Wheatstone Bridge

Wheatstone bridge
Wheatstone bridge circuit diagram. The unknown

resistance Rx is to be measured; resistances R1, R2
and R3 are known and R2 is adjustable. If the

measured voltage VG is 0, then R2/R1 = Rx/R3.
This article needs additional citations for
verification.
Learn more
A Wheatstone bridge is an electrical circuit

used to measure an unknown electrical
resistance by balancing two legs of a
bridge circuit, one leg of which includes
the unknown component. The primary
benefit of the circuit is its ability to provide
extremely accurate measurements (in
contrast with something like a simple
voltage divider).[1] Its operation is similar
to the original potentiometer.
The Wheatstone bridge was invented by

Samuel Hunter Christie in 1833 and
improved and popularized by Sir Charles
Wheatstone in 1843. One of the
Wheatstone bridge's initial uses was for
the purpose of soils analysis and
comparison.[2]
Operation
In the figure, is the fixed, yet unknown,
resistance to be measured.
and are resistors of known

resistance and the resistance of is
adjustable. The resistance is adjusted
until the bridge is "balanced" and no
current flows through the galvanometer .
At this point, the voltage between the two
midpoints (B and D) will be zero. Therefore
the ratio of the two resistances in the
known leg is equal to the ratio of
the two in the unknown leg . If the
bridge is unbalanced, the direction of the
current indicates whether is too high or
too low.
At the point of balance,
Detecting zero current with a

galvanometer can be done to extremely
high precision. Therefore, if and
are known to high precision, then can
be measured to high precision. Very small
changes in disrupt the balance and are
readily detected.
Alternatively, if and are known,

but is not adjustable, the voltage
difference across or current flow through
the meter can be used to calculate the
value of using Kirchhoff's circuit laws.
This setup is frequently used in strain
gauge and resistance thermometer
measurements, as it is usually faster to
read a voltage level off a meter than to
adjust a resistance to zero the voltage.
Derivation
Directions of currents arbitrarily assigned
First, Kirchhoff's first law is used to find

the currents in junctions B and D:
Then, Kirchhoff's second law is used for

finding the voltage in the loops ABD and
BCD:
When the bridge is balanced, then IG = 0,

so the second set of equations can be
rewritten as:
Then, equation (1) is divided by equation

(2) and the resulting equation is
rearranged, giving:
Due to: I3 = Ix and I1 = I2 being
proportional from Kirchhoff's First Law in
the above equation I3 I2 over I1 Ix cancel
out of the above equation. The desired
value of Rx is now known to be given as:
On the other hand, if the resistance of the

galvanometer is high enough that IG is
negligible, it is possible to compute Rx
from the three other resistor values and
the supply voltage (VS), or the supply
voltage from all four resistor values. To do
so, one has to work out the voltage from
each potential divider and subtract one
from the other. The equations for this are:
where VG is the voltage of node D relative

to node B.
Significance
The Wheatstone bridge illustrates the
concept of a difference measurement,
which can be extremely accurate.
Variations on the Wheatstone bridge can
be used to measure capacitance,
inductance, impedance and other
quantities, such as the amount of
combustible gases in a sample, with an
explosimeter. The Kelvin bridge was
specially adapted from the Wheatstone
bridge for measuring very low resistances.
In many cases, the significance of
measuring the unknown resistance is
related to measuring the impact of some
physical phenomenon (such as force,
temperature, pressure, etc.) which thereby
allows the use of Wheatstone bridge in
measuring those elements indirectly.
The concept was extended to alternating
current measurements by James Clerk
Maxwell in 1865 and further improved by
Alan Blumlein around 1926.
Modifications of the
fundamental bridge
Kelvin bridge
The Wheatstone bridge is the fundamental

bridge, but there are other modifications
that can be made to measure various
kinds of resistances when the
fundamental Wheatstone bridge is not
suitable. Some of the modifications are:
Carey Foster bridge, for measuring small

resistances
Kelvin bridge, for measuring small four-
terminal resistances
Maxwell bridge, and Wien bridge for
measuring reactive components.
See also
Diode bridge, product mixer - diode
bridges
Phantom circuit – a circuit using a
balanced bridge
Post Office Box
Potentiometer (measuring instrument)
Potential divider
Ohmmeter
Resistance thermometer
Strain gauge
References
1. "Circuits in Practice: The Wheatstone
Bridge, What It Does, and Why It Matters",
as discussed in this MIT ES.333 class
video
2. "The Genesis of the Wheatstone Bridge"
by Stig Ekelof discusses Christie's and
Wheatstone's contributions, and why the
bridge carries Wheatstone's name.
Published in "Engineering Science and
Education Journal", volume 10, no 1,
February 2001, pages 37–40.
External links
DC Metering Circuits chapter from
Lessons In Electric Circuits Vol 1 DC
free ebook and Lessons In Electric
Circuits series.
Test Set I-49
Retrieved from
"https://en.wikipedia.org/w/index.php?
title=Wheatstone_bridge&oldid=887973536"
Last edited 16 days ago by Sam-2727
Content is available under CC BY-SA 3.0 unless

otherwise noted.

Wheatstone Bridge - Wikipedia PDF

Uploaded by

Copyright:

Available Formats

Wheatstone Bridge - Wikipedia PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Wheatstone Bridge - Wikipedia PDF

Uploaded by

Copyright:

Available Formats

Wheatstone bridge circuit diagram. The unknown

and R3 are known and R2 is adjustable. If the

A Wheatstone bridge is an electrical circuit

The Wheatstone bridge was invented by

and are resistors of known

At the point of balance,

Detecting zero current with a

Alternatively, if and are known,

Directions of currents arbitrarily assigned

First, Kirchhoff's ﬁrst law is used to ﬁnd

Then, Kirchhoff's second law is used for

When the bridge is balanced, then IG = 0,

Then, equation (1) is divided by equation

On the other hand, if the resistance of the

where VG is the voltage of node D relative

The Wheatstone bridge is the fundamental

Carey Foster bridge, for measuring small

Last edited 16 days ago by Sam-2727

Content is available under CC BY-SA 3.0 unless

You might also like