Turbo Charger
Turbo Charger
Belagavi – 560018
A Seminar Report
on
“FLOATING WINDMILLS”
Submitted in partial fulfillment of the requirements for the award of the degree of
BACHELOR OF ENGINEERING
IN
MECHANICAL ENGINEERING
Submitted by
LAKSHMI NARAYANAN P
(1CK14ME032)
Under the guidance of
Mr. MOHAN KUMAR.K.A, M.Tech.,
Assistant Professor,
Department of Mechanical Engineering
CBIT-Kolar
CERTIFICATE
This is to certify that the seminar entitled “FLOATING WINDMILLS” is a bonafide work
carried out by, LAKSHMI NARAYANAN P (1CK14ME032), in partial fulfillment of the
requirements for the award of BACHELOR OF ENGINEERING IN MECHANICAL
ENGINEERING of the Visvesvaraya Technological University, Belagavi during the year
2017-18. The report has been approved as it satisfies the academic requirements with respect
to seminar work prescribed by the VTU of the above mentioned degree.
i
ACKNOWLEDGEMENT
The completion of seminar presentation brings with it a sense of satisfaction, but it is never
complete without thanking the persons responsible for it successful completion.
It is with the profound feeling of gratitude i would like express my sincere thanks to my
institution C. BYREGOWDA INSTITUTE OF TECHNOLOGY, Kolar for providing
excellent infrastructure for successful completion of this seminar.
I wish to express a whole hearted thanks to our beloved Principal, Dr. K R SURESH, for
providing excellent infrastructure to pursue the work in the college.
My hearty thanks are also due towards our HOD, Dr. APRAMEYAN S whose timely support
and suggestions went a long in the completion of seminar.
My hearty thanks to our seminar coordinator Mr. SRINATH K T, Assistant Professor, whose
timely support and suggestion went a long in the completion of seminar.
I would like to thank all who directly or indirectly helped me in bringing out this seminar
report.
I would like to thank all the faculties of Department of Mechanical Engineering for providing
me with their valuable guidance at all stages of work.
I extend very hearty thanks to my parents, friends for all the moral support they provided during
the preparation of seminar.
LAKSHMI NARAYANAN P
(1CK14ME032)
ii
CONTENTS
Page no.
ABSTRACT i
ACKNOWLEDGEMENT ii
CONTENTS iii
LIST OF FIGURES v
CHAPTER 1: 1
1. INTRODUCTION
CHAPTER 2: 3
2. LITERATURE SURVEY
CHAPTER 3: 5
3. NEED FOR FLOATING WINDMILL
CHAPTER 4: 6
4. HISTORICAL BACKGROUND
CHAPTER 5: 7
5. DESIGN CONSIDERATION
CHAPTER 6: 9
6. ENERGY PRODUCTION FROM INDMILLS
CHAPTER 7: 10
7. ADVANTAGES & DISADVANTAGES OF
WINDMILLS
7.1 ADVANTAGES
7.2 DISADVANTAGES
CHAPTER 8: 11
8. WIND POWER USAGE
CHAPTER 9: 12
9. GROWTH TRENDS
CHAPTER 10: 13
10. ENVIRONMENTAL EFFECTS
iii
CHAPTER 11: 14
11.COST TRENDS WITH GROWTH
CHAPTER 12:
12. FLOATING WINDFARMS vs OIL AND GAS 16
RESERVOIRS
CHAPTER 13: 17
13.CONCLUSION
BIBLIOGRAPHY 18
iv
LIST OF FIGURFES
v
FLOATING WINDMILLS 2017-2018
CHAPTER 1
1: INTRODUCTION
A floating wind turbine is a wind turbine mounted on a floating structure that allows the
turbine to generate electricity in water depths where bottom-mounted towers are not feasible.
The wind can be stronger and steadier over water due to the absence of topographic features that
may disrupt wind flow. The electricity generated is sent to shore through undersea cables. The
initial capital cost offloading turbines is competitive with bottom-mounted, near-shore wind
turbines While the rate of energy generation is higher out in the sea as the wind flow is often
more steady and unobstructed by terrain features. The relocation of wind farms into the sea can
reduce visual pollution if the windmills are sited more than 12miles (19km) offshore, provide
better accommodation of fishing and shipping lanes, and allow sitting near heavily developed
coastal cities. Floating wind parks are wind farms that site several floating wind turbines closely
together to take advantage of common infrastructure such as power transmission facilities.
The tension-leg platform (TLP) supporting structure is a good choice for floating offshore
wind turbines because TLP has superior motion dynamics. This study investigates the effects of
TLP spoke dimensions on the motion of a floating offshore wind turbine system (FOWT). Spoke
dimension and offshore floating TLP were subjected to irregular wave and wind excitation to
evaluate the motion of the FOWT. This research has been divided into two parts: (1) Five models
were designed based on different spoke dimensions, and aero hydro servo-elastic coupled
analyses were conducted on the models using the finite element method. (2) Considering the
coupled effects of the dynamic response of a top wind turbine, a supporting-tower structure, a
mooring system, and two models on a reduced scale of 1: 80 were constructed and
experimentally tested under different conditions. Numerical and experimental results
demonstrate that the spoke dimensions have a significant effect on the motion of FOWT and the
experimental result that spoke dimension can reduce surge platform movement to improve
Turbine performance.
Offshore floating wind turbines represent the future of wind energy. However, significant
challenges must be overcome before these systems can be widely used. Because of the dynamics
of offshore floating wind turbines -- surge, sway, heave, roll, pitch, and yaw -- and the resulting
interactions between the rotor and generated wake, the aerodynamic analysis methods and design
codes that have found wide use throughout the wind energy industry may be inadequate.
Application of these techniques to offshore floating wind turbine aerodynamics may result in off-
optimal designs, effectively handicapping these next-generation systems, thereby minimizing
their full potential. This dissertation will demonstrate that the aerodynamics of offshore floating
wind turbines are sufficiently different from conventional offshore and onshore wind turbines,
warranting the use of higher fidelity analysis approaches. It will outline the development and
validation of a free vortex wake code, the Wake Induced Dynamics Simulator, or Winds, which
uses a more physically realistic Lagrangian approach to modeling complex rotor-wake
interactions.
Finally, results from Winds simulations of various offshore floating wind turbines under
different load conditions will be presented. The simulation results indicate that offshore floating
wind turbine aerodynamics are more complex than conventional offshore or onshore wind
turbines and require higher fidelity analysis approaches to model adequately. Additionally,
platform pitching modes appear to drive the most aerodynamically-significant motions, followed
by yawing modes. Momentum balance approaches are shown to be unable to accurately model
these dynamic systems, and the associated dynamic inflow methods respond to velocity changes
at the rotor incorrectly. Future offshore floating wind turbine designs should strive to either
minimize platform motions or be complementarily optimized, via higher fidelity aerodynamic
analysis techniques, to account for them. It is believed that this dissertation is the first in-depth
study of offshore floating wind turbine aerodynamics and the applicability of various analysis
methods.
CHAPTER 2
2: LITERATURE SURVEY
[1] Musial, W.; S. Butterfield, A. Boone (2003-11)."Feasibility of Floating Platform
Systems for Wind Turbines" NREL preprint(NREL) (NREL/CP-500-34874): 14.
"Due to its simple construction, the capital expenditure of the floating Sway system is
competitive to bottom mounted, near-shore wind towers; however, the average wind speeds far
off-shore are typically higher so more energy can be produced and the cost of energy is actually
reduced when compared with near-shore wind parks”.
The various, proposed conceptual designs for floating platforms used for floating wind
turbines are described and the working principles of these various floater concepts are outlined.
This is followed by an overview of the research work that has been undertaken pertaining to
floating wind turbine technology by several research institutes and the academic community. The
research work undertaken to date is reviewed categorically according to the proposed floater
concept (spar-buoy type, TLP type, semi-submersible type, pontoon type and others) as per
sections. Based on the research work undertaken thus far, recommendations for future work are
suggested.
[2] Mark Svenvold(2009-09-09)."The world's first floating wind turbine goes on line in
Norway". DailyFinance.com. Retrieved2009-10-20.
To solve this issue, floating foundation concepts, such as spar, semisubmersible, and tension-
leg platform (TLP) supporting structures, have been used. As an active research direction, the
TLP supporting structure concept for offshore wind turbines is an appropriate choice for
intermediate water depths because of its superior motion and dynamic features compared with
other floating concepts23456. With the developed the first TLP wind turbine supporting structure
in 2004.
The tension-leg platform (TLP) supporting structure is a good choice for floating offshore
wind turbines because TLP has superior motion dynamics. This study investigates the effects of
TLP spoke dimensions on the motion of a floating offshore wind turbine system (FOWT). Spoke
dimension and offshore floating TLP were subjected to irregular wave and wind excitation to
evaluate the motion of the FOWT. This research has been divided into two parts: (1) Five models
were designed based on different spoke dimensions, and aero hydro servo-elastic coupled
analyses were conducted on the models using the finite element method. (2) Considering the
coupled effects of the dynamic response of a top wind turbine, a supporting-tower structure, a
mooring system, and two models on a reduced scale of 1: 80 were constructed and
experimentally tested under different conditions. Numerical and experimental results
demonstrate that the spoke dimensions have a significant effect on the motion of FOWT and the
experimental result that spoke dimension can reduce surge platform movement to improve
Turbine performance.
[4] Union of Concerned Scientists (2003-07-15)."Farming the Wind :Wind Power and
Agriculture". Retrieved 2009-10-20.
Wind energy is one of the most environmentally friendly renewable energy sources that
are used to generate power. Global interest in wind energy has increased because of abun-dant
global shore wind resources. shore wind resources are distributed in areas within from coastlines
at water depths greater than. Studies show that foundations, such as monopolies, jackets, and
gravity, are note economic for shore wind turbines with depths greater than To solve this issue,
coating foundation concepts, such as spar, semisubmersible, and tension-leg platform
(TLP)supporting structures, have been used.
CHAPTER 3
A few hundred meters offshore, winds are twice as strong as on land in much of the
world. Offshore wind energy has huge potential, and floating wind turbines is a promising
technology. Such turbines are now being developed. They are meant to be used out at sea in
deepwater, and they do not need to be permanently moored to the ocean bed. DEEP SEA.
Criteria for location of an offshore wind farm is excellent wind conditions and suitable water
depth. The wind farm must be situated near a strong onshore power grid and near harbours and
shipyards
CHAPTER 4
4: HISTORICAL BACKGROUND
These were the first of what was to become the modern form of wind turbine .Small wind
turbines for lighting of isolated rural buildings were wide spread in the first part of the 20th
century. Larger units intended for connection to a distribution network were tried at several
locations including Balaklava USSR in 1931 and in a1.25megawatt(MW)experimental unit in
Vermont in 1941.The modern wind power industry began in 1979 with the serial production of
wind turbines by Danish manufacturers Kuriant, Vestas, Nordtank, and Bonus. These early
turbines were small by today's standards, with capacities of 20–30kW each. Since then, they
have increased greatly in size, with the Enercon E-126 capable of delivering up to 7 MW, while
wind turbine production has expanded to many countries
CHAPTER 5
5: DESIGN CONSIDERATION
1. Tensioned Moorings: These legs provide stability during tow-out, once legs submerged,
vessels has no stability, various possible solutions including buoyancy sacks and collars.
2. Ballast: Three lines at lower cost but may loss position, if one breaks buoy is inherently
stable. Ballast at base of spur provides stability, and stability can be adjusted.
3. Hydrostatic: The installation of this type system is based on buoyancy force. All the
various force like gravity, buoyancy are to be considered while the installation of the
hydrostatic floating wind mills.
CHAPTER 6
CHAPTER 7
ADVANTAGES & DISADVANTAGES OF
WINDMILLS
7.1 ADVANTAGES
1. Offshore wind speeds tend to be faster than on land. Small increases in wind speed yield large
increases in energy production: a turbine in a 15-mph wind can generate twice as much energy
as a turbine in a 12-mph wind. Faster wind speeds offshore mean much more energy can be
generated.
2. Offshore wind speeds tend to be steadier than on land. A steadier supply of wind means a more
reliable source of energy.
3. Many coastal areas have very high energy needs. Half of the United States’ population lives in
coastal areas, with concentrations in major coastal cities. Building offshore wind farms in these
areas can help to meet those energy needs from nearby sources.
4. Offshore wind farms have many of the same advantages as land-based wind farms – they
provide renewable energy; they do not consume water; they provide a domestic energy source;
they create jobs; and they do not emit environmental pollutants or greenhouse gases
7.2 DISADVANTAGES
1. Offshore wind farms can be expensive and difficult to build and maintain. In particular:
2. Wave action, and even very high winds, particularly during heavy storms or hurricanes, can
damage wind turbines.
3. The production and installation of power cables under the seafloor to transmit electricity back
to land can be very expensive.
4. Effects of offshore wind farms on marine animals and birds are not fully understood.
5. Offshore wind farms built within view of the coastline (up to 26 miles offshore, depending on
viewing conditions) may be unpopular among local residents, and may affect tourism and
property values.
CHAPTER 8
India ranks 5th in the world with a total wind power capacity of 10,925 MW in 2009, [1]
or 3% of all electricity produced in India. The World Wind Energy Conference in New Delhi in
November 2006 has given additional impetus to the Indian wind industry. [54] Muppandal
village in Tamil Nadu state, India , has several wind turbine farms in its vicinity, and is one of
the major wind energy harnessing centres in India led by majors like Suzlon ,Vestas ,Micon
among others.
U.S. was up 31.8% in February, 2007 from February, 2006. The average output of one
MW of wind power is equivalent to the average electricity consumption of about 250 American
households. According to the American Wind Energy Association , wind will generate enough
electricity in 2008 to power just over 1% (equivalent to 4.5 million households) of total
electricity in U.S., up from less than 0.1% in 1999. U.S. Department of Energy studies have
concluded wind harvested in the Great Plains states of Texas, Kansas, and North Dakota could
provide enough electricity to power the entire nation, and that offshore wind farms could do the
same job. In addition, the wind resource over and around the Great Lakes , recoverable with
currently available technology, could by itself provide 80% as much power as the U.S. and
Canada currently generate from non-renewable resources, with Michigan's share alone equating
to one third of current U.S. electricity demand.
CHAPTER 9
GROWTH TRENDS
Global Wind Energy Council (GWEC) figures show that 2007 recorded an increase of
installed capacity of 20GW taking the total installed wind energy capacity to 94 GW, up from
74GW in 2006. Despite constraints facing supply chains for wind turbines, the annual market for
wind continued to increase at an estimated rate of 37%, following32% growth in 2006. In terms
of economic value, the wind energy sector has become one of the important players in the energy
markets with the total value of new generating equipment installed in 2007reaching €25 billion,
or US$36 billion. Although the wind power industry will be impacted by the global financial
crisis in 2009 and 2010, a BTM Consult five year forecast upto 2013 projects substantial growth.
Over the past five years the average growth in new installations has been 27.6 percent each year.
In the forecast to 2013 the expected average annual growth rate is 15.7 percent. More than
200GW of new wind power capacity could come on line before the end of 2013. Wind power
market 24 penetration is expected to reach 3.35 percent by 2013 and 8 percent by 2018. Existing
generation capacity represents sunk costs and the decision to continue production will depend on
marginal costs going forward, not estimated average costs at project inception. For example, the
estimated cost of new wind power capacity may be lower than that for "new coal" (estimated
average costs for new generation capacity) but higher than for "old coal" (marginal cost of
production for existing capacity). Therefore, the choice to increase wind capacity will depend on
factors including the profile of existing generation capacity
CHAPTER 10
ENVIRONMENTAL EFFECTS
CHAPTER 11
COST TRENDS WITH GROWTH
Wind and hydroelectric power generation have negligible fuel costs and relatively low
maintenance costs. Wind power has a low marginal cost and a high proportion of capital cost.
The estimated average cost per unit incorporates the cost of construction of the turbine and 26
transmission facilities, borrowed funds, return to investors (including cost of risk), estimated
annual production, and other components, averaged over the projected useful life of the
equipment, which may be in excess of twenty years. Energy cost estimates are highly dependent
on these assumptions so published cost figures can differ substantially.
A British Wind Energy Association report gives an average generation cost of onshore
wind power of around 3.2 pence (between US 5 and 6 cents) per kW·h (2005). Cost per unit of
energy produced was estimated in 2006 to be comparable to the cost of new generating capacity
in the US for coal and natural gas: wind cost was estimated at $55.80 per MW·h, coal at
$53.10/MW·h and natural gas at $52.50. Other sources in various studies have estimated wind to
be more expensive than other sources (see Economics of new nuclear power plants Clean coal ,
and Carbon capture and storage). In 2004, wind energy cost a fifth of what it did in the 1980s,
and some expected that downward trend to continue as larger multi- megawatt turbines were
mass-produced. However, installed cost averaged €1,300 a kW in 2007, compared to €1,100 a
kW in 2005. Not as many facilities can produce large modern turbines and their towers and
foundations, so constraints develop in the supply of turbines resulting in higher costs. Research
from a wide variety of sources in various countries shows that support for wind power is
consistently 70–80% among the general public.
Global Wind Energy Council (GWEC) figures show that 2007 recorded an increase of
installed capacity of 20 GW, taking the total installed wind energy capacity to 94 GW, up from
74 GW in 2006. Despite constraints facing supply chains for wind turbines, the annual market
for wind continued to increase at an estimated rate of 37%, following 32% growth in 2006. In
terms of economic value, the wind energy 27 sector has become one of the important players in
the energy markets, with the total value of new generating equipment installed in 2007 reaching
€25 billion, or US$36 billion. Although the wind power industry will be impacted by the Global
financial crisis in 2009 and 2010, a BTM Consult five year forecast up to 2013 projects
substantial growth. Over the past five years the average growth in new installations has been
27.6 percent each year. In the forecast to 2013 the expected average annual growth rate is 15.7
percent. More than 200GW of new wind power capacity could come on line before the end of
2013. Wind power market penetration is expected to reach 3.35 percent by 2013 and 8 percent by
2018. Existing generation capacity represents sunk costs, and the decision to continue production
will depend on marginal costs going forward, not estimated average costs at project inception.
For example, the estimated cost of new wind power capacity may be lower than that for "new
coal" (estimated average costs for new generation capacity) but higher than for "old coal"
(marginal cost of production for existing capacity). Therefore, the choice to increase wind
capacity will depend on factors including the profile of existing generation capacity.
CHAPTER 12
2. 1 MW of Rated Wind Turbine Power @ 40% Capacity Factor ~ 9.6 MWh / Day ~ 6.4
Barrels of Oil / Day 28
3. Conversion Efficiency of Oil & Gas Engines / Turbines, Wind Turbines ~ 40-50%
4. 1 GW Wind Farm (30 year life) ~ 70 M Barrel Oil Field ~ 6,400 Barrels / Day
7. Investment Risk in Oil & Gas: Exploration Costs & Volatility of Oil & Gas Prices
CHAPTER 13
CONCLUSION
The rate of energy generation is higher out in the sea as the wind flow is often more
steady and unobstructed by terrain features. The relocation of wind farms into the sea can reduce
visual pollution if the windmills are sited more than 12miles (19km) offshore, provide better
accommodation of fishing and shipping lanes, and allow sitting near heavily developed coastal
cities. Floating wind parks are wind farms that site several floating wind turbines closely
together to take advantage of common infrastructure such as power transmission facilities.
Optimized Spar Buoy and TLP Wind Turbine Floaters. Low Responses – Use of Onshore Wind
Turbines, Hybrid Offshore Wind & Wave Farms 29, Optimal Control to Enhance Wind and
Wave Power Output. Design of Offshore Electric Grids, Attractive Economic Attributes, Project
Finance for Utility Scale Offshore Wind & Wave Farms.
BIBLIOGRAPHY
[2]. (WMV) sway movie. SWAY. Event occurs at 1m30s. Retrieve 2009-10-20. "Due to its
simple construction, the capital expenditure of the floating Sway system is
competitive to bottom mounted, near-shore wind towers; however, the average wind
speeds far off-shore are typically higher so more energy can be produced and the
cost of energy is actually reduced when compared with near-shore wind parks”.
[3]. Mark Svenvold(2009-09-09)."The world's first floating wind turbine goes on line in
Norway". DailyFinance.com. Retrieved2009-10-20.
[4]. Union of Concerned Scientists (2003-07-15)."Farming the Wind :Wind Power and
Agriculture". Retrieved 2009-10-20.
[6]. Mark Svenvold (2009-09-09)."The world's first floating wind turbine goes on line in
Norway".