UNIT-I

Amplitude Modulation System

1
 Introduction to communications

• Elements of a communication system (cont)

Basic components
 Transmitter
– Convert Source (information) to signals
– Send converted signals to the channel (by antenna if
applicable)
 Channel
– Wireless: atmosphere (free space)
– Wired: coaxial cables, twisted wires, optical fibre
 Receiver
– Reconvert received signals to original information
– Output the original information

Signal Carrier Transmission Medium Carrier Circuits Signal

Processing Circuits Processing
m(t)
mˆ (t )
s(t)
r(t)
TRANSMITTER CHANNEL RECEIVER

2
 Introduction to communications

• Elements of a communication system (cont)

Frequencies for communication
twisted coax cable optical transmission
pair

1 Mm 10 km 100 m 1m 10 mm 100 1 m
300 30 kHz 3 MHz 300 MHz 30 GHz m 300
Hz 3 THz THz

VLF LF MF HF VHF UHF SHF EHF infrared visible UV

light
 VLF = Very Low Frequency UHF = Ultra High Frequency
 LF = Low Frequency SHF = Super High
Frequency
 MF = Medium Frequency EHF = Extra High Frequency
 HF = High Frequency UV = Ultraviolet Light
 VHF = Very High Frequency

 Frequency and wave length:

 = c/f
wave length , speed of light c  3x108m/s, frequency f

3
 Baseband vs Passband Transmission

• Baseband signals:
– Voice (0-4kHz)
– TV (0-6 MHz)
• A signal may be sent in
its baseband format
when a dedicated wired
channel is available.
• Otherwise, it must be
converted to passband.

4
 Modulation: What and Why?
• The process of shifting the baseband signal to
passband range is called Modulation.
• The process of shifting the passband signal to
baseband frequency range is called Demodulation.
• Reasons for modulation:
– Simultaneous transmission of several signals
– Practical Design of Antennas
– Exchange of power and bandwidth

5
 Types of (Carrier) Modulation
• In modulation, one characteristic of a signal
(generally a sinusoidal wave) known as the carrier
is changed based on the information signal that we
wish to transmit (modulating signal).
• That could be the amplitude, phase, or frequency,
which result in Amplitude modulation (AM), Phase
modulation (PM), or Frequency modulation (FM).
The last two are combined as Angle Modulation

6
 Types of Amplitude Modulation (AM)
• Double Sideband with carrier (we will call it AM): This is
the most widely used type of AM modulation. In fact, all
radio channels in the AM band use this type of
modulation.
• Double Sideband Suppressed Carrier (DSBSC): This is the
same as the AM modulation above but without the
carrier.
• Single Sideband (SSB): In this modulation, only half of
the signal of the DSBSC is used.
• Vestigial Sideband (VSB): This is a modification of the
SSB to ease the generation and reception of the signal.

7
 Definition of AM
• Shift m(t) by some DC value “A”
such that A+m(t) ≥ 0. Or A ≥ mpeak

g AM (t )  [ A  m(t )] cos(C t )
 A cos(C t )  m(t ) cos(C t )
• Called DSBWC. Here will refer to it
as Full AM, or simply AM
• Modulation index m = mp /A.
• 0≤m≤1

8
 Spectrum of AM

1
g AM (t )  A (  C )   (  C )  M (  C )  M (  C )
2

9
 Generation of AM
• AM signals can be generated by any DSBSC
modulator, by using A+m(t) as input instead of
m(t).
• In fact, the presence of the carrier term can
make it even simpler. We can use it for
switching instead of generating a local carrier.
• The switching action can be made by a single
diode instead of a diode bridge.

10
 AM Generator

• A >> m(t)
(to ensure switching
at every period).
A

• vR=[cosct+m(t)][1/2 + 2/p(cosct-1/3cos3ct + …)]

=(1/2)cosct+(2/p)m(t) cosct + other terms (suppressed by BPF)
• vo(t) = (1/2)cosct+(2/p)m(t) cosct

11
AM Modulation Process (Frequency)

12
 AM Demodulation: Rectifier Detector
• Because of the presence of a carrier term in
the received signal, switching can be
performed in the same way we did in the
modulator.

13
Rectifier Detector: Time Domain

14
Rectifier Detector (Frequency
Domain)

15
 Envelope Detector

• When D is forward-biased, the capacitor charges and

follows input.
• When D is reverse-biased, the capacitor discharges
through R.

16
Double Sideband Suppressed Carrier (DSBSC)

DSBSC carrier is filtered or suppressed or receiver. That’s why it is called

DSBSC

Problem with DSBSC

1) Geometrical Carrier or Receiver
2) Phase Detection Problem
3) Frequency Shifting Properties

17
Time and Frequency Representation of DSBSC
Modulation Process

18
 DSBSC Demodulation

Double Sideband Suppressed Carrier (DSBSC)

For a broadcast system it is more economical to have one

experience high power transmitter and expensive receiver, for such
application a large carrier signal is transmitted along with the
suppressed carrier modulated signal m(t) Cos (wct), thus no need
to generate a local carrier. This is called AM in which the
transmitted signal is.

Cos wct [ A + m(t) ]

19
Time and Frequency Representation of DSBSC
Demodulation Process

20
 Modulator Circuits
• Basically we are after multiplying a signal with
a carrier.
• There are three realizations of this operation:
– Multiplier Circuits
– Non-Linear Circuits
– Switching Circuits

21
 Non-Linear Devices (NLD)
• A NLD is a device whose input-output relation is non-
linear. One such example is the diode (iD=ev /v ).
D T

• The output of a NLD can be expressed as a power series

of the input, that is
y(t) = ax(t) + bx2(t) + cx3(t) + …
• When x(t) << 1, the higher powers can be neglected, and
the output can be approximated by the first two terms.
• When the input x(t) is the sum of two signal, m(t)+c(t),
x2(t) will have the product term m(t)c(t)

22
 Non-Linear Modulators

x1 (t )  c(t )  m(t )  cos( C t )  m(t ) y1 (t )  acos(C t )  m(t )  bcos(C t )  m(t )

2

x1 (t )  c(t )  m(t )  cos( C t )  m(t )

 a cos(C t )  am(t )  bm 2 (t )  2bm(t )  cos(C t )  b cos 2 (C t )
b b
 am(t )  bm 2 (t )  2bm(t )  cos(C t )  a cos(C t )   cos(2C t )
    2 2 
Undesired Undesired Desired Undesired  
Undesired Undesired

y2 (t )  acos(C t )  m(t )  bcos(C t )  m(t )

2
z (t )  y1 (t )  y2 (t )
 2
am(t )  4bm(t )  cos( t )
 C  a cos(C t )  am(t )  bm 2 (t )  2bm(t )  cos(C t )  b cos 2 (C t )
Undesired Desired
b b
  am(t )  bm 2 (t )  2bm(t )  cos(C t )  a cos(C t )   cos(2C t )
    2 2 
Undesired Undesired Desired Undesired  
Undesired Undesired

23
 Switching Modulators
• Any periodic function can be expressed as a
series of cosines (Fourier Series).
• The information signal, m(t), can therefore be,
equivalently, multiplied by any periodic
function, and followed by BPF.
• Let this periodic function be a train of pulses.
• Multiplication by a train of pulses can be
realized by simple switching.

24
Switching Modulator Illustration

25
Switching Modulator: Diode Bridge

26
Switching Modulator: Ring

27
 Demodulation of DSBSC
• The modulator circuits can be used for demodulation, but
replacing the BPF by a LPF of bandwidth B Hz.
• The receiver must generate a carrier frequency in phase
and frequency synchronization with the incoming carrier.
• This type of demodulation is therefore called coherent
demodulation (or detection).
e(t) HLPF( )
gDSBSC(t) X BW = 2 B
f(t)

c(t)

DSBSC Demodulator (receiver)

28
 From DSBSC to DSBWC (AM)
• Carrier recovery circuits, which are required
for the operation of coherent demodulation,
are sophisticated and could be quite costly.
• If we can let m(t) be the envelope of the
modulated signal, then a much simpler circuit,
the envelope detector, can be used for
demodulation (non-coherent demodulation).
• How can we make m(t) be the envelope of the
modulated signal?

29
 Single-Side Band (SSB) Modulation

• DSBSC (as well as AM) occupies double the bandwidth

of the baseband signal, although the two sides carry
the same information.
• Why not send only one side, the upper or the lower?
• Modulation: similar to DSBSC. Only change the settings
of the BPF (center frequency, bandwidth).
• Demodulation: similar to DSBSC (coherent)

30
SSB Representation
How would we represent
the SSB signal in the time
domain?
gUSB(t) = ?
gLSB(t) = ?

31
 Time-Domain Representation of SSB (1/2)

M() = M+() + M-()

Let m+(t)↔M+() and m-(t)↔M-
()
Then: m(t) = m+(t) + m-(t) [linearity]
Because M+(), M-() are not even
 m+(t), m-(t) are complex.
Since their sum is real they must be
conjugates.
m+(t) = ½ [m(t) + j mh(t)]
m-(t) = ½ [m(t) - j mh(t)]
What is mh(t) ?

32
 Time-Domain Representation of SSB (2/2)

M() = M+() + M-()

M+() = M()u(); M-() = M()u(-)
sgn()=2u() -1  u()= ½ + ½ sgn(); u(-) = ½ -½ sgn()
M+() = ½[ M() + M()sgn()]
M-() = ½ [M() - M()sgn()]
Comparing to:
m+(t) = ½ [m(t) + j mh(t)] ↔ ½ [M() + j Mh()]
m-(t) = ½ [m(t) - j mh(t)] ↔ ½ [M() - j Mh()]
We find
Mh() = - j M()∙sgn() where mh(t)↔Mh()

33
 Hilbert Transform
• mh(t) is known as the Hilbert Transform (HT) of m(t).
• The transfer function of this transform is given by:
H() = -j sgn()

• It is basically a /2 phase shifter

34
 Hilbert Transform of cos(ct)
cos(ct) ↔  ( – c) + ( + c)]
HT[cos(ct)] ↔ -j sgn()  ( – c) + ( + c)]
= j sgn()  ( – c)  ( + c)]
= j  ( – c) + ( + c)]
= j  ( + c) - ( - c)] ↔ sin(ct)

Which is expected since:

cos(ct-/2) = sin(ct)

35
 Time-Domain Operation for Hilbert
Transformation
For Hilbert Transformation H() = -j sgn().
What is h(t)?
sgn(t) ↔ 2/(j) [From FT table]
2/(jt) ↔ 2 sgn(-) [symmetry]
1/( t) ↔ -j sgn()
Since Mh() = - j M()∙sgn() = H() ∙ M()
Then 1
mh (t )  * m (t )
t

1 m( )
  d
  t  

36
Finally …
gUSB (t )  m (t )e jC t  m (t )e j C t
g LSB (t )  m (t )e j C t  m (t )e jC t
1 1
gUSB (t )  m(t )e jC t  jmh (t )e jC t
2 2
1 1
 m(t )e  jC t  jmh (t )e  jC t
2 2
 m(t ) cos(C t )  mh (t ) sin(C t )
1 1
g LSB (t )  m(t )e jC t  jmh (t )e jC t
2 2
1 1
 m(t )e  jC t  jmh (t )e  jC t GUSB ( )  M  (  C )  M  (  C )
2 2
 m(t ) cos(C t )  mh (t ) sin(C t ) GLSB ( )  M  (  C )  M  (  C )

37
 Generation of SSB
• Selective Filtering Method
Realization based on spectrum analysis
• Phase-Shift Method
Realization based on time-domain expression
of the modulated signal

38
Selective Filtering

39
 Phase Shifting
gUSB (t )  m(t ) cos(C t )  mh (t ) sin(C t )
g LSB (t )  m(t ) cos(C t )  mh (t ) sin(C t ) m(t)cos( ct)
X
(a)

cos( ct)
(d)
m(t)
gSSB(t)
Phase Shifter
sin( ct) – /2 gUSB(t) if –
+ or –
gLSB(t) if +

(b) (c)
Phase Shifter
– /2 X
mh(t)sin( ct)

mh(t)

SSB Modulator

40
 Phase-shifting Method:
Frequency-Domain Illustration

41
 SSB Demodulation (Coherent)
g SSB (t )  m(t ) cos(C t )  mh (t ) sin(C t )
1 1
g SSB (t ) cos(C t )  m(t )[1  cos(2C t )]  mh (t ) sin(2C t )
2 2
1
LPF Output  m(t )
2

42
 FDM in Telephony
• FDM is done in stages
– Reduce number of carrier frequencies
– More practical realization of filters
• Group: 12 voice channels  4 kHz = 48 kHz
occupy the band 60-108 kHz
• Supergroup: 5 groups  48 kHz = 240 kHz
occupy the band 312-552
• Mastergroup: 10 S-G  240 kHz = 2400 kHz
occupy the band 564-3084 kHz

43
 FDM Hierarchy
108 k 552 k
12 5
11 4
10 3
9 2
8 1 312 k
7
6 Supergroup
5
4
3
2
1 60 k
4
0 Group

44
 Vestigial Side Band Modulation (VSB)
• What if we want to generate SSB using
selective filtering but there is no guard band
between the two sides?
We will filter-in a vestige of the other band.
• Can we still recover our message, without
distortion, after demodulation?
Yes. If we use a proper LPF.

45
 Filtering Condition of VSB
g DSBSC (t )  2m(t ) cos(C t )
G DSBSC ( )  M (   C )  M (   C )
GVSB ( )  H VSB ( )M (   C )  M (   C )
 
X ( )  H VSB (  C )  M (  2C )  M ( )
     
 at  2  C Baseband 

 
 H VSB (  C )  M ( )  M (  2C ) 
     
 baseband at  2 C 
Z ( )  H LPF ( )H VSB (  C )  H VSB (  C ) M ( )
1
H LPF ( )  ; || ≤ 2  B
H VSB (   C )  H VSB (   C )

46
VSB Filtering

47
 VSB Filter: Special Case
• Condition For distortionless demodulation:
1
H LPF ( )  ; || ≤ 2  B
H VSB (  C )  H VSB (  C )
• If we impose the condition on the filter at the modulator:

HVSB(-c) + HVSB(+c) = 1 ; || ≤ 2  B

Then HLPF = 1 for || ≤ 2  B (Ideal LPF)

• HVSB() will then have odd symmetry around c over the
transition period.

48
49
 AM Broadcasting
• Allocated the band 530 kHz – 1600 kHz (with
minor variations)
• 10 kHz per channel. (9 kHz in some countries)
• More that 100 stations can be licensed in the
same geographical area.
• Uses AM modulation (DSB + C)

50
 AM station Reception
• In theory, any station can be extracted from the stream of spectra by
tuning the receiver BPF to its center frequency. Then demodulated.

• Impracticalities:
– Requires a BPF with very high Q-factor (Q = fc / B).
– Particularly difficult if the filter is to be tunable.

51
 Angle Modulation – Frequency Modulation

Consider again the general carrier

vc t ) = Vc cosωc t + φc )
ωct+φc) represents the angle of the carrier.

There are two ways of varying the angle of the carrier.

a) By varying the frequency, c – Frequency Modulation.

b) By varying the phase, c – Phase Modulation

1
 Frequency Modulation

In FM, the message signal m(t) controls the frequency fc of the carrier. Consider
carrier
vc t ) = Vc cosωc t )

then for FM we may write:

FM signal vs t ) = Vc cos2π  f c + frequency deviation )t ) ,where the frequency deviation

will depend on m(t).
Given that the carrier frequency will change we may write for an instantaneous
carrier signal
Vc cos ωit ) = Vc cos 2πf i t ) = Vc cos φi )

= 2πf i t and fi is the instantaneous

ωi t=
where i is the instantaneous angle
frequency. 2
 Frequency Modulation

dφi 1 dφi
Since φi = 2πfit then dt
= 2πf i or fi =
2π dt

i.e. frequency is proportional to the rate of change of angle.

If fc is the unmodulated carrier and fm is the modulating frequency, then we may

deduce that
1 dφi
f i = f c + Δf c cosωm t ) =
2π dt

fc is the peak deviation of the carrier.

1 dφi dφi
Hence, we have = f c + Δf c cosωm t ) ,i.e. = 2πf c + 2πΔf c cosωm t )
2π dt dt

3
 Frequency Modulation

After integration i.e.  ω + 2πΔf cosω t ))dt

c c m

2πΔf csin ωmt )

φi = ωc t +
ωm
Δf c
φi = ωc t + sin ωmt )
fm

vs t ) = Vc cosφi )
Hence for the FM signal,

 Δf 
vs t ) = Vc cos ωc t + c sin ωmt )
 fm 
4
 Frequency Modulation

Δf c
The ratio is called the Modulation Index denoted by  i.e.
fm

Peak frequency deviation

β=
modulating frequency

Note – FM, as implicit in the above equation for vs(t), is a non-linear process
the principle of superposition does not apply. The FM signal for a message m(
band of signals is very complex. Hence, m(t) is usually considered as a 'single ton
modulating signal' of the form

mt ) = Vm cosωmt )

5
 Frequency Modulation

 Δf 
The equation vs t ) = Vc cos ωc t + c sin ωmt ) may be expressed as Bessel
 fm 
series (Bessel functions)

vs t ) = Vc  J  β )cosω + nω )t
n c m
n= 

where Jn() are Bessel functions of the first kind. Expanding the equation for a fe
terms we have:

v s (t )  Vc J 0 (  ) cos( c )t  Vc J 1 (  ) cos( c   m )t  Vc J 1 (  ) cos ( c   m )t

            
Amp fc Amp fc  f m Amp fc  f m

 Vc J 2 (  ) cos( c  2 m )t  Vc J  2 (  ) cos ( c  2 m )t  
     
Amp fc 2 f m Amp fc 2 f m
6
 FM Signal Spectrum.
The image cannot be display ed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart y our computer, and then open the file again. If the red x still appears, y ou may hav e to delete the image and then insert it again.

The amplitudes drawn are completely arbitrary, since we have not found any valu
Jn() – this sketch is only to illustrate the spectrum.
7
 Generation of FM signals – Frequency
Modulation.

An FM demodulator is:

• a voltage-to-frequency converter V/F

• a voltage controlled oscillator VCO

In these devices (V/F or VCO), the output frequency is dependent on the input vo
amplitude.

The image cannot be display ed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart y our computer, and then open the file again. If the red x still appears, y ou may hav e to delete the image and then insert it again.

8
 V/F Characteristics.

Apply VIN , e.g. 0 Volts, +1 Volts, +2 Volts, -1 Volts, -2 Volts, ... and measure th
frequency output for each VIN . The ideal V/F characteristic is a straight line as
shown below. The image cannot be display ed. Your computer may not hav e enough memory to open the image, or the image may hav e been corrupted. Restart y our computer, and then open the file again. If the red x still appears, y ou may hav e to delete
the image and then insert it again.

fc, the frequency output when the input is zero is called the undeviated or nomina
carrier frequency.
The image cannot be
display ed. Your computer

Δf may not hav e enough

memory to open the image,
or the image may hav e been
corrupted. Restart y our

The gradient of the characteristic is called the Frequency Conversion Factor

computer, and then open the
file again. If the red x still
appears, y ou may hav e to
delete the image and then
insert it again.

denoted by  per Volt.

ΔV
9
 V/F Characteristics.
mt ) = Vm cosωm t )
Consider now, an analogue message input,

As the input m(t) varies from

+Vm  0  Vm
the output frequency will vary from a
maximum, through fc, to a minimum
frequency.
10
 V/F Characteristics.

For a straight line, y = c + mx, where c = value of y when x = 0, m = gradient, h

we may say
f OUT = f c + αVIN

and when VIN = m(t)f OUT = f c + αmt ) ,i.e. the deviation depends on m(t).

Considering that maximum and minimum input amplitudes are +Vm and -Vm
respectively, then
f max = f c + αVm
on the diagram on the previous slide.
f min = f c  αVm

The peak-to-peak deviation is fmax – fmin, but more importantly for FM the peak
deviation fc is

Δf c = αVm Δf c αVm
Peak Deviation, β=
Hence, Modulation Index, =
fm fm
11
 Summary of the important points of FM

• In FM, the message signal m(t) is assumed to be a single tone frequency,

mt ) = Vm cosωmt )
• The FM signal vs(t) from which the spectrum may be obtained as

vs t ) = Vc  J  β )cosω + nω )t
n c m
n= 

Δf c αVm
where Jn() are Bessel coefficients and β
Modulation Index, f = f
=
m m

•  Hz per Volt is the V/F modulator, gradient

Frequency
or Conversion Factor,
 per Volt
•  is a measure of the change in output frequency for a change in input amplitud

Peak Deviation (of the carrier frequency from fc) Δf c = αVm

12
 FM Signal Waveforms.

The diagrams below illustrate FM signal waveforms for various inputs

At this stage, an input digital data

sequence, d(t), is introduced –
the output in this case will be FSK,
(Frequency Shift Keying).

13
 FM Signal Waveforms.

Assuming d (t )  V for 1' s f OUT  f1  f c  V for 1' s  the output ‘switches’


 V for 0' s f OUT  f 0  f c  V for 0' s  between f1 and f0.

14
 FM Signal Waveforms.

The output frequency varies ‘gradually’ from fc to (fc + Vm), through fc to

(fc - Vm) etc. 15
 FM Signal Waveforms.

If we plot fOUT as a function of VIN:

In general, m(t) will be a ‘band of signals’, i.e. it will contain amplitude and freque
variations. Both amplitude and frequency change in m(t) at the input are translat
(just) frequency changes in the FM output signal, i.e. the amplitude of the output
signal is constant.
Amplitude changes at the input are translated to deviation from the carrier at the
output. The larger the amplitude, the greater the deviation. 16
 FM Signal Waveforms.
Frequency changes at the input are translated to rate of change of frequency at
output.An attempt to illustrate this is shown below:

17
 FM Spectrum – Bessel Coefficients.

The FM signal spectrum may be determined from


v s (t )  V c J
n  
n (  ) cos( c  n m )t

The values for the Bessel coefficients, Jn() may be found from
graphs or, preferably, tables of ‘Bessel functions of the first ki

18
 FM Spectrum – Bessel Coefficients.

Jn()

 = 2.4 =5

In the series for vs(t), n = 0 is the carrier component, ) cos( c t ) , hence the
Vc J 0 ( i.e.
n = 0 curve shows how the component at the carrier frequency, fc, varies in ampl
with modulation index .
19
 FM Spectrum – Bessel Coefficients.
Hence for a given value of modulation index , the values of Jn() may be read of
graph and hence the component amplitudes (VcJn()) may be determined.

A further way to interpret these curves is to imagine them in 3 dimensions

20
 Examples from the graph

 = 0: When  = 0 the carrier is unmodulated and J0(0) = 1, all other J

 = 2.4: From the graph (approximately)

J0(2.4) = 0, J1(2.4) = 0.5, J2(2.4) = 0.45 and J3(2.4) = 0.2

21
 Significant Sidebands – Spectrum.
As may be seen from the table of Bessel functions, for values of n above a certain
value, the values of Jn() become progressively smaller. In FM the sidebands are
considered to be significant if Jn()  0.01 (1%).
Although the bandwidth of an FM signal is infinite, components with amplitudes
VcJn(), for which Jn() < 0.01 are deemed to be insignificant and may be ignored

Example: A message signal with a frequency fm Hz modulates a carrier fc to prod

FM with a modulation index  = 1. Sketch the spectrum.

n Jn(1) Amplitude Frequency

0 0.7652 0.7652Vc fc
1 0.4400 0.44Vc fc+fm fc - fm
2 0.1149 0.1149Vc fc+2fm fc - 2fm
3 0.0196 0.0196Vc fc+3fm fc -3 fm
4 0.0025 Insignificant
5 0.0002 Insignificant
22
 Significant Sidebands – Spectrum.

As shown, the bandwidth of the spectrum containing significa

components is 6fm, for  = 1.
23
 Significant Sidebands – Spectrum.
The table below shows the number of significant sidebands for various modulatio
indices () and the associated spectral bandwidth.
 No of sidebands  1% of Bandwidth
unmodulated carrier
0.1 2 2fm
0.3 4 4fm
0.5 4 4fm
1.0 6 6fm
2.0 8 8fm
5.0 16 16fm
10.0 28 28fm
e.g. for  = 5,
16 sidebands
(8 pairs).

24
 Carson’s Rule for FM Bandwidth.

An approximation for the bandwidth of an FM signal is given

BW = 2(Maximum frequency deviation + highest modulated
frequency)

Bandwidth  2(f c  f m ) Carson’s Rule

25
 Narrowband and Wideband FM

Narrowband FM NBFM

From the graph/table of Bessel functions it may be seen that for small , ( 
there is only the carrier and 2 significant sidebands, i.e. BW = 2fm.

FM with   0.3 is referred to as narrowband FM (NBFM) (Note, the bandwidth i

the same as DSBAM).

Wideband FM WBFM

For  > 0.3 there are more than 2 significant sidebands. As  increases the numb
sidebands increases. This is referred to as wideband FM (WBFM).

26
 VHF/FM
VHF/FM (Very High Frequency band = 30MHz – 300MHz) radio transmissions, in
band 88MHz to 108MHz have the following parameters:
Max frequency input (e.g. music) fm
15kHz
Deviation 75kHz f c  Vm
f c
Modulation Index  5 
fm
For  = 5 there are 16 sidebands and the FM signal bandwidth is 16fm = 16 x 15
= 240kHz.Applying Carson’s Rule BW = 2(75+15) = 180kHz.

27
 Comments FM

• The FM spectrum contains a carrier component and an infinite number of sideba

at frequencies fc  nfm (n = 0, 1, 2, …)

FM signal,v s (t )  Vc J
n  
n (  ) cos( c  n m )t

• In FM we refer to sideband pairs not upper and lower sidebands. Carrier or othe
components may not be suppressed in FM.

• The relative amplitudes of components in FM depend on the values Jn(),

where
Vm
 thus the component at the carrier frequency depends on m(t), as do all
fm
other components and none may be suppressed.
28
 Comments FM

• Components are significant if Jn()  0.01. For <<1 (  0.3 or less) only J
J1() are significant, i.e. only a carrier and 2 sidebands. Bandwidth is 2fm, simila
DSBAM in terms of bandwidth - called NBFM.

f c

• Large modulation index means that a large bandwidth is required – called
fm
WBFM.

• The FM process is non-linear. The principle of superposition does not apply. Whe
m(t) is a band of signals, e.g. speech or music the analysis is very difficult
(impossible?). Calculations usually assume a single tone frequency equal to the
maximum input frequency. E.g. m(t)  band 20Hz  15kHz, fm = 15kHz is used

29
 Power in FM Signals.

v s (t )  Vc
From the equation for FM J
n  
n (  ) cos( c  n m )t

we see that the peak value of the components is VcJn() for the nth component.
2
 V pk 
 =   (V RMS ) 2 then the nth component is
Single normalised average power
 2
2
 Vc J n (  )  V J (  )) 2

   c n
 2  2

Hence, the total power in the infinite spectrum is

(Vc J n (  )) 2

Total power PT  
n   2
30
 Power in FM Signals.
By this method we would need to carry out an infinite number of calculations to f
PT. But, considering the waveform, the peak value is V­c, which is constant.
2
 V pk  V
 is  c
Since we know that the RMS value of a sine wave
 2 2

2 2
 V c  Vc
2 
Vc J n (  ) )
2 P 
and power = (VRMS) then we may deduce that
T 
 2
   
2 n   2
Hence, if we know Vc for the FM signal, we can find the total power PT for the infin
spectrum with a simple calculation. 31
 Power in FM Signals.
Now consider – if we generate an FM signal, it will contain an infinite number of
sidebands. However, if we wish to transfer this signal, e.g. over a radio or cable, t
implies that we require an infinite bandwidth channel. Even if there was an infinit
channel bandwidth it would not all be allocated to one user. Only a limited bandw
is available for any particular signal. Thus we have to make the signal spectrum f
the available channel bandwidth. We can think of the signal spectrum as a ‘train’
the channel bandwidth as a tunnel – obviously we make the train slightly less wid
than the tunnel if we can.

32
 Power in FM Signals.

However, many signals (e.g. FM, square waves, digital signals) contain an infinite
number of components. If we transfer such a signal via a limited channel bandwi
we will lose some of the components and the output signal will be distorted. If w
an infinitely wide train through a tunnel, the train would come out distorted, the
question is how much distortion can be tolerated?
Generally speaking, spectral components decrease in amplitude as we move awa
from the spectrum ‘centre’.

33
 Power in FM Signals.

In general distortion may be defined as

Power in total spectrum - Power in Bandlimited spectrum

D
Power in total spectrum

PT  PBL
D
PT
With reference to FM the minimum channel bandwidth required would be just wid
enough to pass the spectrum of significant components. For a bandlimited FM
spectrum, let a = the number of sideband pairs, e.g. for  = 5, a = 8 pairs
(16 components). Hence, power in the bandlimited spectrum PBL is
a
(Vc J n (  )) 2
PBL   = carrier power + sideband powers.
n  a 2
34
 Power in FM Signals.
Vc2
Since PT 
2
Vc2 Vc2 a
  ( J n (  )) 2 a
2 2 n a 2
Distortion D 
Vc2
 1  
n a
( J n (  ))
2

Also, it is easily seen that the ratio

a
Power in Bandlimited spectrum PBL
D    ( J n (  )) 2 = 1 – Distortion
Power in total spectrum PT n a

a
2
( J n ( =))
i.e. proportion pf power in bandlimited spectrum to total power 
n a
35
 Example

Consider NBFM, with  = 0.2. Let Vc = 10 volts. The total power in the infinite

Vc2 a
2
spectrum = 50 Watts, i.e. ( J n (  )) = 50 Watts.
2 n  a

From the table – the significant components are

n Jn(0.2) Amp = VcJn(0.2) ( Amp ) 2

Power =
2
0 0.9900 9.90 49.005
1 0.0995 0.995 0.4950125
PBL = 49.5 Watts

49.5
i.e. the carrier + 2 sidebands contain  0.99 or 99% of the total power
50
36
 Example

PT  PBL 50  49.5
Distortion =   0.01 or 1%.
PT 50
Actually, we don’t need to know Vc, i.e. alternatively
1
2
1
Distortion =  (J
n  1
n ( 0. 2)) (a = 1)

2 2
D = 1  (0.99)  (0.0995)  0.01

1
PBL
Ratio   ( J n (  )) 2  1  D  0.99
PT n  1

37
 FM Demodulation –General Principles.

• An FM demodulator or frequency discriminator is essentially a frequency-to-

converter (F/V). An F/V converter may be realised in several ways, including for
example, tuned circuits and envelope detectors, phase locked loops etc.
Demodulators are also called FM discriminators.

• Before considering some specific types, the general concepts for FM demodulati
will be presented. An F/V converter produces an output voltage, VOUT which is
proportional to the frequency input, fIN.

38
 FM Demodulation –General Principles.

• If the input is FM, the output is m(t), the analogue message signal. If the input i
the output is d(t), the digital data sequence.

• In this case fIN is the independent variable and VOUT is the dependent variable (
y axes respectively). The ideal characteristic is shown below.

We define Vo as the output when fIN = fc, the nominal input frequency. 39
 FM Demodulation –General Principles.

V
The gradient is called the voltage conversion factor
f
i.e. Gradient = Voltage Conversion Factor, K volts per Hz.

Considering y = mx + c etc. then we may say VOUT = V0 + KfIN from the frequenc
modulator, and since V0 = VOUT when fIN = fc then we may write

VOUT  V0  KV IN

where V0 represents a DC offset in VOUT. This DC offset may be removed by level

shifting or AC coupling, or the F/V may be designed with the characteristic shown

40
 FM Demodulation –General Principles.

The important point is that VOUT = KVIN. If VIN = m(t) then the output contains t
message signal m(t), and the FM signal has been demodulated.

41
 FM Demodulation –General Principles.

1

Often, but not always, a system designed soKthat , so that K = 1 and

VOUT = m(t).
A complete system is illustrated.

42
FM Demodulation –General Principles.

43
 Methods
Tuned Circuit – One method (used in the early days of FM) is to use the slope o
tuned circuit in conjunction with an envelope detector.

44
 Methods

• The tuned circuit is tuned so the fc, the nominal input frequency, is on the slope,
the centre of the tuned circuits. As the FM signal deviates about fc on the tuned
slope, the amplitude of the output varies in proportion to the deviation from
the FM signal is effectively converted to AM. This is then envelope detected by th
diode etc to recover the message signal.

• Note: In the early days, most radio links were AM (DSBAM). When FM came alon
with its advantages, the links could not be changed to FM quickly. Hence, NBFM w
used (with a spectral bandwidth = 2fm, i.e. the same as DSBAM). The carrier
frequency fc was chosen and the IF filters were tuned so that fc fell on the slope
filter response. Most FM links now are wideband with much better demodulators.

• A better method is to use 2 similar circuits, known as a Foster-Seeley Discrim

45
 Foster-Seeley Discriminator

This gives the composite characteristics shown. Diode D2 effectively inverts the
tuned circuit response. This gives the characteristic ‘S’ type detector.

46
 Phase Locked Loops PLL

• A PLL is a closed loop system which may be used for FM demodulation. A full
analytical description is outside the scope of these notes. A brief description is
presented. A block diagram for a PLL is shown below.

• Note the similarity with a synchronous demodulator. The loop comprises a multip
a low pass filter and VCO (V/F converter as used in a frequency modulator).
47
 Phase Locked Loops PLL

• The input fIN is applied to the multiplier and multiplied with the VCO frequency output fO, to
produce  = (fIN + fO) and  = (fIN – fO).

• The low pass filter passes only (fIN – fO) to give VOUT which is proportional to (fIN – fO).

• If fIN  fO but not equal, VOUT = VIN, fIN – fO is a low frequency (beat frequency) signal to the
VCO.

• This signal, VIN, causes the VCO output frequency fO to vary and move towards fIN.

• When fIN = fO, VIN (fIN – fO) is approximately constant (DC) and fO is held constant, i.e locked to
fIN.

• As fIN changes, due to deviation in FM, fO tracks or follows fIN. VOUT = VIN changes to drive fO to
track fIN.

• VOUT is therefore proportional to the deviation and contains the message signal m(t).

48
 UNIT-III

RADIO RECEIVERS
Tuned Radio Frequency (TRF) Receivers
 Composed of RF amplifiers and detectors.
 No frequency conversion. It is not often used.
 Difficult to design tunable RF stages.
 Difficult to obtain high gain RF amplifiers

Active Detector Bandpass Baseband

Tuning Circuit Filter Audio Amp
Circuit

Local
Oscillator
 Heterodyning

All Fixed
Incoming Intermediate
Frequencies Frequency
Heterodyning Subsequent
(Upconversion/ Processing
Downconversion) (common)
Superheterodyne Receivers

Superheterodyne Receiver Diagram

Superheterodyne Receiver
 Superheterodyne Receivers
 The RF and IF frequency responses H1(f) and H2(f) are
important in providing the required reception characteristics.
Superheterodyne Receivers

RF
Response

fI fI
F F

IF
Response
Superheterodyne Receivers
Superheterodyne Receiver Frequencies
Superheterodyne Receiver Frequencies
Frequency Conversion Process
Image Frequencies

Image frequency is also

received

Image frequency not a problem.

AM Radio Receiver
Superheterodyne Receiver Typical Signal Levels
Double-conversion block diagram.
Noise in Communication
Systems

115
 Noise in Communication Systems

1. Introduction 11. Signal - to – Noise

2. Thermal Noise 12. Noise Factor – Noise Figure
3. Shot Noise 13. Noise Figure / Factor for Active
4. Low Frequency or Flicker Noise Elements
5. Excess Resister Noise 14. Noise Temperature
6. Burst or Popcorn Noise 15. Noise Figure / Factors for Passive
7. General Comments Elements
8. Noise Evaluation – Overview 16. Review – Noise Factor / Figure /
9. Analysis of Noise in Communication Temperature
Systems 17. Cascaded Networks
• Thermal Noise 18. System Noise Figure
• Noise Voltage Spectral Density 19. System Noise Temperature
• Resistors in Series 20. Algebraic Representation of Noise
• Resistors in Parallel 21. Additive White Gaussian Noise
10.Matched Communication Systems

116
 1.. Introduction
Noise is a general term which is used to describe an unwanted signal
which affects a wanted signal. These unwanted signals arise from a
variety of sources which may be considered in one of two main
categories:-

•Interference, usually from a human source (man made)

•Naturally occurring random noise

Interference

Interference arises for example, from other communication systems

(cross talk), 50 Hz supplies (hum) and harmonics, switched mode
power supplies, thyristor circuits, ignition (car spark plugs) motors
… etc.
117
 1.. Introduction (Cont’d)
Natural Noise

Naturally occurring external noise sources include atmosphere disturbance

(e.g. electric storms, lighting, ionospheric effect etc), so called ‘Sky Noise’
or Cosmic noise which includes noise from galaxy, solar noise and ‘hot
spot’ due to oxygen and water vapour resonance in the earth’s atmosphere.

118
 2. Thermal Noise (Johnson Noise)
This type of noise is generated by all resistances (e.g. a resistor,
semiconductor, the resistance of a resonant circuit, i.e. the real part of the
impedance, cable etc).

Experimental results (by Johnson) and theoretical studies (by Nyquist) give
the mean square noise voltage as _ 2
V  4 k TBR (volt 2 )
Where k = Boltzmann’s constant = 1.38 x 10-23 Joules per K
T = absolute temperature
B = bandwidth noise measured in (Hz)
R = resistance (ohms) 119
 2. Thermal Noise (Johnson Noise) (Cont’d)
The law relating noise power, N, to the temperature and bandwidth is

N = k TB watts

Thermal noise is often referred to as ‘white noise’ because it has a

uniform ‘spectral density’.

120
 3. Shot Noise
• Shot noise was originally used to describe noise due to random
fluctuations in electron emission from cathodes in vacuum tubes
(called shot noise by analogy with lead shot).
• Shot noise also occurs in semiconductors due to the liberation of
charge carriers.
• For pn junctions the mean square shot noise current is
I n2  2I DC  2 I o ) qe B (amps) 2
Where
is the direct current as the pn junction (amps)
is the reverse saturation current (amps)
is the electron charge = 1.6 x 10-19 coulombs
B is the effective noise bandwidth (Hz)

• Shot noise is found to have a uniform spectral density as for thermal

noise 121
 4. Low Frequency or Flicker Noise

Active devices, integrated circuit, diodes, transistors etc also exhibits

a low frequency noise, which is frequency dependent (i.e. non
uniform) known as flicker noise or ‘one – over – f’ noise.

5. Excess Resistor Noise

Thermal noise in resistors does not vary with frequency, as previously
noted, by many resistors also generates as additional frequency
dependent noise referred to as excess noise.
6. Burst Noise or Popcorn Noise
Some semiconductors also produce burst or popcorn noise with a
2

spectral density which is proportional to  1 f 

122
 7. General Comments

For frequencies below a few KHz (low frequency systems), flicker

and popcorn noise are the most significant, but these may be ignored
at higher frequencies where ‘white’ noise predominates.

123
 8. Noise Evaluation
The essence of calculations and measurements is to determine the
signal power to Noise power ratio, i.e. the (S/N) ratio or (S/N)
expression in dB.  S  S
  
 N  ratio N
 S   S 
   10 log 10  
 N  dB  N 
Also recall that
 S ( mW ) 
S dBm  10 log 10  
 1 mW 
 N ( mW ) 
and N dBm  10 log 10  
 1 mW 
 S 
i .e .   10 log 10 S  10 log 10 N
 N  dB
 S 
   S dBm  N dBm
 N  dB
124
 8. Noise Evaluation (Cont’d)

The probability of amplitude of noise at any frequency or in any band

of frequencies (e.g. 1 Hz, 10Hz… 100 KHz .etc) is a Gaussian
distribution.

125
 8. Noise Evaluation (Cont’d)
Noise may be quantified in terms of
noise power spectral density, po watts per
Hz, from which Noise power N may be
expressed as
N= po Bn watts
Ideal low pass filter
Bandwidth B Hz = Bn
N= po Bn watts
Practical LPF
3 dB bandwidth shown, but noise does not suddenly cease
at B3dB
Therefore, Bn > B3dB, Bn depends on actual filter.
N= p0 Bn
In general the equivalent noise bandwidth is > B3dB.
126
 9. Analysis of Noise In Communication Systems

Thermal Noise (Johnson noise)

This thermal noise may be represented by an equivalent circuit as shown below
____
V  4 k TBR (volt 2 )
2

(mean square value , power)

then VRMS = V____2  2 kTBR  Vn
i.e. Vn is the RMS noise voltage.

A) System BW = B Hz
N= Constant B (watts) = KB
B) System BW
N= Constant 2B (watts) = K2B

For A, S  S For B, S  S
N KB N K 2B

127
 9. Analysis of Noise In Communication Systems (Cont’d)

Resistors in Series
Assume that R1 at
temperature T1 and R2 at
temperature T2, then
____ ___ ___
2 2 2
V V
n n1 V n2
____
2
V n1
____
 4 k T1 B R1
2
Vn 2  4 k T2 B R2
____
2
 V n  4 k B (T1 R1  T2 R2 )
____
2
V n  4 kT B ( R1  R2 )
i.e. The resistor in series at same temperature behave as a
single resistor 128
 9. Analysis of Noise In Communication Systems (Cont’d)

Resistance in Parallel
R2 R1
Vo1  Vn1 Vo2 Vn2
R1  R2 R1  R2

____ ___ ___

2 2 2
V V
n o1 V o2

____
4 kB R R 
V  R  R )2 R 2 T1 R1  R1 T 2 R 2   R R 
2 2 2 1 2
n
1 2  1 2

_____
2 4 kB R1 R 2 (T1 R1  T2 R 2 )
V n 
R1  R 2 )2
_____
2  RR 
V n  4kTB  1 2 
 R1  R2 

129
 10. Matched Communication Systems
In communication systems we are usually concerned
with the noise (i.e. S/N) at the receiver end of the system.
The transmission path may be for example:-

Or

An equivalent circuit, when the line is connected to the receiver is shown below.

130
10. Matched Communication Systems (Cont’d)

131
 11. Signal to Noise
The signal to noise ratio is given by
S Signal Power

N Noise Power
The signal to noise in dB is expressed by
S S
  dB 10 log 10  
N N
 S 
  dB  S dBm  N dBm for S and N measured in mW.
N 

12. Noise Factor- Noise Figure

Consider the network shown below,

132
 12. Noise Factor- Noise Figure (Cont’d)
• The amount of noise added by the network is embodied in the
Noise Factor F, which is defined by
S N )
IN
Noise factor F =
S N )
OUT

• F equals to 1 for noiseless network and in general F > 1. The

noise figure in the noise factor quoted in dB
i.e. Noise Figure F dB = 10 log10 F F ≥ 0 dB

• The noise figure / factor is the measure of how much a network

degrades the (S/N)IN, the lower the value of F, the better the
network.
133
 13. Noise Figure – Noise Factor for Active Elements
For active elements with power gain G>1, we have

S N )
F= IN
= S IN N OUT But SOUT  G S IN
S N )
OUT
N IN S OUT
Therefore
S IN N OUT N
F  OUT
N IN G S IN G N IN
Since in general F v> 1 , then NOUT is increased by noise due to the active element i.e.

Na represents ‘added’ noise measured at the output. This added noise may be referred to the
input as extra noise, i.e. as equivalent diagram is

134
13. Noise Figure – Noise Factor for Active Elements (Cont’d)

Ne is extra noise due to active elements referred to the input; the element is thus
effectively noiseless.

135
14. Noise Temperature

136
15. Noise Figure – Noise Factor for Passive Elements

137
16. Review of Noise Factor – Noise Figure –Temperature

138
 17. Cascaded Network
A receiver systems usually consists of a number of passive or active elements connected in
series. A typical receiver block diagram is shown below, with example

In order to determine the (S/N) at the input, the overall receiver noise figure or noise
temperature must be determined. In order to do this all the noise must be referred to the same
point in the receiver, for example to A, the feeder input or B, the input to the first amplifier.

Te or N e is the noise referred to the input.

139
 18. System Noise Figure
Assume that a system comprises the elements shown below,

Assume that these are now cascaded and connected to an aerial at the input, with N IN  N ae
from the aerial.

Now , N OUT  G3 N IN 3  N e3 )
 G3 N IN3  F3  1) N IN )
Since N IN 3  G2 N IN 2  N e 2 )  G2 N IN 2  F2  1)N IN )

similarly N IN 2  G 1  N ae   F1  1 )N IN )
140
 18. System Noise Figure (Cont’d)
N OUT  G3 G2 G1 N ae  G1 F1  1)N IN   G2 F2  1)N IN   G3 F3  1)N IN
The overall system Noise Factor is

N OUT N OUT
Fsys  
GN IN G1G2 G3 N ae
N IN F2  1) N IN F3  1) N IN
 1  F1  1)  
N ae G1 N ae G1G2 N ae

 F2 1) F3 1) F4 1) Fn 1)

Fsys F 
1    ........... 
G1 G1G2 G1G2G3 G1G2 ..........Gn1
The equation is called FRIIS Formula.
141
19. System Noise Temperature

142
 20. Algebraic Representation of Noise
Phasor Representation of Signal and Noise
The general carrier signal VcCosWct may be represented as a phasor at any instant
in time as shown below:

If we now consider a carrier with a noise voltage with “peak” value superimposed we
may represents this as:

Both Vn and  n are random variables, the above phasor diagram represents a snapshot
at some instant in time.

143
Chapter 5. Noise in CW
Modulation System

144
Noise in CW ModulationSystem
•5.1 Introduction
• - Receiver Noise (Channel Noise) :
• additive, White, and Gaussian 으로 가정

•5.2 Receiver Model

• 1. RX Model
•

N
- w(t): additive, white, and Gaussian, power spectraldensity  0
2
Sw(f)

N 0
2
f
Rw()
N0
 ( )
2


•N0 = KTe where K = Boltzmann’s constant
•Te = equivalent noise Temp.
•Average noise power per unit bandwidth

145
• - Band Pass Filter (Ideal SNI, SNQ
case) N0

2B

2B

BPF
• w(t) n(t)
•
• - filtered noise as narrow-band
• noise
n(t) = nI(t)cos(2pfCt) - nQ(t)sin(2pfCt)
• where nI(t) is inphase, nQ(t) is quadrature
component

• -  filtered signal x(t)

• x(t) = s(t) + n(t)
•
• - Average Noise Power = N0BT
average power of the modulated signal s(t)
- (SNR)I 
• average power of the filtered noise n(t)
average power of the demodulate d message signal
- (SNR) O 
average power of the noise receiver
output

146
- DSB
SY(f)
1
SM(f) SS(f)
1
1 2
4 
f f f
m(t)  P P P
m(t)cos(2π f t)
C  2 ( ) 
4 2
1
- s(t)  m(t)cos(2π fCt Θ)  S (f) S S (f  fM )  SC (f  f )M C
4
SS(f)
N0 N0
2 2

f f
N0 N0
2W  WN 0 4W 2WN 0
2 2
1 m(t)  1 n (t)
- SSB 2 2 I

1
1
4
f f
1 1  
m(t)cos(2π fC t)  m ˆ C
2 1 P2 P P 4 2 2 4
(t)sin(2π f t)     
N0 N0
2 2

f f
N0 N0
2W  W N0 2W  W N0
2 2
1 m(t)  1 n (t)cos(π Wt)  1 n (t) sin(π Wt)
I Q
4 2 2

147
 • - s(t) by each system has the same average power
• - noise w(t) has the same average power measured in the
message
• BW =W
• 1) ChannelSNR

average power of the modulated signal

(SNR) C 
average power of the noise in the message BW at receiver
input
(SNR)
Figure of merit =
O (SNR)
• 2) C

•Noise in DSB-SC
Receivers
1. Model of DSB-SC Receivers
•

148
 - s(t)  CAC cos(2π fCt)m(t)
whe re C : scaling factor Power spectral
density of m(t) : SM (f) W : message
bandwidth

- Average signal power

P ∫ -W
W S (f) df
M
C2 A2 P
- Average power of s(t)  C
2
N
- Average noise power  2W  0  WN 0
2
(baseband)

C 2AC2P
- (SNR ) C,DS 
B
2WN0

- x(t)  s(t)  n(t)

 CAC cos(2π fCt)m(t)  nI(t)cos(2π fCt)  nQ (t) sin(2π
fCt)
- v(t)  x(t)cos(2π fCt)
• 2. (SNR)1
O
 CACm(t)
2
1
2
n(t)
I
1
2
CACm(t)  n(t)
t)
1
I cos(4πCf t)  ACnQ (t) sin(4πCf
2

1 1
∴ y(t)  CAC m(t)  I
n (t) 2 2

149
 C2 A 2 P
- Average signal power  C
4
1 1
- Average noise power  (2W)N 0  WN 0 (passband)
4 2
Power(n I(t))  Power of bandpass filterednoise n(t)  2WN0
C 2 A C2 P 4 C 2A C2P
- ∴ (SNR O  
) WN0 2 2W N0
∴ Figureof merit
(SNR)O
1
(SNR )C DSBSC

1 1
• Noise in SSB Rece ivers
s(t) 
2
CA C cos(2π fC t)m(t)  CAC sin(2π fCt)mˆ
2
(t)
• - SSB Modulated wave
 m (t) and m̂(t) are othogonal, E[m (t)]  0
⇒ m(t) and mˆ(t) are uncorrelat ed
⇒ their power spectral densities are additive
 m(t) and mˆ(t) has the same power spectral density

C2 A 2C P C2 A 2C P C2 A 2CP
- Message power   
4 2 4 2 4
(half of DSB)
- Average noise power  WN0 ( message BW 안의 Noise)
(baseband) 2 2
C A CP
(SNR) C,SS 
B
4WN0
150
  W   W 
n(t)  nI(t)cos 2π(fC  )t - nQ(t) sin 2π(fC  )t
 2   2 

151
 - Combinedoutput
1 1 1
y(t)  CACm(t)  n I(t) cos(π Wt)  nQ(t) sin(π Wt)
4 2 2
1
- Average signal power  C2 A 2CP
16
1 WN0 1 WN0 1
- Average noise power    WN 0 (passband)
4 2 4 2 4
C 2AC2P
- (SNR) O,SS 
B
4WN0

(SNR)O
- Figure of merit 1 same as DSB - SC
(SNR)C SSB

- AM signal
s(t)  AC [1 kam(t)]cos(2π fCt)

•5.4 Noise in AM Receiver

- Average signal power  A 2C(1 k2aP) 2
•
- Average noise power  WN0 ← (2W 
N0
2
)

A2 (1 k2P)
(SNR)C,AM  C
2WaN0

- Filtered signal x(t)  s(t)  n(t)

 [AC  ACkam(t)  nI(t)]cos(2π fCt) - nQ (t)sin(2π fCt)

152
 y(t)  envelop of x(t)
1
 
 [A C  A Ck am(t)  nI (t)] 2  n2Q(t) 2
Assume AC [1 kam(t)]  nI(t),nQ (t)
y(t)  AC  ACkam(t)  nI(t)
A 2Ck a2P
- (SNR) O,A 
M
2W N0
Avg carrier power  Avg noise
조건 
power
 ka ≤ 1

(SNR )O k 2aP
- Figure of merit  1
(SNR )C AM 1 k2aP

• ex1)
m(t)  Single
A cos(2π-Tone
m f t) → P
m 
A
Modulation
2
2
m

s(t)  AC[1μ cos(2π fmt)]cos(2π fCt) where μ  ka Am

1 k2 A2
(SNR) O μ
 2 a 2 m2  2
(SNR) C AM 1 1 k aA m 2 μ
2 2
1
if μ  1, F.O.M  (max)
3

153
Threshold Effect
•Carrier-to-noise < 1
•narrow-band noise n(t)
n(t)  r(t)cos[2π fC (t) ψ(t)]
whe re r(t) is envelope, ψ(t) is phase

x(t)  s(t)  n(t)

 AC [1 kam(t)]cos(2π fCt)  r(t)cos(2π fCt ψ(t))

y(t)  r(t)  AC [1 kam(t)]cos[ψ(t)]

 r(t)  ACcos[ψ(t)]  ACkam(t)cos[ψ(t)] where ψ(t) is uniformly
distribute d over [0,2π ]

⇒ complete loss of informatio n

•Threshold Effect : loss of message in an envelope detector

that
• operates at a lowCNR.
•
154
• Noise in FM Receivers

• w(t) : zero mean white Gaussian noise with psd = No/2

• s(t) : carrier =fc, BW = BT 즉 (fC  BT/2)

• - BPF : [fC - BT/2 ~ fC + BT/2]

• - Amplitude limiter : remove amplitude
• variations by clipping and
•- BPF
 slope network or differentiator : varies linearly with
Discriminator
frequency
• - Baseband LPF
envelope detector
s(t)  AC cos[2π fCt  2π kf∫ t m(t)dt]
: 0
φ(t)  2π kf∫ 0 m(t)dt
t

s(t)  AC cos[2π fCt φ(t)]

• - FM signal
n(t)  nI(t)cos(2π fCt)  nQ (t) sin(2π fCt)
 r(t)cos[2π fCt ψ(t)]
r(t)  (n (t))2  (n (t))2
• - Filtered noise 
where 
I Q

1 nQ (t)
n(t) ψ(t)  tan  
  n I(t) 

155
 ∴ x(t)  s(t)  n(t)
 AC cos[2π fCt φ(t)]  r(t) cos[2π fCt ψ(t)]

 r(t) sin[ψ(t) φ(t)] 

where θ(t)  φ(t)  tan-1 
AC  r(t)cos[ψ(t) φ(t)]
Assume AC  r(t)
r(t)
θ(t)  φ(t)  sin[ψ(t) φ(t)]
AC
r(t)
 2π kf ∫ 0t m(t)dt  sin[ψ(t) φ(t)]
AC

1 dθ(t)
v(t)   k fm(t)  n d(t)
2π dt

where
1 d
n d (t)  {r(t) sin[ψ(t) φ(t)]}
2πA C dt
1 d
 {r(t) sin[ψ(t)]}
2πA C dt
at discriminator
output
1 dnQ (t)
 n d(t) 
2πA C dt

at Rx
output
156
• Pre-emphasis and de-emphasis in FM

• P.S.D. of noise at FM Rx output

• P.S.D. of typical message signal

signa
l

noise
1
H de (f ) , -WfW
Hpe (f )
P.S.D of noise nd (t) at the discriminator output
N0f 2
 f  BT
SNd (f)   A 2C 2
 0 otherwise


157