Types: List of Valves
Types: List of Valves
Types: List of Valves
Valves are quite diverse and may be classified into a number of basic types. Valves may also be
classified by how they are actuated:
Hydraulic
Pneumatic
Manual
Solenoid valve
Motor
Components
The main parts of the most usual type of valve are the body and the bonnet. These two parts
form the casing that holds the fluid going through the valve.
Body
The valve's body is the outer casing of most or all of the valve that contains the internal parts or
trim. The bonnet is the part of the encasing through which the stem (see below) passes and that
forms a guide and seal for the stem. The bonnet typically screws into or is bolted to the valve
body.
Valve bodies are usually metallic or plastic. Brass, bronze, gunmetal, cast iron, steel, alloy steels
and stainless steels are very common.[1] Seawater applications, like desalination plants, often use
duplex valves, as well as super duplex valves, due to their corrosion resistant properties,
particularly against warm seawater. Alloy 20 valves are typically used in sulphuric acid plants,
whilst monel valves are used in hydrofluoric acid (HF Acid) plants. Hastelloy valves are often
used in high temperature applications, such as nuclear plants, whilst inconel valves are often
used in hydrogen applications. Plastic bodies are used for relatively low pressures and
temperatures. PVC, PP, PVDF and glass-reinforced nylon are common plastics used for valve
bodies.[citation needed]
Bonnet
A bonnet acts as a cover on the valve body. It is commonly semi-permanently screwed into the
valve body or bolted onto it. During manufacture of the valve, the internal parts are put into the
body and then the bonnet is attached to hold everything together inside. To access internal parts
of a valve, a user would take off the bonnet, usually for maintenance. Many valves do not have
bonnets; for example, plug valves usually do not have bonnets. Many ball valves do not have
bonnets since the valve body is put together in a different style, such as being screwed together at
the middle of the valve body.
Ports
Ports are passages that allow fluid to pass through the valve. Ports are obstructed by the valve
member or disc to control flow. Valves most commonly have 2 ports, but may have as many as
20. The valve is almost always connected at its ports to pipes or other components. Connection
methods include threadings, compression fittings, glue, cement, flanges, or welding.
Handle or actuator
A handle is used to manually control a valve from outside the valve body. Automatically
controlled valves often do not have handles, but some may have a handle (or something similar)
anyway to manually override automatic control, such as a stop-check valve. An actuator is a
mechanism or device to automatically or remotely control a valve from outside the body. Some
valves have neither handle nor actuator because they automatically control themselves from
inside; for example, check valves and relief valves may have neither.
Disc
Valve disc
A disc or valve member is a movable obstruction inside the stationary body that adjustably
restricts flow through the valve. Although traditionally disc-shaped, discs come in various
shapes. Depending on the type of valve, a disc can move linearly inside a valve, or rotate on the
stem (as in a butterfly valve), or rotate on a hinge or trunnion (as in a check valve). A ball is a
round valve member with one or more paths between ports passing through it. By rotating the
ball, flow can be directed between different ports. Ball valves use spherical rotors with a
cylindrical hole drilled as a fluid passage. Plug valves use cylindrical or conically tapered rotors
called plugs.[ambiguous] Other round shapes for rotors are possible as well in rotor valves, as long as
the rotor can be turned inside the valve body. However, not all round or spherical discs are
rotors; for example, a ball check valve uses the ball to block reverse flow, but is not a rotor
because operating the valve does not involve rotation of the ball.
Seat
The seat is the interior surface of the body which contacts the disc to form a leak-tight seal. In
discs that move linearly or swing on a hinge or trunnion, the disc comes into contact with the
seat only when the valve is shut. In disks that rotate, the seat is always in contact with the disk,
but the area of contact changes as the disc is turned. The seat always remains stationary relative
to the body.
Seats are classified by whether they are cut directly into the body, or if they are made of a
different material:
Hard seats are integral to the valve body. Nearly all hard seated metal valves have a
small amount of leakage.
Soft seats are fitted to the valve body and made of softer materials such as PTFE or
various elastomers such as NBR, EPDM, or FKM depending on the maximum operating
temperature.
The shut off butterfly valve for a Francis turbine at Gordon Power Station, Tasmania
Ball valve
A closed soft seated valve is much less liable to leak when shut while hard seated valves are
more durable. Gate, globe, and check valves are usually hard seated while butterfly, ball, plug,
and diaphragm valves are usually soft seated.
Stem
The stem transmits motion from the handle or controlling device to the disc. The stem typically
passes through the bonnet when present. In some cases, the stem and the disc can be combined in
one piece, or the stem and the handle are combined in one piece.
The motion transmitted by the stem may be a linear force, a rotational torque, or some
combination of these (Angle valve using torque reactor pin and Hub Assembly). The valve and
stem can be threaded such that the stem can be screwed into or out of the valve by turning it in
one direction or the other, thus moving the disc back or forth inside the body.[ambiguous] Packing is
often used between the stem and the bonnet to maintain a seal. Some valves have no external
control and do not need a stem as in most check valves.
Valves whose disc is between the seat and the stem and where the stem moves in a direction into
the valve to shut it are normally-seated or front seated. Valves whose seat is between the disc
and the stem and where the stem moves in a direction out of the valve to shut it are reverse-
seated or back seated. These terms don't apply to valves with no stem or valves using rotors.
Inconel X750 spring
Gaskets
Gaskets are the mechanical seals, or packings, used to prevent the leakage of a gas or fluids from
valves.
Valve balls
A valve ball is also used for severe duty, high-pressure, high-tolerance applications. They are
typically made of stainless steel, titanium, Stellite, Hastelloy, brass, or nickel. They can also be
made of different types of plastic, such as ABS, PVC, PP or PVDF.
Spring
Many valves have a spring for spring-loading, to normally shift the disc into some position by
default but allow control to reposition the disc. Relief valves commonly use a spring to keep the
valve shut, but allow excessive pressure to force the valve open against the spring-loading. Coil
springs are normally used. Typical spring materials include zinc plated steel, stainless steel, and
for high temperature applications Inconel X750.
Trim
The internal elements of a valve are collectively referred to as a valve's trim. According to API
Standards 600, "Steel Gate Valve-Flanged and Butt-welding Ends, Bolted Bonnets", the trim
consists of stem, seating surface in the body, gate seating surface, bushing or a deposited weld
for the backseat and stem hole guide, and small internal parts that normally contact the service
fluid, excluding the pin that is used to make a stem-to-gate connection (this pin shall be made of
an austenitic stainless steel material).
Valve positions are operating conditions determined by the position of the disc or rotor in the
valve. Some valves are made to be operated in a gradual change between two or more positions.
Return valves and non-return valves allow fluid to move in 2 or 1 directions respectively.
Two-port valves
Operating positions for 2-port valves can be either shut (closed) so that no flow at all goes
through, fully open for maximum flow, or sometimes partially open to any degree in between.
Many valves are not designed to precisely control intermediate degree of flow; such valves are
considered to be either open or shut. Some valves are specially designed to regulate varying
amounts of flow. Such valves have been called by various names such as regulating, throttling,
metering, or needle valves. For example, needle valves have elongated conically-tapered discs
and matching seats for fine flow control. For some valves, there may be a mechanism to indicate
by how much the valve is open, but in many cases other indications of flow rate are used, such as
separate flow meters.
In plants with remote-controlled process operation, such as oil refineries and petrochemical
plants, some 2-way valves can be designated as normally closed (NC) or normally open (NO)
during regular operation. Examples of normally-closed valves are sampling valves, which are
only opened while a sample is taken. Other examples of normally-closed valves are emergency
shut-down valves, which are kept open when the system is in operation and will automatically
shut by taking away the power supply. This happens when there is a problem with a unit or a
section of a fluid system such as a leak in order to isolate the problem from the rest of the
system. Examples of normally-open valves are purge-gas supply valves or emergency-relief
valves. When there is a problem these valves open (by switching them 'off') causing the unit to
be flushed and emptied.
Although many 2-way valves are made in which the flow can go in either direction between the
two ports, when a valve is placed into a certain application, flow is often expected to go from one
certain port on the upstream side of the valve, to the other port on the downstream side.
Pressure regulators are variations of valves in which flow is controlled to produce a certain
downstream pressure, if possible. They are often used to control flow of gas from a gas cylinder.
A back-pressure regulator is a variation of a valve in which flow is controlled to maintain a
certain upstream pressure, if possible.
Three-port valves
Valves with three ports serve many different functions. A few of the possibilities are listed here.
Three-way ball valves come with a T- or L- shaped fluid passageways inside the rotor. The T
valve might be used to permit connection of one inlet to either or both outlets or connection of
the two outlets. The L valve could be used to permit disconnection of both or connection of
either but not both of two inlets to one outlet.
Shuttle valves automatically connect the higher pressure inlet to the outlet while (in some
configurations) preventing flow from one inlet to the other.
Single handle mixer valves produce a variable mixture of hot and cold water at a variable flow
rate under control of a single handle.
Thermostatic mixing valves mix hot and cold water to produce a constant temperature in the
presence of variable pressures and temperatures on the two input ports.
Four-port valves
A 4-port valve is a valve whose body has four ports equally spaced round the body and the disc
has two passages to connect adjacent ports. It is operated with two positions.
Control
A sailor aboard a ship operates the wheel controlling a fuel valve.
Many valves are controlled manually with a handle attached to the stem. If the handle is turned
ninety degrees between operating positions, the valve is called a quarter-turn valve. Butterfly,
ball valves, and plug valves are often quarter-turn valves. If the handle is circular with the stem
as the axis of rotation in the center of the circle, then the handle is called a handwheel. Valves
can also be controlled by actuators attached to the stem. They can be electromechanical actuators
such as an electric motor or solenoid, pneumatic actuators which are controlled by air pressure,
or hydraulic actuators which are controlled by the pressure of a liquid such as oil or water.
Actuators can be used for the purposes of automatic control such as in washing machine cycles,
remote control such as the use of a centralised control room, or because manual control is too
difficult such as when the valve is very large. Pneumatic actuators and hydraulic actuators need
pressurised air or liquid lines to supply the actuator: an inlet line and an outlet line. Pilot valves
are valves which are used to control other valves. Pilot valves in the actuator lines control the
supply of air or liquid going to the actuators.
The fill valve in a toilet water tank is a liquid level-actuated valve. When a high water level is
reached, a mechanism shuts the valve which fills the tank.
In some valve designs, the pressure of the flow fluid itself or pressure difference of the flow fluid
between the ports automatically controls flow through the valve.
Other considerations
Valves are typically rated for maximum temperature and pressure by the manufacturer. The
wetted materials in a valve are usually identified also. Some valves rated at very high pressures
are available. When a designer, engineer, or user decides to use a valve for an application, he/she
should ensure the rated maximum temperature and pressure are never exceeded and that the
wetted materials are compatible with the fluid the valve interior is exposed to. In Europe, valve
design and pressure ratings are subject to statutory regulation under the Pressure Equipment
Directive 97/23/EC (PED).[2]
Some fluid system designs, especially in chemical or power plants, are schematically represented
in piping and instrumentation diagrams. In such diagrams, different types of valves are
represented by certain symbols.
Valves in good condition should be leak-free. However, valves may eventually wear out from use
and develop a leak, either between the inside and outside of the valve or, when the valve is shut
to stop flow, between the disc and the seat. A particle trapped between the seat and disc could
also cause such leakage.
Images