Product Description: T400Hw02 TFT-LCD Panel With Rohs Guarantee

Global LCD Panel Exchange Center www.panelook.
com
Product Description: T400HW02 TFT-LCD PANEL with RoHS guarantee
AUO Model Name: T400HW02 V3
Customer Part No/Project Name:
Customer Signature Date AUO Date
Approved By: PM Director / Frank Hsu
--------------------------------------------
Reviewed By: RD Director / Hong Jye Hong
--------------------------------------------
Reviewed By: Project Leader /Tzuchieh Lai
--------------------------------------------
Prepared By: PM /Cynthia Hung
---------------------------------------------
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Document Version: 0.0

Date:2008/09/30
Product Specifications
40” Full HD Color TFT-LCD Module

Model Name: T400HW02 V3
(*) Preliminary Specifications

() Final Specifications
Contents
No
CONTENTS
RECORD OF REVISIONS
1 GENERAL DESCRIPTION
2 ABSOLUTE MAXIMUM RATINGS
3 ELECTRICAL SPECIFICATION
3-1 ELECTRIACL CHARACTERISTICS
3-2 INTERFACE CONNECTIONS
3-3 SIGNAL TIMING SPECIFICATION
3-4 SIGNAL TIMING WAVEFORM
3-5 COLOR INPUT DATA REFERENCE
3-6 POWER SEQUENCE
3-7 BACKLIGHT CONNECTOR PIN CONFIGURATION
4 OPTICAL SPECIFICATION
5 MECHANICAL CHARACTERISTICS
6 RELIABILITY TEST ITEMS
7 INTERNATIONAL STANDARD
7-1 Safety
7-2 EMC
8 PACKING
9 PRECAUTION
Record of Revision
Version Data No Old Description New Decription Remark
0.0 2008/09/30 First release N/A
1. General Description
This specification applies to the 40.0 inch Color TFT-LCD Module T400HW02 V3. This LCD
module has a TFT active matrix type liquid crystal panel 1,920x1,080 pixels, and diagonal size of 40.0
inch. This module supports 1,920x1,080 mode. Each pixel is divided into Red, Green and Blue
sub-pixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel
color is determined with a 8-bit gray scale signal for each dot.
The T400HW02 V3 has been designed to apply the 8-bit 2 channel LVDS interface method. It is
intended to support displays where high brightness, wide viewing angle, high color saturation, and
high color depth are very important.
* General Information
Items Specification Unit Note

Active Screen Size 40.00 inch
Display Area 885.6(H) x 498.15(V) mm
Outline Dimension 952.0(H) x 551.0 (V) x 48.4(D) mm With socket cover
Driver Element a-Si TFT active matrix
Display Colors 8 bit, 16.7M Colors
Number of Pixels 1,920x1,080 Pixel
Pixel Pitch 0.46125 (H) x 0.46125(W) mm
Pixel Arrangement RGB vertical stripe
Display Operation Mode Normally Black
Surface Treatment Anti-Glare, 3H Haze=11%
2. Absolute Maximum Ratings

The followings are maximum values which, if exceeded, may cause faulty operation or damage to the
unit
Item Symbol Min Max Unit Condition

s
Logic/LCD Drive Voltage Vcc -0.3 14 [Volt] Note 1
Input Voltage of Signal Vin -0.3 3.6 [Volt] Note 1
o
Operating Temperature TOP 0 +50 [ C] Note 2
Operating Humidity HOP 10 90 [%RH] Note 2
o
Storage Temperature TST -20 +60 [ C] Note 2
Storage Humidity HST 10 90 [%RH] Note 2
Panel Surface Temperature PST 65 [ oC] Note 3
Note 1: Duration:50 msec.

Note 2 : Maximum Wet-Bulb should be 39 and No condensation.
The relative humidity must not exceed 90% non-condensing at temperatures of 40 or less. At
temperatures greater than 40 , the wet bulb temperature must not exceed 39 .
Note 3: Surface temperature is measured at 50 Dry condition
3. Electrical Specification
The T400HW02 V3 requires two power inputs. One is employed to power the LCD electronics and to
drive the TFT array and liquid crystal. The second input, which powers the CCFL, is typically
generated by an integrate power (I/P) system.
3.1 Electrical Characteristics

Value
Parameter Symbol Unit Note
Min. Typ. Max
LCD
Power Supply Input Voltage V DD 10.8 12 13.2 V DC 1
Power Supply Input Current I DD -- 1.14 1.25 A 2
Power Consumption PC -- 13.68 15.0 Watt 2
Inrush Current I RUSH -- -- 4.5 A 3
Differential Input High Threshold
VTH -- -- +100 mVDC 4
Voltage
LVDS Differential Input Low Threshold
VTL -100 -- -- mVDC 4
Interface Voltage
Input Common Mode Voltage V ICM 0.6 1.2 1.8 V DC 4
VIH
Input High Threshold Voltage 2.4 -- 3.3 VDC
CMOS (High)
Interface VIL
Input Low Threshold Voltage 0 -- 0.7 VDC
(Low)
Life Time 50000 -- Hours
Note :
1. The ripple voltage should be controlled under 10% of V CC
2. Vcc=12.0V, f v = 60Hz, fCLK=81.5Mhz , 25, Test Pattern : White Pattern
3. Measurement condition :
Vdd
0.9 Vdd
0.1 Vdd
GND
400μs
4. VCIM = 1.2V
VTH
VCIM
VTL
0V
5. The performance of the Lamp in LCD panel, for example life time or brightness, is extremely
influenced by the characteristics of balanced board and I/P board. All the parameters should
be carefully designed as not to produce too much leakage current from high-voltage output.
While you design or order the balance board, please make sure unwanted lighting caused by
the mismatch of the lamp and the balanced board (no lighting, flicker, etc) never occurs. After
confirmation, the LCD panel should be operated in the same condition as installed in your
instrument
6. Do not attach a conducting tape to lamp connecting wire. If the lamp wire attach to conducting
tape, TFT-LCD Module have a low luminance and the inverter has abnormal action because
leakage current occurs between lamp wire and conducting tape.
7. The relative humidity must not exceed 80% non-condensing at temperatures of 40 or less.
At temperatures greater than 40, the wet bulb temperature must not exceed 39 . When
operate at low temperatures, the brightness of CCFL will drop and the life time of CCFL will be
reduced.
3.2 Interface Connections

LCD connector: FI-RE51S-HF (JAE)
Mating connector: FI-RE51S-HL (JAE)
PIN # Signal Name Description

1 VDD 12V power supply
6 GND Ground
7 GND Ground
8 GND Ground
9 GND Ground
10 RO_0- Negative(-) LVDS differential data input
11 RO_0+ Positive(+) LVDS differential data input
16 GND Ground
17 RO_CLK- Clock Signal(-)
18 RO_CLK+ Clock Signal(+)

19 GND Ground

22 NC No connection
23 NC No connection
24 GND Ground
25 RE_0- Negative(-) LVDS differential data input
26 RE_0+ Positive(+) LVDS differential data input

31 GND Ground
32 RE_CLK- Clock Signal(-)
33 RE_CLK+ Clock Signal(+)
34 GND Ground

37 NC No connection
38 NC No connection
39 GND Ground
40 SCL EEPROM Serial Clock
41 Reserved Please leave it open

45 LVDS Select LVDS data order (NS: High/Open, JEIDA: Low)
LVDS Option = High/OpenNS
Previous Cycle Current Cycle Next Cycle
Clock
RIN0+
R1 R0 G0 R5 R4 R3 R2 R1 R0 G0
RIN0-
RIN1+
G2 G1 B1 B0 G5 G4 G3 G2 G1 B1
RIN1-
RIN2+
B3 B2 DE NA NA B5 B4 B4 B2 DE
RIN2-
RIN3+
R7 R6 NA B7 B6 G7 G6 R7 R6 NA
RIN3-
LVDS Option = LowJEIDA
Previous Cycle Current Cycle Next Cycle
Clock
RIN0+
R3 R2 G2 R7 R6 R5 R4 R3 R2 G2
RIN0-
RIN1+ G4 G3 B3 B2 G6 G6 G5 G4 G3 B3
RIN1- G7
RIN2+
B5 B4 DE NA NA B7 B6 B5 B4 DE
RIN2-
RIN3+
R1 R0 NA B1 B0 G1 G0 R1 R0 NA
RIN3-
3.3 Signal Timing Specification

This is the signal timing required at the input of the user connector. All of the interface signal timing
should be satisfied with the following specifications for its proper operation.
Timing Table (DE only Mode)

For 60Hz
Signal Item Symbol Min. Typ. Max Unit
Period TV 1090 1125 1480 TH

Vertical Section Active TDISP (V) 1080 TH
Blanking T BLK (V) 10 45 400 TH
Period TH 1030 1100 1300 TCLK
Horizontal Section Active TDISP (H) 960 TCLK
Blanking T BLK (H) 70 140 340 T CLK
Clock Frequency 1/T CLK 50 74.25 82 MHz
Vertical Frequency Frequency FV 47 60 63 Hz
Horizontal Frequency Frequency FH 60 67.5 73 KHz
Notes:
1.) Display position is specific by the rise of DE signal only.
st st
Horizontal display position is specified by the rising edge of 1 DCLK after the rise of 1 DE, is
displayed on the left edge of the screen.
Vertical display position is specified by the rise of DE after a “Low” level period equivalent to eight
times of horizontal period. The 1 st data corresponding to one horizontal line after the rise the of 1 st DE
is displayed at the top line of screen.
3.) If a period of DE “High” is less than 1366 DCLK or less than 768 lines, the rest of the screen
displays black.
4.) The display position does not fit to the screen if a period of DE “High” and the effective data period
do not synchronize with each other.
3.4 Signal Timing Waveforms
3.5 Color Input Data Reference

The brightness of each primary color (red, green and blue) is based on the 8 bit gray scale data input for
the color; the higher the binary input, the brighter the color. The table below provides a reference for color
versus data input.
COLOR DATA REFERENCE
Input Color Data

RED GREEN BLUE
Color
MSB LSB MSB LSB MSB LSB
R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
Basic Blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Color Cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
RED(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED(001) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED ----
RED(254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
GREEN(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
GREEN(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0
GREEN ----
GREEN(254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0
GREEN(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
BLUE(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
BLUE(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
BLUE -------
BLUE(254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0
BLUE(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
3.6 Power Sequence
Values
Parameter Unit
Min. Typ. Max.
t1 0.4 -- 30 ms
t2 0.1 -- 50 ms
t3 300 -- -- ms
t4 10 -- -- ms
t5 0.1 -- 50 ms
t6 -- -- 300 ms
t7 500 -- -- ms
Note:
The timing controller will not be damaged in case of TV set AC input power suddenly shut down.
Once power reset, it should follow power sequence as spec. definition.
(1) Apply the lamp voltage within the LCD operation range. When the back-light turns on before the LCD
operation or the LCD turns off before the back-light turns off, the display may momentarily become
abnormal screen.
3.7 Backlight Connector Pin Configuration
Note 1
Note 2
Note 3
Input Interface for LIPS board

CN1 :EL7H001ZZ2 (JAE)
4. Optical Specification
Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 45 minutes
in a dark environment at 25 °C. The values specified are at an approximate distance 50cm from the LCD
surface at a viewing angle of φ and θ equal to 0°.
Fig.1 presents additional information concerning the measurement equipment and method.
SR3 or equivalent
Values
Parameter Symbol Unit Notes
Min. Typ. Max
Contrast Ratio CR 4000 5000 -- 1

2
Surface Luminance (White) L WH 400 500 -- cd/m 2
Luminance Variation δWHITE(9P) -- -- 1.3 3
Response Time (G to G) Tγ -- 8 -- Ms 4
Color Gamut NTSC 72 %
Color Coordinates
Red RX 0.637
RY 0.336
Green GX 0.277
GY 0.590
Typ.-0.03 Typ.+0.03
Blue BX 0.145
BY 0.057
White WX 0.280
WY 0.290
Viewing Angle 5
x axis, right(φ=0°) θr -- 89 -- degree
x axis, left(φ=180°) θl -- 89 -- degree
y axis, up(φ=90°) θu -- 89 -- degree
y axis, down (φ=270°) θd -- 89 -- degree
Note:
1. Contrast Ratio (CR) is defined mathematically as:
Surface Luminance of Lon5
Contrast Ratio=
Surface Luminance of Loff5
2. Surface luminance is luminance value at point 5 across the LCD surface 50cm from the surface with all
pixels displaying white. From more information see FIG 2. When lamp current I H = 11mA. LWH=Lon5
where Lon5 is the luminance with all pixels displaying white at center 5 location.
3. The variation in surface luminance, δWHITE is defined (center of Screen) as:

δWHITE(9P)= Maximum(L on1, Lon2,…,Lon9)/ Minimum(L on1, Lon2,…Lon9)
4. Response time Tγ is the average time required for display transition by switching the input signal for
five luminance ratio (0%,25%,50%,75%,100% brightness matrix) and is based on f v=60Hz to optimize.
5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for
the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD
surface. For more information see FIG4.
FIG. 2 Luminance
H/2 1 2 3
4 5 6 H
7 8
H/6
V/6 V/2
FIG.3 Response Time
The response time is defined as the following figure and shall be measured by switching the input signal for
“any level of gray(bright) “ and “any level of gray(dark)”.
Any level of gray(Bright) Any level of gray(Dark) Any level of gray(Bright)
L0,15,L31,.L255 L0,15,L31,.L255
Photodetector
Output
L0,15,L31,.L255
Time
TrR
FIG.4 Viewing angle
5. Mechanical Characteristics
The contents provide general mechanical characteristics for the model T400HW02 V3. In addition the
figures in the next page are detailed mechanical drawing of the LCD.
Horizontal 952.0 mm
Vertical 551.0 mm
Outline Dimension
Depth 48.4 mm(to socket cover)
Horizontal 891.7 mm
Bezel Opening
Vertical 504.2 mm
Horizontal 885.6mm
Active Display Area
Vertical 498.15 mm
Weight 10500g (Typ.)
Surface Treatment Anti-Glare, 3H
Front view
Rear view
6. Reliability Test Items
Test Item Q’ty Condition

1 High temperature storage test 3 60, 300hrs
2 Low temperature storage test 3 -20 , 300hrs
3 High temperature operation test 3 50 , 300hrs
4 Low temperature operation test 3 -5 , 300hrs

(10~300Hz/1.5G/11min SR, XYZ 30,im/axis)
Vibration level : 1.5G RMS, Bandwidth:
5 Vibration test (non-operation) 3
10-300Hz,
Duration: X, Y, Z 30min
Shock level: 50G
6 Shock test (non-operation) 3 Waveform: half since wave, 11ms
Direction: ±X, ±Y, ±Z, One time each direction
Random wave (1.5G RMS, 10-200Hz)

7 Vibration test (With carton) 3
30mins/ Per each X,Y,Z axes
Height: 38.1cm
8 Drop test (With carton) 3 1 corner, 3 edges, 6 surfaces
(ASTMD4169-I)
7. International Standard
7.1 Safety
(1) UL1950 Third Edition, Underwriters Laboratories, Inc. Jan. 28, 1995
Standard for Safety of Information Technology Equipment Including electrical
Business Equipment.
(2) CAN/CSA C22.2 No. 950-95/60950 Third Edition, Canadian Standards Association,
Standard for Safety of Information Technology Equipment Including Electrical
Business Equipment.
(3) EN60950: 1992+A2: 1993+A2: 1993+C3: 1995+A4: 1997+A11: 1997
IEC 950: 1991+A1: 1992+A2: 1993+C3: 1995+A4:1996
European Committee for Electrotechnical Standardization (CENELEC)
EUROPEAN STANDARD for Safety of Information Technology Equipment Including
Electrical Business Equipment.
7.2 EMC
a) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage
Electrical and Electrical Equipment in the Range of 9kHz to 40GHz. “American
National standards Institute(ANSI), 1992
b) C.I.S.P.R “Limits and Methods of Measurement of Radio Interface Characteristics of
Information Technology Equipment. ” International Special committee on Radio
Interference.
c) EN 55022 “Limits and Methods of Measurement of Radio Interface Characteristics of
Information Technology Equipment. ” European Committee for Electrotechnical
Standardization. (CENELEC), 1998
8. Packing
8-1 DEFINITION OF LABEL:
A. Panel Label:
T400HW02 V3
Green mark description
For Pb Free Product, AUO wil add for identification.
For RoHs compatible products, AUO will add for identification.
Note: The green Mark will be present only when the green documents have been ready by AUO internal
green team. (The definition of green design follows the AUO green design checklist.)
B. Carton Label:
8-2 PACKING METHODS:
8-3 Pallet and Shipment Information
Specification
Item Packing Remark
Qty. Dimension Weight (kg)
1 Packing BOX 3pcs/box 1050(L)*280(W)*650(H) 38
2 Pallet 1 1140(L)*1060(W)*138(H) 16
3 Boxes per Pallet 8 boxes/pallet
4 Panels per Pallet 24pcs/pallet
Pallet after packing 24 1140(L)*1060(W)*1438(H) 320
9. PRECAUTIONS
Please pay attention to the followings when you use this TFT LCD module.
9-1 MOUNTING PRECAUTIONS

(1) You must mount a module using holes arranged in four corners or four sides.
(2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not
applied to module. And the case on which a module is mounted should have sufficient
strength so that external force is not transmitted directly to the module.
(3) Please attach the surface transparent protective plate to the surface in order to protect the
polarizer. Transparent protective plate should have sufficient strength in order to the resist
external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the
former generates corrosive gas of attacking the polarizer at high temperature and the latter
causes circuit break by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizer with glass, tweezers or anything harder than
HB pencil lead. And please do not rub with dust clothes with chemical treatment. Do not
touch the surface of polarizer for bare hand or greasy cloth. (Some cosmetics are detrimental
to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft
materials like chamois soaks with petroleum benzene. Normal-hexane is recommended for
cleaning the adhesives used to attach front/ rear polarizer. Do not use acetone, toluene and
alcohol because they cause chemical damage to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer
causes deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.
9-2 OPERATING PRECAUTIONS

(1) The device listed in the product specification sheets was designed and manufactured for TV
application
(2) The spike noise causes the mis-operation of circuits. It should be lower than following
voltage: V=±200mV(Over and under shoot voltage)
(3) Response time depends on the temperature. (In lower temperature, it becomes longer..)
(4) Brightness of CCFL depends on the temperature. (In lower temperature, it becomes lower.)
And in lower temperature, response time (required time that brightness is stable after turned
on) becomes longer.
(5) Be careful for condensation at sudden temperature change. Condensation makes damage to
polarizer or electrical contacted parts. And after fading condensation, smear or spot will
occur.
(6) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(7) Module has high frequency circuits. Sufficient suppression to the electromagnetic
interference shall be done by system manufacturers. Grounding and shielding methods may
be important to minimize the interface.
9-3 ELECTROSTATIC DISCHARGE CONTROL

Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make
certain that treatment persons are connected to ground through wristband etc. And don ’t touch
interface pin directly.
9-4 PRECAUTIONS FOR STRONG LIGHT EXPOSURE

Strong light exposure causes degradation of polarizer and color filter.
9-5 STORAGE
When storing modules as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep
the temperature between 5 and 35 at normal humidity.
(2) The polarizer surface should not come in contact with any other object. It is recommended
that they be stored in the container in which they were shipped.
9-6 HANDLING PRECAUTIONS FOR PROTECTION FILM

(1) The protection film is attached to the bezel with a small masking tape. When the protection
film is peeled off, static electricity is generated between the film and polarizer. This should
be peeled off slowly and carefully by people who are electrically grounded and with well
ion-blown equipment or in such a condition, etc.
(2) When the module with protection film attached is stored for a long time, sometimes there
remains a very small amount of flue still on the Bezel after the protection film is peeled off.
(3) You can remove the glue easily. When the glue remains on the Bezel or its vestige is
recognized, please wipe them off with absorbent cotton waste or other soft material like
chamois soaked with normal-hexane.

Product Description: T400Hw02 TFT-LCD Panel With Rohs Guarantee

Uploaded by

Copyright:

Available Formats

Product Description: T400Hw02 TFT-LCD Panel With Rohs Guarantee

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Product Description: T400Hw02 TFT-LCD Panel With Rohs Guarantee

Uploaded by

Copyright:

Available Formats

Global LCD Panel Exchange Center www.panelook.

Product Description: T400HW02 TFT-LCD PANEL with RoHS guarantee

AUO Model Name: T400HW02 V3

Customer Part No/Project Name:

Customer Signature Date AUO Date

Approved By: PM Director / Frank Hsu

Reviewed By: RD Director / Hong Jye Hong

Reviewed By: Project Leader /Tzuchieh Lai

Prepared By: PM /Cynthia Hung

Document Version: 0.0

40” Full HD Color TFT-LCD Module

(*) Preliminary Specifications

2 ABSOLUTE MAXIMUM RATINGS

3-1 ELECTRIACL CHARACTERISTICS

3-2 INTERFACE CONNECTIONS

3-3 SIGNAL TIMING SPECIFICATION

3-4 SIGNAL TIMING WAVEFORM

3-5 COLOR INPUT DATA REFERENCE

3-6 POWER SEQUENCE

3-7 BACKLIGHT CONNECTOR PIN CONFIGURATION

6 RELIABILITY TEST ITEMS

Items Specification Unit Note

2. Absolute Maximum Ratings

Item Symbol Min Max Unit Condition

Note 1: Duration:50 msec.

3.1 Electrical Characteristics

Input Common Mode Voltage V ICM 0.6 1.2 1.8 V DC 4

3.2 Interface Connections

PIN # Signal Name Description

2 VDD 12V power supply

3 VDD 12V power supply

4 VDD 12V power supply

5 VDD 12V power supply

11 RO_0+ Positive(+) LVDS differential data input

12 RO_1- Negative(-) LVDS differential data input

13 RO_1+ Positive(+) LVDS differential data input

14 RO_2- Negative(-) LVDS differential data input

15 RO_2+ Positive(+) LVDS differential data input

17 RO_CLK- Clock Signal(-)

18 RO_CLK+ Clock Signal(+)

20 RO_3- Negative(-) LVDS differential data input

26 RE_0+ Positive(+) LVDS differential data input

27 RE_1- Negative(-) LVDS differential data input

28 RE_1+ Positive(+) LVDS differential data input

30 RE_2+ Positive(+) LVDS differential data input

32 RE_CLK- Clock Signal(-)

33 RE_CLK+ Clock Signal(+)

35 RE_3- Negative(-) LVDS differential data input

40 SCL EEPROM Serial Clock

41 Reserved Please leave it open

42 Reserved Please leave it open

43 Reserved Please leave it open

45 LVDS Select LVDS data order (NS: High/Open, JEIDA: Low)

46 Reserved Please leave it open

47 Reserved Please leave it open

48 Reserved Please leave it open

49 Reserved Please leave it open

50 Reserved Please leave it open

Pallet after packing 24 1140(L)1060(W)1438(H) 320