CATIA

Advanced Part Machining
Student Notes:
CATIA V5 Training
Foils
Advanced Part
Machining
Copyright DASSAULT SYSTEMES
Version 5 Release 19
January 2009
EDU_CAT_EN_AMG_FF_V5R19
Copyright DASSAULT SYSTEMES 1

About this course

Student Notes:
Objectives of the course

Upon completion of this course you will be able to:
- Identify and use the Advance Part Machining workbench tools
- Define a Multi-Axis Flank Contouring operation
- Define a Multi-Axis Helix Machining operation
- Define a Cavities Roughing operation
Targeted audience
Advanced NC Programmers
Prerequisites
Students attending this course should have knowledge of Numerical
Control Infrastructure (NCI), PMG, SMG and MMG workbench.
12 hours

Student Notes:
Table of Contents (1/2)
Introduction to Advanced Part Machining 6

About Advanced Part Machining 7
Operations in Advanced Machining Workbench 8
Multi-Axis Flank Contouring 9
About Multi-Axis Flank Contouring 10
General Process 11
Multi-Axis Flank Contouring: Geometry 12
Multi-Axis Flank Contouring: Strategy 21
To Sum Up 48
Multi-Axis Helix Machining 49
About Multi-Axis Helix Machining 50
General Process 51
Multi-Axis Helix Machining: Geometry 52
Multi-Axis Helix Machining: Strategy 58
To Sum Up 70
Cavities Roughing 71
Introduction 72
General Process 73

Student Notes:
Table of Contents (2/2)
Cavities Roughing: Geometry 74

Cavities Roughing: Strategy 92
To Sum Up 115

Student Notes:
How to Use This Course
To assist in the presentation and learning process, the course has been
structured as follows:
Lessons:
Lessons provide the key concepts, methodologies, and basic skill practice
exercises. The goal of each lesson is to present the necessary knowledge
and skills to master a basic level of understanding for a given topic.
Recap Exercises:
Recap Exercises are provided along at the end of each lesson to reinforce
the concepts learnt.
A Master Exercise:
A Master Exercise provides a project where an industry type part is used to
assist you in applying the key knowledge and skills acquired in the
individual lessons as they apply to real world scenarios.
Note: The Master Exercise is provided at the end of the

course to practice on key concepts in the lessons.

Student Notes:
Introduction to Advanced Part Machining

You will become familiar with the Advanced Part Machining.

Student Notes:
About Advanced Part Machining
Advanced Machining (AMG) workbench easily
generates high quality NC programs for machining
complex 3D parts and free form shapes. AMG is
beneficial to machine aerospace, turbo-machinery,
hydraulic and much more complex 3D parts, all in a
single machining solution.
AMG includes 2.5 to 5-axis machining technologies

and Axial machining. It brings new functionalities in
order to cover the entire machining process, in
addition to existing key functionalities in other
machining solutions.
AMG develops machining strategies that optimize

toolpaths, eliminate unnecessary air cutting, maximize
tool life, reduce programming time and increase overall
productivity.
AMG benefits the user for:

Quick tool path generation
Flexible management of tools and tool catalogs
Definition of Machining areas
Automated reworking
Fast tool path update after modification
Tool holder collision checking
Quick verification of tool path
Seamless NC data generation

Student Notes:
Operations in Advanced Machining Workbench
From drilling… …to complex 5 axis machining
(A) (C) (B)
This training is focused on (A) Multi-Axis Flank Contouring, (B) Multi-Axis Helix Machining
and (C) Cavities Roughing.
Refer to the PMG, SMG and MMG courses for learning the other operations of AMG workbench.

Student Notes:
Multi-Axis Flank Contouring

You will become familiar with the principles of 5-Axis Flank Machining.
About Multi-Axis Flank Contouring

General Process
Geometry
Strategy
To sum Up

Student Notes:
About Multi-Axis Flank Contouring
The Multi-Axis Flank Contouring operation is

mainly used for semi-finishing and finishing of 5
axis walls in structural parts. In this operation the
cutting tool machines with flank.
This is a profile contouring operation in which the

tool axis can be changed according to the side to
be machined, by using various strategies.
The Multi-Axis Flank Contouring operation is

especially useful for machining the flanks of the
structured parts used in the aerospace industry.
Collision with the drive surface can be avoided.
In Multi-Axis Contouring operation, you can

change the local feedrates while machining along
the area.

Student Notes:
Multi-Axis Flank Contouring: General Process
1 Specify the Name of the operation.

(optional, because a default name is given 1
by the system ‘Type_Of_Operation.X’) 2
3
2 Type text of comment, if needed.
3 Define the operation parameters using the 5 tabs.
Strategy tab
Geometry tab
Tool Definition tab
Feeds & Speeds tab
Transition Paths tab
4 Replay and/or Simulate the tool path.

4
5 5
Click OK to create the operation.

Student Notes:
Multi-Axis Flank Contouring: Geometry

You will see the options on the Geometry tab of Multi-Axis Flank Contouring.

Student Notes:
Presentation
The Geometry tab includes a sensitive icon dialog box

that allows the selection of:
Drive Surface elements A

Flank tool will lean on Drives
With respect to tool axis strategy and offset E
Part Surface elements B A

Tool end will lay down on Part
With respect to tool axis strategy and offset D C
B
Start element C
Used to compute the initial tool position
Stop element D
Used to compute the final tool position
Check elements (optional) E

Elements to avoid during machining

Offset can be applied on part, drive,
check and along tool axis

Student Notes:
Drives Elements (1/3)
Face selection:
This wizard allows you to quickly select
drives.
To start the navigation, you always

need to select at least two faces
(first one is start element, second one
gives the direction to navigate).
Then you can select

Navigates on belt of faces: Navigation
is done in order to follow a belt or
You can select

Navigates on Faces Until a Face:
Navigation is done until
a selected face.
You can use

Multi-selection of Face: Multi-selection
of faces is possible when selecting
drive elements.

Student Notes:
Local Modifications:
(contextual menu on drive elements)
This task illustrates how to locally modify a
Multi-Axis Flank Contouring operation in the
program.
Once all drives are selected, you can modify
locally strategy and offset on each drives.
Drive surfaces properties dialog box:
Select this icon to open the drive editor


Student Notes:
Local Modification Wizard

Browser on drive:
select the drive on which
you want to perform modification
(selected drive is highlighted)
Local offset modification
Local Tool axis guidance modification
In case of non- contiguous drives
ability to define locally on each
drives Start, Stop and positioning
conditions.
Drive element 2
Restart = LEFT
Stop = TO
Tool side = SWAP

Drive element 3 Drive element 1
Restart = LEFT Stop = PAST

Student Notes:
Part Elements (1/2)
Use curves as part:

A curve can be selected as a Part surface.
Click right (MB3) on part element sensitive
icon and select ‘Use curves as part’
The system accepts only curves
that are boundary of selected drives.
Edge selection:
This wizard allows you to quickly select the
curves
To start the navigation, you always need to
select at least two edges
(first one is start element, second one give
the direction to navigate).
Then you can select
Navigates on belt of edges:
Navigation is done in order
to follow a belt or
You can select
Navigates on Edges Until an Edge:
Navigation is done until a
selected face

Student Notes:
Part Elements (2/2)
Use curves as part: example
Part = curve
Tool can cross curve
Better Cutting tool condition
Part = bottom
Tool do not cross bottom
Cutting tool condition not
optimized

Student Notes:
Start and Stop Elements (1/2)
Start and Stop elements must be a surface, a plane, an edge or a vertex.

Start element
The algorithm needs to know
a start position. This position is
computed using the first selected
drive and the start element.
Stop element
As for the start element, this position is
computed using the last selected drive and
the stop element.
Start/Stop Conditions
Positioning of the tool is automatically Drive element
computed. But it can be modified using right-
click on « start » or « stop ».
An offset can be applied. IN OUT Tgt
Machining way ON
Start or Stop element

In 15 mm Out 20 mm

Student Notes:
Start and Stop Elements (2/2)
Closed Pocket trick:

Start and Stop
Select top edge from Drive.1 as Start and
Stop element (ON option).
Algorithm is automatically computing

middle point of this edge then creating a
virtual plane normal to drive at this point.
Thus you can start on Drive 1.
Do not forget to activate Close Tool path

option.

Student Notes:
Multi-Axis Flank Contouring: Strategy

You will become familiar with Strategy Tab of Multi-Axis Flank Contouring.

Student Notes:
Machining Tab (1/2)
Machining tolerance
Value of the maximum allowable
distance between theoretical
tool path and the computed tool path.
Max discretization step and angle

Maximum distance and angle between
two outputted points of tool path
(default values are infinite, different settings
have to be done according to post-processor
and machine feature).
Close tool path

Option to activate in closed pocket
when the first drive element is used
as last drive.

Student Notes:
Machining Tab (2/2)
Maximum distance between steps Click here to select Tool Axis
Rough estimated distance used by the

algorithm to search for next drive or Click here to select
normal to planar 4X
check element (In most of cases do
constraint
not modify this parameter)
Reference point and Manual direction

A This point is automatically computed
(using first drive, part and start element)
But in particular geometric cases it
could have to be manually defined.
B Using a reference point, direction can
be automatic, right or left:
A
Drive surface
Left direction Right direction

Tool B
Reference point

Student Notes:
Stepover Tab (1/2)
Tool path style:

Zig zag or one way
Zig zag One way
Sequencing
Radial or Axial priority
Radial priority Axial priority

Student Notes:
Stepover Tab (2/2)
Radial strategy
Define the distance between paths and
the number of paths
Axial strategy
Select the mode by offset or by thickness
By offset: tool path is

computed once then By thickness: tool
an offset along axis is path is re-computed
applied for each level for each level
Define the distance between paths and the number of levels


Student Notes:
Finishing Tab (1/2)
Mode
No side finish Side thickness
Side thickness
on bottom
At last level
Side thickness
At each level
Side thickness
on bottom
At bottom
Each side and bottom finishing strategies can be combined:

At each level and bottom At last level and bottom

Student Notes:
Finishing Tab (2/2)
Mode At last level
No side finish
At each level
Side thickness Side thickness

on bottom
At bottom
Side thickness Side thickness
on bottom
Each side and bottom finishing strategies can be combined as follows:

At each level and bottom At last level and bottom

Student Notes:
Tool Axis Tab (1/12)
All Guidance Definitions:
Guidance Definition
This is the basic strategy which ensures good continuity through the different tool
Tanto Fan motions. It is less used for flank contouring in structural parts as you don’t control
collision with the drive. To a safety use, add a guiding curve.
Combin Tanto This strategy ensures that the tool stays normal to the Part in the forward direction
with a fanning at the beginning and at the end of the tool motion. This strategy is
good for circular and planar drive surfaces where the isoparametric curves are not
proper (incline isopararimetric) to force the tool to have a minimum lead angle.
This strategy ensures you that the tool will follow the “isoparametrics” of your
Combin Parelm
surface with a fanning at the beginning and at the end of the tool motion.
It is the strategy to use when the isoparametric of the drive surfaces have a good
orientation.
This strategy provides a COMBIN TANTO on planar and cylindrical rsur and a
Mixed Combin COMBIN PARELM in other cases. It is the better strategy in most of the cases for
structural part flank contouring.
Fixed axis The tool axis is fixed to a defined direction.
Normal to part The tool stays normal to the part surface.

Student Notes:
Guidance: Tanto Fan

Tool is tangent to the drive surface
at a given contact height. Interpolation between
Tool axis is the interpolation start and end position
between the start and end positions.
Tool tangent to
the drive at a
given contact
height point.
The contact height is used to determine

a point on the drive surface where the tool
must respect tangency conditions.
Default value is zero and is related to
the bottom of the tool.
Tanto Fan: This is the basic strategy which ensures good continuity through the different
tool motions. It is the less used strategy for flank contouring in structural part as you can’t
control collision with the drive. To a safety, use add a guiding curve.

Student Notes:
Tanto Fan Guidance illustration:
Start Position =
Stop Position = Intersection between
intersection between Start plane and Drive.1
Stop plane and Drive.1
Interpolation between
start and end position
In this example, Start/End Position are defined using planes (manually created).

Student Notes:
Tanto Fan Guidance illustration:

Start Position =
Intersection between
edge and Drive.1
Stop Position =
intersection between
edge and Drive.1
Interpolation between
start and end position
Same example, but Start/End Position are defined using edges of Drive.1

Student Notes:
Guidance: Combin Tanto

= Tanto Fan (during leave distance) + Tanto + Tanto Fan (during approach distance)
Tanto guidance definition: (exists alone only as a local mode)
Tool is tangent to the drive surface at a given contact height.
Tool Axis contained in a plane normal to forward direction
Approach and leave distance parameters can be modified
If approach=leave=0, then Combin Tanto = Tanto
Tanto Fan Tanto Tanto Fan
Approach fanning distance Leave fanning distance

Combin Tanto: This strategy ensures that the tool stays normal to the Part in the forward direction
with a fanning at the beginning and at the end of the tool motion.
This strategy is good for circular and planar drive surfaces where the isoparametric curves are not
proper (incline isopararimetric) to force the tool to have a minimum lead angle.

Student Notes:
Combin Tanto Guidance illustration:
Tanto Fan Tanto Tanto Fan

Leave fanning
Approach distance
fanning distance

Student Notes:
Guidance: Combin parelm

= Tanto Fan (during leave distance) + Tanto Parelm + Tanto Fan (during approach distance)
Tanto parelm guidance definition:
The tool axis is tangent to the drive surface at the specified contact height
and follows the isoparametrics of the Rsur
Approach and leave distance parameters can be modified:
If approach=leave=0 then Combin parelm = Tanto parelm
Tanto Fan Tanto Parelm Tanto Fan

Approach fanning distance Leave fanning distance
Combin Parelm: This strategy ensures you that the tool will follow the “isoparametrics” of your
surface with a fanning at the beginning and at the end of the tool motion.
It is the strategy to use when the isoparametric of the drive surfaces have a good orientation.

Student Notes:
Tip: how to see “isopar” in V5

Tools/Options/General/Display/Performances/ Enable isoparametrics generation = ON
Restart CATIA
View/Render Style/Customized View/ Isoparametrics = ON

Student Notes:
Combin Parelm Guidance illustration:
Isoparametrics (u, v)
Tanto Fan Tanto Parelm Tanto Fan

Leave fanning
Approach fanning distance
distance

Student Notes:
Guidance: Mixed Combin

This strategy is equivalent to Combin Parelm except on planar or cylindrical
surfaces on which Combin Tanto strategy will be applied (as isoparametrics
direction may not be appropriate to follow on this kind of surface)
Approach and leave distance parameters can be modified
Combin Parelm
Combin Tanto
For other drive surfaces

Combin parelm is used For cylindrical and
planar drive surfaces
Combin Parelm Combin Tanto Combin Tanto is used
Mixed Combin: This strategy provides a COMBIN TANTO on planar and cylindrical
rsur and a COMBIN PARELM in other cases.
It is the better strategy in most of the cases for structural part flank contouring.

Student Notes:
Guidance: Fixed Axis

Tool Axis is fixed
Click here to select Tool Axis

Fixed axis: The tool axis is fixed to a defined direction.

Student Notes:
Guidance: Normal to part

Tool Axis is normal to selected part while the tool remains in contact with Drives
Normal to the part: The tool stays normal to the part surface.

Student Notes:
Other Parameters (1/5)
Disable fanning:
All guidance with fanning (Combin Tanto, Combin parelm and Mixed
Combin) can be benefited from disable fanning option.
This option is available on Start, Stop or both.
Tool axis start
position with
fanning
Tool axis start
position without
fanning
Disable fanning is an easy way to select

start/stop elements connected to machined
geometry (edges, rsurs) to keep associativity
without unexpected fanning motions.

Student Notes:
Disable fanning illustration

5 axis open pocket with draft wall
Combin parelm strategy with multi axial levels (0,1, 2)
Stop element =
Stop element=bottom edge
edge on draft wall
=> levels 1 and 2 outside : KO!
level 0 inside
level 2 outside
KO !
Stop element = Stop element =

Rsur draft wall Rsur draft wall
unexpected + disable fan on stop
fanning : KO !
+ Axial strategy: by
thickness
end tool path OK !
Tool axis OK !

Student Notes:
Useful cutting length
Fanning algorithm is using tool cutting length parameter.
If needed to control fanning, this parameter can be modified with this option.
Intersection point between cutting length

and stop element extrapolation
=> Fanning motion starts
Fanning motion start expected point
Cutting length
Stop element extrapolation
Stop element
Drive
Approach fanning
distance: not respected !!

Student Notes:
Local Tool axis guidance

Two axis guidance are available only in local
modification.
Tanto guidance
Tool is tangent to the drive surface at a
given contact height. Tool Axis contained in
a plane normal to forward direction.
In the example, Global guidance is

Combin parelm, which means Tanto
Parelm on drives (except fanning motions).
Then on this, drive guidance will be Tanto.
Thus, it is possible to enable 4 axis

mode and force Tool axis to be in a
manual 4 axis Plane.

Student Notes:
Auxiliary guiding element

This curve is a tool axis strategy
modifier. This modifier is used to modify
tool axis to avoid collision with Drive Surface.
It moves the tool away in the correct
direction according to position on guide
curve parameter.
Auto, Left, Right, On values
It is possible to define offset on guide

curve.
Always use will force algorithm to
always use guide curve.
If needed, algorithm will use guide curve

only in case of collision.

Student Notes:
HSM Tab
Cornering and cornering on side finish path

Allow the user to define a cornerisation
of the tool path by giving a corner radius
Feed and Speed Tab

Feed- rate reduction in corners
Applied inside corners for machining
and finishing passes.
Not in macros or default linking and
return motions

Student Notes:
Compensation (1/2)
Cutter compensation parameters: Allow you to manage generation of cutter

compensation (CUTCOM) instruction in the NC data output
3D radial (PQR):
3D radial compensation data (Vector <P,Q,R>) can be generated in the APT
output. The Radial compensation data output can be activated or not on each
Multi Axis Flank Contouring cycle of a program. For all tool positions of the
machining passes, for the last motion of each approach macro, and for the first
motion of each retract macro, the <PQR> vector is added to the APT statement
(which contains the Tip position and the Tool Axis.
Before the first position with <PQR> data, two APT statements:
CUTCOM/SAME,NORMDS and CUTCOM/NORMDS are automatically added, after
the last position with <PQR> data, a CUTCOM/OFF statement is automatically
added. These PQR statements are supported and can be translated by Multi-Axis
Post Processors provided NC manufacturing Workbenches.
2D Radial- TIP (G41/G42) :

The tool tip will be visualized during tool path replay. Cutter compensation
instructions are automatically generated in the NC data output. An approach
macro must be defined to allow the compensation to be applied.
None:
Cutter compensation instructions are not automatically generated in the NC data
output. However, CUTCOM instructions can be inserted manually.

Student Notes:
Compensation (2/2)
Compensation output sum up


Student Notes:
To Sum Up
In this course you have seen:
Necessary geometrical elements to define a Flank Contouring operation

Drives
Navigation on drives, local modification on drives, non- contiguous drives
Parts (can be a curve)
Multi part
Start/Stop
Open or closed pocket
5 Axis strategies of Flank Contouring operation

Tanto Fan, Combin Tanto, Combin Parelm, Mixed Combin, Fixed axis, Normal to part, 4-Axis
Stepover management
Multi-radial
Multi-axial with thickness or offset
Side and bottom finishing strategies
HSM option
Output: Compensation

Student Notes:
Multi-Axis Helix Machining

You will become familiar with the 5 axis Helix Machining principles.
Introduction
General Process
Geometry
Strategy
To sum Up

Student Notes:
About Multi-Axis Helix Machining
Multi-Axis Helix Machining operation is mainly used

for semi-finishing and finishing of blades and blisks
in turbo-machinery parts.
Collision checking is possible on cutting part of the
tool or on the tool assembly.
Tool Axes can be defined manually in order to have
better control on tool and collision can be avoided
with neighboring blades.
You can use Multi-Axis Helix Machining operation to
generate a single helix toolpath to mill an entire
turbo-machinery blade.

Student Notes:
Multi-Axis Helix Machining: General Process
1 Type the Name of the Operation.

(optional because a default name is given 1
by the system ‘Type_Of_Operation.X’)
2
3
2 Type text of comment (optional).
3 Define operation parameters using the 5 tab pages.
Strategy tab
Geometry tab
Tool Definition tab
Feeds & Speeds tab

4

Student Notes:
Multi-Axis Helix Machining: Geometry

You will become familiar with the options on the Geometry tab of Multi-Axis Helix
Machining.

Student Notes:
Presentation

Part elements A
blade body surfaces
Upper contour B B
limiting element on top of blade
Lower contour C
limiting element on bottom of blade D
A E
Leading edge D
Trailing edge E
Check element (optional) F
elements to avoid during tool path C

F
Offset can be applied on both, part and check.

Student Notes:
Part Elements
Face selection:
This wizard allows to select quickly part
elements
To start the navigation, one always need

to select at least two faces
give the direction to navigate).
Then select
Navigates on faces
Navigation is done on all adjacent faces.
or
Navigates on belt of faces

to follow a belt or
Navigates on Faces Until a Face

a selected face.

Student Notes:
Upper and Lower Contours (1/2)
Edge selection:
This wizard allows to select quickly contour
elements
To start the navigation, one always need

to select at least two edges
give the direction to navigate).
Then one can select

Navigates on belt of edges
to follow a belt.
or
Navigates on Edges Until an Edge

a selected edge.

Student Notes:
Upper and Lower Contours (2/2)
Upper and lower contour may be already prepared in NC geometry CATPart.

NC programmer will just have to select it in PPR Tree or in CATIA window
There is no check on contour

selection. Bad contour selection may
lead to strange tool path.
all contour may lie down on surfaces.
do not select twice the same element.
global contour must be closed.

Student Notes:
Collision Checking
Choose if collision checking is applied on cutting part of the tool (only lc=cutting
length) or on the whole assembly (cutting part + shape + holder)
Activate or not on Part
Accuracy is by default initialized with machining tolerance
Defines the maximum error to be accepted
Allowed gouging need to be set
Defines maximum cutter interference
Set accuracy and allowed gouging on Check tab
Collision checking may have impact on tool path computation time.

See tool axis variable mode (next foils) to know what is done in case of detected collision.

Student Notes:
Multi-Axis Helix Machining: Strategy

You will see the Strategy Tab of Multi-Axis Helix Machining.

Student Notes:
Machining Tab (1/3)
Machining tolerance
distance between the theoretical
Max discretization step and angle

Maximum distance and angle between
two outputted points of tool path
(default values are infinite, different settings
have to be done according to post-processor
and machine feature).
Direction of cut
Climb: The front of the advancing tool
cuts into the material first.
Conventional: The back of the advancing

tool cuts into material first.

Student Notes:
Machining Tab (2/3)
Start and Stop Element Mandatory
One must define a start element (a point) and
optionally a stop element (a point)
Start point may be pre-defined
For example use one extremity of contour
near trail or lead edge or
Create this point and save it in NC
geometry CATPart.
Optional
Start point may be create on the fly

Use MB1 button on part surface to indicate a
point. It will be projected on closest contour
by algorithm.

Student Notes:
Machining Tab (3/3)
4 axis-tilt plane
Define machine frozen plane with
sensitive plane in picture
Tool axis
Define or modify default tool axis, select
sensitive axis in picture

Student Notes:
Radial Tab (1/2)
Scallop height stepover

Set the maximum scallop
height allowed between two
paths
Distance between turns stepover

Set the distance between two
paths
Number of turns stepover

Set a number of turns
Always start with easy strategy in order to

roughly validate your work.
For example start with Nb of turn=10

Student Notes:
Radial Tab (2/2)
Skip path
In case of machining a part with
more than one operation, this option
allows to have a better transition
between each operation.
First, Last or First and last

Student Notes:
Tool Axis Tab (1/6)
Lead and tilt

For each computed tool path point: local
normal at the surface is computed then:
Lead angle is set (forward / backward)
Tilt angle is set (right/left)
Tilt angle Lead angle
4 axis–tilt
Define machine frozen plane with sensitive
plane in picture
According to normal at this plane:
Tilt angle is set (right/left)
Lead angle is set (forward/backward)

Student Notes:
Tool Axis Tab (2/6)
Lead and tilt variation type

Once lead and tilt strategy is chosen, in
case of collision checking activated two
degraded modes are available:
1. Variable lead and fixed tilt -
Set the reference Lead Angle
Set the fixed Tilt Angle
Set the max and min allowed lead
In this example, reference lead is 9°

and could change from 8°to 15°.
Change in lead would be performed if collision checking is active Variable lead mode is dedicated
(part and/or check) and algorithm can compute a better tool to avoid collision between tool
position using the allowed change in Lead angle. rear side and part.

Student Notes:
Tool Axis Tab (3/6)
2. Fixed lead and variable tilt -
Set the fixed Lead Angle
Set the reference Tilt Angle
Set the allowed tilt
In this example, reference tilt is 35°

and could change from 25°to 45°.
Change in lead would be performed if collision checking is active Variable tilt mode is dedicated to
(part and/or check) and algorithm can compute a better tool ball-end tool machining with risk
position using the allowed change in Tilt angle. of collision between tool shape
and part.

Student Notes:
Tool Axis Tab (4/6)
Interpolation
This Tool Axis strategy allows to manually
define axes in order to have a better
control on tool.
This strategy is very useful to avoid
collision with others blades.
By default, 4 axes are initialized. You can remove

or edit these axes and you can add more axes. List of default Interpolation axes

Student Notes:
Tool Axis Tab (5/6)
Interpolation: adding / modifying (editing) axes

Select existing axis and adjust parameters in dialog box or select existing
pre-defined axis (previously created and store in Ncgeometry CATPart).
In each case one can use Display tool option to control collision.
During axis selection, you can put the compass at the top of the tool (as
shown) to adjust roughly the tool axis.
OR

Student Notes:
Tool Axis Tab (6/6)
Lead and tilt variation type

Keep in mind following points
A Degraded mode (variable tilt or variable lead) are applied only if collision
checking is active.
B Degraded mode may lead to abrupt tool axis variation and have to be
checked with machine capabilities.
C Collision checking may have impacts on tool path computation time.
B
A
C

Student Notes:
To Sum Up
In this course you have seen:

Necessary geometrical elements to define a Multi-Axis Helix Machining
Part
Contour
Lead and trail edges
Start point
5 or 4 Axis strategies of MX Helix

Lead and tilt (degraded mode available), 4 axis tilt and Interpolation
Step over management

Maximum scallop
Distance between path
Number of turns

Student Notes:
Cavities Roughing
You will become familiar with the Cavities Roughing principles.
Introduction
General Process
Geometry
Strategy
To sum Up

Student Notes:
About Cavities Roughing
Cavities Roughing is mainly used for

roughing of Aerospace structural parts.
You can rough machine a part automatically
or you can manually select the zones.
Imposed planes can be inserted to facilitate
the forced machining at those levels.
Limiting Contour is useful for roughing and
You can use Mask methodology after
completion of roughing.
Offset Management can be efficiently done
with the available functionalities in Cavities
Roughing.
In Cavities Roughing, you can select the
area as Outer only, Pockets only or Outer
and Pockets. It is possible to leave the
thickness on sides and horizontal areas.
Small pockets in the part can be filtered.

Student Notes:
Cavities Roughing: General Process
1
Type the Name of the Operation. 1
(optional because a default name is given
2
by the system ‘Type_Of_Operation.X’)
3
2 Type text of comment (optional).
3 Define operation parameters using the 5 tab pages.
Strategy tab
Geometry tab
Tool Definition tab
Feeds & Speeds tab

4

Student Notes:
Cavities Roughing: Geometry

You will become familiar with the options on the Geometry tab of Cavities Roughing.

Student Notes:
Presentation (1/2)

A and B : Rough Stock and Part

Cavities Roughing operation will remove all A
stock material in order to obtain final part.
Offset can be applied on part.
D
C : Check (optional)
Elements to avoid during machining. Offset
can be applied on check.
D and E : Top and Bottom planes

C
Define them to limit height machining. B
E

Student Notes:
Presentation (2/2)
F
: Imposed planes (two group)
Force cutter to machine in this plane (global
offset can be applied on each group).
G I
: Limiting contour
Re-limit machining area after stock and part
Definition.
G
H : Center zone order

Define pocket machining order.
F
I : Start Point (optional)

Impose start point in open area (not in pocket)
H

Student Notes:
Geometry (1/9): Rough stock and Part
Rough Stock and Part definition example:
ROUGH STOCK
FINAL PART

Student Notes:
Geometry (2/9): Rework Capability
Rework definition:
Stock definition can be either at Part Operation level or Operation level. To benefit
from rework capability, don’t define stock at operation level.
Therefore algorithm will compute ‘actual stock’ taking care all previous operation
defined (even non Cavities Roughing operation)
Do not forget to select Force Replay button to update this ‘actual stock’ if needed.
It is recommended to use helical strategy for rework computation in order to have
an optimized toolpath.
Minimum thickness to machine parameter:

When using rework capability one can use this parameter that specify the
minimum thickness taken into account for computation.

Student Notes:
Geometry (3/9): Outer Part And Pocket Area
Outer part and pocket definition:
Pocket area: all area tool contouring

Pocket Area
is touching the part.
Outer area: all area which is not

pocket area. Outer Area
Outer part and pocket notes:
It is not only a geometrical concept. It

is a function of: Part, Tool diameter
and Stock.
Be careful, part can be composed of

different elements depending of tool
diameter. A pocket can become an
outer part…see next foil.

Student Notes:
Geometry (4/9): Important Note
Tool diameter impact on outer and pocket area:

Part
Stock
All area tool contouring is

touching the part. Hence it
is a pocket area.
Outer part area
Pocket area
Same geometry but with a

smaller tool diameter, this
time all area tool contouring
is touching the part and the

stock, so it’s an outer area.

Student Notes:
Geometry (5/9): Z Level Plane Impact On Area
Example:
Cut plane 1
Cut plane 2
Cut plane 1
Outer part area
Cut plane 2
Outer part area

Pocket area

Student Notes:
Geometry (6/9): Limiting Contour
Limiting contour is used to restrict machining area to dedicated pockets.

One must define a closed contour with Edge selection wizard then specify
Side to machine (inside or outside) and stop position.
Line selection: This wizard allows to select

quickly contour elements (navigation).
Rough Stock
Offset = 0mm Side to machine :
outside
out in
on on Restricted Area
in out Inside
Side to machine : Outside
Inside Final Part
Offset = 0mm
Offset = 5mm Offset = - 5mm
out
on Offset +
in
out
on Offset -
in Positive Offset => offset to outside
Side to machine : Negative Offset => offset to inside
Inside Side to machine: Inside

Student Notes:
Geometry (7/9): Mask Methodology
It is not advisable to use limiting contour to describe the part at the end of roughing.
Here the mask methodology is preferred:
Define a mask surface (describing the part at the end of roughing) and select it
as part in the user interface.
Limiting Contour MASK
Final Part
Final Part
Rough Stock
Rough Stock
Negative points: Positive points:

Limiting contour can be crossed by tool tip
Part elements are not

Limiting contour impact on outer and part area necessarily connected.
Need to manage offset
Offset is function of Tool diameter, thickness
on part.

Student Notes:
Limiting Contour impact on outer and pocket area:

Part
Stock
Outer part area
Pocket area
Limiting Contour
Blue zone is still an outer part

area, because tool contouring
cannot be performed only by
touching the part.

Student Notes:
Mask impact on outer and pocket area:

Part
Stock
Outer part area
Pocket area
Stock
Mask (selected as Part)
In this case (Mask = Part);

tool contouring is performed
only by touching the part so
it’s a pocket area.
Using Mask definition, open

pocket is transformed in a
pocket area.

Student Notes:
Planes (1/4): Top and Bottom Planes
Top and Bottom Planes offer capability to restrict height of

machining area.
These planes are used in cut depth computation.

(see Strategy Tab chapter)
Restricted machining area


Student Notes:
Planes (2/4): Imposed Planes
Top and bottom planes with maximum depth of cut allow to define cutting planes.
Adding to them, it is possible to define Imposed cutting planes, manually or using auto
search on part. Imposed planes are the planes to which the cutter must positively reach.
TOP (Z=30)
Initial step: top and bottom planes selected, Cut1 (Z=21.7) 8.3
max. depth of cut = 10
=> 3 Cut plane automatic computation Cut2 (Z=13.3) 8.3
Cut3 (Z=5) 8.3

BOTTOM (Z=5)

Student Notes:
Planes (3/4): Imposed Planes
Adding imposed plane with search plane capability:
Select right mouse button on imposed plane sensitive picture then select Search/View
menu, the window as shown below will be displayed:
TOP (z=30)
7.3
Cut1 (z=22.7)
7.3
Z= 8 imposed plane added Cut2 (z=15.3)
7.3
=> Cut plane 1 and 2 re-computed,
extra cut (z=8) added. Extra Cut3 (z=8)
3
Cut4 (z=5)
Bottom (z=5)

Student Notes:
Planes (4/4): Notes
Offset:
All planes (top, bottom, imposed) can be modified using offset capability.
Cutting plane will always strictly respect the offset plane.
Two groups of imposed planes are existing in sensitive picture thus allowing to define
two different offsets on imposed planes.
Adding Imposed Plane with Search/View capability:

Scanning is performed on all planar surfaces of the part or only the planes that can be
reached by the tool you are using (small pockets and counter-draft area are skipped)
Be careful, offset on imposed planes has to be greater than the global offset on part,
otherwise it will not be respected.
Adding imposed plane manually:

Any plane can be selected (physical part plane, plane created in WFS workbench etc)
Selection:
System automatically check if selected plane is normal with tool axis (e.g. if plane
selection is refused, check operation tool axis)

Student Notes:
Start Point And Zone Order
Start point restrictions:
Only for outer part area (no pocket).

Only helical mode.
Defined point must not be in collision with Part
or Stock.
Start point

Student Notes:
Zone Order
Zone order definition :

It is a capability to define pocket order machining
(either outer part or pocket).
It is used to manage stress on part for example.
Pocket
Zones will be machined in the selected order.
It is possible to machine only selected zones.
(MB3 on Zone Order)
Outer Part
Zone Ordering

Student Notes:
Cavities Roughing: Strategy

You will learn the options in the Strategy Tab of Cavities Roughing.

Student Notes:
Presentation
This Tab Page allows to define:
Thicknesses on sides and horizontal area.

Offset Management in detail.
Machining, Radial, Axial, HSM and Zone tabs.
Tool axis and cutting directions
(sensitive picture).

Student Notes:
Center Definition (1/3)
‘Center’ is roughing the part by leaving

thicknesses on sides and horizontal areas.
One can define remaining

thickness on sides.
And minimum thickness

on horizontal area
In Back and Forth strategy, machining

direction can be set manually using axis
definition dialog box. It can be set OR
automatically using optimize option (right

mouse button menu).

Student Notes:
Machine horizontal areas until minimum thickness

option:
Depending on cutting plane computed, horizontal area may

have till one cut depth remaining material. This cut depth
can be machined by using ‘Machine horizontal areas until
minimum thickness.’
If this option is activated, it will force

to have one extra path on this
horizontal area to respect minimum
thickness.

Student Notes:
Bottom plane = bottom of
pocket + 2mm offset
Machine horizontal areas until minimum
thickness example:
10 mm
2 mm
2 mm
Machine horizontal areas until

minimum thickness - Not activated 2 mm 2 mm
2 mm
Machine horizontal areas until

minimum thickness - Activated

Student Notes:
Offset Management: Case 1- Part Offset
Parameters:
Part offset =1mm (blue) forbidden to go under this value
Max depth of cut = 3mm
Computed planes
Condition to be respected:
Each 3mm
Offset on each horizontal area part offset
Z=45
2mm 2mm
13x3mm
6x3mm
Z=40 9x3mm
8x3mm
6
Z=35
11x3mm
Z=30
Offset=2mm
Z=25
Offset=1mm
Z=20 2 Offset=3mm
Z=15
Offset=2mm
4
Z=10 3
Offset=1mm
Z=05
1
Z=00 5
Compute of the remaining material depth on horizontal areas =

H-D*N Part offset + Min thickness on horizontal areas
H : depth to remove
D : max depth of cut
N : number of level

Student Notes:
Offset Management: Case 2 - Minimum thickness on
horizontal areas
Parameters:
Computed planes
Offset on each horizontal area part offset +
Each 3mm
Min thickness on horizontal areas (1.5mm)
Z=45
2mm 2mm
12x3mm
6x3mm
Z=40 9x3mm
7x3mm
6
Z=35
11x3mm
Z=30
Offset=2mm
Z=25 Offset= 4mm
Z=20 2 Offset=3mm
Z=15
Offset=2mm
4
Z=10 3 Offset= 4mm
Z=05
1
Z=00 5
Compute of the remaining material depth on horizontal areas =

H-D*N Part offset + Min thickness on horizontal areas
H : depth to remove
N : number of level

Student Notes:
Offset Management: Case 3 - Machine horizontal areas until
minimum thickness
Parameters:
Computed planes
Each 3mm
Offset on each horizontal area = part offset +
Z=45
1.5mm 1.5mm
Z=40
6
Z=35
Z=30
Offset=1.5mm
Z=25
Offset= 1.5mm
Z=20 2 Offset=1.5mm
Z=15
Offset=1.5mm
4
Z=10 3
Offset= 1.5mm
Z=05
1
Z=00 5
Compute of the remaining material depth on horizontal areas = Added plane to reach 1.5 mm
Part offset + Min thickness on horizontal areas On each horizontal area
H : depth to remove
N : number of level

Student Notes:
Offset Management: Case 4 - Bottom Plane
Parameters:
Computed planes
Define bottom plane with 0.5mm offset (Z=15.5)
Each 2.95 mm
Z=45
2.05mm 2.05mm
6x2.95mm
9x2.95mm
7x2.95mm
Z=40
6
Z=35
Z=30 2.3mm
Z=25
4.35mm
Z=20 2 3.45mm
5.5mm 4 10.5mm
Z=15
Z=10 3
Z=05
1
Z=00 5
1. Recomputed depth to have regular depth of cut: H( top-bottom)/N closest
Added plane to reach

than max depth of cut = 2.95 mm bottom plane (+ offset on
2. Compute of the remaining material depth on horizontal areas part offset + bottom)
Min thickness on horizontal areas
H (top-bottom): depth to remove from top of the stock to bottom plane
N: number of level
The bottom path is done only in zones 1 & 5.

Student Notes:
Offset Management: Case 5 - Imposed Plane
Parameters:
Computed planes
Define Imposed plane with 0.5mm offset (Z=20.5)
Each 2.72 mm
Z=45
2.28mm 2.28mm
6x2.72mm
9x2.72mm
8x2.72mm
Z=40
6
Z=35
Z=30 3.66mm
Z=25 3.22mm
Z=20 2 2.57mm
Z=15
1.71mm 4
Z=10 3 3.78mm
Z=05
1
Z=00 5
Computed planes
Each 2.93mm
1. Recomputed depth to have regular depth of cut between imposed planes
until imposed plane: Recompute depth: H (top-imposed plane)/N closest than max depth of cut = 2.72 mm
after imposed plane: Recompute depth: H (imposed plane-last plane)/N closest than max depth of cut =
2.93 mm
2. Compute of the remaining material depth on horizontal areas part offset + Min thickness on horizontal
areas
N : number of level
The imposed plane path is done only in zones 1, 3 & 5.

Student Notes:
Offset Management: Case 6 - Top Plane
Parameters:
Computed planes
Define Imposed plane with 1mm offset (Z=35)
Each 2.92 mm
5mm 5mm
Z=45
2x2.92mm
Z=40
6
8x2.92mm
5x2.92mm
Z=35
4.16mm
7x2.92mm
8x2.92mm
Z=30
Z=25 3.32mm
Z=20 2 2.48mm
Z=15
1.64mm 4
Z=10 3 3.72mm
Z=05
1
Z=00 5
1. Recomputed depth to have regular depth of cut between top and bottom planes (here = 2.92mm)
2. Compute of the remaining material depth on horizontal areas part offset + Min thickness on horizontal
areas.
N : number of level
The zone 6 is not machined because there are upper top plane.

Student Notes:
Offset Management: Case 7- Mix Case
Parameters:
Computed planes
Define Imposed plane with 0.5mm offset (Z=20.5)
Added plane to
horizontal area
Each 2.72 mm
Define bottom plane with 1 mm offset (Z=11)
reach 1.5 mm
On each
Offset on each horizontal area = part offset +
Z=45
1.5mm 1.5mm
Z=40
6
Z=35
Z=30
1.5mm
Z=25
1.5mm
Z=20 2 1.5mm
Z=15
1.5mm
4
3 6mm
Z=10
Z=05
1
Z=00 5
Computed planes
1. Recomputed depth to have regular depth of cut between imposed planes Each 2.83mm
until imposed plane: Recompute depth: H (top-imposed plane)/N closest than max depth of cut = 2.72 mm
after imposed plane: Recompute depth: H (imposed plane-bottom plane)/N closest than max depth of cut = 2.83 mm
2. Compute of the remaining material depth on horizontal areas = part offset + Min thickness on horizontal areas
The imposed plane path is done only in zones 1, 3 & 5. Bottom plane is done only in zone 5.
Machine horizontal area 4 paths are done in different zones (1st: zone1, 2nd: zone2, 3rd: zone3, 4th: zone4, 5th: zone6)

Student Notes:
Machining Tab (1/7)
Machining tolerance
distance between the theoretical
Direction of cut definition:

Climb: The front of the advancing tool
cuts into the material first
Conventional: The back of the

advancing tool cuts into material first
Machining mode (refer to outer part and

pocket area definition):
This option allows to select geometry
machining between-
Outer part and pocket,
Pockets only and
Outer part
Sequencing :
By plane or
By area

Student Notes:
Machining Tab (2/7)
Tool path style: Back and forth

Tool is moving following selected direction.
The machining direction is reversed from one path to the next.
Optimize option let the algorithm

choosing direction in order to minimize
change of direction in tool path.
The contouring passes can be applied Prior or After the back

Tool path with
and forth passes.
Back and forth
In ‘Prior mode’ it is possible to define a multi level

contouring pass (in order to manage tool loading).

Student Notes:
Machining Tab (3/7)
Tool path style: Helical

Tool moves in successive concentric passes from
the boundary of the area to machine towards the
interior or from the interior to the boundary.
Helical Movement:
Inward:
Tools start from a point on
zone boundary and follow
concentric passes parallel to
boundaries towards interior.
Tool path with

Helical
Outward:
Tool starts from a point inside
the zone and follow concentric
passes parallel to boundaries.

Student Notes:
Machining Tab (4/7)
Both:
for pockets, the tool starts from a point
inside the pocket and follows outward paths
parallel to the boundary.
for external zones, the tool starts from a Pocket
point on the rough stock boundary and
follows inward paths parallel to the
boundary.
Outer part
Outward
Inward

Student Notes:
Machining Tab (5/7)
Forced cutting mode on part contour:
With ‘Forced cutting mode on part contour’ is

deactivated, outer part in helical inward style,
contouring pass is in Conventional cutting
condition even if Climb cutting mode is
selected.
Option OFF:
Inward
contouring pass is not respecting climb
With ‘Forced cutting mode on contour’ is

activated, contouring pass is now in
climb cutting condition. The tool goes
round the outside contour of the part
before continuing.
Option ON:
Inward
contouring pass now in climb

Student Notes:
Machining Tab (6/7)
Always Stay on bottom:

It is possible when there is no collision and with Linking transitions
tool staying in the machining plane.
The tool to remain in contact with the bottom of the
pocket when moving from one domain to another.
This avoids unnecessary linking transitions.
Option OFF:
Approach macro
Retract macro
2 linking movements
Option ON:
Approach macro
Retract macro
No linking movements

Student Notes:
Machining Tab (7/7)
Tool path style: Concentric

Tool is moving following concentric passes.
Tool removes the most constant amount of
material possible at each concentric pass.
Tool is never fully engaged in material.
Tool path is always respecting given cutting
mode.
Approach macro is only helix one.

Student Notes:
Radial tab
There are four different ways to define distance

between passes:
Overlap ratio
Overlap length
Step over ratio
Step over length
Overlapping:
Overlap ratio: Overlap length:
It is the overlap between two It is the distance between two
passes, given as a percentage passes with respect to a tool
of the tool diameter. diameter ratio recovery.
Stepover
Stepover ratio: Stepover length:
It is the stepover between two It is the maximum distance
passes, given as a percentage between two passes.
of the tool diameter.

Student Notes:
Axial tab
Maximum cut depth:

It defines the maximum depth of cut per axial level.
This value will be respected for each axial level from top
to bottom plane.
Variable cut depths:

It allows to define different values of
maximum depth of cut depending on
axial levels.

Student Notes:
HSM tab
High Speed Milling technological parameter:

In order to be compliant with machine technology, this
parameter allows to avoid corners in toolpath, by
defining the minimum radius of tool path.
It is possible to have a different cornerization on

part contouring (most of the time a smaller one to Corner radius:
reduce rework). It defines the radius of the
rounded ends of passes. The
ends are rounded to give a
smoother path that is
Center cornerization is linked with ‘step over distance’. machined much faster. The
corner radius is not applied
A warning message as shown during Tool path to the finish path.
computation is raised in case of incompatibility
and if the value is set at maximum.
Corner radius on part contouring:
It specifies the radius used for rounding
the corners along the Part contouring
pass of a HSM operation. This radius
must be smaller than Corner radius value.

Student Notes:
Zone tab
Zone definition:
This parameter is acting like a ‘pocket filter’,
which means small pockets will be removed.
To be activated one must define a “non- cutting
diameter (Dnc)” parameter in tool description.
Based on this value the following formula is

applied to define the smallest machinable pocket
length:
XX(mm) = Dnc+D+2 x (machining tolerance)

There will not be machining path in pockets
where tool can’t plunge without respecting
maximum plunge angle.

Student Notes:
To Sum Up
In this section you have seen:
Necessary geometrical elements to define a Cavities Roughing operation

Parts (can be composed of different elements)
Stock
Planes (top, bottom, imposed)
Machining strategies of Cavities Roughing

Helical, Back and Forth, both with HSM option
Radial and Axial strategies


CATIA

Uploaded by

Copyright:

Available Formats

CATIA

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CATIA

Uploaded by

Copyright:

Available Formats

What are the different machining strategies discussed in the document?

What are the different machining strategies discussed in the document?

What elements are necessary to define a Cavities Roughing operation?

What elements are necessary to define a Cavities Roughing operation?

Advanced Part Machining

Copyright DASSAULT SYSTEMES 1

About this course

Objectives of the course

Copyright DASSAULT SYSTEMES 2

Introduction to Advanced Part Machining 6

Copyright DASSAULT SYSTEMES 3

Cavities Roughing: Geometry 74

Copyright DASSAULT SYSTEMES 4

Note: The Master Exercise is provided at the end of the

Copyright DASSAULT SYSTEMES 5

Introduction to Advanced Part Machining

Copyright DASSAULT SYSTEMES 6

AMG includes 2.5 to 5-axis machining technologies

AMG develops machining strategies that optimize

AMG benefits the user for:

Copyright DASSAULT SYSTEMES 7

From drilling… …to complex 5 axis machining

(A) (C) (B)

Copyright DASSAULT SYSTEMES 8

Multi-Axis Flank Contouring

About Multi-Axis Flank Contouring

Copyright DASSAULT SYSTEMES 9

The Multi-Axis Flank Contouring operation is

This is a profile contouring operation in which the

The Multi-Axis Flank Contouring operation is

Collision with the drive surface can be avoided.

In Multi-Axis Contouring operation, you can

Copyright DASSAULT SYSTEMES 10

1 Specify the Name of the operation.

3 Define the operation parameters using the 5 tabs.

4 Replay and/or Simulate the tool path.

Copyright DASSAULT SYSTEMES 11

Multi-Axis Flank Contouring: Geometry

Copyright DASSAULT SYSTEMES 12

The Geometry tab includes a sensitive icon dialog box

Drive Surface elements A

Part Surface elements B A

Check elements (optional) E

Elements to avoid during machining

Copyright DASSAULT SYSTEMES 13

To start the navigation, you always

Then you can select

You can select

You can use

Copyright DASSAULT SYSTEMES 14

Select this icon to open the drive editor

Copyright DASSAULT SYSTEMES 15

Local Modification Wizard

Tool side = SWAP

Copyright DASSAULT SYSTEMES 16

Use curves as part:

Copyright DASSAULT SYSTEMES 17

Use curves as part: example

Copyright DASSAULT SYSTEMES 18

Start and Stop elements must be a surface, a plane, an edge or a vertex.