HA17555 Series

Precision Timer

ADE-204-064 (Z)
Rev. 0
Dec. 2000

Description

HA17555 Series are ICs designed for accurate time delays or oscillations. It provides both of trigger
terminal and reset terminal in order to enable a wide scope of application including Mono Multi Vibrator
and Astable Multi Vibrator, and the number of external components is fewer. Further, it’s compatible with
NE555 of singnetics.

Features

• Mono multi vibrator can be constructed with one resistor and one capacitor.
• Astable multi vibrator can be constructed with two resistors and one capacitor.
• Delay time can be established widely from several µ seconds to several hours.
• Pulse Duty can be controlled.
• The maximum value of both sink current and source current is 200mA.
• Direct connection of output to TTL is possible.
• Temperature/delay time ratio is 50 ppm/°C (typ).
• Output is normally in the on and off states.

Ordering Information
Application Type No. Package
Industrial use HA17555PS DP-8
HA17555FP FP-8D
Commercial use HA17555 DP-8
HA17555F FP-8D
HA17555 Series

Applications

• Delay Time Generator (Mono Multi Vibrator)

• Pulse Generator (Astable Multi Vibrator)
• Pulse Width Modulator
• Pulse Location Modulator
• Miss Pulse Detector

Pin Arrangement

GND 1 8 VCC

Trigger 2 7 Discharge

Output 3 6 Threshold

Reset 4 5 Control Voltage

(Top View)

Pin Description
Pin No. Function
1 Ground pin
2 Trigger pin
3 Output pin
4 Reset pin
5 Control voltage pin
6 Threshold pin
7 Discharge pin
8 VCC pin

2
 HA17555 Series
Circuit Schematic

Control
Voltage

VCC
R1 R2 R3 R4 R12
Q21
Q5 Q6 Q7 Q8 Q9 Q19 Q22
R7 R13

Q23
Threshold Q1 Q4 Q20 Output
Q2 Q3
Q18 R14
R8 Q24
R16
R11
Q11 Q12 R15 Discharge
Trigger Q10 Q13 Q16 Q17 Q14

R5
R6 Q15
R9
GND

Reset Q25

Block Diagram

VCC

Threshold
R
Control

S Q Output
Trigger CLR
Discharge

Reset

3
HA17555 Series

Absolute Maximum Ratings (Ta = 25°C)

Item Symbol HA17555PS/FP HA17555/F Unit
Supply voltage VCC 18 18 V
Discharge current IT 200 200 mA
Output source current Isource 200 200 mA
Output sink current Isink 200 200 mA
1
Power dissipation* PT 600/385 600/385 mW
Operating temperature Topr –20 to +75 –20 to +70 °C
Storage temperature Tstg –55 to +125 –55 to +125 °C
Note: 1. For the HA17555/PS,
This value applies up to Ta = 50°C; at temperatures above this, 8.3mW/°C derating should be
applied.
For the HA17555F/FP,
This value applies up to Ta = 25°C; at temperatures above this, 3.85mW/°C derating should be
applied.
See notes on SOP Package Usage in Reliability section.

4
 HA17555 Series
a. HA17555PS

Maximum Power Dissipation PTmax (W)

b. HA17555FP
0.7
a. 0.6 W
0.6 8.3 mW/°C

0.5
3.85 mW/°C
0.4 b. 0.385 W

0.3

0.2

0.1

–40 –20 0 20 40 60 70 80 100 120

Ambient Temperature Ta (°C)

a. HA17555
Maximum Power Dissipation PTmax (W)

b. HA17555F
0.7
a. 0.6 W
0.6 8.3 mW/°C

0.5
3.85 mW/°C
0.4 b. 0.385 W

0.3

0.2

0.1

–40 –20 0 20 40 60 70 80 100 120

Ambient Temperature Ta (°C)

5
HA17555 Series

Electrical Characteristics (VCC = 5 to 15 V, Ta = 25°C)

Item Symbol Min Typ Max Unit Test conditions
1
Supply voltage* VCC 4.5 — 16.0 V
Supply current I CC — 3.0 6.0 mA VCC = 5 V, RL = ∞
I CC — 10 15 mA VCC = 15 V, RL = ∞
2
Timing error* Et — 1.0 — %
(Inherent error)
Timing error*2 Et — 50 — ppm/°C Ta = –20 to + 75°C
(Ta dependency)
Timing error*2 Et — 0.01 — %/V VCC = 5 to 15 V
(Voltage dependency)
Threshold voltage Vth — 2/3 — V × VCC
Trigger voltage VT — 5.0 — V VCC = 15 V
VT — 1.67 — V VCC = 5 V
Trigger current IT — 0.5 — µA
Reset voltage VR 0.2 0.5 1.0 V
Reset current IR — 0.1 — mA
Threshold current Ith* 3
— 0.1 0.25 µA
Control voltage VCL 9 10 11 V VCC = 15 V
VCL 2.6 3.33 4.0 V VCC = 5 V
Output voltage VOL — 0.1 0.25 V VCC = 15 V, Isink = 10 mA
— 0.4 0.75 V VCC = 15 V, Isink = 50 mA
— 2.0 2.5 V VCC = 15 V, Isink = 100 mA
— 2.5 — V VCC = 15 V, Isink = 200 mA
— 0.25 0.35 V VCC = 5 V, Isink = 5 mA
Output voltage VOH — 12.5 — V VCC = 15 V, Isource = 200 mA
12.75 13.3 — V VCC = 15 V, Isource = 100 mA
2.75 3.3 — V VCC = 5 V, Isource = 100 mA
Output rise time tr — 100 — ns No loading
Output fall time tf — 100 — ns No loading
4
Oscillation pulse width* tw 10.0 — — ns
Notes: 1. When output is low (When it is high, ICC is lower by 1 mA typically.)
2. RA, RB = 1 k to 100 kΩ, C = 0.1 µF, V CC = 5 V or 15 V.
3. (RA + RB) at VCC = 15 V is determined by the value of Ith. It is 20 MΩ Max.
4. Output pulse width at mono multi circuit. Output high level pulse width at astable circuit.

6
 HA17555 Series
Characteristic Curves

Quiescent Current vs. Supply Voltage

12.0 Supply Voltage (VCC) Output Voltage (VOH)
Vout : Low Level vs. Source Current
2.0

Supply Voltage VCC Output Voltage VOH (V)

10.0 Ta = –20°C
Quiescent Current ICC (mA)

Ta = –20°C
1.6
8.0
25°C
25°C
1.2
6.0
75°C
75°C
0.8
4.0

5 V < VCC < 15 V

2.0 0.4

0 0
5.0 10.0 15.0 1 3 10 30 100
Supply Voltage VCC (V) Source Current Isource (mA)

Output Voltage (VOL) vs. Sink Current (1) Output Voltage (VOL) vs. Sink Current (2)
10 10
Ta = 75°C VCC = 10 V
25°C
Output Voltage VOL (V)

3 –20°C 3
Output Voltage VOL (V)

1.0 1.0

0.3 0.3 Ta = 75°C

–20°C
0.1 0.1

VCC = 5 V 25°C
0.03 0.03

0.01 0.01
1 3 10 30 100 300 1,000 1 3 10 30 100 300 1,000
Sink Current Isink (mA) Sink Current Isink (mA)

Output Voltage (VOL) vs. Sink Current (3) Relative Delay Time vs. Supply Voltage
10 1.015
VCC = 15 V
3 1.010
Output Voltage VOL (V)

Relative Delay Time

1.0 1.005

Ta = –75°C 1.000
0.3

0.1 –20°C 0.995

25°C
0.03 0.990

0.01 0.985
1 3 10 30 100 300 1,000 3 5 10 15 18
Sink Current Isink (mA) Supply Voltage VCC (V)

7
HA17555 Series

Relative Delay Time Minimum Trigger Pulse Width

vs. Ambient Temperature vs. Low Level Trigger Voltage
1.015 200

Minimum Trigger Pulse Width (ns)

1.010
150
Relative Delay Time

1.005

1.000 100
Ta = –20°C
0.995
50 25°C
0.990
75°C

0.985
–20 0 20 40 60 80 0 0.1 0.2 0.3 0.4
Ambient Temperature Ta (°C) Low Level Trigger Voltage (×VCC)

Propagation Delay Time

vs. Low Level Trigger Voltage
300
Propagation Delay Time (ns)

200 Ta = –20°C

25°C
100
75°C

0 0.1 0.2 0.3 0.4

Low Level Trigger Voltage (×VCC)

8
 HA17555 Series

Package Dimensions

Unit: mm

9.6
10.6 Max
8 5

7.4 Max
6.3
1 4
0.89 1.3

1.27 Max 2.54 Min 5.06 Max 7.62

0.1 Min

+ 0.10
0.25 – 0.05

2.54 ± 0.25 0.48 ± 0.10 0° – 15°

Hitachi Code DP-8

JEDEC Conforms
EIAJ Conforms
Mass (reference value) 0.54 g

Unit: mm

4.85
5.25 Max
8 5
4.4

1 4
*0.22 ± 0.05
0.20 ± 0.04
2.03 Max

6.50 +– 0.15
0.25
0.75 Max
1.05

0° – 8°
0.10 ± 0.10

1.27 0.60 +– 0.18

0.25

*0.42 ± 0.08
0.40 ± 0.06
0.15

0.12 M
Hitachi Code FP-8D
JEDEC —
*Dimension including the plating thickness EIAJ Conforms
Base material dimension Mass (reference value) 0.10 g

9
HA17555 Series

Cautions

1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’s patent,
copyright, trademark, or other intellectual property rights for information contained in this document.
Hitachi bears no responsibility for problems that may arise with third party’s rights, including
intellectual property rights, in connection with use of the information contained in this document.
2. Products and product specifications may be subject to change without notice. Confirm that you have
received the latest product standards or specifications before final design, purchase or use.
3. Hitachi makes every attempt to ensure that its products are of high quality and reliability. However,
contact Hitachi’s sales office before using the product in an application that demands especially high
quality and reliability or where its failure or malfunction may directly threaten human life or cause risk
of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation,
traffic, safety equipment or medical equipment for life support.
4. Design your application so that the product is used within the ranges guaranteed by Hitachi particularly
for maximum rating, operating supply voltage range, heat radiation characteristics, installation
conditions and other characteristics. Hitachi bears no responsibility for failure or damage when used
beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable
failure rates or failure modes in semiconductor devices and employ systemic measures such as fail-
safes, so that the equipment incorporating Hitachi product does not cause bodily injury, fire or other
consequential damage due to operation of the Hitachi product.
5. This product is not designed to be radiation resistant.
6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without
written approval from Hitachi.
7. Contact Hitachi’s sales office for any questions regarding this document or Hitachi semiconductor
products.

Hitachi, Ltd.
Semiconductor & Integrated Circuits.
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
Tel: Tokyo (03) 3270-2111 Fax: (03) 3270-5109
URL NorthAmerica : http://semiconductor.hitachi.com/
Europe : http://www.hitachi-eu.com/hel/ecg
Asia : http://sicapac.hitachi-asia.com
Japan : http://www.hitachi.co.jp/Sicd/indx.htm
For further information write to:
Hitachi Semiconductor Hitachi Europe GmbH Hitachi Asia Ltd. Hitachi Asia (Hong Kong) Ltd.
(America) Inc. Electronic Components Group Hitachi Tower Group III (Electronic Components)
179 East Tasman Drive, Dornacher Straβe 3 16 Collyer Quay #20-00, 7/F., North Tower,
San Jose,CA 95134 D-85622 Feldkirchen, Munich Singapore 049318 World Finance Centre,
Tel: <1> (408) 433-1990 Germany Tel : <65>-538-6533/538-8577 Harbour City, Canton Road
Fax: <1>(408) 433-0223 Tel: <49> (89) 9 9180-0 Fax : <65>-538-6933/538-3877 Tsim Sha Tsui, Kowloon,
Fax: <49> (89) 9 29 30 00 URL : http://www.hitachi.com.sg Hong Kong
Hitachi Europe Ltd. Tel : <852>-(2)-735-9218
Hitachi Asia Ltd.
Fax : <852>-(2)-730-0281
Electronic Components Group. (Taipei Branch Office)
Whitebrook Park URL : http://www.hitachi.com.hk
4/F, No. 167, Tun Hwa North Road,
Lower Cookham Road Hung-Kuo Building,
Maidenhead Taipei (105), Taiwan
Berkshire SL6 8YA, United Kingdom Tel : <886>-(2)-2718-3666
Tel: <44> (1628) 585000 Fax : <886>-(2)-2718-8180
Fax: <44> (1628) 585160 Telex : 23222 HAS-TP
URL : http://www.hitachi.com.tw
Copyright  Hitachi, Ltd., 2000. All rights reserved. Printed in Japan.
Colophon 2.0

10