Product-

catalogue
BRONZE BARS AND BEARINGS

Your first choice in bronze

Sisällys
Contents

The design of Slide Bearings pages 3 – 4

Bars alloy JM1 JM3 JM5 JM7

Round Bars page 5 9 12 14
Hollow Bars page 6 10 13 15
Rectangular Bars page 8 11
Hexagonal Bars page 8 11

Bearings
Johnson bearings J page 16
Johnson flanged bearings JF page 17
Oil bronze bearings, straight pages 18 – 19
Oil bronze bearings, flanged page 20
Drymet Radial bearings page 21
Drymet Thrust bearings page 22
Frimet Radial bearings, straight pages 23 – 24
Frimet Radial bearings, flanged pages 25
Frimet Thrust bearings page 26
Rolled bronze bearings page 27
Rolled flanged bearings page 28
Technical data pages 30 – 37
The design of Slide Bearings

Loading capacity

The loading capacity of a bearing with an inside diameter of d mm, length

1 mm and load F Newton, is calculated as follows:

p= F N/mm2
dxl
With sliding speed < 1m/min, in intermittent operation, a surface pressu-
re of half of the yield stress value of the material is permitted.

With sliding speed >1m/min, or continuous operation – the so-called PV-

value, Pressure Velocity, (N/mm2 x m/sec) is used to determine maximum
load capacity. For most bronze grades a PV value of 1.75 N/mm x m/sec
is permitted. An axial movement normally allows for a greater PV value.

Lubrication

The lubrication groove is very important in mounted bearings. Poor

lubrication is often the fault of flawed lubrication grooves. In hydrodynamic
lubrication the groove should not be situated in the load area. With radial
reciprocating movement, place the grooves in the load area, the distance
of the grooves should be <2 x angle of movement. Solid lubricants can be
used in sliding speeds of under 0.5 m/sec.

Things to remember in design:

- the lubrication grooves are placed perpendicularly against the direction
of movement
- great sliding speed = viscous lubricant
- slow sliding speed = rigid lubricant
- viscosity is chosen according to running temperature

Technical services

Our technical advisors are ready to assist in the choice of correct material
and bearing type.

Bearing clearance

For oil lubricated bearings a clearance of 1.5–2.5 ‰ of the inside

diameter of the bearing is suggested. For grease lubricated bearings the
clearance should be two times greater. For back-and-forth movement a
clearance as small as possible is used (0.5– 1‰). In high temperatures
the clearance should be bigger than normally.

3
The design of Slide Bearings, cont.

Mating material

-a  t least 100HB harder than bronze

- for tin bronze alloys a mating material of minimum 300HB
- for aluminum bronze alloys a mating material of a minimum 400HB
-o  ptimal mating material 500HB
- recommended surface finish <1 Ra
- for stainless steel martensitic grades. An austenitic sliding surface
should be hard chromed.

Friction
The coefficient of friction for the bronze bearing:

- in hydrodynamic lubrication = 0.001–0.02

- in the movement area = 0.02–0.08
- in a mixed friction area = 0.08–0.15
-s  olid lubrication = 0.08–0.25

Tolerance and recommendations for bearing housing and axles

Our selection covers seven different types of slide bearings designed for
demanding different operations:

-C
 ast bronze bearings for grease and oil lubrication. Over 200 standard
size bearings from stock, (max D 210) Special size bearings according
to order.
-S
 intered, self-lubricating sliding bearings. Over 250 standard diameter
bearings from stock (max D 100 mm).
-S
 elf-lubricating Frimet multiple-layer bearings. Flanged and straight. Over
250 standard diameter bearings from stock (radial bearings max D 160
mm, axial bearings max D 65 mm).
-S
 traight and flanged rolled bronze bearings, equipped with grease
pockets and especially suitable for reciprocating movements.
-B
 imet multiple-layer bearings for grease lubrication. Over 75 standard
diameter bearings from stock (max D 75 mm).
-S
 elf-lubricating, equipped with solid lubricant Oiles 500 bronze bearings.
Base material and lubricant are chosen according to operation (max.
load 90 N/mm2).

4
BARS

JM 1 Round Bars

ALLOY Gunmetal COLOUR CODE

JM 1–15 EN 1982 – CuSn5Zn5Pb5 – C orange

Order instructions: Tolerances:

Round bar D-length mm, JM 1-15 D10–D18 mm h10

D19–D50 mm h11
Other sizes and round bars for automatic
machining are produced by order, Diameter tolerance: +IT14, -0
max D = 1220 mm.
D

Standard Dimensions

Diameter Weight Diameter Weight Diameter Weight

[mm] [kg/m] [mm] [kg/m] [mm] [kg/m]
13 1.2 51 18.2 142 140.9
16 1.8 56 21.9 152 161.5
19 2.5 61 26.0 162 183.4
21 3.1 67 31.0 172 207.0
23 3.7 72 35.8 182 232.0
26 4.7 77 41.0 192 258.0
29 5.9 82 46.4 202 285.0
31 6.7 87 52.3 222 344.0
33 7.6 92 58.5 252 444.0
36 9.1 97 65.8 Standard
[mm]
39 10.6 102 72.7 lengths
41 11.8 112 87.7 D13–D61 500, 1000, 2000
43 12.9 122 104.0 D67–D142 500, 1000
46 14.8 132 121.8 D152–D252 500

5
BARS

JM 1 Hollow Bars

ALLOY Gunmetal COLOUR CODE

JM 1 EN 1982 – CuSn5Zn5Pb5 – C orange

Order instructions: Tolerances:

Hollow bar D x d-length mm, JM 1-15 D = +IT14, -0

d = +0, -IT15
Other sizes and hollow bars for automatic machining
d are produced by order, max D = 1220 mm.
D

Standard Dimensions

Dxd Weight Dxd Weight Dxd Weight Dxd Weight

[mm] [kg/m] [mm] [kg/m] [mm] [kg/m] [mm] [kg/m]
26 x 13 3.5 77 x 23 37.7 107 x 63 52.2 192 x 128 143.1
x 18 2.5 x 28 35.9 x 73 42.8 x 148 104.5
29 x 13 4.7 x 33 33.8 x 78 37.5 x 168 60.4
x 18 3.6 x 38 31.4 x 83 31.9 200+  
31 x 13 5.5 x 43 28.5 x 88 25.9 202 x 98 218.0
x 18 4.5 x 48 25.3 112 x 38 77.6 x 138 152.0
33 x 13 6.4 x 53 21.8 x 48 71.5 x 158 110.7
x 18 5.3 x 58 17.9 x 58 64.1 x 178 63.7
x 23 3.9 x 63 13.7 x 68 55.3 212 x 148 161.0
36 x 13 7.9 82 x 28 41.5 x 78 45.1 x 168 116.8
x 18 6.8 x 33 39.4 x 88 33.6 x 178 92.6
x 23 5.4 x 38 36.9 x 93 27.2 x 188 66.0
39 x 26 5.9 x 43 34.1 117 x 63 67.9 222 x 98 277.2
x 28 5.2 x 48 30.9 x 73 58.4 x 148 191.3
41 x 13 10.6 x 53 27.4 x 83 47.5 x 168 147.1
x 18 9.5 x 58 23.5 x 93 35.2 x 178 123.0
x 23 8.1 x 63 19.3 x 98 28.6 x 188 97.4
x 28 6.3 x 68 14.7 122 x 68 71.7 232 x 158 201.6
43 x 26 8.2 87 x 28 47.4 x 78 61.5 x 178 154.7
x 33 5.3 x 33 45.3 x 88 49.2 x 188 129.1
46 x 13 13.6 x 38 42.8 x 98 36.9 x 198 102.1
x 18 12.5 x 43 40.0 x 103 29.9 242 x 168 212.0
x 23 11.1 x 48 36.8 127 x 63 85.0 x 188 162.2
x 28 9.3 x 53 33.3 x 73 75.5 x 198 135.3

6
BARS

JM 1 Hollow Bars (cont.)

ALLOY Gunmetal COLOUR CODE

JM 1 EN 1982 – CuSn5Zn5Pb5 – C orange

Standard Dimensions
Dxd Weight Dxd Weight Dxd Weight Dxd Weight
[mm] [kg/m] [mm] [kg/m] [mm] [kg/m] [mm] [kg/m]
x 33 7.2 x 58 12.7 x 83 64.6 x 208 106.9
51 x 18 15.9 x 58 29.4 x 93 52.3 252 x 178 222.3
x 23 14.5 x 63 25.2 x 103 38.6 x 198 169.8
x 28 12.7 x 68 20.6 x 108 31.2 x 208 141.4
x 33 10.6 x 73 15.7 132 x 78 79.2 x 218 111.6
x 38 8.1 92 x 28 53.7 x 88 67.6 262 x 218 147.6
56 x 18 19.6 x 33 51.5 x 98 53.9 x 228 116.4
x 23 18.2 x 38 49.0 x 108 40.2 272 x 168 319.7
x 28 16.4 x 43 46.2 137 x 73 93.9 x 228 153.7
x 33 14.3 x 48 43.1 x 93 70.7 x 238 121.1
x 38 11.8 x 53 39.5 x 103 57.0 282 x 238 159.9
x 43 9.0 x 58 35.6 142 x 58 117.4 x 248 125.9
61 x 18 23.7 x 63 31.4 x 78 98.4 292 x 188 348.8
x 23 22.3 x 68 26.8 x 98 73.0 x 248 166.0
x 28 20.5 x 73 21.9 x 108 58.7 302 x 198 363.3
x 33 18.4 x 78 16.6 x 118 43.6 x 258 172.1
x 38 15.9 97 x 38 56.6 147 x 103 76.9 332 x 273 249.4
x 43 13.1 x 43 52.8 x 123 45.3 362 x 293 315.8
x 48 9.9 x 48 49.6 152 x 88 107.3 392 x 343 251.6
67 x 18 29.1 x 53 46.1 x 98 94.3    
x 23 27.7 x 58 42.3 x 108 79.9
x 28 25.9 x 63 38.0 x 118 64.1
x 33 23.8 x 68 33.4 x 128 47.0
x 38 21.3 x 73 28.5 162 x 98 116.3    
x 43 18.5 x 78 23.2 x 118 86.1    
x 48 15.3 x 83 17.6 x 128 68.9    
x 53 11.7 100+   x 138 50.3    
72 x 18 34.0 102 x 38 62.6 172 x 108 125.2    
x 23 32.5 x 48 56.6 x 128 92.2    
x 28 30.8 x 58 49.2 x 138 73.6    
x 33 28.6 x 68 40.4 x 148 53.7  Standard
[mm]
x 38 26.1 x 73 35.0 182 x 118 134.1 lengths
x 43 23.3 x 78 30.2 x 138 98.4 D26–D56 500,
1000,
x 48 20.1 x 83 24.6 x 148 78.4 2000
x 53 16.6 x 88 18.6 x 158 57.0 D61–D500 500, 1000

7
BARS

JM 1 Rectangular and Hexagonal Bars

ALLOY Gunmetal COLOUR CODE

JM 1–15 EN 1982 – CuSn5Zn5Pb5 – C orange

B Order instructions: Tolerances: Order instructions: Tolerances:

Rectangular bar +IT15, -0 Hexagonal bar AV h11

AXB-length mm, AXB-length mm,
A JM 1-15 JM 1-15
Other sizes are AV Other sizes are
produced by order. produced by order.

Standard Dimensions
Rectangular Rectangular Hexagonal
AxB Weight AxB Weight AV Weight
[mm] [kg/m] [mm] [kg/m] [mm] [kg/m]
32 x 32 9.1 102 x 12 10.9 17 2.2
42 x 42 15.7 x 14 12.7 18 2.5
52 x 12 5.6 x 18 16.3 20 3.1
x 14 6.5 x 22 20.2 22 3.7
x 18 8.3 122 x 18 19.5 23 4.1
x 22 10.2 x 22 23.9 24 4.4
x 52 24.1 142 x 18 22.7 26 5.2
67 x 12 7.2 x 22 27.8 28 6.0
x 14 8.3 162 x 18 26.0 30 6.9
x 18 10.7 x 22 31.7 32 7.9
x 22 13.1 182 x 18 29.2 34 8.9
x 32 19.1 x 22 35.6 36 10.0
82 x 12 8.8 202 x 18 32.4 38 11.1
x 14 10.2 x 22 39.6 41 13.0
x 18 13.1     44 14.9
x 22 16.1     46 16.3
        50 19.3
        52 20.9

8
BARS

JM 3 Round Bars

ALLOY TIN BRONZE COLOUR CODE

JM 3–15 EN 1982 – CuSn12 – C green

Order instructions: Tolerances:

Round bar D-length mm, JM 3-15 D10–D18 mm h10

D19–D50 mm h11
Other sizes are produced by order,
max D = 1220 mm. Diameter tolerance:
+IT14, -0
D

Standard Dimensions

Diameter Weight Diameter Weight Diameter Weight

[mm] [kg/m] [mm] [kg/m] [mm] [kg/m]
13 1.2 51 18.2 142 140.9
16 1.8 56 21.9 152 161.5
19 2.5 61 26.0 162 183.4
21 3.1 67 31.0 172 207.0
23 3.7 72 35.8 182 232.0
26 4.7 77 41.0 192 258.0
29 5.9 82 46.4 202 285.0
31 6.7 87 52.3 222 344.0
33 7.6 92 58.5 252 444.0
36 9.1 97 65.8 Standard
[mm]
39 10.6 102 72.7 lengths
41 11.8 112 87.7 D13–D61 500, 1000, 2000
43 12.9 122 104.0 D67–D142 500, 1000
46 14.8 132 121.8 D152–D252 500

9
BARS

JM 3 Hollow Bars

ALLOY TIN BRONZE COLOUR CODE

JM 3–15 EN 1982 – CuSn12 – C green

Order instructions: Tolerances:

Hollow bar D-length mm, JM 3-15 D = +IT14, -0

d = +0, -IT15
Other sizes are produced by order,
d max D = 1220 mm.
D

Standard Dimensions

Dxd Weight Dxd Weight Dxd Weight Dxd Weight

[mm] [kg/m] [mm] [kg/m] [mm] [kg/m] [mm] [kg/m]
26 x 13 3.5 61 x 28 20.5 82 x 58 23.5 122 x 98 36.9
29 x 13 4.7 x 38 15.9 87 x 58 29.4 127 x 63 85.0
31 x 13 5.5 x 48 9.9 92 x 48 43.1 132 x 98 54.7
33 x 13 6.4 67 x 43 18.5 x 68 26.8 142 x 78 98.4
36 x 18 6.8 72 x 18 34.0 97 x 68 33.4 152 x 118 64.1
41 x 18 9.5 x 28 30.8 102 x 48 56.6 162 x 98 116.3
43 x 26 8.2 x 38 26.1 107 x 63 52.2 182 x 128 117.5
46 x 23 11.1 x 48 20.1 112 x 48 71.5 202 x 98 218.0
x 33 7.2 x 53 16.6 107 x 63 52.2 x 138 152.0
51 x 18 15.9 77 x 53 21.8 112 x 48 71.5 232 x 158 201.6
x 28 12.7 82 x 28 41.5 x 78 45.1 242 x 168 212.0
x 38 8.1 x 43 34.1 117 x 73 58.4 272 x 168 319.7
56 x 33 14.3 x 58 23.5 122 x 68 71.7 302 x 198 363.3

10
BARS

JM 3 Rectangular and Hexagonal Bars

ALLOY TIN BRONZE COLOUR CODE

JM 3–15 EN 1982 – CuSn12 – C green

B Order instructions: Tolerances:

A x B -length mm, JM 3-15 +IT15, -0

A Other sizes are produced by order.

Standard Dimensions
AxB Weight AxB Weight
[mm] [kg/m] [mm] [kg/m]
32 x 32 9.1 102 x 12 10.9
42 x 42 15.7 x 14 12.7
52 x 12 5.6 x 18 16.3
x 14 6.5 x 22 20.2
x 18 8.3 122 x 18 19.5
x 22 10.2 x 22 23.9
x 52 24.1 142 x 18 22.7
67 x 12 7.2 x 22 27.8
x 14 8.3 162 x 18 26.0
x 18 10.7 x 22 31.7
x 22 13.1 182 x 18 29.2
x 32 19.1 x 22 35.6
82 x 12 8.8 202 x 18 32.4
x 14 10.2 x 22 39.6
x 18 13.1    
x 22 16.1    

Standard lengths
500 1000 2000
[mm]

11
BARS

JM 5 Round Bars

ALLOY Leaded tin bronze COLOUR CODE

JM 5–15 EN 1982 – CuSn10Pb10 – C blue

Order instructions: Tolerances:

Round bar D-length mm, JM 5-15 D = +IT14, -0

Other sizes are produced by order,

max D = 1220 mm.
D

Standard Dimensions
Diameter Weight
[mm] [kg/m]
21 3.1
26 4.7
31 6.7
41 11.8
51 18.2
61 26.0
72 35.8
82 46.4
92 58.5
102 72.7
112 87.7
122 104.0

Standard lengths  [mm]

D13–D61 500, 1000, 2000

D72–D122 500, 1000

12
BARS

JM 5 Hollow Bars

ALLOY Leaded tin bronze COLOUR CODE

JM 5–15 EN 1982 – CuSn10Pb10 – C blue

Order instructions: Tolerances:

Hollow bar D x d –length mm, JM 5-15 D = +IT14, -0

d = +0, -IT15
Other sizes are produced by order.
d max D = 1220 mm.
D

Standard Dimensions

Diameter Weight Diameter Weight

[mm] [kg/m] [mm] [kg/m]
26 x 13 3.5 61 x 18 23.7
29 x 13 4.7 x 48 9.9
31 x 13 5.5 82 x 28 41.5
33 x 18 5.3 102 x 58 49.2
36 x 18 6.8 127 x 63 85.0
41 x 18 9.5 162 x 98 116.3
43 x 26 8.2 202 x 98 218.0
46 x 13 13.6    
x 23 11.1
Standard lengths [mm]
x 33 7.2
51 x 18 15.9 D26–D51 500, 1000, 2000
x 28 12.7 D61–D500 500, 1000

13
BARS

JM 7 Round Bars

ALLOY Aluminum bronze COLOUR CODE

JM 7–15/20 EN 1982 – CuAl10Fe5Ni5 – C white

Order instructions: Tolerances:

Round bar D-length mm, JM 7-20 D10–D18 = h10

D19–D50 = h11
Other sizes are produced by order, D>51 = +IT14, -0
max D = 1220 mm.
D

Standard Dimensions

Diameter Weight Diameter Weight Diameter Weight

[mm] [kg/m] [mm] [kg/m] [mm] [kg/m]
10 0.6 56 18.7 142 120.4
13 1.0 61 22.2 152 137.9
16 1.5 67 26.0 162 156.7
19 2.2 71 30.1 182 197.8
21 2.6 76 34.5 192 220.1
23 3.2 81 39.2    
26 4.0 86 44.2    
31 5.7 91 49.4    
33 6.5 97 56.2 Standard
 [mm] 
36 7.7 102 62.1 lengths
39 9.1 112 74.9 D10–D61 500, 1000,
41 10.0 122 88.9 2000
46 12.6 132 104.0 D66–D142 500, 1000
51 15.5 135 108.7 D152–D192 500

14
BARS

JM 7 Hollow Bars

ALLOY Aluminum bronze COLOUR CODE

JM 7–15/20 EN 1982 – CuAl10Fe5Ni5 – C white

Order instructions: Tolerances:

Hollow bar D x d-length mm, JM 7-15 D<162 = +IT14, -0 d

= +0, -IT15
Other sizes are produced by order,
d max D = 1220 mm. D>162 = +IT16, -0 d
= +0, -IT15
D

Standard Dimensions

Dxd Weight Dxd Weight Dxd Weight Dxd Weight

[mm] [kg/m] [mm] [kg/m] [mm] [kg/m] [mm] [kg/m]
33 x 18 4.6 72 x 23 27.8 102 x 48 48.4 172 x 108 107.0
42 x 28 5.9 x 38 22.3 x 58 42.0 182 x 128 99.9
47 x 23 10.0 x 48 17.2 x 68 34.5 192 x 148 89.3
x 28 8.5 x 58 10.9 x 78 25.8 202 x 148 112.8
52 x 18 14.2 77 x 58 15.3 112 x 48 61.1 212 x 158 119.2
x 23 13.0 82 x 38 31.5 x 58 54.8 222 x 168 125.7
x 28 11.5 x 48 26.4 x 68 47.3 232 x 178 132.1
x 38 7.5 x 58 20.1 x 88 28.7 242 x 188 138.6
57 x 43 8.4 x 68 12.5 122 x 68 61.2 252 x 178 189.9
62 x 18 21.0 87 x 38 36.6 x 88 42.6 262 x 198 175.7
x 28 18.3 x 58 25.1 x 98 31.5 282 x 218 191.0
x 38 14.3 92 x 48 36.8 132 x 78 67.7 302 x 198 310.4
x 48 9.2 x 58 30.4 142 x 88 74.1 322 x 238 280.8
67 x 43 15.8 x 68 22.9 152 x 98 80.6 332 x 248 290.9
        162 x 118 73.5 362 x 293 269.8
402 x 348 241.8

15
BEARINGS

Johnson Bearings J

ALLOY Gunmetal
JM 1 EN 1982 – CuSn5Zn5Pb5 – C

Order instructions: Sizes d <12 mm are produced without lubrica-

d D tion groove. Others with lubrication groove
Bearing J d x L parallel to the shaft.

Not all sizes are in stock.

L

Standard Dimensions
Diameters Length series L Diameters Length series L
[mm] [mm] [mm] [mm]
d D 1 2 3 d D 1 2 3
5 10 6 8 10 75 90 70 100 140
6 12 6 8 12 80 95 70 100 140
7 12 8 10 12 85 100 70 100 140
8 14 8 12 16 90 110 80 120 160
9 14 10 16 20 95 115 80 120 160
10 16 10 16 20 100 120 80 120 160
12 18 12 16 25 105 125 80 120 160
14 20 12 20 30 110 130 80 140 200
15 22 16 20 30 120 140 80 140 200
16 22 16 20 30 130 150 90 140 200
17 25 16 20 30 140 160 90 160 200
18 25 16 20 30 150 170 100 160 240
20 28 20 20 40 160 180 100 160 240
22 32 20 30 40 170 190 100 160 240
25 35 25 30 50 180 200 100 160 240
28 40 25 35 50 190 210 120 200 300
30 40 30 45 60 200 220 120 200 300
35 45 35 50 70 210 230 120 200 300
40 50 40 60 80 220 240 140 250 350
45 55 45 60 80 230 250 140 250 350
50 60 50 70 100 240 260 140 250 350
55 70 50 70 100 250 270 140 250 350
60 75 60 90 120          
65 80 60 90 120          
70 85 60 90 120          

16
BEARINGS

Johnson Flanged Bearings JF

ALLOY Gunmetal
JM 1 EN 1982 – CuSn5Zn5Pb5 – C

b
Order instructions: Sizes d <12 mm are produced without lubrica-
tion groove. Others with lubrication groove
Flanged bearing JF d x L parallel to the shaft.
D1 d D
Not all sizes are in stock.

Standard Dimensions
Diameters Length series L Diameters Length series L
[mm] [mm] [mm] [mm]
d D D1 B 1 2 d D D1 B 1 2
5 10 12 2   6 75 90 100 8 40 70
6 12 14 2   6 80 95 105 8 40 70
7 12 16 3   8 85 100 110 8 40 70
8 14 18 3   8 90 110 120 8 50 80
9 14 18 3 8 10 95 115 125 8 50 80
10 16 20 3 8 10 100 120 130 8 50 80
12 18 22 3 10 12 105 125 135 8 50 80
14 20 25 3 10 12 110 130 140 8 50 80
15 22 28 3 12 16 120 140 150 8 50 80
16 22 28 4 12 16 130 150 165 10 60 90
17 25 32 4 12 16 140 160 175 10 60 90
18 25 32 4 12 16 150 170 185 10 70 100
20 28 35 4 16 20 160 180 195 10 70 100
22 32 40 5 16 20 170 190 205 10 70 100
25 35 45 5 16 25 180 200 215 10 70 100
28 40 50 5 16 25 190 210 225 10 80 120
30 40 50 5 20 30 200 220 235 10 80 120
35 45 55 5 20 35 210 230 245 10 80 120
40 50 60 6 25 40 220 240 255 10 100 140
45 55 65 6 30 45 230 250 265 10 100 140
50 60 70 6 30 50 240 260 275 10 100 140
55 70 80 8 30 50 250 270 285 10 100 140
60 75 85 8 35 60            
65 80 90 8 35 60            
70 85 90 8 35 60            

17
BEARINGS

Oil Bronze Bearings, straight

SMS 777 and SS2991 (ISO 2795)

Order instructions:
d D
Bearing 777 d / D x L

Self lubricating sintered oil bronze bearing

L

Standard Dimensions
Diameters Length series L Diameters Length series L
[mm] [mm] [mm] [mm]
d D 1 2 3 4 5 d D 1 2 3 4 5
2 4 4 - - - - 25 30 20 25 30 - -
3 8 4 - - - - 25 32 20 25 30 35 -
4 8 4 6 8 - - 25 35 25 35 50 - -
4 10 8 - - - - 25 45 35 - - - -
5 10 6 8 10 - - 30 35 20 25 30 - -
5 12 10 - - - - 30 38 20 25 30 40 -
6 9 4 6 10 - - 30 40 30 45 60 - -
6 10 4 6 10 - - 30 50 60 - - - -
6 12 6 8 12 - - 35 41 25 35 40 - -
6 14 12 - - - - 35 45 25 35 40 50 70
8 11 6 8 12 - - 40 46 30 40 50 - -
8 12 6 8 12 - - 40 50 30 40 50 60 80
8 14 8 12 16 - - 45 51 35 45 55 - -
8 18 16 - - - - 45 55 35 45 55 60 65
10 14 8 10 16 - - 45 65 80 - - - -
10 16 8 10 16 20 - 50 60 35 50 70 100 -
10 22 20 - - - - 50 70 70 - - - -
12 16 8 12 20 - - 55 65 40 55 70 - -
12 18 8 12 16 20 25 55 70 70 - - - -
12 25 25 - - - - 60 68 50 60 70 - -
14 18 10 14 20 - - 60 72 50 60 70 - -
14 20 10 12 14 20 30 60 75 60 90 - - -

18
BEARINGS

Oil Bronze Bearings, straight

SMS 777 and SS2991 (ISO 2795), cont.

Standard Dimensions
Diameters Length series L Diameters Length series L
[mm] [mm] [mm] [mm]
d D 1 2 3 4 5 d D 1 2 3 4 5
14 28 30 - - - - 60 85 90 - - - -
15 19 10 15 25 - - 65 75 60 90 - - -
15 21 10 15 25 - - 65 80 60 90 - - -
15 22 16 20 30 - - 70 80 60 90 - - -
15 30 30 - - - - 70 85 60 90 - - -
16 20 12 16 25 - - 75 85 70 100 - - -
16 22 12 16 20 25 30 75 90 70 100 - - -
16 32 30 - - - - 75 100 100 - - - -
18 22 12 18 30 - - 80 90 70 100 - - -
18 24 12 18 30 - - 80 95 70 100 - - -
18 25 16 20 30 - - 80 105 100 - - - -
18 35 30 - - - - 85 95 100 - - - -
20 25 15 20 25 - - 85 100 100 - - - -
20 26 15 20 25 30 - 90 105 80 - - - -
20 28 20 30 40 - - 90 110 80 - - - -
20 40 40 - - - - 100 120 80 - - - -
22 27 15 20 25 - - - - - - - - -
22 32 20 30 - - - - - - - - - -

19
BEARINGS

Oil Bronze Bearings, flanged

SMS 779 and SS 2992 (ISO 2795)

b Order instructions: Porous bronze bearing with oil lubrication based

function. Parent material analysis: Cu 89.5%, SN
Flanged bearing 779 9.3% and C 1.2%. Oil content ca. 25 volume-%.
D1 d D d / D x L - D1 x B Most typical field of application is higher (over 0.3
m/s) sliding speed in radial movements, but use at
Self-lubricating sintered oil lower sliding speeds is also possible. Surface load
bronze bearing. will maximum be 30 N/mm2.
L

Standard Dimensions

Diameters Length series L Diameters Length series L

[mm] [mm] [mm] [mm]
d D D1 B 1 2 3 4 d D D1 B 1 2 3 4
3 5 8 1.5 4 - - - 20 26 32 4 15 20 25 30
3 6 9 1.5 4 - - - 20 28 35 4 16 20 - -
4 8 10 1.5 6 - - - 25 32 39 3.5 20 25 30 -
4 8 12 2 4 6 - - 25 35 45 5 16 25 - -
5 9 13 2 4 5 8 - 30 38 46 4 20 25 30 -
5 10 12 2 6 - - - 30 40 50 5 20 30 - -
6 10 14 2 4 6 10 - 35 45 55 5 20 25 35 40
6 12 14 2 6 - - - 40 50 60 5 30 40 50 -
8 12 16 2 6 8 12 - 40 50 60 6 25 40 - -
8 14 18 3 8 - - - 45 55 65 5 35 45 55 -
10 16 20 3 8 10 - - 45 55 65 6 30 45 - -
10 16 22 3 8 10 16 - 50 60 70 5 35 50 - -
12 18 22 3 10 12 - - 50 60 70 6 30 50 - -
12 18 24 3 8 12 20 - 60 72 84 6 50 60 - -
14 20 25 3 10 12 - - 60 75 85 8 35 60 - -
14 20 26 3 10 14 20 - 70 85 95 8 60 - - -
15 21 27 3 10 15 25 - 80 95 105 8 70 - - -
15 22 28 3 12 16 - - 90 110 120 8 50 - - -
16 22 28 3 12 16 25 - 100 120 130 8 80 - - -
16 22 28 4 12 16 - - - - - - - - - -
18 24 30 3 12 18 30 - - - - - - - - -
18 25 32 4 12 16 - - - - - - - - - -

20
BEARINGS

Drymet Radial Bearings

Drymet 701

Order instructions: Thin-walled multilayer steel chassis bearing, with an

oil-saturated acetal plastic surface. The bearing is
d D Drymet 701-dL self-lubricating however, additional grease or oil lu-
brication is recommended. Especially in low sliding
Steel sintered bronze layer oil speeds, intermittent operation, reciprocating and ra-
L impregnated acetal plastic dial movements and in heavy loads, the advantages
of this bearing are considerable. Maximum surface
Other sizes are produced by load ca. 80 N/mm2.
order.

Standard Dimensions

Diameters Length series L Diameters Length series L

[mm] [mm] [mm] [mm]
d D 1 2 3 4 d D 1 2 3 4
5 7 5 - - - 45 50 30 - 40 60
6 8 6 10 - - 50 55 30 40 60 -
8 10 8 10 12 - 55 60 - 40 60 -
10 12 10 15 20 - 60 65 - 40 60 -
12 14 10 15 20 - 65 70 - 40 60 -
14 16 - 15 20 - 70 75 - 40 80 -
15 17 15 - 25 - 75 80 - 40 80 -
16 18 15 20 25 - 80 85 - 40 80 -
18 20 15 20 25 - 85 90 - 40 80 -
20 23 15 20 25 30 90 95 40 50 90 100
22 25 15 20 25 30 100 105 - 50 95 100
24 27 15 20 25 30 110 115 - 50 95 100
25 28 15 20 25 30 120 125 - 50 95 100
28 32 - 25 - 40 130 135 - 80 - 125
30 34 20 25 30 40 140 145 - - 100 -
35 39 20 25 30 40 150 155 - - 100 -
35 39 - - - 50 160 165 - - - 125
40 44 20 30 - 50 - - - - - -
40 45 25 - 40 - - - - - - -

21
BEARINGS

Drymet Thrust Bearings

Drymet 705

d2 Order instructions: Thin-walled multilayer steel chassis bearing, with an

Drymet 705-d oil-saturated acetal plastic surface. The bearing is self-
Self-lubricating lubricating however, additional grease or oil lubrication is
d1 multilayered bearing recommended. Especially in low sliding speeds, intermittent
operation, reciprocating and radial movements and with hea-
Special sizes are vy loads, the advantages of this bearing are considerable.
d produced by order, Maximum surface load ca. 80 N/mm2.
max D = 1200 mm
D

Standard Dimensions
d [mm] D [mm] t [mm] d1 [mm] d2 [mm]
10 20 1.5 15 1.5
12 24 1.5 18 1.5
14 26 1.5 20 2.0
18 32 1.5 25 2.0
20 36 1.5 28 3.0
23 40 1.5 31.5 3.0
28 48 1.5 38 3.0
34 58 1.5 46 3.0
39 66 2.0 52.5 3.0
47 78 2.0 62.5 4.0
50 84 2.5 67 4.0
55 92 2.5 73.5 5.0
60 100 2.5 80 5.0
65 108 2.5 86.5 5.0

22
BEARINGS

Frimet Radial Bearings, straight

Frimet, straight

Order instructions: Material: Steel sintered bronze layer

Frimet, straight d x L Sliding surface: PTFE ja Pb.
d D Self-lubricating mul-
tilayer bearing. Thin-walled multilayer steel chassis bearing with a lead
alloy PTFE surface. The bearing is self-lubricating and is
L Special sizes are recommended for slow movement and high temperatures, in
produced by order. which lubrication oil does not work.

Standard Dimensions
Diameters [mm] Length series L [mm]
d D 1 2 3 4 5 6
Tolerance, Shaft/housing, h6/H6
3 4.5 3 4 5 6 - -
4 5.5 3 4 6 10 - -
Tolerance, Shaft/housing, f7/H7
5 7 5 8 10 - - -
6 8 6 8 10 - - -
8 10 8 10 12 - - -
10 12 8 10 12 15 20 -
12 14 8 10 12 15 20 25
13 15 10 15 20 25 - -
14 16 10 12 15 20 25 -
15 17 10 12 15 20 25 -
16 18 10 12 15 20 25 30
17 19 15 20 25 - - -
18 20 15 20 25 - - -
20 22 10 15 20 25 - -
20 23 10 15 20 25 30 -
22 25 15 20 25 30 - -
24 27 15 20 25 30 - -
25 28 12 15 20 25 30 -
24 28 15 20 25 30 - -
28 32 20 25 30 - - -
30 34 15 20 25 30 40 -
32 36 20 30 40 - - -
35 39 20 30 35 40 50 -
40 44 20 30 40 50 - -
45 50 20 30 40 50 - -
50 55 20 25 30 40 50 60

23
BEARINGS

Frimet Radial Bearings, straight

Frimet, straight (cont.)

Standard Dimensions
Diameters [mm] Length series L [mm]
d D 1 2 3 4 5 6
55 60 20 25 30 40 50 60
60 65 30 40 60 70 - -
65 70 30 35 50 60 70 -
70 75 40 50 60 70 - -
75 80 40 50 60 70 80 -
Tolerance, Shaft/housing, h8/H7
80 85 40 60 100 - - -
85 90 60 100 - - - -
90 95 60 100 - - - -
95 100 60 100 - - - -
100 105 60 70 80 100 115 -
105 110 60 100 115 - - -
110 115 60 100 115 - - -
115 120 60 70 100 115 - -
120 125 60 100 - - - -
125 130 60 100 - - - -
130 135 60 100 - - - -
135 140 60 100 - - - -
140 145 60 100 - - - -
145 150 60 100 - - - -
150 155 60 100 - - - -
155 160 60 100 - - - -
160 165 60 80 100 - - -
165 170 60 100 - - - -
170 175 60 100 - - - -
175 180 60 100 - - - -
180 185 60 100 - - - -
200 205 60 100 - - - -
205 210 60 100 - - - -
210 215 60 100 - - - -
215 220 60 100 - - - -
220 225 60 100 - - - -
230 235 60 100 - - - -
240 245 60 100 - - - -
250 255 60 100 - - - -
280 285 60 100 - - - -
300 305 60 100 - - - -

24
BEARINGS

Frimet Radial Bearings, flanged

Frimet, flanged

Order instructions: Material: Tolerances:

Frimet, flanged d x L Steel sintered bronze layer
D1 d D Sliding surface: PTFE and Pb. Shaft/housing
Limited stock. f7/H7
Thin-walled multilayer steel
L chassis bearing with a lead
alloy PTFE surface. The bearing
is self-lubricating and is recom-
mended for slow movement
and high temperatures, in which
lubrication oil does not work.

Standard Dimensions
Diameters [mm] Length series L [mm]
d D D1 1 2 3 4
6 8 12 4 7 8 -
8 10 15 5.5 7.5 9.5 -
10 12 18 7 9 12 17
12 14 20 7 9 12 17
14 16 22 12 17 - -
15 17 23 9 12 17 -
16 18 24 12 17 - -
18 20 26 12 17 22 -
20 23 30 11.5 16.5 21.5 -
25 28 35 11.5 16.5 21.5 -
30 34 42 16 26 - -
35 39 47 16 26 - -
40 44 53 26 - - -

25
BEARINGS

Frimet Thrust Bearings

Frimet

d2
Order instructions for Material: Steel sintered bronze layer
bearings: Sliding surface: PTFE and Pb.
d1 Frimet, thrust bearing d
Order instructions for strips: Thin-walled multilayer steel chassis bearing with a
Frimet, strip bxt lead alloy PTFE surface. The bearing is self-lubricating
d and is recommended for slow movement and high
Limited stock. temperatures, in which lubrication oil does not work.
D
Standard Dimensions, Frimet Trust bearing
d [mm] D [mm] D2 [mm] d1 [mm] d2 [mm]
10 20 1.5 15 1.5
12 24 1.5 18 1.5
14 26 1.5 20 2.0
16 30 1.5 22 2.0
18 32 1.5 25 2.0
20 36 1.5 28 3.0
22 38 1.5 30 3.0
26 44 1.5 35 3.0
28 48 1.5 38 4.0
32 54 1.5 43 4.0
38 62 1.5 50 4.0
42 66 1.5 54 4.0
48 74 2.0 61 4.0
52 78 2.0 65 4.0
62 90 2.0 76 4.0

Standard Dimensions, Frimet Strips

b [mm] t [mm]
280 1.0 1.5 2.0 2.5 3.0

26
BEARINGS

Rolled Bronze Bearings

BMR 10, straight

Order instructions: Norm: DIN 1494

d D Material: CuSn8 (DIN 17662)
BRM 10, straight d x L
Rolled sliding bearing according to DIN 17662,
made from tin bronze plate by rolling. The sliding
L
surface, storing lubricant, is equipped with grease
pockets.

Standard Dimensions
Diameters Length series L Diameters Length series L
[mm] [mm] [mm] [mm]
d D 1 2 3 4 5 6 d D 1 2
10 12 10 15 20 - - - 90 95 60 100
12 14 10 15 20 - - - 95 100 60 100
13 15 - 15 20 - - - 100 105 60 100
14 16 10 15 20 25 - - 105 110 60 100
15 17 10 15 20 25 - - 110 115 60 100
16 18 10 15 20 20 - - 115 120 60 100
17 19 - 15 20 - - - 120 125 60 100
18 20 - 15 20 25 - - 125 130 60 100
20 22 10 15 20 25 - - 130 135 60 100
20 23 15 20 25 25 30 - 135 140 60 100
22 25 15 20 25 30 - - 140 145 60 100
24 27 15 20 25 30 - - 145 150 60 100
24 28 15 20 25 30 - - 150 155 60 100
25 28 15 20 25 30 50 - 155 160 60 100
28 32 - 20 25 30 - - 160 165 60 100
30 34 15 20 25 30 40 - 165 170 60 100
32 36 - 20 - 30 40 - 170 175 60 100
35 39 20 30 35 40 50 - 175 180 60 100
40 44 20 30 - 40 50 - 180 185 60 100
45 50 20 30 - 40 50 - 200 205 60 100
50 55 20 25 30 40 50 60 205 210 60 100
55 60 20 25 30 40 50 60 210 215 60 100
60 65 30 - 40 - 60 70 215 220 60 100
65 70 30 - - 50 60 70 220 225 60 100
70 75 40 50 60 70 - - 230 240 60 100
75 80 40 50 60 70 80 - 240 250 60 100
80 85 40 - 60 - - 100 250 255 60 100
85 90 - - 60 - - 100 280 285 60 100
- - - - - - - - 300 305 60 100

27
BEARINGS

Rolled Flanged Bearings

BMR 10, flanged

Order instructions: Norm: DIN 1494

BRM 10, flanged d x L Material: CuSn8 (DIN 17662)
D1 d D
Special sizes are produced Rolled sliding bearing according to DIN 17662,
by order and are also made from tin bronze plate by rolling. The sliding
delivered perforated, surface, storing lubricant, is equipped with grease
L max D = 1200 mm pockets.

Standard Dimensions
Diameters Length series L Diameters Length series L
[mm] [mm] [mm] [mm]
d D D1 1 2 d D D1 1 2
25 28 35 15 25 120 125 140 50 90
30 34 45 20 30 130 135 155 60 90
35 39 50 20 35 140 145 165 60 90
40 44 55 25 40 150 155 180 60 90
45 50 60 30 45 160 165 190 60 90
50 55 65 30 50 170 175 200 60 90
55 60 70 30 50 180 185 215 60 90
60 65 75 30 60 190 195 225 60 90
65 70 80 30 60 200 205 235 60 90
70 75 85 40 70 225 230 260 60 90
75 80 90 40 70 250 255 290 60 90
80 85 100 40 80 265 270 305 60 90
90 95 110 50 90 285 290 325 60 90
100 105 120 50 90 300 305 340 60 90
110 115 130 50 90          

28
Technical Data >>

29
TECHNICAL
DATA

Technical information of tool bronze

Cu Al Fe Ni Mn Cr Si
AMPCO Recommendations for use [%] [%] [%] [%] [%] [%] [%]

18 Outstanding sliding and fatigue proper-

ties and excellent wear resistance. Good rest 10.5 3.5        
sliding properties against stainless steel
21 Great hardness and low strain. For
tracks and bending studs in deepdrawing rest 12.8 4.5        
of the bar.
22 Harder than AMPCO 21. For deep draw-
ing of stainless steel, cores, for ejector rest 13.8 5.0        
pins and rollers for tube manufacturing.

25 Bending studs and pressure pistons

in the deep drawing of stainless steel,              
rollers and mandrel.

45 For big mechanical loads in deep drawing

conditions. rest 10.0 3.5 5.0 1.0    

M-4 Good mechanical properties at high

temperatures. rest 11.0 4.8 5.1 1.0    

Cu Al Fe Ni Mn Cr Si
AMPCOLOY Recommendations for use [%] [%] [%] [%] [%] [%] [%]

945 Be free. Option for alloy CuBe2. For

seam-, spot- and project welding of rest           2.8
stainless steel.

940 RWMA 3. For spot welding electrodes for

stainless steel. rest         0.4 0.7
972 RMWA 2. The holders of the electrodes,
for continuous casting of steel and rest         1.1  
aluminium for dies.

30
TECHNICAL
DATA

Tensile 0.2% Yield strength

Other Strenght Proof Hard- Elonga- Density under com- Conduc- Thermal
strength ness tion tivity conductivity
[%] Rm
A [%] [kg/dm
Rp0.2[N/
3
] pression
[N/mm2] HBW [N/mm2] [%] IACS [W/mXKº]
mm2]

<0.5 720 360 190 14 7.45 240    

<2.5 760 410 280 1 7.21 340    

<2.5 720 430 330 0.5 7.06 650    

      >340 0.2 6.93 710    

<0.5 810 520 230 10 7.53 270    

<0.5 990 790 290 8 7.45 730    

Tensile 0.2% Yield strength

Other Strenght Proof Hard- Elonga- Density under com- Conduc- Thermal
strength ness tion tivity conductivity
[%] Rm
A [%] [kg/dm
Rp0.2[N/
3
] pression
[N/mm2] HBW [N/mm2] [%] IACS [W/mXKº]
mm2]

  890 550 290 6 8.65 690 16 140

  660 >510 210 9-13 8.71 630 >26 190

<0.5 448-496 480 150 13 8.87   45 310

31
TECHNICAL
DATA

Casting alloy standards of copper metals

Cu Sn Pb
JM-1 Gunmetal, EN 1982 – CuSn5Zn5Pb5 – C [%] [%] [%]

-15 Most economic and mostly used sliding bearings for common use.
Good wear resistance and sliding qualities.
83.0–87.0 4.0–6.0 4.0–6.0
-03 Not recommended for sliding bearings when sand cast, and not
seawater resistant.

Cu Sn Pb
JM-2 TIN BRONZE, EN 1982 – CuSn10 – C [%] [%] [%]

-15 Great strenght, combined with the best wear resistance. Recom-
mended when strength staying within the dimension under impact
and heavy loads is a requirement. Does not conform to edge
loading. Mating material preferably hard and quenched. Good salt 88.0–90.0 9.0–11.0 0–1.0 
water resistance.
-03 Due to wear resistance the best sand cast alloys are alloys with
plenty of tin (14%)

Cu Sn Pb
JM-3 TIN BRONZE, EN 1982 – CuSn12 – C [%] [%] [%]

-15 Great strength combined with the best wear resistance. Recom-
mended when staying within the dimension under impact and
heavy loads is a requirement. Does not conform to edge loading.
Mating material preferably hard and quenched. Good salt water
85.0–88.5 11.0–13.0  0–0.7
resistance.
-03 Due to wear resistance the best sand cast alloys are alloys with
plenty of tin (14%).

Cu Sn Pb
JM-4 Leaded TIN BRONZE, EN 1982 – CuSn7Pb15 – C [%] [%] [%]

-15 When lubrication is intermittent or otherwise insufficient, these bea-

ring bronzes have the best wear resistance and sliding properties.
The bearing bronzes most suitable for water lubrication. Conforms 74.0–80.0 6.0–8.0 13.0–17.0
to edge loading and have good saltwater resistance.
-03 Noticeably poorer wear resistance.
When the alloying element is marked with an x, this is defined as an impurity and it will not be alloyed.
This may occur within the limits defined by the standard.

32
TECHNICAL
DATA

Tensile 0.2%
Zn Ni Al Fe Mn Density Strenght Proof Brinell-
strength Elongation h
[%] [%] [%] [%] [%] [kg/dm3] Rm  ardness
Rp0.2 A [%]
[N/mm2] HBW
[N/mm2]

≥250 ≥110 ≥13 ≥65

0.60–
4.0–6.0 x  x–0.30  x  8.8
2.00
≥200 ≥90 ≥13 ≥60

0.2%
Tensile
Zn Ni Al Fe Mn Density Proof Elongation hBrinell-
[%] [%] [%] [%] [%] [kg/dm3] RStrenght2 strength
Rp0.2 A [%] ardness
m
[N/mm ] HBW
[N/mm2]

≥280 ≥160 ≥10 ≥80

x–0.5 0–2.0 x x–0.20 x–0.10 8.8

≥250 ≥130 ≥18 ≥70

0.2%
Tensile Proof Brinell-
Zn Ni Al Fe Mn Density Elongation h
[kg/dm3] RStrenght strength  ardness
[%] [%] [%] [%] [%] Rp0.2 A [%]
m
[N/mm2] HBW
[N/mm2]

≥300 ≥150 ≥6 ≥90

x–0.50  0–2.0  x–0.01   x–0.20 x–0.20  8.8

≥260 ≥140 ≥7 ≥80

0.2%
Tensile Proof Brinell-
Zn Ni Al Fe Mn Density Elongation h
[kg/dm3] RStrenght strength  ardness
[%] [%] [%] [%] [%] Rp0.2 A [%]
m
[N/mm2] HBW
[N/mm2]

≥200 ≥90 ≥8 ≥65

0–2.0 0.5–2.0 x x–0.25 x–0.20 9.1

≥170 ≥80 ≥8 ≥60

We also cast other EN 1982 standard alloys on demand. When placing such orders, references are to be made to the norm
and the connected alloy.

33
TECHNICAL
DATA

Casting alloy standards of copper metals

(cont.)

Cu Sn Pb
JM-5 LEADED TIN BRONZE, EN 1982 – CuSn10Pb10 – C [%] [%] [%]

-15 When lubrication is intermittent or otherwise insufficient these bea-

ring bronzes have the best wear resistance and sliding properties.
The best suitable bearing bronzes for water lubrication. Conforms to
edge loading and have good saltwater resistance. 78–82 9.0–11.0 8.0–11.0

-03 Noticeably poorer wear resistance

Cu Sn Pb
JM-6 Aluminum bronze, EN 1982 – CuAl10Fe2 – C [%] [%] [%]

-15 Material possesses great tenacity and high corrosion resistance.

Sliding properties and wear resistance clearly poorer than above
mentioned alloys. Only recommended for sliding bearings when
yield properties of tin bronze are insufficient. Good saltwater 83–89.5 x–0.20 x–0.10
resistance.
-03 Same properties

Cu Sn Pb
JM-7 Aluminum bronze, EN 1982 – CuAl10Fe5Ni5 – C [%] [%] [%]

-15 Material possessing great tenacity and high corrosion resistance.

Sliding properties and wear resistance clearly poorer than above
mentioned alloys. Only recommended in slide bearings when yield
properties of tin bronze are insufficient. Good saltwater resistance. 76.0–83.0  x–0.10  x–0.03

-03 Same properties

-20 Same properties

Cu Sn Pb
JM-15 Manganese bronze, EN 1982 – CuZn35Mn2Al1Fe1 – C [%] [%] [%]

-15 Material possessing great tenacity and high corrosion resistance.

Sliding properties and wear resistance clearly poorer than above
mentioned alloys. Only recommended in slide bearings when yield
properties of tin bronze are insufficient. Good saltwater resistance. 57–65 0–1.0 x–0.5

-03 Same properties

When the alloying element is marked with an x, this is defined as an impurity and it will not be alloyed.
This may occur within the limits defined by the standard.

34
TECHNICAL
DATA

0.2%
Tensile Proof Brinell-
Zn Ni Al Fe Mn Density Elongation h
|kg/dm3] RStrenght strength  ardness
[%] [%] [%] [%] [%] Rp0.2 A [%]
m
[N/mm2] HBW
[N/mm2]

 0–2.0 0–2.0 x  x–0.25  x–0.20 8.9 ≥220 ≥110 ≥8 70

≥180 ≥80 ≥8 ≥60

0.2%
Tensile Proof Brinell-
Zn Ni Al Fe Mn Density Elongation h
|kg/dm3] RStrenght strength  ardness
[%] [%] [%] [%] [%] Rp0.2 A [%]
m
[N/mm2] HBW
[N/mm2]

x–0.50 0–1.5 8.15–10.5 1.5–3.5 0–1.0 7.6 ≥550 ≥200 ≥15 ≥130

≥500 ≥180 ≥18 ≥100

0.2%
Tensile
Zn Ni Al Fe Mn Density Proof Elongation hBrinell-
|kg/dm3] RStrenght strength ardness
[%] [%] [%] [%] [%] Rp0.2 A [%]
m
[N/mm2] HBW
[N/mm2]

≥650 ≥280 ≥13 ≥150

 x–050 4.0–6.0 18.5–10.5 4.0–5.5 0–3.0 7.6

≥600 ≥250 ≥13 ≥140

0.2%
Zn Ni Al Fe Mn Density Tensile Proof Brinell-
Elongation h
[%] [%] [%] [%] [%] |kg/dm3] Strenght2 strength
Rp0.2 A [%]  ardness
Rm[N/mm ] HBW
[N/mm2]

Remain- ≥500 ≥200 ≥18 ≥120

0–6.0 0.5–2.5 0.5–2.0 0.5–3.0 8.2
der

≥450 ≥170 ≥20 ≥110

We also cast other EN 1982 standard alloys on demand. When placing such orders, references are to be made to the norm
and the connected alloy.

35
TECHNICAL
DATA

Tolerances and recommendations for

bearing houses and shafts
J-BUSHING
MOUNTING SHAFT

E8 h9

JF- FLANGED BUSHING

MOUNTING SHAFT

ROLLED BRONZE BEARING BRM 10

SHAFT MOUNTING
Shaft hardness min 150 HB
Sleekness min 1 Ra

36
TECHNICAL
DATA

Tolerances and recommendations for

bearing houses and shafts (cont.)
SINTERED BUSHING SMS 777
MOUNTING SHAFT

SINTERED FLANGED BUSHING

MOUNTING SHAFT

DRYMET 701 AND BIMET 5 RADIAL BEARINGS

MOUNTING SHAFT

37
Oy Johnson Metall AB
Turkkirata 14
33960 Pirkkala, Finland

Tel.
+358 (0)3 342 7700

Fax
+358 (0)3 342 7728

www.johnson-metall.fi