Datasheet
Datasheet
Datasheet
MXP-243S
Applications:
1.25Gb/s 1000Base-LX Ethernet
1.0625Gb/s Fiber Channel
Features: Description
Operating bit rate MXP-243S SFP transceiver is an excellent product , which is a series of
1.25Gb/s high performance optical modules suitable for the Fiber optic communication
Operating at and Ethernet accessing for signal that rates up to 1.25Gb/s.
1280-1330nm wavelength The transmitter section of MXP-243S SFP incorporates 1310nm FP laser as
Single +3.3V power the optical source. And the receiver section consists of a PIN photodiode mounted
supply together with a trans-impedance preamplifier (TIA).
Differential LVPECL Because of its hot-pluggable capability , MXP-243S SFP transceiver can
inputs and outputs be installed in or removed from any MSA compliant pluggable small form
TTL signal detect factor port regardless of whether the host equipment is operating or not.
indicator Furthermore , MXP-243S SFP transceiver features an E/EPROM that
Industry standard contains the detailed product’s information stored for retrieval by host
small form pluggable equipment. For further information, please refer to SFP Multi-Source
(SFP) package Agreement (MSA).
Hot-pluggable The transceiver operates at up to1.25G data-rate from a single +3.3 V
capability power supply only. And it uses TTL signal as detect indicator.
Duplex LC connector
Metal enclosure, for Specification:
lower EMI
Very low jitter Operating Information
Low power Part Number Input/Output Signal Detect Voltage Temperature
dissipation MXP-243S AC/AC TTL +3.3V 0℃ to70℃
Link length up to
20km in 9/125 SMF
1of7
Transmitter Optical, Electrical Characteristics
Parameter Symbol Min Typ Max Unit Note
Input differential impedance Rin 100 Ω
Differential data input swing Vin PP 100 1200 mV
Transmit Disable Input High Voltage 2.0 V
Transmit Disable Input Low Voltage 0.8 V
Transmit Fault OutputHighVoltage 2.0 V
Transmit Fault Output LowVoltage 0.8 V
Transmit Disable Assert Time 0.14 5 µs
Optical Transmit Power PO -9.5 -3 dBm Average Power
Extinction Ratio ER 9 dB
Output Spectrum Width(RMS) ∆λ 4 nm
2of7
Pin View:
20 VEET 1 VEET
19 TD- 2 TX Fault
18 TD+ 3 TX Disable
17 VEET 4 MOD_DEF(2)
16 VCCT 5 MOD_DEF(1)
15 VCCR 6 MOD_DEF(0)
13 RD+ 8 LOS
12 RD- 9 VEER
11 VEER 10 VEER
Pin Assignment:
3of7
Block Diagram Of Transceiver
Transmitter Section
The transmitter section RECEIVER
VCC
consists of 1310nm FP
LIMITING AMP
DATA+
RXLOS
RXd-
laser in an eye safe optical DATA-
PT
RXd+
ID E PROM
MOD_DEF(1)
TRANSMITTER
2
MOD_DEF(0)
The laser OSA is driven by BIAS
VCC
a LD driver IC which TXd+
DATA+
DRIVER
TXd-
DATA-
converts differential input TX-DIS
LD
PM
TX-FAULT
LVPECL logic signals into
LD
an analog laser driving
current.
TX-FAULT
TX Fault is an open collector/drain output, which should be pulled up with a 4.7K –
10KΩ resistor on the host board. Pull up voltage between 2.0V and VccT, R+0.3V. When
high, output indicates a laser fault of some kind. Low indicates normal operation. In the
low state, the output will be pulled to < 0.8V.
When sensing an improper power level in the laser driver, the SFP sets this signal
high and turns off the laser. TX-FAULT can be reset with the TX-DISABLE line. The
signal is in TTL level.
TX-DISABLE
TX disable is an input that is used to shut down the transmitter optical output. It is
pulled up within the module with a 4.7 – 10 KΩ resistor. Its states are: Low (0 – 0.8V):
Transmitter on; (>0.8, < 2.0V): Undefined; High (2.0 – 3.465V): Transmitter Disabled;
Open: Transmitter Disabled. The TX-DISABLE signal is high (TTL logic “1”) to turn off
the laser output. The laser will turn on when TX-DISABLE is low (TTL logic “0”).
TD-/+
These are the differential transmitter inputs. They are AC-coupled, differential lines
with 100Ω differential termination inside the module. The AC coupling is done inside the
module and is thus not required on the host board. The inputs will accept differential
swings of 500 – 2400 mV (250 – 1200 mV single-ended), though it is recommended that
values between 500 and 1200 mV differential (250 – 600 mV single-ended) be used for
best EMI performance.
4of7
Receiver Section
The receiver utilizes an InGaAs PIN photodiode mounted together with a
trans-impedance preamplifier IC in an OSA. This OSA is connected to a circuit providing
post-amplification quantization, and optical signal detection.
RX-LOS
LOS (Loss of Signal) is an open collector/drain output, which should be pulled up
with a 4.7K – 10KΩresistor. Pull up voltage between 2.0V and VccT, R+0.3V. When high,
this output indicates the received optical power is below the worst-case receiver sensitivity
(as defined by the standard in use). Low indicates normal operation. In the low state, the
output will be pulled to < 0.8V.
The RX-LOS is high (TTL logic “1”) when there is no incoming light from the
companion transceiver. This signal is normally used by the system for the diagnostic
purpose. The signal is operated in TTL level.
RD-/+
These are the differential receiver outputs. They are AC coupled 100Ω differential
lines which should be terminated with 100 Ω(differential) at the user SERDES. The AC
coupling is done inside the module and is thus not required on the host board. The voltage
swing on these lines will be between 370 and 2000 mV differential (185 – 1000 mV single
ended) when properly terminated.
DC+3.3V DC+3.3V
4.7K to 10KΩ 4.7K to 10KΩ
TX-DISABLE
DC+3.3V TX-FAULT
2X150Ω
DC+3.3V Z0=50Ω
SerDat IN- RX-DATQ
DC+3.3V
4.7K to 10KΩ RX-LOS
DC +3.3V
3X4.7K to 10KΩ MOD-DEF(2)
MOD-DEF(1) EEPROM
MOD-DEF(0)
RGND
5of7
Dimensions
Dimensions are in millimeters. All dimensions are ±0.1mm unless otherwise specified. (unit:mm).
S
N
:
0
0
0
0
0
2
0
0
11
54.5
M
X
P
-
2
3
S
4
T
r
a
n
s
c
e
i
v
e
r
6.25
1.5
3.65
1
8.6
3.5
5.5
1.9
8
13.5
15.5
6of7
Statement:
Genuine-optical company has the ultimate explanation authority to the content of the product material, if there have some
modifies, we’re sorry for can’t give a notice.
Users should for our company on their one's own uses performance should having prove going on of products, our
company is not responsible for performance of user's products . Any standard , agreement that this text quotes are only for
referential use, do not do the basis of examining the quality of the products , whether the products are qualified to produce
Version: V2.1
Contact Information:
Address: Huagong Tech BDG, Science &Technology Region of Hust,
Tel: +86-27-87180097
Website: http://www.genuine-opto.com
7of7