TS-SF-1315-02

155Mb/s 1310nm Single-mode SFP Transceiver

PRODUCT FEATURES

 Up to 155Mb/s data links

 FP laser transmitter and PIN photo-detector.

 Up to 2km on 9/125µm SMF

 Hot-pluggable SFP footprint

 Duplex LC/UPC type pluggable optical interface

 Low power dissipation

 Metal enclosure, for lower EMI

 RoHS compliant and lead-free

 Single +3.3V power supply

 Compliant with SFF-8472

 Case operating temperature

Commercial: 0°C to +70°C

Extended: -10°C to +80°C

Industrial: -40°C to +85°C

APPLICATIONS

 Switch to Switch Interface

 Fast Ethernet

 Switched Backplane Applications

1
SHENZHEN TRANSCOM TECHNOLOGY LIMITED / Web: www.sz-transcom.com / Tel: +86 755 88278677 / Fax: +86 755 26029402
 Router/Server Interface

 Other Optical Links

PRODUCT DESCRIPTION

TRANSCOM’s TS-SF-1315-02 Small Form Factor Pluggable (SFP) transceivers are compatible with the Small
Form Factor Pluggable Multi-Sourcing Agreement (MSA). The transceiver consists of four sections: the LD driver,
the limiting amplifier, the 1310nm FP laser and the PIN photo-detector. The module data links up to 2KM in 9/125
um single mode fiber.

The optical output can be disabled by a TTL logic high-level input of Tx Disable, and the system also can disable
the module via I2C. Tx Fault is provided to indicate that degradation of the laser. Loss of signal (LOS) output is
provided to indicate the loss of an input optical signal of receiver or the link status with partner. The system can
also get the LOS (or Link)/Disable/Fault information via I2C register access.

Ordering information
Data
Product part Wavelength Transmission
Rate Media Temperature Range(Tcase)（℃）
Number (nm) Distance(km)
(Mbps)
Single mode
TS-SF-1315-02 155 1310 2 0~70 commercial
fiber
Single
TS-SF-1315-02E 155 1310 2 -10~80 extended
mode fiber
Single
TS-SF-1315-02A 155 1310 2 -40~85 industrial
mode fiber

I. Pin Descriptions
Pin Symbol Name/Description Ref.
1 VEET Transmitter Ground (Common with Receiver Ground) 1
2 TFAULT Transmitter Fault.
3 TDIS Transmitter Disable. Laser output disabled on high or open. 2
4 MOD_DEF(2) Module Definition 2. Data line for Serial ID. 3
5 MOD_DEF(1) Module Definition 1. Clock line for Serial ID. 3
6 MOD_DEF(0) Module Definition 0. Grounded within the module. 3
7 Rate Select No connection required 4
8 LOS Loss of Signal indication. Logic 0 indicates normal operation. 5
9 VEER Receiver Ground (Common with Transmitter Ground) 1

2
SHENZHEN TRANSCOM TECHNOLOGY LIMITED / Web: www.sz-transcom.com / Tel: +86 755 88278677 / Fax: +86 755 26029402
 10 VEER Receiver Ground (Common with Transmitter Ground) 1
11 VEER Receiver Ground (Common with Transmitter Ground) 1

12 RD- Receiver Inverted DATA out. AC Coupled

13 RD+ Receiver Non-inverted DATA out. AC Coupled
14 VEER Receiver Ground (Common with Transmitter Ground) 1
15 VCCR Receiver Power Supply
16 VCCT Transmitter Power Supply
17 VEET Transmitter Ground (Common with Receiver Ground) 1
18 TD+ Transmitter Non-Inverted DATA in. AC Coupled.
19 TD- Transmitter Inverted DATA in. AC Coupled.
20 VEET Transmitter Ground (Common with Receiver Ground) 1

Notes:
1. Circuit ground is internally isolated from chassis ground.
2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
3. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.6V.MOD_DEF (0)
pulls line low to indicate module is plugged in.
4. This is an optional input used to control the receiver bandwidth for compatibility with multiple data rates (most
likely Fiber Channel 1x and 2x Rates).If implemented, the input will be internally pulled down with > 30kΩ
resistor. The input states are:
 Low (0 – 0.8V): Reduced Bandwidth
 (>0.8, < 2.0V): Undefined
 High (2.0 – 3.465V): Full Bandwidth
 Open: Reduced Bandwidth
5. LOS is open collector output should be pulled up with 4.7k-10k ohms on host board to a voltage between 2.0V
and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.

Figure2. Pin out of Connector Block on Host Board

3
SHENZHEN TRANSCOM TECHNOLOGY LIMITED / Web: www.sz-transcom.com / Tel: +86 755 88278677 / Fax: +86 755 26029402
II. Absolute Maximum Ratings
Parameter Symbol Min. Typ. Max. Unit Note
Storage Temperature Ts -40 85 ºC

Storage Ambient Humidity HA 5 95 %

Power Supply Voltage VCC -0.5 4 V

Signal Input Voltage -0.3 Vcc+0.3 V

Receiver Damage Threshold 5 dBm

III. Recommended Operating Conditions

Parameter Symbol Min. Typ. Max. Unit Note
0 70 TS-SF-1315-02

Case Operating Temperature Tcase -10 80 ºC TS-SF-1315-02E

-40 85 TS-SF-1315-02A

Ambient Humidity HA 5 70 % Non-condensing

Power Supply Voltage VCC 3.13 3.3 3.47 V

Power Supply Current ICC 280 mA

Power Supply Noise Rejection 100 mVp-p 100Hz to 1MHz

Data Rate 155/155 Mbps TX Rate/RX Rate

Transmission Distance 2 KM
Coupled Fiber Single mode fiber 9/125um SMF

IV. Specification of Transmitter

Parameter Symbol Min. Typ. Max. Unit Note
Average Output Power POUT -15 -8 dBm

Extinction Ratio ER 8.2 dB

Center Wavelength λC 1270 1310 1360 nm FP Laser
Spectrum Width (RMS) σ 3.5 nm

Transmitter OFF Output Power POff -45 dBm

Differential Line Input Impedance RIN 90 100 110 Ohm

Total Jitter (Peak-Peak) tJ 1 ns Note (1)

Output Eye Mask Compliant with G.957(class 1 laser safety) Note (2)

4
SHENZHEN TRANSCOM TECHNOLOGY LIMITED / Web: www.sz-transcom.com / Tel: +86 755 88278677 / Fax: +86 755 26029402
Note (1): Measured at 2^23-1 NRZ PRBS pattern.
(2): Transmitter eye mask definition.

V. Specification of Receiver

Parameter Symbol Min. Typ. Max. Unit Note

Input Optical Wavelength λIN 1270 1610 nm
Receiver Sensitivity PIN -24 dBm Note (1)
Input Saturation Power (Overload) PSAT -8 dBm
Los Of Signal Assert PA -25 dBm
Los Of Signal De-assert PD -38 dBm Note (2)
LOS Hysteresis PA-PD 0.5 2 6 dB

Note (1): Measured with Light source 1310nm, ER=8.2dB; BER =<10^-12 @PRBS=2^23-1 NRZ.

Note (2): When LOS de-asserted, the RX data+/- output is High-level (fixed)

VI. Electrical Interface Characteristics

Parameter Symbol Min. Typ. Max. Unit Note
Transmitter
Total Supply Current ICC A mA Note (1)
Transmitter Disable Input-High VDISH 2 Vcc+0.3 V
Transmitter Disable Input-Low VDISL 0 0.8 V
Transmitter Fault Input-High VDISL 2 Vcc+0.3 V
Transmitter Fault Input-Low VTxFH 0 0.8 V
Receiver
Total Supply Current ICC B mA Note (1)
LOSS Output Voltage-High VLOSH 2 Vcc+0.3 V
LVTTL
LOSS Output Voltage-Low VLOSL 0 0.8 V

Note (1) A (TX) + B (RX) = 280mA (Not include termination circuit)

5
SHENZHEN TRANSCOM TECHNOLOGY LIMITED / Web: www.sz-transcom.com / Tel: +86 755 88278677 / Fax: +86 755 26029402
VII. Recommend Circuit Schematic

VIII. Mechanical Specifications (Unit: mm)

6
SHENZHEN TRANSCOM TECHNOLOGY LIMITED / Web: www.sz-transcom.com / Tel: +86 755 88278677 / Fax: +86 755 26029402
 TS-SF-1315-02
IX. Regulatory Compliance
Feature Reference Performance
Compatible with
Electrostatic discharge（ESD） IEC/EN 61000-4-2
standards
Electromagnetic Interference FCC Part 15 Class B EN 55022 Class B Compatible with
(EMI) (CISPR 22A) standards
FDA 21CFR 1040.10, 1040.11 IEC/EN
Laser Eye Safety Class 1 laser product
60825-1，2
Compatible with
Component Recognition IEC/EN 60950 ，UL
standards
Compatible with
ROHS 2002/95/EC
standards
Compatible with
EMC EN61000-3
standards

Appendix A. Document Revision

Version No. Date Description

1.0 2011-04-20 Preliminary datasheet

2.0 2011-09-10 Update format and company’s logo

7
SHENZHEN TRANSCOM TECHNOLOGY LIMITED / Web: www.sz-transcom.com / Tel: +86 755 88278677 / Fax: +86 755 26029402