T420HW06 V2 Auo

Global LCD Panel Exchange Center www.panelook.
com
T420HW06 V2 Product Specification

Rev. 01
Model Name: T420HW06 V2

Issue Date : 2010/04/24
( )Preliminary Specifications
Ϡ)Final Specifications
(Ϡ
© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 1 / 29
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com

Rev. 01
Contents
No
CONTENTS
RECORD OF REVISIONS
1 GENERAL DESCRIPTION
2 ABSOLUTE MAXIMUM RATINGS
3 ELECTRICAL SPECIFICATION
3-1 ELECTRIACL CHARACTERISTICS
3-2 INTERFACE CONNECTIONS
3-3 SIGNAL TIMING SPECIFICATION
3-4 SIGNAL TIMING WAVEFORM
3-5 COLOR INPUT DATA REFERENCE
3-6 POWER SEQUENCE
3-7 BACKLIGHT SPECIFICATION
4 OPTICAL SPECIFICATION
5 MECHANICAL CHARACTERISTICS
6 RELIABILITY TEST ITEMS
7 INTERNATIONAL STANDARD
7-1 SAFETY
7-2 EMC
8 PACKING
8-1 DEFINITION OF LABEL
8-2 PACKING METHODS
8-3 PALLET AND SHIPMENT INFORMATION
9 PRECAUTION
9-1 MOUNTING PRECAUTIONS
9-2 OPERATING PRECAUTIONS
9-3 ELECTROSTATIC DISCHARGE CONTROL
9-4 PRECAUTIONS FOR STRONG LIGHT EXPOSURE
9-5 STORAGE
9-6 HANDLING PRECAUTIONS FOR PROTECT FILM

Rev. 01
Record of Revision
Version Date Page Description
0.0 2010/02/04 First release
0.1 2010/4/24 19 Update the T2 max to 50 ms

Rev. 01
1. General Description
This specification applies to the 42.0 inch Color TFT-LCD Module T420HW06 V2. This LCD module has a TFT
active matrix type liquid crystal panel 1,920x1,080 pixels, and diagonal size of 42.0 inch. This module supports
1,920x1,080 mode. Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical
stripes. Gray scale or the brightness of the sub-pixel color is determined with a 8-bit gray scale signal for each dot.
The T420HW06 V2 has been designed to apply the 8-bit 2 channel LVDS interface method. It is intended to
support displays where high brightness, wide viewing angle, high color saturation, and high color depth are very
important.
* General Information
Items Specification Unit Note

Active Screen Size 42.02 inch
Display Area 930.24(H) x 523.26(V) mm
Outline Dimension 983.0(H) x 576.0(V) x 52.65(D) mm With inverter cover
Driver Element a-Si TFT active matrix
Display Colors 16.7M Colors
Number of Pixels 1920X1080 Pixel
Pixel Pitch 0.4845 mm
Pixel Arrangement RGB vertical stripe
Display Operation Mode Normally Black
Surface Treatment Anti-Glare, 3H Haze=13%

Rev. 01
2. Absolute Maximum Ratings

The followings are maximum values which, if exceeded, may cause faulty operation or damage to the unit
Item Symbol Min Max Unit Conditions

Logic/LCD Drive Voltage Vcc -0.3 14 [Volt] Note 1
Input Voltage of Signal Vin -0.3 4 [Volt] Note 1
o
Operating Temperature TOP 0 +50 [ C] Note 2
Operating Humidity HOP 10 90 [%RH] Note 2
o
Storage Temperature TST -20 +60 [ C] Note 2
Storage Humidity HST 10 90 [%RH] Note 2
o
Panel Surface Temperature PST 65 [ C] Note 3
Note 1: Duration:50 msec.

Note 2 : Maximum Wet-Bulb should be 39 к and No condensation.
The relative humidity must not exceed 90% non-condensing at temperatures of 40 к or less. At temperatures
greater than 40к, the wet bulb temperature must not exceed 39к.
Note 3: Surface temperature is measured at 50к Dry condition

Rev. 01
3. Electrical Specification
The T420HW06 V2 requires two power inputs. One is employed to power the LCD electronics and to drive the TFT
array and liquid crystal. The second input for BLU is to power inverter.
3.1 Electrical Characteristics

Value
Parameter Symbol Unit Note
Min. Typ. Max
LCD
Power Supply Input Voltage VDD 10.8 12 13.2 VDC 1
Power Supply Input Current IDD 1 1.5 A 2
Power Consumption PC 12 Watt 2
Inrush Current IRUSH 3 A 3
Differential Input High Threshold
VTH -- -- +100 mVDC 4
Voltage
LVDS Differential Input Low Threshold
VTL -100 -- -- mVDC 4
Interface Voltage
Input Common Mode Voltage VICM 0.6 1.2 1.8 VDC 4
LVDS
Input Channel Pair Skew Margin tSKEW (CP) -500 -- +500 ps 5
Interface
VIH
Input High Threshold Voltage 2.7 -- 3.3 VDC
CMOS (High)
Interface VIL
Input Low Threshold Voltage 0 -- 0.6 VDC
(Low)
Backlight Power Consumption PBL 115 Watt
Life Time 50000 -- Hours 8
Note :
1. The ripple voltage should be controlled under 10% of VCC
2. Test Condition:
(1) VDD = 12.0V
(2) Fv = Type Timing, 60Hz
(3) FCLK = Max freq.
(4) Temperature = 25 к
(5) Test Pattern : White Pattern

Rev. 01
3. Measurement condition : Rising time = 400us

μs
4. VICM = 1.25V

5. Input Channel Pair Skew Margin
6. Do not attach a conducting tape to lamp connecting wire. If the lamp wire attach to conducting tape,
TFT-LCD Module have a low luminance and the inverter has abnormal action because leakage current
occurs between lamp wire and conducting tape.
7. The relative humidity must not exceed 80% non-condensing at temperatures of 40 к or less. At
temperatures greater than 40 к, the wet bulb temperature must not exceed 39к. When operate at low
temperatures, the brightness of CCFL will drop and the life time of CCFL will be reduced.
8. Specified values are for a single lamp only which is aligned horizontally. The lifetime is defined as the time
which luminance of the lamp is 50% compared to its original value.
[Operating condition: Continuous operating at Ta = 25±2 ] к

Rev. 01
3.2 Interface Connections
z LCD connector: 187059-51221 (P-TWO, LVDS connector)
z Mating connector:
PIN Symbol Description PIN Symbol Description
1 GND Ground 26 GND Ground
2 NC No connection 27 GND Ground
3 Reserved AUO Internal Use Only 28 CH2_0- LVDS Channel 2, Signal 0-
4 Reserved AUO Internal Use Only 29 CH2_0+ LVDS Channel 2, Signal 0+
5 NC No connection 30 CH2_1- LVDS Channel 2, Signal 1-
6 Reserved AUO Internal Use Only 31 CH2_1+ LVDS Channel 2, Signal 1+
Open/High(3.3V) for NS,
7 LVDS_SEL 32 CH2_2- LVDS Channel 2, Signal 2-
Low(GND) for JEIDA
PWM Dimming signal input
Reserved
8 (AC : 0~3.3V, max:4V, 33 CH2_2+ LVDS Channel 2, Signal 2+
(VBR_EXT)
Duty : 60~100%, freq : 120~240Hz)
Reserved PWM Dimming signal output
9 34 GND Ground
(OPC_OUT) (AC:0~3.3V)
Enable DCR function
Reserved
10 Enable:3.3V(max:4V), 35 CH2_CLK- LVDS Channel 2, Clock -
(OPC Enable)
Disable:0V(or Open)
11 GND Ground 36 CH2_CLK+ LVDS Channel 2, Clock +
12 CH1_0- LVDS Channel 1, Signal 0- 37 GND Ground
13 CH1_0+ LVDS Channel 1, Signal 0+ 38 CH2_3- LVDS Channel 2, Signal 3-
14 CH1_1- LVDS Channel 1, Signal 1- 39 CH2_3+ LVDS Channel 2, Signal 3+
15 CH1_1+ LVDS Channel 1, Signal 1+ 40 Reserved AUO Internal Use Only
16 CH1_2- LVDS Channel 1, Signal 2- 41 Reserved AUO Internal Use Only
17 CH1_2+ LVDS Channel 1, Signal 2+ 42 GND Ground
19 CH1_CLK- LVDS Channel 1, Clock - 44 GND Ground
20 CH1_CLK+ LVDS Channel 1, Clock + 45 GND Ground
22 CH1_3- LVDS Channel 1, Signal 3- 47 NC No connection
23 CH1_3+ LVDS Channel 1, Signal 3+ 48 VDD Power Supply, +12V DC Regulated
24 Reserved AUO Internal Use Only 49 VDD Power Supply, +12V DC Regulated
25 Reserved AUO Internal Use Only 50 VDD Power Supply, +12V DC Regulated
51 VDD Power Supply, +12V DC Regulated

Rev. 01
ÎNS
LVDS Option = High/OpenÎ
" #$ %& ' () * $ )))))))))))))))))))))))))))))))) ' ##$+ ,) * $ ))))))))))))))))))))))))))) $ ,) * $ ))))

! ! ! !
Note: x = 1, 2, 3, 4…
ÎJEIDA
LVDS Option = LowÎ
" #$ %& ' ( ) * $ )))))))))))))))))))))))))))))))) ' ##$+ ,) *$ ))))))))))))))))))))))))))) $ ,) *$ ))))

!

!

!

Note: x = 1, 2, 3, 4…

Rev. 01
3.3 Signal Timing Specification
This is the signal timing required at the input of the user connector. All of the interface signal timing should be
satisfied with the following specifications for its proper operation.
Timing Table
Signal Item Symbol Min. Typ. Max Unit
Period Tv 1090ʳ 1125ʳ 1480ʳ Th

Vertical Section Active Tdisp (v) 1080 Th
Blanking Tblk (v) 10ʳ 45ʳ 400ʳ Th
Period Th 1030ʳ 1100ʳ 1325ʳ Tclk
Horizontal Section Active Tdisp (h) 960 Tclk
Blanking Tblk (h) 70ʳ 140ʳ 365ʳ Tclk
Clock Frequency Fclk=1/Tclk 50ʳ 74.25ʳ 82ʳ MHz
Vertical Frequency Frequency Fv 47ʳ 60ʳ 63ʳ Hz

Horizontal Frequency Frequency Fh 60ʳ 67.5ʳ 73ʳ KHz
Notes:
(1) Display position is specific by the rise of DE signal only.
st st
Horizontal display position is specified by the rising edge of 1 DCLK after the rise of 1 DE, is displayed on the
left edge of the screen.
(2)Vertical display position is specified by the rise of DE after a “Low” level period equivalent to eight times of
st st
horizontal period. The 1 data corresponding to one horizontal line after the rise of 1 DE is displayed at the top
line of screen.
(3)If a period of DE “High” is less than 1920 DCLK or less than 1080 lines, the rest of the screen displays black.
(4)The display position does not fit to the screen if a period of DE “High” and the effective data period do not
synchronize with each other.
Rev. 01
Page 11 / 29
% )/&$
20%1 .&(/0%1
) &+ $
-

) &+$ +%3&.)3,3 &+$ &+$ &+$ &+$ &+$ +%3&.)3,3

3,3
© Copyright AUO Optronics Corp. 2009 All Rights Reserved.

www.panelook.com
4
-

.&(/0-1 20-1

3.4 Signal Timing Waveforms
Global LCD Panel Exchange Center
"&$) "&$) "&$) "&$) "&$) "&$) "&$) "&$) "&$) "&$) "&$) "&$) "&$) "&$) "&$)
!
+%3&.)3,3
!
+%3&.)3,3

"&$) "&$) "&$) "&$) "&$) "&$) "&$) "&$) "&$) "&$) "&$) "&$) "&$) "&$) "&$)

+%3&.)3,3

5

+%3&.)3,3


Rev. 01
3.5 Color Input Data Reference
The brightness of each primary color (red, green and blue) is based on the 8 bit gray scale data input for the color;
the higher the binary input, the brighter the color. The table below provides a reference for color versus data input.
COLOR DATA REFERENCE
Input Color Data

RED GREEN BLUE
Color
MSB LSB MSB LSB MSB LSB
R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
Basic Blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Color Cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
RED(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED(001) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
R ----
RED(254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
GREEN(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
GREEN(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0
G ----
GREEN(254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0
GREEN(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
BLUE(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
BLUE(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
B ----
BLUE(254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0
BLUE(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

Rev. 01
3.6 Power Sequence for LCD
Values
Parameter Unit
Min. Type. Max.
t1 0.4ʳ ---ʳ 30ʳ ms
t2 0.1ʳ ---ʳ 50ʳ ms
t3 300ʳ ---ʳ ---ʳ ms
*1
t4 0 ʳ ---ʳ ---ʳ ms
t5 0ʳ ---ʳ ---ʳ ms
*2
t6 ---ʳ ---ʳ --- ʳ ms
t7 500ʳ ---ʳ ---ʳ ms
Note:
(1) T4=0 : concern for residual pattern before BLU turn off.
(2) T6 : voltage of VDD must decay smoothly after power-off. (customer system decide this value)

Rev. 01
3.7 Backlight Specification
The backlight unit contains 10-I type CCFLs (Cold Cathode Fluorescent Lamp)
3.7.1 Electrical specification
Spec
Item Symbol Condition Unit Note
Min Typ Max
1 Input Voltage VDDB - 21.6 24 26.4 VDC -
2 Input Current IDDB VDDB=24V 4.32 4.79 5.26 ADC 1
3 Input Power PDDB VDDB=24V 115 W 1
4 Inrush Current IRUSH VDDB=24V - - 7.5 ADC 2
5 Operating Frequency FBL VDDB=24V 53 55 57 KHz
ON 2 - 5.5 -
On/Off control voltage VBLON VDDB=24V VDC
6
OFF 0 - 0.8 -
7 On/Off control current IBLON VDDB=24V - - 1.5 mA -
MAX 3.1 - 3.3 VDC -

Dimming Control Voltage V_DIM VDDB=24V
8
MIN - 0 - VDC -
9 Dimming Control Current I_DIM VDDB=24V - - 2 mADC -
10 Internal Dimming Ratio DIM_R VDDB=24V 10 - 100 % 3
MAX VDDB=24V 2 - 3.3 -

External PWM
V_EPWM VDC
11 Control Voltage
MIN VDDB=24V 0 - 0.8 -
External PWM
12 I_EPWM VDDB=24V - - 2 mADC -
Control Current
13 External PWM Duty ratio D_EPWM VDDB=24V 10 - 100 % 3
External PWM
14 F_EPWM VDDB=24V 140 180 240 Hz -
Frequency
ΰ к
Note 1 : Dimming ratio= 100% (MAX) Ta=25±5 , Turn on for 45minutes α
Note 2: Measurement condition Rising time = 20ms (VDDB : 10%~90%);

Rev. 01
3.7.2 Input Pin Assignment
Inverter Connector: CI0114M1HRL-NH (Cvilux)
Pin
Symbol Description
No
1 VDDB Operating Voltage Supply, +24V DC regulated
6 BLGND Ground and Current Return
11 NC No connection
BLU On-Off control:
12 VBLON BL On : High/Open (3.3V~5.5V);
BL off : Low (0~0.8V/GND)
Internal PWM (0~3.3V for 10~100% Duty, open for 100%)
13 VDIM
< NC ; at External PWM mode>
External PWM (10%~100% Duty, open for 100%)
14 PDIM
< NC ; at Internal PWM mode>
(Note*) IF External PWM function includes 10% dimming ratio. Judge condition as below:
(1) Backlight module must be lighted ON normally.
(2) All protection function must work normally.
(3) Uniformity and flicker could NOT be guaranteed

Rev. 01
3.7.3 Power Sequence for Inverter
24V(typ.)
90% 90%
10%
Power Input for BLU
(VDDB)
T1 T2 T5
Dimming Control Signal

(VDIM)
T3 T4
BLU On/Off Enable

(VBLON)
Dip condition for Inverter
Power Input for BLU

(VDDB) T6
VDDB(typ.)*0.8
Value
Parameter Units
Min Typ Max
T1 20 - - ms
T2 500 - - ms
T3 250 - - ms
T4 0 - - ms
T5 1 - - ms
T6 - - 10 ms

Rev. 01
4. Optical Specification
Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 45 minutes in a
dark environment at 25°C. The values specified are at an approximate distance 50cm from the LCD surface at a
viewing angle of ĳ and ș equal to 0°.
Fig.1 presents additional information concerning the measurement equipment and method.
SR3 or equivalent
Values
Parameter Symbol Unit Notes
Min. Typ. Max
Contrast Ratio CR 3200 4000 -- 1
2
Surface Luminance (White) LWH 380 450 -- cd/m 2
Luminance Variation įWHITE(9P) -- -- 1.3 3
Response Time (G to G) TȖ -- 6.5 -- Ms 4
Color Gamut NTSC 72 %
Color Coordinates
Red RX 0.640
RY 0.330
Green GX 0.29
GY 0.6
Typ.-0.03 Typ.+0.03
Blue BX 0.15
BY 0.060
White WX 0.280
WY 0.290
Viewing Angle 5
x axis, right(ĳ=0°) șr -- 89 -- degree
x axis, left(ĳ=180°) șl -- 89 -- degree
y axis, up(ĳ=90°) șu -- 89 -- degree
y axis, down (ĳ=270°) șd -- 89 -- degree
Note:

Rev. 01
1. Contrast Ratio (CR) is defined mathematically as:
Surface Luminance of Lon5
Contrast Ratio=
Surface Luminance of Loff5
2. Surface luminance is luminance value at point 5 across the LCD surface 50cm from the surface with all pixels
displaying white. From more information see FIG 2. When lamp current IH = 11mA. LWH=Lon5 where Lon5 is
the luminance with all pixels displaying white at center 5 location.
3. The variation in surface luminance, įWHITE is defined (center of Screen) as:
įWHITE(9P)= Maximum(Lon1, Lon2,…,Lon9)/ Minimum(Lon1, Lon2,…Lon9)
4. Response time ӫʳ is the average time required for display transition by switching the input signal for five
luminance ratio (0%,25%,50%,75%,100% brightness matrix) and is based on Fv=60Hz to optimize.
Measured Target
Response Time 0% 25% 50% 75% 100%
0% 0% to 25% 0% to 50% 0% to 75% 0% to 100%
25% 25% to 0% 25% to 50% 25% to 75% 25% to 100%
Start 50% 50% to 0% 50% to 25% 50% to 75% 50% to 100%
75% 75% to 0% 75% to 25% 75% to 50% 75% to 100%
100% 100% to 0% 100% to 25% 100% to 50% 100% to 75%
4. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the
horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For
more information see FIG4.
FIG. 2 Luminance
H/2 1 2 3
4 5 6 H
7 8
H/6
V/6 V/2

Rev. 01
FIG.3 Response Time
The response time is defined as the following figure and shall be measured by switching the input signal for “any
level of grey(bright) “ and “any level of gray(dark)”.
Any level of gray (Bright) Any level of gray (Dark) Any level of gray (Bright)
0%, 25%, 50%, 75%, 100% 0%, 25%, 50%, 75%, 100%
90%
Photodetector
Output
10%
0%, 25%, 50%, 75%, 100%
Time
T ӫ (F) T ӫ (R)
FIG.4 Viewing Angle

Rev. 01
5. Mechanical Characteristics
The contents provide general mechanical characteristics for the model T420HW06 V2. In addition the figures in the
next page are detailed mechanical drawing of the LCD.
Horizontal 983.0 mm
Vertical 576.0 mm
Outline Dimension
Depth 52.65 mm (to inverter cover)
Horizontal 939.0mm
Bezel Opening
Vertical 531mm
Horizontal 930.24mm
Active Display Area
Vertical 523.26mm
Weight 10000g (Typ.)
Surface Treatment Anti-Glare, 3H

Rev. 01
Front View

Rev. 01
Back View

Rev. 01
6. Reliability Test Items

Test Item Q’ty Condition
1 High temperature storage test 3 60к, 300hrs
2 Low temperature storage test 3 -20к, 300hrs
3 High temperature operation test 3 50к, 300hrs
4 Low temperature operation test 3 -5к, 300hrs

Wave form: random
Vibration level: 1.5G RMS
5 Vibration test (non-operation) 3 Bandwidth: 10-300Hz,
Duration: X, Y, Z 30min
One time each direction
Shock level: 50G
6 Shock test (non-operation) 3 Waveform: half since wave, 11ms
Direction: ±X, ±Y, ±Z, One time each direction
Random wave (1.5G RMS, 10-200Hz)

7 Vibration test (With carton) 7
30mins/ Per each X,Y,Z axes
Height: 254 mm
8 Drop test (With carton) 7 6 surfaces
(ASTMD 4169-1)

Rev. 01
7. International Standard
7.1 Safety
(1) UL 60950-1, UL 60065; Standard for Safety of Information Technology Equipment Including
electrical Business Equipment.
(2) IEC 60950-1 : 2001, IEC 60065:2001 ; Standard for Safety of International Electrotechnical
Commission
(3) EN 60950 : 2001+A11, EN 60065:2002+A1:2006; European Committee for Electrotechnical
Standardization (CENELEC), EUROPEAN STANDARD for Safety of Information Technology
Equipment Including Electrical Business Equipment.
7.2 EMC
(1) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and
Electrical Equipment in the Range of 9kHz to 40GHz. “American National standards Institute(ANSI),
1992
(2) C.I.S.P.R “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.” International Special committee on Radio Interference.
(3) EN 55022 “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.” European Committee for Electrotechnical Standardization. (CENELEC),
1998

Rev. 01
8. Packing
8-1 DEFINITION OF LABEL:
A. Panel Label:
*xxxxxxxxxxxx-xxxx*
AUO Internal Use

Panel Unique ID
AU Optronics XXXXX MADE IN XXXXX

Manufactured XX/XX XXXXXXX Model NO: T420HW06 V.2
Week Factory Location

Year AUO Internal Use
Green mark description
(1) For Pb Free Product, AUO will add for identification.
(2) For RoHs compatible products, AUO will add RoHS for identification.
Note: The green Mark will be present only when the green documents have been ready by AUO internal green
team. (definition of green design follows the AUO green design checklist.)
B. Carton Label:
QTY : 7


Rev. 01
8-2 PACKING METHODS:
SFV0RGXOH(6'%DJ
SFV0RGXOH(6'%DJ
0RGXOH
&XVKLRQVHW
&XVKLRQVHW
&XVKLRQWRS
&XVKLRQWRS
&XVKLRQGRZQ
&XVKLRQGRZQ
ರ+ರ7DSH
SFVFDUWRQ
SFVFDUWRQ

Rev. 01
8-3 Pallet and Shipment Information
Specification
Item Packing Remark
Qty. Dimension Weight (kg)
1 Packing BOX 7pcs/box 1060(L)*560(W)*680(H) 80
2 Pallet 1 1150(L)*1070(W)*138(H) 16
3 Boxes per Pallet 2 boxes/pallet
4 Panels per Pallet 14pcs/pallet
Pallet after packing 14 1150(L)*1070(W)*818(H) 180
Corner angle Moisture-proof film
Stretch film
Label PET band
Corner angle
Pallet

Rev. 01
9. PRECAUTIONS
Please pay attention to the followings when you use this TFT LCD module.
9-1 MOUNTING PRECAUTIONS

(1) You must mount a module using holes arranged in four corners or four sides.
(2) You should consider the mounting structure so that uneven force (ex. twisted stress) is not applied
to module. And the case on which a module is mounted should have sufficient strength so that
external force is not transmitted directly to the module.
(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter cause circuit
broken by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizer with glass, tweezers or anything harder than HB
pencil lead. And please do not rub with dust clothes with chemical treatment. Do not touch the
surface of polarizer for bare hand or greasy cloth. (Some cosmetics are detrimental to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials
like chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the
adhesives used to attach front/ rear polarizer. Do not use acetone, toluene and alcohol because
they cause chemical damage to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.
9-2 OPERATING PRECAUTIONS

(1) The device listed in the product specification sheets was designed and manufactured for TV
application
(2) The spike noise causes the mis-operation of circuits. It should be lower than following voltage:
V=±200mV(Over and under shoot voltage)
(3) Response time depends on the temperature. (In lower temperature, it becomes longer..)
(4) Brightness of CCFL depends on the temperature. (In lower temperature, it becomes lower.) And in
lower temperature, response time (required time that brightness is stable after turned on) becomes
longer.
(5) Be careful for condensation at sudden temperature change. Condensation makes damage to
polarizer or electrical contacted parts. And after fading condensation, smear or spot will occur.
(6) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(7) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall

Rev. 01
be done by system manufacturers. Grounding and shielding methods may be important to minimize
the interface.
9-3 ELECTROSTATIC DISCHARGE CONTROL
Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain
that treatment persons are connected to ground through wristband etc. And don’t touch interface pin
directly.
9-4 PRECAUTIONS FOR STRONG LIGHT EXPOSURE

Strong light exposure causes degradation of polarizer and color filter.
9-5 STORAGE
When storing modules as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the
temperature between 5 к and 35к at normal humidity.
(2) The polarizer surface should not come in contact with any other object. It is recommended that they
be stored in the container in which they were shipped.
9-6 HANDLING PRECAUTIONS FOR PROTECTION FILM

(1) The protection film is attached to the bezel with a small masking tape. When the protection film is
peeled off, static electricity is generated between the film and polarizer. This should be peeled off
slowly and carefully by people who are electrically grounded and with well ion-blown equipment or
in such a condition, etc.
(2) When the module with protection film attached is stored for a long time, sometimes there remains a
very small amount of glue still on the bezel after the protection film is peeled off.
(3) You can remove the glue easily. When the glue remains on the bezel or its vestige is recognized,
please wipe them off with absorbent cotton waste or other soft material like chamois soaked with
normal-hexane.

T420HW06 V2 Auo

Uploaded by

Document Informationclick to expand document informationpanel 42 pulgadas

Document Informationclick to expand document information

Copyright:

Available Formats

T420HW06 V2 Auo

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

T420HW06 V2 Auo

Uploaded by

Copyright:

Available Formats

Global LCD Panel Exchange Center www.panelook.

T420HW06 V2 Product Specification

Model Name: T420HW06 V2

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 1 / 29

T420HW06 V2 Product Specification

2 ABSOLUTE MAXIMUM RATINGS

3-1 ELECTRIACL CHARACTERISTICS

3-2 INTERFACE CONNECTIONS

3-3 SIGNAL TIMING SPECIFICATION

3-4 SIGNAL TIMING WAVEFORM

3-5 COLOR INPUT DATA REFERENCE

3-6 POWER SEQUENCE

3-7 BACKLIGHT SPECIFICATION

6 RELIABILITY TEST ITEMS

8-1 DEFINITION OF LABEL

8-2 PACKING METHODS

8-3 PALLET AND SHIPMENT INFORMATION

9-1 MOUNTING PRECAUTIONS

9-2 OPERATING PRECAUTIONS

9-3 ELECTROSTATIC DISCHARGE CONTROL

9-4 PRECAUTIONS FOR STRONG LIGHT EXPOSURE

9-6 HANDLING PRECAUTIONS FOR PROTECT FILM

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 2 / 29

T420HW06 V2 Product Specification

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 3 / 29

T420HW06 V2 Product Specification

Items Specification Unit Note

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 4 / 29

T420HW06 V2 Product Specification

2. Absolute Maximum Ratings

Item Symbol Min Max Unit Conditions

Note 1: Duration:50 msec.

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 5 / 29

T420HW06 V2 Product Specification

3.1 Electrical Characteristics

Input Common Mode Voltage VICM 0.6 1.2 1.8 VDC 4

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 6 / 29

T420HW06 V2 Product Specification

5. Input Channel Pair Skew Margin

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 7 / 29

T420HW06 V2 Product Specification

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 8 / 29

T420HW06 V2 Product Specification

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 9 / 29

T420HW06 V2 Product Specification

Period Tv 1090ʳ 1125ʳ 1480ʳ Th

Vertical Frequency Frequency Fv 47ʳ 60ʳ 63ʳ Hz

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 10 / 29

© Copyright AUO Optronics Corp. 2009 All Rights Reserved.

Global LCD Panel Exchange Center www.panelook.com

T420HW06 V2 Product Specification

COLOR DATA REFERENCE

Input Color Data

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 12 / 29

T420HW06 V2 Product Specification

© Copyright AUO Optronics Corp. 2009 All Rights Reserved. Page 13 / 29

T420HW06 V2 Product Specification