Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
61 views

Design of Welded Connections: Submitted To Prof. Berlanty Iskander by

The document discusses types of welded joints including butt joints. It describes various types of butt joints and their edge preparations. The objectives are to study dimensions for butt joints according to standards. Required items include templates for joints.

Uploaded by

احمد حمدي
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
61 views

Design of Welded Connections: Submitted To Prof. Berlanty Iskander by

The document discusses types of welded joints including butt joints. It describes various types of butt joints and their edge preparations. The objectives are to study dimensions for butt joints according to standards. Required items include templates for joints.

Uploaded by

احمد حمدي
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 17

Akhbar Elyoum Academy, Mechanical Engineering Department

DESIGN OF WELDED
CONNECTIONS

submitted to prof. Berlanty Iskander

by

Ahmed Hamdy

24/2/2019
Objectives
Study stander dimensions for butt joint for ISO 4063 and American welding
society

Required
Stander for the joint
Introduction

Welding is a common process for joining metals using a large


variety of applications. Welding occurs in several locations, from
outdoors settings on rural farms and construction sites to inside
locations, such as factories and job shops. Welding processes are fairly
simple to understand, and basic techniques can be learned quickly.
Welding is the joining of metals at a molecular level. A weld is a
homogeneous bond between two or more pieces of metal, where the
strength of the welded joint exceeds the strength of the base pieces of
metal.
At the simplest level, welding involves the use of four components: the
metals, a heat source, filler metal, and some kind of shield from the air.
The metals are heated to their melting point while being shielded from
the air, and then a filler metal is added to the heated area to produce a
single piece of metal. It can be performed with or without filler metal
and with or without pressure.
Types of joints and welds

By means of welding, it is possible to make continuous, load bearing


joints between the members of a structure. A variety of joints is used in
structural steel work and they can be classified into four basic
configurations namely, Lap joint, Tee joint, Butt joint and Corner joint.
For lap joints, the ends of two members are overlapped and for butt
joints, the two members are placed end to end. The T- joints form a Tee
and in Corner joints, the ends are joined like the letter L. Most common
joints are made up of fillet weld or the butt (also calling groove) weld. Plug
and slot welds are not generally used in structural steel work. Fillet welds
are suitable for lap joints and Tee joints and groove welds for butt and
corner joints. Butt welds can be of complete penetration or incomplete
penetration depending upon whether the penetration is complete through
the thickness or partial. Generally a description of welded joints requires an
indication of the type of both the joint and the weld.
Butt welds

Full penetration butt welds are formed when the parts are connected
together within the thickness of the parent metal. For thin parts, it is
possible to achieve full penetration of the weld. For thicker parts, edge
preparation may have to be done to achieve the welding. There are nine
different types of butt joints: square, single V, double V, single U, double U,
single J, double J, single bevel and double bevel. conditions to be satisfied
while making the welds.
Welds are also classified according to their position into flat,
horizontal, vertical
and overhead. Flat welds are the most economical to make while overhead
welds are the most difficult and expensive

Fig 1
The main use of butt welds is to connect structural members, which
are in the same plane. A few of the many different butt welds are shown in
Fig.2. There are many variations of butt welds and each is classified
according to its particular shape.
Each type of butt weld requires a specific edge preparation and is named
accordingly.
The proper selection of a particular type depends upon: Size of the
plate to be joined; welding is by hand or automatic; type of welding
equipment, whether both sides are accessible and the position of the weld.
Butt welds have high strength, high resistance to impact and cyclic stress.
They are most direct joints and introduce least eccentricity in the joint.
Disadvantages of butt joint
high residual stresses, necessity of edge preparation and proper aligning of
the members in the field. Therefore, field butt joints are rarely used.

Fig. 2

Joint preparation
According to ISO 9692 Welding and allied processes -Recommendations
for joint preparation

a) (3) gas welding oxyfuel gas welding;


b) (5) beam welding:
c) (51) electron beam welding ;
d) (512) electron beam welding in atmosphere;
e) (52) laser welding, laser beam welding.

The number refer to the reference number of the welding process specified in ISO 4063.

Recommended table for butt joint


References
1. American welding society
2. ISO 4063
3. The National Programme on Technology Enhanced Learning
(NPTEL)
4. https://www.sciencedirect.com

You might also like