Is - 2062
Is - 2062
Is - 2062
This Product Manual shall be used as reference material by all Regional/Branch Offices & licensees
to ensure coherence of practice and transparency in operation of certification under Scheme-I of
Bureau of Indian Standards (Conformity Assessment) Regulations, 2018 for various products. The
document may also be used by prospective applicants desirous of obtaining BIS certification
licence/certificate.
1. Product : IS 2062:2011
No. of amendments : 1
2. Sampling Guidelines
c) Sample Size : For mechanical test: 1 metre + Prepared test pieces for
impact test
For chemical test : 5 pieces of 50 mm length/50 g drilling
5. Possible tests in a day : Freedom from defects, Dimensions, Tensile test ,Bend test,
Impact (Charpy) Test ,Chemical Composition: By chemical
method -- C, S, Mn or By instrumental method –all required
elements.
Licence is granted to use Standard Mark as per IS 2062:2011 with the following scope:
Name of the product Hot Rolled Medium and High Tensile Structural Steel
GROUPING GUIDELINES
PAGE 1 OF 2
i) Hot Rolled Medium and High Tensile Structure steel according to IS 2062: 2011 are
designated as per the following:
Grade Quality
-----------------------------------
Designations
E250 A,BR,B0,C
E275
Higher Grade
E300 -------------->
E350 Higher Quality
E410
E450 A,BR
E550
E600 -------------->
E650 Higher Quality
ii) The following grouping based on type of product, shall be followed for considering grant of
licence/inclusion as per IS 2062:2011
Page 1 of 9
offered, another sample of grade E 410 of quality C is also to
be drawn for covering sections of grades E 250 to E 650
quality A, BR and grades E 250 to E 410 of Quality B0, C.
3 Bars : One sample of any size of bars shall be drawn for testing. On
testing of sample of Higher Grade and Highest Quality, all
(1)Round and Square Bars other Lower grades and higher to lower Quality of the Steel
bars alongside Higher Grade and Higher to lower Quality
shall be covered in scope of licence.
While considering grant of licence/inclusion of additional varieties, it shall be ensured that complete
manufacturing facilities, testing equipments for essential requirements and testing arrangement for
optional requirements are available with manufacturer.
Page 2 of 9
ANNEXURE B
TO PRODUCT MANUAL FOR
Hot Rolled Medium and High Tensile Structure steel
According to IS 2062:2011
Page 1 of 3
Major test equipment essentially required to test as per requirements of Indian Standard.
Sl. No. Test Equipment/Chemicals and Identification Tests Used in with Clause
Numbers (Where applicable) Reference
1. Vernier Callipers Cl.10& 15
2. Micrometer Cl. 10& 15
3. Steel Scale ,Try-square, Radius gauges, Filler Gauges, Cl. 10& 15
Depth gauges, Straight edges, MagneticV-block, Angle
Protector (combination set), Protector outside and inside
calliper, Carbon Paper
4. UTM Cl.10
(0-1000KN)
5. Steel Mandrels (for bend tests), Templates(for Bend test), Mandrels is required on the basis of
UTM attachments/clamps/vice/Magnifying glass thickness of the productsas given in
Table-2 as per Cl.11.1 to 11.3
6. Charpy Impact tester, Thermometer, Specimen Cl.12.1 to 12.4(only for BR,B0,C
Inspection(Profile projector/Go&No Go Gauges, dial Qualities)
stand, surface plate, Micrometer), Deep Freezer
7. Analytical balance (0-200g,Lc:0.1mg) Cl.8
8. Weigh M/c Cl.15
9. Steel tape Cl.15
10. Surface roughness Tester/profile Meter, Manual welding Cl.13
equipment & low hydrogen electrode 4 mm or 5 mm dia (For Y Groove Crack ability Test)(For
Basic coated low hydrogen electrode or Gas Metal Arc Grade E250C only,if specifically
Welding/submerged arc welding,Burner Wire brush or agreed to between the purchaser and
abrasive paper Rutile electrode E3 XXXXX as per IS the manufacturer/supplier)
814, Oven for baking electrode, Spacers more than 2
mm, Magnetic particle equipment with all attachments
and accessories, Grinding wheel / polishing wheel and
etching solutions, Metallurgical microscope
11. NDT equipments, Metallurgical microscope with all Cl.14-OTHER TESTS such as non-
attachments, Polishing wheel, etching solution. destructive testing ,grain size,
directionality, inclusion content.
(as per agreement between the
purchaser and the
manufacturer/supplier)
12. Instrumental methods Cl8.1,8.2 for C,S,P,Mn,Si,Al, Cu,
Spectrometer: atomic-absorption spectrometry, Microalloying and alloying
inductively coupled plasma atomic emission, elements content
inductively coupled plasma mass spectrometry
techniques, spark source optical emission
spectrometry.
Spectrophotometer Mn,S,P,Si
Page 3 of 9
13. Strohlein or Leco apparatus with all attachments cl.8.1, 8.2 –C& S
Barometer with chart, Hot plate, Muffle furnace, (chemical method, alternative to
Complete range of glass wares, measuring instrumental method)
cylinders, Desiccator, porcelain boats or ceramic
crucibles, Thermometer, Electronic Balance,
Distilled Water,Hot air oven, Oxygen - 99.5 percent
minimum purity,ether or acetoneStandard
Reference Material (NML) with certificate
Reagents for C: tin granules or pure iron fillings,
acidulated water/brine water, methyl red,caustic
potash
Page 4 of 9
Hydroxide,Acetic Acid, Potassium Iodide, Starch
Solution, Sodium Thiosulphate Solution,
Ammonium Bifluoride Solution
ashless paper pulp, paper pulp pad, hot plate, Ni content Cl8.1,8.2
dessicator, (chemical method, alternative to
instrumental method)
Note: The above is an indicative list for the purpose of guidance only
Page 5 of 9
ANNEXURE C
TO PRODUCT MANUAL FOR
Hot Rolled Medium and High Tensile Structure steel
According to IS 2062:2011
Page 1 of 4
LABORATORY - A laboratory shall be maintained which shall be suitably equipped (as per the
requirement given in column 2 of Table 1) and staffed, where different tests given in the specification
shall be carried out in accordance with the methods given in the specification.
1.1 The manufacturer shall prepare a calibration plan for the test equipments.
2. TEST RECORDS – The manufacturer shall maintain test records for the tests carried out to
establish conformity.
4. CONTROL UNIT – All structural steel hot rolled to same dimensions and form (Angle or Channel
or Flat or Round etc.), representing the same cast & grade designation, manufactured under uniform
conditions of production in a day in the same place.
5. LEVELS OF CONTROL - The tests as indicated in column 1 of Table 1 and the levels of control
in column 3 of Table 1, shall be carried out on the whole production of the factory which is covered
by this plan and appropriate records maintained in accordance with paragraph 2 above.
5.1 All the production which conforms to the Indian Standards and covered by the licence should be
marked with Standard Mark.
Page 6 of 9
ANNEXURE C
TO PRODUCT MANUAL FOR
Hot Rolled Medium and High Tensile Structure steel
According to IS 2062:2011
Page 2 of 4
Page 7 of 9
(see Note-3)
Note-2: The control unit and levels of control as decided by the Bureau are obligatory to which the
licensee shall comply with.
Note -3: No testing for product analysis is required if material fed to rolling mills is ISI marked and
received with test certificate
Page 8 of 9
ANNEXURE I BIS
STANDARD
Page 4 of 4 MARK
(Para 6 of the Scheme of Inspection and Testing)
XYZ IRON AND STEEL COMPANY
(Registered office Address and works address)
TEST CERTIFICATE FOR HOT ROLLEDMEDIUM AND HIGH TENSILE STRUCTURAL STEEL
Order Section Control Grade Quantity CHEMICAL COMPOSITION MECHANICAL PROPERTIES Optional
No. & (nom Unit & in tonnes Remark
Date Size) No. Quality s
C S P S Mn *Cu @Micro Al CE Tensile Elongatio Yield Bend Impact Crack
i Alloying strength n Stress test test ability
Elements test
% % % % % %
%
* For copper-bearing quality
@ Micro-alloying element present should be indicated
REMARKS
WAGON NO.
TRUCK NO. FOR XYZ IRON AND STEEL COMPANY
(It is suggested that size A4 paper be used for this test certificate)
Page 9 of 9