Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Lecture 4 - House Design

Download as pdf or txt
Download as pdf or txt
You are on page 1of 18

Department of Civil Engineering N-W.F.

P UET Peshawar Design of Concrete Structures (CE-405)

Example No.2: Design the roof slab, beam and column of house given in figure 1.1.
Concrete compressive strength (fc´) = 3 ksi.
Steel yield strength (fy) = 40 ksi.
Load on slab:
4″ thick mud.
2″ thick brick tile.
Live Load = 40 psf
9" Brick masonary wall

S1 12' x 16' S1 12' x 16'

13 12" Brick masonary wall


A

1.5" Expansion joint


S2 9' wide

B1 B1

C1
A
R.C.C Column

Figure 1.1: Slabs S1 and S2 to be designed.

Prof. Dr. Qaisar Ali (qaisarali.onlineuet.com) Page 1 of 18


Department of Civil Engineering N-W.F.P UET Peshawar Design of Concrete Structures (CE-405)

Solution: -
(1) Design of slab “S2”:
Step No 1: Sizes.
lb/la = 24.75/8 = 3.09 > 2 “one way slab”
Assume 5″ slab.
Span length for end span according to ACI 8.7 is minimum of:
(i) l = ln+ hf = 8 + (5/12) = 8.42′
(ii) c/c distance between supports = 9.0625′
1.5" Expansion Joint

13 12" Brick Masonary Wall


l n = 8'-0"
9'-0" wide verandah
l n + (6.75 /12) + 0.5 = 9.0625'

Figure 1.2: Section A-A (see figure 1.1 above).

Therefore l = 8.42′
Slab thickness (hf) = (l/20) x (0.4+fy/100000) [for fy < 60000 psi]
= (8.42/20) x (0.4 + 40000/100000) x 12
= 4.04″ (Minimum requirement of ACI 9.5.2.1).
Therefore take hf = 5″
d = hf – 0.75 – (3/8)/2 = 4″

Step No 2: Loading.

Table 1.1: Dead Loads.


Material Thickness (in) γ (kcf) Load = γ x thickness (ksf)
Slab 5 0.15 0.15 x (5/12) = 0.0625
Mud 4 0.12 0.12 x (4/12) = 0.04
Brick Tile 2 0.12 0.12 x (2/12) = 0.02

Prof. Dr. Qaisar Ali (qaisarali.onlineuet.com) Page 2 of 18


Department of Civil Engineering N-W.F.P UET Peshawar Design of Concrete Structures (CE-405)

Service Dead Load (D.L) = 0.0625 + 0.04 + 0.02


= 0.1225 ksf
Service Live Load (L.L) = 40 psf or 0.04 ksf
Factored Load (wu) = 1.2D.L + 1.6L.L
= 1.2 x 0.1225 + 1.6 x 0.04
= 0.211 ksf

Step No 3: Analysis.
Mu = wul2/8 (l = span length of slab)
Mu = 0.211 x (8.42)2/8
= 1.87 ft-k/ft = 22.44 in-k/ft

Step No 4: Design.
Asmin = 0.002bhf (for fy 40 ksi, ACI 10.5.4)
= 0.002 x 12 x 5 = 0.12 in2
a = Asminfy/ (0.85fc′b)
= 0.12 x 40/ (0.85 x 3 x 12) = 0.156 in
ΦMn(min) = ΦAsminfy (d – a/2)
= 0.9 x 0.12 x 40 x (4 – 0.156/2)
= 16.94 in-k < Mu
Therefore,
• As = Mu/ {Φfy (d – a/2)}
Take a = 0.2d
As = 22.44/ {0.9 x 40 x (4 – (0.2 x 4)/2)}
As = 0.173 in2
• a = 0.173 x 40/ (0.85 x 3 x 12) = 0.226 in
As = 22.44/ {0.9 x 40 x (4 – (0.226/2))}
= 0.160 in2
• a = 0.160 x 40/ (0.85 x 3 x 12) = 0.209 in
As = 22.44/ {0.9 x 40 x (4 – (0.209/2))}
= 0.160 in2, O.K.

Prof. Dr. Qaisar Ali (qaisarali.onlineuet.com) Page 3 of 18


Department of Civil Engineering N-W.F.P UET Peshawar Design of Concrete Structures (CE-405)

Using ½″ Φ (#4) {#13, 13 mm}, with bar area Ab = 0.20 in2


Spacing =Area of one bar (Ab)/As
= [0.20 (in2)/0.160 (in2/ft)] x 12 = 15 in
Using 3/8″ Φ (#3) {#10, 10 mm}, with bar area Ab = 0.11 in2
Spacing = Area of one bar (Ab)/As
= [0.11(in2)/0.160(in2/ft)] x 12 = 7.5″ ≈ 6″
Finally use #3 @ 6″ c/c (#10 @ 225 mm c/c).
Shrinkage steel or temperature steel (Ast):
Ast = 0.002bhf
Ast = 0.002 x 12 x 5 = 0.12 in2
Using 3/8″ Φ (#3) {#10, 10 mm}, with bar area Ab = 0.11 in2
Spacing = Area of one bar (Ab)/Asmin
= (0.11/0.12) x 12 = 11″ c/c
Finally use #3 @ 9″ c/c (#10 @ 225 mm c/c).
• Maximum spacing for main steel in one way slab according to ACI 7.6.5 is
minimum of:
i) 3hf =3 x 5 =15″
ii) 18″
Therefore 6″ spacing is O.K.
• Maximum spacing for shrinkage steel in one way slab according to ACI 7.12.2
is minimum of:
i) 5hf =5 x 5 =25″
ii) 18″
Therefore 9″ spacing is O.K.

(2) Design of slab “S1”:


Step No 1: Sizes.
lb/la = 16/12 = 1.33 < 2 “two way slab”
Minimum depth of two way slab is given by formula,
hmin = perimeter/180
= 2 x (16 + 12) x 12/180 = 3.73 in
Assume h = 5″

Prof. Dr. Qaisar Ali (qaisarali.onlineuet.com) Page 4 of 18


Department of Civil Engineering N-W.F.P UET Peshawar Design of Concrete Structures (CE-405)

Step No 2: Loads.
Factored Load (wu) = wu, dl + wu, ll
wu = 1.2D.L + 1.6L.L
wu = 1.2 x 0.1225 + 1.6 x 0.04 (see table 1.1 above)
= 0.147 + 0.064 = 0.211 ksf

Step No 3: Analysis.
The precise determination of moments in two-way slabs with various conditions
of continuity at the supported edges is mathematically formidable and not suited
to design practice. For this reason, various simplified methods have been adopted
for determining moments, shears, and reactions of such slabs.
According to the 1995 ACI Code, all two-way reinforced concrete slab systems,
including edge supported slabs, flat slabs, and flat plates, are to be analyzed and
designed according to one unified method, such as Direct design Method and
Equivalent Frame Method. However, the complexity of the generalized approach,
particularly for systems that do not meet the requirements permitting analysis by
“direct design method” of the present code, has led many engineers to continue to
use the design method of the 1963 ACI Code for the special case of two-way
slabs supported on four sides of each slab panel by relatively deep, stiff, edge
beams.
This method has been used extensively since 1963 for slabs supported at the
edges by walls, steel beams, or monolithic concrete beams having a total depth
not less than about 3 times the slab thickness. While it was not a part of the 1977
or later ACI Codes, its continued use is permissible under the ACI 318-95 code
provision (13.5.1) that a slab system may be designed by any procedure satisfying
conditions of equilibrium and geometric compatibility, if it is shown that the
design strength at every section is at least equal to the requires strength, and that
serviceability requirements are met.
The method makes use of tables pf moment coefficients for a variety of
conditions. These coefficients are based on elastic analysis but also account for
inelastic redistribution. In consequence, the design moment in either direction is
smaller by an appropriate amount than the elastic maximum moment in that

Prof. Dr. Qaisar Ali (qaisarali.onlineuet.com) Page 5 of 18


Department of Civil Engineering N-W.F.P UET Peshawar Design of Concrete Structures (CE-405)

direction. The moments in the middle strip in the two directions are computed
from:
Ma = Cawla2
And Mb = Cbwlb2
Where Ca, Cb = tabulated moment coefficients
w = uniform load, psf
la, lb = length of clear spans in short and long directions respectively.

Therefore, for the design problem under discussion,


m = la/lb
= 12/16 = 0.75
la = 12'

Case 6
lb = 16'

Figure 1.3: Two way slab (S2)

Table 1.2: Moment coefficients for slab


Case # 6 [m = 0.75]

Coefficients for negative Coefficients for dead load Coefficients for live load
moments in slabs positive moments in slabs positive moments in slabs

Ca,neg Cb,neg Ca,dI Cb,dl Ca,ll Cb,ll


0.088 0 0.048 0.012 0.055 0.016
Refer to tables 12.3 to 12.6, of Nilson 12th Ed.

Ma, neg = Ca, neg x wu x la2


= 0.088 x 0.211 x 122 = 2.67 ft-k = 32.04 in-k
Mb, neg = Cb, neg x wu x lb2
= 0 x 0.211 x 162 = 0 ft-k
M a, pos, dl = C a, pos, dl x wu, dl x la2

Prof. Dr. Qaisar Ali (qaisarali.onlineuet.com) Page 6 of 18


Department of Civil Engineering N-W.F.P UET Peshawar Design of Concrete Structures (CE-405)

= 0.048 x 0.147 x 122 = 1.016 ft-k = 12.19 in-k


M b, pos, dl = C b, pos, dl x wu, dl x lb2
= 0.012 x 0.147 x 162 = 0.45 ft-k = 5.42 in-k
M a, pos, ll = C a, pos, ll x wu, ll x la2
= 0.055 x 0.064 x 122 = 0.51 ft-k = 6.12 in-k
M b, pos, ll = C b, pos, ll x wu, ll x lb2
= 0.016 x 0.064 x 162 = 0.262 ft-k = 3.144 in-k
Therefore, finally we have,
Ma, neg = 2.67 ft-k = 32.04 in-k
Mb, neg = 0 ft-k
Ma, pos, (dl + ll) = 1.016 + 0.51 = 1.53 ft-k = 18.36 in-k
Mb, pos, (dl + ll) = 0.45 + 0.262 = 0.712 ft-k = 8.544 in-k

Step No 4: Design.
Asmin = 0.002bhf = 0.002 x 12 x 5 = 0.12 in2
a = Asminfy/ (0.85fc′b)
= 0.12 x 40/ (0.85 x 3 x 12) = 0.156 in
Φ Mn(min) = ΦAsminfy (d – a/2)
= 0.9x 0.12 x 40 x (4-0.156/2) = 16.94 in-k (capacity provided by Asmin).
Φ Mn(min) is greater than Mb, pos, (dl + ll) but less than Ma, neg and Ma, pos, (dl + ll).
M b, pos, (dl + ll) = 0.712 ft-k = 8.544 in-k < Φ Mn(min)
Therefore, Asmin = 0.12 in2 governs.
Using 3/8″ Φ (#3) {#10, 10 mm}, with bar area Ab = 0.11 in2
Spacing = (0.11/0.12) x 12 = 11″
Maximum spacing according to ACI 13.3.2 for two way slab is:
2hf = 2 x 5 =10″
Therefore maximum spacing of 10″ governs.
Finally use #3 @ 9″ c/c (#10 @ 225 mm c/c).
“Provide #3 @ 9″ c/c as negative reinforcement along the longer direction.”

M a, pos, (dl + ll) = 1.53 ft-k = 18.36 in-k > Φ Mn


Let a = 0.2d = 0.2 x 4 = 0.8 in
As = 1.53 x 12/ {0.9 x 40 x (4 – (0.8/2))} = 0.146 in2

Prof. Dr. Qaisar Ali (qaisarali.onlineuet.com) Page 7 of 18


Department of Civil Engineering N-W.F.P UET Peshawar Design of Concrete Structures (CE-405)

a = 0.146 x 40/ (0.85 x 3 x 12) = 0.191 in


As = 1.53 x 12/ {0.9 x 40 x (4 – 0.191/2)} = 0.131 in2
a = 0.131 x 40/ (0.85 x 3 x 12) = 0.171 in
As = 1.53 x 12/ {0.9 x 40 x (4 – 0.30/2)} = 0.131 in2, O.K
Using 3/8″ Φ (#3) {#10, 10 mm}, with bar area Ab = 0.11 in2
Spacing = 0.11 x 12/0.131 = 10.07″ ≈ 9″ c/c
Finally use #3 @ 9″ c/c (#10 @ 225 mm c/c).

Ma, neg = 2.67 ft-k = 32.04 in-k


Let a = 0.2d = 0.2 x 4 = 0.8 in
As = 2.67 x 12/ {0.9 x 40 x (4 – (0.8/2))} = 0.24 in2
a = 0.24 x 40/ (0.85 x 3 x 12) = 0.31 in
As = 2.67 x 12/ {0.9 x 40 x (4 – 0.31/2)} = 0.23 in2
a = 0.23 x 40/ (0.85 x 3 x 12) = 0.30 in
As = 2.67 x 12/ {0.9 x 40 x (4 – 0.30/2)} = 0.23 in2, O.K.
Using 3/8″ Φ (#3) {#10, 10 mm}, with bar area Ab = 0.11 in2
Spacing = 0.11 x 12/0.23 = 5.7″ ≈ 4.5″ c/c
Finally use #3 @ 4.5″ c/c (#10 @ 110 mm c/c).

(3) BEAM DESIGN (2 span, continuous):


Data Given:
Exterior supports = 9″ brick masonry wall.
fc′ = 3 ksi
fy = 40 ksi
Column dimensions = 12″ x 12″
Step No 1: Sizes.
According to ACI 9.5.2.1, table 9.5 (a):
Minimum thickness of beam with one end continuous = hmin = l/18.5
l = clear span (ln) + depth of member (beam) ≤ c/c distance between supports
[ACI 8.7].

Prof. Dr. Qaisar Ali (qaisarali.onlineuet.com) Page 8 of 18


Department of Civil Engineering N-W.F.P UET Peshawar Design of Concrete Structures (CE-405)

Table 1.3: Clear Spans of beam.


Case Clear span (ln)
End span (one end continuous) 12.375 – (12/12)/2 = 11.875′

Let depth of beam = 18″


ln + depth of beam = 11.875′ + (18/12) = 13.375′
c/c distance between beam supports = 12.375 + (4.5/12) = 12.75′
Therefore l = 12.75′
Depth (h) = (12.75/18.5) x (0.4 + 40000/100000) x 12
= 6.62″ (Minimum requirement of ACI 9.5.2.1).
Take h = 1.5′ = 18″
d = h – 3 = 15″

9" Brick masonry wall 12" x 12" RCC Column

12.375' 12.375'
l n = 12.375 - 12/12 = 11.875' ln = 12.375 - 12/12 = 11.875'
Figure 1.4: c/c distance & clear span of Beam.

Step No 2: Loads.
Service Dead Load (D.L) = 0.0625 + 0.04 + 0.02 = 0.1225 ksf (Table 1.1)
Service Live Load (L.L) = 40 psf or 0.04 ksf
Beam is supporting 5' slab. Therefore load per running foot will be as follows:
Service Dead Load from slab = 0.1225 x 5 = 0.6125 k/ft
Service Dead Load from beam’s self weight = hwbwγc
= (13 x 12/144) x 0.15 = 0.1625 k/ft
Total Dead Load = 0.6125 + 0.1625 = 0.775 k/ft
Service Live Load = 0.04 x 5 = 0.2 k/ft
wu = 1.2D.L + 1.6L.L = 1.2 x 0.775 + 1.6 x 0.20 = 1.25 k/ft

Prof. Dr. Qaisar Ali (qaisarali.onlineuet.com) Page 9 of 18


Department of Civil Engineering N-W.F.P UET Peshawar Design of Concrete Structures (CE-405)

Step No 3: Analysis.
Refer to ACI 8.3.3 or page 396, Nelson 13th Ed, for ACI moment and shear
coefficients.
1) AT INTERIOR SUPPORT:
Negative moment (Mneg) = Coefficient x (wuln2)
= (1/9) x {1.25 x (11.875)2}
= 19.59 ft-k = 235.08 in-k
2) AT MID SPAN:
Positive moment (Mpos) = Coefficient x (wuln2)
= (1/11) x {1.25 x (11.875)2}
= 16.02 ft-k = 192.24 in-k
Vint = 1.15wuln/2 = 1.15 x 1.25 x 11.875/2 = 8.54 k
Vu(int) = 8.54 – 1.25 x 1.25 = 6.97 k
Vext = wuln/2 = 1.25 x 11.875/2 = 7.42 k
Vu(ext) = 7.42 – 1.25 x 1.25 = 5.86 k
wu = 1.25 k/ft

ln = 11.875' ln = 11.875'

wu ln /2 1.15wu ln /2
ACI Shear
1.15wu ln /2 wu ln /2 Coefficients

Vu (ext) = 5.86 k

7.42 k

d = 1.25'
8.54 k
Vu(int) = 6.97 k

1/ 11 1/ 11 ACI Moment
0 0 Coefficients
1/ 9 1/ 9

192.24 in-k 192.24 in-k

235.08 in-k

Figure 1.5: Approximate shear force and bending moment diagrams.

Prof. Dr. Qaisar Ali (qaisarali.onlineuet.com) Page 10 of 18


Department of Civil Engineering N-W.F.P UET Peshawar Design of Concrete Structures (CE-405)

Step No 4: Design.
(A) Flexural Design:
(1) For Positive Moment:
Step (a): According to ACI 8.10, beff for L-beam is minimum of:
(i) 6hf + bw = 6 x 5 + 12= 42″
(ii) bw + Span length of beam/12 = 12 + (12.75 x 12) /12 = 24.75″
(iii)Clear distance to the next web = Not Applicable
So beff = 24.75″
Step (b): Check if beam is to be designed as rectangular beam or L-beam.
(i). Assume a = hf = 5″
As = Mu/ {Φfy (d – a/2)}
As = 192.24/ {0.9 x 40 x (15-5/2)} = 0.427 in2
(ii).Re-calculate “a”:
a = Asfy/ (0.85fc′beff)
a = 0.427 x 40/ (0.85 x 3 x 24.75) = 0.271″ <hf
Therefore design beam as rectangular.
Trial #1:
As = 192.24/ {0.9 x 40 x (15 – 0.271/2)} = 0.359 in2
a = 0.359 x 40/ (0.85 x 3 x 24.75) = 0.228″
Trial #2:
As =192.24/ {0.9 x 40 x (15 – 0.228/2)} = 0.358 in2, O.K.
Step (c): Check for maximum and minimum reinforcement.
Asmax = ρmaxbwd
ρmax = 0.85 x 0.85 x (3/40) x {0.003/(0.003 + 0.005)} = 0.0203
Asmax = 0.0203 x 12 x 15 = 3.654 in2
Asmin = ρminbwd
Asmin = 0.005 x 12 x 15 = 0.9 in2
As = 0.358 in2 < Asmin, so Asmin governs.
Using 5/8″ Φ (#5) {#16, 16 mm}, with bar area Ab = 0.31 in2
No. of bars = As/Ab
= 0.90/0.31 = 2.90 ≈ 3 bars
Use 4 #5 bars {4 # 16 bars, 16 mm}.

Prof. Dr. Qaisar Ali (qaisarali.onlineuet.com) Page 11 of 18


Department of Civil Engineering N-W.F.P UET Peshawar Design of Concrete Structures (CE-405)

(2) For Interior Negative Moment:


Step (a): Now we take bw = 12″ instead of beff for calculation of “a” because of
flange in tension.

Mu = 235.08 in-k
bw = 12″
h = 18″
d = 15″
(i) Trial #1:
As =Mu/ {Φfy (d – a/2)}
Let a = 0.2d
As =235.08 / [0.9 x 40 x {15-(0.2 x 15)/2)}] = 0.484 in2
a = 0.484 x 40/ (0.85 x 3 x 12) = 0.632″
(ii) Trial #2:
As = 235.08/ {0.9 x 40 x (15 – 0.632/2)} = 0.44 in2
a = 0.44 x 40/ (0.85 x 3 x 12) = 0.58″
(iii)Trial #3:
As = 235.08/ {0.9 x 40 x (15 – 0.58/2)} = 0.44 in2 <Asmin
So Asmin governs.
Using 5/8″ Φ (#5) {#16, 16 mm}, with bar area Ab = 0.31 in2
No. of bars = As/Ab
= 0.90/0.31 = 2.90 ≈ 3 bars
Use 4 #5 bars {4 # 16 bars, 16 mm}.

(B) Shear Design for beam:


Step (a):
d = 15″ = 1.25′
Vu (ext) = 5.86 k
Vu (int) = 6.97 k
Step (b):
ΦVc = Φ2√ (fc′)bwd
= {0.75 x 2 x √ (3000) x 12 x 15}/1000 = 14.78 k > Vu (ext) & Vu (int).
Theoretically, no shear reinforcement is required, but minimum will be provided.

Prof. Dr. Qaisar Ali (qaisarali.onlineuet.com) Page 12 of 18


Department of Civil Engineering N-W.F.P UET Peshawar Design of Concrete Structures (CE-405)

Maximum spacing (smax) permitted by ACI 11.5.4 shall be minimum of:


(i) Avfy/(50bw) = 0.22 x 40000/(50 x 12) =14.67″ c/c
(ii) d/2 =15/2 =7.5″ c/c
(iii)24″ c/c
Other checks:
(a) Check for depth of beam {ACI 11.5.6.9}:
ΦVs ≤ Φ8√ (fc′)bwd
Φ8√ (fc′)bwd = 0.75 x 8 x √ (3000) x 12 x 15/1000
= 59.14 k
ΦVs = (ΦAvfyd)/sd
= (0.75 x 0.22 x 40 x 15)/7.5 = 13.2 k < 82.8 k, O.K.
So depth is O.K. If not, increase depth of beam.
(b) Check for spacing given under “maximum spacing requirement of ACI":
ΦVs ≤ Φ4√ (fc′)bwd. {ACI 11.5.4.3}
Φ4√ (fc´)bwd = 0.75 x 4 x √ (3000) x 12 x 15/1000
= 29.57 k
ΦVs = (ΦAvfyd)/sd
= (0.75 x 0.22 x 40 x 21)/7.5 = 13.2 k < 29.57 k, O.K.
Therefore spacing given under “maximum spacing requirement of ACI" is
O.K. Otherwise reduce spacing by half.
Provide # 3, 2 legged @ 7.5″ c/c {#10, 2 legged stirrups @ 190 mm c/c}
throughout, starting at sd/2 = 7.5/2 = 3.75″ from the face of the support.

(4) DESIGN OF COLUMN:


i) Load on column:
Pu = 2Vint = 2 x 8.54 = 17.08 k (Reaction at interior support of beam)
Gross area of column cross-section (Ag) = 12 x 12 =144 in2
fc′ = 3 ksi
fy = 40 ksi
ii) Design:
Nominal strength (ΦPn) of axially loaded column is:
ΦPn = 0.80Φ {0.85fc′ (Ag – Ast) + Astfy} {for tied column, ACI 10.3.6}

Prof. Dr. Qaisar Ali (qaisarali.onlineuet.com) Page 13 of 18


Department of Civil Engineering N-W.F.P UET Peshawar Design of Concrete Structures (CE-405)

Let Ast = 1% of Ag (Ast is the main steel reinforcement area)


ΦPn = 0.80 x 0.65 x {0.85 x 3 x (144 – 0.01 x 144) + 0.01 x 144 x 40}
= 218.98 k > (Pu = 17.08 k), O.K.
Ast =0.01 x 144 =1.44 in2
Using 3/4″ Φ (#6) {# 19, 19 mm}, with bar area Ab =0.44 in2
No. of bars = As/Ab
= 1.44/0.44 = 3.27 ≈ 4 bars
Use 4 #6 bars {4 #19 bars, 19 mm}.

Tie bars:
Using 3/8″ Φ (#3) {#10, 10 mm} tie bars for 3/4″ Φ (#6) {#19, 19 mm} main bars
(ACI 7.10.5),
Spacing for Tie bars according to ACI 7.10.5.1 is minimum of:
(a) 16 x dia of main bar =16 x 3/4 =12″ c/c
(b) 48 x dia of tie bar = 48 x (3/8) =18″ c/c
(c) Least column dimension =12″ c/c
Finally use #3, tie bars @ 9″ c/c (#10, tie bars @ 300 mm c/c).

Prof. Dr. Qaisar Ali (qaisarali.onlineuet.com) Page 14 of 18


Department of Civil Engineering N-W.F.P UET Peshawar Design of Concrete Structures (CE-405)

(5) Drafting:
(A) Slab “S1” and “S2”:

B
A A
MT2 MT2
MT1 MT2
MT2

M1 M1

M1 M1

S1 12' x 16' MT2 S1 12' x 16' MT2

M1 MT2

S2 8' wide MT2


M2
B1 B1

C1
B

Depth Bottom
Panel (in) Mark Reinforcement Mark Top reinforcement
3/8" φ @ 4.5" c/c Non continuous End
M1 3/8" φ @ 9" c/c MT1
3/8" φ @ 4.5" c/c Continouos End
S1 5"
M1 3/8" φ @ 9" c/c MT2 3/8" φ @ 9" c/c Non continuous Ends

M2 3/8" φ @ 6" c/c


S2 5" MT2 3/8" φ @ 9" c/c Non Continuous End
M1 3/8" φ @ 9" c/c

Prof. Dr. Qaisar Ali (qaisarali.onlineuet.com) Page 15 of 18


Department of Civil Engineering, N-W.F.P UET Peshawar Design of Concrete Structures (CE-405)

#3 @ 9" c/c
#3 @ 9" c/c #3 @ 6" c/c #3 @ 4.5" c/c
L1/4 = 3'-0" L1/3 = 4'-0"
h = 5"

#3 @ 9" c/c

L1 = 12'-0"

SECTION A-A
1.5" Expansion Joint
#3 @ 4.5" c/c #3 @ 9" c/c
#3 @ 9" c/c #3 @ 9" c/c
#3 @ 9" c/c
L2/4 = 4'-0" L2/4 = 4'-0" L/4=2'-0" L/4=2'-0"

12" x 18" Beam

#3 @ 9" c/c #3 @ 9" c/c

13 12" Brick Masonary Wall


L 2= 16'-0" L = 8'-0"

SECTION B-B

Prof. Dr. Qaisar Ali (qaisarali.onlineuet.com) Page 16 of 18


Department of Civil Engineering, N-W.F.P UET Peshawar Design of Concrete Structures (CE-405)

(B) Beam:
2 #5 Bars
A B B
A
0.33L = 4'-0" 0.33L = 4'-0"

4 #5 Bars #3, 2 legged stirrups @ 7.5" c/c

A B B A
4 #5 Bars 4 #5 Bars
s /2=3.75"

L = 11'-10.5" L = 11'-10.5"

BEAM DETAIL
Notes: -
(1) Use graph A.3, Nelson 13th Ed for location of cut off for continuous beams..
(2) Use table A.7, Nelson 13th Ed for maximum number of bars as a single layer in beam stem.

2 #5 Bars 5" 4 #5 Bars 5"

#3,2 legged stirrups @ 7.5" c/c #3,2 legged stirrups @ 7.5" c/c
18" 18"
4 #5 Bars 4 #5 Bars

12" 12"

SECTION A-A SECTION B-B


Prof. Dr. Qaisar Ali (qaisarali.onlineuet.com) Page 17 of 18
Department of Civil Engineering N-W.F.P UET Peshawar Design of Concrete Structures (CE-405)

(C) Column:

#3 ties @ 9" c/c

4 #6 Bars

12"

4 #6 Bars

#3 Ties @ 9" c/c


12"

12"

Column (C1) Detail

Prof. Dr. Qaisar Ali (qaisarali.onlineuet.com) Page 18 of 18

You might also like