Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
411 views

Liquid Level Sensor UserManual PDF

This document provides a user manual for a liquid level sensor module. It describes the module's features such as an analog output, detectable depth of 48mm, and operating voltage range of 2.0-5.0V. The module works by using a transistor to amplify current based on liquid conductivity between contacts. It can be used to build a liquid level alarm system by connecting it to a development board and reading the analog voltage output. Instructions are provided on interfacing the module with an STM32 or Arduino board to obtain liquid level readings.

Uploaded by

Rodrigo Ortolá Inocenti
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
411 views

Liquid Level Sensor UserManual PDF

This document provides a user manual for a liquid level sensor module. It describes the module's features such as an analog output, detectable depth of 48mm, and operating voltage range of 2.0-5.0V. The module works by using a transistor to amplify current based on liquid conductivity between contacts. It can be used to build a liquid level alarm system by connecting it to a development board and reading the analog voltage output. Instructions are provided on interfacing the module with an STM32 or Arduino board to obtain liquid level readings.

Uploaded by

Rodrigo Ortolá Inocenti
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Liquid Level Sensor User Manual Waveshare

Liquid Level Sensor User Manual


1. Features
Operating voltage 2.0V-5.0V
Output type Analog output
Detectable depth 48mm
Dimensions 19.0mm*63.0mm
Fixing hole size 2.0mm
Operating principle:
This module is an application of the current amplification by a transistor.
When the liquid level is high enough to conduct the current between the
base and the positive power supply, a certain amount of current is
generated between the base and the emitter. And in a mean while, an
electric current is produced in a certain amplification factor between the
collector and the emitter, and applied to the resistant in the emitter to
produce a voltage. Then, this voltage will be collected by an AD converter.
2. Applications
This module can be applied to liquid level alarm system.
3. Interfaces
Pin No. Symbol Descriptions
1 AOUT Analog output
2 GND Power ground
Positive power
3 VCC
supply (3.3V-5.0V)

4. How to use
We will illustrate the usage of the module with an example of liquid level
detection by connecting a development board.
① Download the relative codes to the development board.
② Connect the development board to a PC via a serial wire and the
module to the development board. Then, power up the development
board and start the serial debugging software.
Here is the configuration of the connection between the module and the
development board.

Port STM32 MUC pin


AOUT GPIOA.6
GND GND
VCC 3.3V

1
Liquid Level Sensor User Manual Waveshare

2
Liquid Level Sensor User Manual Waveshare

Port Arduino pin


AOUT A0
GND GND
VCC 5V

Here is the configuration of the serial port.


Baud rate 115200
Data bits 8
Stop bit 1
Parity bit None

③ Put the module into the water, and the serial output is as followed:
Output on high level Output on low level
High water level! High water level!

④ Immerse the sensor into the water deeply. The table below shows the
relationship between the output voltage from the AOUT pin and the
liquid level.
Liquid level Output
voltage
0cm 0v
0.5cm 1.3v
1cm 1.53v
1.5cm 1.62v
2cm 1.69v
2.5cm 1.74v
3cm 1.77v
3.5cm 1.81v
4cm 1.84v
4.5cm 1.86v
4.8cm 1.88v

You might also like