Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
101 views

Beam Element: Beams and Shafts Module-3

1) A beam element is modeled as a line segment representing the neutral axis of the beam with two degrees of freedom (DOF) at each node: transverse deflection and slope. 2) Hermite shape functions are used to describe the variation of deflection and slope along the element. 3) The stiffness matrix of the beam element is derived using the strain energy approach and integrating the shape functions. 4) A 3-node, 2-element beam model is analyzed under a uniform distributed load, and the deflection at the middle of the loaded element is calculated.

Uploaded by

Manda Ramesh Babu
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
101 views

Beam Element: Beams and Shafts Module-3

1) A beam element is modeled as a line segment representing the neutral axis of the beam with two degrees of freedom (DOF) at each node: transverse deflection and slope. 2) Hermite shape functions are used to describe the variation of deflection and slope along the element. 3) The stiffness matrix of the beam element is derived using the strain energy approach and integrating the shape functions. 4) A 3-node, 2-element beam model is analyzed under a uniform distributed load, and the deflection at the middle of the loaded element is calculated.

Uploaded by

Manda Ramesh Babu
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 14

BEAMS and SHAFTS

Module-3

Beam element
Beam is a structural member which is acted upon by a system of
external loads perpendicular to axis which causes bending that is
deformation of bar produced by perpendicular load as well as force
couples acting in a plane. Beams are the most common type of
structural component, particularly in Civil and Mechanical
Engineering. A beam is a bar-like structural member whose primary
function is to support transverse loading and carry it to the supports

A truss and a bar undergoes only axial deformation and it is


assumed that the entire cross section undergoes the same displacement,
but beam on other hand undergoes transverse deflection denoted by v.
Fig shows a beam subjected to system of forces and the deformation of
the neutral axis
We assume that cross section is doubly symmetric and bending take
place in a plane of symmetry. From the strength of materials we
observe the distribution of stress as shown.

Where M is bending moment and I is the moment of inertia.


According to the Euler Bernoulli theory. The entire c/s has the same
transverse deflection V as the neutral axis, sections originally
perpendicular to neutral axis remain plane even after bending

Deflections are small & we assume that rotation of each section


is the same as the slope of the deflection curve at that point (dv/dx).
Now we can call beam element as simple line segment representing the
neutral axis of the beam. To ensure the continuity of deformation at any
point, we have to ensure that V & dv/dx are continuous by taking 2 dof
@ each node V & (dv/dx). If no slope dof then we have only
transverse dof. A prescribed value of moment load can readily taken
into account with the rotational dof  .

Potential energy approach


Strain energy in an element for a length dx is given by
But we know  = M y / I substituting this in above equation we get.

But

Therefore strain energy for an element is given by

Now the potential energy for a beam element can be written as


Hermite shape functions:
1D linear beam element has two end nodes and at each node 2
dof which are denoted as Q2i-1 and Q2i at node i. Here Q2i-1 represents
transverse deflection where as Q2i is slope or rotation. Consider a beam
element has node 1 and 2 having dof as shown.

The shape functions of beam element are called as Hermite shape


functions as they contain both nodal value and nodal slope which is
satisfied by taking polynomial of cubic order

that must satisfy the following conditions

Applying these conditions determine values of constants as


Solving above 4 equations we have the values of constants

Therefore

Similarly we can derive

Following graph shows the variations of Hermite shape functions


Stiffness matrix:
Once the shape functions are derived we can write the equation
of the form

But

ie

Strain energy in the beam element we have


Therefore total strain energy in a beam is

Now taking the K component and integrating for limits -1 to +1 we get


Beam element forces with its equivalent loads
Uniformly distributed load

Point load on the element

Varying load

Bending moment and shear force


We know

Using these relations we have


Solution:
Let’s model the given system as 2 elements 3 nodes finite
element model each node having 2 dof. For each element determine
stiffness matrix.

Global stiffness matrix


Load vector because of UDL
Element 1 do not contain any UDL hence all the force term for
element 1 will be zero.
ie

For element 2 that has UDL its equivalent load and moment are
represented as

ie

Global load vector:


From KQ=F we write

At node 1 since its fixed both q1=q2=0


node 2 because of roller q3=0
node 3 again roller ie q5= 0
By elimination method the matrix reduces to 2 X 2 solving this we
have Q4= -2.679 X 10-4mm and Q6 = 4.464 X10-4mm

To determine the deflection at the middle of element 2 we can write the


displacement function as

= -0.089mm
Solution: Let’s model the given system as 3 elements 4 nodes finite
element model each node having 2 dof. For each element determine
stiffness matrix. Q1, Q2……Q8 be nodal displacements for the entire
system and F1……F8 be nodal forces.

Global stiffness matrix:


Load vector because of UDL:
For element 1 that is subjected to UDL we have load vector as

ie

Element 2 and 3 does not contain UDL hence

Global load vector:


And also we have external point load applied at node 3, it gets added to
F5 term with negative sign since it is acting downwards. Now F
becomes,

From KQ=F

At node 1 because of roller support


q1=0 Node 4 since fixed q7=q8=0
After applying elimination and solving the matrix we determine the
values of q2, q3, q4, q5 and q6.

You might also like