Array Incidence Loss (IAM) : Fresnel's Laws

Array incidence loss (IAM) Page 1 of 2
Array incidence loss (IAM)

The incidence effect (the designated term is IAM, for "Incidence Angle Modifier") corresponds to the
decrease of the irradiance really reaching the PV cells's surface, with respect to irradiance under normal
incidence. This decrease is mainly due to reflexions on the glass cover, which increases with the incidence
angle.
The transmission loss is a general phenomenon, due to the reflexion and transmission of the sun's ray at
each material interface (air-glass, glass-EVA, EVA-cell), as well as some absorption in the glass. This
arises for any incidence ray. For normal incidence, the reflexion is of the order of 5%, and is included in the
measured STC performance. The IAM only concerns the angular dependency of this effect, i.e. it is
normalized to the transmission at perpendicular incidence (0° incidence angle).
PVsyst uses an IAM function, which describes the deficit of transmission as a function of the incidence
angle. This function is applied either to the beam component, and to the diffuse and albedo, using an
integral over all "seen" directions, supposing an isotropic distribution of the diffuse irradiance.
Fresnel's laws
In principle, this phenomenon obeys the Fresnel's Laws describing transmission and reflections at the
interface of two transparent materials of different refraction indexes n1 and n2.
This is a very general behavior, derived from the general Maxwell's equations describing all electric
phenomena. The Fresnel's laws are first applied to the air-glass interface, they describe the reflected ray
and the transmitted ray. For the transmitted ray, it is applied to the interface Glass-EVA, and so on.
These laws allow to calculate the light effectively reaching the cell's surface below the protective layer
(usually glass), as a function of the incidence angle.
Now you can add an anti-reflective coating on the top interface air-glass. This thin layer has a lower
refraction index than the glass, which limits the first reflexion.
Ashrae Parametrization
In practice, this IAM function is often approached by using the "ASHRAE" parametrization (proposed in the
years 80's by this American norm organism), depending on one only parameter bo:
FIAM = 1 - bo · (1/cos i - 1) where i = incidence angle on the plane.
For single-glazed thermal solar modules, the usually accepted value for bo is of the order of 0.1. But in a
PV module, the lower interface, in contact with the cell, presents a high refraction index and our specific
measurements on real crystalline modules actually indicate a value of bo = 0.05.
Default in PVsyst, front surface specification

Up to the version 6.66, the Ashrae parametrization was used as default in PVsyst, whatever the module
characteristics.
However since the version 6.67, PVsyst gives the opportunity of specifying the kind of glass interface
(Normal glass, Anti-reflective coating, structured glass or plastic).
mk:@MSITStore:C:\Program%20Files%20(x86)\PVsyst6.7.8\PVsyst6.chm::/iam_los... 22-03-2019
Array incidence loss (IAM) Page 2 of 2
And attributes a default model according to this specification:

- All old modules (already defined in the database) remain with the Ashrae parametrization.
- The new modules with "Normal glass" or "Plastic" will use the normal Fresnel calculation.
- The new modules with "AR coating" or "Textured glass" will use the Fresnel calculation with AR
coating.
The next figure shows the IAM function for these 3 models:
We observe that the Ashrae parametrization underestimates the IAM value at medium angles (30 to 60°)
and overestimates them over these values.
The effects on the full year simulation may be studied in detail using the "Detailed study" button in the
"Detailed losses" dialog.
They depend on the meteo data, the plane orientation, etc. As an example, a simulation in Geneva gave
- Fresnel Normal glass slightly lower than the ASHRAE (- 0.25%)
- Difference Fresnel AR coating and normal glass 0.75%.
Definition in the PV module

The IAM model is defined with the PV module parameters, page "Additional data > Customized IAM".
Here you should define the glass surface type, and PVsyst will attribute the corresponding IAM model.
If you want, you can also specify a customized IAM profile, according to your experimental data.
However for the the database, if a manufacturer wants to set his own IAM profile, we require a detailed
measurement report established by an independent laboratory. And we also require that this measurement
is performed indoor.
Use in the simulation

The IAM model used in the simulation is defined in the "Detailed Losses" part.
By default, PVsyst will take the values specified for the PV module (of each sub-array). But you can also
specify another profile for this present simulation. For example retrieve the default value for a module which
has been specified with a customized profile by the manufacturer.
NB: The "Detailed Losses" dialog has a button "Detailed Study", which provides a complete analysis and
helps understanding the IAM effects as function of the Irradiance angular distributions (beam, diffuse and
albedo).
mk:@MSITStore:C:\Program%20Files%20(x86)\PVsyst6.7.8\PVsyst6.chm::/iam_los... 22-03-2019

Array Incidence Loss (IAM) : Fresnel's Laws

Uploaded by

Copyright:

Available Formats

Array Incidence Loss (IAM) : Fresnel's Laws

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Array Incidence Loss (IAM) : Fresnel's Laws

Uploaded by

Copyright:

Available Formats

Array incidence loss (IAM) Page 1 of 2

Array incidence loss (IAM)

Default in PVsyst, front surface specification

And attributes a default model according to this specification:

Definition in the PV module

Use in the simulation

You might also like