Potential Energy and Conservation of Energy Potential Energy

8.
Potential Energy and Conservation

of Energy
Potential Energy:
When an object has potential to have work done
on it, it is said to have potential energy, e.g. a ball
in your hand has more potential energy than a
ball on the ground. If you release the ball, gravity
will perform work on the ball and its kinetic
energy will increase. If a spring with a block
attached is compressed, the block has potential
energy because if the block is released, the spring
will perform work on the block and give it
kinetic energy.
• Potential energy is energy associated with
the configuration of two or more objects, e.g.
the ball and the earth or the block and the
spring.
• A force is acting between objects. When the
configuration of the system changes and work
is performed on one of the objects, the
potential energy of the system is transferred to
the kinetic energy of that object.
• If the system returns to the original
configuration, the force between the objects
removes kinetic energy from the objects and
stores it in the potential energy of the
system.
• The amount of work done in the original
change and the reversal are equal in
magnitude but differ by a sign: Wi = −W f
• The force in the system is known as a
conservative force.
Conservative force:
• Can store energy in the system as potential
energy.
• Can retrieve that energy and give it to an
object in the system as kinetic energy.
• Gravitational and spring forces are
conservative forces.
• Friction is a non conservative force. If we let
a block scrape along a rough floor, the
friction force will take kinetic energy away
from the box. However, if we reverse the
block and attempt to put it back in its
original position, we do not retrieve the
energy out of the system. The friction force
has converted the kinetic energy into
thermal energy by heating up the block and
the floor. The thermal energy can not be
turned back into the kinetic energy of the
block.
Properties of Conservative Force:

• The net work done by a conservation force
as the object moves from point #1 to point
#2 and back to point #1 is zero.
#2
W12
#1
W21
W12 = −W21
• The work done by a conservative force in
moving the object from point #1 to point #2
does not depend on the path between the
two points.
W3 #2
W2
W1
#1
W1 = W2 = W3
Example:
A 1-kg ball is thrown at an angle with respect
to the ground to reach a height of 10 m. What is
the work done by gravity between the start of the
motion and the peak height?
h
Fg
• In principle, we can calculate the work done

along the trajectory. However, this is
complicated because the angle between the
direction of motion and the gravity is
changing along the trajectory. Alternatively,
we can use work-energy theorem to calculate
the work done if we can calculate the initial
and final velocity. However, there is a easier
method: use the fact that gravity is a
conservative force to calculate the work done
along the path shown:
Fg
W = W(horizontal path) + W(vertical path)

= 0 − mgh
= −mgh
Potential Energy Calculation:

If a positive amount of work is performed on
the object (the kinetic energy increases), then the
potential energy of the system must decrease:
∆U = −W
Gravitational Potential Energy:

For the ball flying to its maximum height, the
change in potential energy:
∆U = − (−mgh) = mgh
In general, the change in the gravitational
potential energy is given by
∆Ug = mg(y f − yi )
This is the potential energy of the ball-earth
system. We often say that “the ball has X Joules
of potential energy.” However, it should be
noted:
• We really mean the system has that
potential energy.
• Physically, only the change in potential
energy between two configurations has any
meaning.
• We are free to pick the “zero potential
energy” point anywhere we like by
arbitrarily assigning certain configuration to
have zero potential energy.
Consider a box with weight of 1 N hanging 10
m above the ground. We define zero
gravitational potential energy at y = 0:
(a) y (b) (c) y = 0
h/ 2
h y=0 h
h/ 2
y=0
h
Ug = mgh = 10 J Ug = mg = 5 J Ug = mg(0) = 0 J
2
The potential energy depends on the origin of
the coordinate system? Only the change in the
potential energy has physical meaning! Consider
the change in the potential energy if the box fell
to the ground:
∆Ug = U f − Ui
(a) ∆Ug = 0 − mgh = 0 − 10 J = −10 J
∆Ug = mg −  − mg  = −5 J − 5 J = −10 J

h h
(b)
 2  2
(c) ∆Ug = mg(− h) − 0 = −10 J
all the changes in the potential energy are
identical!
Elastic Potential Energy:

The spring force is a conservative force with
its associated elastic potential energy:
Ue = −W
= − ∫0x Fdx
= + ∫0x kxdx
= 21 kx 2
Mechanical Energy:
The mechanical energy of a system is the sum
of its potential energy and kinetic energy of the
objects:
E = K +U
Conservation of Mechanical Energy:

The total mechanical energy remains constant
for an isolated system of objects that interact
with conservative forces.
H Not only is the energy at the start of motion
equal to the energy at the end of motion, it
is equal at all times in between.
Example:
A 2 kg block slides down a frictionless
surface:
E 0 = K0 +U0
E3 =K3+U3
1m E1=K1+U1 E 4 =K4+U4
E 2 =K2+U2
E0 = E1 = E2 = E3 = E4
Position K.E. P.E. M.E.

0 0 20 20
1 12 8 20
2 20 0 20
3 10 10 20
4 15 5 20
• The kinetic energy and potential energy
change throughout the motion of the object,
i.e. not separately conserved.
• The total mechanical energy remains
constant, i.e. conserved.
Example:
A block slides down a frictionless ramp
from a height of h = 3 m. The initial velocity is 1
m/s. What is the velocity at the bottom and at
the top of the ramp?
y = h m v = 1 m/s
0
#0
#2
y = h_3
#1
y =0
• Since gravity is the only force performing
work on the object, the total mechanical
energy is conserved as gravity is a
conservative force.
(1) E0 = K0 + U0 = 12 mv02 + mgh
(2) = K1 + U1 = 12 mv12 + mg(0) = 12 mv12
= K2 + U2 = 12 mv22 + mg 
h
(3)
 3
(1),(2): 1
2 mv1
2
= 12 mv02 + mgh
v12 = v02 + 2gh
v1 = v02 + 2gh
= 7.7 m / s
• Answer looks like equation of motion, but
H v0 is in the vertical direction while v1 is in
the horizontal direction
H acceleration is not constant
equation of motion is not valid
• v1 is independent of mass, similar to the
projectile problem.
= 12 mv22 + mg 
1 2 h
(2),(3): 2 mv1
3
v22 = v12 − 23 gh
v2 = v12 − 23 gh
= 6.3 m / s
• Conservation of energy is a powerful tool:
solving impossible problem with ease!
If there is a non conservative force (e.g.
friction), then the total mechanical energy is not
conserved. The work done by the non
conservative force changes the mechanical
energy:
∆E = W nonconservative
So if we know the work done by a non
conservative force, we can determine how much
the mechanical energy changes.
Example:
A 1-kg block starts from rest 1 m up a
frictionless 30° ramp. On the horizontal surface
is a 0.5 m rough surface with a coefficient of
kinetic friction of 0.3. After the rough stretch, the
horizontal surface is again frictionless and there
is a spring with a spring constant 500 N/m.
How far is the spring compressed?
l = 1m
µ = 0.3 θ
d= 0.5 m
• To calculate the spring compression:
need to know the kinetic energy of the
block before impact
need to know the total mechanical
energy and the energy lost due to friction
Ei = mgl sinθ
W friction = − f k d
= − µNd
= − µmgd
= ∆E
= E f − Ei
E f = Ei − µmgd
= mglsin θ − µmgd
= mg(l sin θ − µd)
= Es
= 12 kx 2
2mg(lsin θ − µd)
x=
k
= 0.12 m
Conceptual Problem:
(1) Three blocks are launched with the same
initial speed at the same instant along the three
tracks of different elevations. Which will reach
the finish line first?
finish line
(2) I tell you that I have run an experiment in my

lab. I started a box from rest at point # 1. I tell
you that it slides down the ramp and up the
other side to point #2. Am I telling the truth?
#2
#1
Gravitational Potential Energy:

We define the gravitational potential energy:
Ug = mgh
This is valid only near the surface of the planet
(e.g. earth, moon) based on the assumption that
the gravitational force is constant. The more
general form for the force is:
GMp m
Fg =
r2
where Mp is the mass of the planet and m is the
mass of the object, and r is the distance between
the two objects. The work done in moving the
object from infinity to r yields a change in the
potential energy:
r r
Ug = − ∫∞r Fg ⋅ dr
= ∫∞r Fg dr
GM p m
= r
∫∞ 2 dr
r
r
 GM p 
m
=−
 r  ∞
GM p m
Ug = −
r
• Zero potential energy corresponds to when
the distance between the objects is infinite.
Escape Velocity:
The speed that an object must have to escape
the gravitational attraction of a planet. The
speed can be calculated using conservation of
energy:
At the surface of the planet:
Ei = 12 mv 2 + Ug
GM p m
= 1
2 mv 2
−
r
As the object moves away from the planet,
the potential energy increase and the speed
decrease: at infinity, both the potential energy
and speed are zero:
Ef = 0
From conservation of energy:
GM p m
Ei = E f = 2 mv −
1 2
=0
r
1 2 =
GM p
2v
r
2GM p
vescape =
r
• 11.2 km/s for the planet earth.

Potential Energy and Conservation of Energy Potential Energy

Uploaded by

Copyright:

Available Formats

Potential Energy and Conservation of Energy Potential Energy

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Potential Energy and Conservation of Energy Potential Energy

Uploaded by

Copyright:

Available Formats

8.

Potential Energy and Conservation

Properties of Conservative Force:

• In principle, we can calculate the work done

W = W(horizontal path) + W(vertical path)

Potential Energy Calculation:

Gravitational Potential Energy:

∆Ug = mg −  − mg  = −5 J − 5 J = −10 J

Elastic Potential Energy:

Conservation of Mechanical Energy:

Position K.E. P.E. M.E.

(2) I tell you that I have run an experiment in my

Gravitational Potential Energy:

You might also like