HT-E5400

5.1CH Blu-ray™
Home Entertainment System
user manual

imagine the possibilities

Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register

HT-E5400_ZA_0417-1(D2D).indd 1 2012-04-17 오후 6:44:47

 Safety Information
Warning
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN

The lighting flash and Arrowhead CAUTION: TO REDUCE THE RISK OF ELECTRIC The explanation point within the triangle
within the triangle is a warning sign SHOCK, DO NOT REMOVE COVER (OR BACK) is a warning sign alerting you of important
alerting you of dangerous voltage NO USER SERVICEABLE PARTS INSIDE. REFER instructions accompanying the product.
inside the product. SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING CLASS 1 LASER PRODUCT

• To reduce the risk of fire or electric shock, do This Compact Disc player is classified as a CLASS
not expose this appliance to rain or moisture. 1 LASER product. Use of controls, adjustments
or performance of procedures other than those
FCC NOTE (for U.S.A) specified herein may result in hazardous radiation
This equipment has been tested and found to exposure.
comply with the limits for a Class B digital device, Complies with 21CFR 1040.10 except for
pursuant to Part 15 of the FCC rules. These limits deviations pursuant to Laser Notice No. 50, dated
are designed to provide reasonable protection June 24, 2007.
against harmful interference in a residential
DANGER :
installation. This equipment generates, uses
and can radiate radio frequency energy and, if • VISIBLE AND INVISIBLE LASER RADIATION
not installed and used in accordance with the WHEN OPEN. AVOID DIRECT EXPOSURE TO
instructions, may cause harmful interference BEAM. (FDA 21 CFR)
to radio or television reception, which can be CAUTION :
determined by turning the equipment off and on. • CLASS 3B VISIBLE AND INVISIBLE LASER
The user is encouraged to try to correct the RADIATION WHEN OPEN. AVOID EXPOSURE
interference by one or more of the following measures.
TO THE BEAM (IEC 60825-1)
• Reorient or relocate the receiving antenna.
• THIS PRODUCT UTILIZES A LASER.
• Increase the separation between the equipment
USE OF CONTROLS OR ADJUSTMENTS
and receiver.
OR PERFORMANCE OF PROCEDURES
• Connect this equipment into an outlet on a
OTHER THAN THOSE SPECIFIED HEREIN
circuit different from that to which the receiver is
connected. MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE. DO NOT OPEN COVER AND DO
• Consult the dealer or an experienced radio/TV
technician for help. NOT REPAIR YOURSELF. REFER SERVICING
• This class B digital product meets all TO QUALIFIED PERSONNEL.
requirements of the Canadian Interference - CLASS 1 LASER PRODUCT
Causing Equipment Regulations.
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LÁSER CLASE 1

| 2 English

HT-E5400_ZA_0417-1(D2D).indd 2 2012-04-17 오후 6:45:11

 Precautions 13 . Unplug this apparatus during lightning storms
or when unused for long periods of time.
14 . Refer all servicing to qualified service

01
Important Safety Instructions
personnel. Servicing is required when the
Read these operating instructions carefully before

Safety Information
apparatus has been damaged in any way,
using the unit. Follow all the safety instructions such as when the power-supply cord or plug
listed below. is damaged, liquid has been spilled or objects
Keep these operating instructions handy for future have fallen into the apparatus, the apparatus
reference. has been exposed to rain or moisture, does
1 . Read these instructions. not operate normally, or has been dropped.
2 . Keep these instructions.
3 . Heed all warnings. Disc Storage & Management
4 . Follow all instructions. • Holding Discs
5 . Do not use this apparatus near water. - Fingerprints or scratches on
6 . Clean only with a dry cloth. a disc may reduce sound and
7 . Do not block any ventilation openings. Install picture quality or cause skipping.
in accordance with the manufacturer’s - Avoid touching the surface of a disc where
instructions. data has been recorded.
8 . Do not install near any heat sources such - Hold the disc by the edges so that fingerprints
as radiators, heat registers, stoves, or other will not get on the surface.
apparatus (including AV receivers) that - Do not stick paper or tape on the disc.
produce heat. • Cleaning Discs
9 . Do not defeat the safety purpose of the - If you get fingerprints or dirt on a
polarized or grounding-type plug. A polarized disc, clean it with a mild detergent
plug has two blades with one wider than the diluted in water and wipe with a
other. A grounding type plug has two blades soft cloth.
and a third grounding prong. The wide blade - When cleaning, wipe gently from the inside to
or the third prong are provided for your safety. the outside of the disc.
If the provided plug does not fit into your - Disc Storage
outlet, consult an electrician for replacement  Do not keep in direct sunlight.
of the obsolete outlet.
 Keep in a cool ventilated area.
10 . Protect the power cord from being walked on
or pinched particularly at plugs, convenience  Keep in a clean protection jacket and store
receptacles, and the point where it exits the vertically.
apparatus.
11 . Only use attachments/accessories specified Handling Cautions
by the manufacturer.
12 . Use only with the cart, • Do not expose this apparatus to dripping or
stand, tripod, bracket, splashing. Do not put objects filled with liquids,
or table specified by the such as vases, on the apparatus.
manufacturer, or sold with • To turn this apparatus off completely, you must
the apparatus. When a cart pull the power plug out of the wall socket.
is used, use caution when Consequently, the power plug must be easily
moving the cart/apparatus combination to and readily accessible at all times.
avoid injury from tip-over. • Do not touch the power plug with a wet hand.
It can cause an electric shock.

English 3|

HT-E5400_ZA_0417-1(D2D).indd 3 2012-04-17 오후 6:45:11

 Safety Information
• Do not plug multiple electric devices into the • Do not use the 3D Active Glasses for other
same wall socket. Ovedrloading a socket can purposes (such as general eyeglasses,
cause it to overheat, resulting in a fire. sunglasses, protective goggles, etc.)
• Maintenance of the Cabinet • Do not use the 3D function or 3D Active Glasses
- Before connecting other components to this while walking or moving around. Using the 3D
product, be sure to turn them off. function or 3D Active Glasses while moving
- If you move your product suddenly from a around may cause you to bump into objects,
cold place to a warm place, condensation trip, and/or fall, and cause serious injury.
may occur on the operating parts and lens • If you want to enjoy 3D content, connect a 3D
and cause abnormal disc playback. If this device (3D compliant AV receiver or TV) to the
occurs, unplug the product, wait for two product’s HDMI OUT port using a high-speed
hours, and then connect the plug to the HDMI cable. Put on 3D glasses before playing
power outlet. Then, insert the disc, and try to the 3D content.
play back again. • The product outputs 3D signals only through
• If the product makes an abnormal noise or HDMI cable connected to the HDMI OUT port.
produces a burning smell or smoke, turn off • As the video resolution in 3D play mode is fixed
the power switch immediately and disconnect according to the resolution of the original 3D
the power plug from the wall outlet. Then, video, you can not change the resolution to your
contact the nearest customer service center for preference.
technical assistance. Do not use the product. • Some functions such as BD Wise, screen size
Using the product as it is may cause a fire or an adjustment, and resolution adjustment may not
electric shock. operate properly in 3D play mode.
• To turn this apparatus off completely, you must • You must use a high-speed HDMI cable for
pull the power plug out of the wall socket. proper output of the 3D signal.
Consequently, the power plug must be easily • Stay at least three times the width of the screen
and readily accessible at all times. from the TV when watching 3D images. For
example, if you have a 46 inch screen, stay 138
inches (11.5 feet) from the screen.
Using the 3D Function
- Place the 3D video screen at eye level for the
IMPORTANT HEALTH AND SAFETY best 3D picture.
INFORMATION FOR 3D PICTURES. • When the product is connected to some 3D
Read and understand the following safety devices, the 3D effect may not function properly.
information before using the 3D function. • This product does not convert 2D content into
• Some viewers may experience discomfort while 3D.
viewing 3D TV such as dizziness, nausea, and • “Blu-ray 3D” and “Blu-ray 3D” logo are
headaches. trademarks of the Blu-ray Disc Association.
If you experience any such symptom, stop
viewing 3D TV, remove the 3D Active Glasses,
and rest. Copyright
• Watching 3D images for an extended period of
time may cause eye strain. If you feel eye strain, © 2012 Samsung Electronics Co.,Ltd.
stop viewing 3D TV, remove your 3D Active All rights reserved; No part or whole of this user’s
Glasses, and rest. manual may be reproduced or copied without the
• A responsible adult should frequently check on prior written permission of Samsung Electronics
children who are using the 3D function. Co.,Ltd.
If there are any reports of tired eyes, headaches,
dizziness, or nausea, have the child stop viewing
3D TV and rest.

| 4 English

HT-E5400_ZA_0417-1(D2D).indd 4 2012-04-17 오후 6:45:12

 License

01
• iPad, iPhone, iPod, iPod classic, iPod nano,

Safety Information
iPod shuffle, and iPod touch are trademarks
• Dolby and the double-D symbol are registered of Apple Inc., registered in the U.S. and other
trademarks of Dolby Laboratories. countries.
• This product uses Cinavia technology to
limit the use of unauthorized copies of some
commercially-produced film and videos and
• Manufactured under license under U.S. Patent their soundtracks. When a prohibited use of an
Nos: 5,956,674; 5,974,380; 6,226,616; unauthorized copy is detected, a message will
6,487,535; 7,392,195; 7,272,567; 7,333,929; be displayed and playback or copying will be
7,212,872 & other U.S. and worldwide patents interrupted.
issued & pending. DTS-HD, the Symbol, & DTS- More information about Cinavia technology
HD and the Symbol together are registered is provided at the Cinavia Online Consumer
trademarks & DTS-HD Master Audio | Essential Information Center at http://www.cinavia.com.
is a trademark of DTS, Inc. Product includes To request additional information about Cinavia
software. © DTS, Inc. All Rights Reserved. by mail, send a postcard with your mailing
address to: Cinavia Consumer Information
Center, P.O. Box 86851, San Diego, CA, 92138,
USA.”
• The terms HDMI and HDMI High-Definition This product incorporates proprietary technology
Multimedia Interface, and the HDMI Logo are under license from Verance Corporation and is
trademarks or registered trademarks of HDMI
protected by U.S. Patent 7,369,677 and other
Licensing LLC in the United States and other
U.S. and worldwide patents issued and pending
countries.
as well as copyright and trade secret protection
for certain aspects of such technology. Cinavia
is a trademark of Verance Corporation.
Copyright 2004-2010 Verance Corporation. All
rights reserved by Verance. Reverse engineering
or disassembly is prohibited.
• Oracle and Java are registered trademarks of • Open Source License Notice
Oracle and/or its affiliates. Other names may be
- In the case of using open source software,
trademarks of their respective owners.
Open Source Licenses are available on the
• This item incorporates copy protection product menu.
technology that is protected by U.S. patents
and other intellectual property rights of
Rovi Corporation. Reverse engineering and
disassembly are prohibited.
• Blu-ray Disc™, Blu-ray™, and the logos are
trademarks of Blu-ray Disc Association.

English 5|

HT-E5400_ZA_0417-1(D2D).indd 5 2012-04-17 오후 6:45:12

 Contents
SAFETY INFORMATION SETTINGS
2 Warning 23 The Initial Settings Procedure
3 Precautions 25 The Home Screen
3 Disc Storage & Management 25 Accessing the Settings Screen
3 Handling Cautions 26 Settings Menu Functions
4 Using the 3D Function 31 Networks and the Internet
4 Copyright 35 Upgrading Software
5 License
MEDIA PLAY
GETTING STARTED 37 The AllShare Play Screen
7 Disk and Format Compatibility 38 Playing Files on a USB Storage Device or
8 Logos of Discs the product can play iPod/iPhone
11 Accessories 38 iPod/iPhone Models You Can Use with
12 Front Panel This Product
12 Rear Panel 39 The Function Screen
13 Remote Control 39 Playing Commercial Video Discs
39 Playing Commercial Audio Discs
CONNECTIONS 40 Playing a Disc with User Recorded
Content
15 Connecting the Speakers 40 Using the AllShare Network Function
16 Speaker Components 42 Controlling Video Playback
16 Connecting The Speakers 44 Controlling Music Playback
17 Connecting the Optional Wireless 45 Playing Photo Contents
Receiver Module 46 Using the Tools Menu when a File is
18 Connecting the FM Antenna Highlighted
19 Connecting to an iPod/iPhone 48 Listening to Radio
19 Using a USB Cable 48 Using the Special Effects Remote Control
19 Using a Dock Buttons
19 Attaching the Toroidal Ferrite Core to the
Power Cord of the Main Unit NETWORK SERVICES
20 Connecting to a TV
50 Using Smart Hub
20 Method 1 Connecting to a TV
with an HDMI Cable - Best Quality 52 BD-LIVE™
(Recommended) 52 Using Disc to Digital
20 Method 2 Connecting to a TV with a
Video Cable - Good Quality
APPENDIX
21 Connecting to External Devices
21 Method 1 HDMI IN : Connecting to 53 Additional Information
an External Component with an HDMI 59 Troubleshooting
Cable 62 Specifications
21 Method 2 OPTICAL : Connecting an
External Digital Audio Component
21 Method 3 AUX IN : Connecting an
External Analog Component
22 Connecting to a Network Router
22 Wired Network
22 Wireless Network

| 6 English

HT-E5400_ZA_0417-1(D2D).indd 6 2012-04-17 오후 6:45:13

 Getting Started
Disk and Format Compatibility

02
Disc types and contents your product can play

Getting Started
Media Disc Type Details
Blu-ray Disc
BD-ROM or BD-RE/-R disc recorded in the BD-RE format.
3D Blu-ray Disc
VIDEO DVD-VIDEO, DVD-RW, DVD-VIDEO, recorded DVD+RW/DVD-RW(V)/DVDR/+R discs that have
DVD-R, DVD+RW, been recorded and finalized, or a USB storage media containing MKV, MP4
DVD+R contents.
CD-RW/-R, DVD-RW/-R, Music recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R discs or a USB storage
MUSIC
BD-RE/-R media containing MP3 or WMA contents.
CD-RW/-R, DVD-RW/-R, Photos recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R discs or a USB storage
PHOTO
BD-RE/-R media containing JPEG contents.

| NOTE |
 The product may not play certain CD-RW/-R and DVD-R because of the disc type or recording conditions.
 If a DVD-RW/-R disc has not been recorded properly in DVD video format, it will not be playable.
 Your product will not play content that has been recorded on a DVD-R at a bitrate that exceeds 10 Mbps.
 Your product will not play content that has been recorded on a BD-R or USB device at a bitrate that exceeds 30 Mbps.
 Playback may not work for some types of discs, or when you use specific operations, such as angle change and aspect ratio
adjustment. Information about the discs is written in detail on the disc box. Please refer to this if necessary.
 When you play a BD-J title, loading may take longer than a normal title or some functions may perform slowly.

Disc types your product cannot play

• HD DVD • DVD-RAM • DVD-RW(VR mode) • 3.9 GB DVD-R Disc

• DVD-ROM/PD/MV- • Super Audio CD • CVD/CD-ROM/CDV/ for Authoring.
Disc, etc (except CD layer) CD-G/CD-I/LD
(CD-Gs play audio
only, not graphics.)
| NOTE |
 This product may not respond to all operating commands because some Blu-ray Disc, DVD, and CD discs allow specific or
limited operation and provide only certain features during playback.
Please note that this is not a defect in the product.
 Samsung cannot guarantee that this product will play every disc bearing the Blu-ray Disc, DVD or CD logo because disc
formats evolve, and problems and errors may occur during the creation of Blu-ray Disc, DVD, and CD software and/or the
manufacture of discs.
 Please contact the SAMSUNG Customer Care Center at 1-800-726-7864 if you have questions or encounter difficulty when
playing Blu-ray Disc, DVD, or CD discs in this product. Also, refer to rest of this user manual for additional information on
playback restrictions.
 Some commercial discs and DVD discs purchased outside your region may not play on this product.

English 7|

HT-E5400_ZA_0417-1(D2D).indd 7 2012-04-17 오후 6:45:14

 Getting Started
Region Code Logos of Discs the product can play
Both products and discs are coded by region.
These regional codes must match for a disc to
play. If the codes do not match, the disc will not
play.
The Region Number for this product is displayed
on the rear panel of the product. Blu-ray Disc 3D Blu-ray Disc

Region
Disc Type Area
Code
North America, Central America,
South America, Korea, Japan,
A Taiwan, Hong Kong and South BD-LIVE Dolby
East Asia.

Blu-ray Disc Europe, Greenland, French

B territories, Middle East, Africa,
Australia and New Zealand.
NTSC broadcast system in
India, China, Russia, Central and DTS
C South Asia.
U.S.A, Canada, Korea, Japan

The U.S., U.S. territories and

1 Canada

Europe, Japan, the Middle East,

2 Egypt, South Africa, Greenland
Java
Taiwan, Korea, the Philippines,
3 Indonesia, Hong Kong
Supported Formats
Mexico, South America,
DVD-VIDEO
Central America, Australia, Music File Support
4 New Zealand, Pacific Islands,
Caribbean File Audio
Container Support Range
Extension Codec
Russia, Eastern Europe, India,
5 most of Africa, North Korea,
Mongolia
*.mp3 MP3 MP3 -

Compliant with
WMA version 10
6 China
* Sampling rates (in
kHz) - 8, 11, 16,
| NOTE | *.wma WMA WMA 22, 32, 44.1, 48
 If the Region number of a Blu-ray Disc/DVDs does not * Bitrates - All
correspond to the Region number of this product, the bitrates in the
product cannot play the disc. range 5kbps to
384kbps

| 8 English

HT-E5400_ZA_0417-1(D2D).indd 8 2012-04-17 오후 6:45:14

 Video File Support

Frame rate Bitrate

02
File Extension Container Video Codec Resolution Audio Codec
(fps) (Mbps)

Getting Started
H.264 BP/MP/HP 1920x1080 6 ~ 30 25 MP3
AC3
*.avi AVI
6 ~ 30 8 LPCM
MPEG4 SP/ASP 1920x1080 DTS Core
H.264 BP/MP/HP 1920x1080 6 ~ 30 25 MP3
AC3
*.mkv MKV
6 ~ 30 8 LPCM
MPEG4 SP/ASP 1920x1080 DTS Core
H.264 BP/MP/HP 1920x1080 6 ~ 30 25 MP3
AC3
*.asf ASF
6 ~ 30 8 LPCM
MPEG4 SP/ASP 1920x1080 WMA

*.wmv Window Media 6 ~ 30 25 WMA

WMV (wmv9) 1920x1080
Video v9
H.264 BP/MP/HP 1920x1080 6 ~ 30 25 MP3
*.mp4 MP4
6 ~ 30 8 AAC
MPEG4 SP/ASP 1920x1080
H.264 BP/MP/HP 1920x1080 6 ~ 30 25
*.3gp 3GPP AAC
MPEG4 SP/ASP 1920x1080 6 ~ 30 8
MPEG2 1920x1080 24/25/30 25 AC3
*.vro VRO MPEG
VOB MPEG1 1920x1080 24/25/30 25 LPCM
MPEG1 1920x1080 24/25/30 25 AC3
*.mpg 24/25/30 25 MPEG
*.mpeg PS MPEG2 1920x1080 LPCM
H.264 1920x1080 6 ~ 30 25 AAC

MPEG2 1920x1080 24/25/30 25 AC3

*.ts
*.tp AAC
TS H.264 1920x1080 6 ~ 30 25
*.trp MP3
VC1 1920x1080 6 ~ 30 25 DD+

 Limitations
- Even when a file is encoded by a supported codec listed above, the file might not be played if its
content has a problem.
- Normal playback is not guaranteed if the file’s container information is wrong or the file itself is
corrupted.
- Files having higher bit or frame rates than standard may stutter when played back.

English 9|

HT-E5400_ZA_0417-1(D2D).indd 9 2012-04-17 오후 6:45:15

 Getting Started
- The Seek (skip) function is not available if the • This product cannot play MP3 files with DRM
file’s index table is damaged. (Digital Rights Management) downloaded from
- When you playback a file remotely through a commercial sites.
network connection, video playback may stutter • Your product only supports video that is under
depending on the network speed. 30fps (frame rate).
 Video decoder • Your product only supports USB Mass Storage
Class (MSC) devices such as thumb drives and
- Supports up to H.264 Level 4.1 USB HDD. (HUB is not supported.)
- Does not support H.264 FMO/ASO/RS, VC1 • Certain USB HDD Devices, multi-card readers
SP/MP/AP L4 and AVCHD and thumb drives may not be compatible with
- MPEG4 SP, ASP : this product.
Below 1280 x 720 : 60 frames max • If some USB devices require excessive power,
Above 1280 x 720 : 30 frames max they may be limited by the circuit safety device.
- Does not support GMC 2 or higher • If playback from a USB HDD is unstable, provide
 Audio decoder addtional power by plugging the HDD into a wall
socket. If the problem continues, contact the
- Supports WMA 7, 8, 9 and STD USB HDD manufacturer.
- Does not support WMA 9 PRO multi-channel • You must remove the USB storage device safely
files if the number of channels is more than 2 or (by performing the “Safely Remove USB”
the files require lossless audio decoding. function) to prevent possible damage to the
- Does not support WMA sampling rate of USB memory.
22050Hz mono Press the HOME button to move to the home
menu, press the YELLOW (C) button, and then
Notes on the USB connection press the E button.
• SAMSUNG is not responsible for any data file
• Your product supports USB storage media, damage or data loss.
MP3 players, digital cameras, and USB card
readers.
• The product does not support folder or file AVCHD
names longer than 128 characters. (Advanced Video Codec High Definition)
• Some USB/digital camera devices may not be • This product can play back AVCHD format
compatible with the product. discs. These discs are normally recorded and
• Your product supports the FAT 16, FAT 32, and used in camcorders.
NTFS files systems. • The AVCHD format is a high definition digital
• Connect USB devices directly to the product’s video camera format.
USB port. Connecting through a USB cable • The MPEG-4 AVC/H.264 format compresses
may cause compatibility problems. images with greater efficiency than the
• Inserting more than one memory device into conventional image compressing format.
a multi-card reader may cause the reader to • Some AVCHD discs use the “x.v.Color” format.
operate improperly. This product can play back AVCHD discs that
• The product does not support the PTP protocol. use “x.v.Color” format.
• Do not disconnect a USB device during a • “x.v.Color” is a trademark of Sony Corporation.
“loading” process. • “AVCHD” and the AVCHD logo are trademarks
• The bigger the image resolution, the longer the of Matsushita Electronic Industrial Co., Ltd. and
image takes to display. Sony Corporation.

| 10 English

HT-E5400_ZA_0417-1(D2D).indd 10 2012-04-17 오후 6:45:16

 | NOTE |
 Some AVCHD format discs may not play, depending on the recording conditions.

02
 AVCHD format discs need to be finalized.
 “x.v.Color” offers a wider color range than normal DVD camcorder discs.

Getting Started
 Some MKV and MP4 format discs may not play, depending on their video resolution and frame rate.

Accessories
Check for the supplied accessories below.

FUNCTION
TV
SOURCE

RECEIVER SLEEP
BD TV

1 2 3
4 5 6
7 8 9
DISC MENU TITLE MENU

0 POPUP

MUTE

TUNING
VOL S/W LEVEL

Video Cable FM Antenna iPod Dock HOME

/ CH

REPEAT

(AH39-40001T) (AH42-00021A) (AH96-00051C) TOOLS INFO

RETURN EXIT

TUNER
MEMORY MO/ST
A B C D
SMART SEARCH 'ĺ' 3D SOUND
HUB
Disc2Digital PANDORA SUBTITLE SOUND

EFFECT

(For Power cord)

User Manual Toroidal Ferrite Core Remote Control (AH59-02402A)/

(AH68-02446A) (3301-000144) Batteries (AAA size) (4301-000116)

 Figures and illustrations in this User Manual are provided for reference only and may differ from actual
product appearance.

English 11 |

HT-E5400_ZA_0417-1(D2D).indd 11 2012-04-17 오후 6:45:16

 Getting Started
Front Panel
PLAY/PAUSE ENTER
STOP OPEN/CLOSE
FUNCTION VOLUME CONTROL

5V 500mA

DISC TRAY DISPLAY USB HOST POWER

REMOTE CONTROL
SENSOR

| NOTE |
 To upgrade the product's software through the USB Host jack, you must use a USB memory stick.
 When the product displays the Blu-ray Disc menu, you cannot start the movie by pressing the 6 button on the product or
the remote. To play the movie, you must select Play Movie or Start in the disc menu, and then press the E button.

Rear Panel

SPEAKERS OUT
AUX
IN
VIDEO
OUT FM ANTENNA
IMPEDANCE : 3

COOLING FAN SURROUND

SURROUND OPTICAL
DIGITAL
iPod LAN WIRELESS HDMI OUT 1 HDMI IN 2 FM ANT
AUDIO IN

iPod AUX IN VIDEO OUT

AUX VIDEO
SPEAKERS OUT
IN OUT
IMPEDANCE : 3

SURROUND

SURROUND OPTICAL
iPod LAN WIRELESS DIGITAL
HDMI OUT 1 HDMI IN 2
AUDIO IN
FM ANT

SPEAKER OUTPUT LAN TERMINAL HDMI OUT HDMI IN

CONNECTORS

TX CARD CONNECTION EXTERNAL DIGITAL

(WIRELESS) AUDIO IN (OPTICAL)

| NOTE |
 Ensure a minimum of 4 inches of clear space on all sides of the home theater to ensure adequate ventilation. Do not
obstruct the cooling fan or ventilation holes.

| 12 English

HT-E5400_ZA_0417-1(D2D).indd 12 2012-04-17 오후 6:45:19

 Remote Control

02
Tour of the Remote Control

Getting Started
Press to select Blu-ray's mode
(HDMI1, AUX, BD/DVD, etc.).
Turn the product on and off. FUNCTION or
TV
SOURCE
Press to select TV's video mode.
To change to TV mode, press the
TV button. Set a Sleep time to shut off the
RECEIVER SLEEP
product.
To change to Home Theater, BD TV
press the BD button. To open and close the disc tray.
1 2 3
Press numeric buttons to operate
options. 4 5 6
7 8 9
DISC MENU TITLE MENU Use to enter the Popup menu/
Press to view the disc menu. 0 POPUP Title menu.

Press to skip backwards or forwards. Press to search backwards or

forwards.
Press to stop/play a disc.
Press to pause a disc.
Cut off the sound temporarily. MUTE

Adjust the volume. TUNING Search for active FM stations and

VOL S/W LEVEL
/ CH
to change channels.
Press to use Netflix. Use to adjust the level of the
HOME REPEAT
subwoofer.
Press to move to the Home screen.
Allows you to repeat a title,
chapter, track or disc.
TOOLS INFO
Press to use the Tools menu.
Use to display the playback
Select on-screen menu items and information when playing
change menu value. a Blu-ray/DVD disc.
Press to exit the menu.
Return to the previous menu. RETURN EXIT

TUNER
Use to set a preset radio frequency.
MEMORY MO/ST
These buttons are used both for
menus on the product and also A B C D
Select MONO or STEREO for radio
several Blu-ray Disc functions. SMART SEARCH 'ĺ' 3D SOUND
broadcasts.
HUB
Press to use Smart Hub. Disc2Digital PANDORA SUBTITLE SOUND
Press to apply 3D sound effect.
EFFECT

Press to use Disc2Digital. Press to apply sound effects.

Press to search contents. Press to enjoy an ordinary 2D video
in 3D mode.

Press to use Pandora. Selects the disc subtitle language.

English 13 |

HT-E5400_ZA_0417-1(D2D).indd 13 2012-04-17 오후 6:45:20

 Getting Started
Installing batteries in the Remote TV Control Codes
Control Brand Code Brand Code
Admiral Mitsubishi/
56, 57, 58 18, 40, 59, 60, 75
Battery size: AAA (M.Wards) MGA
A Mark 01, 15 MTC 18
1 2 01, 02, 03, 04, 05, NEC 18, 19, 20, 40, 59, 60
Anam 06, 07, 08, 09, 10, 11, Nikei 03
12, 13, 14 Onking 03
AOC 01, 18, 40, 48 Onwa 03
Bell & Howell 06, 07, 08, 09, 54, 66,
57, 58, 81 Panasonic
(M.Wards) 67, 73, 74
Brocsonic 59, 60 Penney 18
Candle 18 03, 15, 17, 18, 48, 54,
Philco
Cetronic 03 59, 62, 69, 90
| NOTE | 15, 17, 18, 40, 48,
Citizen 03, 18, 25 Philips
 Make sure to match the “+” and “–” ends of the batteries 54, 62, 72
Cinema 97
Pioneer 63, 66, 80, 91
with the diagram inside the compartment. Classic 03
Portland 15, 18, 59
 Assuming typical TV usage, the batteries last for about Concerto 18
Proton 40
Contec 46
one year. Quasar 06, 66, 67
Coronado 15
Radio Shack 17, 48, 56, 60, 61, 75
 The remote control can be used up to approximately 23 Craig 03, 05, 61, 82, 83, 84
18, 59, 67, 76, 77, 78,
feet (7 meters) from the product in a straight line. Croslex 62 RCA/Proscan 92, 93, 94
Crown 03 Realistic 03, 19
Setting the Remote Control Curtis Mates 59, 61, 63 Sampo 40
CXC 03 00, 15, 16, 17, 40, 43,
You can control certain functions of your TV with
02, 03, 04, 15, 16, 17, Samsung 46, 47, 48, 49,
this remote control. 18, 19, 20, 21, 22, 23, 59, 60, 98
Daewoo 24, 25, 26, 27, 28,
29, 30, 32, 34, 35, 36, Sanyo 19, 61, 65
When operating a TV with the remote control 48, 59, 90 Scott 03, 40, 60, 61
Daytron 40 Sears 15, 18, 19
1 . Press the TV button to set the remote control
Dynasty 03 Sharp 15, 57, 64
to TV mode. 03, 15, 40, 46, 59, 61, Signature
Emerson
2 . Turn on your TV. 64, 82, 83, 84, 85 2000 57, 58
Fisher 19, 65 (M.Wards)
3 . While holding down the POWER button, Funai 03 Sony 50, 51, 52, 53, 55
enter the code corresponding to your brand Futuretech 03 Soundesign 03, 40
of TV. General 06, 40, 56, 59, 66, Spectricon 01
Electric (GE) 67, 68 SSS 18
• If there is more than one code listed for
Hall Mark 40
your TV in the table, enter one at a time to 18, 40, 48, 54, 59,
Hitachi 15, 18, 50, 59, 69 Sylvania 60, 62
determine which code works. Inkel 45 Symphonic 61, 95, 96
• Example : For a Samsung TV JC Penny 56, 59, 67, 86 Tatung 06
While holding down the POWER button, JVC 70 Techwood 18
use the number buttons to enter 00. If that KTV 59, 61, 87, 88 Teknika 03, 15, 18, 25
KEC 03, 15, 40 TMK 18, 40
does not work, try 15, then 16, etc.
KMC 15 Toshiba 19, 57, 63, 71
4 . If the TV turns off, the setting is complete. 01, 15, 16, 17, 37, Vidtech 18
LG (Goldstar) 38, 39, 40, 41, 42,
• You can use the TV POWER, VOLUME, 43, 44 Videch 59, 60, 69
CHANNEL, and Numeric buttons (0~9). Luxman 18 Wards 15, 17, 18, 40, 48,
54, 60, 64
19, 54, 56, 59, 60, 62,
LXI (Sears)
| NOTE | 63, 65, 71 Yamaha 18
15, 17, 18, 48, 54, 59, York 40
 The remote control may not work on some brands of TV's. Magnavox 60, 62, 72, 89
Yupiteru 03
Also, some operations may not be possible, depending on Marantz 40, 54
Zenith 58, 79
your brand of TV. Matsui 54
Zonda 01
 The remote control will work with Samsung TVs by MGA 18, 40
Dongyang 03, 54
default.

| 14 English

HT-E5400_ZA_0417-1(D2D).indd 14 2012-04-17 오후 6:45:22

 Connections
This section describes various methods of connecting the product to other external components.
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.

03
Connecting the Speakers

Connections
Position of the product
Place it on a stand or cabinet shelf, or
under the TV stand.
Subwoofer Center
Selecting the Listening Position
Front (R)
The listening position should be
Product Surround (R) located about 2.5 to 3 times the
distance of the TV's screen size
Front (L) away from the TV. For example, if
you have a 46 inch screen, locate
the listening position 115 to 138
Surround (L)
inches (9.6 to11.5 feet) from the
screen.

Place these speakers in front of your listening position, facing inwards (about 45°) toward
Front you. Place the front speakers so that their tweeters will be at the same height as your
Speakers ear. Align the front face of the front speakers with the front face of the center speaker or
place them slightly in front of the center speakers.

It is best to install the Center Speaker at the same height as the front speakers. You can
Center Speaker
also install it directly over or under the TV.

Place these speakers to the side of your listening position. If there isn't enough room,
place these speakers so they face each other. Position them about 2 to 3 feet (60 to
Surround 90cm) above your ear, facing slightly downward.
Speakers
* Unlike the front and center speakers, the surround speakers are used mainly for
sound effects. Sound will not come from them all the time.

Subwoofer The position of the subwoofer is not so critical. Place it anywhere you like.

English 15 |

HT-E5400_ZA_0417-1(D2D).indd 15 2012-04-17 오후 6:45:23

 Connections
Speaker Components

(L) (R) (L) (R)

SPEAKER CABLE

FRONT SURROUND CENTER SUBWOOFER

Connecting The Speakers

1. Match each speaker cable bundle to the correct speaker by matching the
color coded plug on each bundle to the colored sticker on the bottom of
each speaker.
2. To attach speaker wire to each speaker:
a. Press down the red tab on the back of the speaker, insert the red wire, Black Red
and then release the tab.
b. Press down the black tab on the back of the speaker, insert the black
wire, and then release the tab.
3. Connect the speaker wire plugs from each speaker to the back of the
k jjacks.
product by matching the colors of the speaker plugs to the colors of the speaker k

Front Speaker (L) Surround Speaker (L)

Center Speaker
SPEAKERS OUT
Surround
IMPEDANCE : 3

Speaker (R)
SURROUND

SURROUND

Front Speaker (R)

SPEAKERS OUT
IMPEDANCE : 3

SURROUND

Subwoofer SURROUND
iPod LAN WIRELESS HDM

| 16 English

HT-E5400_ZA_0417-1(D2D).indd 16 2012-04-17 오후 6:45:24

 Connecting the Optional Wireless Receiver Module
To connect the surround speakers wirelessly, you have to purchase the wireless receiver module and

03
TX card from your Samsung retailer.

Connections
• This product should be connected with the SWA-5000 only.

Center Speaker
SPEAKERS OUT Front
Speaker (L)

IMPEDANCE : 3
SURROUND

SURROUND

Front
Speaker (R)
SPEAKERS OUT

IMPEDANCE : 3
SURROUND

Subwoofer SURROUND
iPod LAN WIRELESS HDMI OUT

Surround Surround
Speaker (L) Speaker (R)

Wireless Receiver Module

1. Follow the 1 to 3 steps as shown on the previous page.

2. With the product turned off, insert the TX card into the TX Card
Connection (WIRELESS) on the back of the product.
• Hold the TX card so that the label "WIRELESS" faces upward and
insert the card into the port. LAN WIRELESS HDMI OUT

• The TX card enables communication between the product and the

wireless receiver module.
3. Connect the left and right surround speakers to the wireless receiver
module. Again, match the color of the plugs to the jacks on the
wireless receiver module. TX card
4. Plug the power cord of the wireless receiver module into the
wall outlet.
5. Turn on the product. The product and wireless receiver module will
now communicate with each other and you will hear sound from the Surround speakers.

English 17 |

HT-E5400_ZA_0417-1(D2D).indd 17 2012-04-17 오후 6:45:26

 Connections
| CAUTION |
 If you want to install the product on the wall, fasten the screws or nails on the wall firmly and use the holes on the rear of speaker to install.
However, when you install it, accessories (nails or screws) and installation is not provided by the company.
 Do not let children play with or near the speakers. They could get hurt if a speaker falls.
 When connecting the speaker wires to the speakers, make sure that the polarity (+/–) is correct.
 Keep the subwoofer speaker out of reach of children to prevent children from inserting their hands or alien substances into the duct (hole)
of the subwoofer speaker.
 Do not hang the subwoofer on the wall through the duct (hole).
 Do not insert any other card except the TX card dedicated to the product.
If you insert a different TX card, you can damage the product and may not be able to remove the card easily.
 Do not insert the TX card upside down or in the reverse direction.
 Insert the TX card when the product is turned off. Inserting the card when it is turned on may cause a problem.
 The wireless receiving antenna is built into the wireless receiver module. Keep it away from water and moisture.
 For optimal listening performance, make sure that the area around the wireless receiver module location is clear of any obstructions.
 If you hear no sound from the wireless surround speakers, switch the mode to Dolby Pro Logic II.
 In 2-CH mode, you will hear no sound from the wireless surround speakers.
| NOTE |
 If you place a speaker near your TV set, the screen color may be distorted because of the magnetic field.
 Place the wireless receiver module at the rear of the listening position. If the wireless receiver module is too close to the product, sound
from the speakers may be disrupted because of interference.
 If you use a device such as a microwave oven, wireless LAN Card, or any other device that uses the 2.4/5.8GHz frequencies near the
product, sound from the speakers may be disrupted because of interference.
 The maximum transmission distance from the product to the wireless receiver module is about 33 feet (10m), but may vary depending on
your operating environment. If a steel-concrete wall or metallic wall is between the product and the wireless receiver module, the system
may not operate at all, because the radio wave cannot penetrate metal.
 If the product doesn't make a wireless connection, you need to run an ID Set between the product and wireless receiver module. With the
product turned off, press "0""1""3""5" on the remote control. Turn on the wireless receiver module. Then, press and hold the “ID
SET” button on the back of the wireless receiver module for 5 seconds, and then turn the product on.

Connecting the FM Antenna

FM Antenna (supplied)

AUX VIDEO
SPEAKERS OUT
IN OUT
IMPEDANCE : 3

SURROUND

SURROUND OPTICAL
iPod LAN WIRELESS HDMI OUT 1 HDMI IN 2 DIGITAL FM ANT
AUDIO IN
N

1 . Connect the FM antenna supplied to the FM ANTENNA Jack.

2 . Slowly move the antenna wire around until you find a location where reception is good, then fasten it
to a wall or other rigid surface.

| NOTE |
 This product does not receive AM broadcasts.

| 18 English

HT-E5400_ZA_0417-1(D2D).indd 18 2012-04-17 오후 6:45:26

 Connecting to an iPod/iPhone

Using a USB Cable Using a Dock

03
Connections
Connect an iPod/iPhone using the USB cable to To view a video from your iPod on your TV, you
the front USB port. must also connect the Video Out jack on the
product to the Video In jack on your TV.
See page 20.

AUX VIDEO
SPEAKERS OUT
IN OU
OUT

IMPEDANCE : 3
5V 500mA

SURROUND

SURROUND OPTICAL
iPod LAN WIRELESS HDMI OUT 1 HDMI IN 2 DIGITAL FM ANT
AUDIO IN
N

5V 500mA

iPod

| NOTE |
 Make sure to connect the dock connector so that the label “” faces upward.

Attaching the Toroidal Ferrite Core to the Power Cord of the Main Unit

If you attach a Toroidal ferrite core to the power cord of the main unit, it will help to prevent RF
interference from radio signals.

AUX VIDEO
SPEAKERS OUT
IN OUT
IMPEDANCE : 3

SURROUND

SURROUND OPTICAL
iPod LAN WIRELESS HDMI OUT 1 HDMI IN 2 DIGITAL FM ANT
AUDIO IN

1. Pull the fixing tab of the Toroidal ferrite core to open it.
2. Make a loop twice in the main unit power cord.
3. Attach the Toroidal ferrite core to the main unit power cord as the figure shows and press it until it clicks.

English 19 |

HT-E5400_ZA_0417-1(D2D).indd 19 2012-04-17 오후 6:45:28

 Connections
Connecting to a TV

Select either Method 1 or Method 2.

• If you have set the product's remote control to operate your TV, press the TV SOURCE button on the remote control,
and then select the correct external source from the TV's source list (HDMI, Video In, etc.) to view video from the home
theater.

AUX VIDEO
IN OUT

AUX VIDEO
SPEAKERS OUT
IN OUT
IMPEDANCE : 3

SURROUND

SURROUND OPTICAL
iPod LAN WIRELESS HDMI OUT 1 HDMI IN 2 DIGITAL FM ANT
AUDIO IN

OPTICAL
HDMI OUT 1 HDMI IN 2 DIGITAL FM ANT
AUDIO IN

(Cable not supplied.)

Method 2
Method 1

HDMI IN VIDEO IN

Method 1 Connecting to a TV with an HDMI Cable - Best Quality (Recommended)

Connect an HDMI cable (not supplied) from the HDMI OUT jack on the back of the product to the HDMI IN
jack on your TV.

Method 2 Connecting to a TV with a Video Cable - Good Quality

Connect the supplied Video cable from the VIDEO OUT jack on the back of the product to the VIDEO IN
jack on your TV.

| NOTE |
 The VIDEO Out jack always outputs in the 480i resolution regardless of the resolution set in the Setup menu.
 Do not connect the unit through a VCR. Video signals fed through VCRs may be affected by copyright protection systems and
the picture will be distorted on the television.

| 20 English

HT-E5400_ZA_0417-1(D2D).indd 20 2012-04-17 오후 6:45:29

 Connecting to External Devices

03
To select the correct mode for an external device, press the FUNCTION button. Each time you press the button,
the mode changes in this order : BD/DVD  D. IN  AUX  R. IPOD  HDMI1  HDMI2  FM

Connections
R
Red

AUX VIDEO

W
White IN OUT

AUX VIDEO
SPEAKERS OUT
IN OUT
IMPEDANCE : 3

SURROUND

OPTICAL
SURROUND OPTICAL
iPod LAN WIRELESS HDMI OUT 1 HDMI IN 2 DIGITAL
AUDIO IN
FM ANT
1 HDMI IN 2 DIGITAL FM ANT
AUDIO IN

(Cable not supplied.)

Method 3
Method 1 Method 2
(Cable not supplied.) (Cable not supplied.)

External Devices
HDMI OUT OPTICAL OUT AUDIO OUT

Method 1 HDMI IN : Connecting to an External Component with an HDMI Cable

Connect an HDMI cable (not supplied) from the HDMI IN jack on the back of the product to the HDMI
OUT jack on your digital device.  Select the HDMI1 or HDMI2 mode.

Method 2 OPTICAL : Connecting an External Digital Audio Component

To connect the digital audio output of digital signal components such as Cable Boxes and Satellite
Receivers (Set-Top-Boxes).
Using a digital optical cable (not supplied), connect the Optical Digital Audio In jack on the product to the
Digital Optical Out jack of the external digital device using a digital optical cable.
 Select the D. IN mode.

Method 3 AUX IN : Connecting an External Analog Component

Using an RCA audio cable (not supplied), connect the AUDIO In jack on the product to the AUDIO Out
jack on the external analog component.  Select the AUX mode.
• Be sure to match the colors on the cable plugs to the colors on the input and output jacks.
| NOTE |
 To see video from your Cable Box/Satellite receiver, you must connect its video output directly to your TV.
 This system supports Digital sampling frequencies of 32 kHz or higher from external digital components.
 This system supports only DTS and Dolby Digital audio. MPEG audio, a bitstream format, is not supported.

English 21 |

HT-E5400_ZA_0417-1(D2D).indd 21 2012-04-17 오후 6:45:30

 Connections
Connecting to a Network Router Wireless Network

You can connect your product to your network

router using one of the methods illustrated below.
5V 500mA

Wired Network

AUX VIDEO
SPEAKERS OUT
IN OUT
IMPEDANCE : 3

SURROUND

SURROUND OPTICAL
iPod LAN WIRELESS HDMI OUT 1 HDMI IN 2 DIGITAL FM ANT
AUDIO IN

Wireless IP sharer

Broadband modem
(with integrated router)
Broadband
service Broadband
Or service

Router
| NOTE |
 If your wireless IP router supports DHCP, this product can
use a DHCP or static IP address to connect to the wireless
Broadband
network.
service
 Set your wireless IP router to Infrastructure mode. Ad-hoc
Broadband
modem mode is not supported.
 The product supports only the following wireless security
key protocols:
- WEP (OPEN/SHARED), WPA-PSK (TKIP/AES), WPA2-PSK
| NOTE | (TKIP/AES)
 Internet access to Samsung’s Software Update server  Select a channel on the wireless IP router that is not
may not be allowed, depending on the router you use or currently being used. If the channel set for the wireless IP
your ISP’s policy. For more information, contact your ISP router is currently being used by another device nearby, it
(Internet Service Provider). will result in interference and communication failure.
 DSL users, please use a router to make a network  If you select the Pure High-throughput (Greenfield)
connection. 802.11n mode and set the Encryption type on your router
 To use the AllShare Play function, you must connect your or AP to WEP, TKIP or TKIP-AES (WPS2Mixed), the product
PC to your network as shown in the illustrations on the will not support a connection in compliance with new Wi-
left. Fi certification specifications.
The connection can be wired or wireless.  Wireless LAN, by its nature, may cause interference,
depending on the operating conditions (AP performance,
distance, obstacles, interference by other radio devices,
etc).

| 22 English

HT-E5400_ZA_0417-1(D2D).indd 22 2012-04-17 오후 6:45:30

 Settings
The Initial Settings Procedure | NOTE |
 The product starts the wireless network connection
procedure by default. If you want to set up a wired

04
• The Home menu will not appear if you do not configure
connection, select Skip, and then go to "Configuring
the initial settings.

Settings
Your Network Connection" on page 31 after you have
• The OSD (On Screen Display) may change in this completed the Initial Settings Procedure.
product after you upgrade the software version.
 If you skip wireless network setup here, go to "Wireless
• The access steps may differ depending on the menu
Network" on page 32 to set up the product's wireless
you selected.
network connection later.
1 . Turn on your TV after connecting the product, 5 . The product searches for and then displays
and then turn on the product. When you turn all available wireless router network
on the product for the first time, the product connections.
automatically displays the Initial Settings
Language screen. Initial Settings > Network Settings (2/5)

Select your wireless router from the list:

1/4
Initial Settings > On-Screen Language
KIMING_VTOWER Refresh
Select a language for the on-screen TIAS
WPS(PBC)
displays. si-ap
▲ Previous
Dansk Nederlands Select English as the
on-screen menu
surlwang5
Next
English Eesti keel language. Add Network
Suomi Français Next Skip

Deutsch Ελληνικά
Magyar Italiano
Қазақ 한국어
▼

6 . Use the ▲▼ buttons to select a router, and

then press the E button. The Next button
2 . Use the ▲▼◄► buttons on the remote is highlighted.
to select the desired language, and then 7 . Press the E button to continue.
press the E button twice. The Start screen The Security Key screen appears.
appears.
| NOTE |
3 . Press the E button to start setup. The
Network Settings screen appears.  If you have a WPS(PBC) compatible router, select
WPS(PBC) instead, press the E button, and then follow
Initial Settings > Network Settings (1/5)
the directions on the screen. When done, go to Step 10.

The next step is to set up a wireless network using an

Initial Settings > Network Settings (4/5)
internal LAN Adapter.
Previous Enter security key.

Next - 0 entered WPS PIN

Skip a b c d e f 1 2 3 Previous

If you want to connect to your wired network, plug in a g h i j k l 4 5 6

Next
network cable.
Skip
m n o p q r 7 8 9

s t u v w x y z 0

A/a  Space   

4 . Press the E button to set up the product's

wireless network connection or select
Skip, and then press the E button to skip 8 . Enter your network's security key. When
network setup. If you selected Skip, go to done, use the ▲▼◄► buttons to select
Step 12. Next, and then press the E button.

English 23 |

HT-E5400_ZA_0417-1(D2D).indd 23 2012-04-17 오후 6:45:33

 Settings
| NOTE | 12 . Using the ▲▼ buttons, select the aspect ratio
 Enter numbers by pressing the number buttons on your that matches your screen, select Next, and
remote. then press the E button.
 Enter letters by selecting a letter using the ▲▼◄► You have four choices:
buttons, and then press E button. 16:9 Original - For widescreen TVs. Displays
 To display capital letters (or redisplay small letters if widescreen pictures in their original 16:9
capital letters are displayed), select A/a, and then press format and 4:3 pictures (the old, standard
the E button. format) in 4:3 pillar box format with black bars
on the left and right.
 To display symbols and punctuation, select , and then
press the E button. To redisplay letters, select , and 16:9 Full - For widescreen TVs. Displays
then press the E button. widescreen pictures in their original 16:9
format and expands 4:3 pictures to fill the
9 . If the connection is successful, the 16:9 screen.
Connection Complete screen appears. Select
4:3 Letter Box - For older, standard screen
Next, and then press the E button. The
analog TVs. Displays 4:3 pictures in full
Software Update screen appears.
screen and 16:9 pictures in letter box format
| NOTE | that retains the 16:9 aspect ratio but puts
 If the connection is not successful, select Next, and then black bars above and below the picture.
press the E button. After you have completed the Initial 4:3 Pan-Scan - For older, standard screen
Settings procedure, go to "Wireless Network" on page 32 analog TVs. Displays 4:3 pictures in full
to set up the product's wireless network connection. screen and 16:9 pictures in Pan-Scan format
10 . To upgrade the software, select Update that fills the screen, but cuts off the left and
now, and then press the E button. To skip right sides of the picture and enlarges the
the upgrade, select Update later, press the middle vertically.
E button, and go to Step 12.
Initial Settings > Complete
| NOTE |
Setup completed.
 If you skipped network set up, you must skip Software On-Screen Language  Press Smart Hub to
Update also. Network Settings 
enjoy variety of
Internet content.
OK
Software Upgrade -
11 . If there is a Software Update available,
TV Aspect 
the product downloads and installs the
Smart Hub
upgrade. This can take some time. If there
is no Software Update available, the "There
are no new software updates for you to
download. You already have the most up
to date version." message appears. Select 13 . The Setup completed screen appears. Check
Next, and then press the E button. The TV the settings to confirm they are correct.
Aspect Ratio screen appears. Select OK, and then press the E button.
The Home screen appears.
Initial Settings > TV Aspect Ratio | NOTE |
Set to match the type of television connected.
 If you want to display the Initial Setting screen again and
16:9 Original make changes, select the Reset option. (See page 30)
16:9 Full
4:3 Letter Box Select when connecting to a
Previous  If you use an HDMI cable to connect the product to an
Next
4:3 Pan-Scan
16:9 TV Screen. All content
will be displayed at original
Anynet+ (HDMI-CEC)-compliant Samsung TV and 1.) You
aspect ratio. Content
formatted in 4:3 will be
have set the Anynet+ (HDMI-CEC) feature to ON in both
displayed with black bars on
left and right.
the TV and the product and 2.) You have set the TV to a
language supported by the product, the product will select
that language as the preferred language automatically.

| 24 English

HT-E5400_ZA_0417-1(D2D).indd 24 2012-04-17 오후 6:45:34

 The Home Screen 2 . To access the menus, sub-menus, and
options on the Settings screen, please refer
to the remote control illustration below.

04
AllShare Play | NOTE |

Settings
Play videos, photos, or music from Disc or connected devices.
 If you leave the product in the stop mode for more than
3 5 minutes without using it, a screen saver will appear on
2
4 your TV. If the product is left in the screen saver mode for
5 more than 20 minutes, the power will automatically turn
1 off.
Smart Hub Disc to Digital Function Settings
Buttons on the Remote Control Used
for the Settings Menu
Smart Hub. Starts Smart Hub. From Smart Hub,
1 you can access Netflix, Pandora, YouTube, games, HOME REPEAT

and other apps. 1

AllShare Play. Play videos, photos or music content TOOLS INFO
2
from Disc, USB, PC or mobile devices.
Disc to Digital. Access you movie collection via 3
3 cloud storage anytime, any place without your DVD RETURN EXIT

disc. 2 4
TUNER
MEMORY MO/ST

4 Function. Select the audio/video input source.

1 HOME Button : Press to move to the Home screen.
Settings. Set various functions to suit your personal
5 2 RETURN Button : Return to the previous menu.
preferences.
E (Enter) / DIRECTION Button :
 Selecting an Option on the Home Screen
~ Press ▲▼◄► to move the cursor or select
1 . To select an option on the Home screen, 3 an item.
move the cursor using the ◄► buttons until it ~ Press the E button to activate the currently
highlights the option of your choice, and then selected item or confirm a setting.
press the E button.
4 EXIT Button : Press to exit the current menu.
Accessing the Settings Screen
| NOTE |
1 . Select Settings on the Home screen, and  The E button on the product's front panel can be
then press E. The Settings screen appears. used for same purpose as the E button on the remote
control.
3D Settings
Display
TV Aspect Ratio 16:9 Original Detailed Function Information
Smart Hub Screen Size Size 3
Audio
BD Wise On
Each Settings function, menu item, and individual
Network Resolution Auto option is explained in detail on-screen. To view an
Movie Frame (24Fs) Auto explanation, use the ▲▼◄► buttons to select the
System HDMI Color Format Auto
HDMI Deep Color Auto
function, menu item, or option.
Support
Progressive Mode Auto The explanation will usually appear on the right of
the screen. A short description of each Settings
function starts on the next page. Additional
information on some of the functions is also in the
Appendix of this manual.

English 25 |

HT-E5400_ZA_0418-1(D2D).indd 25 2012-04-18 오전 11:45:53

 Settings
Settings Menu Functions

Display Set up the 3D related functions.

 3D Blu-ray Playback Mode: Select whether to play a Blu-
ray Disc with 3D contents in 3D Mode. If you move to the
Home or Smart Hub Home menu while in 3D mode, the
3D Settings
product will switch to 2D automatically.
 Screen Size: Enter the size of the TV attached to the
product. The product will automatically adjust the 3D output
to the screen size of the TV.

Lets you adjust the output of the product to the screen size of
TV Aspect
your TV. See page 24, Step 12 for a description of the screen
Ratio
size options.

Smart Hub
Lets you select the optimal size for the Smart Hub Screen.
Screen Size

BD Wise is Samsung’s latest inter-connectivity feature.

When you connect a Samsung product and a Samsung TV
BD Wise with BD Wise to each other via HDMI, and BD Wise is on in
both the product and TV, the product outputs video at the
video resolution and frame rate of the Blu-ray/DVD Disc.

Lets you set the output resolution of the HDMI video signal to
Auto, 1080p, 1080i, 720p, 480p. If Composite is connected,
the resolution supports only 480i. The number indicates
Resolution
the number of lines of video per frame. The i and p indicate
interlaced and progressive scan, respectively. The more lines,
the higher quality.

Setting the Movie Frame (24Fs) feature to Auto lets the product
adjust its HDMI output to 24 frames per second automatically
for improved picture quality if attached to a 24Fs compatible
Movie Frame TV.
(24Fs) • You can enjoy the Movie Frame (24Fs) feature only on a TV
supporting this frame rate.
• Movie Frame is only available when the product is in the
HDMI 1080i or 1080p output resolution modes.

Lets you set the color space format for the HDMI output to
HDMI Color
match the capabilities of the connected device (TV, monitor,
Format
etc).

Lets you set the product to output video from the HDMI OUT
HDMI Deep
jack with Deep Color. Deep Color provides more accurate
Color
color reproduction with greater color depth.

Progressive
Lets you improve picture quality when viewing DVDs.
Mode

| 26 English

HT-E5400_ZA_0417-1(D2D).indd 26 2012-04-17 오후 6:45:46

 Audio Speaker
You can set the speaker options.
Settings

04
Equalizer Let you configure the Equalizer settings manually.

Settings
Lets you set the product so that the volume remains stable
Smart Volume when a scene change occurs or when you change the
channel.

Speaker Lets you select which speakers you want active, either the
Selection TV's speakers or the Home theater's speakers.

Lets you direct the sound from the TV to the Home Theater
speakers. Requires an HDMI connection and an Audio Return
Channel (ARC) compatible TV.
• When Audio Return Channel set to on, use HDMI Cable to
Audio Return
connect the product to the TV. At this time, optical input
Channel
does not work.
• When Audio Return Channel set to auto, use HDMI Cable to
connect the product to the TV. At this time, ARC and optical
input is selected automatically.

Let you set the Digital Output to match the capabilities of the
Digital Output AV receiver you’ve connected to the product. For more details,
please refer to the digital output selection table. (See page 58)

Lets you apply dynamic range control to Dolby Digital, Dolby

Digital Plus, and Dolby True HD audio.
 Auto: Automatically controls the dynamic range of Dolby
TrueHD audio, based on information in the Dolby TrueHD
soundtrack. Also turns dynamic range control on for Dolby
Dynamic
Digital and Dolby Digital Plus.
Range Control
 Off: Leaves the dynamic range uncompressed, letting you
hear the original sound.
 On: Turns dynamic range control on for all three Dolby
formats. Quieter sounds are made louder and the volume of
loud sounds is reduced.

When the product is attached to a digital TV, lets you adjust

Audio Sync the audio delay so that the audio syncs with the video. You
can set the delay between 0 and 300 milliseconds.

English 27 |

HT-E5400_ZA_0417-1(D2D).indd 27 2012-04-17 오후 6:45:46

 Settings
Network For more information about Network Settings and network
Network
functions, see "Networks and the Internet" starting on page
Settings
31.

Network Let you check whether a connection to the network and the
Status Internet have been established.

Lets you connect a Wi-Fi Direct device to the product using a

Wi-Fi Direct Peer-to-Peer network, without a wireless router. You can use
the device to control the product.

Lets you connect other types of Wi-Fi devices to the product

wirelessly. Requires that you create a security key which
Soft AP
you must enter into the other Wi-Fi devices when you are
connecting them to the network.

Lets you permit external devices such as smart phones to

AllShare
connect to the product and share content with or control the
Settings
product.

Lets you assign an identifying name to the product. You use

Device Name this name to identify the product when you are connecting
external Wi-Fi devices (smart phones, tablets, etc.) to it.

BD-Live Lets you allow, limit, or prohibit an Internet connection for the
Settings BD-Live service.

| 28 English

HT-E5400_ZA_0417-1(D2D).indd 28 2012-04-17 오후 6:45:46

 System Lets you re-run the Initial Settings procedure. See page 23 for
Initial Settings
details.

04
You can connect a wireless USB keyboard or mouse to

Settings
the USB port on the front of the product.
 Keyboard Settings: Lets you configure a wireless USB
keyboard connected to the product.
| NOTE |
 You can use the keyboard only when a QWERTY keyboard screen or
window appears in the Web Browser.
 Mouse Settings: Lets you configure a wireless USB mouse
connected to the product. You can use the mouse in the
product's menu in the same way you use a mouse on your
PC.

Device  To use a mouse with the product's menu:

Manager 1 . Connect the USB mouse to the product.
2 . Click the primary button you selected in Mouse Settings.
The Simple Menu appears.
3 . Click the menu options you want.
| NOTE |
 Depending on the model of the USB HID keyboard and mouse may not
be compatible with your product.
 Some HID keyboard keys may not work.
 Wired USB keyboards are not supported.
 Some applications may not be supported.
 If a wireless HID Keyboard does not operate because of interference,
move the keyboard closer to the product.

Anynet+ is a convenient function that offers linked operations

with other Samsung products that have the Anynet+ feature
Anynet+
and lets you control those products with one Samsung TV
(HDMI-CEC)
remote. To operate this function, you must connect this
product to an Anynet+ Samsung TV using an HDMI cable.

You can select the language you prefer for the On-Screen
menu, disc menu, subtitles, etc.
Language
• The language you select for the disc menu, disc audio, or
subtitles will only appear if it is supported on the disc.

English 29 |

HT-E5400_ZA_0417-1(D2D).indd 29 2012-04-17 오후 6:45:47

 Settings
The default PIN is 0000. Enter the default PIN to access the
security function if you haven't created your own password.
 BD Parental Rating: Prevents playback of Blu-ray Discs
with a rating equal to or above a specific age rating you
enter unless the PIN is entered.
 DVD Parental Rating: Prevents playback of DVDs with a
rating above a specific numerical rating you select unless
the PIN is entered.
 Change PIN: Change the 4-digit PIN used to access
Security security functions.

 If you forget your PIN

1 . Remove any disc or USB storage device.
2 . Press and hold the 5 button on the front panel for 5
seconds or more.
All settings will revert to the factory settings.
| NOTE |
 When the factory default settings are restored, all the user stored BD
data will be deleted.

You can specify the display brightness and time zone.

 Front Display: Lets you change the brightness of the front
panel.
General  Time Zone: You can specify the time zone that is applicable
to your area.
 Menu Transparency: Adjust the transparency of the menu
box.

Support Software For more information about the Software Update function, see
Update "Upgrading Software" on page 35.

Contact
Provides contact information for assistance with your product.
Samsung

When activated, lets Samsung Call Center agents diagnose

Remote and fix problems with the product remotely. Requires an active
Management Internet connection. Remote Management service might not
be available in some countries.

All settings will revert to the default except for the network
Reset and Smart Hub settings. The default security password is
0000.

| 30 English

HT-E5400_ZA_0417-1(D2D).indd 30 2012-04-17 오후 6:45:47

 Networks and the Internet  Wired - Manual
If you have a static IP address or the Automatic
When you connect this product to a network, procedure does not work, you'll need to set the

04
you can use network based applications and Network Settings values manually.
functions such as Smart Hub and BD-LIVE, and

Settings
upgrade the product's software through the After following Steps 1 to 3 above:
network connection. For more information about 1 . Select Start in the Network Settings screen,
accessing and using Internet services, see the and then press the E button. The Network
Network Services chapter of this manual on pages Status screen appears. The product attempts
50~53. Instructions for configuring the network to verify the network connection and fails.
connection start below.

Configuring Your Network Connection Network Settings

Wired network connection failed.

Before you begin, contact your ISP to find out
MAC Address XX:XX:XX:XX:XX:XX
if your IP address is static or dynamic. If it is IP Address 0.0.0.0 Previous
Subnet Mask 0.0.0.0
dynamic, and you have a wired or wireless Gateway 0.0.0.0 IP Settings
network, we recommend using the Automatic DNS Server 0.0.0.0
Retry

configuration procedures described below. Unable to connect to the network. Try the following:
check if your IP address is set correctly in IP Settings.
OK
Contact your Internet Service Provider for more information.
If you are connecting to a wired network, connect
the product to your router using a LAN cable
before you start the configuration procedure.
If you are connecting to a wireless network, 2 . Select IP Settings on the right of the screen,
disconnect any wired network connection before and then press E button.
you begin. The IP Settings screen appears.
To begin configuring your network connection, 3 . Select the IP Mode field, and then set it to
follow these steps: Manual.
1 . In the Home screen, select Settings, and 4 . Use the number keypad on your remote to
then press the E button. enter the Network values. Use the ▲▼◄►
2 . Select Network, and then press the E buttons on the remote to move from entry
button. field to entry field.
3 . Select Network Settings, and then press the | NOTE |
E button.  You can get these values from your Internet provider. You
4 . Go to the instructions for Wired networks can also view these values on most Windows computers.
starting below or the instructions for Wireless For instructions, see "Getting the Network Settings
networks starting on page 32. Values." on this page.
5 . When done, highlight OK, and then press
Wired Network E button. The product verifies the network
connection and then connects to the
 Wired – Automatic network.

After following Steps 1 to 3 above: < Getting the Network Settings Values >
You can view your Network Settings values on
1 . Select Start in the Network Settings screen,
most Windows computers. To view the Network
and then press the E button. The product
Settings values, follow these steps:
detects the wired connection, verifies the
network connection and then connects to the • Windows XP
network.
1 . Right click the Network icon on the bottom
right of the Windows desktop.

English 31 |

HT-E5400_ZA_0417-1(D2D).indd 31 2012-04-17 오후 6:45:47

 Settings
2 . In the pop-up menu, click Status.
Network Settings
3 . On the dialog that appears, click the Support
tab. Select your wireless router from the list:
1/10
iptime23
4 . On the Support tab, click the Details button. ELT
Refresh
WPS(PBC)
5 . The Network settings are displayed. JSY
Previous
KT_WLAN_C361
Next
• Windows 7 Mirhenge_edu
Cancel
SO070VOIP
1 . Click the Network icon on the bottom right of
the Windows desktop.
2 . In the pop-up menu, click Network and
Sharing Center. 2 . Select the desired network, and then press
the E button.
3 . On the dialog that appears, click the Local
Area Connection or Wireless Network 3 . Select Next, and then press the E button
Connection depending on your network again.
connection. 4 . On the Security screen, enter your network's
4 . On the Support tab, click the Details button. Security Code or Pass Phrase.
The Network settings are displayed. Enter numbers directly using the number
buttons on your remote control. Enter letters
| NOTE | by selecting a letter with an arrow button, and
 Depending on your Windows version, the information may then pressing E button.
differ. 5 . When done, select Next at the right of the
screen. The product verifies the network
Wireless Network connection and then connects to the
You can setup a wireless network connection in network.
three ways:
| NOTE |
- Wireless Automatic
 You should be able to find the Security Code or Pass
- Wireless Manual Phrase on one of the set up screens you used to set up
- WPS(PBC) your router or modem.
When you configure the wireless network
connection, any wireless network devices currently  Wireless (General) - Manual
connected through the product or, if applicable,
the product's current wired connection, will be If you have a static IP address or the Automatic
disconnected. procedure does not work, you'll need to set the
Network Settings values manually.
 Wireless (General) - Automatic After folloiwng Steps 1 to 3 in "Configuring Your
Network Connection" on page 31.
After following Steps 1 to 3 in "Configuring Your
Network Connection" on page 31. 1 . Select Start in the Network Settings screen,
and then press the E button. The product
1 . Select Start in the Network Settings screen,
searches for and then displays a list of the
and then press the E button.
available networks.
The product searches for and then displays a
list of the available networks. 2 . Select the desired network or the Add
Network, and then press the E button.
3 . Select Next, and then press the E button
again.

| 32 English

HT-E5400_ZA_0417-1(D2D).indd 32 2012-04-17 오후 6:45:48

 4 . If you select the Add Network, enter your After following Steps 1 to 3 in "Configuring Your
wireless router's name to connect. Network Connection" on page 31.
Enter numbers directly using the number

04
1 . Select Start in the Network Settings screen,
buttons on your remote control. Enter letters
and then press the E button.
by selecting a letter with the ▲▼◄► buttons,

Settings
and then pressing the E button.
Select Next, and then press the E button Network Settings

again. You can select security type, and then Select your wireless router from the list:
1/10
select Next, and then press the E button iptime23
Refresh
again. ELT
WPS(PBC)
JSY
5 . On the Security screen, enter your network's Previous
KT_WLAN_C361
Security Code or Pass Phrase. Mirhenge_edu
Next
Cancel
Enter numbers directly using the number SO070VOIP
buttons on your remote control. Enter
letters by selecting a letter with the ▲▼◄►
buttons, and then pressing the E button. 2 . Select WPS(PBC), and then press the E
6 . When done, select Next at the right of the button.
screen, and then press the E button. 3 . Press the WPS(PBC) button on your router
7 . The Network Status screen appears. within two minutes. Your product automatically
The product attempts to verify the network acquires all the network settings values it needs
connection and fails. and connects to your network.
The Network Status screen appears. The
8 . Select IP Settings on the right of the screen, product connects to the network after the
and press the E button. The IP Settings network connection is verified.
screen appears.
9 . Select the IP Mode field, and then set it to Wi-Fi Direct
Manual.
The Wi-Fi Direct function allows you to connect Wi-Fi
10 . Use the number keypad on your remote to Direct devices to the product and each other using a
enter the Network values. Use the ▲▼◄► peer-to-peer network, without a wireless router.
buttons on the remote to move from entry
1 . Turn on the Wi-Fi direct device and activate
field to entry field.
its Wi-Fi Direct function.
| NOTE | 2 . In the Home screen, select Settings, and
 You can get these values from your Internet provider. You then press the E button.
can also view these values on most Windows computers. 3 . Select Network, and then press the E button.
For instructions, see "Getting the Network Settings 4 . Select Wi-Fi Direct, and then press the E
Values." on page 31. button.
The Wi-Fi Direct devices that you can
11 . When done, highlight OK, and then press E
connect appear.
button. The Network Status screen appears.
The product verifies the network connection
and then connects to the network. When it Wi-Fi Direct

is done, highlight OK, and then press E Device Name : [HTS]E5400

Display
Select your Wi-Fi Direct device to connect to.
button. Audio
AndroidXXXXXXX Disconnected

Network
 WPS(PBC) Refresh
System Close

One of the easiest ways to set up the wireless Support

network connection is using the WPS(PBC) m Move " Enter ' Return

function. If your wireless router has a WPS(PBC)

button, follow these steps:

English 33 |

HT-E5400_ZA_0417-1(D2D).indd 33 2012-04-17 오후 6:45:49

 Settings
5 . You have three ways to complete the Wi-Fi | NOTE |
connection:  The wired or wireless network connection will be
• Through the Wi-Fi device. disconnected when you use the Wi-Fi Direct function.
• Through the product using PBC.
Soft AP
• Through the product using a PIN.
Soft AP lets you connect other Wi-Fi devices to
Each is covered below.
your network through the product and lets them
Through the Wi-Fi Device access the Internet.
1 . On the Wi-Fi device, follow the procedure on It requires that you create a security key which you
the device for connecting to another Wi-Fi must enter into the other Wi-Fi devices when you
Direct device. See the device's user manual are connecting them to the network.
for instructions. 1 . In the Home screen, select Settings, and
2 . When you have completed the procedure, then press the E button.
you should see a pop-up on your TV screen 2 . Select Network, and then press the E
saying that a device that supports Wi-Fi button.
Direct has requested to connect. Select OK,
3 . Select Soft AP, and then press the E
and then press the E button to accept.
button.
3 . The Connecting pop-up appears, followed
4 . Select On or Off, and then press the E
by the Connected pop-up. When it closes,
button.
you should see the device listed on the Wi-Fi
Direct screen as connected. < To Set the Soft AP Security Key >
Through the Product Using PBC 1 . On the Soft AP screen, select Security Key,
1 . Select the Wi-Fi Direct device you want to and then press the E button. The Security
connect to this product, and then press the Key screen appears.
E button. The PBC/PIN pop up appears. 2 . On the Security key screen, enter a security
2 . Select PBC, and then press the E button. key. Enter numbers directly using the number
The PBC pop-up appears. buttons on your remote control. Enter
letters by selecting a letter with the ▲▼◄►
3 . Press the PBC button on the Wi-Fi Direct buttons, and then pressing the E button.
device within 2 minutes.
3 . When done, use the ▲▼◄► buttons to
4 . The Connecting pop-up appears, followed move to DONE at the bottom of the screen,
by the Connected pop-up. When it closes,
and then press the E button.
you should see the device listed on the Wi-Fi
Direct screen as connected. When you connect a Wi-Fi device through the
Through the Product Using a PIN connection procedure on the device, you must
enter the security key you created here into the
1 . Select the Wi-Fi Direct device you want to appropriate field.
connect to this product, and then press the
E button. The PBC/PIN pop up appears. AllShare Settings
2 . Select PIN, and then press the E button.
The AllShare Settings screen lists your network
The PIN pop-up appears.
connected AllShare devices and their IP
3 . Note the PIN code in the pop-up, and then addresses. Through this screen, you can allow
enter it into the appropriate field in the Wi-Fi a device to access the product, deny access, or
Direct device you want to connect. delete the device from the AllShare list.
4 . The Connecting pop-up appears, followed
by the Connected pop-up. When it closes, 1 . In the Home screen, select Settings, and
you should see the device listed on the Wi-Fi then press the E button.
Direct screen as connected. 2 . Select Network, and then press the E
button.

| 34 English

HT-E5400_ZA_0417-1(D2D).indd 34 2012-04-17 오후 6:45:54

 3 . Select AllShare Settings, and then press the Online
E button.
Your product must be connected to the Internet to
4 . Select a device, and then press the E

04
use the Online function.
button. The AllShare Settings pop-up
1 . Select Online, and then press the E button.

Settings
appears.
5 . Select Allow, Deny, or Delete from List, and The Connecting to Server message appears.
then press the E button. 2 . If there is a download available, the Download
pop-up appears with a progress bar and the
The AllShare Settings screen only displays devices download starts.
if you have established networked connections
3 . When the download is complete, the
to AllShare devices. For more information about
Upgrade Query window appears with three
AllShare networked devices, see pages 37~38.
choices: Update now, Update later or
Don't update.
Upgrading Software 4 . If you select Update now, the product
upgrades the software, turns off, and then
The Software Update menu allows you to turns on automatically.
upgrade the product’s software for performance 5 . If you do not make a selection in one minute
improvements or additional services. or select Update later, the product stores
the new upgrade software. You can upgrade
• Never turn the product off or back on manually during the software later using the By Downloaded
the update process. function.
1 . In the Home menu, select the Settings, and 6 . If you select Don't update, the product
then press the E button. cancels the upgrade.
2 . Select Support, and then press the E
By USB
button.
3 . Select Software Update, and then press the 1 . Visit www.samsung.com.
E button. 2 . Click SUPPORT on the top right of the page.
4 . Select one of the following methods:
3 . Enter the product's model number into the
• Online search field, and then click Find Product.
• By USB 4 . Click Get downloads in the center of the
• By Disc page below the Downloads header.
• By Downloaded 5 . Click Firmware in the center of the page.
• Standby Mode Upgrade 6 . Click the ZIP icon in the File column on the
right side of the page.
5 . Press the E button.
Directions for each method begin below. 7 . Click OK in the pop-up that appears to
download and save the firmware file to your
| NOTE | PC.
 The upgrade is complete when the product turns off, and 8 . Unzip the zip archive to your computer. You
then turns on again by itself. should have a single folder with the same
 Samsung Electronics takes no legal responsibility for product name as the zip file.
malfunction caused by an unstable Internet connection or 9 . Copy the folder to a USB flash drive.
consumer negligence during a Software Update.
10 . Make sure no disc is inserted in the product,
 If you want to cancel the upgrade while the upgrade and then insert the USB flash drive into the
software is downloading, press the E button. USB port of the product.

English 35 |

HT-E5400_ZA_0417-1(D2D).indd 35 2012-04-17 오후 6:45:54

 Settings
11 . In the product’s menu, go to Settings > By Downloaded
Support > Software Update.
The By Downloaded option lets you upgrade
12 . Select By USB.
using a file the product downloaded earlier but
| NOTE | you decided not to install immediately.
 There should be no disc in the product when you upgrade 1 . If upgrade software has been downloaded,
the software using the USB Host jack. you will see the software version number to
 When the Software Update is done, check the software the right of By Downloaded.
details in the Software Update menu. 2 . Select By Downloaded, and then press the
 Do not turn off the product during the Software Update. It E button.
may cause the product to malfunction. 3 . The product displays a message asking if you
 Software Updates using the USB Host jack must be want to upgrade. Select Yes. The product
performed with a USB flash memory stick only. begins the upgrade.
4 . When the update is complete, the product
By Disc turns off automatically, and then turns on.
| NOTE |
1 . Visit www.samsung.com.
 When the system upgrade is done, check the software
2 . Click SUPPORT on the top right of the page.
details in the Software Update menu.
3 . Enter the product's model number into the
 Do not turn off the product during the Software Update. It
search field, and then click Find Product.
may cause the product to malfunction.
4 . Click Get downloads in the center of the
page below the Downloads header. Standby Mode Upgrade
5 . Click Firmware in the center of the page.
You can set the Standby Mode Upgrade function
6 . Click the ZIP icon in the File column on the
so that the product downloads new upgrade
right side of the page.
software when it is in Standby mode.
7 . Click OK in the pop-up that appears to In Standby mode, the product is off, but its
download and save the firmware file to your Internet connection is active. This allows
PC. the product to download upgrade software
8 . Unzip the zip archive to your computer. You automatically, when you are not using it.
should have a single .RUF file.
1 . Press the ▲▼ buttons to select Standby
9 . Write the RUF file onto a disc. We Mode Upgrade, and then press the E
recommend a CD-R or DVD-R. button.
10 . Finalize the disc before you remove it from 2 . Select On or Off.
your computer. If you select On, the product will automatically
11 . Insert the disc into the product. download new upgrade software when it
is in Standby mode with the power off. If
12 . In the product’s menu, go to Settings >
it downloads new upgrade software, the
Support > Software Update.
product will ask you if you want to install it
13 . Select By Disc. when you turn the product on.
| NOTE | | NOTE |
 When the system upgrade is done, check the software  To use Standby Mode Upgrade function, your product
details in the Software Update menu. must be connected to the Internet.
 Do not turn off the product during the Software Update.  If this function does not appear, you can upgrade to the
It may cause the product malfunction. latest software and use it.

| 36 English

HT-E5400_ZA_0417-1(D2D).indd 36 2012-04-17 오후 6:45:55

 Media Play
Your Blu-ray product can play Disc and USB • Use the ◄► buttons to select an item, press
contents and the contents located on your PC, the TOOLS button to display the Tools menu,
DLNA compatible mobile phone, or NAS using the select Play, and then press the E button. To

05
AllShare Play function. For more information about view or play another item, press the RETURN
AllShare Play, refer to page 40. (') button, and then repeat the process

Media Play
described in the first sentence.

The AllShare Play Screen  Playing Video, Photo, or Music Content

To access the AllShare Play screen, select the 1 . Make sure that the source of the content
AllShare Play icon on the Main screen, and then you want to play or view is connected to or
press the E button. inserted into the product.
2 . Use the ▲▼ buttons to select Videos,
Using the AllShare Play Screen Photos, or Music, and then press the E
button. The first source selection on the right
AllShare Play / My List /
side is highlighted.
Latest play 3 . Use the ▲▼ buttons to select the source of
My List Recently played files will be displayed here. the content, and then press the E button.
Videos
What's New Recently Updated 09.Jan.2012
| NOTE |
Photos
View More  Sources displayed for each content type may differ.
SAM_0001 SAM_0002 SAM_0003 SAM_0004 SAM_0005

Music
Playlist
No playlists have been created.
4 . To control the playing of Videos, Photos, or
Create a playlist to quickly and easily access your content.
Music, see:
a Login ' Return
• Controlling Video Playback on page 42.
• Controlling Music Playback on page 44.
When the AllShare Play screen appears, it displays
• Playing Photo Contents and Using the Tools
My List and a list of content types - Videos,
Menu when a File is Highlighted on pages
Photos, and Music - on the left side. On the right,
45~48.
it displays, by default, the content in My List: a
list of recently played or viewed items, a list of the | NOTE |
newest items you have viewed or listened to, and  Depending on how and when you attach a content source
your most recent Playlist. If you have never played to the product and the content type, the product may
or viewed any items, or created a Playlist, this area display a different series of screens to start playback. For
will be empty. alternative playback methods see:
 Playing My List Items • Playing Files on a USB Storage Device or iPod/iPhone
on page 38.
To play displayed My List items, you must have
the source of the items connected to or inserted • Playing Commercial Video Discs on page 39.
in the product. For example, if recently played My • Playing Commercial Audio Discs on page 39.
List photos came from a DVD disc, you must have • Playing a Disc with User Recorded Content on page 40.
that disc in the product to view them.
To play or view My List items, perform one of the
actions below:
• Use the ◄► buttons to select an item you
want to view or play, and then press the E
button. To view or play another item, press
the RETURN (') button, and then repeat the
process described in the first sentence.

English 37 |

HT-E5400_ZA_0417-1(D2D).indd 37 2012-04-17 오후 6:45:55

 Media Play
Playing Files on a USB Storage 3 . The kind of content you selected on the
connected device is displayed. Depending
Device or iPod/iPhone
on how the contents is arranged, you will see
You can play multimedia files located on a either folders, individual files, or both.
connected USB device. 4 . Using the ▲▼◄► buttons on your remote,
select the desired contents. To open a folder,
1 . With the product turned off, connect a USB
select it, and then press the E button.
storage device or an iPod/iPhone.
To play a file, select it, and then press the E
2 . Turn on the product. When the Main screen button.
appears, select AllShare Play > Videos,
5 . Press the RETURN (') button to exit a folder
Photos or Music > Connected Device, and
or to return to the Main screen.
then press the E button.
| CAUTION |
AllShare Play  You can play a video only when you use the iPod Dock.
Play videos, photos, or music from Disc or connected devices.
| NOTE |
 To prevent possible damage to the USB memory, you
must remove the USB storage device safely using the
“Safely Remove USB” function. Press the HOME button
Smart Hub Disc to Digital Function Settings to move to the Home menu, select the YELLOW (C)
button, and then press the E button.
 Safely Remove USB
 The Photos menu does not support iPods or iPhones.
OR  Only the playback screen will appear on the TV. View other
1-1. With the product turned on, connect a USB iPod screens on the iPod player.
storage device or an iPod/iPhone.  If the connected iPod does not support video playback, the
2-1. When screen below appears, use the ▲▼ "Playing video files is not supported on this iPod model."
buttons to select the kind of content you message appears when you select the Video menu.
want to view or play, and then press the E
button.
iPod/iPhone Models You Can Use
with This Product
AllShare Play
New device connected.
Play videos,
ss, photos, or music from Disc or connecte
connected
ed devices.
USB DISK iPod touch 3rd/2nd/1st generation
Videos
iPod classic / iPod with video
Photos
Music
iPod with dock connector
iPod with Click Wheel
" Enter ' Return
Smart Hub Disc to Digital Function Settings
iPod nano 5th/4th/3rd/2nd generation
iPhone 4S / iPhone 4
 Safely Remove USB
iPhone 3GS / iPhone 3G / iPhone
| NOTE |
 Even though the product will display all available folders,
it will only display files of the content type you selected
in Step 2 or 2-1. For example, if you selected music, you
will only be able to see music files. You can change this
selection using AllShare Play.

| 38 English

HT-E5400_ZA_0417-1(D2D).indd 38 2012-04-17 오후 6:45:59

 The Function Screen Playing Commercial Audio Discs
On the Function Screen, you can select the audio 1 . Place a pre-recorded, commercial audio disc

05
and/or video input source to view or listen to. into the disc tray with the disc’s label facing up,
and then close the tray. The AllShare Play Music

Media Play
| NOTE | screen appears listing the tracks. Playback of
 You can also change sources by pressing the Function button the first track starts automatically.
in the upper right of the remote.
AllShare Play / Music / Audio CD 1 / 17

To access the Function Screen, select the ► TRACK 001 03:59

TRACK 002 04:34
04 34
Function icon on the Main screen, and then press TRACK 003 04:24
the E button. TRACK 004 04:01
TRACK 005 04:26
TRACK 006 05:07 ‫ ٭‬TRACK 001

Options on the Function Screen TRACK 007 04:47

TRACK 008 03:59
00:00 / 03:59
To select, highlight an option using the ▲▼ TRACK 009 04:34
TRACK 010 04:02
buttons, and then press the E button.
b Page Move / Tools ' Return

Select to listen to the digital audio

Digital In 2 . To play a particular track, use the ▲▼ buttons
source connected to Digital Audio In.
on the remote to select the track, and then
Select to listen to audio from the press the E button.
AUX analog audio source connected to
Audio In.  Music Screen Controls
Select to listen to music or view video
Pause a track.
Remote iPod from the iPod connected to the iPod
jack. Play a track.
Select to view video from the device Repeat one track or all tracks.
HDMI IN 1
connected to HDMI IN 1.
Play tracks in random order.
Select to view video from the device
HDMI IN 2 Display the Equalizer.
connected to HDMI IN 2.
Tuner Select to listen to the FM radio. Adjust the equalizer manually.
(Only when equalizer mode is On)

Playing Commercial Video Discs | NOTE |

1 . Place a disc into the disc tray with the disc’s  The Music Screen controls are only accessible when a track
label facing up and then close the disc tray. is playing.
Playback starts automatically.  All controls do not appear at the same time.
If playback does not start automatically, press  For more information about playing music, go to "Controlling
the 6 button on your remote or select the Music Playback" on page 44.
AllShare Play option on the Main screen,
and then press the E button. See "Playing
Video, Photo, or Music Content" on page 37.

English 39 |

HT-E5400_ZA_0417-1(D2D).indd 39 2012-04-17 오후 6:46:08

 Media Play
Playing a Disc with User Recorded Using the AllShare Network
Content Function
You can play multimedia files you have recorded AllShare lets you play Videos, Photos, or Music
on DVD or CD discs. located on your PC or your DLNA compatible
device through the product using a wireless
1 . Place a user recorded disc into the disc
network connection.
tray with the disc’s label facing up, and then
close the tray. The Device Connected pop-up To Download the AllShare Software
appears.
To use AllShare with your PC or DLNA device, you
2 . Use the ▲▼ buttons to select the type of
must install AllShare software on your PC.
content you want to view or play - Videos,
Photos, or Music - and then press the E You can download the PC software and get
button. detailed instructions for using AllShare from the
Samsung.com website.
| NOTE |
1 . Go to www.samsung.com.
 Even though the product will display folders for all content
2 . Click Support at the top of the page.
types, it will only display files of the content type you selected
in Step 2. For example, if you selected music, you will only 3 . On the Support page, enter the model
be able to see music files. You can change this selection number of your product into the Model
using AllShare Play. Number field.
4 . On the page that appears, click Get
3 . Use the ▲▼◄► buttons to select the folder downloads on the left side under Downloads.
containing the content type you selected in Step The Download Center appears.
2, and then press the E button.
5 . On the Download Center page, click the
4 . If you selected Music, the AllShare Play Music Software tab.
screen appears listing the music files on the
disc. Use the ▲▼ buttons to select the file you 6 . On the software tab, click the File icon on the
want to play, and then press the E button. right side of the AllShare line.
5 . If you selected Photos, the AllShare Play Photos 7 . In the pop-up that appears, click Save File.
screen appears listing the photos on the disc. 8 . Find the AllShare install file on your disk, and
Use the ▲▼◄► buttons to select the photo you then double click the file.
want to view, and then press the Ebutton. 9 . In the pop-up that appears, click Run, and
6 . If you selected Videos, the AllShare Play Videos then follow the directions that appear on your
screen appears listing the video files on the disc. screen.
Use the ▲▼◄► buttons to select the video you Download the AllShare Installation/Instruction
want to watch, and then press the E button. manual from the same Software Tab by clicking
| NOTE | the corresponding PDF file symbol in the File
column on the right. The file, in PDF format, will
 For the Music and Video folders, you can also push the
download and open. You can view and/or save
TOOLS button on your remote, and then select Play Folder to
the file.
play or view all the files in the folder automatically. Select the
folder first before pushing the TOOLS button.
 For more information about playing music, go to Controlling
Music Playback on page 44.
 For more information about playing photo contents, go to
Playing Photo Contents and Using the Tools Menu when a
File is Highlighted on pages 45~48.
 For more information about playing video contents, go to
Controlling Video Playback on page 42.

| 40 English

HT-E5400_ZA_0417-1(D2D).indd 40 2012-04-17 오후 6:46:12

 Playing Content Located on Your PC or Controlling the Playback of Content
DLNA Device through the Product Located on Your PC with Your Smart
Phone

05
PC

Media Play
Product
PC
5V 500mA
Product
Play back 5V 500mA

PC's files Play back

PC's files
AllShare Connection
AllShare Control PC's files to
1 . Connect the product, your PC, and/or your Connection Product
DLNA compatible cell phone to the same Smart Phone
wireless network.
2 . Follow the directions in the AllShare software (Only available with Samsung phones supporting
Installation/Instruction manual to set up AllShare functionality.)
devices and files for playing or viewing. 1 . Connect the product, your PC, and your
3 . Select AllShare Play in the product's Home DLNA compatible cell phone to the same
screen, and then press the E button. The wireless network.
AllShare Play screen appears. 2 . Follow the directions in the AllShare software
4 . Select the connected DLNA compatible Installation/Instruction manual to set up
device or your PC, and then press the E devices and files for playing or viewing.
button. A screen listing the available files 3 . On your computer, using the AllShare
appears. software, confirm your phone is connected.
5 . Select the file you want to play or view, and 4 . On the phone, select the file you want to view
then press the E button. or play, and then select the Blu-ray product
as the playback device.
5 . On the phone, start playback.

English 41 |

HT-E5400_ZA_0417-1(D2D).indd 41 2012-04-17 오후 6:46:12

 Media Play
Controlling Video Playback
You can control the playback of video files located on Blu-ray, DVD, and CD discs, and on USB storage
devices. Depending on the disc, some of the functions described in this manual may not be available.
Buttons on the Remote Control used for Video Playback
DISC MENU TITLE MENU  Using the disc menu, title menu, popup
0 POPUP
menu and title list

During playback, press this button to

DISC MENU
display the Disc menu.
MUTE

HOME REPEAT
During playback, press this button to
display the Title menu.
TITLE MENU
• If your disc has a playlist, press the
 Repeat Playback GREEN (B) button to go to the playlist.
1 . During playback, press the REPEAT During playback, press this button to
POPUP MENU
button on the remote control. display the Pop-up menu.
2 . Press the ▲▼ buttons to select a
Chapter, All or Title, then press the DISC MENU or During playback, press this button to
E button. TITLE MENU display the title list.
| NOTE |  Playback related buttons
Repeat a Title  The screen may not display Chapter or Title The product does not play sound in Search, Slow,
or Chapter immediately. Continue to press the ▲▼ or Step mode.
buttons until your choice is inside the blue
field. 6 Starts playback.
3 . To return to normal play, press the 5 Stops playback.
REPEAT button again, press the
▲▼ buttons to select Off, and then 7 Pauses playback.
press the E button. During playback, press the 3 or 
1 . During playback, press the REPEAT Fast Motion button.
button on the remote control. Play Each time you press the 3 or 
2 . Press the ▲▼ buttons to select button, the playback speed will change.
Repeat A-B.
In pause mode, press the  button.
| NOTE | Slow Motion
Each time you press the  button, the
Play
 The screen may not display Repeat A-B playback speed will change.
immediately. Continue to press the ▲▼
buttons until Repeat A-B is inside the blue In pause mode, press the 7 button.
Step Motion
field. Each time you press the 7 button, a
Repeat a Play
new frame appears.
Section 3 . Press the E button at the point
where you want repeat play to start (A). During playback, press the 1 or 2
4 . Press the E button at the point button.
where you want repeat play to stop (B). Skip Motion
Each time you press 1 or 2 button,
5 . To return to normal play, press the Play
the disc moves to the previous or next
REPEAT button again. chapter or file.
6 . Press the E button.
| NOTE |
 You must set point (B) at least 5 seconds of
playing time after point (A).

| 42 English

HT-E5400_ZA_0417-1(D2D).indd 42 2012-04-17 오후 6:46:15

 Using the TOOLS Menu Menu that appears only when BD/DVD disc
During playback, press the TOOLS button. plays

05
Select to move to a desired title if Play from the Select to play the movie from the

Media Play
the disc has more than one title, to a beginning beginning.
desired scene, or, using Time Search,
to a specific point in a movie or video. Select to move to a chapter that you
Title Search Chapter Search
With Time Search, you designate desire to watch.
Time Search
the specific point by entering a time Select to set the desired audio
coordinate in the following format language.
00:00:00 (hours, minutes, seconds) Audio - You can also operate this function
using the remote. by pressing the AUDIO button on the
Select to repeat a specific Title, Chapter remote control.
(BD/DVD discs only) or marked section. Select to set the desired subtitle
Repeat Mode
Works the same as the REPEAT button. language.
See page 42.
Subtitle - You can also operate this function
Select to set the desired full screen by pressing the SUBTITLE button on
Full Screen size. You can select Original, Mode1 the remote control.
(larger), and Mode2 (largest).
To view a scene from another angle.
Select to set the picture mode. The Angle option displays the number
Angle
- Dynamic : Choose this setting to of angles available to view (1/1, 1/2,
increase sharpness. 1/3, etc.).
- Standard : Choose this setting for BONUSVIEW
most viewing applications. Video / Select to set the desired bonusview
- Movie : This is the best setting for BONUSVIEW option.
watching movies. Audio
- User : Lets you adjust the sharpness
and noise reduction function
Menu that appears only when a file plays
respectively.
Picture Mode
| NOTE |
Go to Videos
 When you select User, the User Move to video list screen.
List
Settings screen appears. Select an
option, press E, use the ◄► Scene Search Search the video file by the scene.
buttons to make an adjustment, and Information Check the video file's information.
then press E. Press the RETURN
(') button to go back to the TOOLS
menu. | NOTE |
 When you use the BD wise function,  Depending on the disc or storage device, the Tools menu
this menu will not appear. may differ. All options may not be displayed.

Equalizer Mode Select to use the Equalizer.

Select to set the Equalizer.
Equalizer | NOTE |
Settings  It only appears when equalizer
mode is on.

English 43 |

HT-E5400_ZA_0417-1(D2D).indd 43 2012-04-17 오후 6:46:17

 Media Play
Controlling Music Playback Shuffling Tracks on an Audio CD

You can control the playback of music content You can set the product to play tracks on an audio
located on a DVD, CD, or a USB storage device. CD (CD-DA/MP3) at random.

Buttons on the Remote Control used 1 . During playback, use the ► button to select
in the lower right corner of the screen,
for Music Playback
and then press the E button.
2 . Use the ▲▼ to set the Shuffle Mode On or
1 2 3 Off, and then press the E button.
6 4 5 6
Creating a Playlist
7 8 9
DISC MENU TITLE MENU

0 POPUP
AllShare Play / Music / Audio CD 1 / 17

1 ► TRACK 001 03:59

5 TRACK 002
TRACK 003
04
04:34
34
04:24
2 TRACK 004 04:01
MUTE
TRACK 005 04:26
4 3 TRACK 006 05:07 ‫ ٭‬TRACK 001

TRACK 007 04:47

TRACK 008 03:59
Fast Play (Audio CD (CD-DA) only) TRACK 009 04:34
00:00 / 03:59

TRACK 010 04:02

During playback, press the 3 or  button.
1
Each time you press the 3 or  button, the b Page Move / Tools ' Return

playback speed will change.

1 . With the Playback screen displayed, press
2 7 button : Pause a track. the TOOLS button. The Tools menu appears.
3 6 button : Plays the currently selected track. 2 . Use the ▲▼ buttons to select Selection
Play, and then press the E button. The
4 5 button : Stops a track. Selection Play screen appears.
Skip : During playback, press the 1 or 2 button 3 . Use the ▲▼ buttons to select a track, and
5 to move to the previous or next music of listed.
then press the E button. A check appears
to the left of the track.
NUMBER buttons : During Playlist playback, press
6 the desired track number. The selected track is 4 . Repeat Step 3 to select and check additional
played. tracks.
5 . To remove a track from the list, move to the
Repeating Tracks on an Audio CD track, and then press the E button again.
The check on the track is removed.
You can set the product to repeat tracks on an 6 . When done, press the ► button to select
audio CD (CD-DA/MP3). Play, and then press the E button. The
1 . During playback, use the ► button to select Music Playback screen reappears listing only
in the lower right corner of the screen, the tracks you checked. The selected tracks
and then press the E button. play automatically.
2 . Use the ▲▼ to select the repeat mode you | NOTE |
want - Off, One Song, or All - and then  You can create a playlist with up to 99 tracks on Audio
press the E button. CDs (CD-DA).
 If you have created a playlist, Selection Play is replaced
by Edit Playlist on the Tools menu.
 On the Selection Play screen, you can also choose Select
All, Deselect All, and Cancel.
| 44 English

HT-E5400_ZA_0417-1(D2D).indd 44 2012-04-17 오후 6:46:17

 • Use Select All to select all tracks. This cancels | NOTE |
your individual track selections. When you press the  When Ripping is done, a folder called MP is created in the
RETURN (') button on your remote or select PLAY and USB.

05
then press the E button, all tracks will appear on the
Music Playback screen, and the product will begin to

Media Play
play all tracks from Track 001.
Playing Photo Contents
• Use Deselect All to deselect all selected tracks at once. You can play photo contents located on a DVD,
Then, select individual tracks or use Select All to select USB, mobile device or PC.
all the tracks, and then press the RETURN (') button
on your remote or select PLAY and then press the E Using the Tools Menu
button. If you do not use Select All or select individual During playback, press the TOOLS button.
tracks, the Playlist will not change.
• Cancel cancels any changes you made on the Play Go to Photos Select to go to the list of photos on the
Select screen. When you return to the Playback screen, List current media.
the Playlist will be unchanged. Start Slide
Select to start the slide show.
Show
Ripping
Slide Show
You can rip music from a music CD to a USB Select to set a slide show's speed.
Speed
device inserted in the USB jack.
Slide Show Select to set a slide show's special
1 . Insert a USB device into the USB jack on
Effect effects.
the front of the product, and then press the
RETURN (') button on your remote. Background Select to listen to music while viewing
2 . Insert the disc you want to rip from into the Music On a slide show.
product and close the disc tray.
Background Select to set the background music
3 . With the Playback screen displayed, press
Music Setting setting.
the TOOLS button. The Tools menu appears.
4 . Use the ▲▼ buttons to select Rip, and Select to set the picture settings.
then press the E button. The Rip screen - Dynamic : Choose to increase
appears. Sharpness.
5 . Use the ▲▼ buttons to select a track, and - Standard : Choose for most viewing
then press the E button. A check appears applications.
to the left of the track.
- Movie : This is the best setting for
6 . Repeat Step 5 to select and check additional
Picture Mode watching movies.
tracks.
7 . To remove a track from the list, move to the - User : Lets you adjust the sharpness
track, and then press the E button again. and noise reduction function
The check on the track is removed. respectively.
8 . When done, press the ► button to select | NOTE |
Rip, and then press the E button. The Rip
 When you use the BD wise function,
pop-up appears.
this menu will not appear.
9 . Press the E button to begin the ripping
process. The Ripping Completion Bar pop-up Select to enlarge the current picture.
Zoom
appears. (Enlarge up to 4 times)
10 . When ripping is complete, the “Ripping is
Select to rotate the picture. (This will
completed.” message appears. Press the
Rotate rotate the picture either clockwise or
E button.
counter clockwise.)
11 . Press the RETURN (') button to go back to
the Playback screen. Information Shows the picture information.

English 45 |

HT-E5400_ZA_0417-1(D2D).indd 45 2012-04-17 오후 6:46:22

 Media Play
| NOTE | Appears on the View function screen.
 Depending on the disc or storage device, the Tools menu Select to sort and then display all photo
Earliest Date
may differ. All options may not be displayed. or video files on a storage device from
 To enable the background music function, the photo file the earliest to latest date.
must be in the same storage media as the music file. Appears on the View function screen.
However, the sound quality can be affected by the bitrate Monthly Select to sort all photo or video files on
of the MP3 file, the size of the photo, and the encoding a storage device by the month created.
method.
Selection Play lets you select specific
 You can't enlarge the subtitle and PG graphic in the full
music, video, and photo files to play.
screen mode.
It works essentially the same for all
media. The example below is for
Using the Tools Menu when a File photos.
is Highlighted 1. On the Thumbnail View screen,
highlight a photo, and then press
When a file is highlighted, press the TOOLS the TOOLS button on the remote.
button. 2. In the Tools menu, select Selection
Play, and then press the E
Select to access the sort options: Artist, button.
Genre, Monthly, Latest Date, etc. The
View 3. On the selection screen, use the
sort options that appear depend on the
▲▼◄► buttons to select a
storage and media type.
photo you want to view, and then
Appears in the View function screen. press the E button.
Folder view Select to display the folders on the A check mark appears to the left
storage device. of the picture.
Appears on the View function screen. 4. Repeat Step 3 for each photo you
Title Select to sort all photo or video files on want to view.
a storage device by title. Selection Play
5. To de-select a photo, highlight it,
and then press the E button.
Appears on the View function screen.
Select Artist to sort and then display 6. When done, use the ◄► buttons
Artist to select Play, and then press
all music tracks on a storage device by
artist. the E button. A slide show
containing the photos you selected
Appears on the View function screen. begins.
Select Album to sort and then display
Album 7. To pause the slide show, press the
all music tracks on a storage device by
album. E button once. To restart the
slide show, press the E button
Appears on the View function screen. again.
Select Genre to sort and then display
Genre 8. To stop the slide show, press the
all music tracks on a storage device by
RETURN (') button.
genre.
| NOTE |
Appears on the View function screen.
Select to sort and then display all photo  After the slide show begins, you can
Latest Date control the slide show by pressing
or video files on a storage device from
the latest to earliest date. the TOOLS button and displaying
the Slide Show menu. See " Using
the Tools Menu" page 45.

| 46 English

HT-E5400_ZA_0417-1(D2D).indd 46 2012-04-17 오후 6:46:22

 Select Send to upload selected files • Select Create New, and then press
to Picasa, Facebook, Cloud Storage, N the E button. On the keyboard
Drive, or Family Story. pop-up that appears, create a name

05
To use Send, you need to establish an for the new playlist. Enter numbers

Media Play
account with the on-line site, and then using the numbers on the remote.
log in using the Log In function. Enter letters by using the ▲▼◄►
buttons to move the cursor, and
1. Use the ▲▼◄► buttons to then pressing the E button.
select a file, and then press the When finished, move to DONE at
E button. the bottom of the screen, and then
2. Repeat for each track or file you press the E button.
Send want to upload.
Depending on the screen you are
| NOTE | viewing, select Delete to erase a file
 You can also move to Select All on Delete (Playlist)
from erasable media (such as a USB
the right, and then press the E device) or to delete a playlist.
button to select all tracks or files.
Select Edit Playlist to remove files or
3. Select Send on the right side, and
tracks from an existing playlist. The
then press the E button.
storage device containing the playlist
4. Use the ▲▼ buttons to select the
must be inserted into or attached to
on line site you want to upload the
files or tracks to, and then press the product.
the E button. 1. Use the ▲▼◄► buttons to
The Log In/Out function lets you log in select a file, and then press the
Login / Out E button.
to your online Samsung account. Edit Playlist
2. Repeat for each track or file you
Select to create a playlist or add files want to remove.
or tracks to a playlist.
| NOTE |
1. Select Add to Playlist, and then
press the E button.  You can also move to Select All on
the right, and then press the E
2. Use the ▲▼◄► buttons to button to select all tracks or files.
highlight a track or file, and then
press the E button. 3. Select Remove on the right side,
and then press the E button.
3. Repeat for each track or file you
Add to Playlist want to add. After you have sorted by Artist, Genre,
4. Select Add on the right, and then Album,Title, Latest Date, Earliest Date,
press the E button. or Monthly, select a group that is the
Play Current
result of the sort (for example, all
5. On the screen that appears, Group
pictures taken in August), and then
perform one of the following
select Play Current Group to play or
actions:
view the files in that group only.
• Select the Playlist to which you want
to add the tracks or files and then Select to go to the Playlist section of
Go to Playlist
press E button. the Main AllShare screen.

English 47 |

HT-E5400_ZA_0417-1(D2D).indd 47 2012-04-17 오후 6:46:22

 Media Play
Encoding - which changes by language Presetting Stations
or by geographical area - modifies
Example : Presetting FM 89.10 into memory.
how the product sorts, arranges, and
Encoding presents files or tracks, displays dates, 1 . Press the FUNCTION button to select FM.
etc. Select Encoding to change the 2 . Press the TUNING/CH (,.) button to
encoding to match your language or select <89.10>.
geographical area.
3 . Press the TUNER MEMORY button.
Displays media file and content • NUMBER flashes on the display.
Information
information.
4 . Press the TUNER MEMORY button again.
| NOTE | • Press the TUNER MEMORY button before
NUMBER disappears from the display on its
 Depending on the disc or storage device, the Tools menu
own.
may differ. All options may not be displayed.
• After you press the TUNER MEMORY
button, NUMBER disappears from the
Listening to Radio display and the station is stored in memory.
5 . To preset another station, repeat steps 2 to 4.
Using Buttons on the Remote Control • To tune in to a preset station, press the
TUNING/CH (,.) button.
1 . Press the FUNCTION button to select FM.
2 . Tune in to the desired station.
• Preset Tuning 1 : Press the 5 button Using the Special Effects Remote
to select PRESET and then press the Control Buttons
TUNING/CH (,.) button to select the
preset station.
SOUND
- Before you can tune to preset stations, SOUND EFFECT Function
you must add preset stations to the EFFECT
product's memory.
• Manual Tuning : Press the 5 button Lets you select a mode that optimizes the sound.
to select MANUAL and then press the 1. Press the SOUND EFFECT button.
TUNING/CH (,.) button to tune in to a 2. Press the ▲▼ button to select the desired mode:
lower or higher frequency. DSP, Dolby Pro Logic II or SFE Mode.
• Automatic Tuning : Press the 5 button 3. Press the ◄► buttons to select the desired sound
to select MANUAL and then press and effect.
hold the TUNING/CH (,.) button to
automatically search the band.  DSP
MP3 Enhancer  Power Bass  Virtual 7.1 Off
Setting Mono/Stereo
• MP3 Enhancer : Helps enhance your sound experience
Press the MO/ST button. (ex. mp3 music). You can upscale your MP3 level sound
• Each time the button is pressed, the sound (24 kHz, 8bit) to CD level sound (44.1 kHz, 16bit).
switches between STEREO and MONO. • Power Bass : Increases the volume level of bass tones
• In a poor reception area, select MONO for a and provides thudding sound effects.
clear, interference-free broadcast. • Virtual 7.1 : Applies the 7.1 CH sound effect using the
5.1 CH speaker system.
• Off : Select this for normal listening.

| 48 English

HT-E5400_ZA_0417-1(D2D).indd 48 2012-04-17 오후 6:46:23

  Dolby Pro Logic II
Movie  Music  Game  Matrix  Prologic  Off Playing a 2D video in 3D mode

05
• Movie : Adds realism to a movie soundtrack.

Media Play
• Music : When listening to music, you can experience You can enjoy an ordinary 2D video in 3D mode.
sound effects as if you are listening to the actual
| NOTE |
performance.
 If you move to the Home or Smart Hub Home menu in
• Game : Enhances the excitement of the game’s sound.
3D mode, it will switch to 2D automatically.
• Matrix : Select to hear multi channel surround sound.
• Prologic : Select to listen to a 2CH sound source in
5.1CH surround sound with all speakers active.
- A specific speaker(s) may not output depending on
the input signal.
• Off : Select this for normal listening.

 SFE Mode
Symphony Hall in Boston (Hall 1)  Philharmonic
Hall in Bratislava (Hall 2)  Jazz Club in Seoul B 
Church in Seoul  Amphitheater (Rock)  Off
• Symphony Hall in Boston (Hall 1) : Provides a clear
vocal as if listening in a concert hall.
• Philharmonic Hall in Bratislava (Hall 2) : Also
provides a clear vocal as if listening in a concert hall
but, less powerful than HALL1.
• Jazz Club in Seoul B : Recommended setting for Jazz.
• Church in Seoul : Gives the feel of being in a grand
church.
• Amphitheater (Rock) : Recommended setting for
Rock.
• Off : Select this for normal listening.

3D Sound

You can enjoy more natural and vivid surround sound

with enriched tones by adjusting the depth of sound
using the level options.
Off  High  Medium  Low
| NOTE |
 It is not available in FM mode.

English 49 |

HT-E5400_ZA_0417-1(D2D).indd 49 2012-04-17 오후 6:46:23

 Network Services
You can enjoy various network services such as Smart Hub at a Glance
Smart Hub or BD-LIVE by connecting the product
to your network. 1 2 34
To use network services, you must first: Search

1 . Connect the product to the network.

(See page 22)
2 . Configure the network settings. Samsung Apps Your Video Family Story Fitness Kids

0 5 6 7
(See pages 31~34)
9 Contents 1

xxxxxxxx
Contents 2

xxxxxxxx
Contents 3

xxxxxxxx
Contents 4

xxxxxxxx

Using Smart Hub

Using Smart Hub, you can download movies,
a Login b WallPaper / Tools ' Return 8
videos, and music from the Internet, and access
various for pay or free-of-charge applications Your Video : Provides recommendations for videos
1
and view them on your TV. Application content based on your tastes.
includes news, sports, weather forecasts, stock Search : Provides an integrated search of your
market quotes, maps, photos, and games. 2
video providers and connected AllShare devices.
For instructions that explain how to use Smart
Hub, follow these steps: Recommended : Displays recommended contents
3
managed by Samsung.
1 . Go to www.samsung.com.
Commercial : Displays the Smart Hub Guide, an
2 . Click Support at the top of the page.
4 introduction to the product, and new application
3 . On the Support page, enter the model introductions.
number of your product into the Model
Number field. Family Story : An effortless way to access family
content.
4 . On the page that appears, click Get 5
• Provides access to family photos, messages, and
downloads on the left side under Downloads.
events, anytime and anywhere.
The Download Center appears.
5 . On the Download Center page, click the Fitness : Gateway to the Unified Self-Care Service.
Manuals tab. • Presents fitness videos from various content
6
6 . On the Manuals tab, click the file icon to the partners with feedback on calories burned after
right of Smart Hub Users Manual. The manual every workout.
downloads. Kids : Kids service gives kids an easy and safe way
to enjoy their favorite content.
| NOTE | 7
• Provides a wide variety of fun and safe content
 The web location of the Smart Hub manual is subject to for children.
change without notice.
Navigation Help : Displays the remote control
buttons you can use to navigate in Smart Hub.
• RED (A) : To log in to Smart Hub.
8
• GREEN (B) : To display the background screen.
• Tools : To display the settings window.
• Return : To return to the previous menu.

| 50 English

HT-E5400_ZA_0417-1(D2D).indd 50 2012-04-17 오후 6:46:23

 My Applications : Displays your personal gallery Web Browser at a Glance
9 of applications which you can add to, modify, and
1

06
delete.
Samsung Apps : Open Samsung Apps to download

Network Services
http://www.google.com/

0 various for pay or free-of-charge application

services.

Using the Web Browser

You can access the internet using the Web Google Search I’m Feeling Lucky

Browser application which is installed in the Smart

Hub screen by default.
1 . Select Smart Hub on the Home screen, and b Control Panel  Link Browsing / Tools ' Exit
2
then press the E button.
2 . Select the Web Browser application in Smart Control Panel : Displays the various Web Browser
Hub, and then press the E button. functions.
• : Moves to the previous page.
| NOTE |
• : Moves to the last page before going back.
 When you run the Web Browser with the product
• : Reloads the current page so that it is
connected by HDMI to a BD Wise compatible TV - and BD
refreshed on the screen.
Wise is on - the browser is maximized to fill the screen
and the TV's resolution is set to the optimal resolution • : Moves to the Home screen of the Web
automatically. Browser.
• : Allows you to zoom in or out of the screen at
 The Web Browser is not compatible with Java
various percentages.
applications.
• : Allows you to bookmark specific pages so
 If you attempt to download a file, and the file can not be that you can move to them easily.
saved, an error message will appear. 1 • : Allows you to view the history of your visited
 The playback of Flash videos is not supported. pages by date, name, or frequency.
 E-commerce, for purchasing products online, is not • http://www.google.com/ : Allows you to enter a
supported. page address manually or select a page from the
 ActiveX is not supported. visited page list to move to that page.
• : Allows you to switch easily between
multiple, currently open Web Browser windows.
• : Allows you to search for information by
entering words.
• : Lets you share the current site with your
family group by sending a message.
• : Allows you to configure all settings for using
the Web Browser.

English 51 |

HT-E5400_ZA_0417-1(D2D).indd 51 2012-04-17 오후 6:46:24

 Network Services
Navigation Help : Displays the remote control Using Disc to Digital
buttons you can use to navigate in Web Browser.
• GREEN (B) : To display the Control Panel. Access your movie collection via cloud storage
anytime, any place without your DVD disc.
2 • YELLOW (C) : You can change the cursor to Link
Browsing mode or Pointer Browsing mode. Go to www.samsungsupport.com for more
detailed information.
• Tools : To display Tools window.
• Exit : To return to the previous menu. | NOTE |
 You can access the Disc to Digital function by pressing
the Disc2Digital button on your remote control.
BD-LIVE™
 Samsung may add additional applications for this feature
Once the product is connected to your network, in the future.
you can enjoy various movie-related service
contents available on BD-LIVE compliant discs.
1 . Attach a USB memory stick to the USB jack
on the front of the product, and then check
its remaining memory. The memory device
must have at least 1GB of free space to
accommodate the BD-LIVE services.
2 . Select Settings on the Home screen, and
then press the E button.
3 . Select Network, and then press the E
button.
4 . Select BD-Live Settings, and then press the
E button.
5 . Select BD Data Management, and then
press the E button.
6 . Select Select Device, and then press the
E button.
7 . Select USB, and then press the E button.
8 . Insert a Blu-ray Disc that supports BD-LIVE.
9 . Select an item from the list of BD-LIVE service
contents provided by the disc manufacturer.

| NOTE |
 The way you use BD-LIVE and the provided contents may
differ, depending on the disc manufacturer.

| 52 English

HT-E5400_ZA_0418-1(D2D).indd 52 2012-04-18 오전 11:45:19

 Appendix
Additional Information

07
Note

Appendix
HDMI OUT
• Certain HDMI output resolutions may not work, depending on your TV.
Connections • You must have an HDMI connection to enjoy videos with 3D technology.
• A long HDMI cable may cause screen noise. If this occurs, set HDMI Deep Color to Off in the
menu.
3D Settings
• For some 3D discs, to stop a movie during 3D playback, press the 5 button once. The movie
stops and the 3D mode option is de-activated.
To change a 3D option selection when you are playing a 3D movie, press the 5 button once.
The Blu-ray menu appears. Press the 5 button again, then select 3D Settings in the Blu-ray
menu.
• Depending on the content and the position of the picture on your TV screen, you may see vertical
black bars on the left side, right side, or both sides.
TV Aspect
• Depending on the disc type, some aspect ratios may not be available.
• If you select an aspect ratio and option which is different than the aspect ratio of your TV screen,
then the picture might appear to be distorted.
• If you select the 16:9 Original, your TV may display 4:3 Pillarbox (black bars on sides of
picture).
BD Wise (Samsung Products only)
• When BD Wise is on, the Resolution setting automatically defaults to BD Wise and BD Wise
Settings
appears in the Resolution menu.
• If the product is connected to a device that does not support BD Wise, you can not use the BD
Wise function.
• For proper operation of BD Wise, set the BD Wise option in both the product and the TV to On.
Digital Output
• Be sure to select the correct Digital Output or you will hear no sound or just loud noise.
• If the HDMI device (AV receiver, TV) is not compatible with compressed formats (Dolby digital,
DTS), the audio signal outputs as PCM.
• Regular DVDs do not have BONUSVIEW audio and Navigation Sound Effects.
• Some Blu-ray Discs do not have BONUSVIEW audio and Navigation Sound Effects.
• This Digital Output setup does not affect the analog (L/R) audio or HDMI audio output to your TV.
It affects the optical and HDMI audio output when your product is connected to an AV receiver.
• If you play MPEG audio soundtracks, the audio signal outputs as PCM regardless of your Digital
Output selections (PCM or Bitstream).
BD-LIVE Internet Connection
• The Internet connection may be restricted while you are using BD-LIVE contents.

English 53 |

HT-E5400_ZA_0417-1(D2D).indd 53 2012-04-17 오후 6:46:26

 Appendix
Anynet+ (HDMI-CEC)
• Depending on your TV, certain HDMI output resolutions may not work. Please refer to the user
manual of your TV.
• This function is not available if the HDMI cable does not support CEC.
• If your Samsung TV has an Anynet+ logo, then it supports the Anynet+ function.
BD Data Management
• In the external memory mode, disc playback may be stopped if you disconnect the USB device in
the middle of playback.
• Only those USB devices formatted in the FAT file system (DOS 8.3 volume label) are supported.
We recommend you use USB devices that support USB 2.0 protocol with 4 MB/sec or faster
read/write speed.
• The Resume Play function may not work after you format the storage device.
• The total memory available to BD Data Management may differ, depending on the conditions.
Front Display
Settings
• You cannot change the brightness of the button and the VOL +, - button.
Speaker Settings
• When Speaker Selection is selected to TV Speaker, audio is produced through TV Speakers.
HDMI audio
• When HDMI audio output to the TV speaker, it is automatically down-mixed to 2 channels.
Audio Return Channel
• When Anynet+ (HDMI-CEC) is Off, the Audio Return Channel function is not available.
• Using an HDMI cable not certified for ARC (Audio Return Channel) may cause a compatibility
problem.
• The ARC function is only available if an ARC-compliant TV is connected.
Digital Output
• Digital Output can be activated when Speaker Selection is selected to TV Speaker.
Playing a Video files
• Video files with high bitrates of 20Mbps or more strain the product’s capabilities and may stop
playing during playback.
Selecting the Audio Language
Playback • The ◄► indicator will not appear on the screen if the BONUSVIEW section does not contain any
BONUSVIEW audio settings.
• The languages available through the Audio Language function depend on the languages that are
encoded on the disc. This function or certain languages may not be available.
• Some Blu-ray Discs may allow you to select either the PCM or Dolby digital audio soundtrack in
English.

| 54 English

HT-E5400_ZA_0417-1(D2D).indd 54 2012-04-17 오후 6:46:27

 Selecting the Subtitle Language
• Depending on the Blu-ray Disc / DVD, you may be able to change the subtitle language in the

07
Disc Menu. Press the DISC MENU button.
• This function depends on the selection of subtitles that are encoded on the disc and may not be

Appendix
available on all Blu-ray Discs/DVDs.
Playback • Information about the main feature BONUSVIEW mode will also appear if the Blu-ray Disc has a
BONUSVIEW section.
• This function changes both the primary and secondary subtitles at the same time.
• The total number of primary and secondary subtitles are displayed respectively.
Playing a JPEG files
• You can’t enlarge the subtitle and PG graphic in the full screen mode.
Dolby Pro Logic II Mode
• Before selecting Dolby Pro Logic II mode, connect your external device to the AUDIO INPUT jacks
(L and R) on the product. If you connect to only one of the inputs (L or R), you cannot listen to
surround sound.
Using the TOOLS button while playing pictures
• If the system is connected to a BD Wise compliant TV that has set BD Wise to On, the Picture
Settings menu will not appear.
• The Background Music function will not work unless the music file and the photo file are located
on the same storage media. Also, sound quality can be impacted by the bitrate of the MP3 music
file, the size of the photos, and the encoding method.
Playing back a USB Storage Device
• You must remove the USB storage device safely (by performing the “Safely Remove USB”
function) to prevent possible damage to the USB memory. Press the HOME button to move to the
AllShare Play Home menu, select the YELLOW (C) button, and then press the E button.
Playing Music
• Adjust the volume to a moderate level before you connect your iPod to the product.
• When the product is on and you connect an iPod, the product will charge the iPod's battery.
Watching a Movie
• You must have the VIDEO output (Composite) connected to your TV to view iPod video (See page
20).
• If you want to play iPod video via VIDEO output, set Anynet+ (HDMI-CEC) to off.
• Only the playback screen will appear on the TV. View other iPod screens on the iPod player.
• If you want to return to the iPod menus while the iPod player is connected using the dock, press
FUNCTION on the remote control or press on the front panel of the system and select
R. IPOD.
The Function mode switches as follows :
BD/DVD  D. IN  AUX  R. IPOD  HDMI1  HDMI2  FM

English 55 |

HT-E5400_ZA_0417-1(D2D).indd 55 2012-04-17 오후 6:46:27

 Appendix
iPod/iPhone Models You Can Use with This Product
• The volume control may not operate normally with iPod and iPhone models not listed on page
38. If you have a problem with any of the models listed above, please update the software of the
iPod/iPhone to the lastest version.
• Depending on the software version of the iPod, control problems may occur. This is not a
malfunction of the Home Theater.
iPod • Depending on the software version or the type of iPod, some operations may differ. Install the
latest iPod software. (recommended)
• You can enjoy music or videos through the Blu-ray/DVD disc function and enjoy music, videos
through the Remote iPod function. You need to use the iPod Dock to enjoy videos.
• Playback of applications' contents through the product is not guaranteed. We recommend
playing contents downloaded to the iPod.
• If you have a problem using your iPod, please visit www.apple.com/support/ipod.

| 56 English

HT-E5400_ZA_0417-1(D2D).indd 56 2012-04-17 오후 6:46:27

 Resolution according to the output mode
 Blu-ray Disc/E-contents/Digital Contents playback

07
HDMI/connected HDMI/not connected

Appendix
Output HDMI Mode
Setup E-contents/ VIDEO Mode VIDEO Mode
Blu-ray Disc
Digital contents
Resolution of Blu-
BD Wise 1080p@60F 480i -
ray Disc
Max. Resolution of Max. Resolution of TV
Auto 480i -
TV input input
1080p@60F 1080p@60F 1080p@60F 480i -
Movie Frame : Auto
1080p@24F 1080p@24F 480i -
(24Fs)
1080i 1080i 1080i 480i 480i
720p 720p 720p 480i 480i
480p 480p 480p 480i 480i
480i - - - 480i

 DVD playback

Output HDMI/connected HDMI/not connected

Setup HDMI Mode VIDEO Mode VIDEO Mode
BD Wise 480i 480i -
Auto Max. Resolution of TV input 480i -
1080p@60F 1080p@60F 480i -
1080i 1080i 480i 480i
720p 720p 480i 480i
480p 480p 480i 480i
480i - - 480i

English 57 |

HT-E5400_ZA_0417-1(D2D).indd 57 2012-04-17 오후 6:46:28

 Appendix
Digital Output Selection

Bitstream
Bitstream Bitstream
Setup PCM (Re-encoded
(Unprocessed) (Re-encoded DTS)
Dolby D)
Connection HDMI supported AV receiver
Re-encoded
PCM Up to PCM 7.1ch PCM DTS re-encoded
Dolby Digital *
Re-encoded
Dolby Digital Up to PCM 7.1ch Dolby Digital DTS re-encoded
Dolby Digital *
Dolby Digital Re-encoded
Up to PCM 7.1ch Dolby Digital Plus DTS re-encoded
Plus Dolby Digital *
Audio Stream Re-encoded
Dolby TrueHD Up to PCM 7.1ch Dolby TrueHD DTS re-encoded
on Blu-ray Dolby Digital *
Disc Re-encoded
DTS Up to PCM 6.1ch DTS DTS re-encoded
Dolby Digital *
DTS-HD High
DTS-HD High Re-encoded
Resolution Up to PCM 7.1ch DTS re-encoded
Resolution Audio Dolby Digital *
Audio
DTS-HD Re-encoded
Up to PCM 7.1ch DTS-HD Master Audio DTS re-encoded
Master Audio Dolby Digital *
PCM PCM 2ch PCM 2ch PCM 2ch PCM 2ch
Audio Stream
Dolby Digital Up to PCM 5.1ch Dolby Digital Dolby Digital Dolby Digital
on DVD
DTS Up to PCM 6.1ch DTS DTS DTS

Outputs only the main Decodes the main

Decodes the main feature audio stream feature audio and
Decodes the main feature
feature audio and so that your AV BONUSVIEW audio
audio and BONUSVIEW
BONUSVIEW audio receiver can decode stream together into
Definition for audio stream together
Any stream together into the audio bitstream. PCM audio and adds
into PCM audio and adds
Blu-ray Disc PCM audio and adds You will not hear Navigation Sound
Navigation Sound Effects,
Navigation Sound BONUSVIEW audio Effects, then re-
then re-encodes the PCM
Effects. or Navigation Sound encodes the PCM
audio into DTS bitstream.
Effects. audio into Dolby digital
bitstream or PCM.
* If the Source Stream is 2ch or mono, “Re-encoded Dolby D” Setting are not applied. Output will be
PCM 2ch.
Blu-ray Discs may include three audio streams :
- Main Feature Audio : The audio soundtrack of the main feature.
- BONUSVIEW audio : An additional soundtrack such as the director or actor’s commentary.
- Navigation Sound Effects : When you choose some menu navigation, Navigation Sound Effects may
sound. Navigation Sound Effects are different on each Blu-ray Disc.

| 58 English

HT-E5400_ZA_0417-1(D2D).indd 58 2012-04-17 오후 6:46:28

 Troubleshooting
Refer to the table below when this product does not function properly. If the problem you are

07
experiencing is not listed below or if the instructions below do not help, turn off the product, disconnect
the power cord, and contact Samsung Electronics at 1-800-SAMSUNG (1-800-726-7864).

Appendix
Symptom Check/Remedy
• Is the power cord plugged securely into the outlet?
I cannot eject the disc.
• Turn off the power and then turn it back on.
• Check the condition of the iPod connector and Dock.
The iPod fails to connect.
• Keep the iPod software version up to date.
• Check the region number of the Blu-ray/DVD disc.
Blu-ray/DVD disc purchased from abroad may not be playable.
Playback does not start.
• CD-ROMs and DVD-ROMs cannot be played on this product.
• Make sure that the rating level is correct.
Playback does not start
immediately when the • Are you using a deformed disc or a disc with scratches on the surface?
Play/Pause button is • Wipe the disc clean.
pressed.
Sound is not produced. • The home theater does not play sound during fast playback, slow playback,and step motion
playback.
• Are the speakers connected properly? Is the speaker setup correctly customized?
• Is the disc severely damaged?
Sound can be heard only • On certain Blu-ray/DVD discs, sound is output from the front speakers only.
from a few speakers and not • Check if the speakers are connected properly.
all 6. • Adjust the volume.
• When listening to a CD, radio or TV, sound is output to the front speakers only.
Dolby Digital 5.1 CH • Is there "Dolby Digital 5.1 CH" mark on the disc? Dolby Digital 5.1 CH Surround Sound is
Surround Sound is not produced only if the disc is recorded with 5.1 channel sound.
produced. • Is the audio language correctly set to Dolby Digital 5.1-CH in the information display?
The remote control does not • Are you operating the remote within its operational range and within the proper angle relative to
work. the sensor?
• Are the batteries drained?
• Have you selected the mode (TV/BD) functions of the remote control (TV or BD) correctly?
• The disc is rotating but no • Is the TV power on?
picture is produced. • Are the video cables connected properly?
• Picture quality is poor and • Is the disc dirty or damaged?
picture is shaking. • A poorly manufactured disc may not be playable.
Audio language and subtitles • Audio language and subtitles will not work if the disc does not contain them.
do not work.

English 59 |

HT-E5400_ZA_0417-1(D2D).indd 59 2012-04-17 오후 6:46:28

 Appendix
Symptom Check/Remedy
The menu screen does not • Are you using a disc that does not contain menus?
appear even when the menu
function is selected.
• You can play 16:9 Blu-ray/DVD discs in 16:9 Full mode, 4:3 Letter Box mode, or
The aspect ratio cannot be
4:3 Pan-Scan mode, but 4:3 Blu-ray/DVD discs are played in 4:3 ratio only. Refer to the
changed.
Blu-ray Disc jacket and then select the appropriate function.
• The product is not working. • Press and hold the remote control's 5 button for 5 seconds in STANDBY mode.
(Example: The power goes - Using the RESET function will erase all stored settings.
out or a strange noise is Do not use this unless necessary.
heard.)
• The Product is not working
normally.
You have forgotten the rating • With no disc in the product, press and hold the product's 5 button for longer than 5
level password. seconds. INIT appears on the display and all settings will return to the default values.
Then, press the POWER button.
- Using the RESET function will erase all stored settings.
Do not use this unless necessary.
Can't receive radio • Is the antenna connected properly?
broadcasts. • If the antenna's input signal is weak, install an external FM antenna in an area with
good reception.
While listening to TV audio • If the OPEN/CLOSE ^ button is pressed while listening to TV audio using the D. IN or
through the Product, no AUX functions, the Blu-ray/DVD disc functions are turned on and the TV audio is muted.
sound is heard.
"Not Available" appears on • The features or action cannot be completed at this time because:
screen. 1. The Blu-ray/DVD disc's software restricts it.
2. The Blu-ray/DVD disc's software doesn’t support the feature (e.g., angles)
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search time that is out of range.
If the HDMI output is set to a • Press and hold the 5 button on front panel for more than 5 seconds with no disc
resolution your TV cannot inserted. All settings will revert to the factory settings.
support (for example, 1080p),
you may not see a picture on
your TV.
No HDMI output. • Check the connection between the TV and the HDMI jack of the product.
• Check if your TV supports 480p/720p/1080i/1080p HDMI input resolution.
Abnormal HDMI output • If random noise appears on the screen, it means that TV does not support HDCP (High-
screen. bandwidth Digital Content Protection).

| 60 English

HT-E5400_ZA_0417-1(D2D).indd 60 2012-04-17 오후 6:46:29

 Symptom Check/Remedy
AllShare Play function

07
I can see folders shared • AllShare Play shows only files corresponding to the Photo, Music, and Movie categories.

Appendix
through AllShare Play, Files that do not correspond to these categories may not be displayed.
but I cannot see the files.
Video is played intermittently. • Check if the network is stable.
• Check if the network cable is properly connected and if the network is not overloaded.
• The wireless connection between the server and the product is unstable.
Check the connection.
The AllShare Play connection • IP address under the same subnetwork should be unique, otherwise IP collision can
between the TV and PC is results in such a phenomenon.
unstable. • Check if you have a firewall enabled.
If so, disable the firewall function.
BD-LIVE
I cannot connect to the • Test whether the network connection is successful by using the Network Status
BD-LIVE server. function.
• Check whether a USB memory device is connected to the product.
• The memory device must have at least 1GB of free space to accommodate the BD-LIVE
service.
You can check the available size in BD Data Management. (See page 54)
• See if the BD-LIVE Internet Connection option is set to Allow(All).
• If all above fails, contact the contents provider or update to the latest firmware.
When using the BD-LIVE • The memory device must have at least 1GB of free space to accommodate the BD-LIVE
service, an error occurs. service.
You can check the available size in BD Data Management. (See page 54)

| NOTE |
 When the factory default settings are restored, all stored user BD data will be deleted.

Repairs
If you contact us to repair your product, an administration fee may be charged if either:
1. An engineer is called out to your home at your request and there is no defect in the product.
2. You bring the unit to a repair center and there is no defect in the product.
We will provide you with the amount of the administration fee before we make a home visit or begin
any work on your product.
We recommend you read this manually thoroughly, search for a solution on line at www.samsung.
com, or contact Samsung Customer Care at 1-800-SAMSUNG (726-7864) before seeking to repair
your product.

English 61 |

HT-E5400_ZA_0417-1(D2D).indd 61 2012-04-17 오후 6:46:29

 Appendix
Specifications

Power Requirements AC 120V, 60Hz

Power Consumption 92.2 W
Weight 5.6 Ibs
General
Dimensions 16.9 (W) x 2.3 (H) x 10.1 (D) inches
Operating Temperature Range +41°F to +95°F
Operating Humidity Range 10 % to 75 %
Signal/noise ratio 55 dB
FM Tuner Usable sensitivity 12 dB
Total harmonic distortion 0.5 %
BD (Blu-ray Disc) Reading Speed : 9.834 m/sec
Reading Speed : 6.98 ~ 7.68 m/sec.
DVD (Digital Versatile Disc)
Approx. Play Time (Single Sided, Single Layer Disc) : 135 min.
Disc Reading Speed : 4.8 ~ 5.6 m/sec.
CD : 5 inches (COMPACT DISC)
Maximum Play Time : 74 min.
Reading Speed : 4.8 ~ 5.6 m/sec.
CD : 3 1/2 inches (COMPACT DISC)
Maximum Play Time : 20 min.
1 channel : 1.0 Vp-p (75 Ω load)
Video Output Composite Video
Blu-ray Disc : 480i DVD : 480i
1080p, 1080i, 720p, 480p
Video/Audio HDMI
PCM multichannel audio, Bitstream audio, PCM audio
Front speaker output 165W x 2(3Ω)
Center speaker output 170W(3Ω)
Surround speaker output 165W x 2(3Ω)
Subwoofer speaker output 170W(3Ω)
Amplifier Analog input 20Hz~20kHz (±3dB)
Frequency response
Digital input 20Hz~40kHz (±4dB)
S/N Ratio 70dB
Channel separation 60dB
Input sensitivity (AUX)500mV

| 62 English

HT-E5400_ZA_0417-1(D2D).indd 62 2012-04-17 오후 6:46:29

 5.1ch speaker system
Speaker system
Front Surround Center Subwoofer

07
Impedance 3Ω 3Ω 3Ω 3Ω

Appendix
Frequency range 140Hz~20kHz 140Hz~20kHz 140Hz~20kHz 40Hz ~ 160Hz
Output sound pressure
87dB/W/M 87dB/W/M 87dB/W/M 88dB/W/M
level
Speaker Rated input 165W 165W 170W 170W
Maximum input 330W 330W 340W 340W
Front : 3.54 x 5.57 x 2.69 inches
Dimensions Surround : 3.54 x 5.57 x 2.69 inches
(W x H x D) Center : 14.17 x 2.93 x 2.69 inches
Subwoofer : 6.61 x 13.78 x 11.22 inches
Front : 1.34 Ibs, Surround : 1.34 Ibs
Weights
Center : 1.94 Ibs, Subwoofer : 8.09 Ibs
• Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
• Weight and dimensions are approximate.
• Design and specifications are subject to change without prior notice.
• Dispose unwanted electronics through an approved recycler.
To find the nearest recycling location, go to our website: www.samsung.com/recyclingdirect or call, (877)
278 - 0799

English 63 |

HT-E5400_ZA_0417-1(D2D).indd 63 2012-04-17 오후 6:46:30

 LIMITED WARRANTY TO ORIGINAL PURCHASER
This SAMSUNG brand product, as supplied and distributed by SAMSUNG and delivered new, in the original carton to the original
consumer purchaser, is warranted by SAMSUNG against manufacturing defects in materials and workmanship for a limited
warranty period of:
One (1) Year Parts and Labor*
(*90 Days Parts and Labor for Commercial Use)

This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the United
States. To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service procedures.
Warranty service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale must be
presented upon request as proof of purchase to SAMSUNG or SAMSUNG's authorized service center. Transportation of the
product to and from the service center is the responsibility of the purchaser.

SAMSUNG will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts
or products if found to be defective during the limited warranty period specified above. All replaced parts and products become
the property of SAMSUNG and must be returned to SAMSUNG. Replacement parts and products assume the remaining original
warranty, or ninety (90) days, whichever is longer.

SAMSUNG’s obligations with respect to software products distributed by SAMSUNG under the SAMSUNG brand name are set
forth in the applicable end user license agreement. Non-SAMSUNG hardware and software products, if provided, are on an “AS
IS” basis.
Non-SAMSUNG manufacturers, suppliers, publishers, and service providers may provide their own warranties.

This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, and except to the
extent otherwise expressly provided for in this statement, noncommercial use of this product, and shall not apply to the following,
including, but not limited to: damage which occurs in shipment; delivery and installation; applications and uses for which this
product was not intended; altered product or serial numbers; cosmetic damage or exterior finish; accidents, abuse, neglect,
fire, water, lightning or other acts of nature; use of products, equipment, systems, utilities, services, parts, supplies, accessories,
applications, installations, repairs, external wiring or connectors not supplied and authorized by SAMSUNG, or which damage this
product or result in service problems; incorrect electrical line voltage, fluctuations and surges; customer adjustments and failure
to follow operating instructions, cleaning, maintenance and environmental instructions that are covered and prescribed in the
instruction book; product removal or reinstallation; reception problems and distortion related to noise, echo, interference or other
signal transmission and delivery problems. SAMSUNG does not warrant uninterrupted or error-free operation of the product.

THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES
WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED
ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH
RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF
REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF
THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE
PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING
THE FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER AND
PURCHASER’S PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE, MISUSE OR INABILITY
TO USE THIS PRODUCT SOLD BY SAMSUNG NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS
LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT, IS
NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state.

To obtain warranty service, please contact SAMSUNG customer care center.

HT-E5400_ZA_0417-1(D2D).indd 64 2012-04-17 오후 6:46:30

 QUESTIONS OR COMMENTS?
COUNTRY CALL OR VISIT US ONLINE AT WRITE

Samsung Electronics America, Inc.

1-800-SAMSUNG
IN THE US www.samsung.com 85 Challenger Road Ridgefield Park,
(726-7864)
NJ 07660-2112

AH68-02446A-03

HT-E5400_ZA_0417-1(D2D).indd 65 2012-04-17 오후 6:46:30