures can be found in the following standards:
– EN 1092-1: 2001 Tab. 18 1
– ASME B 16.5a – 1998 Tab. 2-2.2 F316
– ASME B 16.5a – 1998 Tab. 2.3.8 N10276
– JIS B 2220
• The test pressure corresponds to the over pressure limit (OPL) of the device = MWP x 1.5.
• The Pressure Equipment Directive (EC Directive 97/23/EC) uses the abbreviation "PS". The
abbreviation "PS" corresponds to the MWP (maximum working pressure) of the measuring
device.
1) With regard to its stability-temperature property, the material 1.4435 is identical to 1.4404 which is grouped under
13EO in EN 1092-1 Tab. 18. The chemical composition of the two materials can be identical.
2.2 Scope of delivery

The scope of delivery comprises:
• Cerabar S pressure transmitter
• For devices with the "HistoROM/M-DAT" option:
CD-ROM with ToF Tool operating program and documentation
• Optional accessories
Documentation supplied:
• Operating Instructions BA271P (this document)
• Brief Operating Instructions KA218P
• Final inspection report
• Optional: factory calibration form and/or Safety Manual SD190P
• Devices which are suitable for use in hazardous areas:
additional documentation such as Safety Instructions (XA...), Control or
Installation Drawings (ZD...)
Additional documentation available with devices with the "HistoROM/M-DAT" option:
• Technical Information TI383P
2.3 CE mark, declaration of conformity

The device is designed to meet state-of-the-art safety requirements, has been tested and left the
factory in a condition in which it is safe to operate. The device complies with the applicable
standards and regulations as listed in the EC declaration of conformity and thus complies with the
statutory requirements of the EC Directives. Endress+Hauser confirms the successful testing of the
device by affixing to it the CE mark.
2.4 Registered trademarks
KALREZ, VITON, TEFLON

Registered trademarks of E.I. Du Pont de Nemours & Co., Wilmington, USA
TRI-CLAMP
Registered trademark of Ladish & Co., Inc., Kenosha, USA
HART
Registered trademark of the HART Communication Foundation, Austin, USA.
Endress+Hauser 7
Installation Cerabar S PMC71, PMP71/72/75 with 4...20 mA HART
3 Installation
3.1 Incoming acceptance and storage
3.1.1 Incoming acceptance

• Check the packaging and the contents for damage.
• Check the shipment, make sure nothing is missing and that the scope of supply matches your
order.
3.1.2 Storage
The device must be stored in a dry, clean area and protected against damage from impact
(EN 837-2).
Storage temperature range:
• –40...+100°C (–40...+212°F)
• On-site display: –40...+85°C (–40...+185°F)
3.2 Installation conditions
3.2.1 Dimensions
→ For dimensions, please refer to the Technical Information for Cerabar S TI383P, "Mechanical
construction" section. See page 2, "Overview documentation".
3.3 Installation instructions

! Note!
• Due to the orientation of the Cerabar S, there may be a shift in the measured value, i.e. when the
container is empty, the measured value does not display zero. This zero point shift can be
corrected. → See page 40, section 6.3 "Position adjustment".
• For PMP75, please refer to section 3.3.2 "Installation instructions for devices with diaphragm
seals – PMP75", page 11.
• To ensure optimal readability of the on-site display, it is possible to rotate the housing up to 380°.
→ See page 14, section 3.3.5 "Rotating the housing".
• Endress+Hauser offers a mounting bracket for installing on pipes or walls. → See page 13, section
3.3.4 "Wall and pipe mounting".
3.3.1 Installation instructions for devices without diaphragm seals –

PMP71, PMP72, PMC71
! Note!
• Cerabar S without diaphragm seal are mounted as per the norms for a manometer
(DIN EN 839-2). We recommend the use of shut-off devices an siphons. The orientation depends
on the measuring application.
• Do not clean or touch diaphragm seals with hard or pointed objects.
8 Endress+Hauser
Cerabar S PMC71, PMP71/72/75 with 4...20 mA HART Installation
Pressure measurement in gases
Fig. 3: Measuring arrangement for pressure measurement in gases

1 Cerabar S
2 Shut-off device
• Mount Cerabar S with shut-off device above the tapping point so that the condensate can flow
into the process.
Pressure measurement in steams
➀ ➃
➁ ➁
➂ ➀
Fig. 4: Measuring arrangement for pressure measurement in steams

1 Cerabar S
2 Shut-off device
3 U-shaped siphon
4 Circular siphon
• Mount Cerabar S with siphon below the tapping point.

The siphon reduces the temperature to almost ambient temperature.
• Fill the siphon with fill fluid before commissioning.
Endress+Hauser 9
Pressure measurement in liquids
Fig. 5: Measuring arrangement for pressure measurement in liquids

1 Cerabar S
2 Shut-off device
• Mount Cerabar S with shut-off device below or at the same level as the tapping point.
Level measurement
P01-PMP75xxx-11-xx-xx-xx-000
Fig. 6: Measuring arrangement for level
• Mount Cerabar S below the lowest measuring point.

• Do not mount the device at the following positions:
In the fill flow, in the tank outlet or at a point in the container which could be affected by pressure
pulses from the agitator.
• The calibration and functional test can be carried out more easily if you mount the device after a
shut-off device.
PVDF adapter
! Note!
For instruments with PVDF adapter, a maximum torque of 7 Nm is permitted. The thread
connection may become loose at high temperatures and pressures. This means that the integrity of
the thread must be checked regularly and may need to be tightened using the torque given above.
Teflon tape is recommended for sealing with the 1/2 NPT thread.
10 Endress+Hauser
3.3.2 Installation instructions for devices with diaphragm seals –

PMP75
! Note!
• The Cerabar S with diaphragm seal is screwed in, flanged or clamped, depending on the type of
diaphragm seal.
• The diaphragm seal and the pressure sensor together form a closed an calibrated system which is
filled with filling fluid through a hole in the upper part. This hole is sealed and not to be opened.
• Do not clean or touch diaphragm seals with hard or pointed objects.
• Do not remove membrane protection until shortly before installation.
• When using a mounting bracket, sufficient strain relief must be ensured for the capillaries in order
to prevent the capillary bending down (bending radius ≥ 100 mm).
• Please note that the hydrostatic pressure of the liquid columns in the capillaries can cause zero
point shift. The zero point shift can be corrected. → See also page 40, section 6.3 "Position
adjustment".
• Please note the application limits of the diaphragm seal filling oil as detailed in the Technical
Information for Cerabar S TI383P, Section "Planning instructions for diaphragm seal systems". →
See also page 2, "Overview documentation".
In order to obtain more precise measurement results and to avoid a defect in the device, mount the
capillaries as follows:
• vibration-free (in order to avoid additional pressure fluctuations)
• not in the vicinity of heating or cooling lines
• insulate in the event of colder or warmer ambient conditions
• with a bending radius of ≥100 mm.
Vacuum application
For applications under vacuum, Endress+Hauser recommends mounting the pressure transmitter
underneath the diaphragm seal. A vacuum load of the diaphragm seal caused by the presence of
filling oil in the capillaries is hereby prevented.
When the pressure transmitter is mounted above the diaphragm seal, the maximum height
difference H1 in accordance with the illustration below on the left must not be exceeded. The
maximum height difference is dependent on the density of the filling oil and the smallest ever
pressure that is permitted to occur at the diaphragm seal (empty container), see illustration below,
on the right.
FIELD TERMINALS
12.0
Vegetable oil
10.0
Height difference H1 [m]
Silicone oil
8.0
6.0
High temperature
H1 oil
4.0
Inert oil
2.0
0.0
50 100 200 300 400 500 600 700 800 900 1000
Pressure at diaphragm seal [mbarabs]
P01-PMx7xxxx-11-xx-xx-xx-008 P01-PMx7xxxx-05-xx-xx-xx-011
Fig. 7: Installation above the diaphragm Fig. 8: Diagram of maximum installation height above the
seal diaphragm seal for vacuum applications dependent on
the pressure at the diaphragm seal
Endress+Hauser 11
Mounting with temperature separator
max. 115
Endress+Hauser recommends the use of temperature separators in the event of constant extreme
fluid temperatures which lead to the maximum permissible electronics temperature of +85°C
(+185°F) being exceeded.
The additional installation height also brings about a zero point shift of approx. 21 mbar due to the
hydrostatic columns in the temperature separator. You can correct this zero point shift. → See also
page 40, section 6.3 "Position adjustment".
3.3.3 Seal for flange mounting
➀ ➁
P01-FMD7xxxx-11-xx-xx-xx-002
Fig. 9: Mounting the versions with flange or diaphragm seal

1 Diaphragm
2 Seal
# Warning!
The seal is not allowed to press on the diaphragm as this could affect the measurement result.
12 Endress+Hauser
3.3.4 Heat insulation – PMC71 high temperature version and PMP75

The PMC71 (high temperature version) and the PMP75 must only be insulated up to a certain
height. The maximum permitted insulation height is labelled on the devices and applies to an
insulation material with a heat conductivity ≤ 0.04 W/(m x K) and to the maximum permitted
ambient and process temperature (→ see table below). The data were determined under the most
critical application "quiescent air".
λ ≤ 0.04 W
TA m•K
TP
Fig. 10: Maximum insulation height, here e.g. PMC71 with flange
PMC71 high temperature version PMP75
Ambient temperature (TA) ≤ 70°C (158°F) ≤ 70°C (158°F)
Process temperature (TP) ≤ 150°C (302°F) max. 350°C (662°F), depending on the
diaphragm seal filling oil used (→ see
Technical Information TI383P Cerabar S)
3.3.5 Wall and pipe-mounting (optional)

Endress+Hauser offers a mounting bracket for installing on pipes or walls.
101
118
70
Please note the following when mounting:

• The cable entry should always point downwards so that moisture on the connecting cable can
drain off and not penetrate the housing.
• In the case of pipe mounting, the nuts on the bracket must be tightened uniformly with a torque
of at least 5 Nm.
Endress+Hauser 13
3.3.6 PMP71, version prepared for diaphragm seal mount –

welding recommendation
➀ ➁ ➂
A1
5
ø2.5
ø7.95
Fig. 11: Version U1: prepared for diaphragm seal mount

1 Hole for filling fluid
2 Bearing
3 Threaded pin with an internal hexagon 4 mm
A1 see the following table "Welding recommendation"
Welding recommendation
For the "U1 Prepared for diaphragm seal mount" version in feature 70 "Process connection;
Material" in the order code of up to including 40 bar-sensors, Endress+Hauser recommends welding
on the diaphragm seal as follows: the total welding depth of the fillet weld is 1 mm at an external
diameter of 16 mm. Welding is performed according to the WIG method.
Consecutive Sketch/welding groove Base material Welding Welding Inert gas,

seam no. shape, dimension as per matching process position additives
DIN 8551 DIN EN
ISO 24063
A1 Adapter made of 141 PB Inert gas

s1 a0.8
for sensors 1.4435 (AISI 316L) Ar/H 95/5
≤ 40 bar to be welded to
diaphragm seal made of Additive:
1.4435 or 1.4404 1.4430
(AISI 316L) (ER 316L Si)
3.3.7 Rotating the housing

The housing can be rotated up to 380° by loosening the Allen screw.
FIELD TERMINALS
max. 380°
Fig. 12: Aligning the housing

– T14 and T15 housing: Loosen setscrew with a 2 mm Allen key.
T17 housing: Loosen setscrew with a 3 mm Allen key.
– Rotate housing (max. up to 380°).
– Retighten setscrew.
14 Endress+Hauser
Cerabar S PMC71, PMP71/72/75 with 4...20 mA HART Wiring
3.4 Post-installation check

After installing the device, carry out the following checks:
• Are all screws firmly tightened?
• Are the housing covers screwed down tight?
4 Wiring
4.1 Connecting the device

! Note!
• When using the measuring device in hazardous areas, installation must comply with the
corresponding national standards and regulations and the Safety Instructions (XAs) or Installation
or Control Drawings (ZDs).
• Devices with integrated overvoltage protection must be earthed.
• Protective circuits against reverse polarity, HF influences and overvoltage peaks are installed.
• The supply voltage must match the supply voltage on the nameplate. (→ See also page 6, section
2.1.1 Nameplate.)
• Switch off the supply voltage before connecting the device.
• Remove housing cover of the terminal compartment.
• Guide cable through the gland. Preferably use twisted, screened two-wire cable.
• Connect device in accordance with the following diagram.
• Screw down housing cover.
• Switch on supply voltage.
➀ ➅ 10.5 V DC
➆ 11.5 V DC
4…20 mA
Test
Test
➁ 4... 20mA Test
➂ ➄
➇
4... 20mA Test
➃
P01-xMx7xxxx-04-xx-xx-xx-001
Fig. 13: Electrical connection 4...20 mA HART

→ Observe also section 4.2.1 "Supply voltage", page 17.
1 Housing
2 Jumper for 4...20 mA test signal.
→ See also page 17, section 4.2.1, "Taking 4...20 mA test signal" part.
3 Internal earth terminal
4 External earth terminal
5 4...20 mA test signal between plus and test terminal
6 minimum supply voltage = 10.5 V DC, jumper is inserted in accordance with the illustration.
7 minimum supply voltage = 11.5 V DC, jumper is inserted in "Test" position.
8 Devices with integrated overvoltage protection are labelled OVP (overvoltage protection) here.
Endress+Hauser 15
Wiring Cerabar S PMC71, PMP71/72/75 with 4...20 mA HART
4.1.1 Connecting devices with Harting plug Han7D
Cerabar S
+
+ –
7
6 8
Han7D 1 –
5 2
4 3
+ –
Fig. 14: Left: electrical connection for devices with Harting plug Han7D
Right: view of the plug at the device
4.1.2 Connection devices with M12 plug
Cerabar S
+ –
BK – +
M12
+ –
Fig. 15: Left: electrical connection for devices with M12 plug
4.1.3 Connection devices with 7/8" plug
Cerabar S
–
+ –
7/8" +
+ –
Fig. 16: Left: electrical connection for devices with 7/8" plug
16 Endress+Hauser
4.2 Connecting the measuring unit
4.2.1 Supply voltage
! Note!
• All explosion protection data are given in separate documentation which is available upon
request. The Ex documentation is supplied as standard with all devices approved for use in
explosion hazardous areas.
• When using the measuring device in hazardous areas, installation must comply with the
corresponding national standards and regulations and the Safety Instructions (XAs) or Installation
or Control Drawings (ZDs).
Electronic version Jumper for 4...20 mA test signal in Jumper for 4...20 mA test signal in
"Test" position (Delivery status) "Non-Test" position
4...20 mA HART, for non-hazardous 11.5...45 V DC 10.5...45 V DC

areas
Taking 4...20 mA test signal

A 4...20 mA signal may be measured via the positive and test terminal without interrupting the
measurement. The minimum supply voltage of the device can be reduced by simply changing the
position of the jumper. As a result, operation is also possible with lower voltage sources. To keep
the measured error below 0.1%, the current measuring device should display an internal resistance
of < 0.7 Ω. Observe the position of the jumper in accordance with the following table.
Jumper position for test signal Description
– Taking 4...20 mA test signal via plus and test terminal:

Test possible. (Thus, the output current can be measured without
interruption via the diode.)
– Delivery status
– minimum supply voltage: 11.5 V DC
– Taking 4...20 mA test signal via plus and test terminal:

Test not possible.
– minimum supply voltage: 10.5 V DC
4.2.2 Cable specification

• Endress+Hauser recommends using twisted, screened two-wire cables.
• Terminals for wire cross-sections 0.5...2.5 mm2
• Cable external diameter: 5...9 mm
Endress+Hauser 17
4.2.3 Load
U – 10.5 V U – 11.5 V
➀ RLmax RLmax ≤
23 mA ➁ RLmax RLmax ≤
23 mA
[Ω] [Ω]
Test 1500 Test
1456
1282 1239
847 804
➃ ➃
413
➂ 369
➂
10.5 20 30 40 45 U 11.5 20 30 40 45 U
[V] [V]
U – 11 V U – 12 V
RLmax RLmax ≤ RLmax RLmax ≤
[Ω] 23 mA [Ω] 23 mA
1478 1434
1260 1217
826 782
391
➄ ➄
347
11 20 30 40 45 U 12 20 30 40 45 U
[V] [V]
Fig. 17: Load diagram, observe the position of the jumper and the explosion protection. (→ See also page 17, "Taking
4...20 mA test signal" part.)
1 Jumper for the 4...20 mA test signal inserted in "Non-Test" position
2 Jumper for the 4...20 mA test signal inserted in "Test" position
3 Supply voltage 10,5 (11,5)...30 V DC for EEx ia, 1 D, 1/2 GD, FM IS and CSA IS
4 Supply voltage10,5 (11,5)...45 V DC for devices for non-hazardous areas, 1/3 D, EEx d, EEx nA, FM XP, FM DIP,
FM NI, CSA XP and CSA Dust-Ex
5 Supply voltage 11 (12)...45 V DC for PMC71, EEx d[ia], FM XP, CSA XP
RLmax Maximum load resistance
U Supply voltage
! Note!
When operating via a handheld terminal or via PC with an operating program, a minimum
communication resistance of 250 Ω must exist within the loop.
4.2.4 Screening/potential matching

• You achieve optimum screening against disturbances if the screening is connected on both sides
(in the cabinet and on the device). If you have to reckon with potential equalisation currents in
the plant, only earth screening on one side, preferably at the transmitter.
• When using in hazardous areas, you must observe the applicable regulations.
Separate Ex documentation with additional technical data and instructions is included with all Ex
systems as standard.
• Ex applications: set up potential matching inside and outside the hazardous area. Connect all
devices to the local potential matching.
18 Endress+Hauser
4.2.5 Connecting HART handheld terminal

With a HART handheld terminal you can set and check the transmitter and avail of additional
functions all along the 4...20 mA line.
➀ min. 250 Ω
Test
4…20 mA
4... 20mA Test
➂ DELTABAR: * * * * * * * *
ONLINE
1 QUICK SETUP
2 OPERATING MENU
3 PV
dsdmdm
df das.
asdas fa
asas la.
352 mbar
➁ DELTABAR: * * * * * * * *
ONLINE
1 QUICK SETUP
2 OPERATING MENU
3 PV
dsdmdm
df das.
asdas fa
asas la.
352 mbar
DELTABAR: * * * * * * * *
ONLINE
1 QUICK SETUP
2 OPERATING MENU
3 PV
dsdmdm
df das.
asdas fa
asas la.
352 mbar
4 SV 0 °C 4 SV 0 °C 4 SV 0 °C
HELP SAVE HELP SAVE HELP SAVE
6 6 6
9 Page
Up 9 Page
Up 9 Page
Up
EX EX
Bksp Delete Bksp Delete Bksp Delete
Page Page Page

On On On
#%& ABC DEF #%& ABC DEF #%& ABC DEF

1 2 3 1 2 3 1 2 3
Copy Paste Hot Key Copy Paste Hot Key Copy Paste Hot Key
GHI JKL MNO GHI JKL MNO GHI JKL MNO

4 5 6 4 5 6 4 5 6
Insert + Hot Key Insert + Hot Key Insert + Hot Key
PQRS TUV W XY Z PQRS TUV W XY Z PQRS TUV W XY Z

7 8 9 7 8 9 7 8 9
,()‘ _<> +*/ ,()‘ _<> +*/ ,()‘ _<> +*/
. 0 - . 0 - . 0 -
375 375 375

FIELD COMMUNICATOR FIELD COMMUNICATOR FIELD COMMUNICATOR
Fig. 18: Connecting an HART handheld terminal, e.g. Field Communicator DXR375
1 Necessary communication resistor ≥ 250 Ω
2 HART handheld terminal
3 HART handheld terminal, directly connected to the device even in the Ex i-area
# Warning!
• In the case of Ex d type of protection, do not connect the handheld terminal in the hazardous area.
• Do not replace the battery of the handheld terminal in the hazardous area.
• For devices with FM or CSA certificates, establish electrical connection as per Installation or
Control Drawing (ZD...) supplied.
Endress+Hauser 19
4.2.6 Connecting Commubox FXA191 for operation via

TOF Tool, FieldCare or Commuwin II
The Commubox FXA 191 connects Smart Transmitters with HART protocol to the serial interface
(RS 232) of a computer. This makes it possible to remotely operate the transmitters with the aid of
the Endress+Hauser operating programs ToF Tool or Commuwin II. The Commubox is also suitable
for use in intrinsically safe circuits.
min. 250 Ω
➂
Test
4…20 mA
4... 20mA Test
EX EX
Fig. 19: Connecting PC with operating programs ToF Tool, FieldCare or Commuwin II via Commubox FXA 191
1 Computer with operating program ToF Tool, FieldCare or Commuwin II
2 Commubox FXA191
3 Necessary communication resistor ≥ 250 Ω
4.3 Potential matching

Potential matching does not have to be set up.
4.4 Overvoltage protection (optional)

Devices showing version "M" in feature 100 "Additional options 1" or feature 110 "Additional
options 2" in the order code are equipped with overvoltage protection (see also Technical
Information TI382P "Ordering information".
• Overvoltage protection:
– Nominal functioning DC voltage: 600 V
– Nominal discharge current: 10 kA
• Surge current check î = 20 kA as per DIN EN 60079-14: 8/20 µs satisfied
• Arrester AC current check I = 10 A satisfied
# Warning!
Devices with integrated overvoltage protection must be earthed.
4.5 Post-connection check

Perform the following checks after completing electrical installation of the device:
• Does the supply voltage match the specifications on the nameplate?
• Is the device connected as per section 4.1?
• Are all screws firmly tightened?
• Are the housing covers screwed down tight?
As soon as voltage is applied to the device, the green LED on the electronic insert lights up for a few
seconds or the connected on-site display lights up.
20 Endress+Hauser
Cerabar S PMC71, PMP71/72/75 with 4...20 mA HART Operation
5 Operation
Feature 20 "Output; operation" in the order code provides you with information on the operating
options available to you.
Versions in the order code Operation
A 4...20 mA HART; external operation, LCD Via on-site display and 1 key on the exterior of the device
B 4...20 mA HART; internal operation, LCD Via on-site display and 1 key on the inside of the device
C 4...20 mA; internal operation Without on-site display, 1 key on the inside of the device
5.1 On-site display (optional)

A 4-line liquid crystal display (LCD) is used for display and operation. The on-site display shows
measured values, dialog texts, fault messages and notice messages.
Functions:
• 8-digit measured value display including sign and decimal point, bargraph for current display
• simple and complete menu guidance thanks to separation of the parameters into several levels and
groups
• each parameter is given a 3-digit ID number for easy navigation
• option for configuring the display according to individual requirements and desires, such as
language, alternating display, contrast setting, display of other measured values such as sensor
temperature
• comprehensive diagnostic functions (fault and warning message, peak-hold indicators, etc.)
• rapid and safe commissioning with the Quick Setup menus
Measured value display Parameter

Identification
Function name Value number
Header line
Main line
Unit
Information
line
– + E Symbol
Bargraph
Editing modes
Operating keys
Selection
options
Value that
can be edited
Current measured value

Endress+Hauser 21
Operation Cerabar S PMC71, PMP71/72/75 with 4...20 mA HART
The following table illustrates the symbols that can appear on the on-site display. Four symbols can
occur at one time.
Symbol Meaning
Alarm symbol
– Symbol flashing: warning, device continues measuring.
– Symbol permanently lit: error, device does not continue measuring.
Note: The alarm symbol may overlie the tendency symbol.
Lock symbol
The operation of the device is locked. Unlock device, → see section 5.10.
Communication symbol
Data transfer via communication
Note: The alarm symbol may overlie the communication symbol.
Square root symbol

Active measuring mode "Flow measurement"
The root flow signal is used for the current output.
Tendency symbol (increasing)

The measured value is increasing.
Tendency symbol (decreasing)

The measured value is decreasing.
Tendency symbol (constant)

The measured value has remained constant over the past few minutes.
5.2 Operating elements
5.2.1 Position of operating elements

The operating keys are located either under the protective cap on the exterior of the device or inside
on the electronic insert. Operating keys are also located on the optional on-site display.
➃➄
τ ➅
on
➀
➀
off
➁
Damping [τ]
Display
on Sensor
➂
1 2
off
PC
HistoROM
P01-PMx7xxxx-19-xx-xx-xx-009 P01-xxxxxxxx-19-xx-xx-xx-074
Fig. 20: Operating keys, external Fig. 21: Operating keys, internal
1 Operating keys on the exterior of the device under 1 Operating keys
the protective flap 2 Slot for optional display
3 Slot for optional HistoROM®/M-DAT
4 DIP-switch for locking/unlocking measured-value-
relevant parameters
6 DIP-switch for damping on/off
7 Green LED to indicate value being accepted
22 Endress+Hauser
5.2.2 Function of the operating elements –

on-site display not connected
Operating key(s) Meaning
! Note!
• The device is configured for the pressure measuring mode as standard. You can switch
measuring modes by means of the MEASURING MODE parameter. → See page 39,
section 6.2 "Selecting language and measuring mode".
• Press the key for at least 3 seconds to accept the pressure value applied.
MEASURING MODE "Pressure":

• The pressure applied is assigned to the lower current value (SET LRV – pressure1).
! Note!
• MEASURING MODE "Level":
The factory settings for the LEVEL MODE, CALIBRATION MODE, LIN. MEASURAND,
EMPTY CALIB. and FULL CALIB. parameters are as follows:
– LEVEL MODE = Linear
– CALIBRATION MODE = wet
– LIN. MEASURAND = %
– EMPTY CALIB. = 0 %
S – FULL CALIB. = 100 %.
These parameters can only be modified by means of the on-site display or remote
operation such as the ToF Tool.
MEASURING MODE "Level", CALIBRATION MODE "wet":
• FÜLLSTANDSSTYP "Linear":
– The pressure applied is saved as the lower pressure value (EMPTY PRESSURE1) and
assigned to the lower level value (EMPTY CALIB.1). The lower level and current
values (SET LRV - level1) remain unchanged. These values can only be modified by
means of the on-site display or remote operation such as the ToF Tool.
→ See also page 44, section 6.5.2 "Quick Setup menu for Level measuring mode" and
Operating Instructions BA274P, parameter descriptions LEVEL MODE,
CALIBRATION MODE, EMPTY CALIB., EMPTY PRESSURE and SET LRV – Level.
• LEVEL MODE "Pressure Linearized" or "Height Linearized":
– The key does not have any function.
MEASURING MODE "Level", CALIBRATION MODE "dry":
• The key does not have any function.
Endress+Hauser 23
! Note!
• The device is configured for the pressure measuring mode as standard. You can switch
measuring modes by means of the MEASURING MODE parameter. → See page 39,
section 6.2 "Selecting language and measuring mode".
• Press the key for at least 3 seconds to accept the pressure value applied.
MEASURING MODE "Pressure":
• The pressure applied is assigned to the upper current value (SET URV – pressure1).
! Note!
• MEASURING MODE "Level":
The factory settings for the LEVEL MODE, CALIBRATION MODE, LIN. MEASURAND,
EMPTY CALIB. and FULL CALIB. parameters are as follows:
O – FULL CALIB. = 100 %.
These parameters can only be modified by means of the on-site display or remote
operation such as the ToF Tool.
MEASURING MODE "Level", CALIBRATION MODE "wet":
• LEVEL MODE "Linear":
– The pressure applied is saved as the upper pressure value (FULL PRESSURE1) and
assigned to the upper level value (FULL CALIB.1). The upper level and current values
(SET URV - level1) remain unchanged. These values can only be modified by means of
the on-site display or remote operation such as the ToF Tool.
→ See also page 44, section 6.5.2 "Quick Setup menu for Level measuring mode" and
Operating Instructions BA274P, parameter descriptions LEVEL MODE,
CALIBRATION MODE, FULL CALIB., FULL PRESSURE, and SET URV – Level.
• LEVEL MODE "Pressure Linearized" or "Height Linearized":
– The key does not have any function.
MEASURING MODE "Level", CALIBRATION MODE "dry":
• The key does not have any function.
F Position adjustment (Press key for at least 3s.)
Reset all parameters. The reset via operating keys corresponds to the software reset code
O and S and F 7864. (Press key for at least 6s.)
O and F Copy the configuration data from the optional HistoROM®/M-DAT module to the device.
S and F Copy the configuration data from the device to the optional HistoROM®/M-DAT module.
– DIP-switch 1: for locking/unlocking measured-value-relevant parameters

τ on Factory setting: off (unlocked)
– DIP-switch 2: damping on/off,
Factory setting: on (damping on)
1 2 off
P01-xxxxxxxx-19-xx-xx-xx-057
1) Parameter name used for the on-site display or remote operation such as the ToF Tool.
24 Endress+Hauser
5.2.3 Function of the operating elements –

on-site display connected
O – Navigate upwards in the picklist

– Edit the numerical values and characters within a function
S – Navigate downwards in the picklist

– Edit the numerical values and characters within a function
F – Confirm entry
– Jump to the next item
Contrast setting of on-site display: darker

O and F
Contrast setting of on-site display: brighter
S and F
ESC functions:
– Exit edit mode without saving the changed value.
– You are in a menu within a function group. The first time you press the keys
simultaneously, you go back a parameter within the function group. Each time you press
O and S the keys simultaneously after that, you go up a level in the menu.
– You are in a menu at a selection level. Each time you press the keys simultaneously, you
go up a level in the menu.
Note: The terms function group, level and selection level are explained in section 5.4.1,
page 28.
– DIP-switch 1: for locking/unlocking measured-value-relevant parameters

τ on Factory setting: off (unlocked)
– DIP-switch 2: damping on/off,
Factory setting: on (damping on)
1 2 off
Endress+Hauser 25

on-site display not connected
! Note!
To operate the device with a HistoROM®/M-DAT module see page 30, Section 5.5 "HistoROM®/
M-DAT module".
5.3.1 Pressure measuring mode

If no on-site display is connected, the following functions are possible by means of the three keys
on the electronic insert or on the exterior of the device:
• Position adjustment (zero point correction)
• Setting lower range value and upper range value
• Device reset, → see also page 23, section 5.2.2 "Function of the operating elements", Table.
! Note!
• The operation must be unlocked. → See page 36, section 5.10 "Locking /unlocking operation".
• The device is configured for the Pressure measuring mode as standard. You can switch measuring
modes by means of the MEASURING MODE parameter. → See page 39, section 6.2 "Selecting
language and measuring mode".
• The pressure applied must be within the nominal pressure limits of the sensor. See information
on the nameplate.
Carry out position adjustment. Setting lower range value. Setting upper range value.
Pressure is present at device. Desired pressure for lower range Desired pressure for upper range
value is present at device. value is present at device.
↓ ↓ ↓
Press "E"-key for 3 s. Press "–"-key for 3 s. Press "+"-key for 3 s.
↓ ↓ ↓
Does the LED on the electronic insert Does the LED on the electronic insert Does the LED on the electronic insert
light up briefly? light up briefly? light up briefly?
Yes No Yes No Yes No
↓ ↓ ↓ ↓ ↓ ↓
Applied pressure Applied pressure Applied pressure Applied pressure Applied pressure Applied pressure
for for position for for for for
position adjustment has lower range value lower range value upper range value upper range value
adjustment has not been has been has not been has been has not been
been accepted. accepted. accepted. accepted. accepted. accepted.
Observe the input Observe the input Observe the input
limits. limits. limits.
26 Endress+Hauser
5.3.2 Level measuring mode
! Note!
If no on-site display is connected, the following functions are possible by means of the three keys
on the electronic insert or on the exterior of the device:
• Position adjustment (zero point correction)
• Set the lower and upper pressure value and assign to the lower and upper level value
• Device reset, → see also page 23, section 5.2.2 "Function of the operating elements", Table.
• The operation must be unlocked. → See page 36, section 5.10 "Locking /unlocking operation".
• The device is configured for the Pressure measuring mode as standard. You can switch measuring
modes by means of the MEASURING MODE parameter. → See page 39, section 6.2 "Selecting
language and measuring mode".
• The S and O keys do not have any function if the LEVEL MODE "Pressure linearized" or "Height
linearized" or the CALIBRATION MODE "dry" was selected.
• The factory settings for the LEVEL MODE, CALIBRATION MODE, LIN. MEASURAND, EMPTY
CALIB. and FULL CALIB. parameters are as follows:
– FULL CALIB. = 100 %.
These parameters can only be modified by means of the on-site display or remote operation such
as the ToF Tool.
• The pressure applied must be within the nominal pressure limits of the sensor. See information
on the nameplate.
• → See also page 44, section 6.5.2 "Quick Setup menu for Level measuring mode" and Operating
Instructions BA274P, parameter descriptions LEVEL MODE, CALIBRATION MODE, EMPTY
CALIB., FULL CALIB., EMPTY PRESSURE, FULL PRESSURE, SET LRV – Level and SET URV –
Level.
Carry out position adjustment. Setting lower pressure value. Setting upper pressure value.
Pressure is present at device. Desired pressure for lower pressure Desired pressure for upper pressure
value (EMPTY PRESSURE1) is present value (FULL PRESSURE1) is present
at device. at device.
↓ ↓ ↓
Press "E"-key for 3 s. Press "–"-key for 3 s. Press "+"-key for 3 s.
↓ ↓ ↓
Does the LED on the electronic insert Does the LED on the electronic insert Does the LED on the electronic insert
light up briefly? light up briefly? light up briefly?
Yes No Yes No Yes No
↓ ↓ ↓ ↓ ↓ ↓
Applied pressure Applied pressure The pressure The pressure The pressure The pressure
for for position present was saved present was not present was saved present was not
position adjustment has as the lower saved as the as the upper saved as the
adjustment has not been pressure value lower pressure pressure value upper pressure
been accepted. accepted. (EMPTY value. Observe (FULL value. Observe
Observe the input PRESSURE1) and the input limits. PRESSURE1) and the input limits.
limits. assigned to the assigned to the
lower level value upper level value
(EMPTY (FULL CALIB.1).
CALIB.1).
1) Parameter name used for the on-site display or remote operation such as the ToF Tool.
Endress+Hauser 27

on-site display connected
If the on-site display is connected, the three operating keys are used to navigate through the
operating menu, → see page 25, section 5.2.3 "Function of the operating elements".
5.4.1 General structure of the operating menu

The menu is split into four levels. The three upper levels are used to navigate while you use the
bottom level to enter numerical values, select options and save settings. The entire menu is
illustrated in section 10.1 "Menu for on-site display, ToF Tool, FieldCare and HART handheld
terminal".
The structure of the OPERATING MENU depends on the measuring mode selected, e.g. if the
"Pressure" measuring mode is selected, only the functions necessary for this mode are displayed.
Measured value
GROUP SELECTION
LANGUAGE MEASURING MODE QUICK SETUP OPERATING MENU
➁
➀ SETTINGS DISPLAY
POSITION ADJUSTMENT BASIC SETUP EXTENDED SETUP
POS. ZERO ADJUST
➂
➃ POS. INPUT VALUE
CALIB. OFFSET
Fig. 22: Structure of the operating menu

1 1. Selection level
2 2. Selection level
3 Function groups
4 Parameter
! Note!
The LANGUAGE and MEASURING MODE parameters are only displayed via the on-site display on
the 1st selection level. In the ToF Tool or HART handheld terminal, the LANGUAGE parameter is
displayed in the DISPLAY group and the MEASURING MODE parameter is displayed in the QUICK
SETUP menus or in the BASIC SETUP function group. → See also section 10.1 "Operating menu
for on-site display, ToF Tool, FieldCare and HART handheld terminal".
28 Endress+Hauser
5.4.2 Selecting an option

Example: select "English" as the language of the menu.
On-site display Operation
German is selected as the language. A ✓in front of the

menu text indicates the active option.
Select English with "+" or "–".
1. Confirm your choice with "E". A ✓ in front of the

menu text indicates the active option. (English is now
selected as the menu language.)
2. Jump to the next item with "E".
5.4.3 Editing a value

Example: adjusting DAMPING VALUE function from 2.0 s to 30.0 s. → See also page 25, section
5.2.3 "Function of the operating elements".
The on-site display shows the parameter to be changed.

The value highlighted in black can be changed. The "s" unit
is fixed and cannot be changed.
1. Press "+" or "–" to get to the editing mode.

2. The first digit is highlighted in black.
1. Use "+" to change "2" to "3".

2. Confirm "3" with "E". The cursor jumps to the next
position (highlighted in black).
The decimal point is highlighted in black, i.e. you can now

edit it.
1. Keep pressing "+" or "–" until "0" is displayed.

2. Confirm "0" with "E".
The cursor jumps to the next position. ↵ is displayed
and is highlighted in black. → See next graphic.
Endress+Hauser 29
Use "E" to save the new value and exit the editing mode.
→See next graphic.
The new value for the damping is now 30.0 s.

– Jump to the next parameter with "E".
– You can get back to the editing mode with "+" or
"–".
5.4.4 Taking pressure applied at device as value

Example: configuring upper range value – assign 20 mA to the pressure value 400 mbar.
The bottom line on the on-site display displays the pressure

present, here 400 mbar.
Use "+" or "–" to switch to the "Confirm" option. The active

selection is highlighted in black.
Use "E" to assign the value (400 mbar) to the GET URV
parameter. The device confirms the calibration and jumps
back to the parameter, here GET URV (see next graphic).
Switch to the next parameter with "E".
5.5 HistoROM®/M-DAT (optional)

HistoROM®/M-DAT is a memory module, which is attached to the electronic insert and fulfils the
following functions:
• Back-up copy of configuration data
• Copying configuration data of a transmitter into another transmitter
• Cyclic recording of pressure and sensor-temperature measured values
• Recording diverse events, such as alarms, configuration changes, counters for measuring range
undershooting and exceeding for pressure and temperature, exceeding and undershooting the
user limits for pressure and temperature, etc.
# Warning!
Detach HistoROM®/M-DAT from the electronic insert or attach it to the insert in a deenergised
state only.
30 Endress+Hauser
! Note!
• The HistoROM®/M-DAT module may be retrofitted at any time (Order No.: 52027785).
• The HistoROM data and the data in the device are analysed once a HistoROM®/M-DAT is
attached to the electronic insert and power is reestablished to the device. During the analysis, the
messages "W702, HistoROM data not consistent" and "W706, Configuration in HistoROM and
device not identical" can occur. For measures, see page 46, section 8.1 "Messages."
5.5.1 Copying configuration data
! Note!
When copying configuration data from one device into another, the following parameters are also
overwritten:
• DEVICE SERIAL No
• DEVICE DESIGN
• CUST. TAG NUMBER
• BUS ADDRESS
• all parameters in the PROCESS CONNECTION group.
These have to be reentered depending on the application. To reenter the DEVICE SERIAL No and
DEVICE DESIGN parameters, please contact Endress+Hauser Service. (→ See also
www.endress.com/worldwide.)
➁
on
τ
off 1 2
Damping [τ]
Display
on Sensor
1 2
off
PC
HistoROM ➀
Abb. 23: Electronic insert with optional HistoROM®/M-DAT memory module

1 optional HistoROM®/M-DAT
2 To copy configuration data from the HistoROM®/M-DAT module to a device, the operation must be unlocked DIP-
switch 1, Position "off" ,parameter INSERT PIN NO. = 100). To copy configuration data from a device to a
HistoROM®/M-DAT module, the operation may be locked or unlocked. Observe page 36, section 5.10 "Locking/
unlocking operation".
On-site operation – on-site display not connected

Copying configuration data from a device to a HistoROM®/M-DAT module:
1. Disconnect device from supply voltage.
2. Attach the HistoROM®/M-DAT module to the electronic insert.
3. Reestablish supply voltage to the device.
4. Press F and S-keys (for at least 3 seconds) until the LED on the electronic insert lights up.
5. Wait approx. 20 seconds. Configuration data are loaded from the device to the HistoROM®/
M-DAT. The device is not restarted.
6. Disconnect device from the supply voltage again.
7. Detach memory module.
Endress+Hauser 31
Copying configuration data from a HistoROM®/M-DAT to a device:
! Note!
The operation must be unlocked. → See also page 36, section 5.9 "Locking/unlocking operation".
2. Attach the HistoROM®/M-DAT module to the electronic insert. Configuration data from
another device are stored in the HistoROM®/M-DAT.
4. Press F and S-keys (for at least 3 seconds) until the LED on the electronic insert lights up.
M-DAT. The device is restarted.
6. Before removing the HistoROM®/M-DAT again from the electronic insert, disconnect the
device from supply voltage.
On-site operation via on-site display (optional) or remote operation

Copying configuration data from a device to a HistoROM®/M-DAT:
2. Attach the HistoROM®/M-DAT module to the electronic insert.
4. Using the HistoROM CONTROL parameter select the option "Device → HistoROM" as the
data transfer direction.
(Menu path: GROUPSELECTION → OPERATING MENU → OPERATION)
M-DAT. The device is not restarted.
6. Disconnect device from the supply voltage again.
7. Detach memory module.
Copying configuration data from a HistoROM®/M-DAT to a device:
! Note!
The operation must be unlocked. → See also page 36, section 5.9 "Locking/unlocking operation".
2. Attach the HistoROM®/M-DAT module to the electronic insert. Configuration data from
another device are stored in the HistoROM®/M-DAT.
4. Using the HistoROM CONTROL parameter select the option "Device → HistoROM" as the
data transfer direction.
(Menu path: GROUP SELECTION → OPERATING MENU → OPERATION)
M-DAT. The device is restarted.
6. Before removing the HistoROM®/M-DAT again from the electronic insert, disconnect the
device from supply voltage.
32 Endress+Hauser
5.6 Operation via HART handheld terminal

Use the HART handheld terminal to set all parameters all the way along the 4...20 mA cable via
menu operation.
dsdmdm
df das.
asdas fa
asas la.
dsdmdm
df das.
asdas fa
asas la.
DELTABAR: * * * * * * * *
DELTABAR: * * * * * * * * ONLINE
ONLINE
1 QUICK SETUP 1 QUICK SETUP
Delete
➀
2 OPERATING MENU 2 OPERATING MENU
3 PV 352 mbar
4 SV 0 °C 3 PV 352 mbar
4 SV 0 °C
HELP SAVE
H dsdmdm
df das.
asdas fa
asas la.
DELTABAR: * * * * * * * *
6
9
HELP SAVE
Page OPERATING MENU
Up
➁
1 SETTINGS
Bksp Delete 2 DISPLAY Delete
3 OUTPUT
Page 4 TRANSMITTER INFO
On Bksp 5 PROCESS INFO
➂
#%& ABC DEF
1 2 3
Copy
GHI
Paste
JKL
Hot Key
MNO
H dsdmdm
df das.
asdas fa
asas la.
4 5 6 SAVE HOME DELTABAR: * * * * * * * *

Insert + Hot Key
SETTINGS
PQRS TUV W XY Z
1 POSITION ADJUSTMENT
Page
7 8 9
2 BASIC SETUP Up
,()‘ _<> +*/ 3 EXTENDED SETUP
. 0 - 4 LINEARISATION
Bksp 5 TOTALIZER SETUP Page
On
375
FIELD COMMUNICATOR
SAVE HOME
Fig. 24: HART handheld terminal, here e.g. Field Communicator DXR375 and menu guidance
1 LC display with menu text
2 Keys for menu selection
3 Keys for parameter entry
! Note!
• → See also page 19, section 4.2.5 "Connecting HART handheld terminal".
• For further information, please refer to the Operating Instructions for the handheld terminal. The
Operating Instructions are supplied with the handheld terminal.
Endress+Hauser 33
5.7 ToF Tool operating program

The ToF Tool is a graphic and menu-guided operating program for measuring devices from
Endress+Hauser. It is used for supporting the commissioning, data storage, signal analysis and
documentation of the devices. The following operating systems are supported: WinNT4.0,
Win2000 and Windows XP. You can set all parameters via the ToF Tool.
The ToF Tool supports the following functions:
• Configuration of transmitters in online operation
• Loading and saving device data (upload/download)
• HistoROM®/M-DAT analysis
• Documentation of the measuring point
• Calculation of tank characteristics for the level measuring mode
P01-PMx7xxxxx-19-xx-xx-en-000
Fig. 25: ToF Tool operating program, the configuration is performed via a menu
Connection options:
• HART via Commubox FXA191 and the serial interface RS 232 C of a computer
• Service interface with adapter FXA193
! Note!
• → See also page 20, section 4.2.6 "Connecting Commubox FXA191 for operation via TOF Tool,
FieldCare or Commuwin II".
• Further information on the ToF Tool can be found on the CD-ROM supplied with the device or
on the Internet (http://www.endress.com, Download → Search for: ToF Tool) The CD is
supplied with any device ordered with the "HistoROM/M-DAT" option.
34 Endress+Hauser
5.8 FieldCare
FieldCare is an Endress+Hauser asset management tool based on FDT technology. With FieldCare,
you can configure all Endress+Hauser devices as well as devices from other manufacturers that
support the FDT standard. The following operating systems are supported: WinNT4.0, Win2000
and Windows XP.
FieldCare supports the following functions:
• Configuration of transmitters in online operation
• HistoROM®/M-DAT analysis
• Documentation of the measuring point
Connection options:
• HART via Commubox FXA191 and the serial interface RS 232 C of a computer
• HART via Fieldgate FXA520
! Note!
• → See also page 20, section 4.2.6 "Connecting Commubox FXA191 for operation via TOF Tool,
FieldCare or Commuwin II".
• Further information on the FieldCare can be found on the Internet (http://www.endress.com,
Download → Search for: FieldCare).
5.9 Commuwin II operating program

Commuwin II is a graphically supported operating program for intelligent measuring devices with
the HART and PROFIBUS PA communication protocols. The following operating systems are
supported: Win3.1/3.11, Win95, Win98, WinNT4.0 and Win2000. Commuwin II shows the most
important parameters (→ see also section 10.2 "Operating matrix HART Commuwin II).
Commuwin II supports the following functions:
• Configuration of measuring devices in on-line operation via matrix operation
• Visualisation of measured and limit values
• Presentation and recording of measured values with a line recorder.
! Note!
• For further information, please refer to the Operating Instructions BA124F "Commuwin II
FXS113".
• You can obtain the current device description (DD) either from your local Endress+Hauser Sales
Office or via the Internet (http://www.endress.com).
Endress+Hauser 35
5.10 Locking/unlocking operation

Once you have entered all the parameters, you can lock your entries against unauthorised and
undesired access.
You have the following possibilities for locking/unlocking the operation:
• Via a DIP-switch on the electronic insert, locally on the display.
• Via the on-site display (optional)
• Via communication e.g. ToF Tool, Commuwin II and HART handheld terminal.
The -symbol on the on-site display indicates that operation is locked. Parameters which refer to
how the display appears, e.g. LANGUAGE and DISPLAY CONTRAST can still be altered.
! Note!
• If operation is locked by means of the DIP-switch, you can only unlock operation again by means
of the DIP-switch. If operation is locked by means of the on-site display or remote operation e.g.
ToF Tool, you can only unlock operation again by means of the on-site display or remote
operation.
• If the operation is locked, any change to the "Damping on/off" DIP switch will not have any
impact on the damping time. Any change will not take effect until the operation has been
unlocked again.
The table provides an overview of the locking functions:
Locking via View/read Modify/write via1 Unlocking via

parameter
On-site Remote DIP-switch On-site Remote
display operation display operation
DIP-switch Yes No No Yes No No
On-site display Yes No No No Yes Yes
Remote operation Yes No No No Yes Yes
1) Parameters which refer to how the display appears, e.g. LANGUAGE and DISPLAY CONTRAST can still be altered.
5.10.1 Locking/unlocking operation locally via DIP-switch

Damping [τ]
Damping [τ]
➀
➁ ➂
Damping [τ]
on on Display
on Sensor
1 2
off
PC
1 2 1 2
off off
HistoROM
– + E
Fig. 26: DIP-switch position "Hardware locking" on the electronic insert

1 If necessary, remove on-site display (optional)
2 DIP-switch is at "on": operation is locked.
3 DIP-switch is at "off": operation is unlocked (operation possible)
36 Endress+Hauser
5.10.2 Locking/unlocking operation via on-site display or remote

operation
Description
Locking operation 1. Select INSERT PIN NO. parameter,

Menu path: OPERATING MENU → OPERATION → INSERT PIN NO.
2. To lock operation, enter a number for this parameter between 0...9999 that is ≠100.
Unlocking operation 1. Select INSERT PIN NO. parameter.

2. To unlock operation, enter "100" for the parameter.
5.11 Factory setting (reset)

By entering a certain code, you can completely, or partially, reset the entries for the parameters to
the factory settings. (→ For factory settings refer to the Operating Instructions BA 274P "Cerabar S/
Deltabar S, Description of device functions". See also page 2, "Overview documentation".) Enter the
code by means of the ENTER RESET CODE parameter (Menu path: (GROUP SELECTION →)
OPERATING MENU → OPERATING).
There are various reset codes for the device. The following table illustrates which parameters are
reset by the particular reset codes. Operation must be unlocked to reset parameters (→ see page 36,
section 5.10).
! Note!
Any customer-specific configuration carried out by the factory is not affected by a reset (customer-
specific configuration remains). If, after a reset, you wish the parameters to be reset to the factory
settings, please contact Endress+Hauser Service.
Reset code Description and effect

1846 Display reset
– This reset resets all parameters which have to do with how the display appears (DISPLAY
group).
– Any simulation which may be running is ended.
– The device is restarted.
62 PowerUp reset (warm start)

– This reset resets all the parameters in the RAM. Data are read back anew from the
EEPROM (processor is initialised again).
2710 Measuring mode level reset

– Depending on the settings for the LEVEL MODE, LIN MEASURAND,
LINdMEASURAND or COMB. MEASURAND parameters, the parameters needed for
this measuring task will be reset.
Example LEVEL MODE = linear and LIN. MEASURAND = Height
• HEIGHT UNIT = m
• CALIBRATION MODE = wet
• EMPTY CALIB. = 0
• FULL CALIB. = Sensor end value converted to mH2O, e.g. 40.79 mH2O for a 400 mbar
sensor
333 User reset

– Affects the following parameters:
– Function group POSITION ADJUSTMENT
– Function group BASIC SETUP, except for the customer-specific units
– Function group EXTENDED SETUP
– Group OUTPUT
– Function group HART DATA: BUS ADDRESS and PREAMBLE NUMBER
Endress+Hauser 37
Reset code Description and effect
7864 Total reset

– Affects the following parameters:
– Function group POSITION ADJUSTMENT
– Function group BASIC SETUP
– Function group EXTENDED SETUP
– Function group LINEARISATION (an existing linearisation table is erased)
– Group OUTPUT
– Function group PEAK HOLD INDICATOR
– Function group HART DATA
– All configurable messages ("Error" type) are set to "Warning".
→ See also page 46, section 8.1 "Messages" and page 53, 8.2 "Response of outputs to
errors".
– Function group USER LIMITS
8888 HistoROM reset

The measured value memory and event memory are cleared. During the reset, the
HistoROM must be attached to the electronic insert.
38 Endress+Hauser
Cerabar S PMC71, PMP71/72/75 with 4...20 mA HART Commissioning
6 Commissioning
! Note!
The device is configured for the Pressure measuring mode as standard. The measuring range and
the unit in which the measured value is transmitted correspond to the specifications on the
nameplate.
6.1 Function check

Carry out a post-installation and a post-connection check as per the checklist before commissioning
the device.
• "Post-installation check" checklist → see section 3.4
• "Post-connection check" checklist → see section 4.4
6.2 Selecting language and measuring mode
6.2.1 On-site operation

The LANGUAGE and MEASURING MODE parameters are located on the top menu level. → See
also page, section 5.4.1 "General structure of the operating menu".
The following languages are available:
• Deutsch
• English
• Français
• Italiano
• Español
• Nederlands
• Chinese (on request)
• Japanese (on request)
The following measuring modes are available:
• Pressure
• Level
6.2.2 ToF Tool, FieldCare or HART handheld terminal

The MEASURING MODE parameter is displayed in the ToF Tool and in the HART handheld
terminal in the QUICK SETUP menus and in the BASIC SETUP function group (OPERATING
MENU → SETTINGS → BASIC SETUP).
The following measuring modes are available:
• Pressure
• Level
The LANGUAGE parameter is arranged in the ToF Tool and in the HART handheld terminal in the
DISPLAY group (OPERATING MENU → DISPLAY).
Use the LANGUAGE parameter to select the menu language for the on-site display. Select the menu
language for the ToF Tool via the "Options" menu → "Settings" → "Language" tab → "ToF Tool
language" field.
Select the menu language for FieldCare by means of the "Language Button" in the configuration
window.
Endress+Hauser 39
Commissioning Cerabar S PMC71, PMP71/72/75 with 4...20 mA HART
The following languages are available:

• Deutsch
• English
• Français
• Italiano
• Español
• Nederlands
• Chinese (on request)
• Japanese (on request)
6.3 Position adjustment

Due to the orientation of the device, there may be a shift in the measured value, i.e. when the
container is empty, the measured value parameter does not display zero. There are three options to
choose from when performing position adjustment.
(Menu path: (GROUP SELECTION →) OPERATING MENU → SETTINGS → POSITION
ADJUSTMENT)
Parameter name Description
POS. ZERO ADJUST (685) Position adjustment – the pressure difference between zero (set point) and the measured
Entry pressure need not be known. (A reference pressure is present at the device.)
Example:
– MEASURED VALUE = 2.2 mbar
– Correct the MEASURED VALUE via the POS. ZERO ADJUST parameter with the
"Confirm" option. This means that you are assigning the value 0.0 to the pressure
present.
– MEASURED VALUE (after pos. zero adjust) = 0.0 mbar
– The current value is also corrected.
The CALIB. OFFSET parameter displays the resulting pressure difference (offset) by which
the MEASURED VALUE was corrected.
Factory setting:
0
POS. INPUT VALUE (563) Position adjustment – the pressure difference between zero (set point) and the measured
Entry pressure need not be known. (A reference pressure is present at the device.)
Example:
– For the POS. INPUT VALUE parameter, specify the desired set point for the
MEASURED VALUE, e.g. 2 mbar.
(MEASURED VALUEnew = POS. INPUT VALUE)
– MEASURED VALUE (after entry for POS. INPUT VALUE) = 2.0 mbar
– The CALIB. OFFSET parameter displays the resulting pressure difference (offset) by
which the MEASURED VALUE was corrected.
CALIB. OFFSET = MEASURED VALUEold – POS. INPUT VALUE,
here: CALIB. OFFSET = 0.5 mbar – 2.0 mbar = – 1.5 mbar)
Factory setting:
0
CALIB. OFFSET (319) Position adjustment – the pressure difference between zero (set point) and the measured
Entry pressure is known. (A reference pressure is not present at the device.)
Example:
– Via the CALIB. OFFSET parameter, enter the value by which the MEASURED VALUE
should be corrected. To correct the MEASURED VALUE to 0.0 mbar, you must enter
the value 2.2 here.
(MEASURED VALUE new = MEASURED VALUEold – CALIB. OFFSET)
– MEASURED VALUE (after entry for calib. offset) = 0.0 mbar
Factory setting:
0
40 Endress+Hauser
6.4 Pressure measurement
6.4.1 Information on pressure measurement
! Note!
• There is a Quick Setup menu for each of the measuring modes Pressure and Level which guides
you through the most important basic functions. With the setting in the MEASURING MODE
parameter, you specify which Quick Setup menu should be displayed. → See also page 39, section
6.2 "Selecting language and measuring mode".
• For a detailed description of the parameters see the Operating Instructions BA 274P "Cerabar S/
Deltabar S, Description of device functions"
– Table 6, POSITION ADJUSTMENT
– Table 7, BASIC SETUP
– Table 13, EXTENDED SETUP
→ See also page 2, section "Overview documentation".
• For pressure measurement, select the "Pressure" option by means of the MEASURING MODE
parameter. The operating menu is structured appropriately. → See also section 10.1.
6.4.2 Quick Setup menu for Pressure measuring mode
Measured value
1)
GROUP SELECTION
1) 1)
2)
MEASURING MODE
Pressure Level
Gauge pressure sensors Absolut pressure sensors

POS. ZERO ADJUST POS. INPUT VALUE
SET LRV
SET URV
1) Display via on-site display only
2) Display via ToF Tool, FieldCare
and HART handheld terminal only DAMPING VALUE
Fig. 27: Quick Setup menu for Pressure measuring mode
On-site operation ToF Tool, FieldCare and HART handheld terminal
Measured value display Measured value display

On-site display: Switch from the measured value display Select QUICK SETUP menu.
to GROUP SELECTION with F.
GROUP SELECTION MEASURING MODE

Select MEASURING MODE. Select "Pressure" option.
MEASURING MODE
Select "Pressure" option.
GROUP SELECTION
Select QUICK SETUP menu.
POS. ZERO ADJUST (gauge pressure sensors) POS. ZERO ADJUST (gauge pressure sensors)
Due to orientation of the device, there may be a shift in Due to orientation of the device, there may be a shift in
the measured value. You correct the MEASURED the measured value. You correct the MEASURED
VALUE via the POS. ZERO ADJUST parameter with the VALUE via the POS. ZERO ADJUST parameter with the
"Confirm" option, i. e. you assign the value 0.0 to the "Confirm" option, i. e. you assign the value 0.0 to the
pressure present. pressure present.
Endress+Hauser 41
POS. ZERO ADJUST (absolute pressure sensors) POS. ZERO ADJUST (absolute pressure sensors)
the measured value. For the POS. INPUT VALUE the measured value. For the POS. INPUT VALUE
parameter, specify the desired set point for the parameter, specify the desired set point for the
MEASURED VALUE. MEASURED VALUE.
SET LRV SET LRV

Set the measuring range (enter 4 mA value). Set the measuring range (enter 4 mA value).
Specify a pressure value for the lower current value Specify a pressure value for the lower current value
(4 mA value). A reference pressure does not have to be (4 mA value). A reference pressure does not have to be
present at the device. present at the device.
GET LRV GET LRV

Set the measuring range (enter 4 mA value). Set the measuring range (enter 4 mA value).
The pressure for the lower current value (4 mA value) is The pressure for the lower current value (4 mA value) is
present at device. With the "Confirm" option, you assign present at device. With the "Confirm" option, you assign
the lower current value to the pressure value present. the lower current value to the pressure value present.
DAMPING TIME DAMPING TIME

Enter damping time (time constant τ). The damping Enter damping time (time constant τ). The damping
affects the speed at which all subsequent elements, such affects the speed at which all subsequent elements, such
as the on-site display, measured value and current as the on-site display, measured value and current
output react to a change in the pressure. output react to a change in the pressure.
! Note!
For on-site operation, see also page 25, section 5.2.3 "Function of the operating elements" and
page 28, section 5.4 "On-site operation".
42 Endress+Hauser
6.5 Level measurement
6.5.1 Information on level measurement

Three level types are available for level measurement, namely: "Linear", "Pressure Linearized" and
"Height Linearized".
– Linear: select this level type if the measured variable is in direct proportion to the measured
pressure. You can choose between Height, Volume, Mass or % as the measured variable.
– Pressure Linearized: select this level type if the measured variable is not in direct proportion to
the measured pressure such as in the case of containers with a conical outlet. You can choose
between Volume, Mass or % as the measured variable.
– Height Linearized: Select this level type if you need two measured variables or the container shape
is given in value pairs such as height and volume. The following combinations are possible:
"Height + Volume", "Height + Mass", "Height + %", "%-Height + Volume, "%-Height + Mass" or
"%-Height + %". Perform two calibrations for this level type. First for the measured variable Height
or %-Height like for the "Linear" level type and then for the measured variable Volume, Mass or
% like for the "Pressure Linearized" level type.
For the level types "Linear" and "Height Linearized", the calibration modes "wet" and "dry" are
available.
– Wet: wet calibration takes place by filling and emptying the container. Two pressure-level value
pairs have to be entered for this calibration mode. In the case of two different levels, the level
value is entered and the pressure measured at this moment is assigned to the level value.
– Dry: dry calibration is a theoretical calibration which you can carry out even if the device is not
mounted or the container is empty. Depending on the measured variable selected, values for the
parameters needed for the calculation are queried. For example, the density of the fluid must be
entered for the "Level" measured variable.
For the "Pressure Linearized" and "Height Linearized" level type, enter a linearisation table. The
entry modes "Manual" and "Semiautomatic" are available here.
– Manual: the container neither has to be filled nor emptied for this entry mode. Enter the
appropriate value points for the linearisation table.
– Semiautomatic: the container is filled or emptied in stages in this entry mode. The device
automatically records the hydrostatic pressure. Enter the associated volume, mass or %-value.
Endress+Hauser 43
! Note!
• There is a Quick Setup menu for each of the measuring modes Pressure and Level which guides
you through the most important basic functions. With the setting in the MEASURING MODE
parameter, you specify which Quick Setup menu should be displayed. → See also page 39, section
6.2 "Selecting language and measuring mode".
• For a detailed description of the parameters see the Operating Instructions BA274P "Cerabar S/
Deltabar S, Description of device functions"
– Table 6, POSITION ADJUSTMENT
– Table 8 to 11, BASIC SETUP
– Table 14, EXTENDED SETUP
– Table 16, LINEARISATION – On-site operation
– Table 17, LINEARISATION – ToF Tool and HART handheld terminal.
• For level measurement, select the "Level" option by means of the MEASURING MODE
parameter. The operating menu is structured appropriately. → See also section 10.1.
The factory settings for the LEVEL MODE, CALIBRATION MODE, LIN. MEASURAND, EMPTY
CALIB. and FULL CALIB. parameters are as follows:
– FULL CALIB. = 100 %.
6.5.2 Quick Setup menu for Level measuring mode
! Note!
Some parameters of the "Level" measuring mode are only displayed if other parameters are
appropriately configured. For example, the EMPTY PRESSURE parameter is not displayed unless the
"Linear" option was selected for the LEVEL MODE parameter and the "wet" option was selected for
the CALIBRATION MODE parameter (see following figure). You can find the LEVEL MODE
parameter in the BASIC SETTINGS function group (menu path: (GROUP SELECTION →)
OPERATING MENU → SETTINGS → BASIC SETTINGS).
Measured value
1)
GROUP SELECTION
1) 1)
2)
MEASURING MODE
Pressure Level
Gauge pressure sensors Absolut pressure sensors

POS. ZERO ADJUST POS. INPUT VALUE
3) 4)
2) Display via ToF Tool, FieldCare and EMPTY CALIB.
HART handheld terminal only
3) LEVEL MODE = "Pressure Linearized" FULL CALIB.
or "Height Linearized" and/or
CALIBRATION MODE = "dry"
4) LEVEL MODE = "Linear" and
DAMPING VALUE
CALIBRATION MODE = "wet"
Fig. 28: Quick Setup menu for the Level measuring mode
44 Endress+Hauser
Measured value display Measured value display

On-site display: Switch from the measured value display Select QUICK SETUP menu.
to GROUP SELECTION with F.
GROUP SELECTION MEASURING MODE

Select MEASURING MODE. Select "Level" option.
MEASURING MODE
Select "Level" option.
GROUP SELECTION
Select QUICK SETUP menu.
POS. ZERO ADJUST (gauge pressure sensors) POS. ZERO ADJUST (gauge pressure sensors)
the measured value. You correct the MEASURED the measured value. You correct the MEASURED
VALUE via the POS. ZERO ADJUST parameter with the VALUE via the POS. ZERO ADJUST parameter with the
"Confirm" option, i. e. you assign the value 0.0 to the "Confirm" option, i. e. you assign the value 0.0 to the
pressure present. pressure present.
POS. INPUT VALUE (absolute pressure sensors) POS. INPUT VALUE (absolute pressure sensors)
the measured value. For the POS. INPUT VALUE the measured value. For the POS. INPUT VALUE
parameter, specify the desired set point for the parameter, specify the desired set point for the
MEASURED VALUE. MEASURED VALUE.
EMPTY CALIB. (Level mode "linear", Calibration EMPTY CALIB. (Level mode "linear", Calibration
mode "wet") mode "wet")
Enter level for the lower calibration point. Enter level for the lower calibration point.
For this parameter, enter a level value which is assigned For this parameter, enter a level value which is assigned
to the pressure present at the device. to the pressure present at the device.
FULL CALIB. (Level mode "linear", Calibration FULL CALIB. (Level mode "linear", Calibration
mode "wet") mode "wet")
Enter level for the upper calibration point. Enter level for the upper calibration point.
For this parameter, enter a level value which is assigned For this parameter, enter a level value which is assigned
to the pressure present at the device. to the pressure present at the device.
DAMPING TIME DAMPING TIME

Enter damping time (time constant τ). The damping Enter damping time (time constant τ). The damping
affects the speed at which all subsequent elements, such affects the speed at which all subsequent elements, such
as the on-site display, measured value and current as the on-site display, measured value and current
output react to a change in the pressure. output react to a change in the pressure.
! Note!
For on-site operation, see also page 25, section 5.2.3 "Function of the operating elements" and
page 28, section 5.4 "On-site operation".
Endress+Hauser 45
Maintenance Cerabar S PMC71, PMP71/72/75 with 4...20 mA HART
7 Maintenance
Cerabar S requires no maintenance.
7.1 Exterior cleaning

Please note the following points when cleaning the device:
• The cleaning agents used should not attack the surface and the seals.
• Mechanical damage to the membrane, e.g. due to pointed objects, must be avoided.
8 Trouble-shooting
8.1 Messages
The following table lists all the possible messages that can occur.
The device differentiates between the error types "Alarm", "Warning" and "Error". At the factory, all
"Error" type messages are set to "Warning".
→ See "Error type/NA 64" column and section 8.2 "Response of outputs to errors".
In addition, the "Error type/NA 64" column classifies the messages in accordance with NAMUR
Recommendation NA 64:
• Break down: indicated with "B"
• Maintenance need: indicated with "C" (check request)
• Function check: indicated with "I" (in service)
Error message display on the on-site display:
• The measured value display shows the message with the highest priority. → See "Priority"
column.
• The ALARM STATUS parameter shows all the messages present in descending order of priority.
You can scroll through all the messages present with the S-key or O-key.
Message display via the ToF Tool, FieldCare, Commuwin II and HART handheld terminal:
• The ALARM STATUS parameter shows the message with the highest priority. → See "Priority"
column.
! Note!
• For support and further information, please contact Endress+Hauser Service.
• → See also section 8.4, 8.5 and 8.6.
46 Endress+Hauser
Cerabar S PMC71, PMP71/72/75 with 4...20 mA HART Trouble-shooting
Code Error type/ Message/description Cause Measure Priority

NA 64
101 (A101) Alarm B>Sensor electronic EEPROM – Electromagnetic effects are greater – Wait a few minutes. 17
B error than specifications in the technical – Restart the device. Perform reset
data. (→ See section 9.) This (Code 62).
message normally only appears – Block off electromagnetic effects or
briefly. eliminate source of disturbance.
– Sensor defect. – Replace sensor.
102 (W102) Warning C>Checksum error in EEPROM: – Main electronics defect. Correct – Replace main electronics. 53
C peakhold segment measurement can continue as long
as you do not need the peak hold
indicator function.
106 (W106) Warning C>Downloading - please wait – Downloading. – Wait for download to complete. 52
C
110 (A110) Alarm B>Checksum error in EEPROM: – The supply voltage is disconnected – Reestablish supply voltage. Perform 6
B configuration segment when writing. reset (Code 7864) if necessary.
Carry out calibration again.
– Electromagnetic effects are greater – Block off electromagnetic effects or

than specifications in the technical eliminate sources of disturbance.
data.
(→ See section 9.)
– Main electronics defect. – Replace main electronics.
113 (A113) Alarm B>ROM failure in transmitter – Main electronics defect. – Replace main electronics. 1
B electronic
115 (E115) Error C>Sensor overpressure – Overpressure present. – Reduce pressure until message 29
C disappears.
116 (W116) Warning C>Download error, repeat – The file is defect. – Use another file. 36
C download
– During the download, the data are – Check cable connection PC –
not correctly transmitted to the transmitter.
processor, e.g. because of open cable – Block off electromagnetic effects or
connections, spikes (ripple) on the eliminate sources of disturbance.
supply voltage or electromagnetic – Perform reset (Code 7864) and carry
effects. out calibration again.
– Repeat download.
120 (E120) Error C>Sensor low pressure – Pressure too low. – Increase pressure until message 30
C disappears.
121 (A121) Alarm B>Checksum error in factory – Main electronics defect. – Replace main electronics. 5
B segment of EEPROM
122 (A122) Alarm B>Sensor not connected – Cable connection sensor –main – Check cable connection and repair if 13
B electronics disconnected. necessary.
– Electromagnetic effects are greater – Block off electromagnetic effects or

than specifications in the technical eliminate source of disturbance.
data.
130 (A130) Alarm B>EEPROM is defect. – Main electronics defect. – Replace main electronics. 10
B
131 (A131) Alarm B>Checksum error in EEPROM: – Main electronics defect. – Replace main electronics. 9
B min/max segment
132 (A132) Alarm B>Checksum error in totalizer – Main electronics defect. – Replace main electronics. 7
B EEPROM
Endress+Hauser 47
Trouble-shooting Cerabar S PMC71, PMP71/72/75 with 4...20 mA HART

NA 64
133 (A133) Alarm B>Checksum error in History – An error occurred when writing. – Perform reset (Code 7864) and carry 8
B EEPROM out calibration again.
– Main electronics defect. – Replace electronics.
602 (W602) Warning C>Linearisation curve not – The linearisation table is not – Add to linearisation table or perform 57
C monoton monotonic increasing. linearisation again.
604 (W604) Warning C>Linearisation table not valid. At – The linearisation table consists of – Add to linearisation table. If 58
C least 2 points less than 2 points. necessary, perform linearisation
again.
613 (W613) Warning I>Simulation is active – Simulation is switched on, i.e. the – Switch off simulation. 60
I device is not measuring at present.
620 (E620) Error C>Current output out of range The current is outside the permitted – Check pressure applied, reconfigure 49
C range 3.8...20.5 mA. measuring range if necessary (→ See
– The pressure applied is outside the also Operating Instructions BA274P,
chapter 4 to 6 or these Operating
set measuring range (but within the
Instructions, page 2.)
sensor range).
– Perform reset (Code 7864) and carry
out calibration again.
700 (W700) Warning C>Last configuration not stored – An error occurred when writing or – Perform reset (Code 7864) and carry 54
C reading configuration data or the out calibration again.
power supply was disconnected.
701 (W701) Warning C>Measuring chain config. – The calibration carried out would – Carry out calibration again. 50
C exceeds sensor range result in the sensor nominal
operating range being undershot or
overshot.
702 (W702) Warning C>HistoROM data not consistent. – Data were not written correctly to – Repeat upload. 55
C the HistoROM, e.g. if the HistoROM – Perform reset (Code 7864) and carry
was detached during the writing out calibration again.
process.
– HistoROM does not have any data. – Copy suitable data to the HistoROM.
(→ See also page 31, section 5.5.1
"Copying configuration data".)
703 (A703) Alarm B>Measurement error – Fault in the main electronics. – Briefly disconnect device from the 22
B power supply.
B power supply.
B power supply.
706 (W706) Warning C>Configuration in HistoROM – Configuration (parameters) in the – Copy data from the device to the 59
C and device not identical HistoROM and in the device is not HistoROM. (→ See also page 31,
identical. section 5.5.1 "Copying configuration
data".)
– Copy data from the HistoROM to
the device. (→ See also page 31,
section 5.5.1 "Copying configuration
data".) The message remains if the
HistoROM and the device have
different software versions. The
message goes out if you copy the
data from the device to the
HistoROM.
48 Endress+Hauser

NA 64
707 (A707) Alarm B>X-VAL. of lin. table out of edit – At least one X-VALUE in the – Carry out calibration again. (→ See 38
B limits. linearisation table is either below the also Operating Instructions BA274P,
value for HYDR. PRESS MIN. or chapter 5 or these Operating
MIN. LEVEL or above the value for Instructions, page 2.)
HYDR. PRESS. MAX. or LEVEL
MAX.
710 (W710) Warning B>Set span too small. Not – Values for calibration (e.g. lower – Adjust calibration to suit sensor. 51
C allowed. range value and upper range value) (→ See also Operating Instructions
are too close together. BA274P, parameter description
MINIMUM SPAN or these
Operating Instructions, page 2.)
– The sensor was replaced and the – Adjust calibration to suit sensor.
customer-specific configuration does – Replace sensor with a suitable
not suit the sensor. sensor.
– Unsuitable download carried out. – Check configuration and perform

download again.
711 (A711) Alarm B>LRV or URV out of edit limits – Lower range value and/or upper – Reconfigure lower range value and/ 37
B range value undershoot or overshoot or upper range value to suit the
the sensor range limits. sensor. Pay attention to position
factor.
– The sensor was replaced and the – Reconfigure lower range value and/
customer-specific configuration does or upper range value to suit the
not suit the sensor. sensor. Pay attention to position
factor.
– Replace sensor with a suitable
sensor.
download again.
713 (A713) Alarm B>100% POINT level out of edit – The sensor was replaced. – Carry out calibration again. 39
B limits
715 (E715) Error C>Sensor over temperature – The temperature measured in the – Reduce process temperature/ 32
C sensor is greater than the upper ambient temperature.
nominal temperature of the sensor.
(→ See also Operating Instructions
BA274P, parameter description
Tmax SENSOR or these Operating

download again.
716 (A716) Alarm B>Sensor diaphragm broken – Sensor defect. – Replace sensor. 24
B
717 (E717) Error C>Transmitter over temperature – The temperature measured in the – Reduce ambient temperature. 34
C electronics is greater than the upper
nominal temperature of the
electronics (+88 °C).

download again.
718 (E718) Error C>Transmitter under temperature – The temperature measured in the – Increase ambient temperature. 35
C electronics is smaller than the lower Insulate device if necessary.
nominal temperature of the
electronics (–43 °C).

download again.
719 (A719) Alarm B>Y-VAL of lin. table out of edit – At least on Y-VALUE in the – Carry out calibration again. (→ See 40
B limits linearisation table is below the MIN. also Operating Instructions BA274P,
TANK CONTANT or above the chapter 5 or these Operating
MAX. TANK CONTENT. Instructions, page 2.)
Endress+Hauser 49

NA 64
720 (E720) Error C>Sensor under temperature – The temperature measured in the – Increase process temperature/ 33
C sensor is smaller than the lower ambient temperature.
nominal temperature of the sensor.
(→ See also Operating Instructions
BA274P, parameter description
Tmin SENSOR or Operating

download again.
721 (A721) Alarm B>ZERO POSITION level out of – LEVEL MIN or LEVEL MAX has – Perform reset (Code 2710) and carry 41
B edit limits been changed. out calibration again.
722 (A722) Alarm B>EMPTY CALIB. or FULL – LEVEL MIN or LEVEL MAX has – Perform reset (Code 2710) and carry 42
B CALIB. out of edit limits been changed. out calibration again.
723 (A723) Alarm B>MAX. FLOW out of edit limits – FLOW-MEAS. TYPE has been – Carry out calibration again. 43
B changed.
725 (A725) Alarm B>Sensor connection error, cycle – Electromagnetic effects are greater – Block off electromagnetic effects or 25
B disturbance than specifications in the technical eliminate source of disturbance.
data.
– Sensor or main electronics defect. – Replace sensor or main electronics.
726 (E726) Error C>Sensor temperature error - – Electromagnetic effects are greater – Block off electromagnetic effects or 31
C overrange than specifications in the technical eliminate source of disturbance.
data.
(→See section 9.)
– Process temperature is outside – Check temperature present, reduce
permitted range. or increase if necessary.
– Sensor defect. – If the process temperature is within

the permitted range, replace sensor.
727 (E727) Error C>Sensor pressure error - – Electromagnetic effects are greater – Block off electromagnetic effects or 28
C overrange than specifications in the technical eliminate source of disturbance.
data.
– Pressure is outside permitted range. – Check pressure present, reduce or

increase if necessary.
– Sensor defect. – If the pressure is within the

permitted range, replace sensor.
728 (A728) Alarm B>RAM error – Fault in the main electronics. – Briefly disconnect device from the 2
B power supply.

B power supply.
730 (E730) Error C>LRV user limits exceeded – Pressure measured value has – Check system/pressure measured 46
C undershot the value specified for the value.
Pmin ALARM WINDOW parameter. – Change value for Pmin ALARM
WINDOW if necessary. (→ See also
Operating Instructions BA274P,
parameter description Pmin ALARM
WINDOW or these Operating
50 Endress+Hauser

NA 64
731 (E731) Error C>URV user limits exceeded – Pressure measured value has – Check system/pressure measured 45
C overshot the value specified for the value.
Pmax ALARM WINDOW – Change value for Pmax ALARM
parameter. WINDOW if necessary. (→ See also
parameter description Pmax ALARM
732 (E732) Error C>LRV Temp. User limits – Temperature measured value has – Check system/temperature 48
C exceeded undershot the value specified for the measured value.
Tmin ALARM WINDOW parameter. – Change value for Tmin ALARM
WINDOW if necessary. (→ See also
parameter description Tmin ALARM
733 (E733) Error C>URV Temp. User limits – Temperature measured value has – Check system/temperature 47
C exceeded overshot the value specified for the measured value.
Tmax ALARM WINDOW – Change value for Tmax ALARM
parameter. WINDOW if necessary. (→ See also
parameter description Tmax
ALARM WINDOW or these
Operating Instructions, page 2.)
B power supply.
B power supply.
B power supply.
B power supply.
740 (E740) Error C>Calculation overflow, bad – Level measuring mode: the – Check configuration and carry out 27
C configuration measured pressure has undershot calibration again if necessary.
the value for HYDR. PRESS. MIN. or – Select a device with a suitable
overshot the value for HYDR. PRESS measuring range.
MAX.
– Flow measuring mode: the – Check configuration and carry out
measured pressure has undershot calibration again if necessary.
the value for MAX. PRESS FLOW. – Select a device with a suitable
measuring range.
741 (A741) Alarm B>TANK HEIGHT out of edit – LEVEL MIN or LEVEL MAX has – Perform reset (Code 2710) and carry 44
B limits been changed. out calibration again.
742 (A742) Alarm B>Sensor connection error – Electromagnetic effects are greater – Wait a few minutes. 18
B (upload) than specifications in the technical – Perform reset (Code 7864) and carry
data. (→ See section 9.) This out calibration again.
message normally only appears
briefly.
– Cable connection sensor –main – Check cable connection and repair if

electronics disconnected. necessary.
Endress+Hauser 51

NA 64
743 (E743) Alarm B>Electronic PCB error during – This message normally only appears – Wait a few minutes. 14
B initialisation briefly. – Restart the device. Perform reset
(Code 62).
744 (A744) Alarm B>Main electronic PCB error – Electromagnetic effects are greater – Restart the device. Perform reset 11
B than specifications in the technical (Code 62).
data. – Block off electromagnetic effects or
(→ See section 9.) eliminate source of disturbance.
745 (W745) Warning C>Sensor data unknown – Sensor does not suit the device – Replace sensor with a suitable 56
C (electronic sensor nameplate). sensor.
Device continues measuring.
746 (W746) Warning C>Sensor connection error - – Electromagnetic effects are greater – Wait a few minutes. 26
C initialising than specifications in the technical – Restart the device. Perform reset
data. (→ See section 9.) This (Code 7864).
message normally only appears – Block off electromagnetic effects or
briefly. eliminate source of disturbance.
– Overpressure or low pressure – Reduce or increase pressure.

present.
747 (A747) Alarm B>Sensor software not compatible – Sensor does not suit the device – Replace sensor with a suitable 16
B to electronics (electronic sensor nameplate). sensor.
748 (A748) Alarm B>Memory failure in signal – Electromagnetic effects are greater – Block off electromagnetic effects or 15
B processor than specifications in the technical eliminate source of disturbance.
data.
(→See section 9.)
52 Endress+Hauser
8.2 Response of outputs to errors

The device differentiates between the error types Alarm, Warning and Error.
→ See the following table and page 46, section 8.1 "Messages".
Output A (Alarm) W (Warning) E (Error: Alarm/Warning)
Current output Assumes the value specified via the Device continues measuring. For this error, you can enter whether the
OUTPUT FAIL MODE1, ALT. CURR. device should react as in the event of an
OUTPUT1 and SET MAX. ALARM1 alarm or as in the event of a warning. See
parameter. → See also the following section corresponding "Alarm" or "Warning"
"Configuring current output for an alarm". column. (→ See also Operating Instructions
BA274P, parameter description SELECT
ALARM TYPE or these Operating
Bar graph → See this table, current output. → See this table, current output. → See this table, current output.
(on-site display)
On-site display – The measured value and message are – The measured value and message are – The measured value and message are
displayed alternately displayed alternately displayed alternately
– Measured value display: -symbol is – Measured value display: -symbol – Measured value display: see
permanently displayed. flashes. corresponding "Alarm" or "Warning"
column
Message display Message display: Message display:
– 3-digit number such as A122 and – 3-digit number such as W613 and – 3-digit number such as E731 and
– Description – Description – Description
Remote operation In the case of an alarm, the In the case of a warning, the ALARM In the case of an error, the
(ToF Tool, FieldCare, ALARM STATUS2 parameter displays a 3- STATUS2 parameter displays a 3-digit ALARM STATUS2 parameter displays a 3-
Commuwin II or HART digit number such as 122 for "Sensor not number such as 613 for "Simulation is digit number such as 731 for "URV user
handheld terminal) connected". active". limits exceeded".
1) Menu path: (GROUP SELECTION →) OPERATING MENU → OUTPUT

2) Menu path: (GROUP SELECTION →) OPERATING MENU → MESSAGES
8.2.1 Configuring current output for an alarm

You can configure the current output for the event of an alarm by means of the OUTPUT FAIL
MODE, ALT. CURR. OUTPUT and SET MAX. ALARM parameters.
In the event of an alarm, the current and the bargraph assume the value entered with the OUTPUT
FAIL MODE parameter.
I
max.
➀ 21...23 mA
min.
➂ 3.6 mA
t
P01-xxxxxxxx-05
Fig. 29: Current output in the event of an alarm

Options:
1 Max. alarm (110%): can be set between 21...23 mA via the SET MAX. ALARM parameter
2 Hold meas. value: last measured value is kept
3 Min. alarm (–10%): 3.6 mA
Factory setting: OUTPUT FAIL MODE = max., SET MAX. ALARM = 22 mA
Endress+Hauser 53
Use the ALT. CURR. OUTPUT parameter to set the current output value for the error messages E
120 "Sensor low pressure" and E 115 "Sensor overpressure". You have the following options:
– Normal: the current output assumes the value set via the OUTPUT FAIL MODE and SET MAX.
ALARM parameters.
– NAMUR
– Lower sensor limit undershot (E 120 "Sensor low pressure"): 3.6 mA
– Upper sensor limit overshot (E 115 "Sensor overpressure") overshot: current output assumes
the value set via the SET MAX ALARM parameter.
Factory setting: ALT. CURR. OUTPUT = normal
8.3 Confirming messages

Depending on the settings for the ALARM DISPL. TIME and ACK. ALARM MODE parameters, the
following measures should be taken to clear a message:
Settings 1 Measures
– ALARM DISPL. TIME = 0 s – Rectify cause of the message (see also Section 8.1).
– ACK. ALARM MODE = off
– ALARM DISPL. TIME > 0 s – Rectify cause of the message (see also Section 8.1).
– ACK. ALARM MODE = off – Wait for the alarm display time to elapse.
– ALARM DISPL. TIME = 0 s – Rectify cause of the message (see also Section 8.1).
– ACK. ALARM MODE = on – Confirm message using ACK. ALARM parameter.
– ALARM DISPL. TIME > 0 s – Rectify cause of the message (see also Section 8.1).
– ACK. ALARM MODE = on – Confirm message using ACK. ALARM parameter.
– Wait for the alarm display time to elapse. If a message appears and the alarm
display time elapses before the message has been acknowledged, the message
will be cleared once it has been acknowledged.
1) Menu path for ALARM DISPL. TIME and ACK. ALARM MODE: (GROUP SELECTION →) OPERATING MENU →
DIAGNOSTICS → MESSAGES
If the on-site display displays a message, you can delete it with the F-key.
If there are several messages, the on-site display shows the message which has the highest priority
(see also Section 8.1). Once you have deleted this message using the F-key, the message with the
next highest priority is displayed. You can use the F-key to delete each message, one after the other.
The ALARM STATUS parameter continues to display all the messages present.
54 Endress+Hauser
8.4 Repair
The Endress+Hauser repairs concept provides for measuring devices to have a modular design and
also the customer may carry out repairs.
Section "Spare parts" contains all the spare parts listed with their order numbers. You can order them
from Endress+Hauser for repairs on your Cerabar S. As far as necessary, the spare parts also include
replacement instructions.
! Note!
• For certified devices, please consult Chapter "Repair of Ex-certified devices".
• For more information on service and spare parts contact the Endress+Hauser Service. ( → See
www.endress.com/worldwide)
8.5 Repair of Ex-certified devices

# Warning!
When repairing Ex-certified devices, please note the following:
• Only specialist personnel or Endress+Hauser may undertake repairs of certified devices.
• Relevant standards, national hazardous area regulations and Safety Instructions (XA...) and
Certificates must be observed.
• Only genuine Endress+Hauser spare parts may be used.
• When ordering spare parts, please check the device designation on the nameplate. Identical parts
may only be used as replacements.
• Electronic inserts or sensors already in use in a standard instrument may not be used as spare parts
for a certified device.
• Carry out repairs according to the instructions. After repairs, the device must fulfil the
requirements of the specified individual tests.
• A certified device may only be converted into another certified variant by Endress+Hauser.
• All repairs and modifications must be documented.
Endress+Hauser 55
8.6 Spare Parts

The following pages list all the spare parts with order numbers which you can order from
Endress+Hauser to repair the Cerabar S.
When ordering spare parts, always quote the serial number indicated on the nameplate. The spare
parts number is embossed on every spare part. As far as necessary, the spare parts also include
replacement instructions.
You can order sensor modules as spare parts for PMC71 and PMP71. For PMC71 and PMP71, see
page 60 and page 63 respectively.
The right order number for the sensor module is derived from the Order No. which is indicated on
the nameplate (→ see also page 6).
10 20 30 40 50 60 70 80 90 100 110
Order code/Order No. of the device
PMC71 – ❑ ❑ ❑ ❑❑ ❑ ❑ ❑❑ ❑ ❑ ❑ ❑ see name plate
PMP71 –
PMC71X – ❑ ❑❑ ❑❑ ❑ ❑ ❑ Order code sensor module
PMP71X – ❑ ❑❑ ❑ ❑❑ ❑ ❑ ❑ Order code sesnor module
Fig. 30: Order code device or order code sensor module

10 Approval
20 Output; Operation
30 Housing; Cable entry; Protection
40 Sensor range; OPL
50 Calibration; Unit
60 Membrane material (PMC71 only)
70 Process connection; Material
80 Seal
90 Fill fluid (PMP71 only)
100 Additional option 1
110 Additional option 2
56 Endress+Hauser
8.6.1 Spare parts for PMC71, PMP71, PMP72, PMP75

See the following pages for process connections and sensors.
20
21
20
21
40
31
30
15
13
10
12
35
21
25
Endress+Hauser 57
10 Housing (with retaining ring and housing seal, without cover)

52020430 Aluminium T14 housing, M20x1.5, not for EEx d/XP
52020488 Aluminium T14 housing, M20x1.5, HART, with 3 push buttons external, not for EEx d/XP
52020489 Aluminium T14 housing, PROFIBUS PA/Foundation Fieldbus, with push button external,
not for EEx d/XP
52020431 Aluminium T14 housing, 1/2 NPT, not for EEx d/XP
52020490 Aluminium T14 housing, 1/2 NPT, HART, with 3 push buttons external, not for EEx d/XP
52020491 Aluminium T14 housing, 1/2 NPT, PROFIBUS PA/Foundation Fieldbus, with push button external,
not for EEx d/XP
12 Mounting set housing/sensor

52020440 Mounting set housing/sensor consists of: 2 O-rings 45.69x2.62 EPDM + retaining ring
13 Push buttons housing, HART

52024110 Push buttons, consists of: push buttons, cover and screws (version 2.0)
15 Cable entry/cable gland

52020760 Cable gland M20x1.5, gasket
52020761 Cable entry G 1/2, gasket, adapter
52020762 Plug 2/7pole, Han7D, gasket
52020763 Plug 3pole, M12, gasket
20 Cover
52020432 Cover for Aluminium T14 housing incl. gasket, not for EEx d/XP
52020433 Cover for Aluminium T14 housing incl. gasket, for EEx d/XP
52028310 Cover for AISI 316L T14 housing incl. gasket
52020494 Cover for Aluminium T14 housing with sight glass incl. gasket, Ex-free
52020492 Cover for Aluminium T14 housing with sight glass incl. gasket, not for EEx d/XP
52020493 Cover for Aluminium T14 housing with sight glass incl. gasket, for EEx d/XP
71002811 Cover for AISI 316L T17 housing with sight glass incl. gasket, for Ex-free area, 1/2 G EEx ia, 3 G EEx nA, IS, NI
71002810 Cover for AISI 316L T17 housing with sight glass incl. gasket, for 1/2 D, 1/3 D, 1 GD, 1/2 GD, DIP, Dust Ex
21 Sealing for cover

52020429 Sealing set EPDM for cover Aluminium T14 housing (5 pieces)
25 Cover for terminal compartment

52020432 Cover for Aluminium T14 housing incl. gasket, not for EEx d/XP
52020433 Cover for Aluminium T14 housing incl. gasket, for EEx d/XP
30 Electronics
52024400 Electronics 4...20 mA, HART, Ex, version 2.0x, push button on electronics
52024111 Electronics 4...20 mA, HART, Ex, version 2.0x, push button on housing
31 HistoROM/M-DAT
52027785 HistoROM/M-DAT, ToF Tool-CD included
35 Terminal block
52020434 Terminal 3-pole, RFI-filter 4...20 mA, HART Ex ia
52020436 Terminal 3-pole, RFI-filter 4...20 mA, HART Ex d
40 Display module
71002865 Display module VU340 HART with 3 push buttons and holder
58 Endress+Hauser
8.6.2 Spare parts for PMC71
12
50 50 50
57
55 57
57
58
P01-PMC71xxx-09-xx-xx-xx-000
55 Process adapter PMC71

52020215 Thread JIS B0202 PF 1/2 (external), AISI 316L
52020216 Thread ISO 228 G 1/2 A G 1/4 (internal), AISI 316L
52020217 Thread ISO 228 G 1/2 A drill hole 11.4 mm, AISI 316L
52020218 Thread JIS B0203 PT 1/2 (external), AISI 316L
52020219 Thread ANSI 1/2 MNPT, AISI 316L
52020220 Thread ANSI 1/2 MNPT 1/4 FNPT, AISI 316L
52020221 Thread DIN 13 M 20x1.5 drill hole 11.4 mm, AISI 316L
52020222 Thread G 1/2 A EN 837, AISI 316L
Process adapter PMC71 with material test certificate for wetted parts, inspection certificate EN 10204 3.1 as per
specification 52005759
52020223 Thread JIS B0202 PF 1/2 (external), AISI 316L
52020224 Thread ISO 228 G 1/2 A G 1/4 (internal), AISI 316L
52020225 Thread ISO 228 G 1/2 A drill hole 11.4 mm, AISI 316L
52020226 Thread JIS B0203 PT 1/2 (external), AISI 316L
52020227 Thread ANSI 1/2 MNPT, AISI 316L
52020228 Thread ANSI 1/2 MNPT 1/4 FNPT, AISI 316L
52020229 Thread DIN 13 M 20x1.5 drill hole 11.4 mm, AISI 316L
52020230 Thread G 1/2 A EN 837, AISI 316L
57 Process gasket
52020768 O-ring 26.7x1.78 FKM 70 Viton, oil and grease free (5 pieces)
52020769 O-ring 26.7x1.78 NBR 70 (5 pieces)
52020770 O-ring 26.7x1.78 EPDM 70 (5 pieces)
52020771 O-ring 26.7x1.78 FKM Viton –40°C (5 pieces)
52020772 O-ring 26.7x1.78 FFKM 70 Kalrez (1 piece)
52020773 O-ring 26.7x1.78 FFKM 75 Chemraz (1 piece)
58 Fastening angle
52020441 Mounting angle, adapter and screws
Endress+Hauser 59
Sensor module for Cerabar S PMC71
10 Approval:
A For non-hazardous areas
1 ATEX II 1/2 G EEx ia IIC T6
6 ATEX II 1/2 G EEx ia IIC T6, overspill protection WHG
2 ATEX II 1/2 D
8 ATEX II 1 GD EEx ia II T6
3 ATEX II 1/3 GD EEx ia IIC T6
4 ATEX II 1/3 D
7 ATEX II 3 G EEx nA II T6
S FM IS, Class I, II, III Division 1, Groups A – G; NI Class I Division 2, Groups A – D; AEx ia
Q FM DIP, Class II, III Division 1, Groups E – G
R FM NI, Class I, Division 2, Groups A – D
U CSA IS, Class I, II, III Division 1, Groups A – G; Class I Division 2, Groups A – D, Ex ia
40 Sensor range; OPL:

Sensors for gauge pressure
Measurement limits: –100 % (–1 bar)...+100 % of sensor nominal range
Sensor nominal value (URL) OPL (Over pressure limit)
1C 100 mbar/10 kPa/1.5 psi g 4 bar/400 kPa/60 psi g
1E 250 mbar/25 kPa/3.8 psi g 5 bar/500 kPa/75 psi g
1F 400 mbar/40 kPa/6 psi g 8 bar/800 kPa/120 psi g
1H 1 bar/100 kPa/15 psi g 10 bar/1 Mpa/150 psi g
1K 2 bar/200 kPa/30 psi g 18 bar/1,8 MPa/270 psi g
1M 4 bar/400 kPa/60 psi g 25 bar/2,5 MPa/375 psi g
1P 10 bar/1 MPa/150 psi g 40 bar/4 MPa/600 psi g
1S 40 bar/4 MPa/600 psi g 60 bar/6 MPa/900 psi g
Sensors for absolute pressure
2C 100 mbar/10 kPa/1.5 psi abs 4 bar/400 kPa/60 psi abs
2E 250 mbar/25 kPa/3.8 psi abs 5 bar/500 kPa/75 psi abs
2F 400 mbar/40 kPa/6 psi abs 8 bar/800 kPa/120 psi abs
2H 1 bar/100 kPa/15 psi abs 10 bar/1 MPa/150 psi abs
2K 2 bar/200 kPa/30 psi abs 18 bar/1,8 MPa/270 psi abs
2M 4 bar/400 kPa/60 psi abs 25 bar/2,5 MPa/375 psi abs
2P 10 bar/1 MPa/150 psi abs 40 bar/4 MPa/600 psi abs
2S 40 bar/4 MPa/600 psi abs 60 bar/6 MPa/900 psi abs
70 Process connection, material:

Thread, inner diaphragm
GA Thread ISO 228 G 1/2 A EN 837, AISI 316L
GB Thread ISO 228 G 1/2 A EN 837, Alloy C
GC Thread ISO 228 G 1/2 A EN 837, Monel
GD Thread ISO 228 G 1/2 A EN 837, PVDF (max. 15bar/225 psi, –10...+60 °C)
GE Thread ISO 228 G 1/2 A G 1/4 (female), AISI 316L
GF Thread ISO 228 G 1/2 A G 1/4 (female), Alloy C
GG Thread ISO 228 G 1/2 A G 1/4 (female), Monel
GH Thread ISO 228 G 1/2 A hole 11.4 mm, AISI 316L
GJ Thread ISO 228 G 1/2 A hole 11.4 mm, Alloy C
GK Thread ISO 228 G 1/2 A hole 11.4 mm, Monel
RA Thread ANSI 1/2 MNPT 1/4 FNPT, AISI 316L
RB Thread ANSI 1/2 MNPT 1/4 FNPT, Alloy C
RC Thread ANSI 1/2 MNPT 1/4 FNPT, Monel
RD Thread ANSI 1/2 MNPT, AISI 316L
RE Thread ANSI 1/2 MNPT, Alloy C
RF Thread ANSI 1/2 MNPT, Monel
RG Thread ANSI 1/2 MNPT hole 3 mm, PVDF
(max. 15 bar/225 psi, –10...+60 °C)
RH Thread ANSI 1/2 FNPT, AISI 316L
RJ Thread ANSI 1/2 FNPT, Alloy C
RK Thread ANSI 1/2 FNPT, Monel
GL Thread JIS B0202 PF 1/2 (male), AISI 316L
RL Thread JIS B0203 PT 1/2 (male), AISI 316L
GP Thread DIN 13 M 20x1.5 hole 11.4 mm, AISI 316L
GQ Thread DIN 13 M 20x1.5 hole 11.4 mm, Alloy C
For continuation of "Process connection, material" see next page
PMC71X order code
60 Endress+Hauser
Sensor module for Cerabar S PMC71 (continuation)
70 Process connection, material

Thread, flush-mounted diaphragm
1G Thread ISO 228 G 1 1/2 A, AISI 316L
1H Thread ISO 228 G 1 1/2 A, Alloy C
1J Thread ISO 228 G 1 1/2 A, Monel
1K Thread ISO 228 G 2 A, AISI 316L
1L Thread ISO 228 G 2 A, Alloy C
1M Thread ISO 228 G 2 A, Monel
2D Thread ANSI 1 1/2 MNPT, AISI 316L
2E Thread ANSI 1 1/2 MNPT, Alloy C
2F Thread ANSI 1 1/2 MNPT, Monel
2G Thread ANSI 2 MNPT, AISI 316L
2H Thread ANSI 2 MNPT, Alloy C
2J Thread ANSI 2 MNPT, Monel
1R Thread DIN 13 M 44x1.25, AISI 316L
1S Thread DIN 13 M 44x1.25, Alloy C
EN/DIN flanges, flush-mounted diaphragm
CP DN 32 PN 25/40 B1, AISI 316L
CQ DN 40 PN 25/40 B1, AISI 316L
BR DN 50 PN 10/16 A, PVDF (max. 10 bar/150 psi, –10...+60 °C)
B3 DN 50 PN 25/40 A, AISI 316L
C3 DN 50 PN 63 B1, AISI 316L
BS DN 80 PN 10/16 A, PVDF (max. 10 bar/150 psi, –10...+60 °C)
B4 DN 80 PN 25/40 A, AISI 316L
ANSI flanges, flush-mounted diaphragm
AE 1 1/2" 150 lbs RF, AISI 316/316L
AQ 1 1/2" 300 lbs RF, AISI 316/316L
AF 2" 150 lbs RF, AISI 316/316L
JR 2" 150 lbs RF, AISI 316L with ECTFE-coating
A3 2" 150 lbs RF, PVDF (max. 10 bar/150 psi, –10...+60 °C)
AR 2" 300 lbs RF, AISI 316/316L
AG 3" 150 lbs RF, AISI 316/316L
JS 3" 150 lbs RF, AISI 316L with ECTFE-coating
A4 3" 150 lbs RF, PVDF (max. 10 bar/150 psi, –10...+60 °C)
AS 3" 300 lbs RF, AISI 316/316L
AH 4" 150 lbs RF, AISI 316/316L
JT 4" 150 lbs RF, AISI 316L with ECTFE-coating
AT 4" 300 lbs RF, AISI 316/316L
JIS flange, flush-mounted diaphragm
KF 10K 50A RF, AISI 316L
KL 10K 80A RF, AISI 316L
KH 10K 100A RF, AISI 316L
without process connection
0A without process connection for thread, interchangeable threaded boss
0B without process connection for thread, flush-mounted
0C without process connection for flange, flush-mounted
80 Seal:
A FKM Viton
B EPDM
D Kalrez
E Chemraz
F NBR
1 FKM Viton, oxygen service
100 Additional options 1:

A Additional options 1 not selected
B Material test certificate for wetted parts, inspection certificate as per EN 10204 3.1 acc. to
M Overvoltage protection
V Mounting on shut-off valve from above
N HistoROM/M-DAT
S GL (German Lloyd) marine certificate
2 Test report acc. to EN 10204 2.2
3 Routine test with certificate, inspection certificate as per EN 10204 3.1
4 Overpressure test with certificate, inspection certificate as per EN 10204 3.1
PMC71X order code
Endress+Hauser 61
Sensor module for Cerabar S PMC71 (continuation)

2 Test report acc. to EN10204 2.2
5 Helium leak test EN 1518 with test certificate, inspection certificate as per EN 10204 3.1
PMC71X order code sensor module with process connection
PMC71X 0A A A order code sensor module without process connection

0B
0C
62 Endress+Hauser
8.6.3 Spare parts for PMP71PMP71
12
50
Sensor module for Cerabar S PMP71
10 Approval:
A For non-hazardous areas
1 ATEX II 1/2 G EEx ia IIC T6
6 ATEX II 1/2 G EEx ia IIC T6, overspill protection WHG
2 ATEX II 1/2 D
4 ATEX II 1/3 D
8 ATEX 1 GD EEx ia IIC T6
5 ATEX II 2 G EEx d IIC T6
7 ATEX II 3 G EEx nA II T6
S FM IS, Class I, II, III Division 1, Groups A – G; NI Class I Division 2, Groups A – D; AEx ia
T FM XP, Class I Division 1, Groups A – D; AEx d
Q FM DIP, Class II, III Division 1, Groups E – G
R FM NI, Class I, Division 2, Groups A – D
U CSA IS, Class I, II, III Division 1, Groups A – G; Class I Division 2, Groups A – D, Ex ia
V CSA XP Class I Division 1, Groups B – D; Ex d
W CSA Class II, III Division 1, Groups E – G (Dust-Ex)
3 Combi-certificate: ATEX II 1/2 GD EEx ia IIC T6
C Combi-certificate: FM IS and XP Class I Division 1, Groups A – D
D Combi-certificate: CSA IS and XP Class I Division 1, Groups A – D
E Combi-certificate: FM/CSA IS and XP Class I Division 1, Groups A – D
40 Sensor range; OPL:

Sensors for gauge pressure
Measurement limits: –100 % (–1 bar)...+100 % of sensor nominal range
1C 100 mbar/10 kPa/1.5 psi g 4 bar/400 kPa/60 psi g
1E 250 mbar/25 kPa/3.8 psi g 4 bar/400 kPa/60 psi g
1F 400 mbar/40 kPa/6 psi g 6 bar/600 kPa/90 psi g
1H 1 bar/100 kPa/15 psi g 10 bar/1 MPa/150 psi g
1K 2 bar/200 kPa/30 psi g 20 bar/2 MPa/300 psi g
1M 4 bar/400 kPa/60 psi g 28 bar/2.8 MPa/420 psi g
1P 10 bar/1 MPa/150 psi g 40 bar/4 MPa/600 psi g
1S 40 bar/4 MPa/600 psi g 160 bar/16 MPa/2400 psi g
1U 100 bar/10 MPa/1500 psi g 400 bar/40 MPa/6000 psi g
1W 400 bar/40 MPa/6000 psi g 600 bar/60 MPa/9000 psi g
1X 700 bar/70 MPa/10500 psi g 1050 bar/105 MPa/15700 psi g
For continuation "Sensor range; OPL" see next page.
PMP71X order code
Endress+Hauser 63
Sensor module for Cerabar S PMP71 (continuation)
40 Sensor range; OPL (continued):

Sensors for absolute pressure
2C 100 mbar/10 kPa/1.5 psi abs 4 bar/400 kPa/60 psi abs
2E 250 mbar/25 kPa/3.8 psi abs 4 bar/400 kPa/60 psi abs
2F 400 mbar/40 kPa/6 psi abs 6 bar/600 kPa/90 psi abs
2H 1 bar/100 kPa/15 psi abs 10 bar/1 MPa/150 psi abs
2K 2 bar/200 kPa/30 psi abs 20 bar/2 MPa/300 psi abs
2M 4 bar/400 kPa/60 psi abs 28 bar/2.8 MPa/420 psi abs
2P 10 bar/1 MPa/150 psi abs 40 bar/4 MPa/600 psi abs
2S 40 bar/4 MPa/600 psi abs 160 bar/16 MPa/2400 psi abs
2U 100 bar/10 MPa/1500 psi g 400 bar/40 MPa/6000 psi g
2W 400 bar/40 MPa/6000 psi g 600 bar/60 MPa/9000 psi g
2X 700 bar/70 MPa/10500 psi g 1050 bar/105 MPa/15700 psi g
60 Membrane material:
1 AISI 316L
2 Alloy C276
70 Process connection; material:

Thread, inner diaphragm
GA Thread ISO 228 G 1/2 A EN 837, AISI 316L
GB Thread ISO 228 G 1/2 A EN 837, Alloy C
GE Thread ISO 228 G 1/2 A G 1/4 (female), AISI 316L
GF Thread ISO 228 G 1/2 A G 1/4 (female), Alloy C
GH Thread ISO 228 G 1/2 A hole 11.4 mm, AISI 316L
GJ Thread ISO 228 G 1/2 A hole 11.4 mm, Alloy C
RA Thread ANSI 1/2 MNPT 1/4 FNPT, AISI 316L
RB Thread ANSI 1/2 MNPT 1/4 FNPT, Alloy C
RD Thread ANSI 1/2 MNPT, AISI 316L
RE Thread ANSI 1/2 MNPT, Alloy C
RH Thread ANSI 1/2 FNPT, AISI 316L
RJ Thread ANSI 1/2 FNPT, Alloy C
GL Thread JIS B0202 PF 1/2 (male), AISI 316L
RL Thread JIS B0203 PT 1/2 (male), AISI 316L
GP Thread DIN 13 M 20x1.5 hole 11.4 mm, AISI 316L
GQ Thread DIN 13 M 20x1.5 hole 11.4 mm, Alloy C
Thread, flush-mounted diaphragm
1A Thread ISO 228 G 1/2 A, DIN 3852, AISI 316L
1B Thread ISO 228 G 1/2 A, DIN 3852, Alloy C
1D Thread ISO 228 G 1 A, AISI 316L
1E Thread ISO 228 G 1 A, Alloy C
1G Thread ISO 228 G 1 1/2 A, AISI 316L
1H Thread ISO 228 G 1 1/2 A, Alloy C
1K Thread ISO 228 G 2 A, AISI 316L
1L Thread ISO 228 G 2 A, Alloy C
2A Thread ANSI 1 MNPT, AISI 316L
2B Thread ANSI 1 MNPT, Alloy C
2D Thread ANSI 1 1/2 MNPT, AISI 316L
2E Thread ANSI 1 1/2 MNPT, Alloy C
2G Thread ANSI 2 MNPT, AISI 316L
2H Thread ANSI 2 MNPT, Alloy C
1N Thread DIN 16288 M 20x1.5, AISI 316L
1P Thread DIN 16288 M 20x1.5, Alloy C
1R Thread DIN 13 M 44x1.25, AISI 316L
1S Thread DIN 13 M 44x1.25, Alloy C
EN/DIN flanges, flush-mounted diaphragm
CN DN 25 PN 10-40 B1, AISI 316L
CP DN 32 PN 25/40 B1, AISI 316L
CQ DN 40 PN 25/40 B1, AISI 316L
B3 DN 50 PN 25/40 A, AISI 316L
B4 DN 80 PN 25/40 A, AISI 316L
For continuation of "Process connection, material" see next page.
PMP71X order code
64 Endress+Hauser
Sensor module for Cerabar S PMP71 (continuation)
70 Process connection; material (continued):

ANSI flanges, flush-mounted diaphragm
AN 1" 300 lbs RF, AISI 316/316L
AE 1 1/2" 150 lbs RF, AISI 316/316L
AQ 1 1/2" 300 lbs RF, AISI 316/316L
AF 2" 150 lbs RF, AISI 316/316L
AG 3" 150 lbs RF, AISI 316/316L
AS 3" 300 lbs RF, AISI 316/316L
AH 4" 150 lbs RF, AISI 316/316L
AT 4" 300 lbs RF, AISI 316/316L
JIS flanges, flush-mounted diaphragm
KA 20K 25A RF, AISI 316L
KF 10K 50A RF, AISI 316L
KL 10K 80A RF, AISI 316L
KH 10K 100A RF, AISI 316L
Other
UR Ovalflange adapter 1/4-18 NPT, mounting: 7/16-20 UNF, AISI 316L
U1 Prepared for diaphragm seal mount, AISI 316L
90 Fill fluid:
A Silicone
F Inert oil

B Material test certificate for wetted parts, inspection certificate as per EN 10204 3.1 acc. to
C NACE MR0175 material
D Material test certificate for wetted parts as per EN 10204 3.1 and NACE MR0175 material,
inspection certificate as per EN 10204 acc. to specification 52010806

M Overvoltage protection
N HistoROM/M-DAT
5 Helium leak test EN 1518 with test certificate,
inspection certificate as per EN 10204 3.1
PMP71X order code
8.7 Returning the device

Before you send in a device for repairs or checking:
• Remove all signs of fluids, paying particular attention to seal grooves and gaps in which fluid can
become lodged. This is especially important if the fluid is hazardous to health. Please refer also to
the "Declaration of Contamination".
Please enclose the following when returning the device:
• Please fill out completely and sign the "Declaration of Contamination".
It is only then possible for Endress+Hauser to inspect or repair the returned device.
• The chemical and physical properties of the fluid.
• A description of the application.
• A description of the error which occurred.
• Special instructions on handling, if necessary, e.g. safety data sheet as per
EN 91/155/EEC.
Endress+Hauser 65
8.8 Disposal
When disposing, separate and recycle the device components based on the materials.
8.9 Software history
Software version/ Changes software Changes documentation

valid as of
01.00/01.10.2003 Orginal software.

Compatible with:
– ToF Tool Field Tool Package, version 1.04.00 or higher
– Commuwin II version 2.08.-1, Update G or higher
– HART Communicator DXR375
with Device Rev.: 10, DD Rev.: 1
02.00/05.2004 – Number of parameters in the Quick Setup menus has been – Documentation changed to reflect changes to the software.
reduced. – The "Description of Parameters" Section has been moved to the
– On-site operation: LANGUAGE and MEASURING MODE Operating Instructions BA274P.
parameters have been moved to the top level.
– New SAFETY CONFIRM. group implemented for SIL.
→ See also SD190P Safety Manual Cerabar S.
– MEASURING MODE "Level", LEVEL MODE "Linear": AREA
UNIT and TANK SECTION parameters have been replaced with
the TANK VOLUME and TANK HEIGHT parameters.
– Function of the SIMULATED VALUE parameter has been split
across six parameters.
– SENSOR TRIM and CURRENT TRIM groups have been
removed.
– Sensor adapt reset, code 1209 and sensor calibration reset, code
2509 have been removed.
– Quick Setup menus are available via ToF Tool.
Compatible with:
– ToF Tool Field Tool Package version 2.00.00 or higher
– Commuwin II version 2.08.-1, Update > G
– HART Communicator DXR375
with Device Rev.: 20, DD Rev.: 1
02.01/06.2005 – Operating keys also integrated on the optional on-site display. – Section 5.1 "On-site display" changed.
– Chinese and Japanese are available as the menu language on – Section 6.2 "Selecting language and measuring mode" changed.
request.
Compatible with:
– ToF Tool Field Tool Package version 3.00.00 or higher
– FieldCare version 2.01.00, DTM Library version 2.06.00,
DTM: Cerabar S/PMx7x/V02.00 V 1.4.98.74*
– Commuwin II version 2.08.-1, Update > G*
– HART Communicator DXR375 with Device Rev.: 20,
DD Rev.: 1*
* Menu languages Chinese and Japanese not selectable
66 Endress+Hauser
Cerabar S PMC71, PMP71/72/75 with 4...20 mA HART Technical data
9 Technical data
For technical data, please refer to the Technical Information TI383P for Cerabar S.
10 Appendix
10.1 Operating menu for on-site display, ToF Tool,

FieldCare and HART handheld terminal
! Note!
• The entire menu is depicted on the following pages.
• The menu has a different structure depending on the measuring mode selected. This means that
some function groups are only displayed for one measuring mode, e.g. "LINEARISATION"
function group for the Level measuring mode.
• In addition, there are also parameters that are only displayed if other parameters are appropriately
configured. For example the Customer Unit P parameter is only displayed if the "User unit" option
was selected for the PRESS. ENG. UNIT parameter. These parameters are indicated with a "*".
• For a description of the parameters, please refer to Operating Instructions BA274P "Description
of device functions". The exact dependency of individual parameters on one another is explained
here. See also page 2, section "Overview documentation".
Endress+Hauser 67
Appendix Cerabar S PMC71, PMP71/72/75 with 4...20 mA HART
Measured value
1)
GROUP SELECTION
1) 1)
SETTINGS
POSITION ADJUSTMENT BASIC SETUP
2)
MEASURING MODE
PRESS. ENG. UNIT
CUSTOMER UNIT P
*
2)
CUST. UNIT FACT. P
*
MEASURING MODE
Pressure Level Pressure Level

3) 3)
POS. ZERO ADJUST POS. ZERO ADJUST POS. ZERO ADJUST SET LRV LEVEL MODE
4) 4)
POS. INPUT VALUE POS. INPUT VALUE POS. INPUT VALUE SET URV Continuation,
see the following page
SET LRV EMPTY CALIB.
* CALIB. OFFSET GET LRV
X
SET URV FULL CALIB.
* GET URV
DAMPING VALUE DAMPING VALUE DAMPING VALUE

2) Display via ToF Tool, FieldCare and
3) Gauge pressure sensors
4) Absolut pressure sensors
* There are parameters that are only displayed

if other parameters are appropriately configured.
For example the CUSTOMER UNIT P parameter is only displayed
if the "User unit" option was selected for the PRESS. ENG. UNIT parameter.
These parameters are indicated with a "*".
68 Endress+Hauser
Cerabar S PMC71, PMP71/72/75 with 4...20 mA HART Appendix
Height Volume Mass %
HEIGHT UNIT UNIT VOLUME MASS UNIT

X
Continuation
BASIC SETUP "Level",
CUTOMER UNIT H * CUSTOMER UNIT V * CUSTOMER UNIT M *
see also the previous page
Level CUST. UNIT FACT. H * CUST. UNIT FACT. V * CUST. UNIT FACT. M *
D D D D
LEVEL MODE
Pressure Height
Linear
Linearized Linearized E
LIN. MEASURAND LINd MEASURAND COMB. MEASURAND Volume Mass %
UNIT VOLUME MASS UNIT

C E G
D F H CUSTOMER UNIT V * CUSTOMER UNIT M *
CALIBRATION MODE HYDR. PRESS MIN.

CUST. UNIT FACT. V * CUST. UNIT FACT. M *
E
HYDR. PRESS MAX. F F F F

wet dry
EMPTY CALIB. DENSITY UNIT DAMPING VALUE LEVEL MIN
EMPTY PRESSURE ADJUST DENSITY LEVEL MAX G
FULL CALIB. TANK VOLUME * CALIBRATION MODE

Height+... %Height+...
FULL PRESSURE TANK HEIGHT * HEIGHT UNIT

wet dry
ADJUSTED DENSITY * HEIGHT UNIT * EMPTY CALIB. DENSITY UNIT CUTOMER UNIT H *
CUSTOMER UNIT H * EMPTY PRESSURE ADJUST DENSITY CUST. UNIT FACT. H *
CUST. UNIT FACT. H * FULL CALIB. HEIGHT UNIT * H H
100% POINT
* FULL PRESSURE CUSTOMER UNIT H *
ZERO POSITION ADJUSTED DENSITY * CUST. UNIT FACT. H *
100% POINT *
SET LRV
ZERO POSITION
SET URV
DAMPING VALUE DAMPING VALUE
* There are parameters that are only displayed if other parameters are
appropriately configured.
For example the CUST. UNIT FACT. H parameter is only displayed
if the "User unit" option was selected for the HEIGHT UNIT parameter.
Endress+Hauser 69
EXTENDED SETUP LINEARISATION LINEARISATION

Level measuring Level measuring
mode only mode only
Display via on-site Display via ToF Tool,

display only FieldCare or
HART handheld terminal
only
Pressure Level
TEMP. ENG UNIT TEMP. ENG UNIT TANK CONTENT MIN TANK CONTENT MIN
ADJUST DENSITIY TANK CONTENT MAX TANK CONTENT MAX
PROCESS DENSITY TABLE SELECTION TABLE SELECTION
SET LRV * Editor Table

Measuring EDITOR TABLE
Table
SET URV * LIN. EDIT MODE MEASURING TABLE LINE-NUMB
EDITOR TABLE X-VAL.
Y-VAL.
TANK DESCRIPTION
ACTIVE LIN. TAB. X
ACTIVE LIN. TAB Y
TANK DESCRIPTION
TAB. ACTIVE
70 Endress+Hauser
SAFETY CONFIRM. DISPLAY OUTPUT TRANSMITTER INFO
HART DATA TRANSMITTER DATA PROCESS CONNECTION SENSOR DATA
SAFETY LOCK MENU DESCRIPTOR OUTPUT CURRENT BUS ADDRESS DEVICE SERIAL No Pmax PROC. CONN. SENSOR SER. NO.
SAFETY PASSWORD MAIN DATA FORMAT CURR CHARACT. DEVICE TYPE ELECTR. SERIAL No PROC. CONN. TYPE PRESS. SENS LOLIM
DIGIT SETS ALTERNATE DATA OUTPUT FAIL MODE DEVICE REVISION CUST. TAG NUMBER MAT. PROC. CONN. + PRESS. SENS HILIM
2)
CURRENT OUTPUT LANGUAGE ALT. CURR. OUTPUT PREAMBLE NUMBER LONG TAG NUMBER MAT. PROC. CONN. – MINIMUM SPAN
ACK. ALARM MODE DISPLAY CONTRAST SET MAX. ALARM MANUFACTOR ID ADDITIONAL INFO. SEAL TYPE SENSOR MEAS. TYPE
2)
CALIB. OFFSET DIGIT SETS SET MIN. CURRENT HART MESSAGE DEVICE DESIGN. BOLTS MATERIAL Pmin SENS. DAMAGE
3) 2)
MEASURING MODE ASSIGN CURRENT HART DATE HARDWARE REV. NUTS MATERIAL Pmax SENS. DAMAGE
2) 2)
SET LRV PRIMARY VALUE IS SOFTWARE VERSION DRAIN VENT MAT. MAT. MEMBRANE
2) 2)
SET URV PRIMARY VALUE CONFIG RECORDER DRAIN VENT POS. FILLING FLUID
2) 2)
DAMPING VALUE SECONDARY VAL. IS PCB TEMPERATURE THREAD Tmin SENSOR
2) 2)
CONF. PASSWORD SECONDARY VALUE ALLOWED MIN. TEMP MOUNTING THREAD Tmax SENSOR
2) 2)
THIRD VALUE IS ALLOWED MAX. TEMP REMOTE SEAL POS. SENSOR H/WARE REV.
2) 2)
THIRD VALUE DIP STATUS REMOTE SEAL NEG.
2) 2)
4TH VALUE IS DIAPHRAGM SEAL POS.
2) 2)
4 TH VALUE DIAPHRAGM SEAL NEG.
2)
NR OF REMOTE SEAL
2)
FILL FLUID
2) Display via ToF Tool, FieldCare and

3) Level measuring mode only
Endress+Hauser 71
PROCESS INFO OPERATION DIAGNOSTICS
PROCESS VALUE PEAK HOLD INDICATOR SIMULATION MESSAGES USER LIMITS
Pressure Level
MEASURED VALUE MEASURED VALUE COUNTER:P > Pmax ENTER RESET CODE SIMULATION MODE ALARM STATUS Pmin ALARM WINDOW
PRESSURE PRESSURE MAX. MEAS. PRESS. OPERATING HOURS I LAST DIAG. CODE Pmax ALARM WINDOW
CORRECTED PRESS. CORRECTED PRESS. COUNTER:P < Pmin INSERT PIN NO ACK. ALARM MODE Tmin ALARM WINDOW
J
SENSOR PRESSURE SENSOR PRESSURE MIN. MEAS. PRESS. HistoROM AVAIL. ACK. ALARM * Tmax ALARM WINDOW
SENSOR TEMP. SENSOR TEMP. COUNTER:T > Tmax HistoROM CONTROL * RESET ALL ALARMS
Display via ToF Tool,

MEAS. VAL. TREND MEAS. VAL. TREND MAX. MEAS. TEMP. ERROR NO. FieldCare or
HART handheld
LEVEL BEFORE LIN * COUNTER:T< Tmin SELECT ALARMTYPE
terminal only
TANK CONTENTS * MIN. MEAS. TEMP. ALARM DELAY
PCB COUNT:T > Tmax ALARM DISPL. TIME
PCB MAX. TEMP.
PCB COUNT: T< Tmin
PCB MIN. TEMP.
RESET PEAKHOLDS
none Pressure Level Tank content Current Alarm Warning

SIM. PRESSURE SIM. LEVEL SIM. TANK CONT. SIM. CURRENT SIM. ERROR NO.
J J J J J J
72 Endress+Hauser
10.2 Operating matrix HART Commuwin II

! Note!
All parameters are displayed via the ToF Tool, the HART handheld terminal and the on-site display
(→ see section 10.1). Commuwin II only displays the parameters listed below.
H0 H1 H2 H3 H4 H5 H6 H7 H8 H9
V0 Measured Set LRV Set URV Get LRV Get URV Calib. Pos. zero Damping Output fail Press. eng.
Basic value offset adjust value mode unit
setup
V1 Min. meas. Max. meas. Pos. input Sensor Min. meas. Max. PCB PCB min. PCB max. Temp. eng.
Peak hold press. pressure value temp. temp. meas. temp. tempera- temp. temp. unit
indic. ture
V2 Counter: Counter: Safety Counter: Counter: Reset HistoROM HistoROM Table

Transmit- P < Pmin P > Pmax lockstate T < Tmin T > Tmax peakhold avail. control selection
ter info
V3 Measuring Level Measurand Tank Editor Lin. edit Tab. Line-numb X-Val. Y-Val.
Lineari- mode mode content unit table mode activate
sation
V4 Eng. unit Level min./ Level max./ Tank Tank Calibration Empty Empty Full calib. Full
Level level Hydr. press. Hydr. press. content content mode calib. pressure pressure
min. max. min. max.
V5 Unit flow Flow- Max. Max Low flow Set l. fl. cut- Reset Neg. flow Totalizer 1 Totalizer 1
Flow meas. pressure flow cut-off off totalizer 1 tot. 1 unit
type flow
V6 Pmin Alarm Pmax Tmin Tmax Proc. conn. Mat. proc. Mat. proc. Seal type Filling fluid Sensor
Process window Alarm Alarm alarm type conn. + conn. – meas. type
info window window window
V7 Output Set min. Set max. Linear/ Assing Low sensor High sensor Press. sens. Press. sens. Sensor
Output current current alarm sqroot. current trim trim LOLIM HILIM pressure
V8 Simulation Simulated Main line Menu Density Adjust Zero 100% DIP status Damp
Additional mode value format descriptor unit density position point switch
function
V9 Alarm Last diag. Ack. alarm Ack. alarm Alarm Alarm displ. Operating Revision Enter reset Insert PIN
Service status code mode delay time hours count code no
VA Cust. tag Additional Device Sensor ser. Electr. Device Software Cust. unit Flow unit
User number info. serial no no. serial no design. version flow scale
info
10.3 Patents
This product may be protected by at least one of the following patents. Further patents are pending.
• US 5,836,063 A1 i EP 0 797 084 B1
• US 5,877,424 A1 i EP 0 780 674 B1
• DE 203 05 869 U1
• US 6,363,790 A1 i EP 0 995 979 B1
• US 5,670,063 A1 i EP 0 516 579 B1
• US 5,539,611 A1
• US 5,050,034 A1 i EP 0 445 382 B1
• US 5,005,421 A1 i EP 0 351 701 B1
• EP 0 414 871 B1
• EP 1 061 351 B1
• US 5,334,344 A1 i EP 0 490 807 B1
• US 6,703,943 A1
Endress+Hauser 73
Cerabar S PMC71, PMP71/72/75 with 4...20 mA HART Index
Index
Numerics O
4...20 mA test signal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 On-site display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Operating elements, function . . . . . . . . . . . . . . . . . . . 23, 25
A Operating elements, position. . . . . . . . . . . . . . . . . . . . . . . 22
Alarm messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Operating keys, on-site, function. . . . . . . . . . . . . . . . . 23, 25
Operating keys, on-site, Level measuring mode . . . . . . . . . 27
C Operating keys, on-site, Pressure measuring mode. . . . . . . 26
Cable specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Operating keys, position . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Commubox FXA 191, connection. . . . . . . . . . . . . . . . . . . 20 Operating menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28, 67
Overvoltage protection . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
D
Diaphragm seals, installation instructions . . . . . . . . . . . . . 11 P
Diaphragm seals, vacuum application . . . . . . . . . . . . . . . . 11 Pipe mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Position adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Potential matching . . . . . . . . . . . . . . . . . . . . . . . . . . . 18, 20
E Pressure measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Pressure measurement, Quick Setup menu . . . . . . . . . . . . 41
Error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Q
F Quick Setup menu level . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Factory setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Quick Setup menu pressure . . . . . . . . . . . . . . . . . . . . . . . 41
FieldCare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
R
H Repair. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
HART handheld terminal, connection . . . . . . . . . . . . . . . . 19 Repair of Ex-certified devices . . . . . . . . . . . . . . . . . . . . . . 55
Hazardous areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Heat insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Rotating the housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
HistoROM/M-DAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
S
I Scope of delivery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Incoming acceptance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Screening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Installation instructions for devices with diaphragm seals. . 11 SIL 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation instructions for devices without diaphragm seals 8 Software history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
L
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Language, selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Level measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Level measurement, Quick Setup menu . . . . . . . . . . . . . . 44 T
Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Temperature separator, installation instructions . . . . . . . . . 12
Locking operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 ToF Tool operating program . . . . . . . . . . . . . . . . . . . . . . . 34
Trouble-shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
M
Measuring arrangement for level measurement . . . . . . . . . 10 U
Measuring arrangement for pressure measurement . . . . 9–10 Unlocking operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Measuring mode, selection . . . . . . . . . . . . . . . . . . . . . . . . 39
W
N Wall mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Nameplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Welding recommendation. . . . . . . . . . . . . . . . . . . . . . . . . 14
74 Endress+Hauser
Declaration of Hazardous Material and De-Contamination
Erklärung zur Kontamination und Reinigung
Please reference the Return Authorization Number (RA#), obtained from Endress+Hauser, on all paperwork and mark the RA#
clearly on the outside of the box. If this procedure is not followed, it may result in the refusal of the package at our facility.
RA No. Bitte geben Sie die von E+H mitgeteilte Rücklieferungsnummer (RA#) auf allen Lieferpapieren an und vermerken Sie diese
auch außen auf der Verpackung. Nichtbeachtung dieser Anweisung führt zur Ablehnung ihrer Lieferung.
Because of legal regulations and for the safety of our employees and operating equipment, we need the "Declaration of Hazardous Material
and De-Contamination", with your signature, before your order can be handled. Please make absolutely sure to attach it to the outside of the
packaging.
Aufgrund der gesetzlichen Vorschriften und zum Schutz unserer Mitarbeiter und Betriebseinrichtungen, benötigen wir die unterschriebene
"Erklärung zur Kontamination und Reinigung", bevor Ihr Auftrag bearbeitet werden kann. Bringen Sie diese unbedingt außen an der
Verpackung an.
Type of instrument / sensor Serial number

Geräte-/Sensortyp ____________________________________________ Seriennummer ________________________
Used as SIL device in a Safety Instrumented System / Einsatz als SIL Gerät in Schutzeinrichtungen
Process data/Prozessdaten Temperature / Temperatur _________ [°C] Pressure / Druck __________ [ Pa ]

Conductivity / Leitfähigkeit _________ [ S ] Viscosity / Viskosität __________ [mm2/s]
Medium and warnings

Warnhinweise zum Medium
harmful/
Medium /concentration Identification flammable toxic corrosive irritant other * harmless
Medium /Konzentration CAS No. entzündlich giftig ätzend gesundheits- sonstiges* unbedenklich
schädlich/
reizend
Process
medium
Medium im
Prozess
Medium for
process cleaning
Medium zur
Prozessreinigung
Returned part
cleaned with
Medium zur
Endreinigung
* explosive; oxidising; dangerous for the environment; biological risk; radioactive
* explosiv; brandfördernd; umweltgefährlich; biogefährlich; radioaktiv
Please tick should one of the above be applicable, include safety data sheet and, if necessary, special handling instructions.
Zutreffendes ankreuzen; trifft einer der Warnhinweise zu, Sicherheitsdatenblatt und ggf. spezielle Handhabungsvorschriften beilegen.
Description of failure / Fehlerbeschreibung __________________________________________________________________________

______________________________________________________________________________________________________________
______________________________________________________________________________________________________________
Company data /Angaben zum Absender
Company /Firma ___________________________________ Phone number of contact person /Telefon-Nr. Ansprechpartner:

_________________________________________________ ____________________________________________
Address / Adresse Fax / E-Mail ____________________________________________
_________________________________________________
_________________________________________________ Your order No. / Ihre Auftragsnr. ____________________________
“We hereby certify that this declaration is filled out truthfully and completely to the best of our knowledge.We further certify that the returned
parts have been carefully cleaned. To the best of our knowledge they are free of any residues in dangerous quantities.”
“Wir bestätigen, die vorliegende Erklärung nach unserem besten Wissen wahrheitsgetreu und vollständig ausgefüllt zu haben. Wir bestätigen
weiter, dass die zurückgesandten Teile sorgfältig gereinigt wurden und nach unserem besten Wissen frei von Rückständen in gefahrbringen-
der Menge sind.”
P/SF/Konta XII
(place, date / Ort, Datum) Name, dept./Abt. (please print /bitte Druckschrift) Signature / Unterschrift
www.endress.com/worldwide
BA271P/00/en/11.05
71009589
CCS/FM+SGML6.0 71009589

E&H Transmitter

Uploaded by

Copyright:

Available Formats

E&H Transmitter

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

E&H Transmitter

Uploaded by

Copyright:

Available Formats

Operating Instructions

Cerabar S PMC71, PMP71/72/75

Device Documentation Content Remarks

Operating Instructions BA271P – Identification – The documentation is supplied with the

1.1 Designated use

1.2 Installation, commissioning and operation

1.3 Operational safety

1.3.1 Hazardous areas (optional)

1.3.2 Functional Safety SIL 2 (optional)

1.4 Notes on safety conventions and icons

Explosion hazardous area

- Symbol used in drawings to indicate explosion hazardous areas.

Safe area (non-explosion hazardous area)

. Symbol used in drawings to indicate, if necessary, non-explosion hazardous areas.

2.1 Device designation

Fig. 1: Nameplate for Cerabar S

Fig. 2: Additional nameplate for devices for hazardous areas

2.2 Scope of delivery

2.3 CE mark, declaration of conformity

2.4 Registered trademarks

KALREZ, VITON, TEFLON

3.1 Incoming acceptance and storage

3.1.1 Incoming acceptance

3.2 Installation conditions

3.3 Installation instructions

3.3.1 Installation instructions for devices without diaphragm seals –

Pressure measurement in gases

Fig. 3: Measuring arrangement for pressure measurement in gases

Pressure measurement in steams

Fig. 4: Measuring arrangement for pressure measurement in steams

• Mount Cerabar S with siphon below the tapping point.

Pressure measurement in liquids

Fig. 5: Measuring arrangement for pressure measurement in liquids

Fig. 6: Measuring arrangement for level

• Mount Cerabar S below the lowest measuring point.

3.3.2 Installation instructions for devices with diaphragm seals –

Mounting with temperature separator

3.3.3 Seal for flange mounting

Fig. 9: Mounting the versions with flange or diaphragm seal

3.3.4 Heat insulation – PMC71 high temperature version and PMP75

PMC71 high temperature version PMP75

Ambient temperature (TA) ≤ 70°C (158°F) ≤ 70°C (158°F)

3.3.5 Wall and pipe-mounting (optional)

Please note the following when mounting:

3.3.6 PMP71, version prepared for diaphragm seal mount –

Fig. 11: Version U1: prepared for diaphragm seal mount

Consecutive Sketch/welding groove Base material Welding Welding Inert gas,

A1 Adapter made of 141 PB Inert gas

3.3.7 Rotating the housing

Fig. 12: Aligning the housing

3.4 Post-installation check

4.1 Connecting the device

➁ 4... 20mA Test

Fig. 13: Electrical connection 4...20 mA HART

4.1.1 Connecting devices with Harting plug Han7D

4.1.2 Connection devices with M12 plug

4.1.3 Connection devices with 7/8" plug

4.2 Connecting the measuring unit

4.2.1 Supply voltage