Experiment 7: Reading
Experiment 7: Reading
Experiment 7: Reading
Experiment 7
Simple Harmonic Motion
Reading:
Bauer&Westfall Chapter 13 as needed (e.g. definitions of oscillation variables)
Homework 10: turn in the first week of this experiment. (No homework 11!)
1. Define and explain briefly the meaning of the terms (a) restoring force, (b) free
oscillation, (c) simple harmonic motion, (d) phase angle and (e) natural frequency.
Using Figure 2 in the write-up below,
2. What is the amplitude of the oscillation at t = 10 sec? at t = 0 sec?
3. Determine the period T, the angular frequency ω and the phase angle ϕ in cos(ω t + ϕ).
4. Redraw the oscillations in Fig. 2 for phase angle ϕ = π/2.
Extra Credit:
5. Show by using Hooke’s Law that a stationary mass m hanging from a spring with
mg
constant k (Fig. 1) stretches the spring to a new equilibrium position x0 = .
k
6. Confirm by substitution that Eq. (7) indeed solves Eq. (6).
7. Show that when β= 0 (no damping), Eq. (7) reduces to Eq. (3).
1. Goals
1. Understand the properties of an oscillating system governed by Hooke’s Law.
2. Study the effects of friction on an oscillating system, which leads to damping.
3. Use a non-linear least-squares fitting procedure to characterize an oscillator.
4. Learn the basics of using an oscilloscope.
5. Understand how to detect a power law relationship between variables.
2. Theoretical Introduction
2.1 Simple Harmonic Oscillation (SHO) Consider a system illustrated in the figure below. It
consists of a mass m suspended from a spring with spring constant k.
Hooke’s law states that the force resisting the extension of the spring is proportional to the
deviation of the spring from its equilibrium position. That is, F = - k x, where x = 0 is defined by
the equilibrium position of the spring. If we gently add a mass to the spring, the spring will
PHY191 Experiment 7: Simple Harmonic Motion 7/30/2008 Page 2
stretch to a new (lower) equilibrium position, -xo = - mg/k, where g is the gravitational constant.
At this position, the vertical restoring force of the spring balances the weight. In what follows,
we will take the origin of x at this new equilibrium position. In these final coordinates, at x=0
the gravitational force is canceled by the force due the spring, so that we can ignore the constant
gravitational force in this coordinate system, and consider only additional Hooke’s law forces
beyond those required to cancel the weight.
If the mass is now displaced from its equilibrium position, the same equation F = - kx still
applies, where x is now that displacement. In other words, when such a displacement is made, a
restoring force again acts to return the mass to its equilibrium position. Upon release, the mass
moves toward the equilibrium position, but its inertia causes it to “overshoot” this point. The
motion then continues through the equilibrium position and beyond until the restoring force
eventually stops the mass and pulls it back toward the equilibrium position. The motion then
repeats itself back and forth through the position of equilibrium. Newton’s second law states that
any unbalanced force results in an acceleration of the mass, proportional to the force. If we apply
Newton’s second law to the motion of a mass m that is subject to Hooke’s law, we get
d 2x
m 2 = − kx, (1)
dt
which can be written as
d 2x k
2
+ ω 02 x = 0, where ω 02 = (2)
dt m
We have studied the solution of this equation in Experiment 3. The simple pendulum underwent
simple harmonic oscillation with angular frequency ω = g / L , where g is the gravitational
constant and L is the effective length. We found that the solution for the simple pendulum was
expressed in a sinusoidal form, Θ(t) = Θo sin(ω t). Therefore, we anticipate that the solution for
Eq. (2) should be similar. However, we can’t guarantee synchronization of the phase with
passage through equilibrium, so leave it as a free parameter:
x(t ) = A cos(ω 0 t + ϕ ), (3)
where A is the amplitude of oscillation, ϕ is a phase constant, and ω 0 is the angular frequency:
k
ω0 = . (4)
m
2.2 Damped Harmonic Oscillation (DHO) The amplitude of oscillation of the mass
gradually decreases over time. This is due to the effect of friction or a drag (resistive) force. We
want to see if we can understand its effects. For our example, the effect of friction can be
represented as a force proportional to the velocity of the mass. Therefore, Eq. (1) can be modified
to read
d 2x dx
m 2 = −kx − β (5)
dt dt
where β is a constant of proportionality, called the damping coefficient. The minus sign indicates
that the damping force is always opposite to the direction of motion. Rearranging the above
equation yields
PHY191 Experiment 7: Simple Harmonic Motion 7/30/2008 Page 3
d 2x dx
2
+ 2γ + ω 02 x = 0 , (6)
dt dt
β
where γ = . The solution to this (second order differential) equation is no longer SHO. If
2m
β is not too large, it is a modification of SHO. Also, the frequency of oscillation will be modified
by the damping. The solution may be made plausible by an educated guess. We postulate that the
oscillatory motion is still sinusoidal, but that the amplitude of oscillatory motion decreases as a
function of time. So our trial solution is
x (t ) = A e −γ t cos(ω t + ϕ ), (7)
where A is the amplitude, ϕ is the phase angle, and it turns out that ω = ω 02 − γ 2 is the angular
frequency of this system. See Appendix A for a more complete derivation. The coordinate x (t ) ,
as a function of time t, is shown in Fig. 2.
Fig. 2. Damped harmonic oscillator displacement as a function of time. The envelope decay
function is exp(-γt). The period T is related to ω by T = 2 π / ω , where ω = 2 π f.
Experimental Procedure
3.1 The Dynamic Force Transducer In this experiment we will use a Dynamic Force
Transducer (DFT), an electronic device that outputs a voltage proportional to a force applied to
it. In Parts 7 and 8, we will hook the outputs of the DFT to the input terminal block of a
LabView card and use LabView to monitor the applied force. If we use the DFT as the spring
support, then the force exerted by the spring is measured. If we ignore the mass of the spring (a
constant), this force is the same as that applied to the hanging mass and is by Hooke’s Law
proportional to the displacement of the mass from equilibrium. Thus, by monitoring the force in
the spring we are, in effect, monitoring the position of the mass. The transducer produces a
voltage proportional to force, with a scale controlled by the “sensitivity” knob, so the scale is
unknown unless we calibrate it. Further, we may use the “zero adjust” knob to zero the force
readout for some one mass, but we use several different masses, and the zeroing may be inexact.
PHY191 Experiment 7: Simple Harmonic Motion 7/30/2008 Page 4
Thus, we may regard the DFT readout as giving not x, but B x + C, and we should add an
arbitrary constant to any Kgraph equations used to fit DFT output.
3.2 Inertial Mass. Throughout the lab, whenever measuring mass, be sure to include the
support hook as well. (We will ignore the mass of the spring.). The mass in Eq. (1) is the
whole mass that is accelerating—the inertial mass of F=ma. That of course is the same mass as
enters in Eq 4 for the angular frequency.
4. Checking DFT output vs. position. There are two knobs on the DFT, zero adjust (or
“offset”) and sensitivity (of “gain”). Set the sensitivity knob nearly fully clockwise and do not
touch it again during the experiment. Measure the hook mass, then attach the spring and hook to
the DFT. The output of the DFT goes to the digital oscilloscope (described Appendix B: read
before class!). With the spring and hook mass at equilibrium, set up the scope as described in the
appendix, and then adjust the offset of the DFT until the output reads zero volt(s) on the digital
scope display. Note that zeroing the output at equilibrium is for convenience only, but the
resulting voltage is your measurement for the hook alone, with no mass added.
1. Measure the output (volts) for three more masses. The recommended order is 100g, 150g,
and 200g (total of hook + added mass). Assuming Hooke’s law to be true (and the DFT
to behave as advertised), write down the general equation relating output to the mass.
2. For these four measurements make a graph of V (volts) vs. m (grams). What function
describes the dependence of V on m? Is it roughly consistent with what you predicted?
Do you think the DFT will do a good job of measuring position?
5. Static Measurement of the Force Constant. In this part you check Hooke’s Law by
measuring the displacement vs. mass using a metric ruler.
1. Measure displacements for three (3) different masses. Assign uncertainties to the
measured displacements; you can ignore the uncertainty of the masses. Don’t forget to
include the mass of the hook.
2. Plot displacements (in units of cm) vs. mass (in units of grams) using K-graph.
3. Apply a least-squares fit procedure to obtain the spring constant k and its uncertainty.
Hint: What are the units of k? of the slope?
4. Predict the oscillation frequency ωo for each of these masses. Show the calculation in
your notebook.
6. Measurement of the Period of SHO. In this part of the experiment you will use the
oscilloscope T cursors to measure (for 4 masse values) the angular frequency of oscillation ωo.
1. Attach your first mass to the spring and set it into oscillation. Pick an appropriate point of
reference and measure the time for several complete cycles of the oscillation. Record the
time in your notebook. What’s more accurate: a single cycle, or several? Why?
2. Repeat step 1 for your second and third mass you used in Part 5.
3. To obtain ωo, note that ωo = 2πf, where f is measured in cycles per second.
4. Compare these ωo with those you predicted in Part 5.
5. Now do one more mass value you haven’t done before.
5. Using K-graph, plot your data of ωo vs. m. Now, using the RG note on Log Plots, make
another plot with one or more axes logarithmic, which tests whether you observe the
functional dependence predicted by Eq. (4). Hint: what shape, and what slope, would you
observe if Eq.(4) were true?
PHY191 Experiment 7: Simple Harmonic Motion 7/30/2008 Page 5
1. Attach the spring-hook-mass (150g total) combination to the DFT. With the help of the
digital scope, adjust the DFT offset so the signal is symmetric about 0V. Set the spring-
mass system into oscillation, observe the pattern on the scope display and sketch it in
your notebook.
2. The output of the DFT is also connected to a data acquisition card on the PC. Open
R:\exp7_ref\ ForceTransducer.vi. The following specifications are needed in order to
collect the data successfully. Set device = 1; channels = 0; scan numbers = 1000, scan
rate = 100. The scan numbers is just the number of data points; the scan rate is the
number of points/second, so the number of seconds for which you will record data is just
scan numbers/ scan rate. If you need a longer data sample, raise the scan numbers; if
you need finer sampling, raise the scan rate. Note: if you are using a flash drive, be
careful to NOT remove the USB DAQ device along with your flash drive.
Set the spring-mass system into oscillation and click the arrow button or press Ctrl R to
begin collecting the data. (The scanning process will take 10 seconds.) When it is done,
the program will ask you to save the data on the U drive. Caution: When exiting the
program, it will ask you if you want to save the current setting. Choose NO.
3. Use K-graph to retrieve the data file. Use “Any files *.*”, not “All Files”; don’t ask me
why, but they aren’t equivalent. When inputting your data to Kgraph, the following
specifications are required: Delimiter = Tab; Number = 1, Line Skipped = 0,
Options/Read Title (No check). Your file contains two columns: the first column is the
time, the second column is the output voltage. The data is big: don’t print data tables.
4. Plot voltage vs. time and use the general curve-fit editor to perform a non-linear least
squares fit procedure using the function given in Eq. (3). The corresponding Kgraph
function is m1+m2*cos(m3*x + m4); m3 and m4 are in radians (m1 is the unknown
voltage for x=0). Explain why you need the m1 parameter, since it’s not in Eq (3).
Notes:
• This non-linear least-squares fit function will not converge unless your initial
parameters (m1… m4) are realistic—especially for the angular frequency, for which
you must find a way to get a good estimate. Show in your notebook how you
estimated each parameter. How do the values compare to those output by K-graph?
• The fit is subject to the ambiguities inherent in trig functions. The parameters of the
fit should be reduced to standard form using trig identities. You should wind up with
a positive amplitude, a positive ω, and a phase angle in the range [-π, π]. A simple
procedure is to first correct the sign of the amplitude (if necessary) by –cos(z) =
cos(z+π), then correct the sign of ω if necessary by cos(-z) = cos(z), and finally correct
ϕ by cos(z) = cos(z ± 2Nπ), where N is any integer. Show the steps in your notebook,
and report the final values in your report or hand-written on your plot (which should
show the original fit values and uncertainties)
PHY191 Experiment 7: Simple Harmonic Motion 7/30/2008 Page 6
6. Summarize your measurements in two tables, one for angular frequencies ω and ωo, and
another (shorter) for estimates of γ. The ω table should include the method, mass, value,
prediction, and difference in %; base the predictions on the results from Part 5.
The solution Eq. (7) for the damped harmonic oscillator in Eq. (6) can be found as follows.
d 2x dx
2
+ 2γ + ω 02 x = 0 . (A1)
dt dt
The general solution is
x(t ) = Ae Q t , (A2)
where Q is a factor to be determined. Then
d d2
x (t ) = QAe Qt = Q ⋅ x(t ) and x(t ) = Q 2 Ae Qt = Q 2 ⋅ x (t )
dt dt 2
Substitution of these two in (A1) yields
(Q 2 + 2γ Q + ω 02 ) x(t ) = 0 , (A3)
which has a solution of the form
− 2γ + 4γ 2 − 4ω 02
Q= = −γ + γ 2 − ω 02 . (A4)
2
For our case, which involves a weakly damped oscillation, ω 0 >> γ . Therefore, our solution
(A4) becomes
Q = −γ +i ω 02 − γ 2 = −γ +iω with ω = ω 02 − γ 2 and ω 02 = k / m (A5)
Our general solution Eq. (A2) now becomes
A −γ t i (ω t +ϕ ) A −γ t −i (ω t +ϕ ) 1
x(t ) = e e + e e = Ae −γ t (e i (ω t +ϕ ) + e −i (ω t +ϕ ) ). (A7)
2 2 2
e iθ + e −iθ
But cos(θ ) = . Thus,
2
1 i (ω t +ϕ )
x(t ) = Ae −γ t (e + e −i (ω t +ϕ ) ) = Ae −γ t cos(ω t + ϕ ), (A8)
2
Connect a BNC cable from the transducer to the channel A input. Turn on the scope. Press
"AC/DC" button until the digital display shows "DC". ("DC" shows the real voltage; "AC" only
shows variations about the average). Also, turn the “DIGITAL MEMORY” on. Choose the time
base (the value of the 1 cm grid of the time scale) with the "TB s µs" switch to be equal to "0.5
s", and the voltage scale with the “A V – mV” switch to be equal to "0.1 V". During the lab, you
may want to adjust these settings to get the best presentation of the graph. It’s also nice to push
XMAGN 6 times or so until the display shows [---------] instead of [---- ] so the scope
continuously collects new data. The TB will now be 1.0s; re-adjust it to .4s .
Press "GND". This, connects the scope input will be to “ground” (= 0V). Turn the Y-pos and X-
pos knobs to position the green line of the signal exactly in the middle of the screen. Do not
touch the X- pos and Y-pos buttons for the rest of your measurements. This ensures the correct
calibration of the picture offsets inside the scope. Then you will only need to worry about the
voltage offset inside the force transducer, which you adjust with "ZERO" knob of the transducer.
Press "GND" again. Now you will see the signal coming from the transducer. For nonzero mass,
it will be vertically shifted with respect to the center of the screen. For static stretching of the
spring, you will measure this displacement of the signal to find the dependence between the
applied mass, elongation of the string and the voltage. During the study of oscillations, you will
have to adjust the "ZERO" on the force transducer until the signal line is again in the middle.
Thus you will make sure that the voltage shown corresponds to the displacement of the mass
from the equilibrium point, and not from some other location of the system.
Several other useful buttons: you may use the knobs to the left of the screen to adjust the focus
and the brightness of the line. The button “LOCK” will allow you to lock (freeze) the image,
which makes detailed measurements on the captured image convenient, as described below.
PHY191 Experiment 7: Simple Harmonic Motion 7/30/2008 Page 9
Inspect the main screen. If there is no writing at the bottom of the screen, press one of the blue
"soft-keys below the screen to make the writing appear. If there is some writing and one of the
soft-keys has RETURN written above it, keep pressing it until it no longer says RETURN, to get
back to the top menu. You should see:
Reading Voltages. We will use these soft-keys to move screen cursors so they correspond to the
size of our signal and read off voltages from the screen. Press the CURSORS soft-key. Press
MODE to set up the cursors we want. Toggle the V-CURS and T-CURS soft-keys until the
horizontal cursor lines are on and the vertical cursor lines are off. Press RETURN.
Press V-CTL to control the Voltage, cursors. The V cursors measure voltage, which is displayed
as the vertical (y) axis on the screen. They appear as horizontal lines on the screen, representing
a constant voltage level. Move the top one down to the level of your signal, and move the
bottom one up to the reference value. The REF line must be lower than the ∆ line, so if you are
measuring a negative voltage, you’ll have to add the sign. The value is displayed at the top of
the screen. For uncertainty estimation: use 2 clicks, or two line widths, or re-measure a few
times.
Frequency Measurement: Next, we wish to determine the time between 2 points. Time is
measured as a horizontal distance on the screen. The sine-wave signal is cyclic: it repeats itself.
The time a sine-wave signal takes to make one cycle is called the period of the signal. It has
units of seconds. The inverse of the period is the frequency (in Hz).
To measure time we need the T-cursors (T stands for time). Time is displayed as the x-axis on
the screen, so a constant time is marked by the T cursor as a vertical line. Return to the top-level
menu using the RETURN soft-key. Press MODE and toggle the T-CURSOR to on. Hit
RETURN, then hit T-CTL to move the time-cursors to the left and right. The length of the cycle
can be measured by positioning the T-cursors on equivalent points on the trace, for example, on
two adjacent peaks or two adjacent valleys. The period and the frequency can both be read off
from the top of the screen, but the frequency is “calculated” rather coarsely, so measure the
period and calculate the frequency yourself by f = 1/T !
PHY191 Experiment 7: Simple Harmonic Motion 7/30/2008 Page 10
Soft Keys
BNC Cable
LCD Screen