WWW - Manaresults.Co - In: (Common To CE, CEE)

Code No: 124AA R15
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD

B.Tech II Year II Semester Examinations, May - 2017
HYDRAULICS AND HYDRAULIC MACHINERY
(Common to CE, CEE)
Time: 3 Hours Max. Marks: 75
Note: This question paper contains two parts A and B.

Part A is compulsory which carries 25 marks. Answer all questions in Part A.
Part B consists of 5 Units. Answer any one full question from each unit.
Each question carries 10 marks and may have a, b, c as sub questions.
PART- A (25 Marks)

1.a) Differentiate between subcritical flow and supercritical flow. [2]
b) What is hydraulic jump? [3]
c) State Rayleigh’s method of dimension analysis. [2]
d) What are geometric, kinematic and dynamic similarities? [3]
e) State the principle of Angular momentum. [2]
f) Explain Hydraulic efficiency, mechanical efficiency and overall efficiency. [3]
g) Explain about surge tank in turbines. [2]
h) Define specific speed of turbine. [3]
i) Differentiate between single stage and multi stage pump. [2]
j) Define utilization factor and capacity factor. [3]
PART-B (50 Marks)

2.a) Derive expression for kinetic energy correction factor.
b) Velocity distribution in an open rectangular channel is given by V=3y½. If the
width of the channel is 10 m and the depth of flow is 1m, find the average
velocity of the cross section, energy correction factor and momentum correction
factor. [5+5]
OR
3.a) Define hydraulic jump. Explain various types of hydraulic jump. Derive the head
loss in hydraulic jump.
b) A gate is to be suddenly dropped into a place closing a rectangular channel 2 m
deep and 3 m wide in which 6 cumec of water is flowing at a depth of 1.2 m. Will
the water spill over the sides? What will be the velocity and height of surge
produced? [5+5]
4.a) Explain about different types of forces acting in moving fluid.

b) The pressure difference ∆p in a pipe of diameter D and length due to turbulent
flow depends on the velocity V, viscosity µ, density ρ and roughness k. Using
Buckingham’s π-theorem, obtain expression for ∆p. [5+5]
OR
5.a) What are different types of dimensionless numbers and explain them?
b) A ship model of scale 1/50 is towed through sea water at a speed of 1 m/s. A force
of 2 N is required to tow the model. Determine the speed of ship and propulsive
force on the ship, if the prototype is subjected to wave resistance only. [5+5]
WWW.MANARESULTS.CO.IN
6.a) Show that the force exerted by a jet of water on an inclined fixed plate in the
direction of the jet is given by Fx=ρ aV2 Sin2 θ, where a = Area of the jet,
V = velocity of the jet and θ = inclination of the plate with the jet.
b) A jet of water having a velocity of 20 m/sec strikes a curved vane which is
moving with a velocity of 9 m/sec. The vane is symmetrical and is so shaped that
the jet is deflected through 120 degrees. Find the angle of the jet at inlet of the
vane if there is no shock. What is the absolute velocity of the jet at outlet in
magnitude and direction and the work done per second per unit weight of water
strikings. Assume the vane to be smooth. [5+5]
OR
7.a) Prove that the force exerted by a jet of water on a fixed semi-circular plate in the
direction of the jet when the jet strikes at the centre of the semi-circular plate is
two times the force exerted by the jet on an fixed vertical plane.
b) A jet of water of 10 cm diameter is discharging under a constant head of 80 m.
Find the force exerted by the jet on a fixed plate. Take coefficient of velocity as
0.9. [5+5]
8.a) What are the uses of a draft tube? Describe with neat sketches different types of
draft tubes.
b) A turbine develops 7355 kW under a head of 24.7 m at 210 rpm. What is its
specific speed? Indicate the type of turbine suitable for this purpose. If this turbine
is tested in the laboratory where the head of water available is only 7.5 m, what
power will it develop at what speed? [5+5]
OR
9.a) Define the term unit power, unit speed and unit discharge with reference to a
hydraulic turbine. And also derive the expression for these terms.
b) A turbine develops 9000 kW when running at a speed of 140 rpm and under a
head of 30 m. Determine the specific speed of the turbine. [5+5]
10.a) Define cavitation. What are the effects of cavitation? Give the necessary
precaution against the cavitation.
b) The diameter of an impeller of a centrifugal pump at inlet and outlet are 300 mm
and 600 mm respectively. The velocity of flow at outlet is 2.5 m/sec and vanes are
set back at an angle of 45 degrees at outlet. Determine the minimum starting
speed of the pump if the manometer efficiency is 75%. [5+5]
OR
11.a) What are the various applications of Hydroelectric power plant.
b) A centrifugal pump rotating at 1000 rpm delivers 160 liters/s of water against a
head of 30 m. The pump is installed at a place where atmospheric pressure is
1×105 Pa(abs.) and vapour pressure of water is 2 kPa (abs.). The head loss in
suction pipe is equivalent to 0.2 m of water. Calculate minimum NPSH. [5+5]
---ooOoo---
WWW.MANARESULTS.CO.IN

WWW - Manaresults.Co - In: (Common To CE, CEE)

Uploaded by

Copyright:

Available Formats

WWW - Manaresults.Co - In: (Common To CE, CEE)

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

WWW - Manaresults.Co - In: (Common To CE, CEE)

Uploaded by

Copyright:

Available Formats

Code No: 124AA R15

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD

Note: This question paper contains two parts A and B.

PART- A (25 Marks)

PART-B (50 Marks)

4.a) Explain about different types of forces acting in moving fluid.

You might also like